Renesas Computer Hardware 3803L User Guide
REJ10J1334-0200  
Renesas Starter Kit for 3803L  
Tutorial Manual (for M3T-SRA74)  
RENESAS SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER  
740 FAMILY  
Rev.2.00  
Revision date: Aug.10,2007  
Renesas Solutions Corp.  
www.renesas.com  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Chapter 1. Preface  
Cautions  
This document may be, wholly or partially, subject to change without notice.  
All rights reserved. Duplication of this document, either in whole or part is prohibited without the written permission of Renesas  
Solutions Corporation.  
Trademarks  
All brand or product names used in this manual are trademarks or registered trademarks of their respective companies or  
organisations.  
Copyright  
© Renesas Solutions Corporation. 2007. All rights reserved.  
© Renesas Technology Europe Ltd. 2007. All rights reserved.  
© Renesas Technology Corporation. 2007. All rights reserved.  
Renesas Global Website:  
Renesas Europe Website:  
http://www.renesas.com/  
http://eu.renesas.com/  
Glossary  
ASM  
Assembler  
MCU  
PC  
Microcontroller  
CPU  
E8a  
Central Processing Unit  
E8a On-chip debugger module  
Liquid Crystal Display  
Program Counter  
Printed Circuit Board  
Renesas Starter Kit  
PCB  
RSK  
LCD  
LED  
Light Emitting Diode  
1
Download from Www.Somanuals.com. All Manuals Search And Download.  
 
Chapter 2. Introduction  
This manual is designed to answer, in tutorial form, the most common questions asked about using the Renesas Starter Kit: The tutorials  
help explain the following:  
•
•
•
How do I compile, link, download, and run a simple program on the Renesas Starter Kit?  
How do I build an embedded application?  
How do I use Renesas’s development tools?  
The project generator will create a tutorial project with two selectable build configurations:  
•
•
‘Debug’ is a project built with the debugger support included.  
‘Release’ build demonstrating code suitable for release in a product.  
Files referred to in this manual are installed using the project generator as you work through the tutorials. The tutorial examples in this  
manual assume that installation procedures described in the Renesas Starter Kit Quick Start Guide have been completed.  
Please refer to the Quick Start Guide for details of installation and configuration of the Renesas Starter Kit.  
NOTE: These tutorials are designed to show you how to use the Renesas Starter Kit and are not intended as a comprehensive  
introduction to the High-performance Embedded Workshop debugger, the compiler tool-chains or the E8a Emulator – please  
consult the relevant user manuals for more in-depth information.  
2
Download from Www.Somanuals.com. All Manuals Search And Download.  
 
Chapter 3. Tutorial Project Workspace  
The workspace includes all of the files for two build configurations. The tutorial code is common to both the Debug and the Release build  
configurations. The tutorial is designed to show how code can be written, debugged then downloaded in a ‘Debug’ situation.  
The build configuration menu in High-performance Embedded Workshop allows the project to be configured such that certain files may  
be excluded from each of the build configurations. This allows the inclusion of the debug monitor within the Debug build, and its  
exclusion in the Release build. Contents of common ASM files are controlled with defines set up in the build configuration options and  
#ifdefstatements within the same files.  
Maintaining only one set of project files means that projects are more controllable.  
3
Download from Www.Somanuals.com. All Manuals Search And Download.  
 
Chapter 4. Project Workspace  
4.1. Introduction  
High-performance Embedded Workshop is an integrated development tool that allows the user to write, compile, program and debug a  
software project on any of the Renesas Microcontrollers. High-performance Embedded Workshop will have been installed during the  
installation of the software support for the Renesas Starter Kit product. This manual will describe the stages required to create and debug  
the supplied tutorial code.  
4.2. Creating a new Project Workspace  
Start High-performance Embedded Workshop from the Windows Start Menu, Start ¦ All Programs ¦ Renesas ¦ High-Performance  
Embedded Workshop  
Open a new tutorial workspace from the [File -> New Workspace…] menu or select ‘Create a new project workspace’ when presented with  
the ‘Welcome!’ dialog.  
The example above shows the New Project Workspace dialog with the RSKM3803 selected.  
•
•
•
•
Select the 740 CPU Family and “Renesas 740 Family Standard” Toolchain.  
Select the “RSKM3803” Project type from the left-hand Projects list.  
Enter a Workspace Name; all your files will be stored within a folder called c:\WorkSpace\<your_name>  
The project name field will be pre-filled to match the workspace name above; you can change this name if you wish.  
Note: High-performance Embedded Workshop allows you to add multiple projects to a workspace. You may add the  
sample code projects later so you may wish to choose a suitable name for the Tutorial project now.  
•
Click <OK> to start the Renesas Starter Kit Project Generator wizard.  
4
Download from Www.Somanuals.com. All Manuals Search And Download.  
 
The next dialog presents the three types of example project available:  
1. Tutorial: This is the one of interest at this time; the code is explained later in this manual.  
2. Sample code: this provides examples for using various peripherals. If you select this and click <Next> it will open a new dialog  
allowing the selection of many code examples for the peripheral modules of the device.  
3. Application: where the debugger is configured but there is no program code. This project is suitable for the user to add code  
without having to configure the debugger.  
•
•
Select “Tutorial” as the type of project to generate and then click <Next>.  
Click <Finish> to create the project  
The project generator wizard will display a confirmation dialog. Press <OK> to create the project and insert the necessary files.  
A tree showing all the files in this project will appear in High-performance Embedded Workshop.  
•
To view the file ‘main.a74’, double click on the file in the Workspace window, ‘main.a74’ will appear in the code window.  
4.3. Build Configurations and Debug Sessions  
The workspace that has been created contains two build configurations and two debug sessions. The Build Configuration allows the same  
project to be built but with different compiler options. The options available to the user are fully described in the High-performance  
Embedded Workshop User’s Manual.  
4.3.1. Build Configuration  
The build configurations are selected from the left hand drop down list on the toolbar. The options available are Debug and Release. The  
debug build is configured for use with the debugger. The Release build is configured for final ROM-able code.  
A common difference between the two builds may be the optimisation settings. With Optimisation turned on the Debugger may seem to  
execute code in an unexpected order. To assist in debugging it is often helpful to turn optimisation off on the code being debugged.  
•
Select the ‘Debug Build’ Configuration.  
4.3.2. Debug Session  
The debug sessions are selected from the right hand drop down list on the toolbar. The options vary between Renesas Starter Kit types  
however one will always start Debug and include the type of debug interface, the alternate selection is the ‘DefaultSession’. The purpose of  
the debug sessions is to allow the use of different debugger tools or different debugger settings on the same project.  
•
Select the ‘Session740_E8a_SYSTEM’ debug  
session.  
5
Download from Www.Somanuals.com. All Manuals Search And Download.  
 
Chapter 5. Building the Tutorial Project  
The tutorial project build settings have been pre-configured in the tool-chain options. To view the tool chain options select the ‘Build’ menu  
item and the relevant tool-chain. This should be the first option on the drop down menu.  
The dialog that is displayed will be specific to the tool-chain selected.  
The Configuration pane on the left hand side will exist on all the  
tool-chain options. It is important when changing any setting to  
be aware of the current configuration that is being modified. If  
you wish to modify multiple or all build configurations this is  
possible by selecting ‘All’ or ‘Multiple’ from the ‘Configuration’  
drop down list.  
•
Review the options on each of the tabs and  
‘Category’ drop down lists to be aware of the  
options available.  
Note: For the purposes of the tutorial, leave all  
options at default.  
When complete close the dialog box by clicking <OK>.  
5.1. Building Code  
There is a choice of three shortcuts available for building the project.  
1. Selecting the ‘Build All’ tool bar button.  
This will build everything in the project that has not been excluded from the build. This includes the standard library.  
2. Selecting the ‘Build’ tool bar button.  
This will build all files that have changed since the last build. The standard library will not be built unless an option has been  
changed.  
3. Pressing <F7>  
This is equivalent to pressing the ‘Build’ button described above.  
•
Build the project now by pressing <F7> or pressing one of the build icons as shown above.  
During the build each stage will be reported in the Output Window.  
The build will complete with an indication of any errors and warnings encountered during the build.  
6
Download from Www.Somanuals.com. All Manuals Search And Download.  
 
5.2. Connecting the debugger  
For this tutorial it is not necessary to provide an external power supply to the board. The power will be obtained from the USB port. Please  
be aware that if you have too many devices connected to your USB port it may be shut down by Windows. If this happens remove some  
devices and try again. Alternatively provide an external power source taking care to ensure the correct polarity and voltage.  
The Quick Start Guide provided with the Renesas Starter Kit board gives detailed instructions on how to connect the E8a to the host  
computer. The following assumes that the steps in the Quick Start Guide have been followed and the E8a drivers have been installed.  
•
Fit the LCD module to J8 on the Renesas Starter Kit ensuring that pin 1 on the module corresponds to the indication on the  
Renesas Starter Kit PCB.  
•
•
Connect the E8a debugger to the USB port on your computer.  
Connect the E8a Debugger to the target hardware ensuring that it is plugged into the connector marked J6 which is nearest  
the power connector.  
•
If supplying external power to the board this can be turned on now.  
5.3. Connecting to the target with the E8a  
This section will take you through the process of connecting to the device, programming the Flash and executing the code.  
•
•
Select the ‘Session740_E8a_SYSTEM’ debug  
session.  
Click the <Connect> button  
on the debug toolbar.  
•
The “Emulator Setting” dialog will be shown.  
Select the correct MCU group and device type  
(3803L Group and M38039FFL for RSKM3803L  
as illustrated)  
•
•
Select ‘Erase Flash and Connect’.  
If the E8a is to provide power to the CPU  
board, select ‘Power from Emulator’ and  
choose the ‘5.0V’ option.  
Otherwise connect a 5V centre positive supply.  
Press <OK>  
•
7
Download from Www.Somanuals.com. All Manuals Search And Download.  
 
•
•
The Flash Memory write program will be  
downloaded to the target.  
The Output window in High-performance  
Embedded Workshop will show ‘Connected’.  
Note: The connection to the target will activate  
the debugger buttons on the High-performance  
Embedded Workshop toolbar.  
Now is a good time to save the High-performance Embedded Workshop session.  
Select ‘File’ | ‘Save Session’.  
If you have changed any workspace settings now is a good time to save the workspace.  
Select ‘File’ | ‘Save Workspace’.  
•
•
8
Download from Www.Somanuals.com. All Manuals Search And Download.  
Chapter 6. Downloading and Running the Tutorial  
Once the code has been built in High-performance Embedded Workshop it needs to be downloaded to the Renesas Starter Kit itself.  
There will now be an additional category in the workspace view for ‘Download Modules’  
•
Right click on the download module listed and  
select ‘Download’.  
Note: The output display will show “Flash memory  
write end” to confirm the completion of the  
download.  
On completion of the download the debugger is ready for the code to be executed.  
To start debugging it is necessary to reset the debugger and target.  
•
Press ‘Reset CPU’ on the debug toolbar.  
The File window should open the Tutorial code at the entry point. An arrow marks the current position of the program counter.  
We will now skip over the initialisation code and proceed to the main tutorial.  
9
Download from Www.Somanuals.com. All Manuals Search And Download.  
 
•
Place a breakpoint at the call to InitialiseDisplaysubroutine.  
Breakpoints can only be set when the E8a is connected to the target and the module is downloaded. Breakpoints can be  
set by double-clicking in the grey column containing the PC arrow next to the line to break at; or selecting the line and  
pressing F9; or right click on the line and select ‘Toggle breakpoint’. Alternatively set an eventpoint, by double-clicking in  
the column to the left of the breakpoint column. Up to 2 eventpoints can be set. Eventpoints do not require programming the  
flash memory and so are faster to use.  
•
Press ‘Reset Go’ on the debug toolbar.  
The code will execute to the breakpoint. At this point all the device initialisation will have been completed.  
The code window will show the new position of the program counter.  
•
•
Insert a breakpoint on the call to the TimerADCsubroutine.  
Right click on the call to FlashLEDssubroutine  
and select ‘Go To Cursor’ as illustrated.  
10  
Download from Www.Somanuals.com. All Manuals Search And Download.  
The code will execute to the selected line and stop. An automatic breakpoint was inserted in the code and then removed after calling the  
break.  
•
Press ‘Step Over’ on the debug toolbar.  
The code will run and flash the LEDs 200 times. The debugger will not exit until all 200 flashes have completed or a button is pressed on the  
Renesas Starter Kit.  
•
To stop the LEDs flashing press the SW1 button on the Renesas Starter Kit to exit the FlashLEDssubroutine.  
The code will run to the breakpoint we previously set on the TimerADC subroutine, note that the yellow PC arrow will now be  
superimposed on the breakpoint indicator, this confirms the breakpoint has been reached.  
The TimerADCsubroutine initialises an interrupt on an available internal timer. On a compare match in the timer module, an interrupt is  
generated. In the TimerADCcode version the interrupt reads the last ADC conversion from the external potentiometer and uses the  
result to set the next compare match value. The ADC conversion is then re-started.  
The interrupt initialisation is completed as part of the hardware setup. This is contained in the file ‘interrupts.a74’.  
•
•
•
•
Open the file ‘interrupts.a74’ by double clicking on the file in the Workspace window.  
Review this file and find the interrupt function that changes the LED pins; TimerX_Handler().  
Set a breakpoint on the line where the LED pins are modified (ToggleLEDssubroutine).  
Press <Go> or <F5> to run the code from the  
current PC position.  
The code will stop in the interrupt routine. It is now possible to step through the interrupt function.  
•
•
Remove the breakpoint in the interrupt by double clicking again before exiting the function.  
Press <Go>to run the code from the current PC  
position.  
The code will now run to the infinite loop at the end of Main. The user LEDs will now be flashing. You can modify the flashing rate by  
adjusting the potentiometer on the Renesas Starter Kit.  
•
Press <Stop> on the debug toolbar.  
11  
Download from Www.Somanuals.com. All Manuals Search And Download.  
•
Press ‘CTRL-B’ to open the breakpoint window.  
This dialog is not available if user debugged using  
eventpoints as suggested at top of page 10. ‘CTRL-E’  
will open the eventpoint window. Eventpoints can be  
viewed in Breakcondition tab of event window.  
•
•
Press <Remove All>.  
Press <OK>.  
•
•
Open the file ‘main.a74’  
Insert a breakpoint on Statics_Testsubroutine.  
The Statics_Test is used to demonstrate that the initialisation has successfully copied all initialised variables from storage in flash to RAM.  
Press <Reset Go> on the debug toolbar.  
•
The code will stop at the breakpoint. (Press one of the Renesas Starter Kit buttons to bypass the flashing LED test.)  
Press <Step In> on the debug toolbar.  
•
It is possible to monitor variables during debugging of the code. To set up a ‘watch’ on a variable place the mouse over the variable. If the  
variable is available in the current context a tooltip will be displayed with the current value of the variable.  
•
Hover the mouse over the ‘STR_DISP’ variable and its value will appear as a tooltip. Now right click on the variable name  
and select ‘Instant Watch’.  
A dialog will open showing the variable and allowing further details to be explored.  
Press <Add>  
•
12  
Download from Www.Somanuals.com. All Manuals Search And Download.  
The dialog will close and a new pane will open in the workspace containing the variable.  
•
Press <Go To Memory>  
In the ASCII column on a Memory Window, it is possible to see that the string has been successfully initialised to ‘ STATIC ‘.  
•
•
Set a breakpoint on the call to DisplayStringsubroutine inside the for loop.  
Press ‘Go’ to run the code from the current PC position.  
•
Press ‘Step Over’ on the debug toolbar.  
When the program stops you can see the modified string displayed on the second line of the LCD.  
Inspection of the watch pane and Memory Window will show that the first character of the variable string has been replaced with the first  
character of the constant replacement string.  
•
•
Remove the breakpoint  
Right click on the ‘DisplayString;’ subroutine call after the loop and select ‘Go To Cursor’.  
This shows that the variable was initialised at program start up and can be overwritten with ‘TESTTEST’.  
You have now run the tutorial code and used many of the common features of the debugger. We suggest that you review the rest of the  
tutorial code as many functions have important information on the operation of the code, the assembler directives and comments on when  
they should or must be used. Please refer to Chapter 7 for more information on the project files.  
13  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Chapter 7. Project Files  
7.1. Standard Project Files  
Each of the tutorial files has detailed comment text describing the function of each code entry. Please refer to the source code for greater  
detail on the purpose and operation of the assembler specific details.  
7.1.1. Main tutorial code (main.a74 / main.inc)  
This is the entry point of the main tutorial code.  
The call to InitRAM(Do-While Zero Setting), ConfigurePortPins, EnablePeripheraModules and  
ConfigureInterruptswill initialise the device hardware and peripherals ready for the tutorial software. The display initialisation  
and string display functions operate on the LCD display module. Check compatibility with ks0066u controller and pin connection on the  
schematic before connecting an LCD module not supplied by Renesas.  
14  
Download from Www.Somanuals.com. All Manuals Search And Download.  
   
7.1.2. Board initialisation code (hwsetup.a74)  
There are two stages to the configuration of the microcontroller device. The code to demonstrate this is therefore split into two functions.  
Each function is written specifically for the device supported. The function calls are shown below.  
15  
Download from Www.Somanuals.com. All Manuals Search And Download.  
 
Chapter 8. Additional Information  
For details on how to use High-performance Embedded Workshop, refer to the High-performance Embedded Workshop manual available  
on the CD or from the web site.  
Further information available for this product can be found on the Renesas website at:  
http://www.renesas.com/renesas_starter_kits  
General information on Renesas Microcontrollers can be found at the following websites.  
Global:  
http://www.renesas.com/  
Regional (English language) sites can be accessed from the Global site, or directly by going to:  
Europe:  
Americas:  
Asia:  
http://eu.renesas.com  
http://america.renesas.com  
http://sg.renesas.com  
16  
Download from Www.Somanuals.com. All Manuals Search And Download.  
 
Renesas Starter Kit for 3803L  
Tutorial Manual (for M3T-SRA74)  
Publication Date Rev.2.00 Aug.10,2007  
Published by:  
Renesas Solutions Corp.  
4-1-6, Miyahara, Yodogawa-ku, Osaka City, 532-0003, Japan  
©2007 Renesas Solutions Corp., Renesas Technology Europe Ltd. and Renesas Technology Corp.,  
All Rights Reserved.  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Renesas Starter Kit for 3803L  
Tutorial Manual (for M3T-SRA74)  
Renesas Solutions Corp.  
4-1-6, Miyahara, Yodogawa-ku, Osaka City, 532-0003, Japan  
Download from Www.Somanuals.com. All Manuals Search And Download.  

RCA Speaker System RS2046 User Guide
RedMax Chainsaw GZ400 User Guide
Remington Power Tools Lawn Mower MPS6017A User Guide
Renesas Computer Hardware FP 80Q User Guide
Rotel Turntable RP900 User Guide
Samsung Car Video System 700DX 2 User Guide
Samsung Home Theater Server MR 00EA1 User Guide
Samsung VCR DVD V80 User Guide
Sears Patio Furniture D71M80903 User Guide
Sears Snow Blower 5369183 User Guide