Roberts Radio Clock Radio CR9977 User Guide

CR9977  
2 Band Auto Set Dual Alarm  
Clock Radio  
Please read this manual before use  
Download from Www.Somanuals.com. All Manuals Search And Download.  
1
2
Controls  
(Top)  
3
4
5
11  
6
10  
9
8
7
1. Up/Hi button  
4. Snooze button  
5. Sleep button  
7. Alarm mode button  
8. Down/Low button  
9. On/Off button  
10. Alarm 2 button  
11. Alarm 1 button  
2. Time button  
3. Date button  
6. Alarm days button  
If you need any further advice, please call our Technical Helpline on :-  
Download from Www.Somanuals.com. All Manuals Search And Download.  
2
020 8758 0338 (Mon-Fri)  
Controls  
(Front)  
12  
12  
15  
14  
13  
12. PM indicator  
13. Low battery indicator  
14. Tuning dial  
15. Alarm 'On' indicator  
3
Download from Www.Somanuals.com. All Manuals Search And Download.  
Controls  
(Right side)  
16  
17  
18  
16. Tuning control  
17. Wave band selector switch  
18. Volume control  
If you need any further advice, please call our Technical Helpline on :-  
Download from Www.Somanuals.com. All Manuals Search And Download.  
4
020 8758 0338 (Mon-Fri)  
Controls  
(Base)  
20  
20. Battery compartment  
5
Download from Www.Somanuals.com. All Manuals Search And Download.  
Switching on  
1. Place your clock radio on a flat surface. Plug the power cord into the  
wall socket and switch on.  
2. After a few seconds the time, day and date will set automatically.  
Your clock radio is fitted with a long life back-up battery to maintain  
the factory set time, day and date. Your clock radio will automatically  
reset to the correct time should the power source be interrupted. It  
will also automatically adjust for summer/winter time.  
See section on Back-up battery on page 15 .  
Should the time, date or year require adjustment follow the procedure  
shown in the next sections.  
Setting the time manually  
1. Press and hold down the Time button.  
1
2
2. Whilst holding down the Time button press the Up or Down  
buttons to set the time. Release the buttons when the correct time  
is reached.  
The clock uses a 12 hour display with a PM indicator. Ensure that  
2
the correct 12 hour cycle is selected.  
If you need any further advice, please call our Technical Helpline on :-  
6
Download from Www.Somanuals.com. All Manuals Search And Download.  
020 8758 0338 (Mon-Fri)  
Setting the year manually  
1. To set the year hold down both theTime and Date buttons. The  
display will change to show the year.  
2
2. Whilst holding down the Time and Date buttons set the correct  
year by using the Up or Down buttons. When the Time and Date  
buttons are released the display will revert to showing the time.  
1
1
2
Setting the date manually  
1. To set the date hold down the Date button.  
2
2. Whilst holding down the Date button set the correct date using the  
Up or Down buttons.  
2
1
7
Download from Www.Somanuals.com. All Manuals Search And Download.  
Setting alarm times  
Your clock radio has two separate alarms which can be set to activate  
at different times.  
1
1. Press and hold down the Alarm 1 or Alarm 2 buttons.  
2. Whilst holding down the Alarm 1 or Alarm 2 buttons press the  
Up or Down buttons to set the alarm time. Release the buttons  
when the correct alarm time is reached. The clock uses a 12 hour  
display with a PM indicator. Ensure that the correct 12 hour cycle  
is selected.  
2
2
Setting alarm mode  
The alarms can be set to wake you by either the buzzer or the radio.  
2
1. Whilst holding down the Alarm 1 or Alarm 2 buttons repeatedly  
press and release the Alarm mode button until the display shows  
the required alarm mode e.g. Buzzer (  
),Radio (  
) or Off (  
).  
Release the buttons when the required alarm mode is reached. The  
display will return to showing normal time.  
It is possible to set Alarm 1 to wake to buzzer and Alarm 2 to wake  
to radio or vice versa.  
The Alarm indicator will illuminate when one or both of the alarms  
are set to either Buzz or Radio mode.  
The Alarm indicator will extinguish when both Alarms are set to  
Off.  
If you need any further advice, please call our Technical Helpline on :-  
8
Download from Www.Somanuals.com. All Manuals Search And Download.  
020 8758 0338 (Mon-Fri)  
Setting alarm day  
Your clock radio has five different day options for each of the alarms.  
The Alarm days are:  
Weekdays only display shows 1-5  
Weekends only display shows 6-7  
Everyday display shows 1-7  
Monday to Saturday display shows 1-6  
Sunday only display shows 7-7  
Weekday alarm  
1. Press and hold down the Alarm 1 or Alarm 2 buttons (depending  
on which alarm you wish to set day for).  
2
2. Whilst holding down Alarm 1 or Alarm 2 buttons repeatedly press  
1
and release the Alarm Days button until display shows 1-5.  
3. The alarm will sound every day at the preset time for 1 hour. To  
switch off the alarm until the next day press the On/off button.  
4. To switch off the alarms permanently press and hold down the  
Alarm 1 or Alarm 2 button. Whilst holding down the Alarm 1 or  
Alarm 2 button repeatedly press the Alarm mode button until  
the display shows  
.
9
Download from Www.Somanuals.com. All Manuals Search And Download.  
Weekend alarm  
1. Press and hold down the Alarm 1 or Alarm 2 buttons (depending  
on which alarm you wish to set day for).  
2. Whilst holding down Alarm 1 or Alarm 2 buttons repeatedly press  
2
and release the Alarm days button until display shows 6-7.  
1
3. The alarm will sound on Saturday and Sunday at the preset time for  
1 hour. To switch off the alarm until the next day press the On/off  
button.  
4. To switch off the alarms permanently press and hold down the  
Alarm 1 or Alarm 2 button. Whilst holding down the Alarm 1 or  
Alarm 2 button repeatedly press the Alarm mode button until  
the display shows  
.
Everyday alarm  
1. Press and hold down the Alarm 1 or Alarm 2 buttons (depending  
on which alarm you wish to set day for).  
2. Whilst holding down Alarm 1 or Alarm 2 buttons repeatedly press  
2
1
and release the Alarm days button until display shows 1-7.  
3. The alarm will sound at the preset time for 1 hour. To switch off the  
alarm until the next day press the On/off button.  
4. To switch off the alarms permanently press and hold down the  
Alarm 1 or Alarm 2 button. Whilst holding down the Alarm 1 or  
Alarm 2 button repeatedly press the Alarm mode button until  
the display shows  
.
If you need any further advice, please call our Technical Helpline on :-  
Download from Www.Somanuals.com. All Manuals Search And Download.  
10  
020 8758 0338 (Mon-Fri)  
Monday to Saturday alarm  
1. Press and hold down the Alarm 1 or Alarm 2 buttons (depending  
on which alarm you wish to set day for).  
2
1
2. Whilst holding down Alarm 1 or Alarm 2 buttons repeatedly press  
and release the Alarm days button until display shows 1-6.  
3. The alarm will sound at the preset time for 1 hour. To switch off the  
alarm until the next day press the On/off button.  
4. To switch off the alarms permanently press and hold down the  
Alarm 1 or Alarm 2 button. Whilst holding down the Alarm 1 or  
Alarm 2 button repeatedly press the Alarm mode button until  
the display shows  
.
Sunday only alarm  
1. Press and hold down the Alarm 1 or Alarm 2 buttons (depending  
on which alarm you wish to set day for).  
1
2
2. Whilst holding down Alarm 1 or Alarm 2 buttons repeatedly press  
and release the Alarm days button until display shows 7-7.  
3. The alarm will sound at the preset time for 1 hour. To switch off the  
alarm until the next day press the On/off button.  
4. To switch off the alarms permanently press and hold down the  
Alarm 1 or Alarm 2 button. Whilst holding down the Alarm 1 or  
Alarm 2 button repeatedly press the Alarm mode button until  
the display shows  
.
11  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Checking alarm times  
1. Press and hold down either Alarm 1 or Alarm 2 buttons depending  
which alarm you want to check. The display will change from normal  
time to alarm time. Release the Alarm 1 or Alarm 2 buttons to  
return to normal time. To adjust the alarm time refer to instructions  
on pages 8 - 9.  
1
Checking alarm mode  
1. Press and hold down either Alarm 1 or Alarm 2 buttons depending  
which alarm you want to check.  
2
1
2. Whilst holding down Alarm 1 or Alarm 2 buttons press the Alarm  
mode button. The display will change from normal time to alarm  
mode. Release the buttons to return to normal time. To adjust the  
alarm mode refer to instructions on pages 8 - 9.  
If you need any further advice, please call our Technical Helpline on :-  
12  
Download from Www.Somanuals.com. All Manuals Search And Download.  
020 8758 0338 (Mon-Fri)  
Snooze control  
1. The radio or buzzer alarm can be silenced for approximately 9  
minutes by pressing the Snooze button. This sequence can be  
repeated during the 60 minute alarm period.  
1
Sleep timer  
2
You can program your clock radio to play the radio for up to 90 minutes  
and then switch off.  
1
1. Press the Sleep button. The display will show the sleep time.  
2
2. To increase or decrease the amount of time the radio will play before  
switching off, hold down the Sleep button and increase or  
decrease the sleep time using the Up or Down buttons (maximum  
90 minutes - minimum 2 minutes).  
3. To cancel the sleep timer before the sleep time has elapsed press  
the Snooze or On/Off buttons.  
3
3
13  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Listening to the radio  
1. Switch on the radio by pressing the On/Off button.  
2. Select the required waveband using the Waveband switch.  
3. Tune in to the desired station using the Tuning control.  
4. Adjust volume using the Volume control.  
1
2
5. The Wire aerial located on the rear of your clock radio is for FM  
reception. The wire should be fully extended and positioned for  
optimum reception.  
For MW reception there is a built in ferrite aerial. Rotate your clock  
radio to the position giving best reception.  
3
4
6. To switch off press the On/Off button.  
6
If you need any further advice, please call our Technical Helpline on :-  
14  
Download from Www.Somanuals.com. All Manuals Search And Download.  
020 8758 0338 (Mon-Fri)  
Dimmer switch  
The Dimmer switch on your clock radio will allow you to adjust the  
intensity of the clock display to suit room brightness.  
1
1. Use the High or Low buttons to adjust the intensity of the display.  
1
Back-up battery  
As with all batteries, eventually the built in lithium battery will need to be  
replaced. A number of factors, such as the length of time between the  
date your clock radio was manufactured and the date you plugged it in  
for the first time, determine the amount of time before battery replacement.  
During this initial storage period the lithium backup battery is supplying  
power to your clock radio’s computer memory. Once you connect your  
clock radio to the household AC mains supply the battery no longer  
supplies power to your clock radio’s computer memory. A fresh backup  
battery can supply power to your clock radio’s computer memory for 3  
years even if it is never connected to a mains supply. If your clock radio  
was connected to the AC mains supply within a few months after it was  
manufactured and you experience only short interruptions to the mains  
supply, your battery may last for up to 5 years or even longer.  
When the battery drops below a certain level the Low battery indicator  
will light. When you see this indicator you should change the battery as  
soon as it is convenient to do so.  
See following page for details on battery replacement.  
15  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Changing the back-up battery  
1. Purchase a replacement lithium backup battery type CR2032 or  
equivalent.  
2. Remove the new battery from its packaging so that it is ready to  
install.  
3. Important: Maintain connection to AC mains supply during battery  
replacement. This will provide power whilst the original battery is  
removed.  
4. Use a small screwdriver to remove the small screw securing the  
battery holder on cabinet base.  
5. Remove the battery holder from cabinet.  
6. Remove old battery from holder. Replace new battery with  
facing direction shown in drawing opposite.  
sign  
+
4
7. Replace the holder into cabinet back.  
8. Refit the small screw to secure holder.  
9. Check that the 'Battery low' indicator is not lit.  
9
If you need any further advice, please call our Technical Helpline on :-  
Download from Www.Somanuals.com. All Manuals Search And Download.  
16  
020 8758 0338 (Mon-Fri)  
Time Zones  
Your clock radio is set to UK time zone 12 GMT (UTC). Should you wish  
to take your clock radio to other countries the time zone will need to be  
reset.  
1. Press and hold down the Alarm mode button - the display will  
show the time zone currently selected e.g. 12.  
1
2. Whilst holding down the Alarm mode button adjust the time zone  
using the Up or Down buttons. See following table for details of  
time zones and their offsets relative to GMT.  
Zone  
12  
Offset (Hours)  
Zone  
00  
Offset (Hours)  
GMT +/-12  
GMT 0  
GMT -1  
GMT -2  
GMT -3  
GMT -4  
GMT -5  
GMT -6  
GMT -7  
GMT -8  
GMT -9  
13  
01  
GMT +11  
GMT +10  
GMT +9  
GMT +8  
GMT +7  
GMT +6  
GMT +5  
GMT +4  
GMT +3  
GMT +2  
GMT +1  
14  
02  
15  
03  
16  
04  
17  
05  
18  
06  
2
19  
07  
20  
08  
21  
09  
2
22  
GMT -10  
GMT -11  
10  
23  
11  
17  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Specifications  
Power Requirements  
Mains  
Circuit features  
Loudspeaker  
8 ohms  
AC 230 volts, 50Hz  
only  
Back-up Battery  
1 x CR2032 Lithium (3 - 5 year life)  
Output power 180mW  
Frequency Coverage  
Aerial System  
FM  
Wire Aerial  
FM  
87.5 - 108MHz  
515 - 1635 kHz  
MW  
MW  
Built-in Ferrite aerial  
The Company reserves the right to amend the specification without notice.  
If you need any further advice, please call our Technical Helpline on :-  
Download from Www.Somanuals.com. All Manuals Search And Download.  
18  
020 8758 0338 (Mon-Fri)  
General  
Fuse  
Do not allow this unit to be exposed to moisture (e.g. dripping or  
splashing) or to temperatures exceeding 70 degrees centigrade. It is  
recommended that the FM band be used wherever possible as better  
results in terms of quality and freedom from interference will usually be  
obtained than on the MW band.  
This apparatus must be protected by a 3A fuse (BS1362) in a 13A plug  
(BS1363). If another type of plug is used a 5A fuse should be fitted in  
the plug, adaptor or distribution board.  
IFINDOUBT-CONSULTAQUALIFIEDELECTRICIAN.  
Mains supply  
The CR9977 will operate from a supply of AC 230volts, 50Hz  
only.  
For your convenience this product is supplied with a plug which is fitted  
with a fuse of the appropriate rating. If the plug supplied is not suitable  
for your socket outlet, it should be removed by unscrewing the plug top,  
the terminal screws, and removing the cable.  
The correct style of plug to suit your household together with a correctly  
rated fuse should be fitted.  
IFINDOUBT-CONSULTAQUALIFIEDELECTRICIAN  
IMPORTANT. DO NOT make any connection to the larger terminal which  
is marked with the letter E or by the safety earth symbol  
Green or Green-and-yellow.  
or coloured  
The wires in the mains lead are coloured in accordance with the  
following codes :-  
BLUE - NEUTRAL  
BROWN - LIVE  
As these colours may not correspond with the coloured markings  
identifying the terminals in your plug, proceed as follows:-  
The wire coloured BLUE must be  
connected to the terminal marked N  
or coloured BLACK.  
The wire coloured BROWN must be  
connected to the terminal marked L  
or coloured RED.  
19  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Notes:  
If you need any further advice, please call our Technical Helpline on :-  
20  
Download from Www.Somanuals.com. All Manuals Search And Download.  
020 8758 0338 (Mon-Fri)  
Notes:  
21  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Guarantee  
This instrument is guaranteed for twelve months from the date of delivery to the original owner against failure due to faulty workmanship or component  
breakdown, subject to the procedure stated below. Should any component or part fail during this guarantee period it will be repaired or replaced  
free of charge.  
The guarantee does not cover:  
1. Damage resulting from incorrect use.  
2. Consequential damage.  
3. Receivers with removed or defaced serial numbers.  
Procedure:  
Any claim under this guarantee should be made through the dealer from whom the instrument was purchased. It is likely that your Roberts' dealer  
will be able to attend to any defect quickly and efficiently but should it be necessary the dealer will return the instrument to the Company’s service  
department for attention. In the event that it is not possible to return the instrument to the Roberts' dealer from whom it was purchased, please  
contact Roberts Radio Technical Services at the address shown on the rear of this manual.  
These statements do not affect the statutory rights of a consumer.  
If you need any further advice, please call our Technical Helpline on :-  
Download from Www.Somanuals.com. All Manuals Search And Download.  
22  
020 8758 0338 (Mon-Fri)  
ROBERTS RADIO TECHNICAL SERVICES  
97-99 Worton Road  
Isleworth Middlesex  
TW7 6EG  
Technical Helpline:- 020 8758 0338 (Mon-Fri)  
Issue 2  
Download from Www.Somanuals.com. All Manuals Search And Download.  

Q Logic MP3 Player Accessories SN0054651 00 F User Guide
Radio Shack Universal Remote 6 IN ONE TOUCHSCREEN REMOTE User Guide
ResMed Sleep Apnea Machine S9 AutoSet User Guide
RIDGID Saw TS 2400 User Guide
Rolls Musical Instrument Rm203x User Guide
Samsung Car Stereo System MAX ZS720 User Guide
Sanus Systems Indoor Furnishings LC2A User Guide
Sanyo Digital Camera VCC HD4000 User Guide
Sanyo MP3 Player DMP M600 User Guide
Sennheiser Battery Charger SZL1011 User Guide