M38517T-ADS
Temporary Target Board for M38507ARLSS and M38517RSS
User's Manual
Rev.1.00
September 1, 2003
REJ10J0340-0100Z
Download from Www.Somanuals.com. All Manuals Search And Download.
Contents
1. Things to Check When Unpacking.....................................................................................4
2. Outline ................................................................................................................................4
3. Specifications .....................................................................................................................4
4. Setting Up ...........................................................................................................................5
4.1 Mounting an Emulator MCU ................................................................................5
4.2 Connecting the Emulation Pod..............................................................................6
4.3 Setting the Switches ..............................................................................................7
5. Oscillator Circuit ................................................................................................................8
5.1 Oscillator Circuit Board ........................................................................................8
5.2 32.768kHz Oscillator Circuit ................................................................................8
6. Reset Circuit .......................................................................................................................9
7. Pin Layout ........................................................................................................................10
( 3 / 12 )
Download from Www.Somanuals.com. All Manuals Search And Download.
1. Things to Check When Unpacking
The M38517T-ADS package consists of the following products. When unpacking your package,
check to see that all of these components are included.
Table 1.1 Package components
Content
Temporary target board
User's manual
M38517T-ADS
M38517T-ADS User's manual (English/Japanese)
* If you find any item missing or faulty, or any suggestion, contact your local distributor.
2. Outline
The M38517T-ADS is a temporary target board used to develop software with a PC4701 emulator
system. It supplies to the emulator MCU the minimum required signals needed to operate the
emulator MCU, including power supply voltage, clock signals and reset signals. Use it when the
target system is not ready.
3. Specifications
Table 3.1 lists specifications of the M38517T-ADS.
Table 3.1 Specifications of the M38517T-ADS
Item
Content
Applicable MCU
Clock
M38507ARLSS, M38517RSS
4.0MHz oscillator mounted (oscillator circuit board OSC-2 used)
32.768 kHz (can be disconnected by SW1)
Power supply voltage
RESET
2.7 V to 5.5 V (supplied separately*)
• Reset circuit mounted (power-on reset and reset switch)
• Connects the reset output of an emulation pod
External dimensions
Width
Depth
90 mm
115 mm
Others
Universal part prepared
* Power cannot be supplied from the emulation pod for PC4701 (e.g. M38000TL2-FPD). A
separate power supply is needed.
( 4 / 12 )
Download from Www.Somanuals.com. All Manuals Search And Download.
4. Setting Up
This chapter describes how to set up the M38517T-ADS.
CAUTION
Note on Setting Up:
• Always shut OFF power before connecting this product. The power ON state could
destroy internal circuits.
4.1 Mounting an Emulator MCU
Mount an emulator MCU on the M38517T-ADS. After checking the position of the No. 1 pin of the
emulator MCU, mount the emulator MCU referencing Figure 4.1.
Figure 4.1 Position of No. 1 pin of an M38517T-ADS's emulator MCU
( 5 / 12 )
Download from Www.Somanuals.com. All Manuals Search And Download.
4.2 Connecting to the Emulation Pod
(1) Insert the connector on the tip of the emulation pod probe to the socket on the emulator MCU.
(2) Connect the cables of the M38000TL2-PSW2 as shown in Table 4.1 depending on the emulator
MCU you use.
Do not connect the Vcc cable (yellow) to pin Vcc (TP1).
Table 4.1 Connector cables of the M38000TL2-PSW and applicable signals
Cable color
White
Signal
RESET
Vss
For M38507ARLSS
For M38517RSS
TP3
TP3
TP2
TP1
Black
TP2
Yellow
Vcc
No connection
(3) Set the MCU type selection switch (SW1) of the M38000TL2-FPD as shown in Table 4.2.
Table 4.2 Settings of the SW1 of the M38000TL2-FPD
M38507ARLSS
RLSS/RLFS
M38517RSS
RSS/RFS
M38000TL2-FPD SW1
(4) Connect a power supply (not included) to pin Vcc (TP1) of the M38517T-ADS. And connect the
GND output of the power supply to pin Vss (TP2). Use the power supply whose rising time is 10
ms or less.
Figure 4.2 Connecting the M38507ARLSS
( 6 / 12 )
Download from Www.Somanuals.com. All Manuals Search And Download.
Figure 4.3 Connecting the M38517RSS
4.3 Setting the Switches
Set the switches SW1 to SW3 according to your applications. Table 4.3 describes the functions of
the switches SW1 to SW3.
Table 4.3 Functions of the switches SW1, SW2 and SW3
No.
Name
Factory-setting
PORT
Function
SW1
PORT/XCIN
Allows you to choose whether to supply the sub-clock
signals (32.768 kHz) to the MCU's XCIN pin (pin 16).
To use pin P21/XCIN as an I/O port, choose the PORT
side.
To use the sub-clock signals, choose the XCIN side.
SW2
SW3
VREF
Vcc
Vss
Allows you to choose whether to apply Vcc or some
other source to the MCU's VREF pin (pin 2). In the
case of the latter, choose the J1-2 side, and apply a
voltage within a prescribed range to the J1-2.
CNVss
Allows you to choose which to connect, Vcc or Vss, to
the MCU's CNVss (pin 15).
( 7 / 12 )
Download from Www.Somanuals.com. All Manuals Search And Download.
5. Oscillator Circuit
5.1 Oscillator Circuit Board
The M38517T-ADS has a built-in oscillator circuit board on which a 4.0MHz oscillator is mounted.
Figure 5.1 shows an external view of the OSC-2 oscillator circuit board (bare board) and where
connector pins are located. Figure 5.2 shows the circuitry of the OSC-2 oscillator circuit board (bare
board). Use the number of oscillator circuits recommended by the oscillator manufacturer.
J1-4: GND
J1-3: Oscillator output
J1-2: GND
J1-1: VCC (5 V)
Bypass capacitor
Figure 5.1 External view of the oscillator board (OSC-2) and connector pin assignment
IC1
IC1
CLK
11
10
9
8
J1-3
J1-1
R1
Vcc
1
2
*
*
R2
X1 ,X2
14
IC1
3
5
4
6
C3
7
J1-2
J1-4
C2
C1
13
12
GND
GND
*
X3
IC1
* X1: 5.08-mm-pitch 2-pin oscillator
* X2: 2.54-mm-pitch 2-pin oscillator
* X3: 2.54-mm-pitch 3-pin oscillator
IC1: Inverter (Unbuffer)
Figure 5.2 Circuit of the oscillator board (OSC-2)
5.2 32.768kHz Oscillator Circuit
The 32.768kHz oscillator circuit is prepared on the M38517T-ADS. When using the 32.768kHz
oscillator circuit as a sub-clock, set the short-circuit connector of the SW1 to the XCIN side.
( 8 / 12 )
Download from Www.Somanuals.com. All Manuals Search And Download.
6. Reset Circuit
Figure 6.1 shows the reset circuit and its waveform. In this product, reset is cleared in about 100 ms
from the instant Vcc passes about 2.1 V after having started from 0 V. When Vcc drops down to about
2.1 V, reset turns effective.
Detected power voltage (V)
About 1
Figure 6.1 Reset circuit and its waveform
By using the switch SW4, the MCU can be reset manually.
Table 6.1 Function of SW4 (reset switch)
No.
Name
Function
SW4
RESET
This is the reset switch. Press down this switch to reset the MCU.
( 9 / 12 )
Download from Www.Somanuals.com. All Manuals Search And Download.
7. Pin Layout
Figure 7.1 shows the pin layout of the M38517T-ADS.
Figure 7.1 Pin layout of the M38517T-ADS
( 10 / 12 )
Download from Www.Somanuals.com. All Manuals Search And Download.
M38517T-ADS User's Manual
Rev.1.00
September 1, 2003
REJ10J0340-0100Z
COPYRIGHT ©2003 RENESAS TECHNOLOGY CORPORATION
AND RENESAS SOLUTIONS CORPORATION ALL RIGHTS RESERVED
Download from Www.Somanuals.com. All Manuals Search And Download.
Download from Www.Somanuals.com. All Manuals Search And Download.
|