Rosen Entertainment Systems Car Video System UN7000 User Guide

RO SEN  
UN7000  
7” Universal  
Headrest  
Monitor  
Rosen Entertainment Systems  
1120 California Avenue Corona CA 92881  
(909) 898-9808  
9000514  
Owner’s Manual  
and Installation Guide  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Installation  
Flush Mounting  
Table of Contents  
The kit includes a protective trim ring and an optional spacer ring for  
use when the mounting surface is uneven.  
1. Select appropriate locations in your vehicle for the monitor  
and for the power supply module.  
Introduction and System Overview ................................................4  
Operating Guide ..............................................................................5  
Remote Control ..................................................................................5  
Front Panel Controls ..........................................................................6  
Turning On and Off the Monitor ..........................................................7  
Changing Video Inputs.......................................................................7  
Dimming the Backlight .......................................................................8  
Adjusting the Color, Brightness, and Tint ............................................8  
Image Formats ...................................................................................9  
ResetAll Settings .............................................................................10  
Installation ...................................................................................... 11  
Box Contents.................................................................................... 11  
Electrical Installation ........................................................................12  
Physical Mounting............................................................................13  
Pedestal Mounting .................................................................................. 13  
Flush Mounting ....................................................................................... 14  
2. Be sure there is sufficient depth for the trim ring. Add the  
spacer ring for shallow locations with uneven curved surfaces  
such as upholstery. Be sure there is enough space for both  
the trim ring and for any excess interconnect cable.  
3. Ensure that the interconnect cable will reach from the monitor  
location to the power supply module.  
4. Create the required opening for the monitor and trim ring. Be  
sure it is not too large, and that there is enough space behind  
the trim ring to store any excess interconnect cable. Excess  
cable does not fit within the trim ring.  
5. Route the cable through the opening in the trim ring:  
Trim Ring  
Cable  
6. Mount the trim ring with the screws provided.  
7. Connect the cable to the monitor.  
8. Securely snap the monitor into place.  
Trim Ring  
Monitor  
If you need to remove the monitor from the trim ring, insert the tool  
provided between the monitor and the trim ring to release the monitor  
from the flexible locking retainer tabs. Gently pull the monitor from the  
trim ring. Very gentle pressure can be applied using the tool provided  
or a credit card.  
UN7000 7” Widescreen Universal Monitor  
Page 14  
UN7000 7” Widescreen Universal Monitor  
Page 3  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Introduction and System Overview  
Installation  
Physical Mounting  
Introduction and System Overview  
Congratulations on your purchase of a Rosen Widescreen Universal  
Monitor! This widescreen flat panel LCD monitor features advanced  
display technology and versatile installation options.  
Two mounting options are available - pedestal mounting or flush  
mounting.  
Pedestal Mounting  
To install the pedestal mount:  
Your Rosen Widescreen Universal Monitor includes the following  
features:  
1. Select appropriate locations in your vehicle for the pedestal  
and for the power supply module.  
16:9 aspect ratio. Sometimes called “widescreen,” this is the  
same aspect ratio used by next generation digital  
televisions.  
2. Test fit the mounting pedestal foot in the desired location:  
Be sure that the monitor will be able to slide onto the  
pedestal without interference.  
7" screen (measured diagonally).  
Be sure that the mounting location can accommodate  
screws safely. Never screw into any surface without first  
inspecting behind and below it.  
Adjustable backlight to compensate for ambient lighting  
conditions.  
Normal, Zoom, and Full screen formats.  
3. Ensure that the interconnect cable will reach from the monitor  
location to the power supply module location.  
Front panel and remote controls. These controls allow  
adjustment of the video settings, control of the backlighting,  
format, and video source. (For more information, see “  
Remote Control” on page 4).  
4. If the mounting surface is not perfectly flat, bend the flanges  
on the mounting foot for the best fit without yet removing the  
backing from the flange’s double-sided tape.  
RCA video inputs.  
5. Remove the tape backing and press the pedestal into place.  
RCA auxiliary video output.  
6. Screw the pedestal into place with the mounting screws  
provided.  
7. Slide the monitor onto the pedestal as shown, and tighten the  
adjustment knob. Adjust viewing angle as needed.  
Important Notices  
NEVER install this monitor where it can be viewed from the  
driving position; this is a violation of many state and local  
vehicle codes.  
Use this monitor only after proper installation by a qualified  
installer.  
Avoid mounting locations where there is a risk of impact  
with a passenger in the event of an accident.  
Always mount the monitor securely using the mounting  
hardware that is provided. Do not use the monitor unless it  
is properly secured to the vehicle.  
Avoid touching the LCD screen except when cleaning it with a  
soft dry cloth.  
UN7000 7” Widescreen Universal Monitor  
Page 4  
UN7000 7” Widescreen Universal Monitor  
Page 13  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Installation  
Operating Guide  
Electrical Installation  
Operating Guide  
Begin installation of the Widescreen Universal Monitor by installing  
the power supply module and routing cables, as shown.  
Remote Control  
The remote control includes the following buttons for use with this  
monitor: Monitor Menu, Mode, Up, Down, and Power. Other buttons  
on the remote do not control the monitor.  
RCA connections:  
Video source 2  
(Input)  
Video source 1  
(Input)  
Video Out  
Power Supply Module  
Down  
Up  
CH/DISC/SET  
POWER  
MODE  
MENU  
Power  
Mode  
Monitor Menu  
1
4
7
2
5
8
3
Monitor  
Interconnect Cable  
Four-wire power harness:  
Yellow:  
6
9
MEMORY  
12V(+) constant power (battery)  
Red:  
12V(+) switched (accessory)  
MUTE  
0
Black:  
negative chassis ground  
VOL  
BAND  
DISP  
SCAN  
REP  
SAVE  
Blue:  
12V(+) output, 1A capable  
RC-1029A  
MOBILE AV REMOTE CONTROL  
Note:  
Note:  
This system is intended for 12-volt negative-ground  
systems only.  
To avoid damage to the power supply module, never leave  
the blue wire bare when unused or when it is shorted to  
the chassis ground.  
UN7000 7” Widescreen Universal Monitor  
Page 12  
UN7000 7” Widescreen Universal Monitor  
Page 5  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Operating Guide  
Installation  
Front Panel Controls  
The front panel controls are located on the lower edge of the monitor.  
Installation  
The Widescreen Universal Monitor includes mounting options  
described in the following sections. Before you install the monitor,  
consider the following important notices:  
NEVER install this monitor where it can be viewed from the  
driving position; this is a violation of many state and local  
vehicle codes.  
Avoid mounting locations where there is a risk of impact with  
a passenger in the event of an accident.  
Always mount the monitor securely using the mounting  
hardware that is provided. Do not use the monitor unless it is  
properly secured to the vehicle.  
The Installer accepts all responsibility for the suitability of  
this product installation. Rosen Entertainment Systems is not  
liable for any damages, incidental or otherwise, which may  
occur from the installation of this product.  
Box Contents  
IR Remote  
Receiver  
Down  
Menu  
Up  
Power/  
Mode  
The Rosen Widescreen Universal Monitor includes the following  
parts and equipment:  
UN7000 7" Monitor  
monitor  
remote control  
power supply module  
mounting pedestal  
flush mounting trim ring  
spacer ring for the flush mount trim ring  
monitor interconnect cable  
four-wire power supply harness  
mounting screws  
removal key to release the monitor from flush mount trim ring  
UN7000 7” Widescreen Universal Monitor  
Page 6  
UN7000 7” Widescreen Universal Monitor  
Page 11  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Operating Guide  
Operating Guide  
Turning On and Off the Monitor  
ResetAll Settings  
To turn on the monitor:  
The Reset menu option enables you to restore all settings to their  
original factory values.  
Press and release the POWER button on the monitor or the  
remote control.  
To reset all settings:  
To turn off the monitor:  
Press and hold the POWER button on the monitor or the  
remote control.  
1. Press Menu on the monitor or Monitor Menu on the remote  
control. The OSD menu appears.  
2. Press Menu on the monitor or Monitor Menu on the remote  
control until the arrow points to “Reset.”  
Changing Video Inputs  
3. Press or to return all settings to factory defaults.  
The monitor can be used with either NTSC or PAL video signals.  
NTSC is the North American video standard and is compatible with  
all Rosen video sources.  
4. Press Menu on the monitor or Monitor Menu on the remote  
control again to exit the menu. The menu disappears after 5  
seconds if no buttons are pressed.  
To change the active video input:  
1. Press the POWER button to turn on the monitor.  
2. Press MENU on the monitor or MENU on the remote control.  
The following screen appears in the monitor.  
AV1 : NTSC  
MODE  
MENU  
“AV1” appears briefly when AV1 is the active input.  
“AV2” appears briefly when AV2 is the active input.  
3. Press or to toggle between NTSC or PAL.  
4. Press POWER on the monitor, or MODE on the remote  
control to toggle between “AV1” and “AV2.”  
5. Press MENU on the monitor, or MENU on the remote control  
again, to exit the menu.  
UN7000 7” Widescreen Universal Monitor  
Page 10  
UN7000 7” Widescreen Universal Monitor  
Page 7  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Operating Guide  
Operating Guide  
Dimming the Backlight  
The Widescreen Universal Monitor features an adjustable backlight  
that dims or brightens the monitor to enhance viewing in varying  
lighting conditions.  
MODE  
MENU  
To adjust the backlight:  
COLOR  
32  
1. Press the Menu button on the monitor or Monitor Menu on  
the remote control. The OSD menu appears.  
4. Press Menu on the monitor or Monitor Menu on the remote  
control again to exit the menu. The menu disappears after  
5 seconds if no buttons are pressed.  
MODE  
MENU  
COLOR  
BRIGHT  
TINT  
DIMMER  
FORMAT  
RESET  
Image Formats  
The Widescreen Universal Monitor includes three image formats:  
“Normal,” “Full,” and “Zoom.” “Normal” is used in most VHS  
applications. “Full” can use the widescreen image produced by  
DVDs. In order to use the DVD’s “enhanced for 16:9 television,”  
(sometimes known as anamorphic video or widescreen) set the  
monitor’s image format to “Full.”  
2. Press Menu on the monitor or Monitor Menu on the remote  
control until the arrow points to “Dimmer.”  
3. Press or to turn the dimmer on or off.  
4. Press Menu on the monitor or Monitor Menu on the remote  
control three times to exit the menu. The menu disappears  
after 5 seconds if no buttons are pressed.  
Normal  
Full  
Zoom  
Adjusting the Color, Brightness, and Tint  
If necessary, you can adjust the color, brightness, and tint of the  
monitor.  
To change the image format:  
To adjust color, brightness, or tint settings:  
1. Press Menu on the monitor or Monitor Menu on the remote  
control. The OSD menu appears.  
1. Press the MENU button on the monitor or Monitor Menu on  
the remote control. The OSD menu appears.  
2. Press Menu on the monitor or Monitor Menu on the remote  
control until the arrow points to “Format.”  
2. Press MENU on the monitor or on the remote control until the  
arrow points to “Color,” “Brightness,” or “Tint.”  
3. Press or to select a format.  
3. Press the and buttons to adjust the setting. The setting  
will be displayed on the screen, as shown. There are 64 steps  
of adjustment. The default setting is 32 on a 64-step scale.  
4. Press Menu on the monitor or Monitor Menu on the remote  
control again to exit the menu. The menu disappears after 5  
seconds if no buttons are pressed.  
UN7000 7” Widescreen Universal Monitor  
Page 8  
UN7000 7” Widescreen Universal Monitor  
Page 9  
Download from Www.Somanuals.com. All Manuals Search And Download.  

Radio Shack Cordless Telephone ET 905 User Guide
Radio Shack Radar Detector 22 1670 User Guide
Raymarine TV Mount E46034 User Guide
RCA VCR VPT 385 User Guide
Remington Electric Shaver 400 User Guide
Ricoh Printer M035 User Guide
Roberts Radio Clock Radio DreamTime2 User Guide
Rosewill Computer Hardware RC501 User Guide
Rotel Stereo Receiver RX404 User Guide
Rover Lawn Mower 75M93 User Guide