28879_R800_revised series 11/4/05 4:02 PM Page 1
®
®
MC
Use and
Care Guide
R-830
R-835
Download from Www.Somanuals.com. All Manuals Search And Download.
28879_R800_revised series 11/4/05 4:02 PM Page 4
Product Features
(A) Head & cutter assembly
(B) ON/OFF button
Shaver Parts
(C) Power port
(D) Trimmer button
(E) Head guard
(F) Cleaning brush
(E)
(G)
(A)
(G) Storage pouch (Model R-835)
(F)
(B)
Easy-View® Trimmer
(C)
(D)
4
5
Download from Www.Somanuals.com. All Manuals Search And Download.
28879_R800_revised series 11/4/05 4:02 PM Page 6
How to Use
Usage Tips
®
Please refer to your Safety Instructions
before operating your shaver.
Avoid holding the shaver at an angle so
only one head touches the skin. This
could cause skin irritation.
■ Use short, circular
strokes. Use your free
hand to stretch your skin.
This encourages your
whiskers to stand out,
making it easier for them
to enter the cutting chamber.
■ It is not necessary to apply pressure
while shaving, just let the shaver glide
lightly on your skin. Never press hard.
Pressing only flattens your whiskers,
which makes it harder for them to enter
the cutting chamber. It will also wear out
the cutting surface more quickly. A gentle
touch makes shaving easier and helps
avoid possible skin irritation.
Operating the Easy-View
Getting a close,
Trimmer
comfortable shave
The Easy-View®pop-up trimmer extends to
trim mustache, sideburns, etc.
Remington shavers need no adjustments to
their heads or cutters before you shave. The
heads will automatically adjust to the con-
tours of your face.
Removing the Headguard
Before operating your shaver, remove the
headguard, which protects the screen and
cutter assembly. It is important to remove
the headguard correctly to avoid damaging
the clips that hold it to the shaver.
1. Press lightly on the top of the headguard.
2. Lift the lower rear edge.
■ Trimmer is turned off until it is extended
for use.
■ Push the trimmer
button up to pop up
the trimmer.
Adjusting to your new shaver
As with every shaver, your shave will
improve over time. So allow about three
weeks to develop an effective shaving style
and for your beard to adjust to the new
shaver. The adaptation period may take a
little longer if your skin is sensitive, or if
you alternate between shaving methods.
■ Hold the shaver
with the trimmer
toward you when
trimming.
3. Pull the headguard away from the
shaver.
! Always keep the protective head guard on
the shaver head and keep the trimmer in the
OFF position when the shaver is not in use.
■ After trimming, pull the trimmer button
downward into the OFF position. Leave it
in the down position when not in use.
Before you begin:
■ Wait at least 15 minutes
after getting up before
ON/OFF Switch
12
To activate the shaver, press in the locking
bar while pushing the power button up.
9
3
shaving to ensure the
face is free of puffiness
that may be present from
sleeping.
■ Make sure your face
is clean and dry before
starting.
■ Always use a clean, dry
shaver.
■ Make sure the cutter head
6
To Trim
Trim mustache
Power System
■ Corded shavers can only be used while
they are plugged into an electrical outlet.
■ Use the shaver heads to trim the lower
edge of your mustache. Hold shaver at
desired trim line for a quick, easy,
professional trim.
■ Use the pop-up trimmer
for the upper edge of your
mustache. Extend the
trimmer and touch the
edge of it to the desired
line.
Corded Operation of the
R-830 and R-835
■ Slide the power button down to the OFF
position.
assembly is in the locked position.
■ Connect the supplied AC power cord to
the shaver’s power port and then to an
electrical outlet.
To Shave
■ Push the ON/OFF button to
activate the shaver for
shaving.
Trim sideburns
■ Hold the shaver so all the
heads touch your face
together. This allows the
shaver to work the way
it was designed for the
closest shave and minimum
wear.
Extend the trimmer and touch
the edge of it to the desired
trim line.
6
7
Download from Www.Somanuals.com. All Manuals Search And Download.
28879_R800_revised series 11/4/05 4:02 PM Page 8
Cleaning and Maintenance
To assure smooth, efficient performance, it
is important to clean your shaver.
! Important: Make sure to align the two
locating holes in the Cutter Retainer
assembly with the pins in the Head Frame
Assembly. (See illustration below). Then
tighten center screw knob to lock the
cutters into place.
Cleaning Cautions
When is it Time to Replace
Your Heads and Cutters?
It is very important to replace your
heads and cutters when necessary to
ensure a close, comfortable shave with-
out irritation. We recommend they be
replaced every 12 months. Here are
some signs of head and cutter wear,
indicating that replacement is needed.
■ The construction of this shaver is for
dry operation only. It is not water-
proof. Never put the shaver in part or
completely into water.
Daily
Brush inside the
head assembly after
each use:
■ Never clean the shaver or replace the
cutters while it is plugged into an
electrical outlet.
■ Do not use an aggressive cleansing
agent as this may destroy the shaver
coatings.
■ Do not clean or remove the head assem-
bly while the shaver is running or plugged
in, as it may cause damage to the unit's
heads or cutters.
Replace head assembly on the shaver
simply by pushing it onto the shaver.
1. Turn the shaver off.
2. Grip the head
assembly by the
three ridges and
pull it off the
Cover shaver head with plastic headguard
between uses. When removing the head-
guard or placing it back onto the shaver,
do not apply pressure to floating cutter
surfaces, as you may damage them.
Irritation
As the heads get excessively worn you may
experience some skin irritation. This would
be especially noticeable when you apply
after-shave lotion.
shaver.
3. Use the cleaning
brush to sweep
out the internal
part of the head
assembly and the
hair pocket area,
where 3 shaver
spindles are located.
4. Replace head
assembly.
■ Replace worn or damaged parts with
Pulling
Remington® replacement parts only.
When the cutters wear you may feel a
sense of pulling and a loss of closeness
when you shave. This is an indication that it
is time to replace your heads and cutters.
Cutter retainer
assembly
Center
screw
knob
The replacement parts for your shaver is
model SP-16.
Locating holes
Weekly
U.S. residents: To order, contact
us at 800-736-4648, visit us at
your local retailer.
Clean under the cutter assembly at least
once a week:
Head/frame
assembly
1. Turn the shaver off.
2. Open the head assembly as above.
3. Unscrew the center screw knob to
remove the cutter retainer assembly.
4. Use the cleaning brush to sweep the dust
and hairs from under the cutters.
5. Replace head assembly.
Canadian residents: For any shaver
accessory requirements, please call
800-268-0425 or visit us at
Floating
cutter
Locating pins
heads
Lubricate
Remington® Shaver Saver® Lubricant (SP-4)
lubricates and cleans your shaver's cutters
and head assembly. The lubricant helps
remove hair clippings while reducing wear.
A quick spray after each shave keeps your
shaver operating at peak performance.
8
9
Download from Www.Somanuals.com. All Manuals Search And Download.
28879_R800_revised series 11/4/05 4:02 PM Page 10
Performance Guarantee
This warranty does not cover products
damaged by the following:
This warranty gives you specific legal rights
and you may also have other rights which
vary from state to state or province to
province. Some states do not allow the
exclusion or limitation of incidental, special
or consequential damages.
120 VAC, 60 Hz
Full Two-Year Warranty
Spectrum Brands, Inc. warrants this product
against any defects that are due to faulty
material or workmanship for a two-year
period from the original date of consumer
purchase. This warranty does not include
damage to the product resulting from
accident or misuse.
■
Accident, misuse, abuse or alteration
of the product
U.S. Patents: D486,942: 5,390,416;
5,408,749
Canadian Patents: D100892: 2,091,039;
2,114,923; 2,111,626
■
■
■
Servicing by unauthorized persons
Use with unauthorized accessories
REMINGTON & MICROFLEX are trademarks
of ROVCAL, INC.
Connecting it to incorrect current
and voltage
Performace Guarantee
Spectrum Brands, Inc. Money-back Offer
If within 30 days after you have purchased
your Remington® branded product, you are
not satisfied and would like a refund, return
it with the sales slip indicating purchase
price and date of purchase to the retailer
from whom it was purchased. Spectrum
Brands, Inc. will reimburse all retailers who
accept the product within 30 days from the
date of purchase. If you have any questions
concerning the money-back guarantee,
please call 800-736-4648.
If the product should become defective
within the warranty period, we will repair it
or elect to replace it free of charge. Return
your product and sales receipt with your
name, address and day time phone number
to: Spectrum Brands, Inc. , Attention:
Consumer Services, 601 Rayovac Drive,
Madison, WI 53711. For more information
call 800-736-4648.
■
■
Wrapping cord around appliance
causing premature wear & breakage
Questions or comments:
Call 800-736-4648 in U.S. or
800-268-0425 in Canada.
Any other conditions beyond our control
Or visit www.remington-products.com
SPECTRUM BRANDS, INC. SHALL NOT BE
RESPONSIBLE FOR ANY INCIDENTAL,
SPECIAL OR CONSEQUENTIAL DAMAGES
RESULTING FROM THE USE OF THIS
PRODUCT. ALL IMPLIED WARRANTIES
INCLUDING BUT NOT LIMITED TO IMPLIED
WARRANTIES OF FITNESS AND
MERCHANTABILITY, ARE LIMITED IN
DURATION TO TWO YEARS FROM DATE
OF ORIGINAL PURCHASE.
Dist. by: Spectrum Brands, Inc.,
Madison, WI 53711
Dist. by: Rayovac Canada Inc.,
Mississauga, ON L4W 2T7
Warranty excludes:
■ Screens and cutters
© 2005 ROVCAL, INC.
09/05 Job #CS28879
P/N15486
KEEP ORIGINAL SALES RECEIPT AS
PROOF OF PURCHASE FOR WARRANTY
PURPOSES.
MADE IN CHINA
®
10
11
Download from Www.Somanuals.com. All Manuals Search And Download.
28879_R800_revised series 11/4/05 4:02 PM Page 36
®
Download from Www.Somanuals.com. All Manuals Search And Download.
|