Rosewill Modem RC403 User Guide

PCI 56Kbps V.92 Data/fax Voice Modem Card  
RC403  
User Manual  
Download from Www.Somanuals.com. All Manuals Search And Download.  
PCI 56Kbps V.92 Data/fax Voice Modem Card RC403  
User Manual  
Installation Guide for Windows Series  
98/98SE/ME/2000 and XP  
System Requirements  
• Computer with Pentium 200 MMX or higher processor.  
• Windows 98/98SE/ME/2000 and XP Operating System.  
• 20 MB Hard Disk free space or above  
• Sound card for voice features  
• ꢀ available PCI slot.  
• CD-ROM drive.  
Modem Installation  
ꢀ. Please turn off your computer and disconnect the power cable.  
2. Please remove the cover from your computer. Please check your computer¡¦s manual for  
instructions and cautions regarding the removal of covers or installation of add-in boards.  
3. Please select an empty PCI slot and remove the appropriate expansion slot cover from the  
computer.  
4. Please insert the Internal 56k Modem into the PCI slot and secure with a screw in the  
backplane.  
5. Please replace the Computers cover.  
6. Please insert one end of the telephone cord into the Modem¡¦s Line (top) Socket  
7. Please connect the other end of the phone cord to a telephone phone point, via the supplied  
adaptor (RJꢀꢀ) if required.  
8. Please turn on your computer.  
9. As Windows 98FE/98SE/2000/ME/XP starts it will detect that new hardware has been added,  
and start the ¡§Add New Hardware Wizard¡¨ Click on Cancel.  
ꢀ0.Please insert the analog Modem communication CD into your CD-ROM drive.  
ꢀꢀ. The CD should auto-start, displaying the following window. If it does not start, click on Start  
- Run and type in CD:\autorun.exe (where CD is the drive letter of your CD-ROM drive.  
ꢀ2. Please select--Install Modem Driver. If you can not perform these procedures smoothly as  
above, please perform the file directly: CD:\Autorun.exe  
2
Download from Www.Somanuals.com. All Manuals Search And Download.  
PCI 56Kbps V.92 Data/fax Voice Modem Card RC403  
User Manual  
Basic AT Command Guide  
T - Set Tone Dial Default  
This command forces DTMF dialing until the next P dial modifier or P command is received. The  
modem will set an S-Parameter bit to indicate that all subsequent dialing should be conducted in  
tone mode. Note that the DP command will override this command. Clears Sꢀ4 bit 5.  
This command may not be permitted in some countries. (See P.)  
Syntax  
T
Result Codes  
OK  
P - Set Pulse Dial Default  
This command forces pulse dialing until the next T dial modifier or T command is received. Sets  
Sꢀ4 bit 5.  
As soon as a dial command is executed which explicitly specifies the dialing mode for that  
particular call (e.g., ATDT..), this command is overridden so that all future dialing will be tone  
dialed. (See T command.)  
This command may not be permitted in some countries.  
A - Answer The modem will go off-hook and will attempt to answer an incoming call if correct  
conditions are met. Upon successful completion of answer handshake, the modem will go on-line  
in answer mode. This command may be affected by the state of Line Current Sense, if enabled.  
(Most countries do not require Line Current Sense.) Operation is also dependent upon +FCLASS  
command and country-specific requirements. If +FCLASS=0 is selected, the modem will enter  
the connect state after exchanging carrier with the remote modem. If no carrier is detected within  
a period specified in register S7, the modem will hang up. Any character entered during the  
connect sequence will abort the connection attempt.  
If +FCLASS=ꢀ.0 is selected, the modem will go off-hook in V.2ꢀ answer mode. It will generate the  
V.2ꢀ 2ꢀ00 Hz answer tone for 3 0.5 seconds. Following a delay of 70 ms, it will proceed as if the  
+FTH=3 command were issued. At any stage up to (but excluding) the +FTH=3 command state,  
anycharacter will abort the communication. (See the description of the +FTH command for  
details.)  
H - Disconnect (Hang-Up)  
This command initiates a hang up sequence. This command may not be available for some  
countries  
due to PTT restrictions.  
Syntax  
H[<value>]  
Defined Values  
<value> Decimal number corresponding to the selected option.  
0
The modem will release the line if the modem is currently on-line.  
If on-hook, the modem will go off-hook and remain in command mode.  
3
Download from Www.Somanuals.com. All Manuals Search And Download.  
PCI 56Kbps V.92 Data/fax Voice Modem Card RC403  
User Manual  
Result Codes  
OK <value> = 0 or ꢀ.  
ERROR Otherwise.  
O - Return to On-Line Data Mode  
This command specifies that the modem will enter the on-line data mode from the on-line  
command mode with or without a retrain. If in the off-line command mode when this command  
is entered, the modem reports ERROR.  
Syntax  
O[<value>]  
Defined Values  
<value> Decimal number corresponding to the selected option.  
0
Enters on-line data mode from the on-line command mode without a retrain. Handling is  
determined by the Call Establishment task. Generally, if a connection exists, this command  
connects the DTE back to the remote modem after an escape (+++).  
Performs a retrain then enters on-line data mode from the on-line command mode.  
Result Codes  
OK <value> = 0 or ꢀ and a connection exists.  
ERROR Otherwise or no connection exists  
L - Speaker Volume  
This command sets the speaker volume control according to the parameter supplied.  
Syntax  
L[<value>]  
Defined Values  
<value> Decimal number corresponding to the selected option.  
0
2
3
Low speaker volume.  
Low speaker volume. (Default.)  
Medium speaker volume.  
High speaker volume.  
Result Codes  
OK <value> = 0 to 3.  
ERROR Otherwise.  
M - Speaker Control  
This command controls speaker on or off according to the supplied parameter.  
Syntax  
M[<value>]  
Defined Values  
<value> Decimal number corresponding to the selected option.  
0
2
3
Speaker off.  
Speaker on during call establishment, but off when receiving carrier. (Default.)  
Speaker on.  
Speaker is off when receiving carrier and during dialing, but on during answering.  
Result Codes  
OK <value> = 0 to 3.  
ERROR Otherwise.  
4
Download from Www.Somanuals.com. All Manuals Search And Download.  
PCI 56Kbps V.92 Data/fax Voice Modem Card RC403  
User Manual  
&V - Display Current Configuration and Stored Profile  
This command reports the current (active) configuration and the stored (user) profiles.  
Syntax  
&V  
Result Code  
OK  
Example:  
AT&V  
ACTIVE PROFILE:  
Eꢀ Lꢀ Mꢀ Q0 T Vꢀ X0 &Cꢀ &D2 &G0 &T0  
S00:000 S0ꢀ:000 S02:043 S03:0ꢀ3 S04:0ꢀ0 S05:008 S06:004  
S07:050 S08:004  
Sꢀ0:0ꢀ4 Sꢀ2:050 Sꢀ6:000 Sꢀ8:000 S29:070  
STORED PROFILE 0:  
Eꢀ Lꢀ Mꢀ Q0 T Vꢀ X4 &Cꢀ &D2 &G0 &T0  
S00:000 S02:043 S06:004 S07:050 S08:004 Sꢀ0:0ꢀ4 Sꢀ2:050  
Sꢀ8:000 S29:070  
OK  
&W - Store Current Configuration  
This command saves the current (active) configuration (profile), including S-Parameters, in the  
Registry. The current configuration is comprised of a list of storable parameters illustrated in the  
&V  
command. These settings are restored to the active configuration upon receiving an Z command  
or at power up.  
Syntax  
&W  
Result Code  
OK  
*B - Display Blacklisted Numbers  
This command requests the modem to return a list of blacklisted numbers to the DTE. The format  
of  
the response is shown by the example below. Permanently forbidden numbers as defined by  
country  
requirements will not appear on this list. If no numbers are blacklisted, only the OK result code is  
issued. Example: NO. - PHONE NUMBER -  
------ ------------------------------  
ꢀ; 4ꢀ75537660  
2; 828892496ꢀ  
3; 3887278862  
4; 3ꢀ24839442  
5; 6284664  
OK  
*D - Display Delayed Numbers  
This command causes the modem to send a list of the delayed numbers together with the delay  
associated with each. The modem will return a list of delayed telephone numbers as defined in  
5
Download from Www.Somanuals.com. All Manuals Search And Download.  
PCI 56Kbps V.92 Data/fax Voice Modem Card RC403  
User Manual  
the *B command. The format of the response is shown by the example below (delay times are  
shown as hours:minutes:seconds). If no numbers are delayed, only the OK result code is issued.  
Example:  
NO. - PHONE NUMBER -DELAY  
------ -------------------------------------------  
ꢀ; 8264734660 2:00:00  
2; 753263466ꢀ 2:00:00  
3; 2587334662 0:02:00  
4; 753265ꢀ663 0:03:25  
5; 745993ꢀ664 0:0ꢀ:45  
OK  
V.92 +P and –Q Commands  
This section describes the +P (PCM DCE) and –Q commands and parameters used to control the  
V.92 Mode operation.  
+PCW - Call Waiting Enable  
This command controls the operation of the modem in the presence of call waiting.  
Syntax  
+PCW=<value>  
Defined Values  
<value> Decimal number corresponding to the selected operation.  
0
Request modem-on-hold if enabled by +PMH and collect caller ID information if enabled by  
+VRID. Toggle V.24 circuit ꢀ25. (Default.)  
Hang-up.  
2
Ignore call waiting.  
Result Codes  
OK <value> = 0, ꢀ, or 2.  
ERROR Otherwise.  
Reporting Selected Value(s)  
Command: +PCW?  
Response: +PCW: <value>  
Example: +PCW: 0 For the default setting.  
Reporting Supported Range of Parameter Values  
Command: +PCW=?  
Response: +PCW: (<value> range)  
Example: +PCW: (0,ꢀ,2)  
+PMH - Modem-on-Hold Enable  
This command controls the selection of modem-on-hold in the modem. The action of the modem  
in response to modem-on-hold events is determined by the state of this command as well as the  
6
Download from Www.Somanuals.com. All Manuals Search And Download.  
PCI 56Kbps V.92 Data/fax Voice Modem Card RC403  
User Manual  
state of a negotiated handshake with a V.92-compliant server in V.92 Mode.  
Syntax  
+PMH=<value>  
Defined Values  
<value> Decimal number corresponding to the selected operation.  
0 Modem-on-hold enabled in V.92 Mode. (Default.)  
ꢀ Disabled modem-on-hold.  
Result Codes  
OK 0 or ꢀ in V.92 Mode  
ERROR Otherwise.  
Reporting Current or Selected Value  
Command: +PMH?  
Response: +PMH: <current value>  
Example: +PMH: 0 For the default setting.  
Reporting Supported Range of Parameter Values  
Command: +PMH=?  
Response: +PMH: (<value> range)  
Example: +PMH: (0,ꢀ)  
+PMHT – Modem-on-Hold Timer  
This command controls whether or not the modem will grant or deny a modem-on-hold (MOH)  
request as well as setting the MOH Timeout value.  
Syntax  
+PMHT=<value>  
Defined Values  
<value> Decimal number corresponding to selected setting.  
0
Deny V.92 modem-on-hold Request (Default.)  
Grant MOH with ꢀ0 second timeout  
Grant MOH with 20 second timeout  
Grant MOH with 30 second timeout  
Grant MOH with 40 second timeout  
Grant MOH with ꢀ minute timeout  
Grant MOH with 2 minute timeout  
Grant MOH with 3 minute timeout  
Grant MOH with 4 minute timeout  
Grant MOH with 6 minute timeout  
Grant MOH with 8 minute timeout  
Grant MOH with ꢀ2 minute timeout  
Grant MOH with ꢀ6 minute timeout  
2
3
4
5
6
7
8
9
ꢀ0  
ꢀꢀ  
ꢀ2  
7
Download from Www.Somanuals.com. All Manuals Search And Download.  
PCI 56Kbps V.92 Data/fax Voice Modem Card RC403  
ꢀ3 Grant MOH with indefinite timeout  
User Manual  
Result Codes  
OK 0-ꢀ3 in V.92 Mode (+MS=V92)  
ERROR Otherwise  
Reporting Current or Selected Values  
Command: +PMHT?  
Response: +PMHT: <value>  
Example: +PMHT: 0 For the default setting.  
Reporting Supported Range of Parameter Values  
Command: +PMHT=?  
Response: +PMHT: (<value> range)  
Example: +PMHT: (0,ꢀ,2,3,4,5,6,7,8,9,ꢀ0,ꢀꢀ,ꢀ2,ꢀ3)  
support.  
If you have any question while using our products, please feel free to contact us at  
8
Download from Www.Somanuals.com. All Manuals Search And Download.  

RCA CD Player RP 9300 User Guide
RCA Portable Radio 35873 User Guide
RF Link Technology Stereo Amplifier APW 1000 User Guide
Rowe Headphones UM10032 User Guide
Royal Sovereign Laminator 1050 User Guide
RTS Stereo Amplifier RVON 8 User Guide
Samsung All in One Printer SF 330 User Guide
Sears Pressure Washer 58076101 User Guide
Seiko Watch V072 User Guide
Senco Air Compressor PC0968 User Guide