Renesas Network Card M30200T RPD E User Guide

M30200T-RPD-E  
Emulation Pod forM16C/20 Series  
User's Manual  
Rev.1.00  
September 1, 2003  
REJ10J0264-0100Z  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Preface  
The M30200T-RPD-E is an emulation pod main unit for M16C/20 Series of Renesas 16-bit  
microcomputers. The M30200T-RPD-E is used by connecting to the pod probe M302xxT-PRB and  
the PC4701 emulator main unit, and is controlled by the emulator debugger.  
This manual mainly explains specifications and setting up of the M30200T-RPD-E. For detail  
information about the pod probe, the PC4701 emulator main unit and the emulator debugger, refer  
to each user's manual.  
To check the components of this product, refer to "Things to Check When Unpacking" in this manual.  
If there is any question or doubt about this product, contact your local distributor.  
To use the product properly  
Precautions for Safety:  
• Both in this User's Manual and on the product itself, several icons are used to insure  
proper handling of this product and also to prevent injuries to you or other persons,  
or damage to your properties.  
• The icons' graphic images and meanings are given in Chapter 1 Precautions for  
Safety. Be sure to read this chapter before using the product.  
( 3 / 32 )  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Contents  
Summary.................................................................................................................................6  
Terminology ...........................................................................................................................7  
Things to Check When Unpacking.........................................................................................8  
Chapter 1. Precautions for Safety ...........................................................................................9  
1.1 Safety Symbols and Meanings ..............................................................................9  
Warning for Installation .................................................................................10  
Warning for Use Environment.......................................................................10  
WARNING  
CAUTION Caution to be Taken for Modifying This Product..........................................10  
Cautions to be Taken for This Product ..........................................................10  
IMPORTANT Notes on PC4701 Emulator Main Units ........................................................11  
Note on Abnormal Operation of PC4701 System .........................................11  
Notes on the Target System ...........................................................................11  
Notes on Connecting Pod Probe and Pitch Converter Board ........................12  
Note on Starting Up the Emulator System.....................................................12  
Note on Reset Input from the Target System ................................................12  
Note on Address 0 Access .............................................................................13  
Note on Differences between Actual MCU and Emulator ............................13  
Note on Referencing and Setting the Work Area ..........................................13  
Notes on MAP References and Settings ........................................................13  
Note on Changing Settings of the Memory Area ..........................................13  
Note on Stack .................................................................................................14  
Note on BRK Instruction ...............................................................................14  
Note on Software Break and Hardware Break...............................................14  
Notes on Using Address-match Interrupts .....................................................14  
Note on Software Reset .................................................................................14  
Note on Stop and Wait Modes .......................................................................14  
Note on Watchdog Function ..........................................................................14  
Chapter 2. Introduction.........................................................................................................15  
Chapter 3. Specifications ......................................................................................................16  
Chapter 4. Setting Up ...........................................................................................................17  
4.1 Removing the Upper Cover ................................................................................17  
4.2 Setting Oscillation Frequency .............................................................................18  
Chapter 5. Connection ..........................................................................................................22  
5.1 Connection to the Emulator Main Unit ...............................................................22  
5.2 Connection to the Emulation Pod .......................................................................23  
5.3 Connection to the Pod Probe ...............................................................................24  
( 4 / 32 )  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Chapter 6. External Dimensions ...........................................................................................25  
Chapter 7. Maintenance and Warranty .................................................................................27  
7.1 Maintenance ........................................................................................................27  
7.2 Warranty..............................................................................................................27  
7.3 Repair Provisions ................................................................................................27  
7.4 How to Request for Repair..................................................................................28  
Chapter 8. Troubleshooting ..................................................................................................29  
( 5 / 32 )  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Summary  
Chapter 1. Precautions for Safety  
This chapter describes the precautions which should be taken in order to use M30200T-RPD-E safely  
and properly. Refer to each manual of the pod probe, the emulator main unit and the emulator  
debugger for their precautions.  
Chapter 2. Introduction  
This chapter provides the system configuration and overview of M30200T-RPD-E.  
Chapter 3. Specifications  
This chapter lists the product specifications of M30200T-RPD-E.  
Chapter 4. Setting Up  
This chapter describes how to set up the M30200T-RPD-E hardware according to your system.  
Chapter 5. Connection  
This chapter describes how to connect the M30200T-RPD-E, emulator main unit and pod probe. For  
connection between the host machine and emulator main unit, connection between the pod probe and  
the target system, and installation of the emulator debugger, refer to each user's manual of the  
products.  
Chapter 6. External Dimensions  
This chapter shows the external dimensions of M30200T-RPD-E and its probe.  
Chapter 7. Maintenance and Warranty  
This chapter describes maintenance and warranty of M30200T-RPD-E.  
Chapter 8. Troubleshooting  
This chapter describes what to do when the emulation pod main unit does not work properly.  
( 6 / 32 )  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Terminology  
Some specific words used in this User's Manual are defined as follows:  
Emulator system  
This means an emulator system built around a PC4701 emulator. The PC4701 emulator system is  
configured with the emulator main unit, emulation pod main unit, pod probe, host machine, and  
emulator debugger.  
Emulator main unit PC4701  
This means a generic name for emulators for 8 and 16-bit MCUs. For details on specific models of  
Emulation pod main unit  
This means M30200T-RPD-E (this product). This emulation pod main unit is for M16C/20 series  
MCUs.  
Pod probe  
This means a pod probe equipped with an MCU for each group of M16C/20 Series.  
Host machine  
This means a personal computer used to control the emulator and emulation pod.  
Emulator debugger  
This means the following software tool to control the emulator from the host machine through an  
interface (serial, parallel, LPT parallel or LAN).  
Emulator debugger M3T-PD30 V.4.00 or later  
Firmware  
This means a program that analyzes contents of communication with the emulator debugger and  
controls the emulator hardware. The emulator contains an EEPROM. You can download from the  
emulator debugger when upgrading the version of the firmware itself or when handling another  
MCU.  
Target MCU  
This means the microcomputer you are going to debug.  
Target system  
This means a user's application system using the microcomputer to be debugged.  
( 7 / 32 )  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Things to Check When Unpacking  
The M30200T-RPD-E consists of the following parts and manuals. When unpacking, check to see  
if your M30200T-RPD-E package contains all of these items.  
Type name  
M30200T-RPD-E  
FLX120-RPD  
FLX64-PRB  
Description  
Emulation pod main unit  
Quantity  
1
1
1
1
1
1
1
Flexible cable for connecting PC4701 emulator  
Pitch converter board for connecting the pod probe (pre-installed)  
Oscillator circuit board (pre-installed)  
Oscillator circuit board (pre-installed)  
Oscillator circuit bare board  
OSC-3 (10 MHz)  
OSC-2 (32 MHz)  
OSC-2  
M30200T-RPD-E  
English user's manual (this manual)  
English user's manual  
M30200T-RPD-E  
Japanese user's manual  
1
Japanese user's manual  
Please keep the M30200T-RPD-E’s packing box and cushion material in your place for reuse at a later  
time when sending your product for repair or other purposes. Always use these packing box and  
cushion material when transporting the products.  
If any of these items are missing or found faulty, please contact your local distributor. Also, if there  
is any question or doubt about the packaged product, contact your local distributor.  
Other tool products required for this product:  
• Emulator main unit: PC4701 (essential)  
• Pod probe with an MCU for M16C/20 Series: M302xxT-PRB (essential)  
• Emulator debugger: M3T-PD30 (essential)  
• PROM programming adapter: PCA7302xxx-xx  
To purchase the products listed above, contact your local distributor.  
( 8 / 32 )  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Chapter 1. Precautions for Safety  
In both the user's manual and on the product itself, several icons are used to insure proper handling  
of this product and also to prevent injuries to you or other persons, or damage to your properties.  
This chapter describes the precautions which should be taken in order to use this product safely and  
properly. Be sure to read this chapter before using this product.  
1.1 Safety Symbols and Meanings  
If the requirements shown in the "WARNING"  
sentences are ignored, the equipment may  
cause serious personal injury or death.  
WARNING  
If the requirements shown in the "CAUTION"  
sentences are ignored, the equipment may  
malfunction.  
CAUTION  
It means important information on using this  
product.  
IMPORTANT  
In addition to the three above, the following are also used as appropriate.  
means WARNING or CAUTION.  
Example:  
CAUTION AGAINST AN ELECTRIC SHOCK  
means PROHIBITION.  
Example:  
DISASSEMBLY PROHIBITED  
means A FORCIBLE ACTION.  
Example:  
UNPLUG THE POWER CABLE FROM THE RECEPTACLE.  
The following pages describe the symbols "WARNING", "CAUTION", and "IMPORTANT".  
( 9 / 32 )  
Download from Www.Somanuals.com. All Manuals Search And Download.  
WARNING  
Warning for Installation:  
• Do not set this product in water or areas of high humidity. Make sure that the emulation pod main  
unit does not get wet. Spilling water or other liquids into the emulation pod main unit can cause an  
unrepairable damage.  
Warning for Use Environment:  
• The emulation pod main unit is air-cooled with the ventilation slot. Therefore, do not block the  
ventilation slot. When heated to high temperatures, the emulation pod main unit may not work  
properly.  
• This equipment is to be used in an environment with a maximum ambient temperature of 35°C. Care  
should be taken that this temperature is not exceeded.  
CAUTION  
Caution to be Taken for Modifying This Product:  
• Do not disassemble or modify this product. Disassembling or modifying this product can cause  
damage. Disassembling and modifying the product will void your warranty.  
Cautions to be Taken for This Product:  
• Use caution when handling the emulation pod main unit. Be careful not to apply a mechanical  
shock.  
• Do not touch directly the connector pins of the emulator main unit or the target MCU connector pins  
with your hand.  
• Do not pull the emulation pod main unit by the FLX120-RPD flexible cable or the FLX64 flexible  
cable.  
• The flexible cables FLX120-RPD and FLX64 are different from earlier models. The slits make  
them more flexible. However, excessive flexing or force may break conductors.  
• Do not use inch-size screws for this equipment. The screws used in this equipment are all ISO  
(meter-size) type screws. When replacing screws, use same type screws as used on the equipment.  
( 10 / 32 )  
Download from Www.Somanuals.com. All Manuals Search And Download.  
IMPORTANT  
Notes on PC4701 Emulator Main Units:  
• EMI standards are not met when this product is used with the PC4700H or PC4700L emulator main  
unit.  
• The PC4700H emulator main units whose serial number ends with a number cannot be used with  
M30200T-RPD-E. Use only products whose serial number ends with a letter of the alphabet. The  
serial number is on the bottom of the PC4700H.  
Example: 5KE100 .......... Can NOT be used with M30200T-RPD-E. Requires an upgrade.  
Example: 5LE123B ........ Can be used with M30200T-RPD-E.  
• Do not turn off the power when downloading firmware. If the emulator is powered off in the middle  
of the process, it will become unable to start up normally. In cases when the power is inadvertently  
shut off, re-execute downloading.  
Note on Abnormal Operation of PC4701 System:  
• If the PC4701 system does not pass all self-checks (excluding when an target system error occurs),  
there is the possibility of trouble in the system. In such case, contact the place of purchase. (Self-  
check should be executed when the target system is not connected.)  
• If the emulator main unit malfunctions due to external interference or some other causes, follow  
the steps given below.  
(1) Press the system reset switch located on the front panel of the emulator main unit.  
(2) If the emulator does not return to the normal operation despite the step (1) above, turn off the  
power source of the emulator main unit, turn it on again.  
Notes on the Target System:  
• Because the emulation pod main unit does not have the capacity to supply power to other devices,  
design your system so that the emulator MCU is powered by the target system.  
• Make sure that the target's supply voltage is 2.7 to 5 V.  
• Before turning on power to anything, check the host machine, emulator main unit, emulation pod  
main unit, pod probe, converter board and user's target system are properly connected. As  
explained here following, activate power to units as simultaneously as possible. Reverse the  
procedure to turn them off.  
(1) Turn on the target system.  
(2) Turn on the emulator main unit.  
( 11 / 32 )  
Download from Www.Somanuals.com. All Manuals Search And Download.  
IMPORTANT  
Notes on Connecting Pod Probe and Pitch Converter Board:  
• Prepare the right pod probe for your MCU. Without a pod probe this product cannot be used.  
• When connecting the pod probe and the pitch converter board, be careful not to forcibly press the  
connector top of the converter board. (The flexible cable and the converter board are guaranteed  
for only 20 insertion/removal iterations.)  
• Especially be careful not to insert the converter board in the wrong direction.  
Note on Starting Up the Emulator System:  
• Check the emulator starts up properly from the target status LEDs on the front panel of the emulator  
main unit itself.  
When power is received from the target system: ... The POWER target status is ON.  
When the clock starts oscillating:........................... The CLOCK target status is ON.  
When the reset is released: ..................................... The RESET target status is OFF.  
If the LEDs behave as described above within approximately 5 seconds of turning ON the power,  
the emulator has started up properly.  
Notes on Reset Input from the Target System:  
• The reset input from the target system is accepted only during program execution (while the RUN  
signal LED on the PC4701 is lit).  
( 12 / 32 )  
Download from Www.Somanuals.com. All Manuals Search And Download.  
IMPORTANT  
Note on Address 0 Access:  
• With the M16C/20 series MCU, when a maskable interrupt is generated, the interrupt data  
(interrupt No. and interrupt request level) stored in address 0 is read out. Also, the interrupt request  
bit is cleared when address 0 is read out. Consequently, when the address 0 read-out instruction is  
executed or when address 0 is read out in the cause of a program runaway, a malfunction occurs  
in that the interrupt is not executed despite the interrupt request, because the request bit of the  
highest priority interrupt factor enabled is cleared.  
Note on Differences between Actual MCU and Emulator:  
• Emulator operation differs from mask MCU operation, as listed below:  
(1) Initial values of internal resource data at power-on  
(2) Internal ROM and RAM capacities, etc.  
(3) A/D converter  
A/D converter characteristics differ from actual MCU characteristics because the flexible  
cable and other elements are used between the emulation MCU and target system.  
Note on Referencing and Setting the Work Area:  
• The work area given below is assigned as the initial setting at the time of starting up the emulator  
debugger.  
02C0016 to 02C0F16: Work area  
Notes on MAP References and Settings:  
• When starting up M30200T-RPD-E, initial MAP settings are as follows.  
0000016 to 003FF16: EXT  
0040016 to FFFFF16: INT  
• Always set the SFR area to EXT (external).  
Note on Changing Settings of the Memory Area:  
• To debug an MCU different in memory capacity, be sure to modify the settings in the memory area  
before using the MCU. For memory maps of respective MCUs, see the MCU User's Manual.  
( 13 / 32 )  
Download from Www.Somanuals.com. All Manuals Search And Download.  
IMPORTANT  
Note on Stack:  
• This product uses up to 8 bytes for stack.  
Note on BRK Instruction:  
• BRK instruction cannot be used.  
Note on Software Break and Hardware Break:  
• A software break and a hardware break cannot be used simultaneously. If they are used  
simultaneously, the emulation pod main unit may not work properly.  
Notes on Using Address-match Interrupts:  
• Do not set software breaks at the same addresses as address-match interrupts as the program may  
run out of control.  
• Do not set a hardware break within 4 instructions before an address at which an address-match  
interrupt occurs. If you do set a hardware break in this range, the program will run out of control.  
• When an address at which an address-match interrupt occurs is executed in one-step mode, the  
program stops after executing the first instruction after returning from the address-match interrupt  
processing.  
Note on Software Reset:  
• Do not use the software reset. It may not work properly.  
Note on Stop and Wait Modes:  
• Do not perform step execution at addresses in the stop or wait mode. It may cause communication  
errors.  
Note on Watchdog Function:  
• Debug functions such as a single step cannot be used while using the watchdog function. Only GO  
command (program execution) is possible. To use other debug functions, disable the watchdog  
function.  
( 14 / 32 )  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Chapter 2. Introduction  
M30200T-RPD-E is used by connecting to the PC4701 emulator main unit. Figure 2.1 shows the  
system configuration.  
Figure 2.1 System configuration  
Products (1) to (4) shown in Figure 2.1 are included with this product.  
(1) M30200T-RPD-E (Emulation pod main unit)  
This emulation pod main unit contains emulation memory and debugging functions.  
(2) FLX120-RPD (Flexible cable)  
This 120-pin flexible cable connects the PC4701 emulator main unit and emulation pod main unit.  
(3) FLX64 (Flexible cable)  
This 64-pin flexible cable connects the emulation pod main unit and pod probe.  
(4) FLX64-PRB (Pitch converter board)  
This board connects the 64-pin flexible board and pod probe.  
( 15 / 32 )  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Chapter 3. Specifications  
Table 3.1 lists the specifications of M30200T-RPD-E.  
Table 3.1 Specifications of M30200T-RPD-E  
Usable emulator main unit  
Usable MCU  
PC4701  
M16C/20 Series MCUs  
Single-chip mode  
1 MB  
Usable MCU mode  
Emulation memory  
Clock  
Xin: 10 MHz  
Xcin: 32.768 kHz  
Power supply range  
+2.7 to 5.5 V  
Up to 8 bytes  
Stack capacity used for emulator  
Suspended cycles in run-time debug  
16-byte dump: Approx. 312 BCLK cycle  
16-byte fill: Approx. 283 BCLK cycle  
Power supply to emulation pod  
1.Supplied from an emulator main unit  
2.The operating voltage of the emulation pod main unit is  
determined by detecting the supply voltage of the target  
system. When no target system is connected, or when  
the supply voltage of the target system is more than 5.0  
V, the operating voltage is 5.0 V.  
Operating temperature range  
Storage temperature range  
Overseas standards  
5 to 35°C (no dew)  
-10 to 60°C (no dew)  
(1) U.S. EMI standards (FCC part 15 Class A)  
(2) CE marking (EN55022, EN50082-1)  
( 16 / 32 )  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Chapter 4. Setting Up  
4.1 Removing the Upper Cover  
If you need to change the input frequency, remove the upper cover of the product to change the  
configuration.  
(1) Remove the four screws of both sides and lift off the upper cover. (see Figure 4.1)  
(2) Change the input frequency following the instructions shown below.  
(3) Replace the upper cover and tighten the four screws.  
Figure 4.1 Removing the upper cover  
Caution  
Before Removing the Upper Cover:  
• Always shut OFF power before removing the cover and changing the oscillator  
circuit board. Removing the cover and setting switches in the power ON state could  
destroy internal circuits.  
( 17 / 32 )  
Download from Www.Somanuals.com. All Manuals Search And Download.  
4.2 Setting Oscillation Frequency  
When you are using the emulation pod main unit's internal oscillator, see (1) below, and when you  
are using the target system's oscillator, see (2) on page 21.  
(1) Using emulation pod main unit's oscillator  
M30200T-RPD-E is available with two types of internal oscillator circuits:  
• OSC-3 oscillator circuit board (default when shipped): Xin = 10 MHz  
• OSC-2 oscillator circuit board (bare board)  
a. OSC-3 oscillator circuit board  
M30200T-RPD-E is equipped with a 10MHz internal oscillator circuit board (OSC-3). If  
you are running M30200T-RPD-E at 10 MHz, you can use the OSC-3 oscillator circuit  
board.  
b. OSC-2 oscillator circuit board  
M30200T-RPD-E is supplied with the OSC-2 oscillator circuit bare board (connector pin  
mounted).  
If you are using M30200T-RPD-E with internal oscillation frequencies other than 10  
MHz, create the desired oscillator circuit on the OSC-2 bare board and replace the OSC-  
3 board with the OSC-2 board.  
Figure 4.2 shows the external view and connector pin layout of the OSC-2 oscillator circuit  
board.  
J1-4: GND  
J1-3: Oscillator output  
J1-2: GND  
J1-1: Vcc  
Figure 4.2 External view of oscillator bare board OSC-2 and connector pin layout of OSC-2  
( 18 / 32 )  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Figure 4.3 shows the OSC-2 circuit. Use the circuit constants recommended by the  
manufacturer of the oscillator.  
IC1  
IC1  
CLK  
11  
10  
9
8
J1-3  
J1-1  
R1  
Vcc  
1
2
*
*
R2  
X1 ,X2  
14  
IC1  
3
5
4
6
C3  
7
J1-2  
J1-4  
C2  
C1  
13  
12  
GND  
GND  
*
X3  
IC1  
* X1: 5.08-mm-pitch 2-pin oscillator  
* X2: 2.54-mm-pitch 2-pin oscillator  
* X3: 2.54-mm-pitch 3-pin oscillator  
IC1: Inverter (Unbuffer)  
Figure 4.3 Circuit of oscillator board OSC-2  
( 19 / 32 )  
Download from Www.Somanuals.com. All Manuals Search And Download.  
How to replace the oscillator circuit board is shown in Figure 4.4 below.  
(1) Unscrew the screw securing the oscillator circuit  
board.  
(2) Lift off the OSC-3 board.  
(3) Mount the J1 connector of the OSC-2 board into the  
J5 connector of the M30200T-PRT board.  
(4) Secure the OSC-2 board with the screw.  
Figure 4.4 Replacing small oscillator circuit boards  
( 20 / 32 )  
Download from Www.Somanuals.com. All Manuals Search And Download.  
(2) Using target system's oscillator  
a. To operate the emulator with an external clock, construct the oscillation circuit shown in  
Figure 4.5 in the target system and input the oscillation output at 40-60% duty into the Xin  
(Xcin) pin.  
b. Make note of the fact that in the oscillation circuit shown in Figure 4.6 where a resonator  
is connected between the Xin (Xcin) and Xout (Xcout) pins, oscillation does not occur  
because a flexible cable, buffer IC and other devices are used between the evaluation MCU  
and the target system.  
Figure 4.5 External oscillator circuit  
Figure 4.6 Circuit in which oscillation does not occur  
( 21 / 32 )  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Chapter 5. Connection  
5.1 Connection to the Emulator Main Unit  
Use the FLX120-RPD 120-pin flexible cable (included with the package) to connect the emulator  
main unit and M30200T-RPD-E. Figure 5.1 shows how to connect the emulator main unit and  
FLX120-RPD.  
Install the FLX120-RPD connector (emulator PC4701 side) on the cable connector of the PC4701.  
To insert the FLX120-RPD connector, hold the cover of the connector with the "UPSIDE" label  
facing up. Then fix the screws of the cover of the connector.  
Figure 5.1 Connecting emulator main unit and FLX120-RPD  
Caution  
Note on Connecting the Cable:  
• Be sure to turn off the power before making connections. Otherwise, the internal  
circuits may be damaged.  
( 22 / 32 )  
Download from Www.Somanuals.com. All Manuals Search And Download.  
5.2 Connection to the Emulation Pod  
Attach the FLX120-RPD to M30200T-RPD-E, then secure them with the screws. Figure 5.2 shows  
how to connect M30200T-RPD-E and FLX120-RPD.  
Figure 5.2 Connecting emulation pod and FLX120-RPD  
Caution  
Note on Connecting the Cable:  
• Be sure to turn off the power before making connections. Otherwise, the internal  
circuits may be damaged.  
( 23 / 32 )  
Download from Www.Somanuals.com. All Manuals Search And Download.  
5.3 Connection to the Pod Probe  
The emulation pod for M16C/20 Series consists of the M30200T-RPD-E emulation pod main unit  
and the M302xxT-PRB pod probe. Figure 5.3 shows how to connect the M302xxT-PRB pod probe.  
And Figure 5.4 shows how to remove it.  
(1) Attach the J1 and J2 connectors of M302xxT-PRB  
to the J3 and J4 connectors of FLX64-PRB respec-  
tively.  
(2) Secure the FLX64-PRB with the two screws.  
Figure 5.3 Connecting the M302xxT-PRB pod probe  
(1) Unscrew the two screws of M302xxT-PRB.  
(2) Lift off the M302xxT-PRB from the FLX64-PRB.  
Pull the M302xxT-PRB straight down, being care-  
ful not to break the connector.  
Figure 5.4 Removing the M302xxT-PRB pod probe  
Caution  
Note on Connecting the Cable:  
• Be sure to turn off the power before making connections. Otherwise, the internal  
circuits may be damaged.  
• The small connectors (J3 and J4) of M302xxT-PRB are guaranteed for only 20  
insertion/removal iterations.  
• The small connectors (J3 and J4) of FLX64-PRB and the small connectors (J1 and  
J2) of M302xxT-PRB are guaranteed for only 50 insertion/removal iterations.  
( 24 / 32 )  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Chapter 6. External Dimensions  
Figures 6.1 shows external dimensions of M30200T-RPD-E.  
Unit: mm  
Figure 6.1 External dimensions of M30200T-RPD-E  
( 25 / 32 )  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Figures 6.2 shows external dimensions of the FLX64-PRB pitch converter board for connecting to  
the pod probe.  
Unit: mm  
Figure 6.2 External dimensions of FLX64-PRB  
( 26 / 32 )  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Chapter 7. Maintenance and Guarantee  
7.1 Maintenance  
If dust or dirt collects on any equipment of your emulation system, wipe it off with a dry soft cloth.  
Do not use thinner or other solvents because these chemicals can cause the equipment's surface  
coating to separate.  
7.2 Guarantee  
If your product becomes faulty within twelve months after its purchase while being used under good  
conditions by observing "Precautions for Safety" described in Chapter 1 of this user's manual, we will  
repair or replace your faulty product free of charge. Note, however, that if your product's fault is raised  
by any one of the following causes, we will repair it or replace it with new one with extra-charge:  
• Misuse, abuse, or use under extraordinary conditions  
• Unauthorized repair, remodeling, maintenance, and so on  
• Inadequate user's system or misuse of it  
• Fires, earthquakes, and other unexpected disasters  
In the above cases, contact your local distributor. If your product is being leased, consult the leasing  
company or the owner.  
7.3 Repair Provisions  
(1) Repair with extra-charge  
The products elapsed more than twelve months after purchase can be repaired with extra-charge.  
(2) Replacement with extra-charge  
If your product's fault falls in any of the following categories, the fault will be corrected by  
replacing the entire product instead of repair, or you will be advised to purchase new one,  
depending on the severity of the fault.  
• Faulty or broken mechanical portions  
• Flaw, separation, or rust in coated or plated portions  
• Flaw or cracks in plastic portions  
• Faults or breakage caused by improper use or unauthorized repair or modification  
• Heavily damaged electric circuits due to overvoltage, overcurrent or shorting of power supply  
• Cracks in the printed circuit board or burnt-down patterns  
• Wide range of faults that makes replacement less expensive than repair  
• Unlocatable or unidentified faults  
(3) Expiration of the repair period  
When a period of twelve months elapses after the model was dropped from production, repairing  
products of the model may become impossible.  
(4) Transportation fees at sending your product for repair  
Please send your product to us for repair at your expense.  
( 27 / 32 )  
Download from Www.Somanuals.com. All Manuals Search And Download.  
7.4 How to Request for Repair  
If your product is found faulty, follow the procedure below to send your product for repair.  
Customer  
Distributor  
Fill in the Repair Request Sheet included with this product, then send it  
along with this product for repair to your local distributor. Make sure  
that information in the Repair Request Sheet is written in as much detail  
as possible to facilitate repair.  
After checking the contents of fault, the distributor should please send  
the faulty product along with the Repair Request Sheet to Renesas  
Solutions Corp.  
Renesas Solutions When the faulty product is repaired, it will be returned to the customer  
at the earliest convenience.  
CAUTION  
Note on Transporting the Product:  
• When sending your product for repair, use the packing box and cushion material supplied with this  
product when delivered to you and specify handling caution for it to be handled as precision  
equipment. If packing of your product is not complete, it may be damaged during transportation.  
When you pack your product in a bag, make sure to use conductive polyvinyl supplied with this  
product (usually a blue bag). When you use other bags, they may cause a trouble on your product  
because of static electricity.  
( 28 / 32 )  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Chapter 8. Troubleshooting  
When the M30200T-RPD-E does not work properly, check the items listed below.  
(1) The emulator main unit cannot be powered up.  
Check to see if the AC power cord is firmly plugged into the receptacle.  
Check to see if the AC power 3P-2P converting connector is firmly connected.  
(2) The M30200T-RPD-E does not start up when the target system is connected with the PC4701  
system. (The Error LED of the emulator main unit lights up.)  
Check (1) described above.  
Check whether the emulator main unit and the FLX120-RPD are firmly connected.  
Check whether the FLX120-RPD and the M30200T-RPD-E are firmly connected.  
Check whether the M30200T-RPD-E and the pod probe are firmly connected.  
Check whether the converter board and the target system are firmly connected.  
Check whether the power and GND are supplied to the target system.  
Check whether switches of the pod probe are properly set. (For details, refer to the user's manual  
of the pod probe.)  
Check whether the RESET pin is held 'HIGH' when the target system is connected.  
Check whether the oscillator circuit of the target system is oscillating correctly when using the  
oscillator of the target system.  
Check whether proper firmware is downloaded in the emulator main unit. (Refer to the user's  
manual of the emulator debugger about how to download firmware.)  
When the condition does not improve even if you check the items above, troubles described below  
are considered.  
(1) Trouble of the evaluation MCU  
(2) Trouble of the M30200T-RPD-E  
(3) Trouble of the PC4701 emulator main unit  
( 29 / 32 )  
Download from Www.Somanuals.com. All Manuals Search And Download.  
MEMO  
( 30 / 32 )  
Download from Www.Somanuals.com. All Manuals Search And Download.  
M30200T-RPD-E User's Manual  
Rev.1.00  
September 1, 2003  
REJ10J0264-0100Z  
COPYRIGHT ©2003 RENESAS TECHNOLOGY CORPORATION  
AND RENESAS SOLUTIONS CORPORATION ALL RIGHTS RESERVED  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Download from Www.Somanuals.com. All Manuals Search And Download.  

Radio Shack Cassette Player SCR 64 User Guide
Radio Shack Two Way Radio 21 1826 User Guide
Raypak Network Router Y 308 User Guide
RCA Projection Television P61310 User Guide
Reebok Fitness Home Gym RBTL111040 User Guide
Roland Musical Instrument G 70 User Guide
Royal Sovereign Binding Machine RBM 1200 User Guide
Ryobi Brush Cutter CS26 User Guide
Samsung Computer Monitor 153S User Guide
Samsung Stereo System P10 User Guide