®
I
SS
HIGH DEFINITION
COMPONENT SYSTEMS
PCH-14X
PCH-314 / PCH-414
PCH-514 / PCH-614
INSTALLATION & OPERATION
®
®
Download from Www.Somanuals.com. All Manuals Search And Download.
TABL E O F C O N T E N T S
Package Contents .................................................................................... 1
Introduction ............................................................................................ 1
Technical Design Features ...................................................................... 2
Installation Considerations ...................................................................... 4
Tools Needed .................................................................................... 4
Placing the Punch Splits Speakers ...................................................... 4
Installation .............................................................................................. 6
Mounting the Midrange ..................................................................... 6
Flush Mounting the Tweeter .............................................................. 7
Surface Mounting the Tweeter ........................................................... 7
Mounting the Punch Splits Plates....................................................... 8
Crossover Installation .............................................................................. 8
Troubleshooting .................................................................................... 12
Specifications ........................................................................................ 13
Warranty Information ............................................................................ 14
International Information ....................................................................... 15
G E T T I N G ST A R T E D
Welcome to Rockford Fosgate! This manual is designed to provide
information for owner, salesperson and installer. For those of you who
want quick information on how to install this product, please turn to the
Installation Section ofthismanualorreferto the iconslisted below. Other
information can be located by using the Table of Contents. We, at
Rockford Fosgate, have worked very hard to make sure all the information
in this manual is current. But, as we are constantly finding new ways to
improve our product, this information is subject to change without notice.
I
N
S
T
A
L
L
A
T
I
®
®
TROUBLE-
S
H
O
O
T
I
N
G
O
N
Sections marked
INSTALLATION
Sections marked
TROUBLESHOOTING
include “slam dunk”
assembly and wiring connections
include recommendations for
curing installation problems
Download from Www.Somanuals.com. All Manuals Search And Download.
PACKAGE CO NTENTS
PCH-14x
PCH-314
(1) Installation & Operation Manual
(2) 3/4" Tweeter
(1) Installation & Operation Manual
(2) 3/4" Tweeter
(2) TX-4186 Crossover
(2) Surface Mount Base
(2) Surface Mount Cup
(2) Flush Mount Base
(2) Flush Mount Cup
(2) 3" Midrange Speaker
(2) 4x6 Mounting Plate
(2) TX-4186 Crossover
(2) 100µf Capacitor
(2) Surface Mount Base
(2) Surface Mount Cup
(2) Flush Mount Base
(2) Flush Mount Cup
(8) #8 x 1.24 Screw
PCH-414/PCH-514 or PCH-614
(1) Installation & Operation Manual
(2) 3/4" Tweeter
(2) 4", 5" or 6" Midrange Speaker
(2) PCH-142x Crossover
(2) Speaker Grille Ring
(2) Speaker Grille Gasket
(2) Surface Mount Base
(2) Surface Mount Cup
(2) Flush Mount Base
(2) Flush Mount Cup
(8) #8 x 1.24 Screw
(2) 15' 22 gauge Speaker Wire
IN TRO D U C TIO N
In today’s vehicles, space for everything is at a premium. Many times, the
space that car designers dedicate for the stereo system is an afterthought.
Rockford Fosgate realizes that people who want stereo systems in their
vehicles have to contend with these real world problems. Our solution is
the Punch Splits High Definition Component Systems. Punch Splits
speakers are designed to fit in factory locations of vehicles with little
modification while providing the awesome sound quality people have
come to expect from Rockford Fosgate.
– 1 –
Download from Www.Somanuals.com. All Manuals Search And Download.
TECHNICAL DESIGN FEATURES
Midrange Features
◆ PVA Treated Cone
The lightweight paper cones are treated with PVA (PolyVinyl Acetate) for
environmental stability and increased rigidity. This treatment promotes
smooth midrange performance and low frequency extension free of
distortion.
THE RESULT: Strong and lightweight high performance cones.
◆ Vented Pole Piece
The vented pole piece by design, ensures proper ventilation to cool the
voice coil and maintains lower operating temperatures. This increases the
thermal power handling of the speaker.
THE RESULT: Improves power handling by cooling the voice coil.
◆ High Temperature Voice Coil
The voice coil used in the Punch Series is of a high temperature copper
wire construction. The wire is wound in two layers on a black anodized
aluminum voice coil former. The voice coil former dissipates heat away
from the voice coil improving the speaker’s thermal stability and improv-
ing the reliability of the speaker.
THE RESULT: Improves reliability by dissipating generated heat.
◆ Nitrile Rubber Surround
The nitrile material is resilient to temperature variations and provides a
consistent support necessary for the linear motion of the speaker cone. In
addition, the inherent damping capabilities eliminates the transmission of
degrading sonic disturbances between the cone and the frame of the
speaker greatly improving the clarity of the speaker’s midrange frequency
response.
THE RESULT: Improves speaker's frequency response.
– 2 –
Download from Www.Somanuals.com. All Manuals Search And Download.
Tweeter Features
◆ Neodymium Magnets
The high ionic compound of neodymium enables a smaller tweeter
magnet assembly to be used as opposed to the much larger ferrite magnets
that are commonly used in speaker manufacturing.
THE RESULT: An efficient magnet which allows smaller tweeter
construction.
◆ Magnetic Fluid Cooling
Magnetic fluid is a synthetic liquid consisting of microscopic magnetic
particles. The fluid has four times the thermal conductivity as air which
makes it an ideal cooling agent. Magnetic fluid is injected into the voice
coil gap which helps dissipate heat generated by the voice coil.
THE RESULT: A thermal conductor which allows increased power
handling.
◆ Swivel Mount Design
The tweeter is encapsulated in a variable swivel housing. This design
allows direct dispersion of the tweeter in order to accommodate various
mounting positions. The swivel mount design allows the tweeter to
maximize its sonic potential.
THE RESULT: Precise tweeter imaging regardless of mounting position.
Crossover Features
◆ Adjustable Tweeter Level Matching
The passive crossovers utilize a series power resistor for tweeter level
matching. The factory set tweeter output level is 0dB, however can be
reduced –3dB to create a smoother transition between the midrange and
tweeter. The ability to level match allows the system to be custom “tuned”
for a particular listener or setup.
THE RESULT: Allows custom setup of tweeter output level.
– 3 –
Download from Www.Somanuals.com. All Manuals Search And Download.
◆ Optical Compression Circuit
The supplied passive crossovers utilize an optical compression circuit for
tweeter protection. This protection circuit absorbs the destructive signal
caused when the amplifier's output is clipped. This greatly increases the
power handling capability and the reliability of the tweeter.
THE RESULT: Increased tweeter reliability under harsh conditions.
◆ Passive Filter Bypass
The TX-4186 utilizes an extra screw terminal on the crossover housing
which allows the tweeters audio signal to “bypass” the internal passive
filter. This feature allows an external active filter to be used while
maintaining optical compression for tweeter reliability.
THE RESULT: System flexibility with constant tweeter protection.
INSTALLATION CONSIDERATIONS
Since many of the Punch Splits speakers are designed for direct replace-
ment in factory speaker locations, some of the following instructions will
not apply. To maximize the performance in difficult or custom installa-
tions, please see your Authorized Rockford Fosgate Dealer.
Warning! Please read the entire Installation section before attempting the
installation of your Punch Splits Speakers.
Tools Needed
The following is a list of some of the tools necessary for the installation of
the Punch Splits speakers.
Power Drill with assorted bits
Volt Meter
Wire Strippers
Wire Crimpers
Marking Pen
Hole Saw Arbor
Assorted Hole Saws
(Midrange)
Assorted Screwdrivers
Tape Measure
Hole Saw (11⁄4")
(Tweeter)
Placing the Punch Splits Speakers
A solid front stage with a good image is one of the most difficult tasks to
achieve in a vehicle. No car has the optimum listening environment. This
makes proper sound staging very difficult to accomplish. Most speakers
tend to be placed where they will fit easily, as opposed to where they can
perform the best The mounting location of your Punch Splits speakers will
have a great effect on the sound quality of your stereo system. The special
care taken to place the Punch Splits speakers, will yield many hours of
listeningenjoymentin return. Severalimportantrecommendationsshould
be followed.
– 4 –
Download from Www.Somanuals.com. All Manuals Search And Download.
I
®
®
N
S
T
A
L
L
A
T
I
• Place the speakers where they have
a direct path to the listening area.
• When using the Punch Splits, there
are two options for speaker place-
ment between the midrange and
tweeter. For the best integration be-
tween the midrange and tweeter,
the tweeter should be placed less
than 2"from the midrange. (Figure 1)
• If you cannot place the tweeter less
O
N
2" or less
Figure 1
than 2" from the midrange, then place the tweeter more than 7"
from the midrange. Placing the tweeter 2"-7" from the midrange
can cause destructive interference (frequency response prob-
lems) which will affect the speaker’s ability to reproduce the
frequency range around the crossover frequency of the Punch
Splits system.
• Whenever possible, place the tweeter directly above or below
the midrange as this maximizes the imaging (point source)
capability of the Punch Splits speakers. (Figure 2)
Figure 2-A
Figure 2-B
Soundradiatedfroma“pointsource”hasthemostoptimumstereo imaging
because the separation ofthe acousticalcentersbetween the midrange
and tweeter for each channel is at the optimum. Figure 2-Adescribes
a horizontal speaker alignment. In a closed environment such as an
automobile, horizontal speaker alignment can cause severe ampli-
tude and phase differences which will degrade not only the imaging,
but also the frequency response. This is due to the path length
differences between the midrange and tweeter. Figure 2-B displays
a vertical alignment between the midrange and tweeter. With a
vertical alignment, the path length differences between the midrange
and tweeter are reduced to a minimum. The result is a negligible
difference in path lengths between the midrange and tweeter regard-
less of the proximity of the listener to the speakers. Mounting the
– 5 –
Download from Www.Somanuals.com. All Manuals Search And Download.
I
®
®
N
S
T
A
L
L
A
T
I
Punch Splits speakers with minimum path length differences will
ensure the best staging and imaging possible from your audio
system.
O
N
IN STALLAT I O N
The mounting of the Punch Splits speakers and crossovers is just as
important as choosing the location for the speakers. Improper installation
will degrade the sound quality and reduce the reliability of the Punch
Splits speakers. To maximize the performance of your speakers, the
following criteria should be considered.
• After choosing possible locations for the speakers, it is important to
make sure there is a flat area large enough for the speaker to mount.
Warning !Failure to do this can cause damage to the speaker if the
frame of the speaker is bent during the installation.
• Check to see that the location is deep enough for the speaker and
the location does not interfere with the normal operation of the
vehicle.
• When mounting the speakers in the door of a vehicle, special care
should be taken to make sure the speaker/s do not interfere with
either the window operation or the door opening and closing. (Be
careful of the tension bar in the door.)
• When mounting the speakers on the rear deck of the vehicle,
double checkthe operation ofthe rearhatch ortrunklid. Make sure
the tension bars and other moving parts are not obstructed by the
speakers’ installation.
Refer to the Specifications section of the manual for the mounting depth
and proper diameter hole to cut for the Punch Splits speakers.
Mounting the Midrange
1. Cut the proper size hole for the midrange/woofer.
2. Place the mounting ring over the mounting hole and mark the location
of the screw mounting holes.
3. Remove the ring. Drill the holes for the screws using a 1/8" drill bit.
4. Route the wire through the hole.
– 6 –
Download from Www.Somanuals.com. All Manuals Search And Download.
I
®
®
N
S
T
A
L
L
A
T
I
5. Place the mounting ring over the hole.
6. Attach the wires and be sure to observe the proper speaker
polarity. Keep the speaker wires away from sharp and
moving objects.
O
N
7. Place the speaker into the hole and screw the speaker into place.
Be careful not to bend the speaker frame during this step.
8. Press the speaker grille into the mounting ring.
Flush Mounting the Tweeter
1. Cut a 1-1/4" mounting hole.
2. Route the wires through the mounting hole.
3. Attach the wires and be sure to observe the proper speaker polarity.
Keep the speaker wires away from sharp and moving objects.
4. Snap the tweeter with the flush mount capsule into the hole.
5. Angle the tweeter for best sonic performance.
Surface Mounting the Tweeter
Mounting
Plate
1. Place the mounting plate on the surface where the tweeter will be
located. Marktwo (2)opposingmountingholesand the centerwire
access hole.
2. Remove the mounting plate and drill a 1/4" (6.4mm) hole for the
speaker wire access. Drill two (2) 1/8" (3mm) holes for the
mounting screws.,
3. Route the wires through the mounting hole.
4. Place the mounting plate in position by threading the speaker wires
through the center hole. Mount the mounting plate with the
provided mounting hardware.
5. Attach the wires and be sure to observe the proper speaker polarity.
Keep the speaker wires away from sharp and moving objects.
6. Snap the tweeter onto the mounting plate.
– 7 –
Download from Www.Somanuals.com. All Manuals Search And Download.
I
®
®
N
S
T
A
L
L
A
T
I
Mounting the Punch Splits Plates
O
N
1. Cut the proper size hole for the midrange/woofer and
tweeter. The midrange/woofer hole should be slightly
larger than the mounting plate woofer hole.
2. Place the mounting plate over the mounting holes and mark the
location of the screw mounting holes.
3. Remove the ring. Drill the holes for the screws using a 1/8" drill bit.
4. Mount the speaker plate.
Be careful not to bend the mounting plate during this step.
5. Route the wires through the holes.
6 Attach the wires and be sure to observe the proper speaker polarity.
Keep the speaker wires away from sharp and moving objects.
7. Place the speaker into the hole and snap the speakers into place.
Note: Follow Steps 4 & 5 of Flush Mount Tweeter for tweeter.
CRO SSO VER INSTALLATIO N
Wiring the PCH-142x
®
®
ACTIVE TWEETER PROTECTION
PCH-142x
®
Striped
Wire
+
–
–
+
+
–
Output from
Amplifier
• Striped Wire indicates “+” terminal of tweeter
– 8 –
Download from Www.Somanuals.com. All Manuals Search And Download.
I
®
®
N
S
T
A
L
L
A
T
I
Wiring the PCH-314
O
N
®
®
®
ACTIVE TWEETER PROTECTION
TX-4186
(Rear View)
PCH-14
–
+
–
+
+
Dot indicates
“+” Terminal
Input
Protection
Striped Wire
(Rear View)
PCH-34
Dot indicates
“+” Terminal
–
+
Output from
Amplifier
100µf
capacitor
– 9 –
Download from Www.Somanuals.com. All Manuals Search And Download.
I
®
®
N
S
T
A
L
L
A
T
I
Wiring the TX-4186
(Crossover/Tweeter Protection)
O
N
TWEETER
PROTECTION
CROSSOVER
®
+
–
+
–
Tweeter
Output
Input
Protection
Input
+
–
OUTPUT
FROM
AMPLIFIER
+
–
• Striped Wire indicates “+” terminal of tweeter
Wiring the TX-4186
(Tweeter Protection Only)
TWEETER
PROTECTION
®
+
–
+
–
Input
Protection
Tweeter
Output
Input
+
–
OUTPUT
FROM
AMPLIFIER
–
+
• Striped Wire indicates “+” terminal of tweeter
• WARNING: Use an external high-pass filter of at least 6kHz
@ 18dB when configuring crossover for Tweeter Protection
Only Mode
– 10 –
Download from Www.Somanuals.com. All Manuals Search And Download.
I
®
N
S
T
A
L
L
A
T
I
Tweeter Level Matching
O
N
(Bottom view of PCH-142x/TX-4186
Cut jumper
wire for –3dB
• Factory set tweeter level is 0dB
• Cut jumper wire on bottom of crossover to reduce
tweeter level by –3dB
Horizontal Logo Mounting
®
®
T X - 4 1 8 6
A C T I V E T W E E T E R P R O T E C T I O N
®
ACTIVE TWEETER PROTECTION
TX-4186
®
®
®
• Configure logo into desired position and snap into place
Vertical Logo Mounting
®
®
• Configure logo into desired position and snap into place
– 11 –
Download from Www.Somanuals.com. All Manuals Search And Download.
TROUBLE-S
H
O
O
T
I
N
G
TR O U BL E SH O O T I N G
Symptom
Diagnosis
Remedy
No sound from
speakers
Check and repair or
replace wiring as needed.
Wires between amplifier,
crossover and speakers
not connected properly.
Check system with known
working amplifier and re-
pair or replace as needed.
Amplifier has no output.
Check for shorts in the
wiring with a volt/ohm
meter and repair or
Speaker wires are
shorted to each other or
to the chassis of the
vehicle.
replaced wires as needed.
Check system with known
working speaker and repair
or replace as needed.
Speakers are blown.
Tweeters “burn
up” easily
Crossover is in “passive fil-
ter bypass” configuration.
Check wiring and re-config-
ure as needed.
External crossover is not fil-
tering the tweeter properly.
Check configuration of ex-
ternal crossover and re-con-
figure for at least 6kHz @
18dB/octave
Excessive clipping from
amplifier.
Check gain settings on am-
plifier and readjust as
needed.
Equalizerin system (ifavail-
able) has excessive boost in
the high frequency range.
Check settings on equalizer
and readjust as needed.
Distorted sound
from speakers
Incorrect wiring between
crossover and speakers
Check wiring and repair
or replace as needed.
Speaker wires shorted
to chassis of vehicle.
Check for shorts in the wir-
ing with a volt/ohm meter
and repair or replace wires
as needed.
Engine Noise
from One
or More
Speakers
Crossover ismounted near
radiated noise source.
(Powercables, computers,
etc.)
Move crossovers away from
noise sources. (Refer to In-
stallation section of manual
on crossovers.)
– 12 –
Download from Www.Somanuals.com. All Manuals Search And Download.
– 13 –
Download from Www.Somanuals.com. All Manuals Search And Download.
LIMITED W AR R AN T Y I N FO R M AT I O N
Rockford Corporation offers a limited warranty on Rockford Fosgate products on the
following terms:
•
Length of Warranty
1 year on speakers
30 days on speaker B-stock (receipt required)
90 days on electronic B-stock (receipt required)
3 years on electronics
2 years on source units
•
What is Covered
This warranty applies only to Rockford Fosgate products sold to consumers by
Authorized Rockford Fosgate Dealers in the United States of America or its
possessions. Product purchased by consumers from an Authorized Rockford
Fosgate Dealer in another country are covered only by that country’s Distributor
and not by Rockford Corporation.
•
Who is Covered
This warranty covers only the original purchaser of Rockford product purchased
from an Authorized Rockford Fosgate Dealer in the United States. In order to
receive service, the purchaser must provide Rockford with a copy of the receipt
stating the customer name, dealer name, product purchased and date of purchase.
•
•
Products found to be defective during the warranty period will be repaired or
replaced (with a product deemed to be equivalent) at Rockford's discretion.
What is Not Covered
1. Damage caused by accident, abuse, improper operations, water, theft
2. Any cost or expense related to the removal or reinstallation of product
3. Service performed by anyone other than Rockford or an Authorized Rockford
Fosgate Service Center
4. Any product which has had the serial number defaced, altered, or removed
5. Subsequent damage to other components
6. Any product purchased outside the U.S.
7. Any product not purchased from an Authorized Rockford Fosgate Dealer
•
•
Limit on Implied Warranties
Any implied warranties including warranties of fitness for use and merchantability
are limited in duration to the period of the express warranty set forth above. Some
states do not allow limitations on the length of an implied warranty, so this
limitation may not apply. No person is authorized to assume for Rockford Fosgate
any other liability in connection with the sale of the product.
How to Obtain Service
Please call 1-800-669-9899 for Rockford Customer Service. You must obtain an
RA# (Return Authorization number)to return anyproductto Rockford Fosgate. You
are responsible for shipment of product to Rockford.
Ship to: Speakers
Ship to: Electronics
Rockford Corporation
Warranty Repair Department
2055 E. 5th Street
Rockford Acoustic Design
(Receiving-speakers)
609 Myrtle N.W.
Grand Rapids, MI 49504
RA#:_________________
Tempe, AZ 85281
RA#:_________________
– 14 –
Download from Www.Somanuals.com. All Manuals Search And Download.
– 15 –
Download from Www.Somanuals.com. All Manuals Search And Download.
Asegurese de leer las instrucciones antes de instalar estos productos.
INTRODUCCIÓN
En los vehiculos de hoy en dia, premia el espacio para todo. Muchas
veces, el espacio que los diseñadores de coches dedican al equipo de
música es un requerimiento posterior al diseño. Rockford Fosgate sabe
que la gente que quiere equipos de música en sus vehiculos, debe pelear
con este problema cotidiano. Nuestra solución es los sistema de
componentes de Alta definicíon Punch Split. Los altavoces Punch Split
están diseñados para ser situados en los lugares dispuestos por la fábrica
de los vehiculos con sólo una ligera modificación, ofreciendo la calidad
de sonido que la gente espera de Rockford Fosgate.
LUGAR DE MONTAJE
•
Para obtener una buena integración
entre el altavoz de medios y el tweeter,
el tweeter debe estar situado a menos
de dos pulgadas del altavoz. (Figura 1)
no superior a 5cm
Figura 1
I
®
®
N
S
INSTALACIÓN
T
A
L
L
A
T
I
O
N
Montaje del altavoz de medios
1. Corte el agujero de tamaño exacto para el altavoz de medios o
woofer.
• Para el PCH-44, corte un agujero de 96,8mm de diámetro
• Para el PCH-54, cortelo de 123,8mm
• Para el PCH-64, cortelo de 144,5mm
2. Coloque el aro de montaje sobre el agujero y marque la posición de
los agujeros para los tornillos.
3. Saque el aro de montaje, Perfore los agujeros para los tornillos de
sujeción usando una broca de 1/8" (3mm).
– 16 –
Download from Www.Somanuals.com. All Manuals Search And Download.
4. Coloque el cable a través del agujero.
5. Coloque el aro de montaje sobre el agujero.
6. Conecte los cables al altavoz observando la polaridad del mismo.
7. Coloque el altavoz en el agujero y atornillelo. Tenga cuidado en
no doblar el soporte del altavoz durante este paso.
8. Presione la reja del altavoz sobre el aro de montaje.
Montaje empotrado del Tweeter
1
1. Corte un agujero de 1 ⁄4" (32mm).
2. Coloque los cables a través del agujero de montaje.
3. Conecte los cables observando la polaridad del altavoz. Aleje los
cables de objetos móbiles o punzantes.
4. Encaje el tweeter con la capsula de montaje en el agujero.
5. Oriente el tweeter hacia donde obtenga una mejor caracteristica
del sonido.
Montaje superficial del Tweeter
Superficie
de montaje
1. Coloque la superficie de montaje donde se situará el tweeter.
Marque dos agujeros opuestos y haga el agujero contral para el
acceso del cable.
2. Saque la superficie de montaje y perfore con una broca de 6.4mm
para el acceso del cable. Perfore los agujeros para los tornillos con
una broca de 3mm.
3. Pase los cables a través de los agujeros.
4. Coloque la superficie de montaje en la posición, pasando los
cables por el agujero central.
5. Conecte los cables y asegurese de observar la polaridad del
altavoz. Aleje los cables de objetos móbiles o punzantes.
6. Encaje el tweeter en la superficie de montaje.
– 17 –
Download from Www.Somanuals.com. All Manuals Search And Download.
Conectando el PCH-142x
®
®
ACTIVE TWEETER PROTECTION
PCH-142x
®
El hilo
marcado
+
–
–
+
+
–
Salida del
Amplificador
• El hilo marcado indica el “+” del tweeter
Ajuste de Nivel del Tweeter
(Vista inferior del PCH-142x/TX-4186)
Corte el cable para
obtener –3dB
• El ajuste de origen es –0dB
• Corte el hilo en la parte inferior del tweeter para una
reduccion del nivel del tweeter de –3dB
Conectando el TX-4186
(Crossover/Proteccion de Tweeter)
Protección del Tweeter
Crossover
®
El hilo
marcado
+
–
+
–
Tweeter
Input Output
Input
+
–
Salida del
Amplificador
Protection
+
–
• El hilo marcado indica el “+” del tweeter
– 18 –
Download from Www.Somanuals.com. All Manuals Search And Download.
ATTENTION: Veuillez lire les instructions suivantes pour l'installation de ces
produits.
INTRODUCTION
Dans les véhicules actuels, l'espace est primor dial. Dans beaucoup de
cas, l'espace dédié au système audio par les fabricants d'automobiles se
retrouve au second plan. Rockford Fosgate réalise que les gens qui
veulentun système audio dansleurvoiture sontconfrontésà ce problème.
Notre solution est le système voies séparées Punch Splits. Les haut-
parleurs Splits sont conçus pour être installés dans les emplacements
d'origine après une légère modification tout en reproduisant la qualité
sonore que les gens attendent de Rockford Fosgate.
EMPLACEMENT DE MONTAGE
•
Pour bénéficier d'une harmonie maxi-
mum entre le médium et l'aigu
l'éloignement entre ces deux haut-
parleurs devrait être de moins de 5cm
entre les 2 châssis. (Figure 1)
moins de 5cm
Figure 1
I
N
S
T
A
L
L
A
T
I
®
®
INSTALLATION
O
N
Montage du haut-parleur médium
1. Découper un trou adapté au haut-parleur médium/woofer.
• Pour le PCH-44, le diamètre du trou est de 96,8mm
• Pour le PCH-54, le diamètre du trou est de 123,8mm
• Pour le PCH-64, le diamètre du trou est de 144,5mm
2. Placer l'anneau de montage sur le trou et repérer l'emplacement des
des vis.
3. Retirer l'anneau. Percer les trous des vis en utilisant une mèche de
3mm.
– 19 –
Download from Www.Somanuals.com. All Manuals Search And Download.
4. Faire passer les fils dans le trou central.
5. Placer l'anneau de montage au-dessus du trou central.
6. Connecter les fils au haut-parleur en respectant les polarités.
Eloigner les fils de toute partie tranchante ou mobile du véhicule.
7. Placer le haut-plarleur au-dessus du trou central. Visser le haut-
parleur dans son emplacement. Faire attention a ne pas tordre le
chassis du haut-parleur durant cette etape de montage.
8. Mettre la grille dans l'anneau de montage.
Montage encastré du tweeter
1. Découper un trou de montage de 32mm.
2. Faire passer le fil dans le trou de montage.
3. Connecter les fils au haut-parleur en respectant les polarités.
Eloigner les fils de toute partie tranchante ou mobile du véhicule.
4. Clipser le tweeter avec la capsule d'encastrement dans le trou.
5. Diriger le tweeter pour atteindre la meilleure qualité de sonore.
Montage en surface du tweeter
Plaque de
Montage
1. Placer la plaque de montage en surface la où le tweeter doit être
installé. Marquer deux (2) trous de montage opposés et le trou
central pour le fil.
2. Enlever la plaque de montage et percer un trou de 6,4 mm pour le
trou central du fil. Percer deux (2) trous de 3mm pour les visses de
montage.
3. Diriger les visses dans les trous de montage.
4. Placer la plaque de montage en position en faisant passer les fils à
travers du trou central.
5. Connecter les fils au haut-parleur en respectant les polarités.
Eloigner les fils de toute partie tranchante ou mobile du véhicule.
6. Clipser le tweeter sur la plaque de montage.
– 20 –
Download from Www.Somanuals.com. All Manuals Search And Download.
Branchement du PCH-142x
®
®
ACTIVE TWEETER PROTECTION
PCH-142x
Fil
®
marqué
+
–
–
+
+
–
Sortie de
l'empli
• Le fil marqué indique la connexion “+” du tweeter
Compensation du Niveau Aigu
Vue d'en bas du PCH-142x/TX-4186
Coupez le pontage au
verso du filtre pour –3dB
• Le niveau de défaut est de –0dB
• Coupez le pontage au verso du filtre our atténuer
l'aigu de 3dB.
Branchement du TX-4186
Filtre passe-haut / Protection du tweeter
Filtre
Protection du Tweeter
®
+
–
+
–
Sortie du
Tweeter
Entrée
Entrée
+
–
Sortie de
l'empli
+
–
Protection
• Le fil marqué indique la connexion “+” du tweeter
– 21 –
Download from Www.Somanuals.com. All Manuals Search And Download.
Bitte lesen Sie diese Gebrauchsanleitung zuerst sorgfältig durch. Das kann
Sie vor dem falschen Einsatz, Ausfallen oder sogar BeschädigungdesProduktes
oder Ihres Fahrzeuges schützen.
EINLEITUNG
In Fahrzeugen unserer heutigen Zeit ist Platz oft sehr begrenzt. Oftmals
sind die vom Werk vorgesehenen Plätze für Lautsprecher sehr
unzureichend. Rockford Fosgate hat verstanden, daβ es für Viele, die eine
Stereoanlage im Auto wollen ein groβes Problem ist. Die Lösung dafür ist
dasPunch SplitsKomponenten-System. Punch SplitsLautsprecherwurden
designed um in Originaleinbauplätzen Raum zu finden und dabei die
gute Klangqualität zu liefern, die Sie von Rockford Fosgate gewöhnt sind.
EINBAUORT
•
Für die beste Integration zwischen
Mittel- und Hochtöner sollte der
Hochtöner niemals weiter wie 5 cm
vom Mitteltöner entfernt sein.
5 cm oder weniger
Figure 1
I
N
S
T
A
L
L
A
T
I
®
®
MONTAGE
O
N
Montage des Mitteltöners
1. Schneiden Sie die richtige Lochgröβe für den Mitteltöner/Woofer aus.
• Für den PCH-44, ein 96,8mm Durchmesserloch
• Für den PCH-54, ein 123,8mm Durchmesserloch
• Für den PCH-64, ein 144,5mm Durchmesserloch
2. Plazieren Sie den Montagering über dem vorgesehenen Ausschnitt
und markieren Sie die Schraubenlöcher.
3. EntfernenSiedenRingundbohrenSie dieLöcherfürdenMontageringvor.
4. Führen Sie das Kabel durch das Loch.
– 22 –
Download from Www.Somanuals.com. All Manuals Search And Download.
5. Montieren Sie den Lautsprecherring.
6. Schlieβen Sie den Lautsprecher an und achten Sie darauf, daβ die
Polung stimmt.
7. Plazieren Sie den Lautsprecher und schrauben Sie ihn fest. Bitte
achten Sie darauf, daβ der Lautsprecherkorb sich beim
Festschrauben nicht verzieht.
8. Pressen Sie das Lautsprechergitter vorsichtig in den Montagering.
Hochtöner-Einbaumontage
1. Schneiden Sie ein 1-1/4" (32mm) Montageloch.
2. Führen Sie die Lautsprecherkabel durch dieses Loch.
3. Klemmen Sie die Lautsprecherkabel am Lautsprecher an. Achten Sie
auf die Polung und das die Kabel an keiner scharfen Kante anliegen.
4. Pressen Sie den Hochtönermitseinem Gehäuse in dasvorgesehene
Loch.
5. Drehen Sie den Hochtöner in die klangbeste Stellung.
Hochtöner-Aufbaumontage
Montageplatte
1. Plazieren Sie die Montageplatte des Hochtöners auf die
vorgesehene Stelle. Markieren Sie 2 Befestigungslöcher und 1
Mittelloch für das Kabel.
2. Entfernen Sie die Montageplatte und bohren Sie ein Mittelloch
von 6,4 mm fürdasLautsprecherkabelsowie 2 Befestigungslöcher
von 3 mm für die Schrauben.
3. Führen Sie die Kabel durch das vorgesehene Loch.
4. Plazieren Sie die Montageplatte, führen Sie die Lautsprecherkabel
durch das Mittelloch und montieren Sie die Montageplatte.
5. Klemmen Sie die Lautsprecherkabel am Lautsprecher an. Achten
Sie auf die Polung und das die Kabel an keiner scharfen Kante
anliegen.
6. Pressen Sie den Hochtöner auf die Montageplatte.
– 23 –
Download from Www.Somanuals.com. All Manuals Search And Download.
Verkabelung des PCH-142x
®
®
ACTIVE TWEETER PROTECTION
PCH-142x
das
®
abisolierte
Kabel
+
–
–
+
+
–
Ausgang vom
Verstärker
• das abisolierte Kabel zum “+” Terminal des Hochtöners
Tweeter Level Matching
(Vorderansicht)
Trennen Sie die
Kabelbrücke um
–3dB zu erreichen
• Werkseinstellung Hochtonpegel –0dB
• Durch Trennen der Kabelbrücke reduzieren Sie den Pegel
des Hochtöners um –3dB
Verkabelung des TX-4186
(Frequenzweiche/Hochton Sicherung)
Crossover
Tweeter Protection
®
Eingang
Hochtonschutz
+
–
+
–
Hochton
Ausgang
Input
+
–
Ausgang vom
Verstärker
+
–
• das abisolierte Kabel zum “+” Terminal des Hochtöners
– 24 –
Download from Www.Somanuals.com. All Manuals Search And Download.
Si prega di leggere le istruzioni prima di procedere all'installazione.
INTRODUZIONE
Negli autoveicoli di oggi non c'é molto spazio. Molte volte i progettisti di
automobili si accorgono solo a vettura ultimata che mancano gli spazi per
gli impianti stereo. Rockford Fosgate é conscia del fatto che la gente che
vuole realizzare degli impianti stereo sulle properie autovetture deve
affrontare questo problema. La soluzione che proponiamo consiste nel
Punch Splits High Definition Component Systems. Gli altoparlanti Punch
Splits sono ideati per essere installati, con piccole modifiche, negli spazi
predisposti per gli impianti, riuscendo cosí a riprodurre la grandiosa
qualitá del suono che la gente si aspetta da Rockford Fosgate.
POSIZIONAMENTO
•
Per ottenere la migliore integrazione
tra tweeter e midrange vi suggeriamo
di posizionare i due componenti a
meno di 5 cm tra loro (fig. 1).
meno di 5cm
Figura 1
I
N
S
T
A
L
L
A
T
I
®
INSTALLAZIONE
O
N
Installazione del Midrange
1. Praticate un foro adatto per il midrange/woofer
• 96,8mm per PCH-44
• 123,8mm per PCH-54
• 144,5mm per PCH-64
2. Posizionate l'anello della griglia sul foro e segnate la posizione delle viti.
3. Togliete l'anello della griglia e forate il pannello con una punta da 3 mm.
4. Fate passare il cavo attraverso il foro praticato per l'altoparlante.
– 25 –
Download from Www.Somanuals.com. All Manuals Search And Download.
5. Posizionate la griglia spora il foro dell'altoparlante.
6. Collegate i cavi facendo attenzione alla corretta polaritá.
7. Posizionate l'altoparlante nel foro ed avvitatelo. Assicuratevi di
non piegare il cestello dell'altoparlante.
8. Incastrate la griglia sull'anello di fissaggio.
Installazione ad incasso del tweeter
1. Praticate un foro da 32mm.
2. Fate passare i cavi attraverso il buco.
3. Collegate i cavi facendo attenzione alla corretta polaritá.
4. Incastrate il tweeter con la flangia di montaggio nel foro.
5. Angolate il tweeter per ottenere la miglior qualitá timbrica.
Installazione a superficie del Tweeter
Flangia di
montaggio
1. Posizionate la flangia sulla superficie dove il tweeter sará
posizionato e segnate 2 fori diametralmente opposti ed uno al
centro per farvi passare il cavo.
2. Togliere la flangia e con una punta da 6,5 mm fare un foro per il
cavo dell'altoparlante. Pratciare 2 fori da 3 mm per le viti.
3. Far passare i cavi attraverso il foro praticato.
4. Posizionare la flangia in posizione infilando icavidell'altoparlante
attraverso ilforo centrale. Montare la flangia con le vitia dotazione.
5. Collegate i cavi prestando attenzione alla corretta polaritá.
Accertarsi che i cavi dell'altoparlante siano distanti da superfici
affilate e parti in movimento.
6. Incastrare il tweeter sulla flangia di montaggi.
– 26 –
Download from Www.Somanuals.com. All Manuals Search And Download.
Cablare il PCH-142x
®
®
ACTIVE TWEETER PROTECTION
PCH-142x
®
Cavi
spellati
+
–
Uscit–a
dell'amplificatore
+
+
–
• Il cavo spellato indica il positivo del tweeter
Regolazione del livello di emissione del tweeter
(Vista Posteriore del PCH-142x/TX-4186)
Tagliare il
ponticello per –3dB
• Il livello preimpostato é –0dB
• Tagliare il ponticello accessibile dal foro sul retro del
crossover per ottenere un'attenuazione del tweeter di –3dB
Cablare il TX-4186
(Crossover/Protezione del tweeter)
Crossover
Protezione del tweeter
®
ingresso
protezione
il cavo
spellato
+
–
+
–
Ingresso
uscita del tweeter
+
–
+
–
• Il cavo spellato indica il positivo del tweeter
– 27 –
Download from Www.Somanuals.com. All Manuals Search And Download.
NOTES
Download from Www.Somanuals.com. All Manuals Search And Download.
M ADE IN THE USA
This product is designed, developed and assembled in the USA by a dedicated
group of American workers. The majority of the components used in the
construction of this product are produced by American companies. However, due
to the global nature of their manufacturing facilities and the loudspeaker parts
industry in general, some parts may be manufactured in other countries.
Rockford Fosgate
Rockford Corporation
546 South Rockford Drive
Tempe, Arizona 85281 U.S.A.
In U.S.A., (602) 967-3565
In Europe, Fax (49) 4207-801250
In Japan, Fax (81) 559-79-1265
LIT9781
11/96
Download from Www.Somanuals.com. All Manuals Search And Download.
|