OWNER’S OPERATING MANUAL
CW-42i
with
Flat Panel Plasma Display Monitor
Download from Www.Somanuals.com. All Manuals Search And Download.
TABLE OF CONTENTS
Introduction ............................................................................ 2
Important Information .......................................................... 3
Limited Warranty .................................................................. 5
How to Attach Options to the Plasma Monitor.................... 7
Part Names and Functions .................................................... 8
Front View ............................................................................ 8
Rear View / Terminal Board ................................................. 9
Plasma Remote Control ........................................................ 10
Overall Functional Description ............................................. 11
Installation .............................................................................. 12
Plasma Connection Examples................................................ 12
Connecting Your PC or Macintosh Computer ...................... 13
Connecting Your VCR or Laser Disc Player ........................ 13
Connecting Your DVD Player ............................................... 13
Pin Assignments for 15-pin RGB (analog) ........................... 14
Pin Configuration of the RGB3 Connector
(DVI Connector) ................................................................... 14
Basic Operations .................................................................... 15
Power .................................................................................... 15
Volume .................................................................................. 15
Mute ...................................................................................... 15
Display .................................................................................. 15
Timer Off .............................................................................. 15
Aspect Ratio Controls ............................................................ 16
Aspect Ratio Operations (Manual) ........................................ 16
Wide Screen Operation with Computer Signals ................... 17
OSD (On Screen Display) Controls ...................................... 18
Menu Operations ................................................................... 18
PICTURE ADJUST Menu .................................................... 21
AUDIO Menu ........................................................................ 28
IMAGE OPTIONS Menu ..................................................... 30
INSTALL 1 Menu ................................................................. 32
INSTALL 2 Menu ................................................................. 38
INSTALL 3 Menu ................................................................. 46
LANGUAGE Menu .............................................................. 58
COLOR SYSTEM Menu ...................................................... 59
SIGNAL INFO. Menu .......................................................... 60
Table of Signals Supported..................................................... 61
Troubleshooting ...................................................................... 63
Dimensions .............................................................................. 64
Specifications .......................................................................... 65
1
Download from Www.Somanuals.com. All Manuals Search And Download.
INTRODUCTION
» Introduction to the Runco CinemaWall™ CW-42i Flat Panel Display Monitor
The CW-42i is a state-of-the-art, DTV-compatible, flat-panel plasma display monitor. It is high altitude compliant
to 9000 feet. The CW-42i features an anti-glare filter to diffuse direct light sources, making images easier to view
under adverse lighting conditions. Runco incorporates its acclaimed Vivix™ processing into the CW-42i. This
standard video processing includes 3D scan conversion with motion compensation and 3:2 pulldown for excel-
lent video performance with both video-based and film-based material. In addition, multiple aspect ratio control
includes Runco’s VirtualWide™ mode to fill the 16:9 screen with standard 4:3 images without loss of picture
quality. The CW-42i has been carefully engineered for superb video performance. At less than five inches deep,
it can be wall-mounted or used on a tabletop stand.
» The features you’ll enjoy include:
• 16:9 Native Resolution 853 x 480
• DVI Input with HDCP
• IR and discrete RS-232 control for custom installation integration
• High altitude compliant to 9000 feet
• HDTV Compatible
Contents of the package:
• Plasma display monitor
• Power cord
• Remote control with two AAA batteries
• User’s manual
• Safety metal fittings*
• Screws for safety metal fittings*
• Ferrite core (small x 2. large x 2), bands
• Cable clamps
* These are fittings for fastening the unit to a wall to prevent tipping due to external shock when using the
tablestand (optional). Fasten the safety fittings to the holes in the back of the plasma using the safety fitting mount
screws.
Options:
• Wall mount unit
• Tilt mount unit
• Tablestand
2
Download from Www.Somanuals.com. All Manuals Search And Download.
IMPORTANT INFORMATION
» Precautions
Please read this manual carefully before using your plasma monitor and keep the manual handy for future reference.
CAUTION
RISK OF ELECTRIC SHOCK
!
DO NOT OPEN
CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE COVER. NO USER-
SERVICEABLE PARTS INSIDE. REFER SERVICING TO QUALIFIED SERVICE PERSONNEL.
This symbol warns the user that uninsulated voltage within the unit may have sufficient magnitude, it is dangerous
to make any kind of contact with any part inside this unit. This symbol alerts the user that important literature
concerning the operation and maintenance of this unit has been included. Therefore, it should be read carefully
in order to avoid any problems.
WARNING
TO PREVENT FIRE OR SHOCK HAZARDS, DO NOT EXPOSE THIS UNIT TO RAIN OR MOISTURE.
ALSO DO NOT USE THIS UNIT’S POLARIZED PLUG WITH AN EXTENSION CORD RECEPTACLE OR
OTHER OUTLETS, UNLESS THE PRONGS CAN BE FULLY INSERTED. REFRAIN FROM OPENING
THE CABINET AS THERE ARE HIGH-VOLTAGE COMPONENTS INSIDE. REFER SERVICING TO
QUALIFIED SERVICE PERSONNEL.
WARNING
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part
15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference
when the equipment is operated in a commercial environment. This equipment generates, uses, and can radiate
radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause
harmful interference to radio communications. Operation of this equipment in a residential area is likely to cause
harmful interference in which case the user will be required to correct the interference at his own expense.
» Warnings and Safety Precautions
Nomaintenanceotherthancleaningisrequired.Pleaseseethesection“Plasmamonitorcleaningprocedure”onpage 4.
The plasma display panel consists of fine picture elements (cells). There may be some cells that do not produce
light or remain lit. For operating safety and to avoid damage to the unit, read carefully and observe the following
instructions. To avoid shock and fire hazards:
1. Provide adequate space for ventilation to avoid internal heat build-up. Do not cover rear vents or install the unit
in a closed cabinet or shelves. If you install the unit in an enclosure, make sure there is adequate space at the top of
the unit to allow hot air to rise and escape. If the monitor becomes too hot, the overheat protector will be activated
and the monitor will be turned off. If this happens, turn off the power to the monitor and unplug the power cord.
If the room where the monitor is installed is particularly hot, move the monitor to a cooler location, and wait for
60 minutes to cool the monitor. If the problem persists, contact your dealer for service.
2. Do not use this unit’s polarized plug with extension cords or outlets unless the prongs can be completely
inserted.
3. Do not expose the unit to water or moisture.
4. Avoid damage to the power cord, and do not attempt to modify the power cord.
5. Unplug the power cord during electrical storms or if the unit will not be used over a long period.
6. Do not open the cabinet which has potentially dangerous high voltage components inside. If the unit is damaged
in this way the warranty will be void. Moreover, there is a serious risk of electric shock.
7. Do not attempt to service or repair the unit. The manufacturer is not liable for any bodily harm or damage caused
if unqualified persons attempt service or open the back cover. Refer all service to authorized Service Centers.
3
Download from Www.Somanuals.com. All Manuals Search And Download.
Important Information
NOTE:
When you connect a computer to this monitor, use an RGB cable including the ferrite core on both ends of the
cable. And regarding DVI and power cable, attach the supplied ferrite cores. If you do not do this, the monitor
will not conform to mandatory FCC standards. Attaching the ferrite cores: Set the ferrite cores on both ends of
the DVI cable (not supplied), and both ends of the power cable (supplied). Close the lid tightly until the clamps
click. Use the band to fasten the ferrite core (supplied) to the DVI cable.
» To avoid damage and prolong operating life:
1. Use only with 120V 50/60Hz AC power supply. Continued operation at line voltages greater than 120 Volts AC
will shorten the life of the unit, and might even cause a fire hazard.
2. Handle the unit carefully when installing it and do not drop.
3. Set the unit away from heat, excessive dust, and direct sunlight.
4. Protect the inside of the unit from liquids and small metal objects. In case of accident, unplug the power cord
and have it serviced by an authorized Service Center.
5. Do not hit or scratch the panel surface as this causes flaws on the surface of the screen.
6. For correct installation and mounting it is strongly recommended to use a trained, authorized dealer.
7. As is the case with any phosphor-based display (like a CRT monitor, for example) light output will gradually
decrease over the life of a Plasma Display Panel.
8. To avoid sulfurization it is strongly recommended not to place the unit in a dressing room in a public bath or
hot spring bath.
» Plasma monitor cleaning procedure:
1. Use a soft dry cloth to clean the front panel and bezel area. Never use solvents such as alcohol or thinner to
clean these surfaces.
2. Clean plasma ventilation areas with a vacuum cleaner with a soft brush nozzle attachment.
3. To ensure proper ventilation, cleaning of the ventilation areas must be carried out monthly. More frequent
cleaning may be necessary depending on the environment in which the plasma monitor is installed.
Recommendations to avoid or minimize phosphor burn-in:
Like all phosphor-based display devices and all other gas plasma displays, plasma monitors can be susceptible
to phosphor burn under certain circumstances. Certain operating conditions, such as the continuous display of a
static image over a prolonged period of time, can result in phosphor burn if proper precautions are not taken. To
protect your investment in this plasma monitor, please adhere to the following guidelines and recommendations
for minimizing the occurrence of image burn:
* Always enable and use your computer’s screen saver function during use with a computer input source.
* Display a moving image whenever possible.
* Change the position of the menu display from time to time.
* Always power down the monitor when you are finished using it.
If the plasma monitor is in long term use or continuous operation take the following measures to reduce the
likelihood of phosphor burn:
* Lower the Brightness and Contrast levels as much as possible without impairing image readability.
* Display an image with many colors and color gradations (i.e. photographic or photo-realistic images).
* Create image content with minimal contrast between light and dark areas, for example white characters on
black backgrounds. Use complementary or pastel color whenever possible.
* Avoid displaying images with few colors and distinct, sharply defined borders between colors.
NOTE: BURN-INS ARE NOT COVERED BY THE WARRANTY
Contact your dealer for other recommended procedures that will best suit your particular application needs.
4
Download from Www.Somanuals.com. All Manuals Search And Download.
LIMITED WARRANTY
Congratulations on your purchase of a Runco International video product and welcome to the Runco family! We
believe Runco produces “The World’s Finest Home Theater Products”. With proper installation, setup and care,
you should enjoy many years of unparalleled video performance.
This is a LIMITED WARRANTY as defined in the Magnuson-Moss Warranty Act. Please read it carefully and
retain it with your other important documents.
WHAT IS COVERED UNDER THE TERMS OF THIS LIMITED WARRANTY:
SERVICE LABOR: Runco will pay for service labor by a Runco Authorized Service Center when needed as a
result of a manufacturing defect for a period of three (3) years from the effective date of delivery to the end user
(excluding the plasma glass panel).
PARTS: (Not including plasma glass panel) Runco will provide new or rebuilt replacement parts for the parts that
fail due to defects in materials or workmanship for a period of three (3) years from the effective date of delivery
to the end user. Such replacement parts are then subsequently warranted for the remaining portion (if any) of the
original warranty period.
PLASMA GLASS PANEL: Runco will pay for service labor by a Runco Authorized Service Center when needed
as a result of a manufacturing defect for a period of one (1) year from the effective date of delivery to the end
user. In addition, Runco will provide new or rebuilt replacement parts for the parts that fail due to defects in
materials or workmanship for a period of one (1) year from the effective date of delivery to the end user. Such
replacement parts are then subsequently warranted for the remaining portion (if any) of the original warranty
period.
WHAT IS NOT COVERED UNDER THE TERMS OF THIS LIMITED WARRANTY:
Image burn-in on plasma display panels are specifically excluded from coverage under this Limited Warranty.
Image burn-in is the result of misuse of the product and therefore cannot be repaired under the terms of this
Limited Warranty.
TO AVOID IMAGE BURN-IN:
Please ensure that still images are left on your plasma display panel for no more than a few minutes. Also ensure
that images displayed in the 4:3 aspect ratio mode (black or gray stripes, but no picture information is present
on the left and right edges of the screen) are used as infrequently as possible. This will prevent permanent image
burns on your plasma display panel, which can be seen permanently under certain conditions once burn-in has
occurred.
The types of images to avoid include video games, still images and computer screens with stationary tool bars
and icons. (This is why computers are equipped with screen savers – to prevent still images from burning into
the monitor’s phosphors after being displayed continuously for an extended period of time).
Normal viewing material such as television/satellite broadcasts, videotape or DVDs (not put into pause for
extended periods of time) will not cause damage to your display under normal conditions. Many DVD players
are also equipped with screen savers for this reason.
IMPORTANT: Runco is not responsible for image burns on any display. Please exercise caution when
using a 4:3 image on a 16:9 screen.
This Limited Warranty only covers failure due to defects in materials and workmanship that occur during normal
use and does not cover normal maintenance. This Limited Warranty does not cover cabinets or any appearance
items; failure resulting from accident, misuse, abuse, neglect, mishandling, misapplication, faulty or improper
installation or setup adjustments; improper maintenance, alteration, improper use of any input signal; damage
due to lightning or power line surges, spikes and brownouts; damage that occurs during shipping or transit; or
damage that is attributed to acts of God. In the case of remote control units, damage resulting from leaking, old,
damaged or improper batteries is also excluded from coverage under this Limited Warranty.
5
Download from Www.Somanuals.com. All Manuals Search And Download.
Limited Warranty
CAUTION: THIS LIMITED WARRANTY ONLY COVERS RUNCO PRODUCTS PURCHASED FROM
RUNCO AUTHORIZED DEALERS. ALL OTHER PRODUCTS ARE SPECIFICALLY EXCLUDED FROM
COVERAGE UNDER THIS LIMITED WARRANTY. MOREOVER, DAMAGE RESULTING DIRECTLY
OR INDIRECTLY FROM IMPROPER INSTALLATION OR SETUP IS SPECIFICALLY EXCLUDED FROM
COVERAGE UNDER THIS LIMITED WARRANTY.
RIGHTS, LIMITS AND EXCLUSIONS:
Runco limits its obligations under any implied warranties under state laws to a period not to exceed the
warranty period. There are no express warranties. Runco also excludes any obligation on its part for incidental
or consequential damages related to the failure of this product to function properly. Some states do not allow
limitations on how long an implied warranty lasts, and some states do not allow the exclusion or limitation of
incidental or consequential damages. So the above limitations or exclusions may not apply to you. This warranty
gives you specific legal rights, and you may also have other rights that vary from state to state.
EFFECTIVE WARRANTY DATE:
This warranty begins on the effective date of delivery to the end user. For your convenience, keep the original
bill of sale as evidence of the purchase date.
IMPORTANT: WARRANTY REGISTRATION:
Please fill out and mail your warranty registration card. It is imperative that Runco knows how to reach you
promptly if we should discover a safety problem or product update for which you must be notified.
CONTACT A RUNCO AUTHORIZED SERVICE CENTER TO OBTAIN SERVICE:
Repairs made under the terms of this Limited Warranty covering your Runco video product will be performed at
the location of the product, during usual working hours, providing location of product is within normal operating
distance from a Runco Authorized Service Center. In some instances it may be necessary for the product to be
returned to the Runco factory for repairs. If, solely in Runco’s judgment, location of product to be repaired is
beyond normal operating distance of the closest Runco Authorized Service Center, or the repair requires the
unit be returned to the Runco factory, it is the owner’s responsibility to arrange for shipment of the product for
repair. These arrangements must be made through the selling Runco Dealer. If this is not possible, contact Runco
directly for a Return Authorization number and shipping instructions. Runco will return product transportation
prepaid in the United States, unless no product defect is discovered. In that instance, shipping costs will be the
responsibility of the owner.
ADDITIONAL INFORMATION:
To locate the name and address of the nearest Runco authorized service location, or for additional information
about this Limited Warranty, please call or write:
RUNCO INTERNATIONAL
Attn: Customer Service Department
2900 Faber Street
Union City, CA 94587
Ph (510) 324-7777
Fax (510) 324-9300
Toll Free 1-800-23-RUNCO
6
Download from Www.Somanuals.com. All Manuals Search And Download.
HOW TO ATTACH OPTIONS TO THE PLASMA MONITOR
You can attach your optional mounts or stand to the plasma monitor in one of the following two ways:
1) While it is upright. (See drawing A)
2) As it is laid down with the screen face down (See drawing B). Lay the protective sheet, which was wrapped
around the plasma monitor when it was packaged, beneath the screen surface so it does not scratch the screen
face.
* DO NOT touch or hold the screen face when carrying the unit.
• This device cannot be installed on its own. Be sure to use a stand or original mounting unit. (wallmount unit,
stand, etc.)
• For correct installation and mounting, it is required to use a trained, Runco Authorized Dealer. Failure to follow
correct mounting procedures could result in damage to the equipment or injury to the installer. Product warranty
does not cover damage caused by improper installation.
Use only the mounting kit or stand provided by Runco. Refer to mounting kit for detailed instructions.
B
A
Wall
50mm (2")
50mm (2")
Wall
50mm (2")
Ventilation Requirements for enclosure mounting
To allow heat to disperse, leave space between surrounding
objects as shown on the diagram to the right when installing.
7
Download from Www.Somanuals.com. All Manuals Search And Download.
PART NAMES AND FUNCTIONS
» Front View
1
POWER
Turns the plasma monitor’s power on and off.
2
3
4
REMOTE SENSOR WINDOW
Receives the signals from the remote control.
POWER
When the power is on it will light GREEN. When the power is on the standby mode, it will light RED.
INPUT SELECT / EXIT
Switches the input, in the following order. The available inputs depend on the setting of “BNC INPUT”.
RGB:
VIDEO1 VIDEO2 VIDEO3 HD/COMP/DTV
RGB/PC3 RGB/PC2 RGB/PC1
COMP:
VIDEO1 VIDEO2 VIDEO3 HD1/COMP1/DTV1
RGB/PC2 RGB/PC1 HD2/COMP2/DTV2
5
LEFT/- and RIGHT/+
Enlarges or reduces the image. Functions as the CURSOR ( / )
buttons in the On-Screen Display (OSD) mode.
6
7
VOLUME DOWN and UP
Adjusts the volume. Functions as the CURSOR ( / ) buttons in the On-Screen Menu mode.
MENU
Sets the On-Screen Menu mode and displays the main menu.
Located on bottom
of Plasma
Located on bottom
of Plasma
VOLUME
DOWN
INPUTSELECT
/EXIT
MENU
/
ENTER
UP
LEFT/-
RIGHT/+
7
6
5
4
1
3
2
8
Download from Www.Somanuals.com. All Manuals Search And Download.
Part Names and Functions
A
AC IN
Connect the included power cord here.
B
C
Connect speakers (not available from Runco) here. Maintain the correct polarity.
VIDEO 1,2,3 (BNC, RCA, S-Video)
Connect VCR’s, DVD’s or Video Cameras, etc here. VIDEO1 can be used for INPUT or OUTPUT.
D
E
AUDIO1, AUDIO2, AUDIO3
These are audio input terminals. The input is selectable. Set which video image to distribute them from the
audio menu screen.
DVD1 / HD1
Connect DVD’s, High Definition or Laser Disks, etc here.
» Rear View / Terminal Board
F
RGB2 / DVD2 / HD2
RGB2: Connect an analog RGB signal and the synchronization signal.
DVD2 / HD2: Connect DVD’s, High Definition sources, Laser Discs, etc. here.
This input can be set for use with an RGB or Component source.
G
RGB1 (mini D-Sub 15pin)
Connect an analog RGB signal from a computer, etc. here.
This input can be used for Input or Output.
H
I
RGB3 (DVI 24pin)
Connect a digital signal (TMDS) from a source with a DVI output.
EXTERNAL CONTROL
This terminal is used when operating and controlling the monitor externally by RS-232.
Rear View / Terminal Board
VIDEO
1
2
3
C
AUDIO
L
1
R
(MONO)
D
DVD1/HD1
Y
Cb/Pb
E
F
Cr/Pr
R
AUDIO
L
2
(MONO)
DVD2/HD2
RGB2
R
G
Y
B
Cb/Pb
HD
VD
RGB1
D-SUB
G
AUDIO
L
3
R
A
C
I
N
(MONO)
RIGHT
LEFT
SPEAKERS MUST
HAVE MORE THAN
7WATT RATING
OHM
IMPEDANCE
6
DVD3/HD3
RGB3
DVI
H
D-SUB
I
EXTERNAL CONTROL
AC IN
RIGHT
LEFT
SPEAKERS MUST
HAVE MORE THAN
7WATT RATING
OHM
IMPEDANCE
6
A
B
9
Download from Www.Somanuals.com. All Manuals Search And Download.
Part Names and Functions
» Plasma Remote Control
1 ON/OFF
Switches Power ON/OFF.
(This does not operate when POWER/STANDBY indicator of the main unit is off.
2 MENU
Press this button to access the OSD controls. Press this button during the display of the main menu to go to
the sub-menu.
3 CURSOR ( ▲ / ▼ / ◄ / ► )
Use these buttons to select items or settings and to adjust settings or switch the display patterns.
4 LIGHT*
Press this to illuminate the buttons. * Not available on all models.
5 EXIT
Press this button to exit the OSD controls in the main menu.
Press this button during the display of the sub menu to return to the previous menu.
6 VID 1-2-3
Press this button to select VIDEO as the source.
VID1 → VID2 → VID3
VIDEO can also be selected using the INPUT SELECT button on the monitor.
7 ASPECT
1
Press this button to select between aspect ratios.
8 MUTE
Mutes the sound.
9 COMP 1-2
ON
OFF
2
Press this button to select between Component 1 and
Component 2 inputs.
3
5
10 DISPLAY
Displays the source settings on the screen.
11 VOLUME (+/-)
Adjusts the audio volume.
12 RGB 1-2-3
MENU
CODE
EXIT
LIGHT
4
6
Press this button to select RGB/PC as the source.
The available sources depend on the setting of “BNC INPUT”.
7
8
VID
1-2-3
MUTE
ASPECT
10
RGB:
→ RGB1 → RGB2 → RGB3 –
COMP
1-2
DISPLAY
VOL +
VOL -
9
11
13
COMP:
→ RGB1 → RGB3 –
RGB
1-2-3
AUTO
OFF
12
RGB can also be selected using the INPUT SELECT
button on the monitor.
13 AUTO OFF
Use to select AUTO OFF TIMER settings.
10
Download from Www.Somanuals.com. All Manuals Search And Download.
OVERALL FUNCTIONAL DESCRIPTION
DIGITAL INPUTS:
• DVD 1 / HD1
This is a High Definition Digital input. Runco recommends using this digital input whenever possible. This
ensures the highest video quality because the signal is carried in the digital domain throughout the entire signal
path, from source component output, into the plasma. This maintains maximum signal purity.
Connect Digital High Definition sources that have a DVI output, such as HD tuners and set top boxes, satellite
receivers, DVD players, etc.
ISF Calibration:
This display device has been designed to incorporate setup and calibration standards established by the Imaging
Science Foundation (ISF). The ISF has developed carefully crafted, industry-recognized standards for optimal
video performance and has implemented a training program for technicians and installers to use these standards
to obtain optimal picture quality from Runco video display devices. Accordingly, Runco recommends that setup
and calibration be performed by an ISF certified installation technician.
11
Download from Www.Somanuals.com. All Manuals Search And Download.
INSTALLATION
» Plasma Connection Examples
VIDEO
VIDEO 1-3
1
To video inputs on
the plasma monitor
2
3
AUDIO 1
L
R
(MONO)
VCR or Laser Disc Player
DVD1/HD1
Y
Cb/Pb
Cr/Pr
AUDIO 2
L
R
(MONO)
DVD2/HD2
RGB2
DVD Player
R
G
B
Y
IBM VGA or Compatibles
Cb/Pb
HD
VD
Macintosh or Compatibles
(Desktop type)
RGB1
D-SUB
AUDIO 3
L
R
(MONO)
Monitor adapter for Macintosh
DVD3/HD3
RGB3
DVI
HD Set Top Box with DVI HDCP Output
To Mini D-Sub 15 pin connector
on the plasma monitor
D-SUB
EXTERNAL CONTROL
12
Download from Www.Somanuals.com. All Manuals Search And Download.
Installation
» Connecting Your PC or Macintosh Computer
Connecting your PC or Macintosh computer to your plasma monitor will enable you to display your computer’s
screen image for an impressive presentation. The plasma monitor supports the signals described on page 61.
To connect a PC, Macintosh or compatible graphics adapter, simply:
1. Turn off the power to your plasma monitor and computer.
2. If your PC does not support SXGA/XGA/SVGA/VGA you will need to install an SXGA/XGA/SVGA/
VGA graphics board. Consult your computer’s owner’s manual for your SXGA/XGA/SVGA/VGA configuration.
If you need to install a new board, see the manual that comes with your new graphics board for installation
instructions.
3. This plasma monitor provides signal compatibility up to VESA 1600 x 1200 (UXGA). However, it is not
recommended to use this resolution due to image readability on the monitor’s native pixel resolution panel.
4. Use the signal cable to connect your PC or Macintosh computer to the plasma monitor. For Macintosh, use the
monitor adapter to connect to your computer’s video port, if necessary.
5. Turn on the plasma monitor and the computer.
6. If the plasma monitor goes blank after a period of inactivity, it may be caused by a screen saver installed on the
computer you’ve connected to the plasma monitor.
When using a Macintosh with the plasma monitor, the following four display standards are supported using
the Macintosh adapter: (1) 13” fixed mode; (2) 16” fixed mode; (3) 19” fixed mode; (4) 21” fixed mode
The 13” fixed mode is recommended for your 42” Wide VGA.
» Connecting Your VCR or Laser Disc Player:
Use common RCA cables (not provided) to connect your VCR or laser disc player to your plasma monitor.
To make these connections, simply:
1. Turn off the power to your plasma monitor and VCR or laser disc player.
2. Connect one end of your RCA cable to the video output connector on the back of your VCR or laser disc
player, connect the other end to the Video input on your plasma monitor. Use standard RCA audio patch cords
to connect the audio from your VCR or laser disc player to your plasma monitor (if your VCR or laser disc player
has this capability). Be careful to keep your right and left channel connections correct for stereo sound.
3. Turn on the plasma monitor and the VCR or laser disc player.
Note:
Refer to your VCR or laser disc player owner’s manual for more information about your equipment’s video
output requirements.
» Connecting Your DVD Player:
You can connect your plasma monitor to a DVD player. To do so, simply:
1. Turn off the power to your plasma monitor and DVD player.
2. Use a component video cable to connect your DVD player to the Y, Cb, and Cr inputs on your plasma
monitor. Or use the DVD-player’s S-Video output. Use a standard S-Video cable to connect to the S-Video input
on the plasma monitor.
3. Turn on the plasma monitor and the DVD player.
13
Download from Www.Somanuals.com. All Manuals Search And Download.
Installation
» Pin Assignments for 15-pin RGB (analog)
Pin No.
Signal (Analog)
1
2
3
4
5
Red
Green or sync-on-green
Blue
No connection
Ground
5
4
3
2
1
10
9
8
7
6
15 14 13 12 11
6
Red ground
7
Green ground
8
Blue ground
9
No connection
Sync signal ground
No connection
Bi-directional DATA (SDA)
Horizontal sync or Composite sync
Vertical sync
10
11
12
13
14
15
Data clock
» Pin Configuration of the RGB3 Connector (DVI Connector)
The unit is equipped with a type of connector commonly used for digital.
(This cannot be used for an analog input.)
Pin No.
Signal (Digital)
Pin No.
13
14
15
16
17
18
19
20
Signal (Digital)
No connection
+5V Power
RGB 3
1
2
3
4
5
6
7
8
T.M.D.S Data 2 -
T.M.D.S Data 2 +
T.M.D.S Data 2 Shield
No connection
No connection
DDC Clock
Ground
1
9
2
3
4
5
6
7
8
10 11 12 13 14 15 16
Hot Plug Detect
T.M.D.S Data 0 -
T.M.D.S Data 0 +
T.M.D.S Data Shield
No connection
17 18 19 20 21 22 23 24
DDC Data
No connection
9
T.M.D.S Data 1 -
T.M.D.S Data 1 +
T.M.D.S Data 1 Shield
No connection
21
22
23
24
No connection
10
11
12
T.M.D.S Clock Shield
T.M.D.S Clock +
T.M.D.S Clock -
14
Download from Www.Somanuals.com. All Manuals Search And Download.
BASIC OPERATIONS
» POWER
To turn the unit ON and OFF:
1. Plug the power cord into an active AC power outlet.
2. Press the POWER ON button (on the remote control or control panel) to turn on the unit.
The monitor’s POWER/STANDBY indicator will light up (green) when the unit is on.
3. Press the POWER OFF button (on the remote control or control panel) to turn off the unit.
The monitor’s POWER/STANDBY indicator turns red and the standby mode is set (only when turning off the unit
with the remote control).
» VOLUME
To adjust the sound volume:
1. Press and hold the VOLUME (+) button (on the remote control or the unit) to increase to the desired level.
2. Press and hold the VOLUME (-) button (on the remote control or the unit) to decrease to the desired level.
» MUTE
To cancel the sound:
Press the MUTE button on the remote control to cancel the sound; press again to restore.
» DISPLAY
To check the settings:
1. The screen changes each time the DISPLAY button is pressed.
2. If the button is not pressed for approximately three seconds, the menu turns off.
» TIMER OFF
To set the timer off:
The timer off can be set to turn the power off after 30, 60, 90 or 120 minutes
1. Press the AUTO OFF button to start the timer at 30 minutes.
2. Press the AUTO OFF button to the desired time.
TIMER OFF 30
3. The timer starts when the menu turns off.
30 60 90 120 0 ┐
To check the remaining time:
1. Once the off timer has been set, press the AUTO OFF button once.
2. The remaining time is displayed, then turns off after a few seconds.
3. When five minutes remain the remaining time appears until it reaches zero.
To cancel the off timer:
1. Press the AUTO OFF button twice in a row.
2. The off timer is canceled.
NOTE:
After the power is turned off with the timer off... A slight current is still supplied to the monitor. When you are
leaving the room or do not plan to use the system for a long period of time, turn off the power of the monitor.
15
Download from Www.Somanuals.com. All Manuals Search And Download.
ASPECT RATIO CONTROLS
» Aspect Ratio Operations (Manual)
There are four aspect ratios available that can be selected for video signal inputs.
When viewing videos or DVDs:
1. Press the ASPECT button on the remote control.
2. Within 3 seconds...
Press the ASPECT button again. The screen size switches as follows:
LTR BOX STD (4:3) ANAMPHC VRTWIDE
LTR BOX mode
STD 4:3 mode
The image in the Letterbox mode will be zoomed in,
and the top and bottom portion ‘blanked off.’ This ratio
is best suited for LaserDisc movies or non-anamorphic
DVD’s.
The input signal will be scaled to fit in the center of the
16:9 screen.
Active Image Area
Active
Image
Area
ANAMPHC mode
VIRTUALWIDE mode
The image is compressed vertically, but anamorphic
software will appear properly proportioned. This is This aspect ratio is designed to fill the 16:9 screen
best suited for use with 16:9 DVD’s.
with a 4:3 image. The center of the picture is not
stretched, and it gradually stretches on the sides
reaching the most extreme stretch at the far edges of
the picture. (non-linear scaling) In addition, we apply
a very slight vertical stretch uniformly (no graduation)
which results in a very small amount of cropping
of the top and bottom of the image area. Thus a 4:3
image is transformed into a 16:9 image with minimal
distortion.
Active Image Area
Active
Image
Area
16
Download from Www.Somanuals.com. All Manuals Search And Download.
Aspect Ratio Controls
» Wide Screen Operation with Computer Signals
Switch to the wide screen mode to expand the 4:3 image to fill the entire screen.
1. Press the ASPECT button on the remote control.
2. Within 3 seconds...
Press the ASPECT button again.
The screen size switches as follows:
STD (4:3) ANAMPHC LTR BOX
STD 4:3 mode (4:3 or SXGA 5:4)
Active
Image
Area
The picture has the same size as the normal computer image.
ANAMPHC mode
Active Image Area
The image is expanded in the horizontal direction.
Information
LTR BOX mode
■ Supported resolution
See page 61 for details on the display output of the various
VESA signal standards supported by the monitor.
■ When 853 (848) dot x 480 line wide VGA *signals
with a vertical frequency of 60 Hz and horizontal
frequency of 31.7 (31.0) kHz are input.
Active Image Area
Select an appropriate setting for RGB SELECT mode
referring to the “Table of Signals Supported” on page 61.
* “IBM PC/AT” and “VGA” are registered trademarks of
IBM, Inc. of the United States.
When wide signals are input.
NOTE:
Do not leave the displayed in 4:3 mode for an extended period. This can cause a phosphor burn-in.
17
Download from Www.Somanuals.com. All Manuals Search And Download.
OSD (ON SCREEN DISPLAY) CONTROLS
» Menu Operations
The OSD window is displayed with respect to the screen as shown on the diagram.
* Depending on the screen’s mode, the OSD may be displayed differently. In the explanation, the OSD section is
shown close up.
The following describes how to use the menus and the selected items.
1. Press the MENU button on the remote control to display the MAIN MENU.
CINEMAWALL
PICTURE ADJUST
1
/
2
AUDIO
IMAGE OPTIONS
INSTALL
INSTALL
INSTALL
1
2
3
ADVANCED OSD: ON
NEXT PAGE
MENU/ENTER
EXIT
EXIT
SEL.
ENTER
2. Press the MENU button on the remote control to select a submenu or item.
CINEMAWALL
PREVIOUS PG
LANGUAGE
2 / 2
CINEMAWALL
PICTURE ADJUST
1 / 2
AUDIO
COLOR SYSTEM
SIGNAL INFO.
IMAGE OPTIONS
INSTALL 1
INSTALL 2
INSTALL 3
MENU/ENTER
EXIT
EXIT
SEL.
ENTER
ADVANCED OSD: ON
NEXT PAGE
MENU/ENTER
EXIT
SEL.
OK
EXIT
3. Press the cursor buttons
on the remote control to highlight the menu you wish to enter.
PICTURE ADJUST
1 / 2
CONTRAST
58
56
52
49
50
BRIGHTNESS
SHARPNESS
COLOR
TINT
PICTURE MEM
VIDEO NR
:
NORMAL
OFF
:
NEXT PAGE
ADJ.
EXIT
SEL.
RETURN
4. Adjust the level or change the setting of the selected item by using the cursor buttons ◄► on the remote
control.
5. Change the adjustments or the settings that are stored in memory. The change is stored until you change it
again.
6. Repeat steps 2-5 to adjust an additional item, or press the EXIT button on the remote control to return to the
main menu.
NOTE:
The main menu disappears by pressing the EXIT button.
18
Download from Www.Somanuals.com. All Manuals Search And Download.
OSD (On Screen Display) Controls
Main Menu
Sub Menu
CONTRAST
BRIGHTNESS
SHARPNESS
COLOR
Functions
Default
Reset
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
PICTURE
ADJUST
Adjusts the contrast.
Center
Center
Adjusts the brightness.
Adjusts the sharpness
Center
Adjusts the color.
Center
TINT
Adjusts the tint.
Center
CONTRAST
PICTURE MEM
VIDEO NR
KELVIN
Sets the image memory according to the VIDEO environment and image S/W.
Reduces noise visible in image.
OFF
8500K
Center
Center
Center
Center
Center
Center
OFF
Adjusts the color temperature and white balance.
Adjusts the red content (signal level).
Adjusts the green content (signal level).
Adjusts the blue content (signal level).
Adjusts the red content (black level).
Adjusts the green content (black level).
Adjusts the blue content (black level).
Resets the WHITE BALANCE settings to the factory default values.
Adjusts the brightness of midtone areas.
Enables high-quality dark area reproduction.
Adjusts hue and color density of red.
Adjusts hue and color density of green.
Adjusts hue and color density of blue.
Adjusts hue and color density of yellow.
Adjusts hue and color density of magenta.
Adjusts hue and color density of cyan.
Resets COLOR CHART settings to the factory default values.
RED GAIN
WHITE
BALANCE
GREEN GAIN
BLUE GAIN
RED OFFSET
GREEN OFFSET
BLUE OFFSET
RESET
GAMMA
2.2
DITHER
AUTO
Center
Center
Center
Center
Center
Center
OFF
COLOR CHART
RED
GREEN
BLUE
YELLOW
MAGENTA
CYAN
RESET
Main Menu
AUDIO
Sub Menu
BASS
Functions
Default
Center
Center
Center
*1
Reset
Yes
Sets the bass.
TREBLE
Sets the treble.
Yes
BALANCE
AUDIO INPUT 1-3
Sets the left/right balance.
Sets the allocation of the audio connectors.
Yes
Yes
Main Menu
Sub Menu
ASPECT RATIO
V SHIFT
Functions
Default
--
Reset
--
IMAGE
OPTIONS
Selects between the different aspect ratio modes.
Adjusts the vertical position.
Adjusts the horizontal position.
Adjusts the vertical size.
Center
Center
Min
Yes
Yes
Yes
Yes
No
H SHIFT
V-SIZE
H-SIZE
Adjusts the horizontal size.
Min
COMPUTER
Turn this on to have the monitor automatically adjust “FINE PICTURE” and
“PICTURE ADJ”
OFF *
FINE PICTURE
PICTURE ADJ
Adjusts for flickering on the computer image.
Min *2
Yes
Yes
Adjusts for striped patterns on the computer image.
Center *2
Main Menu
Sub Menu
OSD
Functions
Defaults
ON
Reset
Yes
Yes
Yes
Yes
Yes
--
INSTALL 1
DISPLAY OSD
OSD ADJ.
When set to OFF, the on-screen menu is not displayed.
Sets the position of the menu.
1
OSD POSITION
OSD ORBITER
Sets the display format as a horizontal or vertical screen.
Sets the OSD not to be displayed at the same position.
Sets the BNC connectors.
H
OFF
RGB
RGB
AUTO
BNC INPUT
D-SUB TYPE
RGB TYPE
Checks the signal being transmitted to RGB1 terminal.
Sets the appropriate mode for the computer image.
19
Yes
Download from Www.Somanuals.com. All Manuals Search And Download.
OSD (On Screen Display) Controls
Main Menu
Sub Menu
Functions
Default
Reset
RGB (VGA signals), VIDEO (Moving picture), WIDE (Wide VGA), DTV.
Sets the digital broadcasting (1080A, 1080B, 1080C) or the High Vision (1035I).
Skips over signals which are not present.
HD TYPE
1080B
OFF
--
No
Yes
--
INPUT SKIP
FACTORY
Resets all the settings (PICTURE ADJ, AUDIO, IMAGE OPT, INSTALL 1-3,
etc.) to the factory default values.
Main Menu
Sub Menu
Functions
Default
OFF
ON
Reset
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
INSTALL 2
AUTO OFF
Sets the monitor for use as an energy-saving display when used with a computer.
Sets the picture to suit the movie.
CINEMA MODE
PDP PROTECT
LUM. SETTING
ORBITER
Limits screen brightness to reduce burn-in on the display.
Moves the picture intermittently.
AUTO
OFF
OFF
OFF
OFF
3
INVERSE
Displays a negative/positive inverse image or an all-white screen.
Sweeps the screen with a white vertical bar.
Softens the detail in 4 steps (1-4)
IMAGE SWEEP
SOFTEN
SIDEBAR ADJ
S1/S2
In case of 4:3, sets the luminance of both sides.
Resizes the S-video image to best fit the display.
OFF
Main Menu
Sub Menu
TIMER
Functions
Defaults
--
Reset
No
INSTALL 3
PRESENT TIME
PROGRAM
Sets the day of the week and the time.
Sets the ON/OFF time for switching on the power and the input mode.
Sets the input mode at the time the power is switched on.
Disables the function of the front panel buttons.
Disables the transmission of the remote control.
When set to ON, the received signal will be looped out.
OFF
LAST
OFF
ON
Yes
Yes
Yes
Yes
Yes
INPUT SELECT
CONTROL LOCK
IR ENABLE
LOOP OUT
OFF
Main Menu
Sub Menu
Functions
Default
ALL
OFF
--
Reset
Yes
Yes
--
ID NUMBER
DIVIDER
Sets ID number for the display.
VIDEO WALL
Creates a 2x2 or 3x3 video wall.
Sets the position.
POSITION
DISP. MODE
AUTO ID
Selects the screen mode from between Splitting and Blanking.
Automatically sets the ID number of multiple displays.
Adjusts the position of the image, etc.
SPLIT
OFF
--
Yes
Yes
--
IMAGE OPT
P. ON DELAY When set to ON, each display turns on after a delay time.
OFF
OFF
Yes
Yes
LUM SET
LINK
Sets a uniform brightness for each display.
REPEAT-
TIMER
Sets two programmable timers.
OFF
Yes
Main Menu
Sub Menu
Functions
Default
English
AUTO
Reset
No
LANGUAGE
Sets the language of the menus (English, German, French, Italian, Spanish).
COLOR
SYSTEM
Sets the VIDEO format (AUTO, PAL, PAL-M, PAL-N, PAL60, SECAM, 4.43
NTSC or 3.59 NTSC).
No
SIGNAL INFO.
Used to check the frequency and synchronizing polarities of the active signal
being input.
--
--
*1 AUDIO INPUT 1: VIDEO 1 AUDIO INPUT 2: HD/DVD1 AUDIO INPUT 3: RGB1
*2 RGB/PC only
20
Download from Www.Somanuals.com. All Manuals Search And Download.
OSD (On Screen Display) Controls
» PICTURE ADJUST Menu
Adjusting the picture
The contrast, brightness, sharpness, color and tint can be adjusted as desired.
Example: Adjusting the contrast
Press the MENU button on the remote control to display the MAIN MENU on the screen, then...
1. Use the and buttons to select “PICTURE ADJUST”, then press the MENU button.
The “PICTURE ADJUST” screen appears.
2. Use the and buttons to select “CONTRAST”.
PICTURE ADJUST
1 / 2
CONTRAST
58
56
52
49
50
BRIGHTNESS
SHARPNESS
COLOR
TINT
PICTURE MEM
VIDEO NR
:
NORMAL
OFF
:
NEXT PAGE
EXIT
SEL.
ADJ.
RETURN
3. Use the and buttons to adjust the contrast.
CONTRAST
58
* If neither or buttons is pressed within 5 seconds, the current setting is set and the previous screen
reappears.
4. Once the adjustment is completed...
Press the EXIT button to return to the main menu. To delete the main menu, press the EXIT button once more.
NOTE:
If “CAN NOT ADJUST” appears...
When trying to enter the PICTURE submenu, make sure PICTURE MEM is not set to FACTORY.
Information
■ Picture adjustment screen
CONTRAST .........
BRIGHTNESS .....
SHARPNESS .......
Changes the picture’s white level.
Changes the picture’s black level.
Changes the picture’s sharpness.
Adjusts picture detail of VIDEO
display.
COLOR ...............
TINT ....................
Changes the color density.
Changes the picture’s tint. Adjust for
natural colored skin, background, etc.
■ Adjusting the computer image
Only the contrast and brightness can be adjusted when a computer
signal is connected.
■ Restoring the factory default settings
Select “FACTORY” under the “PICTURE MEM” settings.
21
Download from Www.Somanuals.com. All Manuals Search And Download.
OSD (On Screen Display) Controls
Setting the picture mode according to the brightness of the room
There are four picture modes that can be used effectively according to the environment in which you are viewing
the display.
Example: Setting the “CUSTOM1” mode
Press the MENU button on the remote control to display the MAIN MENU on the screen, then...
1. Use the and buttons to select “PICTURE ADJUST”, then press the MENU button. The “PICTURE
ADJUST” screen appears.
2. Use the and buttons to select “PICTURE MEM”
PICTURE ADJUST
1 / 2
CONTRAST
58
56
52
49
50
BRIGHTNESS
SHARPNESS
COLOR
TINT
PICTURE MEM
VIDEO NR
:
CUSTOM1
OFF
:
NEXT PAGE
EXIT
SEL.
ADJ.
RETURN
3. To set to “CUSTOM1” ...
Use the and buttons to select “CUSTOM1”. The mode switches as follows when the and buttons are
pressed:
PICTURE MEM
:
CUSTOM1
NORMAL ISF DAY ISF NIT CUSTOM1 FILM
If neither the or button is pressed within 5 seconds, the current selection is set and the previous screen
reappears.
4. Once the adjustment is completed...
Press the EXIT button to return to the main menu. To delete the main menu, press the EXIT button once more.
Information
■ Types of picture modes
ISF DAY and ISF NIT (NIGHT)
Set this mode when watching video in a dark room. This mode
provides darker, finer pictures, like the screen in movie theaters.
For a darker image, select ISF NIT.
NORMAL
Set this mode when watching video in a bright room. This mode
provides dynamic pictures with distinct differences between light
and dark sections.
FILM
Use this setting for brightness.
CUSTOM1
Use this to reset the picture to the factory default settings.
22
Download from Www.Somanuals.com. All Manuals Search And Download.
OSD (On Screen Display) Controls
Reducing noise in the picture
Use these settings if the picture has noise due to poor reception or when playing video tapes on which the picture
quality is poor.
Example: Setting “VID NR3”
Press the MENU button on the remote control to display the MAIN MENU on the screen, then...
1. Use the and buttons to select “PICTURE ADJUST”, then press the MENU button. The “PICTURE
ADJUST” screen appears.
2. Use the and buttons to select “VIDEO NR”.
PICTURE ADJUST
1 / 2
CONTRAST
58
56
52
49
50
BRIGHTNESS
SHARPNESS
COLOR
TINT
PICTURE MEM
VIDEO NR
:
CUSTOM1
OFF
:
NEXT PAGE
EXIT
SEL.
ADJ.
RETURN
3. Use the and buttons to select “VID NR3”.
The mode switches as follows when the and buttons are pressed:
OFF VID NR1 VID NR2 VID NR3
VIDEO NR
:
VID NR3
* If neither the or button is pressed within 5 seconds, the current selection is set and the previous screen
reappears.
4. Once the setting is completed...
Press the EXIT button to return to the main menu. To delete the main menu, press the EXIT button once more.
Information:
■ VIDEO NR
* “NR” stands for Noise Reduction.
* This function reduces noise in the picture.
■ Types of noise reduction
There are three types of noise reduction. Each has a different level of noise reduction. The effect becomes stronger as the number
increases (in the order VID NR1 VID NR2 VID NR3).
OFF ..... Turns the noise reduction function off.
23
Download from Www.Somanuals.com. All Manuals Search And Download.
OSD (On Screen Display) Controls
Setting the KELVIN
Use this procedure to set color tone produced by the plasma display.
Example: Setting “6500K”
Press the MENU button on the remote control to display the MAIN MENU on the screen, then...
1. Use the and buttons to select “PICTURE ADJUST”, then press the MENU button. The “PICTURE
ADJUST” screen appears.
2. Use the and buttons to select “KELVIN”.
3. Use the and buttons to select “6500K”.
The mode switches as follows when the and buttons are pressed:
5400K 6500K 8500K 9300K
* See below to set “WHITE BALANCE ”.
PICTURE ADJUST
2 / 2
PREVIOUS PG
KELVIN
:
:
:
6500K
2.2
GAMMA
DITHER
AUTO
COLOR CHART
MENU/ENTER
EXIT
SEL.
ENTER
RETURN
* If neither the or button is pressed within 5 seconds, the current selection is set and the previous screen
reappears.
4. Once the setting is completed...
Press the EXIT button to return to the main menu. To delete the main menu, press the EXIT button once more.
Information
■ Setting the color temperature
5400K ................ Redder
6500K ................ Slightly redder
8500K ................ Standard (slightly bluer)
9300K ................ Bluer
■ Restoring the factory default settings
Select “FACTORY” under the INSTALL 1 menu. Note that this
also restores other settings to the factory defaults.
24
Download from Www.Somanuals.com. All Manuals Search And Download.
OSD (On Screen Display) Controls
Adjusting the Color to the Desired Level
Use this procedure to adjust the white balance for each color temperature to achieve the desired color quality.
Example: Adjusting the “RED GAIN” of “9300K” color temperature.
Perform the following operations.
Press the MENU button on the remote control to display the MAIN MENU on the screen, then...
Perform Steps 1-3 of KELVIN, then...
4. Press the MENU button. The “WHITE BALANCE” screen appears.
5. Use the and buttons to select “RED GAIN”.
WHITE BALANCE
KELVIN 6500K
RED GAIN
60
61
60
50
50
50
GREEN GAIN
BLUE GAIN
RED OFFSET
GREEN OFFSET
BLUE OFFSET
RESET
: OFF
EXIT
RETURN
SEL.
ADJ.
RED GAIN
0
6. Adjust the white balance using the and buttons.
* If neither the and buttons is pressed within 5 seconds, the current setting is set and the previous screen
reappears.
7. Once the adjustment is completed...
Press the EXIT button to return to the main menu. To delete the main menu, press the EXIT button once more.
Information
■ Adjusting the white balance
R/G/B GAIN ..... White balance adjustment for signal level
R/G/B OFFSET . .White balance adjustment for black level
RESET .................... Resets settings to the factory default
values. Use and buttons to select
“ON”, then press the MENU button.
■ Restoring the factory default settings
Select “RESET” under the WHITE BALANCE menu.
25
Download from Www.Somanuals.com. All Manuals Search And Download.
OSD (On Screen Display) Controls
Changing the GAMMA
This feature adjusts the brightness of the midtone areas while keeping shadows and highlights unchanged.
Example: Setting “2.8”
Perform the following operations.
Press the MENU button on the remote control to display the MAIN MENU on the screen, then...
1. Use the ▲ and ▼ buttons to select “PICTURE ADJUST”, then press the MENU button. The “PICTURE
ADJUST” screen appears.
PICTURE ADJUST
2 / 2
2. Use the ▲ and ▼ buttons to select “GAMMA”.
PREVIOUS PG
COLOR TEMP.
GAMMA
:
:
:
6500K
2.2
3. Use the and buttons to select “2.8”.
The mode switches as follows each time the or button is pressed:
1.8 2.2 2.5 2.8
DITHER
AUTO
COLOR CHART
EXIT
RETURN
SEL.
ADJ.
4. Once the setting is completed...
Press the EXIT button to return to the main menu.
To delete the main menu, press the EXIT button once more.
Information
■ GAMMA settings
The picture becomes darker as the number increases (in the sequence of 1.8, 2.2, 2.5, 2.8).
■ Restoring the factory default settings
Select “FACTORY” under the INSTALL 1 menu. Note that this also restores other settings to the factory defaults.
Making the DITHER Adjustments
This feature allows more detailed tone to be reproduced especially in the dark area.
Example: Setting “2.2”
Perform the following operations.
Press the MENU button on the remote control to display the MAIN MENU on the screen, then...
1. Use the and buttons to select “PICTURE ADJUST”, then press the MENU button. The “PICTURE
ADJUST” screen appears.
2. Use the and buttons to select “DITHER”.
PICTURE ADJUST
2 / 2
PREVIOUS PG
3. Use the and buttons to select “AUTO”.
The mode switches as follows each time the or button is pressed:
AUTO STILL MOTION DIFFUSE
KELVIN
:
:
:
6500K
2.2
GAMMA
DITHER
AUTO
COLOR CHART
EXIT
RETURN
SEL.
ADJ.
4. Once the setting is completed...
Press the EXIT button to return to the main menu.
To delete the main menu, press the EXIT button once more.
26
Download from Www.Somanuals.com. All Manuals Search And Download.
OSD (On Screen Display) Controls
Information
■ DITHER settings
AUTO ................ Will automatically appraise the picture and make adjustments.
STILL ................ Will apply the dither method suitable for still pictures.
MOTION ........... Will apply the dither method suitable for motion pictures.
DIFFUSE ........... Will apply the error diffusion method.
■ Restoring the factory default settings
Select “FACTORY” under the INSTALL 1 menu. Note that this also restores other settings to the factory defaults.
Adjusting the Colors
Use this procedure to adjust hue and color density for red, green, blue, yellow, magenta and cyan. Such adjustments
will not affect the other colors. You can accentuate the green color of trees, the blue of the sky, etc.
Example: Adjusting the color tune for blue
Perform the following operations.
Press the MENU button on the remote control to display the MAIN MENU on the screen, then...
1. Use the ▲ and ▼ buttons to select “PICTURE ADJUST”, then press the MENU button. The “PICTURE
ADJUST” screen appears.
2. Use the ▲ and ▼ buttons to select “COLOR CHART”, then press the MENU button. The “COLOR CHART”
screen appears.
COLOR CHART
RED
Y
C
M
G
R
B
M 0
Y 0
C 0
R 0
B 0
G 0
3. Use the ▲ and ▼ buttons to select “RED”.
4. Adjust using the ◄ and ► buttons.
GREEN
BLUE
YELLOW
MAGENTA
CYAN
RESET
: OFF
EXIT
RETURN
SEL.
ADJ.
* If neither the ◄ or ► button is pressed within 5 seconds, the current selection is set and the previous screen
reappears.
To continue making other adjustments... Repeat from step 3.
5. Once the setting is completed...
Press the EXIT button to return to the main menu. To delete the main menu, press the EXIT button once more.
Information
■ COLOR CHART settings
RED ................... Makes red’s adjustment
GREEN ............. Makes green’s adjustment
BLUE ................ Makes blue’s adjustment
YELLOW .......... Makes yellow’s adjustment
MAGENTA ....... Makes magenta’s adjustment
CYAN ................ Makes cyan’s adjustment
RESET ............... Resets settings to the factory default values. Use and buttons to select “ON”, then press the MENU button.
■ Restoring the factory default settings
Select “FACTORY” under the INSTALL 1 menu. Note that this also restores other settings to the factory defaults.
27
Download from Www.Somanuals.com. All Manuals Search And Download.
OSD (On Screen Display) Controls
» AUDIO Menu
Adjusting the treble, bass and left/right balance and audio input select
The treble, bass and left/right balance can be adjusted to suit your tastes.
Example: Adjusting the bass
Press the MENU button on the remote control to display the MAIN MENU on the screen, then...
1. Use the and buttons to select “AUDIO”, then press the MENU button. The “AUDIO” screen appears.
2. To adjust the bass... Use the and buttons to select “BASS”.
3. Adjust the bass using the and buttons.
AUDIO
BASS
0
0
0
TREBLE
BALANCE
AUDIO INPUT1
AUDIO INPUT2
AUDIO INPUT3
:
:
:
VIDEO 1
HD/DVD 1
RGB 1
EXIT
SEL.
ADJ.
RETURN
To continue adjusting the audio ... Repeat from step 2.
Information
■ Audio setup menu
BASS .................... Controls the level of low frequency sound.
TREBLE ............... Controls the level of high frequency sound.
BALANCE ........... Controls the balance of the left and right channels.
■ Restoring the factory default settings
Select “FACTORY” under the INSTALL 1 menu.
Note that this also restores other settings to the factory defaults.
Note:
If “CAN NOT ADJUST” appears... Set “AUDIO INPUT” on the AUDIO menu correctly.
4. Once the adjustment is completed...
Press the EXIT button to return to the main menu. To delete the main menu, press the EXIT button once again.
28
Download from Www.Somanuals.com. All Manuals Search And Download.
OSD (On Screen Display) Controls
Setting the allocation of the audio connectors
Setting the AUDIO 1, 2, and 3 connectors to the desired input.
Example: Setting “AUDIO INPUT1” to “VIDEO1”
Press the MENU button on the remote control to display the MAIN MENU on the screen, then...
1. Use the and buttons to select “AUDIO”, then press the MENU button. The “AUDIO” screen appears.
2. Use the and buttons to select “AUDIO INPUT1”.
3. To set the AUDIO INPUT1 to “VIDEO1”...
Use the and buttons to select “VIDEO1”.
The mode switches as follows each time the and buttons is pressed:
The available sources depend on the setting of “BNC INPUT”.
RGB: → VIDEO1↔ VIDEO2 ↔ VIDEO3 ↔ HD1 ←
→ RGB3 ↔ RGB2 ↔ RGB1 ←
COMP: → VIDEO1↔ VIDEO2 ↔ VIDEO3 ↔ HD/DVD1 ←
→ RGB3 ↔ RGB1 ↔ HD/DVD2 ←
AUDIO
BASS
0
0
0
TREBLE
BALANCE
AUDIO INPUT1
AUDIO INPUT2
AUDIO INPUT3
:
:
:
VIDEO 1
HD/DVD 1
RGB 1
EXIT
SEL.
ADJ.
RETURN
4. Once the adjustment is completed...
Press the EXIT button to return to the main menu. To delete the main menu, press the EXIT button once more.
Information
■ AUDIO INPUT
A single audio input cannot be selected as the audio channel for more than one input terminal.
■ Restoring the factory default settings
Select “FACTORY” under the INSTALL 1 menu.
Note that this also restores other settings to the factory defaults.
29
Download from Www.Somanuals.com. All Manuals Search And Download.
OSD (On Screen Display) Controls
» IMAGE OPTIONS Menu
The position of the image can be adjusted and flickering of the image can be corrected.
Example: Adjusting the vertical position in the normal mode
Press the MENU button on the remote control to display the MAIN MENU on the screen, then...
1. Use the and buttons to select “IMAGE OPTIONS”, then press the MENU button. The “IMAGE OPTIONS”
screen appears.
Default settings (when RGB/PC is selected).
IMAGE OPTIONS
ASPECT RATIO
V SHIFT
:
VRTWIDE
0
0
0
0
H SHIFT
V-SIZE
H-SIZE
COMPUTER
FINE PICTURE
PICTURE ADJ
: OFF
0
0
EXIT
SEL.
ADJ.
RETURN
* The settings on the IMAGE OPTIONS menu are not preset at the factory.
To select a mode ...
Use the and buttons to select a mode. The mode switches as follows when the and buttons are pressed:
STD 4:3 ↔ ANAMPHC ↔ VRTWIDE ↔ LTR BOX
* The mode can also be switched by pressing the “ASPECT” button on the remote control.
2. To adjust the vertical position ...
Use the and buttons to select “V SHIFT”.
IMAGE OPTIONS
V SHIFT
0
ASPECT RATIO
V SHIFT
:
VRTWIDE
0
0
0
0
H SHIFT
V-SIZE
H-SIZE
EXIT
SEL.
ADJ.
RETURN
3. Adjust using the and buttons.
* If neither the
reappears.
or button is pressed within 5 seconds, the current setting is set and the previous screen
To continue making other computer image adjustments...
Repeat from step 2.
4. Once all adjustments are completed...
Press the EXIT button to return to the main menu, To delete the main menu, press the EXIT button once more.
30
Download from Www.Somanuals.com. All Manuals Search And Download.
OSD (On Screen Display) Controls
Information
■ When “COMPUTER” is off
IMAGE OPTIONS
ASPECT RATIO VRTWIDE
:
V SHIFT
0
0
0
0
H SHIFT
V-SIZE
H-SIZE
COMPUTER
FINE PICTURE
PICTURE ADJ
: OFF
0
0
EXIT
SEL.
ADJ.
RETURN
When Auto Picture is off, the Fine Picture and the Picture ADJ. items area displayed so that you can adjust them.
■ Adjusting the COMPUTER
ON .............. The picture ADJ., Fine Picture and Position adjustments are made automatically. Not available for digital ZOOM.
OFF ............ The Picture ADJ., Fine Picture and Position adjustments are made manually.
* If FINE PICTURE will not adjust, set “Computer” to OFF and adjust manually.
■ Adjusting the position of the image
V SHIFT................ Adjusts the vertical position of the image.
H SHIFT................ Adjusts the horizontal position of the image.
V-SIZE .................. Adjusts the vertical size of the image. (Except for VRTWIDE mode)
H-SIZE..................... Adjusts the horizontal size of the image. (Except for VRTWIDE mode)
FINE PICTURE* .... Adjusts for flickering.
PICTURE ADJ.* ..... Adjusts for striped patterns on the image.
*The Picture ADJ. and Fine Picture features are available only when the “Computer” is off.
* The COMPUTER, FINE PICTURE and PICTURE ADJ. are available only for RGB signals. But, these features are not available
for moving pictures on VIDEO, COMP or RGB.
■ Restoring the factory defaults settings
Select “FACTORY” under the INSTALL 1 menu. Note that this also restores other settings to the factory defaults for Auto Picture.
31
Download from Www.Somanuals.com. All Manuals Search And Download.
OSD (On Screen Display) Controls
» INSTALL 1 Menu
Setting the on-screen menu
This sets the position of the menu, the display format (horizontal or vertical) etc.
Example: Turning the DISPLAY OSD off
Press the MENU button on the remote control to display the MAIN MENU on the screen, then...
1. Use the and buttons to select “INSTALL 1”, then press the MENU button. The “INSTALL 1” menu
appears.
2. Use the and buttons to select “OSD”, then press the MENU button. The “OSD” menu appears.
3. Use the and buttons to select “DISPLAY OSD”.
4. To set the DISPLAY OSD to “OFF”...
Use the and buttons to select “OFF”. The mode switches as follows each time the or button is pressed:
ON ↔ OFF
OSD
DISPLAY OSD
OSD ADJ.
:
:
:
:
OFF
1
OSD ANGLE
OSD ORBITER
HOR.
OFF
EXIT
RETURN
SEL.
ADJ.
5. Once the setting is completed...
Press the EXIT button to return to the INSTALL 1 menu. To return to the main menu, press the EXIT button once
more.
Information
■ DISPLAY OSD settings
ON........ The on-screen menu appears.
■ OSD ORBITER settings
OFF ...... The on-screen menu does not appear.
If you press the DISPLAY button on the remote control for
more than 3 seconds the main menu will appear and can be set
(although it is not ON).
ON........ The position of the menu will be shifted
by eight dots each time OSD is displayed.
OFF ...... OSD will be displayed at the same position.
■ Restoring the factory defaults settings
Select “FACTORY” under the INSTALL 1 menu. Note that this
also restores other settings to the factory defaults for Auto
Picture.
■ OSD ADJUST settings
Adjusts the position of the menu when it appears on the screen.
The position can be set between 1 to 6.
1
4
2
5
3
6
■ OSD ANGLE settings
Sets the display format (landscape “HOR” or portrait “VERT”).
INSTALL 1
OSD
BNC INPUT
D-SUB TYPE
RGB TYPE
HD TYPE
:
:
:
:
:
:
COMP
RGB
AUTO
1080B
OFF
INPUT SKIP
FACTORY
OFF
NEXT PAGE
MENU/ENTER
EXIT
RETURN
SEL.
ENTER
32
Download from Www.Somanuals.com. All Manuals Search And Download.
OSD (On Screen Display) Controls
Setting the BNC connectors
Select whether to set the input of the 5 BNC connectors to RGB and Component.
Example: Set the BNC INPUT mode to “COMP”
Press the MENU button on the remote control to display the MAIN MENU on the screen, then...
1. Use the and buttons to select “INSTALL 1”, then press the MENU button. The “INSTALL 1” menu
appears.
2. Use the and buttons to select “BNC INPUT”.
3. To set the BNC INPUT mode to “COMP”...
Use the and buttons to select “COMP”. The mode switches as follows each time the or button is
pressed:
RGB ↔ COMP
4. Once the setting is completed...
Press the EXIT button to return to the main menu. To delete the main menu, press the EXIT button once more.
INSTALL 1
INSTALL 1
OSD
Information
OSD
BNC INPUT
D-SUB TYPE
RGB TYPE
HD TYPE
: COMP
: RGB
: AUTO
: 1080B
: OFF
BNC INPUT
D-SUB TYPE
RGB TYPE
HD TYPE
:
:
:
:
:
:
COMP
RGB
■ BNC INPUT settings
RGB ......... Use the 5BNC terminals for RGB input.
COMP ...... Use the 3BNC terminals for Component input.
AUTO
1080B
OFF
INPUT SKIP
FACTORY
: OFF
■ Restoring the factory default settings
Select “FACTORY” under the INSTALL 1 menu.
Note that this also restores other settings to the factory defaults.
INPUT SKIP
FACTORY
NEXT PAGE
OFF
MENU/ENTER
EXIT
RETURN
SEL.
ENTER
NEXT PAGE
EXIT
RETURN
SEL.
ADJ.
33
Download from Www.Somanuals.com. All Manuals Search And Download.
OSD (On Screen Display) Controls
Checking the signal being transmitted to RGB1 terminal
Use this to confirm the signal being transmitted to the RGB1 terminal. It is set to RGB and can not be adjusted.
INSTALL 1
OSD
BNC INPUT
D-SUB TYPE
RGB TYPE
HD TYPE
:
:
:
:
:
:
COMP
RGB
AUTO
1080B
OFF
INPUT SKIP
FACTORY
OFF
NEXT PAGE
EXIT
RETURN
SEL.
ADJ.
Setting a computer image to the correct RGB select screen
With the computer image, select the RGB Select mode for a moving image such as (video) mode, wide mode or
digital broadcast.
Example: Setting the “RGB TYPE” mode to “AUTO”
Press the MENU button on the remote control to display the MAIN MENU on the screen, then...
1. Use the and buttons to select “INSTALL 1”, then press the MENU button. The “INSTALL 1” menu
appears.
2. Use the and buttons to select “RGB TYPE”.
3. To set the RGB select mode to “AUTO”...
Use the and buttons to select “AUTO”. The mode switches as follows each time the or button is
pressed:
AUTO STILL MOTION RESIZE1 RESIZE2 DTV
INSTALL 1
OSD
BNC INPUT
D-SUB TYPE
RGB TYPE
HD TYPE
:
:
:
:
:
:
COMP
RGB
AUTO
1080B
OFF
INPUT SKIP
FACTORY
OFF
NEXT PAGE
EXIT
RETURN
SEL.
ADJ.
4. Once the setting is completed...
Press the EXIT button to return to the main menu. To delete the main menu, press the EXIT button once more.
34
Download from Www.Somanuals.com. All Manuals Search And Download.
OSD (On Screen Display) Controls
Information
■ RGB TYPE modes
One of these 6 modes must be selected in order to display the following signals correctly.
AUTO:
STILL:
Select the suitable mode for the specifications of input signals as listed in the table “Computer input signals supported
by this system” on page 61.
To display VESA standard signals. (Use this mode for a still image from a computer.)
MOTION: The video signal (from a scan converter) will be converted to RGB signals to make the picture more easily viewable.
(Use this mode for a motion image from a computer.)
RESIZE1: When an 852 dot 480 line signal with a horizontal frequency of 31.7kHz is input, the image may be compressed
horizontally. To prevent this, set RGB TYPE to RESIZE1.
RESIZE2: When an 848 dot 480 line signal with a horizontal frequency of 31.0 kHz is input, the image may be compressed
horizontally. To prevent this, set RGB TYPE to RESIZE2.
DTV:
Set this mode when watching digital broadcasting (480P).
■ Restoring the factory default settings
Select “FACTORY” under the INSTALL 1 menu. Note that this also restores other settings to the factory defaults.
Setting high definition images to the suitable screen size
Use this procedure to set whether the number of vertical lines of the input high definition image is 1035 or 1080.
Example Setting the “1080B” mode to “1035I”
Press the MENU button on the remote control to display the MAIN MENU on the screen, then...
1. Use the and buttons to select “INSTALL 1”, then press the MENU button. The “INSTALL 1” menu
appears.
2. Use the and buttons to select “HD TYPE”.
3. To set the HD TYPE mode to “1080B”...
Use the and buttons to select “1080B”.
The mode switches as follows each time the or button is pressed:
1080B 1035I 1080A
INSTALL 1
4. Once the setting is completed...
Press the EXIT button to return to the main menu.
To delete the main menu, press the EXIT button once more.
OSD
BNC INPUT
D-SUB TYPE
RGB TYPE
HD TYPE
:
:
:
:
:
:
COMP
RGB
AUTO
1080B
OFF
Information
INPUT SKIP
FACTORY
OFF
■ HD TYPE modes
These 3 modes are not displayed with correct image signals automatically.
NEXT PAGE
EXIT
RETURN
SEL.
ADJ.
1080B ......... Standard digital broadcasts
1035I ........... Japanese “High Vision” signal format
1080A ......... Special Digital broadcasts (for example: DTC100)
35
Download from Www.Somanuals.com. All Manuals Search And Download.
OSD (On Screen Display) Controls
Setting the Input Skip
When this is ON, signals which are not present will be skipped over and only pictures whose signals are being
transmitted will be displayed. This setting is valid only for the INPUT SELECT button on the unit.
Example: Set to “OFF”
Press the MENU button on the remote control to display the MAIN MENU on the screen, then...
1. Use the and buttons to select “INSTALL 1”, then press the MENU button. The “INSTALL 1” menu
appears.
2. Use the and buttons to select “INPUT SKIP”.
3. To set the INPUT SKIP mode to “OFF”...
Use the and buttons to select “OFF”. The mode switches as follows each time the or button is pressed:
INSTALL 1
OFF ON
OSD
BNC INPUT
D-SUB TYPE
RGB TYPE
HD TYPE
:
:
:
:
:
:
COMP
RGB
AUTO
1080B
OFF
INPUT SKIP
FACTORY
OFF
NEXT PAGE
EXIT
RETURN
SEL.
ADJ.
4. Once the setting is completed...
Press the EXIT button to return to the main menu. To delete the main menu, press the EXIT button once more.
Information
■ INPUT SKIP settings
OFF ........... Regardless of the presence of the signal, scan and display all signals.
ON.............. If no input signal is present, skip that signal.
* “SETTING NOW” will appear during the input search.
■ Restoring the factory default settings
Select “FACTORY” under the INSTALL 1 menu.
Note that this also restores other settings to the factory defaults.
36
Download from Www.Somanuals.com. All Manuals Search And Download.
OSD (On Screen Display) Controls
Resetting to the default values
Use these operations to restore all the settings (PICTURE ADJUST, AUDIO, IMAGE OPTIONS, INSTALL 1~3,
etc) to the factory default values.
1. On the MAIN MENU, select “INSTALL 1”, then press the MENU button.
The “INSTALL 1” menu appears.
2. Use the and buttons to select “FACTORY”, then press the
INSTALL 1
OSD
BNC INPUT
D-SUB TYPE
RGB TYPE
HD TYPE
:
:
:
:
:
:
COMP
RGB
AUTO
1080B
OFF
INPUT SKIP
FACTORY
OFF
NEXT PAGE
EXIT
RETURN
SEL.
ADJ.
3. Use the and buttons to select “ON”, then press the MENU button.
FACTORY
INSTALL 1
OSD
BNC INPUT
D-SUB TYPE
RGB TYPE
HD TYPE
:
:
:
:
:
:
COMP
RGB
SETTING NOW
AUTO
1080B
OFF
INPUT SKIP
FACTORY
NEXT PAGE
OFF
EXIT
RETURN
SEL.
ADJ.
When the “SETTING NOW” screen disappears, then all the settings are restored to the default values.
4. Once the setting is completed ...
Press the EXIT button to return to the main menu.
To delete the main menu, press the EXIT button once more.
37
Download from Www.Somanuals.com. All Manuals Search And Download.
OSD (On Screen Display) Controls
» INSTALL 2 Menu
Setting the Auto Off for computer images
This energy-saving (Auto Off) function automatically reduces the monitor’s power consumption if no operation
is performed for a certain amount of time.
Example: Turning the Auto Off function on
Perform the following operations.
Press the MENU button on the remote control to display the MAIN MENU on the screen, then...
1. Use the and buttons to select “INSTALL 2”, then press the MENU button. The “INSTALL 2” menu
appears.
2. Use the and buttons to select “AUTO OFF”.
3. To turn the Auto Off function on ...
Use the and buttons to select “ON”. The mode switches as follows each time the or button is pressed:
ON OFF
INSTALL 2
PREVIOUS PG
AUTO OFF
2 / 3
:
:
:
:
:
:
OFFf
ON
OFF
3
CINEMA MODE
PDP PROTECT
SIDEBAR ADJ
S1 / S2
OFF
ON
AUTO SIZE
DVI TYPE
NEXT PAGE
EXIT
RETURN
SEL.
ADJ.
4. Once the setting is completed...
Press the EXIT button to return to the main menu. To delete the main menu, press the EXIT button once more.
Information
■ AUTO OFF function
* The auto off function automatically reduces the monitor’s power consumption if the computer’s keyboard or mouse is not operated
for a certain amount of time. This function can be used when using the monitor with a computer.
* If the computer’s power is not turned on or if the computer and selector tuner are not properly connected, the system is set to the
off state.
* For instructions on using the computer’s Auto Off function, refer to the computer’s operating instructions.
■ AUTO OFF settings
ON ........ In this mode the Auto Off function is turned on. OFF ....... In this mode the Auto Off function is turned off.
■ AUTO OFF function and POWER / STANDBY indicator
The POWER/STANDBY indicator indicates the status of the Auto Off function. See page 39 for indicator status and description.
■ Restoring the factory default settings
Select “FACTORY” under the INSTALL 1 menu.
Note that this also restores other settings to the factory defaults.
38
Download from Www.Somanuals.com. All Manuals Search And Download.
OSD (On Screen Display) Controls
POWER / STANDBY indicator
AUTO
OFF
POWER /
STANDBY operating
AUTO OFF
Description
Turning the picture
back on
mode
indicator
status
On
Green
Not
Horizontal and
Picture already on.
activated.
vertical synchronizing
signals are present
from the computer.
Off
Red
Activated.
Horizontal and/or
Operate the keyboard
vertical synchronizing or mouse. The
signals are not sent
from the computer.
picture reappears.
Setting the picture to suit the movie
The film image is automatically discriminated and projected in an image mode suited to the picture. [NTSC, PAL, PAL60, 480I (60Hz),
525I (60Hz), 576I (50Hz), 625I (50Hz), 1035I (60Hz), 1080I (60Hz) only]
Example: Setting the “CINEMA MODE” to “OFF”
Perform the following operations.
Press the MENU button on the remote control to display the MAIN MENU on the screen, then...
1. Use the and buttons to select “INSTALL 2”, then press the MENU button. The “INSTALL 2” menu appears.
2. Use the and buttons to select “CINEMA MODE”.
3. To set the CINEMA MODE to “OFF”...
Use the and buttons to select “OFF”. The mode switches as follows each time the or button is pressed:
ON
OFF
INSTALL 2
PREVIOUS PG
AUTO OFF
2 / 3
:
:
:
:
:
:
OFFf
ON
OFF
3
CINEMA MODE
PDP PROTECT
SIDEBAR ADJ
S1 / S2
OFF
ON
AUTO SIZE
DVI TYPE
NEXT PAGE
EXIT
RETURN
SEL.
ADJ.
Information
■ CINEMA MODE
ON ......... Automatic discrimination of the image and projection
in cinema mode.
OFF ....... Cinema mode does not function.
■ Restoring the factory default settings
Select “FACTORY” under the INSTALL 1 menu.
Note that this also restores other settings to the factory defaults.
4. Once the setting is completed ...
Press the EXIT button to return to the main menu. To delete the
main menu, press the EXIT button once more.
39
Download from Www.Somanuals.com. All Manuals Search And Download.
OSD (On Screen Display) Controls
Plasma Display Panel Protection (PDP PROTECT)
Reducing burn-in of the screen
The brightness of the screen, the position of the picture, positive/negative mode and image sweep are adjusted to reduce burn-in of the
screen.
Perform the following operations.
Press the MENU button on the remote control to display the MAIN MENU on the screen, then...
1. Use the and buttons to select “INSTALL 2”, then press the MENU button. The “INSTALL 2” menu appears.
2. Use the and buttons to select “PDP PROTECT”, then press the MENU button. The “PDP PROTECT” screen appears.
PDP PROTECT
LUM. SETTING
ORBITER
:
AUTO
OFF
OFF
OFF
OFF
:
INVERSE
:
:
:
IMAGE SWEEP
SOFTEN
EXIT
RETURN
SEL.
ADJ.
3. Set the PDP PROTECT mode using
See page 40 to set LUM. SETTING
See page 41 to set ORBITER.
and buttons.
See page 42 to set INVERSE.
See page 43 to set IMAGE SWEEP.
Information
■ Restoring the factory default settings
Select “FACTORY” under the INSTALL 1 menu.
Note that this also restores other settings to the factory defaults.
4. Once the setting is completed...
Press the EXIT button to return to the INSTALL 2 screen.
To return to the main menu, press the EXIT button once more.
LUM. SETTING (Luminance Setting)
Use this to activate the brightness limiter.
Example: Setting “LUM. SETTING” to “SET. 1”
PDP PROTECT
LUM. SETTING
:
AUTO
ORBITER
:
OFF
OFF
OFF
OFF
Perform Steps 1-2 of PDP PROTECT, then...
INVERSE
:
:
:
3. Use the and buttons to select “LUM SETTING” (relates to above)
IMAGE SWEEP
SOFTEN
4. Use the and buttons to select “SET. 1”.
The mode switches as follows each time the or button is pressed:
EXIT
RETURN
SEL.
ADJ.
AUTO
SET. 1
SET. 2
SET. 3
Information
■ LUM. SETTING
AUTO ............ The brightness of the screen is adjusted automatically to suit the picture quality.
SET. 1, 2, 3 .... Sets maximum brightness. The brightness level decreases in the order of SET. 1, 2, 3.
SET. 3 provides minimum brightness.
40
Download from Www.Somanuals.com. All Manuals Search And Download.
OSD (On Screen Display) Controls
ORBITER
Use this to set the picture shift.
Example: Setting ”ORBITER” to “AUTO1”
PDP PROTECT
LUM. SETTING
:
AUTO
ORBITER
:
OFF
OFF
OFF
OFF
Perform Steps 1-2 of PDP PROTECT, then...
INVERSE
:
:
:
IMAGE SWEEP
SOFTEN
3. Use the and buttons to select “ORBITER”
(relates to above).
EXIT
RETURN
SEL.
ADJ.
4. Use the and buttons to select “AUTO1”.
The mode switches as follows each time the or button is pressed:
OFF AUTO1 AUTO2 MANUAL
Information
■ ORBITER settings
OFF ................ Orbiter mode does not function.
AUTO1............ The picture moves around the screen intermittently, making the picture smaller.
AUTO2 ........... The picture moves around the screen intermittently, making the picture bigger.
MANUAL ....... Use can adjust the orbiter function (H-Dot, V-Line and Time) manually. See the following explanation.
Adjust the ORBITER function manually.
Set the amount of shift and the time between movement.
Example: Setting so that the picture moves 2 dots horizontally and 3 lines vertically every 3 minutes.
Perform Steps 1-3 of ORBITER, then...
4. Use the and buttons to select “MANUAL”, then press the MENU button. The “ORBITER” screen
appears.
5. Adjust the items using the
pressed:
and buttons. The mode switches as follows each time the or button is
• H-DOT
Information
1 DOT 2 DOT ..... 19 DOT 20 DOT
■ ORBITER FUNCTION settings
H-DOT .......... Moves from 1 to 20 dots in the
horizontal direction.
• V-LINE
1 LINE 2 LINE ..... 19 LINE 20 LINE
V-LINE.......... Moves from 1 to 20 dots in the
vertical direction.
• TIME
1 M 2 M 3 M 4 M 5 M
TIME ............. Interval of 1~5 minutes.
ORBITER
H-DOT
V-LINE
TIME
:
:
:
2 DOT
4 LINE
3 M
EXIT
RETURN
SEL.
ADJ.
41
Download from Www.Somanuals.com. All Manuals Search And Download.
OSD (On Screen Display) Controls
INVERSE
Use this to set the inverse mode or to display a white screen.
Example: Setting “INVERSE” to “WHITE”
Perform Steps 1-2 of PDP PROTECT, then...
3. Use the and buttons to select “INVERSE”.
4. Use the and buttons to select “WHITE”. The mode switches as follows each time the or button is
pressed:
OFF ON WHITE
PDP PROTECT
LUM. SETTING
ORBITER
:
AUTO
OFF
OFF
OFF
OFF
:
INVERSE
:
:
:
IMAGE SWEEP
SOFTEN
EXIT
RETURN
SEL.
ADJ.
Setting the time for INVERSE
Set a time duration.
Example: Setting to that the INVERSE mode starts in 2 hours and proceeds for one hour and a half.
Perform Steps 1-3 of INVERSE, then...
4. Use the and buttons to select “ON”, then press the MENU button. The “INVERSE” screen appears.
5. Adjust the time using the
pressed:
and buttons. The mode switches as follows each time the or button is
INVERSE/WHITE
• ACTIVE
ON 00H03M 00H06M ...... 12H42M
12H45M
ACTIVE
:
01H30M
02H00M
STANDBY
:
• STANDBY
00H03M 00H06M 00H09M
.... 12H42M 12H45M
EXIT
RETURN
SEL.
ADJ.
6. Once the setting is completed...
Press the EXIT button to return to the PDP PROTECT screen.
Information
■ Setting the time
ACTIVE ............. Set the time duration for “INVERSE/WHITE”. When the ACTIVE is set to “ON” the mode will stay on.
STANDBY ......... Set the standby time until the “INVERSE/WHITE” mode starts.
* The “STANDBY” can not be set when the “ACTIVE” is ON.
* The “ACTIVE” and “STANDBY” can be set for up to 12 hours and 45 minutes in units of 3 minutes.
* When ending an ACTIVE function, the monitor will be in STAND BY.
[Example]
ACTIVE: 01H30M
STANDBY: 02H00M
|<---------- 2 H ---------->|<----- 1.5 H ----->|<----------
INVERSE/WHITE Start
STAND BY
■ To select “ON” for the “ACTIVE”...
Set the hours of the active time to 0H and the minutes to 0M.
“ON” will be displayed.
42
Download from Www.Somanuals.com. All Manuals Search And Download.
OSD (On Screen Display) Controls
IMAGE SWEEP
When this is set to ON, a white vertical bar moves repeatedly from the left and of the screen to the right end at a
constant speed.
Example: Setting “IMAGE SWEEP” to “ON”
Perform Steps 1-2 of PDP PROTECT, then...
3. Use the and buttons to select “IMAGE SWEEP”.
4. Use the and buttons to select “ON”. The mode switches as follows each time the or button is pressed:
OFF ON
PDP PROTECT
LUM. SETTING AUTO
Information
:
■ IMAGE SWEEP
ORBITER
:
OFF
OFF
OFF
OFF
ON ........ The white vertical bar appears.
You can set the time by pressing the MENU button while
“ON” is set.
INVERSE
:
:
:
IMAGE SWEEP
SOFTEN
OFF........ Image sweep mode does not funtion.
EXIT
RETURN
SEL.
ADJ.
Setting the time for IMAGE SWEEP
Set a time duration and the speed.
Example: Setting to that the IMAGE SWEEP mode starts
in 30 minutes and proceeds for one hour and a half.
Perform Steps 1-3 of IMAGE SWEEP, then...
4. Use the and buttons to select “ON”, then press the
MENU button. The “IMAGE SWEEP” screen appears.
5. Adjust the time using the
and buttons. The mode switches as follows each time the or button is
pressed:
• ACTIVE
ON 00H03M 00H06M ...... 12H42M
12H45M
IMAGE SWEEP
ACTIVE
STANDBY
SPEED
:
01H30M
• STANDBY
:
02H00M
1
00H03M 00H06M 00H09M ...... 12H42M 12H45M
:
• SPEED
EXIT
RETURN
SEL.
ADJ.
1
2
3
4
5
Information
■ Setting the time
ACTIVE ........ Set the time duration for “IMAGE SWEEP”. When the ACTIVE is set to “ON” the mode will stay on.
STANDBY .... Set the standby time until the “IMAGE SWEEP” mode starts.
SPEED ......... Set the moving speed for the “IMAGE SWEEP”. The speed decreases as the number increases.
* The “STANDBY” can not be set when the “ACTIVE” is ON.
* The “ACTIVE” and “STANDBY” can be set for up to 12 hours and 45 minutes in units of 3 minutes.
6. Once the setting is completed...
Press the EXIT button to return to the IMAGE SWEEP screen.
43
Download from Www.Somanuals.com. All Manuals Search And Download.
OSD (On Screen Display) Controls
SOFTEN
Reduces edges and softens the image.
Example: Setting “SOFTEN” to “2”
3. Use the and buttons to select “SOFTEN”.
4. Use the and button to select “2”. The mode switches as follows each time the or button is pressed:
1
2
3
4
5
Information
PDP PROTECT
LUM. SETTING
ORBITER
:
AUTO
OFF
OFF
OFF
OFF
■ SOFTEN settings
:
OFF ........ Turns the SOFTEN function off.
1,2,3,4 .....Activates the SOFTEN setting. The higher numbers
create a softer image.
INVERSE
:
:
:
IMAGE SWEEP
SOFTEN
“SHARPNESS” can not be adjusted on the “PICTURE
ADJUST” menu.
EXIT
SEL.
ADJ.
RETURN
Setting the SIDEBAR ADJ. for the sides of the screen
UsethisproceduretosettheSidebarAdj.forthepartsonthescreenonwhichnothingisdisplayedwhenthescreenissetto
4:3 size.
Example: Adjusting the “SIDEBAR ADJ”
Perform the following operations.
1. On the MAIN MENU, select “INSTALL 2”, then press the MENU button. The “INSTALL 2” menu appears.
2. Use the and buttons to select “SIDEBAR ADJ”.
3. To adjust the “SIDEBAR ADJ” ...
Use the and buttons to adjust the SIDEBAR ADJ
Information
■ SIDEBAR ADJ. settings
This adjusts the brightness of the black (the Sidebar Adj.) for the
sides of the screen. The standard is 0 (black). The level can be
adjusted from 0 to 15. The factory setting is 3 (dark gray).
■ Restoring the factory default settings
Select “FACTORY” under the INSTALL 1 menu.
Note that this also restores other settings to the factory defaults.
44
Download from Www.Somanuals.com. All Manuals Search And Download.
OSD (On Screen Display) Controls
Setting the screen size for S1/S2 video input
If the S-Video signal contains screen size information, the image will be automatically adjusted to fit the screen
when this S1/S2 is set to AUTO.
This feature is available only when an S-Video signal is input via the VIDEO3 terminal.
Example: Setting the “S1/S2” to “AUTO”
Perform the following operations.
1. On the MAIN MENU, select “INSTALL 2”, then press MENU button. The “INSTALL 2” screen appears.
2. Use the and buttons to select “S1/S2”.
3. Use the and buttons to select “AUTO”. The mode switches as follows each time the and buttons is
pressed:
INSTALL 2
PREVIOUS PG
AUTO OFF
2 / 3
OFF AUTO
Information
:
:
:
:
:
:
OFFf
ON
OFF
3
■ S1/S2 Settings
AUTO........ Adjusts the screen size automatically according to
the S1/S2 video signal.
CINEMA MODE
PDP PROTECT
SIDEBAR ADJ
S1 / S2
OFF
ON
OFF............ Turns the S1/S2 funtion off.
AUTO SIZE
DVI TYPE
■ Restoring the factory default settings
Select “FACTORY” under the INSTALL 1 menu. Note that this
also restores other settings to the factory defaults.
NEXT PAGE
EXIT
RETURN
SEL.
ADJ.
4. Once the setting is completed...
Press the EXIT button to return to the INSTALL 3 screen. To return to the main menu, press the EXIT button once
more.
Setting the signal and black level for DVI signal
Example: Setting the “PLUG/PLAY” mode on “STB/DVD”
Perform the following operations.
1. On the MAIN MENU, select “INSTALL 2”, then press the MENU button. The “INSTALL 2”
screen appears.
2. Use the and buttons to select “DVI TYPE”, then press the MENU button. The “DVI TYPE”
screen apprears.
3.To set PLUG/PLAY mode to “STB/DVD” ...
Use the and buttons to select “STB/DVD”.
The mode switches as follows each time the and buttons is pressed:
Information
■ PLUG/PLAY Settings
PC............... When connected to the PC
signal. BLACK LEVEL is set to “HIGH”
automatically. STB/DVD.... When connected
to a satellite receiver, DVD, etc. BLACK
LEVEL is set to “HIGH” automatically.
PLUG/PLAY:
BLACK LEVEL:
PC STB/DVD
LOW HIGH
DVI TYPE
PLUG/PLAY
:
:
STB/DVD
HIGH
■ BLACK LEVEL settings
LOW ........ When connected to the PC
signal.
BLACK LEVEL
HIGH ....... When connected to the satellite
receiver, DVD, etc. Change “HIGH” into
“OFF” if the black level apprears gray.
EXIT
RETURN
SEL.
ADJ.
45
Download from Www.Somanuals.com. All Manuals Search And Download.
OSD (On Screen Display) Controls
» INSTALL 3 Menu
Using the timer
This function sets the monitor to turn ON/OFF automatically at a set time.
Perform the following operations.
1. On the MAIN MENU, select “INSTALL 3”, then press MENU button. The “INSTALL 2” screen appears.
2. Use the and buttons to select “TIMER”, then press the MENU button. The “TIMER” screen apprears.
TIMER
Information
PRESENT TIME
■ Restoring the factory default settings
PROGRAM
:
OFF
Select “FACTORY” under the INSTALL 1 menu.
Note that this also restores other settings to the factory defaults.
MENU/ENTER
EXIT
RETURN
SEL.
ENTER
3. Set the TIMER using the
and buttons.
See below to set PRESENT TIME. See page 47 to set PROGRAM.
PRESENT TIME
This sets the day of the week and present time.
Example: Setting “WEDNESDAY”, “53:53”
Perform Steps 1-2 of TIMER, then...
3. Use the and buttons to select “PRESENT TIME”,
then press the MENU button. The “PRESENT TIME” screen appears.
TIMER
RETURN
DAYLITE TIME :
OFF
WEDNESDAY
00:53:53
MENU/ENTER
EXIT
RETURN
SEL.
ENTER
4. Use the and buttons to select the item, then adjust using the and buttons.
TIMER
RETURN
DAYLITE TIME :
OFF
WEDNESDAY
00:53:53
EXIT
SEL.
ADJ.
RETURN
46
Download from Www.Somanuals.com. All Manuals Search And Download.
OSD (On Screen Display) Controls
The mode switches as follows each time the or buttons is pressed:
• DAYLIGHT SAVING TIME
ON OFF
• DAY
SUNDAY MONDAY ...... FRIDAY SATURDAY
• HOUR/MINUTES
00:00 00:01 00:02 ..... 23:58 23:59
5. Once the setting is completed...
Use the and buttons to select “SET”, then press the MENU button. The adjustments are stored and return to
the TIMER menu.
Information
TIMER
RETURN
■ PRESENT TIME settings
DAYLIGHT SAVING TIME ....
DAYLITE TIME :
OFF
Use to set DAYLIGHT SAVING TIME.
ON: The present time + 1 hour.
OFF: Cancelled
WEDNESDAY
00:53:53
DAY ................ Set the day of the week (e.g. Sunday).
HOUR .............. Set the hour in the 24-hour format (range 00 to 23).
MINUTES ........ Set the minutes (range 00 to 59)
SET
SEL.
EXIT
ADJ.
RETURN
* If you press the EXIT button instead of the MENU button in step 5,
the settings can not be mode.
PROGRAM TIMER
This sets the day and time at which the power will be switched ON/OFF as well as the input mode.
Example:Settingsothatthepowerwillbeswitchedonat8:30A.M.,Monday,displayingRGB2source,andswitchedoffat
10:30 A.M.
Perform Steps 1-2 of TIMER, then...
3. Use the and buttons to select “PROGRAM”.
TIMER
PRESENT TIME
PROGRAM
:
ON
4. Use the and buttons to select “ON”, then press the MENU button.
The “PROGRAM TIMER” screen appears.
MENU/ENTER
EXIT
SEL.
ENTER
RETURN
5. Adjust using the
and buttons and ZOOM +/- button.
The mode switches as follows each time the ZOOM +/- button is pressed:
• DATE:
-- SUN MON .... SAT
*
SUN *MON
.... *SAT
TIMER
• ON/OFF Hour:
• MINUTE:
• INPUT:
00 01 02 .... 21 22 23
00 01 02 .... 57 58 59
DATE ON OFF INPUT FUNCTION
MON 8:30 10:30 RGB2
--- - -:- - - -:- - ---
--- - -:- - - -:- - ---
--- - -:- - - -:- - ---
--- - -:- - - -:- - ---
--- - -:- - - -:- - ---
--- - -:- - - -:- - ---
INVERSE
-----
-----
-----
-----
-----
-----
-- LAST VIDEO1 VIDEO2 VIDEO3 HD/DVD1
RGB3 RGB2 RGB1 HD/DVD2
ZOOM
EXIT
RETURN
SEL.
ADJ.
• FUNCTION: -- ORBITER INVERSE WHITE IMAGE SWEEP
6. Once the setting is completed... Press the EXIT button. The programs are stored, and return to the TIMER
screen.
47
Download from Www.Somanuals.com. All Manuals Search And Download.
OSD (On Screen Display) Controls
Information
■ PROGRAM TIMER settings
DATE ......................... Set the day of the week (e.g. Sunday).
TIMER
ON (hour, minutes) .... Set the time at which the power will be turned on in the 24-hour format.
OFF (hour, minutes)... Set the time at which the power will be turned off in the 24-hour format.
INPUT ....................... Set the input mode that will be displayed when the timer is on.
FUNCTION ........ Set the PDP PROTECT function.
DATE ON OFF INPUT FUNCTION
MON 8:30 10:30 RGB2
--- - -:- - - -:- - ---
--- - -:- - - -:- - ---
--- - -:- - - -:- - ---
--- - -:- - - -:- - ---
--- - -:- - - -:- - ---
--- - -:- - - -:- - ---
INVERSE
-----
-----
-----
-----
-----
-----
ZOOM
EXIT
RETURN
SEL.
ADJ.
■ To reset the program
Align the cursor with the DATE field that you wish to reset, then press the CLEAR button.
■ To reset the data
Align the cursor with the field (ON/OFF/INPUT/FUNCTION) that you wish to reset, then press the CLEAR button.
■ Special characters in the PROGRAM TIMER screen
Setting the DEFAULT INPUT
This function sets the input mode at the time the power is switched on.
Example: Setting “VIDEO2”
Perform the following operations.
Press the MENU button on the remote control to display the MAIN MENU on the screen, then ...
1. Use the and buttons to select “INSTALL 3”, then press the MENU button. The “INSTALL 3” screen
appears.
2. Use the and buttons to select “DEFAULT INPUT”.
3. To set the DEFAULT INPUT to “VIDEO2”... Use the and buttons to select “VIDEO2”.
• An asterisk “*” in the DATE field
An asterisk “*” means “every”. For example, “*FRI” means every Friday and “*” means everyday.
• A hyphen “-” in the ON field or OFF field
If any hyphen remains in the ON field of OFF field, the FUNCTION can not be set.
• A hyphen “-” in the FUNCTION field
A hyphen “-” means last mode (the mode that was last selected at the time the power was switched off).
The mode switches as follows each time the or buttons is pressed:
The available sources depend on the setting of “BNC INPUT”.
INSTALL 3
3 / 3
PREVIOUS PG
TIMER
INPUT SELECT
CONTROL LOCK : OFF
RGB: → LAST ↔ VIDEO1 ↔ VIDEO2 ↔ VIDEO3 ←
→ RGB3 ↔ RGB2 ↔ RGB1 ↔ HD1 ←
:
LAST
IR ENABLE
LOOP OUT
ID NUMBER
VIDEO WALL
:
:
:
ON
OFF
ALL
COMP: → LAST↔ VIDEO1 ↔ VIDEO2 ↔ VIDEO3 ←
→ RGB3 ↔ RGB1 ↔ HD2 ↔ HD1 ←
4. Once the setting is completed ...
Press the EXIT button to return to the main menu. To delete the
main menu, press the EXIT button once more.
48
Download from Www.Somanuals.com. All Manuals Search And Download.
OSD (On Screen Display) Controls
Information
■ INPUT SELECT settings
LAST ................... Last mode (the mode that was last selected at the time the power was switched off).
VIDEO 1, 2, 3 ...... VIDEO input mode.
RGB 1, 2, 3 .......... RGB input mode.
HD 1, 2 ................. HD/DVD input mode.
■ Restoring the factory default settings
Select “FACTORY” under the INSTALL 1 menu.
Note that this also restores other settings to the factory defaults.
Enabling/disabling the front panel controls
This function enables/disables the front panel controls.
Example: Setting “ON”
Perform the following operations.
Press the MENU button on the remote control to display the MAIN MENU on the screen, then...
1. Use the and buttons to select “INSTALL 3”, then press
the MENU button. The “INSTALL 3” screen appears.
INSTALL 3
PREVIOUS PG
TIMER
INPUT SELECT
CONTROL LOCK : OFF
3 / 3
:
LAST
2. Use the and buttons to select “CONTROL LOCK”.
IR ENABLE
LOOP OUT
ID NUMBER
VIDEO WALL
:
:
:
ON
3. To set the CONTROL LOCK to “ON”...
Use the and buttons to select “ON”, then press the MENU button.
The mode switches as follows each time the or button is pressed: OFF ON
OFF
ALL
EXIT
RETURN
SEL.
ADJ.
4. Once the setting is completed ...
Press the EXIT button to return to the main menu. To delete the main menu, press the EXIT button once more.
Information
■ CONTROL LOCK settings
ON ................... Disables the buttons on the front panel.
OFF .................. Enables the buttons on the front panel.
* Even when the CONTROL LOCK is set, the POWER switch will
not be locked.
* This becomes effective when the on-screen menu goes out.
49
Download from Www.Somanuals.com. All Manuals Search And Download.
OSD (On Screen Display) Controls
Enabling/disabling remote control wireless transmission
This function enables/disables remote control wireless transmission.
Example: Setting “OFF”
Perform the following operations.
Press the MENU button on the remote control to display the MAIN MENU on the screen, then...
1. Use the and buttons to select “INSTALL 3”, then press the MENU button. The “INSTALL 3” screen
appears.
INSTALL 3
PREVIOUS PG
TIMER
INPUT SELECT
CONTROL LOCK : OFF
3 / 3
2. Use the and buttons to select “IR ENABLE”.
:
LAST
IR ENABLE
LOOP OUT
ID NUMBER
VIDEO WALL
:
:
:
ON
3. To set the IR ENABLE to “OFF”...
Use the and buttons to select “OFF”, then press the MENU button.
The mode switches as follows each time the or button is pressed: OFF ON
OFF
ALL
EXIT
RETURN
SEL.
ADJ.
Information
4. Once the setting is completed ...
Press the EXIT button to return to the main menu.
To delete the main menu, press the EXIT button once more.
■ IR ENABLE settings
ON ........ Enables remote control wireless transmission.
OFF ....... Disables remote control wireless transmission.
Set “OFF” to avoid unwanted control from other remote
controls.
■ Restoring the factory default settings
Select “FACTORY” under the INSTALL 1 menu.
Note that this also restores other settings to the factory
defaults.
Loop Out Setting
When this feature is set to ON, the received signal will be looped out. Example: Setting “ON”
Perform the following operations. Press the MENU button on the remote control to display the MAIN MENU on
the screen, then...
1. Use the and buttons to select “INSTALL 3”, then press the MENU button. The “INSTALL 3” screen
appears.
INSTALL 3
PREVIOUS PG
TIMER
INPUT SELECT
CONTROL LOCK : OFF
3 / 3
2. Use the and buttons to select “LOOP OUT”.
:
LAST
IR ENABLE
LOOP OUT
ID NUMBER
VIDEO WALL
:
:
:
ON
OFF
ALL
3. To set the LOOP OUT to “ON”... Use the and buttons to select “ON”.
The mode switches as follows each time the or button is pressed: OFF ON
EXIT
RETURN
SEL.
ADJ.
Information
■ LOOP OUT settings
ON ........ The received signal will be looped out via PC1 terminal or VIDEO1 terminal.
OFF ....... The received signal will not loop out.
* Even if LOOP OUT is ON, signals would not be sent out if POWER is being turned off.
■ To connect to another display, refer to Loop Out Setting
■ If the RGB/PC1 signal is present at the time the power is switched on...
The RGB/PC1 input will be displayed regardless of the setting of LOOP OUT.
■ Restoring the factory default settings
Select “FACTORY” under the INSTALL 1 menu. Note that this also restores other settings to the factory defaults.
50
Download from Www.Somanuals.com. All Manuals Search And Download.
OSD (On Screen Display) Controls
ID Number Setting
When using more than one of these displays, this function sets ID numbers so that operation of the remote control
does not cause multiple monitors to operate at the same time.
Example: Setting “2”
Perform the following operations.
Press the MENU button on the remote control to display the MAIN MENU on the screen, then...
1. Use the and buttons to select “INSTALL 3”, then press the MENU button. The “INSTALL 3” screen
appears.
2. Use the and buttons to select “ID NUMBER”.
3. To set the ID NUMBER to “O2”...
Use the and buttons to select “2”.
The mode switches as follows each time the and button is pressed:
ALL
1
2
.... 255 256
Information
INSTALL 3
3 / 3
■ ID NUMBER settings
PREVIOUS PG
ALL ............. ID NUMBER will not be set.
1 to 256 ........ ID NUMBER will be set.
TIMER
INPUT SELECT
CONTROL LOCK : OFF
:
LAST
IR ENABLE
LOOP OUT
ID NUMBER
VIDEO WALL
:
:
:
ON
■ When the ID NUMBER has been set
OFF
ALL
You can also set ID NUMBER for each remote control to operate
the plasma display individually. To do so, requires special remote
control available only from Runco factory Service Department.
EXIT
RETURN
SEL.
ADJ.
■ Restoring the factory default settings
Select “FACTORY” under the INSTALL 1 menu.
Note that this also restores other settings to the factory defaults.
* To reset back to ALL, press the CLEAR button.
To set the ID number for the remote control
(requires special remote control available only from Runco factory Service Department)
Example: Setting “2”
1. Use the and buttons to select “ID NUMBER”.
2. To set the ID NUMBER to “2” ...
Use the and buttons to select “2”. The mode switches as follows each time the and button is pressed:
ALL
1
2
.... 255 256
SELECT ID
POSITION1:
1
ID NUMBER
:
ALL
EXIT
ADJ.
RETURN
* To reset back to ALL, press the CLEAR button.
4. Once the setting is completed... Press the EXIT button to delete the SELECT ID screen.
51
Download from Www.Somanuals.com. All Manuals Search And Download.
OSD (On Screen Display) Controls
Video Wall Setting
Use this feature to configure a 2×2 or 3×3 video wall.
Perform the following operations.
Press the MENU button on the remote control to display the MAIN MENU on the screen, then...
1. Use the and buttons to select “INSTALL 3”, then press the MENU button. The “INSTALL 3” screen
appears.
2. Use the and buttons to select “VIDEO WALL”, then press the MENU button. The “VIDEO WALL” screen
appears.
VIDEO WALL
DIVIDER
:
OFF
POSITION
DISP. MODE
AUTO ID
:
SPLIT
IMAGE OPT
P. ON DELAY
LUM SET LINK
REPEAT TIME
:
OFF
OFF
OFF
:
:
EXIT
RETURN
SEL.
ADJ.
3. Set the VIDEO WALL using
See page 53 to set DIVIDER.
and buttons.
See page 53 to set POSITION.
See page 54 to set DISP. MODE.
See page 54 to set AUTO ID.
See page 55 to set IMAGE ADJUST.
See page 55 to set P. ON DELAY.
See page 56 to set LUM SET LINK.
See page 57 to set REPEAT TIME.
4. Once the setting is completed...
Press the EXIT button to return to the INSTALL 3 menu.
5. Press the EXIT button to return to the main menu. To delete the main menu, press the EXIT button once
more.
NOTE:
A contingency method of shutting off the electric power should be used in cases of emergency during video wall
setup.
Information
■ Restoring the factory default settings
Select “FACTORY” under the INSTALL 1 menu.
Note that this also restores other settings to the factory defaults.
52
Download from Www.Somanuals.com. All Manuals Search And Download.
OSD (On Screen Display) Controls
DIVIDER
Set the 2x2 or 3x3 video wall.
Example: Setting “4”
Perform Steps 1-2 of VIDEO WALL, then...
3. Use the and buttons to select “DIVIDER”.
4. Use the and buttons to select “4”.
The mode switches as follows each time the or button is pressed:
OFF
1
4
9
VIDEO WALL
OFF
DIVIDER
:
Information
POSITION
DISP. MODE
AUTO ID
:
SPLIT
■ DIVIDER settings
OFF, 1 ......... 1 Screen (Matrix display function does not work)
4 .................. 4 Screens (2x2 video wall)
IMAGE OPT
P. ON DELAY
LUM SET LINK
REPEAT TIME
:
OFF
OFF
OFF
9 .................. 9 Screens (3x3 video wall)
* When you select “4” or “9”, set the VIDEO WALL POSITION.
:
:
EXIT
RETURN
SEL.
ADJ.
POSITION
Set the position of each display.
Example: Setting “4”
Perform Steps 1-2 of VIDEO WALL, then...
3. Use the and buttons to select “POSITION”, then press the MENU button. The “VIDEO WALL POSITION”
screen appears.
4. Use the and buttons to select “NO. 4”.
The mode switches as follows each time the or button is pressed:
• 4 Screens
NO. 1 NO. 2 NO. 3 NO. 4
Information
• 9 Screens
■ VIDEO WALL POSITION settings
1 Screen ..... There is no need to set POSITION.
4 Screens
NO. 7 NO. 8 ....... NO. 14 NO. 15
NO. 1
NO. 4
NO. 2
NO. 3
VIDEO WALL POSITION
POSITION NO.
:
4
9 Screens
NO. 7
NO. 8
NO. 9
NO. 10 NO. 11 NO. 12
NO. 13 NO. 14 NO. 15
EXIT
RETURN
SEL.
ADJ.
5. Press the EXIT button to return to the VIDEO WALL screen.
53
Download from Www.Somanuals.com. All Manuals Search And Download.
OSD (On Screen Display) Controls
DISP. MODE
Select the screen mode from between two options
(Splitting, Blanking).
Example: Setting “BLANK”
Perform Steps 1-2 of VIDEO WALL, then...
3. Use the and buttons to select “DISP. MODE”.
4. Use the and buttons to select “BLANK”.
The mode switches as follows each time the or button is pressed: SPLIT
BLANK
VIDEO WALL
Information
DIVIDER
:
OFF
POSITION
■ DISP. MODE SETTINGS
DISP. MODE
AUTO ID
:
SPLIT
SPLIT .......... Combines enlarged screens and creates
multiple
IMAGE OPT
P. ON DELAY
LUM SET LINK
REPEAT TIME
screens.
:
OFF
OFF
OFF
:
:
BLANK ....... Corrects misalignment of combined screen
portions and creates multiple screens.
EXIT
RETURN
SEL.
ADJ.
AUTO ID
This feature automatically sets the ID numbers of multiple displays connected to each other.
Example: Setting “ON”
Set the ID number for the No. 1 display on ID NUMBER menu.
Perform Steps 1-2 of VIDEO WALL, then...
3. Use the and buttons to select “AUTO ID”.
4. Use the and buttons to select “ON”, then press the MENU button.
The mode switches as follows each time the or button is pressed: OFF
ON
AUTO ID
Information
AUTO ID
:
ON
2
■ AUTO ID settings
ON ...... Enables Audo ID function. In the case shown below, display 1
will be set as ID 1, display 2 as ID 2, etc.
1
4
2
3
1
3
4
5
8
9
6
REMOTE
OUT
7
No. 1 No. 2
No. 4 No. 3
No. 1 No. 2
No. 4 No. 3
REMOTE
IN
REMOTE
OUT
WIRED CABLE
REMOTE
IN
CONNECTION TURN
EXIT
Display 1
Display 2
ADJ.
EXIT
REMOTE
OUT
No. 1 No. 2
No. 4 No. 3
No. 1 No. 2
No. 4 No. 3
REMOTE
OUT
REMOTE
IN
REMOTE
IN
Display 4
Display 3
OFF ..... Disables Auto ID function.
54
Download from Www.Somanuals.com. All Manuals Search And Download.
OSD (On Screen Display) Controls
IMAGE ADJUST
The position of the image can be adjusted and flickering of the image can be corrected.
Example: Adjusting the vertical position.
Perform Steps 1-2 of VIDEO WALL, then...
3. Use the and buttons to select “IMAGE OPT”, then press the MENU button. The “IMAGE OPT” screen
appears.
4. Use the and buttons to select “V SHIFT”.
IMAGE OPTIONS
ASPECT RATIO
V SHIFT
:
VRTWIDE
0
0
0
0
H SHIFT
V-SIZE
H-SIZE
EXIT
SEL.
ADJ.
RETURN
5. Adjust using the and buttons.
V SHIFT
0
* If neither the and button is pressed within 5 seconds, the current setting is set and the previous screen
reappears.
Information
6. Once the setting is completed...
■ IMAGE OPT settings
Press the EXIT button to return to the VIDEO WALL screen.
These are the same functions as the
IMAGE OPT menu.
P. ON DELAY (Power on delay)
Use this funciton to activate power-on delay.
Turn on the AUTO ID before the following operations.
Example: Setting “ON”
Perform Steps 1-2 of VIDEO WALL, then...
Information
3. Use the and buttons to select “P. ON DELAY”.
■ P. ON DELAY settings
ON ....... Turns on the main power of each display after a delay
time.
4. Use the and buttons to select “ON”.
The mode switches as follows each time the or
OFF ..... Turns on the main power of all displays at the same
time.
button is pressed: OFF
ON
VIDEO WALL
* Once this function has been set to “ON”, POWER ON/OFF
button on the remote control does not function except for the No.
1 monitor. By pressing the POWER ON button on the remote
control the No. 1 monitor will turn on and the others will be
turned on one by one automatically.
DIVIDER
:
OFF
POSITION
DISP. MODE
AUTO ID
:
SPLIT
IMAGE OPT
P. ON DELAY
LUM SET LINK
REPEAT TIME
:
OFF
OFF
OFF
* From the second monitor onward, neither the POWER button
on the unit nor the POWER ON button on the remote control does
function. However, by pressing and holding the POWER ON
button for more than 3 seconds, the monitor will be turned on.
:
:
EXIT
RETURN
SEL.
ADJ.
55
Download from Www.Somanuals.com. All Manuals Search And Download.
OSD (On Screen Display) Controls
LUM SET LINK
Use this function to set a uniform brightness for each display.
Turn on the AUTO ID before the following operations.
Example: Setting “ON”
Perform Steps 1-2 of VIDEO WALL, then...
3. Use the and buttons to select “LUM SET LINK”.
4. Use the and buttons to select “ON”, then press the MENU button.
The mode switches as follows each time the or button is pressed: OFF
ON
VIDEO WALL
DIVIDER
:
OFF
POSITION
DISP. MODE
AUTO ID
:
SPLIT
IMAGE OPT
P. ON DELAY
LUM SET LINK
REPEAT TIME
:
OFF
OFF
OFF
:
:
EXIT
RETURN
SEL.
ADJ.
Information
■ LUM SET LINK settings
ON ...... Sets a uniform brightness for each screen in a 2x2 video wall.
OFF .... Sets the individual screen brightness for each screen in a 2x2 video wall.
* Set “OFF” in a 3x3 video wall.
* When this function is set “ON”, connect your plasma displays with the remote cable (optional) in the
order of the position numbers for the 2x2 video wall. See the drawing below.
* If there are changes in the DIVIDER or POSITION, the LUM SET LINK will automatically turn OFF.
REMOTE
OUT
No. 1 No. 2
No. 4 No. 3
No. 1 No. 2
No. 4 No. 3
REMOTE
IN
REMOTE
OUT
REMOTE
IN
Display 1
Display 2
REMOTE
OUT
No. 1 No. 2
No. 4 No. 3
No. 1 No. 2
No. 4 No. 3
REMOTE
OUT
REMOTE
IN
REMOTE
IN
Display 4
Display 3
NOTE:
The remote control can not be operated unless the IR ENABLE is set to “OFF”.
56
Download from Www.Somanuals.com. All Manuals Search And Download.
OSD (On Screen Display) Controls
REPEAT TIME (REPEAT)
Use this to set two timers. Each timer can use the DIVIDER, SOURCE and ACTIVE functions.
Turn on the AUTO ID before the following operations.
Example:
TIMER1... VIDEO1 will be displayed for 3 minutes.
TIMER2... RGB1 will be displayed for 6 minutes in a 2×2 video wall.
Perform Steps 1-2 of VIDEO WALL, then...
3. Use the and buttons to select “REPEAT TIME”.
VIDEO WALL
DIVIDER
:
OFF
POSITION
DISP. MODE
AUTO ID
:
SPLIT
IMAGE OPT
P. ON DELAY
LUM SET LINK
REPEAT TIME
:
OFF
OFF
OFF
:
:
EXIT
RETURN
SEL.
ADJ.
4. Use the and buttons to select “ON”, then press the MENU button. The “REPEAT TIME” screen appears.
5. Adjust using the
and buttons.
The mode switches as follows each time the or button is pressed:
REPEAT TIME
Information
1 DIVIDER
SOURCE
ACTIVE
:
:
:
:
:
:
1
RGB1
00H03M
4
■ REPEAT TIME settings
If you set both timers, Timer 1 and Timer 2 run consecutively.
In the case of the Video Wall, timer No. 1 can be used to control
all the displays simultaneously.
2 DIVIDER
SOURCE
ACTIVE
RGB1
00H06M
* This becomes effective when the on-screen menu goes out.
EXIT
RETURN
SEL.
ADJ.
• DIVIDER
1
4
9
• SOURCE
The available sources depend on the setting of “BNC INPUT”.
→RGB: → VIDEO1 ↔ VIDEO2 ↔ VIDEO3 ↔ HD/DVD ←
→ RGB3 ↔ RGB2 ↔ RGB1 ↔ HD/DVD2 ←
• ACTIVE
00H01M 00H02M 00H03M .... 04H14M 04H15M
6. Once the setting is completed...
Press the EXIT button to return to the VIDEO WALL screen.
■ Restoring the factory default settings
Select “FACTORY” under the INSTALL 1 menu.
Note that this also restores other settings to the factory defaults.
57
Download from Www.Somanuals.com. All Manuals Search And Download.
OSD (On Screen Display) Controls
» LANGUAGE Menu
Setting the language for the menus
The menu display can be set to one of seven languages: English, German, French, Italian, or Spanish.
Example: Setting the menu display to “DEUTSCH”
Press the MENU button on the remote control to display the MAIN MENU on the screen, then...
1. Use the and buttons to select “LANGUAGE”, then press the MENU button. The “LANGUAGE” screen
appears.
2. To select “DEUTSCH”...
Use the and buttons to select “DEUTSCH”.
The mode switches as follows each time the and buttons
are pressed:
→ ENGLISH ↔ DEUTSCH ↔ FRANÇAIS ←
→ ITALIANO ↔ ESPAÑOL ←
LANGUAGE
LANGUAGE
:
ENGLISH
MENU/ENTER
EXIT
RETURN
ADJ.
ENTER
3. Once the setting is completed...
Press the MENU button to store the setting and return to the main menu. To delete the main menu, press the EXIT
button.
Information
■ Language settings
English
German
French
Spanish
Italian
58
Download from Www.Somanuals.com. All Manuals Search And Download.
OSD (On Screen Display) Controls
» COLOR SYSTEM Menu
Setting the video signal format
Use these operations to set the video standards of composite video signals or Y/C input signals.
Example: Setting the color system to “3.58 NTSC”
Press the MENU button on the remote control to display the MAIN MENU on the screen, then...
1. Use the and buttons to select “COLOR SYSTEM”, then press the MENU button.
The “COLOR SYSTEM” screen appears.
2. To select “3.58NTSC”...
Use the and buttons to select “3.58NTSC”.
The mode switches as follows when the and buttons are pressed:
→ AUTO ↔ 3.58NTSC ↔ 4.43NTSC ←
→ SECAM ↔ PAL-M ↔ PAL-N ↔ PAL-60 ↔ PAL ←
COLOR SYSTEM
COLOR SYSTEM
:
AUTO
EXIT
RETURN
SEL.
OK
3. Once the setting is completed...
Press the EXIT button to return to the main menu. To delete the main menu, press the EXIT button.
Information
■ Color System formats
Different countries use different formats for video signals. Set to the color system used in your current country.
AUTO ........... The color systems are automatically identified and the format is set accordingly.
PAL ............... This is the standard format used mainly in the United Kingdom and Germany.
SECAM ........ This is the standard format used mainly in France and Russia.
4.43 NTSC,
PAL60 ........... This format is used for videos in countries using PAL and SECAM video signals.
3.58 NTSC .... This is the standard format used mainly in the United States and Japan.
PAL-M .......... This is the standard format used mainly in Brazil.
PAL-N ........... This is the standard format used mainly in Argentina.
59
Download from Www.Somanuals.com. All Manuals Search And Download.
OSD (On Screen Display) Controls
» SIGNAL INFO. Menu
Checking the frequencies, polarities of input signals, and resolution
Use this function to check the frequencies and polarities of the signals currently being input from a computer,
etc.
Press the MENU button on the remote control to display the MAIN MENU on the screen, then...
1. Use the and buttons to select “SIGNAL INFO.”, then press the MENU button.
2. The “SIGNAL INFO” is displayed.
SIGNAL INFO
H. FREQ
V. FREQ
: 48.4KHz
: 60.0Hz
H. POLARITY
V. POLARITY
: NEG.
: POS.
MODE
: 480i
RESOLUTION
:
--
EXIT
RETURN
SEL.
OK
3. Once you have checked the frequency ...
Press the EXIT button to return to the main menu. To delete the main menu, press the EXIT button once more.
60
Download from Www.Somanuals.com. All Manuals Search And Download.
TABLE OF SIGNALS SUPPORTED
• When the screen mode is STD 4:3, each signal is converted to a 640 dots x 480 lines signal. (Except for *2, *4)
• When the screen mode is ANAMPHC, each signal is converted to a 853 dots x 480 lines signal. (Except for *3)
Computer input signals supported by this system
Vertical Horizontal
Sync Polarity
Presence
Screen Mode
RGB
Select *5
Mem-
ory
Model
Freq.
(Hz)
Freq.
(kHz)
Dots x Lines
DVI
Horizontal
Vertical
Horizon-
Vertical
Normal
Full
(16:9)
[ Signal Type ]
(4:3)
tal
640 x 400
640 x 480
70.1
59.9
72.8
75.0
85.0
100.4
120.4
60.0
60.0
56.3
60.3
72.2
75.0
85.1
99.8
120.0
60.0
70.1
75.0
85.0
100.6
31.5
31.5
37.9
37.5
43.3
51.1
61.3
31.0
31.7
35.2
37.9
48.1
46.9
53.7
63.0
75.7
48.4
56.5
60.0
68.7
80.5
NEG
NEG
NEG
NEG
NEG
NEG
NEG
POS
NEG
POS
POS
POS
POS
POS
POS
POS
NEG
NEG
POS
POS
NEG
NEG
NEG
NEG
NEG
NEG
NEG
NEG
POS
NEG
POS
POS
POS
POS
POS
POS
POS
NEG
NEG
POS
POS
NEG
YES
YES
YES
YES
YES
YES
YES
YES
YES
YES
YES
YES
YES
YES
YES
YES
YES
YES
YES
YES
YES
YES
YES
YES
YES
YES
YES
YES
YES
YES
YES
YES
YES
YES
YES
YES
YES
YES
YES
YES
YES
YES
YES*2*3
YES*3
YES*3
YES*3
YES*3
YES*3
YES*3
--
YES
YES
YES
YES
YES
YES
YES
YES*3
YES*3
YES
YES
YES
YES
YES
YES
YES
YES
YES
YES
YES
YES
--
NO
4
STILL
YES
YES
YES
YES
YES
YES
YES
YES
YES
YES
YES
YES
YES
YES
YES
YES
YES
YES
YES
NO
5
--
7
STILL
8
--
9
--
41
42
19
17
11
12
13
14
15
43
44
24
25
26
27
45
--
WIDE2
WIDE1
STILL
STILL
--
*IBM PC/AT
Compatible
Computers
848 X 480
852 X 480*1
800 X 600
--
YES
YES
YES
YES
YES
YES
YES
YES
YES
YES
YES
YES
--
--
--
--
1024 X 768
STILL
--
STILL
--
--
Vertical Horizontal
Sync Polarity
Presence
Horizontal Vertical
Screen Mode
RGB
Select*5
Mem-
ory
Model
Freq.
(Hz)
Freq.
(kHz)
Dots x Lines
DVI
Horizontal
Vertical
Normal
(4:3)
Full
(16:9)
[ Signal Type ]
1152 X 864
1280 X 768
75.0
56.2
59.8
60.0
60.0
59.9
60.0
75.0
85.0
100.1
60.0
65.0
70.0
75.0
85.0
66.7
74.6
74.9
75.1
60.0
71.2
72.0
66.0
76.0
76.1
67.5
45.1
48.0
47.7
47.7
48.3
64.0
80.0
91.1
108.5
75.0
81.3
87.5
93.8
106.3
35.0
49.7
60.2
68.7
64.6
75.1
78.1
61.8
71.7
81.1
POS
POS
POS
POS
POS
NEG
POS
POS
POS
POS
POS
POS
POS
POS
POS
POS
POS
NEG
POS
POS
POS
POS
POS
POS
POS
POS
POS
POS
POS
POS
YES
YES
YES
YES
YES
YES
YES
YES
YES
YES
YES
YES
YES
YES
YES
--
YES
YES
YES
YES
YES
YES
YES
YES
YES
YES
YES
YES
YES
YES
YES
--
YES
--
YES
YES
YES
YES
YES
YES
YES
YES
YES
YES
YES
YES
YES
YES
YES
YES
YES
YES
YES
YES
YES
YES
YES
YES
YES
STILL
YES
NO
YES
NO
YES
YES
YES
NO
NO
NO
NO
NO
NO
NO
NO
NO
NO
NO
NO
YES
NO
NO
NO
NO
NO
51
52
80
22
22
53
29
30
40
47
54
55
56
57
58
6
WIDE1
--
WIDE3
1360 X 765
1360 X 768
1376 X 768
1280 X 1024
--
WIDE1
--
WIDE1
--
WIDE2
YES*4
YES*4
YES*4
YES*4
YES
YES
YES
YES
YES
YES*3
YES
YES
YES
YES*4
YES*4
YES*4
YES
YES
YES*4
STILL
--
--
--
1600 X 1200
--
--
--
--
--
640 X 480
832 X 624
Sync on G Sync on G
Sync on G Sync on G
Sync on G Sync on G
Sync on G Sync on G
--
*Apple
Macintosh*6
--
--
--
16
28
39
29
48
59
60
61
30
1024 X 768
1152 X 870
1280 X 1024
--
--
WIDE1
--
--
WIDE1
NEG
NEG
NEG
NEG
YES
YES
--
YES
YES
--
--
--
--
--
--
--
Work Station
(EWS4800)
Work Station (HP)
1280 X 1024
1152 X 900
--
--
Work Station
(Sun)
C Sync
C Sync
C Sync
C Sync
C Sync
C Sync
--
--
--
--
1280 X 1024
--
--
61
Download from Www.Somanuals.com. All Manuals Search And Download.
Table of Signals Supported (continued)
Vertical Horizontal
Sync Polarity
Presence
Screen Mode
RGB
Select*5
Mem-
ory
Model
Freq.
(Hz)
Freq.
(kHz)
Dots x Lines
DVI
Horizontal
Vertical
Horizontal Vertical
Normal
Full
(16:9)
[ Signal Type ]
(4:3)
1024 X 768
60.0
60.0
49.7
63.9
--
--
--
--
--
--
--
--
YES
YES*4
YES
YES
--
--
YES
YES
62
29
Work Station
(Sun)
1280 X 1024
IDC-3000G
PAL625P
768 X 576
640 X 480
50.0
59.9
31.4
31.5
NEG
NEG
NEG
NEG
YES
YES
YES
YES
YES*7
YES*7
YES*7
YES*7
--
NO
NO
31
32
NTSC525P
MOTION
*1 Only when using a graphic accelerator board that is capable of displaying 852 x 480.
*2 Display only 400 lines with the screen center of the vertical orientation located at the center.
*3 The picture is displayed in the original resolution. The picture will be compressed for other signals.
*4 Aspect ratio is 5:4. This signal is converted to the following signal: 600 dots x 480 lines).
*5 Normally the RGB select mode suite for the input signals is set automatically. If the picture is not displayed
properly, set the RGB mode prepared for the input signals listed in the table above.
*6 To connect the monitor to a Macintosh computer, use the monitor adapter (D-Sub 15-pin) to your computer’s
video port.
*7 Other screen modes (LTR BOX and VRTWIDE) are available as well.
NOTE:
• While the input signals comply with the resolution listed in the table above, you may have to adjust the position
and size of the picture or the fine picture because of errors in synchronization of your computer.
• This monitor has a resolution of 853 dots x 480 lines. It is recommended that the input signal be VGA, wide VGA
or equivalent.
• With digital input some signals are not accepted.
• The sync may be disturbed when a nonstandard signal other than the aforementioned is input.
• If you are connecting a composite sync signal, use the HD terminal.
* “IBM PC/AT” and “VGA” are registered trademarks of International Business Machines, Inc. of the United
States.
* “Apple Macintosh” is a registered trademark of Apple Computer, Inc. of the United States.
62
Download from Www.Somanuals.com. All Manuals Search And Download.
TROUBLESHOOTING
If the picture quality is poor or there is some other problems, check the adjustments, operations, etc., before re-
questing service.
SYMPTOM
CHECKS
REMEDY
Picture is disturbed.
Sound is noisy.
• Is a connected component set directly in front or at the side of the
display?
• Leave some space between the display and the connected
components.
Remote control operates erroneously.
The remote control does not work.
• Are the remote control’s batteries worn out?
• Is IR ENABLE set to ON?
• Replace both batteries with new ones.
• Set IR ENABLE OFF on INSTALL 3 menu.
• Has an ID number been set for the main unit?
• Set an ID number with the SELECT ID button, or set the ID
number to ALL.
Monitor’s power does not turn on when • Is the monitor’s power cord plugged into a power outlet?
• Plug the monitor’s power cord into a power outlet.
• Press the power button on the monitor to turn on the power.
• Replace both batteries with new ones.
the remote control’s power button is
pressed.
• Are all the monitor’s indicators off?
• Are the remote control’s batteries worn out?
• Is IR ENABLE set to ON?
• Set IR ENABLE OFF.
• Has an ID number been set for the main unit.
• Set an ID number with the SELECT ID button, or set the ID
number to ALL.
Monitor does not operate when the
remote control’s buttons are pressed.
• Is the remote control pointed at the monitor, or is there an obstacle • Point the remote control at the monitor’s remote control sensor
between the remote control and the monitor?
when pressing buttons, or remove the obstacle.
• Is direct sunlight or strong artificial light shining on the monitor’s
remote control sensor?
• Eliminate the light by closing curtains, pointing the light in a
different direction, etc.
• Are the remote control’s batteries worn out?
• Replace both batteries with new ones.
• Unplug the remote cable from the monitor.
• Set the Control Lock to OFF.
The front panel buttons of the main unit • The front panel buttons do not function during Control Lock.
do not function.
No sound or picture is produced.
• Is the monitor’s power cord plugged into a power outlet?
• Is the volume set at the minimum?
• Plug the monitor’s power cord into a power outlet.
• Increase the volume.
Picture appears but no sound is
produced.
• Is the mute mode set?
• Are the speakers properly connected?
• Press the remote control’s MUTE button.
• Connect the speakers properly.
• Is AUDIO set correctly?
• Set AUDIO on the AUDIO menu correctly.
Poor picture with VIDEO signal input.
Poor picture with RGB signal input.
• Improper control setting. Local interference. Cable
interconnections. Input impedance is not correct level.
• Adjust picture control as needed. Try another location for the
monitor. Be sure all connections are secure.
• Improper control setting. Incorrect 15 PIN connector pin
connections.
• Adjust picture controls as needed. Check pin assignments and
connections.
Tint is poor or colors are weak.
Nothing appears on screen.
• Are the tint and colors properly adjusted?
• Is the computer’s power turned on?
• Is a source connected?
• Adjust the tint and color (under PICTURE ADJUST).
• Turn on the computer’s power.
• Connect source to the monitor.
• Is the Auto Off function in the standby or off mode?
• Is LOOP OUT set to ON?
• Operate the computer (move the mouse, etc.)
• Set LOOP OUT OFF.
Part of picture is cut off or picture is not • Is the position adjustment appropriate?
centered.
• Adjust the IMAGE OPTIONS properly.
Image is too large or too small.
• Is the screen size adjustment appropriate?
• Press the ASPECT button on the remote control and adjust
properly.
Picture is unstable.
• Is the computer’s resolution setting appropriate?
• Set to the proper resolution.
• Check the input signal.
POWER/STANDBY indicator is lighted
in red.
• Horizontal and / or vertical sync signal is not present when the
Auto Off control is on.
POWER/STANDBY indicator is blinking • The temperature inside the main unit has become too high and has • Promptly switch off the power of the main unit and wait until the
in red.
activated the monitor.
internal temperature drops. See *1.
POWER/STANDBY indicator is blinking
in green and red, or green.
• Promptly switch off the power of the main unit. See *2.
----------
*1 Overheat Protector
If the monitor becomes too hot, the overheat protector will be activated and the monitor will be turned off. If this happens, turn off the power to the
monitor and unplug the power cord. If the room where the monitor is installed is particularly hot, move the monitor to a cooler location and wait for
the monitor to cool for 60 minutes. If the problem persists, contact your Runco Authorized Dealer.
*2 In the following case, power off the monitor immediately and contact your Runco Authorized Dealer or Runco Authorized Service Center. The
monitor turns off 5 seconds after powering on and then the POWER/STANDBY indicator blinks. It indicates that the power supply circuit, plasma
display panel or temperature sensor have been damaged.
63
Download from Www.Somanuals.com. All Manuals Search And Download.
DIMENSIONS
3.875
25.625
42" diagonal
41.250
64
Download from Www.Somanuals.com. All Manuals Search And Download.
SPECIFICATIONS
Native Resolution:
Screen Size:
853 x 480
42 in. (diagonal)
Screen Aspect Ratio:
Available Aspect Ratios:
16:9
4:3, Letterbox, 16:9 Anamorphic, VirtualWide™
Image Area (W x H):
36 1/3 in. (921 mm) x
20 7/16 in. (518 mm)
DTV Compatibility:
Contrast Ratio:
480p, 720p, 1080i
1000:1
Data/Graphics Capability:
Inputs:
640 x 400 to 1600 x 1200
(2) Composite Video (1-BNC, 1-RCA), (1) S-Video, (2) Component Video (1-BNC, 1-RCA), (1)
RGB (15-pin mini D-sub), (1) RGB via BNC, (1) DVI w/HDCP, (1) RS-232C, (3) Stereo RCA jacks
Power Requirements:
120V AC, 50/60 Hz
Power Consumption:
270W
Operating Environments:
32˚ - 104˚F (0˚ - 40˚C), 20-80% Humidity (non-condensing)
Dimensions
Width: 41 1/4 in. (1048 mm)
Depth: 3 7/8 in. (98.43 mm)
Height: 25 5/8 in. (651 mm)
Weight: 67.5 lbs. (30.62 kg)
Regulatory Approvals:
Limited Warranty:
FCC, CE, C-Tick
(3) Three years parts and labor (not including the plasma glass panel) from the date of delivery to the
end user.
(1) One year parts and labor on the plasma glass panel from the date of delivery to the end user.
65
Download from Www.Somanuals.com. All Manuals Search And Download.
Download from Www.Somanuals.com. All Manuals Search And Download.
Download from Www.Somanuals.com. All Manuals Search And Download.
RUMA-010400
01-17-06 v2.0
Runco International
2900 Faber Street
Union City, CA 94587
Ph (510) 324-7777 / Fax (510) 324-9300
1-800-23RUNCO
Download from Www.Somanuals.com. All Manuals Search And Download.
|