Royal Sovereign Laminator RSC 1400C User Guide

17. WARRANTY  
Royal Sovereign International warrants the equipment sold is free from defects in  
material and workmanship for a period of One (1) year for Parts and Labor from the date  
of installation, excluding lamination rollers which are warranted for Six (6) months. This  
warranty is extended only to the original purchaser. This warranty is the only warranty  
made by Royal Sovereign International and cannot be modified or amended. Royal  
Sovereign’s sole and exclusive liability and the customer’s sole and exclusive remedy  
under this warranty shall be, at Royal Sovereign’s option, to repair or replace any such  
defective part or product. These remedies are only available if Royal Sovereign’s  
examination of the product discloses to Royal Sovereign’s satisfaction that such defects  
actually exist and were not caused by misuse, neglect, attempt to repair, unauthorized  
alternation or modification, incorrect line voltage, fire, accident, flood or other hazard.  
OWNER'S MANUAL  
RSC-1400C/1400H Laminators  
The warranty made herein is in lieu of all other warranties, expressed or implied,  
including any warranty or merchantability or fitness for a particular purpose. Royal  
Sovereign will not be liable for personal damage or personal injury (unless primarily  
caused by its negligence), loss of profit, or other incidental or consequential damages  
arising out of the use or inability to use this equipment.  
LIMITED WARRANTY  
This warranty specifically does not cover damage to laminating rollers caused by knives,  
razor blades, or any sharp objects or abrasives, or failure caused by adhesives, or  
damage caused by lifting, tilting and/or any attempt to position the machine other than  
rolling on the installed castors or feet on even surfaces, or improper use of the  
machine. Warranty repair or replacement by Royal Sovereign or its authorized  
Reseller(s) does not extend the warranty beyond the initial one year period from the  
date of installation. Unauthorized customer alterations will void this warranty.  
CORPORATE HEADQUARTERS  
Royal Sovereign International Inc.  
2 Volvo Drive, Rockleigh, NJ 07647 U.S.A.  
TEL : +1) 800-397-1025  
FAX : +1) 201-750-1022  
E-mail : [email protected]  
RS Holland B.V.  
Columbusstraat 25 - 3165 AC Rotterdam,  
The Netherlands  
E-mail : [email protected]  
Royal Sovereign Inc. <Oversea Sales Office>  
1001, World Meridian II, 426-5, Gasan-dong,  
Geumcheon-gu, Seoul, 153-759, KOREA  
TEL : +82)2-2025-8800 FAX : +82)2-2025-8830  
E-mail : [email protected]  
Read all instructions carefully before use.  
For any Customer Support needs please choose the  
Customer Support tab on www.royalsovereign.com  
RS International Australia PTY. LTD.  
30 Prime Drive, Seven Hills, NSW 2147, Australia  
TEL : +61) 2-9674-2127  
RS Canada Inc.  
164 Oakdale Road, Toronto, Ontario M3N 2S5  
CANADA  
Royal Sovereign International Inc.  
FAX : +61) 2-9674-2027  
TEL : +1  
)
416-741-8400 FAX : +1 416-741-8185  
)
E-mail : [email protected]  
E-mail : [email protected]  
19  
Download from Www.Somanuals.com. All Manuals Search And Download.  
RSC-1400C/H  
4. INCLUDED WITH LAMINATOR  
3. INSTALLATION  
Thoroughly inspect the parts and the unit. It is imperative that any missing parts are  
reported and a claim is filed with the reseller immediately upon receipt of shipment.  
Note: The laminator should be installed by a trained service technician.  
The laminator comes fully assembled, except for the feed table and paper guide to avoid  
shipping damage. Upon arrival, thoroughly inspect the unit. It is imperative that any  
shipping damage is reported and a claim is filed with the delivering carrier immediately  
upon receipt.  
Quantity  
1
Picture  
Part Name  
Laminator  
The laminator should be located in an area with adequate work space for feeding graphics  
and lamination materials.  
Owner's Manual  
1
6/4  
1
Avoid placing the laminator in a dusty area or near sources of extreme heat or cold.  
3´´(76mm) / 2" (57mm) Auto Grip  
Once the laminator is in place, lock the casters into position(“ON” position). Always unlock  
the casters (“OFF” position) when moving to a different location.  
Registration Card  
L-wrench (2.5)  
Dust Cover  
1
ELECTRICAL REQUIREMENTS  
Royal Sovereign recommends that a licensed electrician ensures proper power installation  
to your laminator in accordance with electrical codes in your area.  
1
1
1
Spare Motor Fuse - FUSE(50T)  
(6.3A)  
The laminator should have a dedicated power line.  
MODEL  
RSC-1400C  
RSC-1400H  
Spare Main Power Fuse - FUSE(65TS)  
(5A)  
220-240V  
50/60HZ  
120V  
50/60HZ  
220-240V  
50/60HZ  
120V  
50/60HZ  
Power Supply  
8 - 1/4"Hexa head Bolt (M6 20mm)  
8 - Spring Washer( 6.1)  
single phase  
10/10  
12/12  
(Included with option only)  
12 - 3/16"screw (M5 10mm).  
12 - Spring Washer( 5.1)  
(Included with option only)  
Front Feeder and Rear Rewinder Kit  
(Included with option only)  
2/2  
4
120V UL  
230V UL  
240V UK  
4 - 1/3"Hexa head Bolt (M8 70mm)  
4 - Spring Washer( 8.5)  
(Included with option only)  
4 - 1/3"screw (M8 60mm).  
4 - Spring Washer( 8.5)  
(Included with option only)  
4
4
220V EU  
NUT M8)  
220V AU  
3
4
Download from Www.Somanuals.com. All Manuals Search And Download.  
RSC -1400C/H  
5. PRODUCT IDENTIFICATION  
6. CONTROL PANEL  
When the machine is initially turned on, the LED display window will show the speed and  
temperature set at 1. (RSC-1400C and RSC-1400H).  
12  
11  
2
1
3
4
10  
9
5
6
8
13  
7
RSC-1400H  
RSC-1400C  
Control Buttons  
NO.  
1
PART NAME  
RSC-1400C  
RSC-1400H  
SAFETY COVER  
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
1. TEMPERATURE DISPLAY: Display’s current temperature (RSC-1400C and RSC-1400H)  
2
EMERGENCY SWITCH  
FRAME-PAPER GUIDE  
FEED TABLE  
2. SPEED DISPLAY: Display’s current Speed.  
3
3. TEMPERATURE BUTTON- (RSC-1400C and RSC-1400H): To change the temperature  
4
(max. RSC-1400H: 122ºF, 50ºC ) of the upper roller, press up or down arrow button.  
5
MAIN ROLLER  
4. SPEED BUTTON: Adjusting the speed of the rollers. To change the speed of the rollers,  
6
ASSEMBLY STAND  
FOOT PEDAL  
press the up or down arrow button.  
7
8
TENSION CONTROL KNOBS  
PRESSURE LEVER  
CONTROL PANEL  
UPPER IDLE BAR  
5. RUN: To start the rollers.  
9
6. STOP: To stop the rollers.  
10  
11  
12  
13  
7. REV: To reverse the rollers, press and hold the REVERSE button.  
RELEASE LINER TAKE UP  
REMOTE CONTROL  
5
6
Download from Www.Somanuals.com. All Manuals Search And Download.  
RSC-1400C/H  
7. SPEED AND TEMPERATURE SETTINGS  
9. USING FOOT PEDAL AND REMOTE CONTROL  
USING FOOT PEDAL  
RSC-1400C/H  
Speed(Ft/min,M/min)  
4(1.2)  
RSC-1400H  
Temperature( F, C )  
No Heating  
No Heating  
91(33)  
Speed#  
Temp.#  
Place the foot pedal on the floor in front of the  
machine. Once all correct settings are displayed, you  
may use the foot pedal to operate the laminator for  
“Hands Free Operation.” To activate the machine,  
press the foot pedal once and then release. Repeat  
to stop the rollers.  
1
2
3
4
5
6
7
8
9
1
2
3
4
5
6
7
8
9
6(1.7)  
7(2.2)  
9(2.6)  
97(36)  
104(40)  
10(3.1)  
111(44)  
12(3.6)  
115(46)  
14(4.2)  
117(47)  
15(4.5)  
124(51)  
16(5.0)  
USING REMOTE CONTROL  
1
2
3
8. ROLLER NIP SETTING  
It is important to adjust the roller nip settings to the appropriate thickness of the board  
being used. Use the guide below to adjust to the correct position.  
Located on the rear left side of the laminator.  
1. PRESS RUN – To activate the rollers.  
2. PRESS STOP – To stop the rollers from turning.  
3. PRESS REV – To reverse the rollers. Press and  
hold the button (useful for jams or misted media).  
Metric  
NO.  
Inches  
(mm)  
Lamination  
1
1
2
3
4
5
Lamination  
1/ 25"  
3/16"~1/4"  
3/ 8"~1/2"  
3/5"  
5-7  
10-13  
15  
NOTE: If you don't want to  
laminate,please place the  
pressure lever to the "Open  
position(NO.5)".  
7
8
Download from Www.Somanuals.com. All Manuals Search And Download.  
RSC-1400C/H  
10. USING CROSS CUTTER  
11. LOADING FILM  
Royal Sovereign films are wound with the adhesive side facing the inside of the roll  
The cross cutter is located on the rear exit table of the machine.  
(adhesive in).  
Loading films to upper and lower film shafts:  
(See page 5 for assistance with parts identification.)  
1. After lamination, move the cutter approximately to  
the center of the completed application at the  
desired point of detachment (Figure 1).  
1. Adjust the auto grip to fit to the film and tighten the  
auto grip screw (Figure 1).  
Figure 1  
Figure 2  
Figure 3  
Figure 1  
2. Remove the upper and lower film shafts from the  
machine and load the films (Center the upper and  
lower films on the shaft). Note the direction of the  
adhesives on the lower and upper films  
(Figure 2).  
2. Grasp film with one hand, press the cutter  
downward into the application and slide it from  
one end to the other. (Figure 2 & 3).  
Figure 2  
3. Load the upper and lower film shafts on the  
machine (Figure 3).  
Figure 3  
9
10  
Download from Www.Somanuals.com. All Manuals Search And Download.  
RSC-1400C/H  
9. Cut and separate the release liner and the film.  
(Figure 3)  
12. THREADING FILM  
Figure 3  
10. Thread the craft paper behind the Lower Idle Bar to  
the top film that is resting on the main roller (do not  
use the Lower Idle Bar for Mounting). (Figure 4)  
12.1. Decaling  
11. Reinstall the Feed Table and the Frame-Paper  
Guide,and close the Safety Cover.  
1. Turn the power switch on (“I” position). The Power  
switch is located on the rear left side of the unit.  
Figure 4  
Figure 5  
Figure 6  
12. Adjust the nip setting to appropriate gap.  
2. Complete the steps as in the “LOADING FILM”  
section (see page 10).  
13. Insert and push the leader board until they reach the  
front nip point.  
3. Set the top roller to the desired temperature (RSC-  
1400C)  
14. Push the Run button.  
4. Take off the Frame-Paper Guide and the Feed Table.  
15. Push the leader board into the rollers. (Figure 5)  
5. Pull the top film down over the Safety Cover to the  
bottom of the craft paper / Mounting film.  
Figure 1  
16. Adjust the top and bottom tension knob by rotating it  
clockwise or counterclockwise. Turn it until the top  
and bottom roll films have some resistance varies  
(the tension depending on the film thickness; the  
thicker the film the more tension is required).  
(Figure 6)  
6. Align and center the craft paper / Mounting film to the  
top film and tighten the two lower core screws (Figure  
1).  
7. Thread the top film underneath the Upper Idle  
Bar.(Figure 2)  
8. Tape the top film on to the Release Liner Take-  
Up.(Figure 2)  
Figure 2  
11  
12  
Download from Www.Somanuals.com. All Manuals Search And Download.  
RSC-1400C/H  
17. Press the Stop button when the leader board has completely exited from the rollers.  
18. Use the Cross Cutter to cut the leader board from the web (see page 9).  
4. Flip the image over the top roller and hold on to the  
release liner (Figure 4).  
19. Set the nip setting to the appropriate position for the Over-lamination / Decaling  
application.  
Figure 4  
12.2. Mounting  
1. Lay the decaled image face down on a flat surface.  
Carefully peel back and put a crease along the  
edge of the release liner ( Approximately 1 in or  
25mm, Figure 1).  
5. Press the foot pedal once, and then let it go while  
slowly pulling the release liner as the board enters  
the main roller nip (Figure 5)  
Figure 5  
6. Press the foot pedal once again when the board  
has completely exited from the rear of the unit. Trim  
the board if necessary.  
Figure 1  
2. With the image facing up, align the image onto the  
board. Press firmly from the center out (Figure 2).  
Figure 2  
3. Adjust the pressure lever to ensure the proper  
opening (Figure 3).  
Figure 3  
13  
14  
Download from Www.Somanuals.com. All Manuals Search And Download.  
RSC-1400C/H  
4. Disassemble the power switch bracket and place the left  
rewinder outside of the frame; fasten with round head  
3/16"(M5) screws (included in the option kit). Then,  
reinstall the power switch bracket (Figure 7).  
13. INSTALLATION OF FRONT FEEDER and REAR  
REWINDER OPTIONS  
Note: Below options are to be installed by an authorized RS reseller.  
Figure 7  
Figure 8  
Figure 9  
Installation of the Front Feeder Option (Includes 2 brackets,  
one spindle, and mounting hardware).  
5. Install the right rewinder on the outside of the frame and  
connect the motor wire connector to the rear wire  
(Figures 8 & 9).  
1. Install the Front Feeder to the inside of the front frames  
using four 1/4"(M6) hexagon bolts on each side (Figure 1)  
Figure 1  
6. Reinstall the rear cover.  
Installing the Rear Rewinder Option (Includes motorized  
winder, bracket, one spindle, and mounting hardware).  
7. Reinstall the side covers.  
1. Remove the left and right covers by using a Phillips  
screwdriver (four screws on each side cover) (Figures 2 &  
8. Reinstall the lever knob and screw.  
Figure 2  
Figure 3  
3).  
2. Remove the lever knob screw and lever (Figure 4).  
Figure 4  
3. Remove the rear cover by removing all  
10 screws (4 top, 4 bottom, and 1 on  
each side) (Figure 5 & 6).  
Figure 5  
Figure 6  
15  
16  
Download from Www.Somanuals.com. All Manuals Search And Download.  
RSC -1400C/H  
14. MAINTENANCE  
16. SPECIFICATIONS  
Cleaning the Body of the laminaor  
1. To clean the machine body, dampen a cloth with water only and gently wipe the machine clean.  
Removing Adhesive Build Up  
1. Remove the film from the laminator.  
2. Use a damp (water only) cloth and a rubber gum eraser to remove the adhesive on the  
Teflon (metal) and silicone rollers.  
Note: Rub firmly but do not scrub the rollers vigorously as this may scratch the  
surface.Do not use sharp metal objects, steel wool, or abrasives, as these  
may also damage the rollers.  
Lubrication  
1. Drive chain and sprockets should be lubricated with either a light coat of gear lube or  
heavy grease (lithium grease) after 6 months or 1000 hours of operation, whichever  
comes first.  
15. TROUBLESHOOTING  
Problem  
Cause  
Solution  
a. Plug the power cord into appropriate  
outlet.  
b. Put the power switch to the “I” (On)  
position.  
a. Power plug is not plugged in.  
b. Power switch is in “0” (Off) position.  
c. Tripped circuit breaker.  
Machine will not turn  
on:  
d. Blown main power fuse.  
c. Reset the circuit breaker.  
d. Replace the fuse.  
a. Emergency switch (es) is (are)  
engaged.  
b. Paper guide is not installed correctly.  
There is power, but the  
rollers are not turning  
after the “RUN” button  
is pressed:  
a. Disengage the emergency switch (es).  
b. Properly install the paper guide so that  
the micro switch is activated.  
c. Replace the motor fuse.  
c. Blown motor fuse.  
The unit is not heating  
up:  
a. Did not raise the temperature.  
a. Raise the temperature.  
a. Upward curl.  
b. Downward curl.  
a. Loosen the top roll film tension.  
b. Loosen the bottom roll film tension.  
Curled lamination:  
17  
18  
Download from Www.Somanuals.com. All Manuals Search And Download.  

Roland Drums TD 20 User Guide
Rotel Stereo Amplifier RB 970BX User Guide
Salton Coffeemaker ME5B User Guide
Samsung Cell Phone DFX 5000 User Guide
Samsung Digital Camera EC WB30FZBPBUS User Guide
Samsung Telephone iDCS 500 User Guide
Sangean Electronics Clock Radio PR D2 V User Guide
Sanus Systems Indoor Furnishings EFSat User Guide
Sanyo Microwave Oven EM C8787V User Guide
Sears Snow Blower 24788557 User Guide