M32182T2-PTC
Converter for In-circuit Connection (for M32182F3xFP)
Instruction Manual
Notes regarding these materials
• These materials are intended as a reference to assist our customers in the selection of the Renesas Technology product best suited to the customer's
application; they do not convey any license under any intellectual property rights, or any other rights, belonging to Renesas Technology Corporation, Renesas
Solutions Corporation or a third party.
• Renesas Technology Corporation and Renesas Solutions Corporation assume no responsibility for any damage, or infringement of any third-party's rights,
originating in the use of any product data, diagrams, charts, programs, algorithms, or circuit application examples contained in these materials.
• All information contained in these materials, including product data, diagrams, charts, programs and algorithms represents information on products at the
time of publication of these materials, and are subject to change by Renesas Technology Corporation and Renesas Solutions Corporation without notice
due to product improvements or other reasons. It is therefore recommended that customers contact Renesas Technology Corporation, Renesas Solutions
Corporation or an authorized Renesas Technology product distributor for the latest product information before purchasing a product listed herein. The
information described here may contain technical inaccuracies or typographical errors. Renesas Technology Corporation and Renesas Solutions Corporation
assume no responsibility for any damage, liability, or other loss rising from these inaccuracies or errors. Please also pay attention to information published
by Renesas Technology Corporation and Renesas Solutions Corporation by various means, including the Renesas home page (http://www.renesas.com).
• When using any or all of the information contained in these materials, including product data, diagrams, charts, programs, and algorithms, please be sure
to evaluate all information as a total system before making a final decision on the applicability of the information and products. Renesas Technology
Corporation and Renesas Solutions Corporation assume no responsibility for any damage, liability or other loss resulting from the information contained
herein.
• Renesas Technology semiconductors are not designed or manufactured for use in a device or system that is used under circumstances in which human life
is potentially at stake. Please contact Renesas Technology Corporation, Renesas Solutions Corporation or an authorized Renesas Technology product
distributor when considering the use of a product contained herein for any specific purposes, such as apparatus or systems for transportation, vehicular,
medical, aerospace, nuclear, or undersea repeater use.
• The prior written approval of Renesas Technology Corporation and Renesas Solutions Corporation is necessary to reprint or reproduce in whole or in part
these materials.
• If these products or technologies are subject to the Japanese export control restrictions, they must be exported under a license from the Japanese government
and cannot be imported into a country other than the approved destination. Any diversion or reexport contrary to the export control laws and regulations of
Japan and/or the country of destination is prohibited.
• Please contact Renesas Technology Corporation or Renesas Solutions Corporation for further details on these materials or the products contained therein.
Precautions to be taken when using this product
• This product is a development supporting unit for use in your program development and evaluation stages. In mass-producing your program you have finished
developing, be sure to make a judgment on your own risk that it can be put to practical use by performing integration test, evaluation, or some experiment
else.
• In no event shall Renesas Solutions Corporation be liable for any consequence arising from the use of this product.
• Renesas Solutions Corporation strives to cope with the issues given below at some charge or without charge.
(1) Repairing or replacing a flawed product. There can be instances in which a product cannot be repaired if more than one year have passed since the
discontinuance of its marketing.
(2) Renovating or providing a workaround for product malfunction. This does not necessarily mean that Renesas Solutions Corporation guarantees the
renovation or the provision under any circumstances.
• This product has been developed by assuming its use for program development and evaluation in laboratories. Therefore, it does not fall under the application
of Electrical Appliance and Material Safety Law and protection against electromagnetic interference when used in Japan.
• This product is not qualified under UL or other safety standards and IEC or other industry standards. This fact must be taken into account when taking this
product from Japan to some other country.
Safety Symbol and Meaning
If the requirements shown in the "CAUTION" sentences are ignored,
CAUTION
the equipment may cause personal injury or damage to the products.
Rev. 1.0
April 1, 2003
( 1 / 7 )
REJ10J0005-0100 Z
Download from Www.Somanuals.com. All Manuals Search And Download.
5. Connection Procedure
Connection to the M32100T2-SDI-E
The procedure for connecting the M32182T2-PTC is shown
according to applications. See Figures 2 to 4.
5.1 For the M32100T2-SDI-E
(1) Mount the NQPACK144SD.
(2) Mount the YQPACK144SD on the NQPACK144SD.
(3) Secure the four corners of the YQPACK144SD with the
YQ-GUIDE's.
(4) Set the clock select switch.
(5) Mount the M32182T2-PTC on the YQPACK144SD.
(6) Connect the emulator probe to the M32182T2-PTC.
: Position of No. 1 pin
Be sure to match the position of No. 1 pin of the foot pattern
and each part.
Figure 2 Connection to the M32100T2-SDI-E
( 3 / 7 )
Download from Www.Somanuals.com. All Manuals Search And Download.
5.2 For the M32100T-SDI-E and M32170T-SDI
(1) Mount the NQPACK144SD.
Connection to the M32100T-SDI-E or M32170T-SDI
(2) Mount the YQPACK144SD on the NQPACK144SD.
(3) Secure the four corners of the YQPACK144SD with the
YQ-GUIDE's.
(4) Set the clock select switch.
(5) Mount the M32182T2-PTC on the YQPACK144SD.
(6) Mount the M3T-PTC-CNV on the M32182T2-PTC.
(7) Connect the probe of the emulation pod and the
M32182T2-PTC via the SDI MCU control interface
cable and the SDI trace interface cable.
: Position of No. 1 pin
Be sure to match the position of No. 1 pin of the foot pattern
and each part.
Figure 3 Connection to the M32100T-SDI-E or M32170T-SDI
( 4 / 7 )
Download from Www.Somanuals.com. All Manuals Search And Download.
5.3 For Board-mounted Evaluation
Connection for board-mounted evaluation
(1) Mount the NQPACK144SD.
(2) Mount the M32182F3xFP on the NQPACK144SD.
(3) Mount the HQPACK144SD on the NQPACK144SD.
: Position of No. 1 pin
Be sure to match the position of No. 1 pin of the foot pattern
and each part.
Figure 4 Connection for board-mounted evaluation
6. Selecting a Clock
Mount an oscillator to X2 as
shown in the diagram printed on
the board.
With the M32182T2-PTC, it is possible to select a clock
supply to the MCU by the clock select switch (SW1). Select
a clock supply as shown below.
However, when used with the M32182T2-PTC, the clock
cannot be supplied from the target system.
Connected to XIN pin of MCU
ConnectedtoXOUTpinofMCU
10 MHz: Suppliestheclock(X1:10MHz)ontheM32182T2-
PTC board to the MCU.
R9: 1M Ω
R7: 510 Ω
C20: 27 pF
C22: 27 pF
SOCKET: Supplies the clock to the MCU from the socket
(X2) for mounting the oscillator on the
M32182T2-PTC board. By mounting the oscilla-
tor to the X2 socket of the MCU, it is possible to
change the operating frequency.
Figure 5 Connection diagram of X2 socket
For more details on the connecting the X2 socket
and the MCU, see Figure 5 (right).
( 5 / 7 )
Download from Www.Somanuals.com. All Manuals Search And Download.
7. External Dimensions and a Sample Foot Pattern of the M32182T2-PTC
Unit: mm
Figure 6 External dimensions and a sample foot pattern of the M32182T2-PTC
( 6 / 7 )
Download from Www.Somanuals.com. All Manuals Search And Download.
8. Precautions
CAUTION
Cautions to Be Taken for Emulator:
• For debugging, use this product in the combination with the M32170T-SDI,
M32100T-SDI-E or M32100T2-SDI-E emulator.
• When using with the M32170T-SDI or M32100T-SDI-E, the following restriction
is applied according to the MCU operating frequency.
- More than 66 MHz:
Compared with the M32100T2-SDI-E, more loss of trace information occurs.
- 66 MHz or less:
Same as the M32100T2-SDI-E.
• When using with the M32170T-SDI or M32100T-SDI-E, connect the both cables
for connecting the emulator, the SDI MCU control interface cable (10-pin) and the
SDI trace interface cable (20-pin).
• For the precautions for the combination of the emulator, refer to the user's manual
of each emulator.
Cautions for Differences between MCUs and This Product:
• For debugging, as the M32180F8VWG (1MB internal Flash ROM) on the M32182T2-
PTC is used, be careful about the difference of the internal Flash ROM size when
using the M32182F3xFP.
• When the clock select switch is set to the "SOCKET" side, the oscillation occurs by
itself, be careful about the difference of the resistance and the capacitor.
• The capacitive load of the all lines of the MCU will increase depending on wirings
and connectors. Use the part whose timing is critical after checking it works
properly.
Cautions to Be Taken for This Product:
• When connecting the YQPACK144SD, be sure to use the included YQ-GUIDE's.
• We cannot accept any request for repair.
• For purchasing the NQPACK144SD, YQPACK144SD and HQPACK144SD, contact
the following:
Daimaru Kogyo Ltd.
Tokyo Eletech Corporation
• For inquiries about the product or the contents of this manual, contact your local
distributor.
( 7 / 7 )
Download from Www.Somanuals.com. All Manuals Search And Download.
|