Model No. RCTL07809.0
Serial No.
USER'S MANUAL
Write the serial number in the
space above for reference.
Serial Number
Decal
QUESTIONS?
If you have questions, or if parts are
damaged or missing, PLEASE
CONTACT OUR CUSTOMER SER-
VICE DEPARTMENT DIRECTLY.
CALL TOLL-FREE:
1-888-936-4266
Mon.–Fri., 7:30 until 16:30 ET
(excluding holidays)
OR E-MAIL US:
CAUTION
Read all precautions and instruc-
tions in this manual before using
this equipment. Save this manual
for future reference.
Download from Www.Somanuals.com. All Manuals Search And Download.
IMPORTANT PRECAUTIONS
WARNING:
To reduce the risk of serious injury, read all important precautions and in-
structions in this manual and all warnings on your treadmill before using your treadmill. ICON as-
sumes no responsibility for personal injury or property damage sustained by or through the use of
this product.
1. Before beginning any exercise program, con-
sult your physician. This is especially impor-
tant for persons over age 35 or persons with
pre-existing health problems.
carrying 15 or more amps. No other appliance
should be on the same circuit. Do not use an
extension cord.
12. Use only a single-outlet surge suppressor that
meets all of the specifications described on
page 14. To purchase a surge suppressor call
the telephone number on the front cover of
this manual.
2. It is the responsibility of the owner to ensure
that all users of this treadmill are adequately
informed of all warnings and precautions.
3. Use the treadmill only as described.
13. Failure to use a properly functioning surge
suppressor could result in damage to the con-
trol system of the treadmill. If the control sys-
tem is damaged, the walking belt may slow,
accelerate, or stop unexpectedly, which may
result in a fall and serious injury.
4. Place the treadmill on a level surface, with at
least 8 ft. (2.4 m) of clearance behind it and 2
ft. (0.6 m) on each side. Do not place the
treadmill on any surface that blocks air open-
ings. To protect the floor or carpet from dam-
age, place a mat under the treadmill.
14. Keep the power cord and the surge suppres-
sor away from heated surfaces.
5. Keep the treadmill indoors, away from mois-
ture and dust. Do not put the treadmill in a
garage or covered patio, or near water.
15. Never move the walking belt while the power
is turned off. Do not operate the treadmill if
the power cord or plug is damaged, or if the
treadmill is not working properly. (See TROU-
BLESHOOTING on page 22 if the treadmill is
not working properly.)
6. Do not operate the treadmill where aerosol
products are used or where oxygen is being
administered.
7. Keep children under age 12 and pets away
from the treadmill at all times.
16. Read, understand, and test the emergency
stop procedure before using the treadmill (see
HOW TO TURN ON THE POWER on page 16).
8. The treadmill should be used only by persons
weighing 300 lbs. (136 kg) or less.
17. Never start the treadmill while you are stand-
ing on the walking belt. Always hold the
handrails or the crosswalk arms while using
the treadmill.
9. Never allow more than one person on the
treadmill at a time.
10. Wear appropriate exercise clothes while
using the treadmill. Do not wear loose clothes 18. The treadmill is capable of high speeds.
that could become caught in the treadmill.
Athletic support clothes are recommended
for both men and women. Always wear ath-
letic shoes. Never use the treadmill with bare
feet, wearing only stockings, or in sandals.
Adjust the speed in small increments to avoid
sudden jumps in speed.
19. The pulse sensor is not a medical device.
Various factors, including the user's move-
ment, may affect the accuracy of heart rate
readings. The pulse sensor is intended only
as an exercise aid in determining heart rate
trends in general.
11. When connecting the power cord (see page
14), plug the power cord into a surge sup-
pressor (not included) and plug the surge
suppressor into a grounded circuit capable of
3
Download from Www.Somanuals.com. All Manuals Search And Download.
20. Never leave the treadmill unattended while it
is running. Always remove the key, unplug
the power cord, and switch the reset/off cir-
cuit breaker to the off position when the
treadmill is not in use. (See the drawing on
page 5 for the location of the circuit breaker.)
25.
DANGER:
Always unplug the power
cord immediately after use, before cleaning the
treadmill, and before performing the mainte-
nance and adjustment procedures described in
this manual. Never remove the motor hood un-
less instructed to do so by an authorized ser-
vice representative. Servicing other than the
procedures in this manual should be performed
by an authorized service representative only.
21. Do not attempt to raise, lower, or move the
treadmill until it is properly assembled. (See
ASSEMBLY on page 6, and HOW TO FOLD
AND MOVE THE TREADMILL on page 21.)
You must be able to safely lift 45 lbs. (20 kg)
to raise, lower, or move the treadmill.
26. This treadmill is intended for in-home use
only. Do not use this treadmill in a commer-
cial, rental, or institutional setting.
22. When folding or moving the treadmill, make
sure that the storage latch is holding the
frame securely in the storage position.
27. Over exercising may result in serious injury
or death. If you feel faint or if you experience
pain while exercising, stop immediately and
cool down.
23. Never insert any object into any opening on
the treadmill.
24. Inspect and properly tighten all parts of the
treadmill regularly.
SAVE THESE INSTRUCTIONS
4
Download from Www.Somanuals.com. All Manuals Search And Download.
BEFORE YOU BEGIN
®
Thank you for selecting the revolutionary REEBOK
ing this manual, please see the front cover of this man-
ual. To help us assist you, note the product model
number and serial number before contacting us. The
model number and the location of the serial number
decal are shown on the front cover of this manual.
CROSSWALK V7.90 treadmill. The CROSSWALK
V7.90 treadmill offers an impressive selection of fea-
tures designed to make your workouts at home more
enjoyable and effective. And when youʼre not exercis-
ing, the unique treadmill can be folded up, requiring
less than half the floor space of other treadmills.
Before reading further, please familiarize yourself with
the parts that are labeled in the drawing below.
For your benefit, read this manual carefully before
using the treadmill. If you have questions after read-
Crosswalk Arm
Accessory Tray
Console
Pulse Sensor
Handrail
Upright
Key/Clip
Reset/Off
Circuit Breaker
Walking Belt
Foot Rail
Power Cord
Platform Cushion
Idler Roller
Adjustment Bolts
5
Download from Www.Somanuals.com. All Manuals Search And Download.
ASSEMBLY
Assembly requires two persons. Set the treadmill in a cleared area and remove all packing materials. Do not
dispose of the packing materials until assembly is completed. Note: The underside of the treadmill walking
belt is coated with high-performance lubricant. During shipping, some lubricant may be transferred to the top of
the walking belt or the shipping carton. This is normal and does not affect treadmill performance. If there is lubri-
cant on top of the walking belt, simply wipe off the lubricant with a soft cloth and a mild, non-abrasive cleaner.
Assembly requires the included hex keys and your own Phillips screwdriver
wrench , needlenose pliers , scissors , and rubber mallet
, adjustable
.
Use the drawings below to identify the assembly hardware. The number in parentheses below each drawing is
the key number of the part, from the PART LIST near the end of this manual. The number after the parentheses
is the quantity needed for assembly. Note: If a part is not in the hardware kit, check to see if it is preattached
to one of the parts to be assembled. To avoid damaging plastic parts, do not use power tools for assem-
bly. Extra hardware may be included.
Bolt Spacer (84)–4
1/4" Star
5/16" Star
3/8" Star
Washer (10)–2
Washer (9)–6
Washer (12)–4
Base Foot
Spacer (89)–2
#8 x 3/4"
1/4" x 1 1/4" Bolt (6)–2
#8 x 1" Tek
5/16" x 3/4"
Bolt (4)–6
Screw (1)–6
Screw (2)–4
3/8" Locknut
(11)–3
3/8" x 2" Bolt (3)–3
3/8" x 1 3/4" Bolt (8)–1
3/8" x 4" Bolt (5)–4
6
Download from Www.Somanuals.com. All Manuals Search And Download.
1. Make sure that the power cord is unplugged.
1
B
A
With the help of a second person, carefully tip
the treadmill onto its left side. Partially fold the
Frame (53) so that the treadmill is more stable;
do not fully fold the Frame yet.
Hole
60
86
88
Remove and discard the two indicated bolts (A)
and the shipping bracket (B).
2
Cut the shipping tie securing the Upright Wire
(86) to the Base (60). Locate a tie in the indi-
cated hole in the Base, and use the tie to pull
the Upright Wire out of the hole.
89
88
53
2
Attach two Base Feet (88) to the Base (60) in the
locations shown with two #8 x 1" Tek Screws (2)
and two Base Foot Spacers (89). Then, attach
two Base Feet (88) with two #8 x 1" Tek Screws
(2).
88
2
89
88
2
2. Attach a Wheel (90) to the Base (60) with a 3/8"
x 2" Bolt (3) and a 3/8" Locknut (11). Do not
overtighten the Locknut; the Wheel must
turn freely.
2
60
See the inset drawing. Cut the plastic tie near
the Upright Wire (86).
3
90
11
Cut
86
7
Download from Www.Somanuals.com. All Manuals Search And Download.
3. Press a Base Cap (85) into the Base (60).
3
Identify the Right Upright (79) and the Right
Upright Spacer (83), which are marked with
“Right” stickers. Insert the Upright Wire (86)
through the Right Upright Spacer as shown.
Then, set the Right Upright Spacer on the Base
(60).
79
86
Wire Tie
86
83
85
Have a second person hold the Right Upright
(79) near the Base (60). See the inset drawing.
Tie the wire tie in the Right Upright securely
around the end of the Upright Wire (86). Then,
pull the other end of the wire tie until the Upright
Wire is routed completely through the Right
Upright.
60
79
Wire
86
Tie
4. Hold a Bolt Spacer (84) inside the lower end of
the Right Upright (79). Insert a 3/8" x 4" Bolt (5)
with a 3/8" Star Washer (12) into the Right
Upright and the Bolt Spacer. Repeat this step
with a second Bolt Spacer (84), 3/8" x 4" Bolt
(5), and 3/8" Star Washer (12).
4
5
79
12
86
Hold the Right Upright (79) against the Right
Upright Spacer (83). Be careful not to pinch
the Upright Wire (86). Tighten the 3/8" x 4"
Bolts (5) until the heads of the Bolts touch the
Right Upright; do not fully tighten the Bolts
yet.
84
84
83
60
8
Download from Www.Somanuals.com. All Manuals Search And Download.
5. With the help of a second person, carefully tip
the treadmill onto its right side. Partially fold the
Frame (53) so that the treadmill is more stable;
do not fully fold the Frame yet.
5
A
B
Remove and discard the two indicated bolts (A)
and the shipping bracket (B).
53
11
Attach a Wheel (90) to the Base (60) with a 3/8"
x 2" Bolt (3) and a 3/8" Locknut (11). Do not
overtighten the Locknut; the Wheel must
turn freely.
3
60
90
6. Press a Base Cap (85) into the Base (60).
6
77
5
Hold a Bolt Spacer (84) inside the lower end of
the Left Upright (77). Insert a 3/8" x 4" Bolt (5)
with a 3/8" Star Washer (12) into the Left
Upright and the Bolt Spacer. Repeat this step
with a second Bolt Spacer (84), 3/8" x 4" Bolt
(5), and 3/8" Star Washer (12).
12
82
84
Hold the Left Upright Spacer (82) and the Left
Upright (77) against the Base (60). Tighten the
3/8" x 4" Bolts (5) until the heads of the Bolts
touch the Left Upright; do not fully tighten the
Bolts yet.
84
85
60
With the help of a second person, tip the tread-
mill so that the Base (60) is flat on the floor.
9
Download from Www.Somanuals.com. All Manuals Search And Download.
7. Remove the Resistance Knob (110) from a re-
sistance mechanism. Make sure that the 3/8" x
4 3/4" Bolt (112) stays inside the resistance
mechanism and that the resistance mecha-
nism does not come apart. Note: See the
lower drawing to reassemble the resistance
mechanism if necessary.
7
77
79
110
Large
Holes
108
Resistance
Apply a small amount of the included grease
around the Resistance Cone (108) and the
Upright Insert (111).
Mechanism
111
112
Insert the Resistance Cone (108) into the
Upright Insert (111) in the Left Upright (77), with
the two large holes on top as shown. Then,
tighten the Resistance Knob (110) onto the 3/8"
x 4 3/4" Bolt (112). Do not fully tighten the
Resistance Knob.
Large
Holes
Attach the other resistance mechanism to
the Right Upright (79) as described above.
110
108
111
112
8. Insert the end of a Crosswalk Arm (98) into the
hole in the top of a resistance mechanism.
Make sure that the bend in the Crosswalk
Arm is positioned as shown.
8
Bend
Tighten a #8 x 3/4" Screw (1) into the resistance
mechanism and the Crosswalk Arm (98) from
the direction shown. Then, press a Small Cap
(34) into the hole for the Screw.
98
Attach the other Crosswalk Arm (98) as de-
scribed above.
Hole
1
34
Carefully lower the Crosswalk Arms (98) down
toward the Walking Belt (42).
98
Resistance
Mechanism
Resistance
Mechanism
42
1
34
10
Download from Www.Somanuals.com. All Manuals Search And Download.
9. Remove the tie from the bracket on the Right
Handrail (105).
9
Have a second person hold the Right Handrail
(105) near the Right Upright (79).
86
Hole
Tie
4
9
Insert the Upright Wire (86) into the bottom of
the Right Handrail (105) and pull it out of the
hole in the top of the Right Handrail.
105
Attach the Right Handrail (105) to the Right
Upright (79) with three 5/16" x 3/4" Bolts (4) and
three 5/16" Star Washers (9); do not fully
tighten the Bolts yet. Be careful not to pinch
the Upright Wire (86).
4
79
10. Remove the tie from the bracket on the Left
Handrail (101).
10
101
Attach the Left Handrail (101) to the Left Upright
(77) with three 5/16" x 3/4" Bolts (4) and three
5/16" Star Washers (9); do not fully tighten
the Bolts yet.
Tie
4
9
4
77
11. Have a second person hold the console assem-
bly near the Right Upright (79).
11
Console
Assembly
Connect the Upright Wire (86) to the console
wire. See the inset drawing. The connectors
should slide together easily and snap into
place. If they do not, turn one connector and try
again. IF THE CONNECTORS ARE NOT CON-
NECTED PROPERLY, THE CONSOLE MAY
BE DAMAGED WHEN YOU TURN ON THE
POWER.
Console
Wire
Then, remove the wire tie from the Upright Wire
(86). Insert the connectors and the excess wire
into the Right Handrail (105).
105
79
86
Console
Wire
Wire Tie
Set the console assembly on the Right Handrail
(105) and the Left Handrail (not shown). Be
careful not to pinch the wires.
86
11
Download from Www.Somanuals.com. All Manuals Search And Download.
12. Be careful not to pinch the wires in the Right
12
Console Assembly
Handrail (105).
Attach the console assembly to the Right
Handrail (105) with two #8 x 3/4" Screws (1), a
1/4" x 1 1/4" Bolt (6), and a 1/4" Star Washer
(10). Repeat this step on the left side of the
console assembly. Start all four Screws and
both Bolts before tightening any of them.
105
1
See steps 4, 6, and 9–10. Tighten all the bolts
used in these assembly steps.
10
6
13. If necessary, press the Left Accessory Tray (94)
and the Right Accessory Tray (99) into the con-
sole assembly.
13
94
Console
99
Assembly
12
Download from Www.Somanuals.com. All Manuals Search And Download.
14. Raise the Frame (53) to the position shown.
Have a second person hold the Frame until
this step is completed.
14
Orient the Storage Latch (50) so that the large
barrel and the Latch Knob (51) are in the posi-
tions shown.
53
11
Remove the tie from the upper end of the
3
Storage Latch (50). Attach the upper end of the
Storage Latch to the bracket on the Frame (53)
with a 3/8" x 2" Bolt (3) and a 3/8" Locknut (11).
50
51
Remove the tie from the lower end of the
Storage Latch (50). Keep the holes in the Latch
Cap (49) aligned with the holes in the Storage
Latch. Make sure to keep the Latch Cap in-
side the Storage Latch. Attach the Storage
Latch to the bracket on the Base (60) with a 3/8"
x 1 3/4" Bolt (8). Note: It may be necessary to
move the Frame (53) back and forth to align the
Storage Latch with the bracket.
Large
Barrel
60
8
49
Lower the Frame (53) (see HOW TO LOWER
THE TREADMILL FOR USE on page 21).
15. Make sure that all parts are properly tightened before you use the treadmill. If there are sheets of clear
plastic on the treadmill decals, remove the plastic. To protect the floor or carpet, place a mat under the tread-
mill. Note: Extra hardware may be included. Keep the included hex keys in a secure place; one of the hex
keys is used to adjust the walking belt (see pages 23 and 24).
13
Download from Www.Somanuals.com. All Manuals Search And Download.
OPERATION AND ADJUSTMENT
THE PRE-LUBRICATED WALKING BELT
an equipment-grounding conductor and a grounding
plug. Plug the power cord into a surge suppressor,
and plug the surge suppressor into an appropriate
outlet that is properly installed and grounded in
accordance with all local codes and ordinances.
IMPORTANT: The treadmill is not compatible with
GFCI-equipped outlets.
Your treadmill features a walking belt coated with high-
performance lubricant. IMPORTANT: Never apply sil-
icone spray or other substances to the walking
belt or the walking platform. Such substances will
deteriorate the walking belt and cause excessive
wear.
This product is for use on a nominal 120-volt circuit,
and has a grounding plug that looks like the plug illus-
trated in drawing 1 below. A temporary adapter that
looks like the adapter illustrated in drawing 2 may be
used to connect the surge suppressor to a 2-pole
receptacle as shown in drawing 2 if a properly
grounded outlet is not available.
HOW TO PLUG IN THE POWER CORD
DANGER:
Improper connection
of the equipment-grounding conductor can
result in an increased risk of electric shock.
Check with a qualified electrician or service-
man if you are in doubt as to whether the
product is properly grounded. Do not modify
the plug provided with the product—if it will
not fit the outlet, have a proper outlet
1
Grounded Outlet Box
Surge Suppressor
Grounding Pin
installed by a qualified electrician.
Your treadmill, like any other type of sophisticated
electronic equipment, can be seriously damaged by
sudden voltage changes in your homeʼs power.
Voltage surges, spikes, and noise interference can
result from weather conditions or from other appli-
ances being turned on or off. To decrease the possi-
bility of your treadmill being damaged, always use
a surge suppressor with your treadmill (see draw-
ing 1 at the right). To purchase a surge suppressor
call the telephone number on the front cover of
this manual.
Grounding Pin
Grounded Outlet
Grounding Plug
2
Grounded Outlet Box
Adapter
Surge Suppressor
Use only a single-outlet surge suppressor that is
UL 1449 listed as a transient voltage surge sup-
pressor (TVSS). The surge suppressor must have a
UL suppressed voltage rating of 400 volts or less
and a minimum surge dissipation of 450 joules.
The surge suppressor must be electrically rated for
120 volts AC and 15 amps. There must be a moni-
toring light on the surge suppressor to indicate
whether it is functioning properly. Failure to use a
properly functioning surge suppressor could result
in damage to the control system of the treadmill. If
the control system is damaged, the walking belt
may slow, accelerate, or stop unexpectedly, which
may result in a fall and serious injury.
Lug
Metal Screw
Grounding Plug
The temporary adapter should be used only until a
properly grounded outlet (drawing 1) can be installed
by a qualified electrician.
The green-colored rigid ear, lug, or the like extending
from the adapter must be connected to a permanent
ground such as a properly grounded outlet box cover.
Whenever the adapter is used it must be held in place
by a metal screw. Some 2-pole receptacle outlet box
covers are not grounded. Contact a qualified elec-
trician to determine if the outlet box cover is
grounded before using an adapter.
This product must be grounded. If it should malfunc-
tion or break down, grounding provides a path of least
resistance for electric current to reduce the risk of elec-
tric shock. This product is equipped with a cord having
14
Download from Www.Somanuals.com. All Manuals Search And Download.
CONSOLE DIAGRAM
IN
Key
Clip
FEATURES OF THE CONSOLE
designed to help you achieve specific fitness goals. For
example, train for a long-distance run with the
Marathon workout. iFit workouts automatically control
the treadmill while the voice of a personal trainer
coaches you through every step of your workout. iFit
cards are available separately. To purchase iFit
number on the front cover of this manual. iFit
cards are also available at select stores.
The treadmill console offers a selection of features
designed to make your workouts more effective. When
the manual mode of the console is selected, the speed
and incline of the treadmill can be changed with the
touch of a button. As you exercise, the console will
display continuous exercise feedback. You can even
measure your heart rate using the built-in pulse sensor.
The console features sixteen preset workouts—four
weight loss workouts, four aerobic workouts, four en-
durance workouts, and four performance workouts.
Each workout automatically controls the speed and in-
cline of the treadmill as it guides you through an effec-
tive exercise session.
Whether you select the manual mode or a workout,
you can listen to your favorite workout music or audio
books with the consoleʼs premium stereo sound system.
To turn on the power, see page 16. To use the man-
ual mode, see page 16. To use a preset workout, see
page 18. To use an iFit workout, see page 19. To
use the information mode, see page 20. To use the
stereo sound system, see page 20.
The console also features the new iFit interactive work-
out system. The iFit system enables the console to ac-
cept iFit interactive workout cards containing workouts
15
Download from Www.Somanuals.com. All Manuals Search And Download.
HOW TO TURN ON THE POWER
HOW TO USE THE MANUAL MODE
1. Insert the key into the console.
See HOW TO TURN ON THE POWER at the left.
2. Select the manual mode.
IMPORTANT: If the treadmill has been exposed to
cold temperatures, allow it to warm to room tem-
perature before turning on the power. If you do not
do this, you may damage the console displays or
other electrical components.
Plug in the power cord (see
page 14). Next, locate the
reset/off circuit breaker on the
treadmill frame near the
When the key
is inserted,
the manual
mode will be
power cord. Switch the circuit
breaker to the reset position.
selected. If
Track
Reset
you have se-
lected a work-
IMPORTANT: The console features a display demo
mode, designed to be used if the treadmill is dis-
played in a store. If the displays light as soon as
you plug in the power cord and switch the reset/off
circuit breaker to the reset position, the demo
mode is turned on. To turn off the demo mode,
hold down the Stop button for a few seconds. If the
displays remain lit, see THE INFORMATION MODE
on page 20 to turn off the demo mode.
out, press any of the workout buttons repeatedly
until a track appears in the display.
3. Start the walking belt.
To start the walking belt, press the Start button, the
Speed increase button, or one of the numbered
Quick Speed buttons.
If you press the Start button or the Speed increase
button, the walking belt will begin to move at 1
mph. As you exercise, change the speed of the
walking belt as desired by pressing the Speed in-
crease and decrease buttons. Each time you press
one of the buttons, the speed setting will change
by 0.1 mph; if you hold down the button, the speed
setting will change in increments of 0.5 mph.
Next, stand on the foot rails of the treadmill. Find the
clip attached to the key (see the drawing on page 15)
and slide the clip onto the waistband of your clothes.
Then, insert the key into the console. After a moment,
the displays will light. IMPORTANT: In an emergency
situation, the key can be pulled from the console,
causing the walking belt to slow to a stop. Test the
clip by carefully taking a few steps backward; if the
key is not pulled from the console, adjust the posi-
tion of the clip.
If you press one of the numbered Quick Speed
buttons, the walking belt will gradually change
speed until it reaches the selected speed setting.
IMPORTANT: If there are sheets of clear plastic on
the console, remove the plastic. To prevent dam-
age to the walking platform, wear clean athletic
shoes while using the treadmill. The first time you
use the treadmill, observe the alignment of the
walking belt, and center the walking belt if neces-
sary (see page 24).
To stop the walking belt, press the Stop button.
The time will begin to flash in the display. To
restart the walking belt, press the Start button, the
Speed increase button, or one of the numbered
Quick Speed buttons.
Note: The console can display speed and distance in
either miles or kilometers. To find out which unit of
measurement is selected or to change the unit of mea-
surement, see THE INFORMATION MODE on page
20. Note: For simplicity, all instructions in this section
refer to miles.
16
Download from Www.Somanuals.com. All Manuals Search And Download.
4. Change the incline of the treadmill as desired.
6. Measure your heart rate if desired.
To change the incline of the treadmill, press the
Incline increase and decrease buttons or one of
the numbered Quick Incline buttons. Each time you
press the Incline increase or decrease button, the
incline will change by 0.5%. If you press one of the
numbered Quick Incline buttons, the treadmill will
adjust to the selected incline setting. Note: After
you press the buttons, it may take a moment for
the treadmill to reach the selected incline setting.
Before using the
handgrip pulse
sensor, remove
the sheets of
clear plastic from
the metal con-
tacts. In addition,
make sure that
your hands are
clean.
Metal Contacts
5. Follow your progress with the displays.
To measure your heart rate, stand on the foot
rails and place your hands on the metal contacts—
avoid moving your hands. When your pulse is
detected, the heart symbol in the display will begin
to flash each time your heart beats, one or two
dashes will appear, and then your heart rate will be
shown. For the most accurate heart rate read-
ing, continue to hold the contacts for at least
15 seconds.
When the
manual
mode is se-
lected, the
upper dis-
play will
Track
show a track
that represents 1/4 mile (402 meters). As you walk
or run, indicators will appear in succession around
the track until the entire track appears. The track
will then disappear and the indicators will again
begin to appear in succession.
7. Turn on the fan if desired.
The fan features high, low, and auto speed set-
tings. Press the Fan button repeatedly to select a
fan speed or to turn off the fan. When the auto
mode is selected, the speed of the fan will auto-
matically increase and decrease as the speed of
the walking belt increases and decreases. Note: If
the fan is on when the walking belt is stopped, the
fan will turn off automatically after a few minutes.
The auto mode can only be selected while the
walking belt is moving.
The left side of the lower
display will show the
elapsed time, the dis-
tance that you have
walked or run, and the in-
cline level of the tread-
mill. Press the Display button to view the time or
the distance. Note: When a preset workout is se-
lected, the display will show the time remaining in
the workout instead of the elapsed time.
8. When you are finished exercising, remove the
key from the console.
The right side of the
lower display will show
Step onto the foot rails, press the Stop button, and
adjust the incline of the treadmill to the lowest
setting. The incline must be at the lowest set-
ting or you may damage the treadmill when you
fold it to the storage position. Next, remove the
key from the console and put it in a secure place.
the approximate number
of calories you have
burned, the speed of the
walking belt, and your
pace in minutes per mile. Press the Display button
to view the speed or the pace. The right side of the
display will also show your heart rate when you
use the handgrip pulse sensor.
When you are finished using the treadmill, switch
the reset/off circuit breaker to the “off” position and
unplug the power cord. IMPORTANT: If you do
not do this, the treadmillʼs electrical compo-
nents may wear prematurely.
To reset the display, press the Stop button, remove
the key, and then reinsert the key.
17
Download from Www.Somanuals.com. All Manuals Search And Download.
HOW TO USE A PRESET WORKOUT
1. Insert the key into the console.
resents the current segment of the workout. The
height of the flashing segment indicates the speed
setting for the current segment. At the end of each
segment, a series of tones will sound. If a different
speed and/or incline setting is programmed for the
next segment of the workout, the new speed and/or
incline setting will flash in the display to alert you.
The treadmill will then automatically adjust to the
speed and/or incline setting for the next segment.
See HOW TO TURN ON THE POWER on page
16.
2. Select one of the preset workouts.
To select one
of the sixteen
The workout will continue in this way until the last
segment of the profile flashes in the display and
the last segment ends. The walking belt will then
slow to a stop.
preset work-
outs, press
the Workout
Select button
below the desired workout repeatedly until the de-
sired workout appears in the upper display.
If the speed or incline setting for the current seg-
ment is too high or too low, you can manually over-
ride the setting by pressing the speed or incline
buttons; however, when the current segment of
the workout ends, the treadmill will automati-
cally adjust to the speed and incline settings
for the next segment.
As each pre-
set workout
is selected,
the maximum
speed setting
and the max-
To change the intensity level of the entire program,
press the Intensity increase and decrease buttons.
imum incline setting of the workout will flash in the
lower display for a few seconds. In addition, the
duration of the workout will appear in the display
and a profile of the speed settings of the workout
will scroll across the upper display.
To stop the workout at any time, press the Stop
button. To restart the workout, press the Start but-
ton or the Speed increase button. The walking belt
will begin to move at 1 mph. When the next seg-
ment of the workout begins, the treadmill will auto-
matically adjust to the speed and incline settings
for that segment.
3. Start the walking belt.
Press the Start button or the Speed increase but-
ton to start the workout. A moment after you press
the button, the treadmill will automatically adjust to
the first speed and incline settings for the workout.
Hold the handrails and begin walking.
4. Follow your progress with the displays.
See step 5 on page 17.
Each workout is divided into one-minute segments.
One speed setting and one incline setting are pro-
grammed for each segment. Note: The same
speed setting and/or incline setting may be pro-
grammed for consecutive segments.
5. Measure your heart rate if desired.
See step 6 on page 17.
6. Turn on the fan if desired.
See step 7 on page 17.
During the work-
out, the profile will
show your
7. When you are finished exercising, remove the
key from the console.
progress. The
flashing segment
of the profile rep-
Current Segment
See step 8 on page 17.
18
Download from Www.Somanuals.com. All Manuals Search And Download.
HOW TO USE AN IFIT WORKOUT
3. Start the walking belt.
telephone number on the front cover of this manual.
iFit cards are also available at select stores.
Press the Start button or the Speed increase but-
ton to start the workout. A moment after you press
the button, the treadmill will automatically adjust to
the first speed and incline settings of the workout.
Hold the handrails and begin walking.
1. Insert the key into the console.
See HOW TO TURN ON THE POWER on page
16.
During the workout, a personal trainer will guide
you through the workout. You can select an audio
setting for your personal trainer (see THE INFOR-
MATION MODE on page 20).
2. Insert an iFit card and select a workout.
To use an iFit workout, insert an iFit card into the
iFit slot; make sure that the iFit card is oriented so
the metal contacts are face-down and are inserted
into the iFit slot. When the iFit card is properly in-
serted, the iFit logo will light.
If the speed or incline setting for the current seg-
ment is too high or too low, you can manually over-
ride the setting by pressing the speed or incline
buttons; however, when the next segment be-
gins, the treadmill will automatically adjust to
the speed and incline settings for the next seg-
ment.
iFit Slot
iFit Logo
To stop the workout at any time, press the Stop
button. To restart the workout, press the Start but-
ton or the Speed increase button. The walking belt
will begin to move. When the next segment of the
workout begins, the treadmill will automatically ad-
just to the speed and incline settings for the next
segment.
iFit Card
4. Follow your progress with the displays.
See step 5 on page 17.
Next, select an iFit workout by pressing the iFit in-
crease and decrease buttons next to the iFit slot.
When an iFit workout is selected, the maximum
speed setting and the maximum incline setting of
the workout will flash in the lower display for a few
seconds. In addition, the duration of the workout
will appear in the display and a profile of the speed
settings of the workout will scroll across the upper
display.
5. Turn on the fan if desired.
See step 7 on page 17.
6. When you are finished exercising, remove the
key from the console.
Each iFit workout is divided into several one-
minute segments. One speed setting and one in-
cline setting are programmed for each segment.
Note: The same speed and/or incline setting may
be programmed for consecutive segments.
See step 8 on page 17.
CAUTION: Always remove iFit cards from the
iFit slot when you are not using them.
19
Download from Www.Somanuals.com. All Manuals Search And Download.
THE INFORMATION MODE
HOW TO USE THE STEREO SOUND SYSTEM
The console features an information mode that keeps
track of treadmill usage information. The information
mode also allows you to select miles or kilometers as
the unit of measurement and to turn on and turn off the
demo mode.
To play music or audio books through the consoleʼs
stereo speakers, you must connect your MP3 player,
CD player, or other personal audio player to the con-
sole through the audio jack.
To use the audio jack, locate the audio wire and plug it
into the audio jack near the iFit slot. Then, plug the
audio wire into a jack on your MP3 player, CD player,
or other personal audio player. Make sure that the
audio wire is fully inserted.
To select the information mode, hold down the Stop
button, insert the key into the console, and then re-
lease the Stop button. When the information mode is
selected, the following information will appear in the
display:
Next, press the Play button on your MP3 player, CD
player, or other personal audio player. Adjust the vol-
ume on your personal audio player.
The upper left
corner of the
lower display will
show the num-
If you are using a personal CD player and the CD
skips, set the CD player on the floor or another flat sur-
face instead of on the console.
ber of hours that
the treadmill has
been operated. The lower right corner of the display
will show the total number of miles or kilometers that
the walking belt has moved. In addition, an “E” for
English miles or an “M” for metric kilometers will ap-
HOW TO USE THE CROSSWALK ARMS
pear in the upper right corner of the display. To change As you walk on the treadmill, you can hold the
the unit of measurement, press the Speed increase
button. The lower left corner of the display will show
the volume level. To change the volume level, press
the Incline increase button.
handrails or use the crosswalk arms. To exercise your
arms, shoulders, and back for a total body workout,
move the crosswalk arms forward and back as you
walk on the treadmill.
The console fea-
To vary the intensity of your upper body exercise, the
resistance of the crosswalk arms can be adjusted. To
increase the resistance, turn the resistance knobs
clockwise; to decrease the resistance, turn the knobs
counterclockwise.
tures a display
demo mode, de-
signed to be
used if the tread-
mill is displayed
in a store. While the demo mode is turned on, the con-
sole will function normally when you plug in the power
cord, switch the reset/off circuit breaker to the reset
position, and insert the key into the console. However,
when you remove the key, the displays will remain lit,
although the buttons will not function. If the demo
mode is turned on, a “d” will appear in the upper dis-
play while the information mode is selected. To turn on
or turn off the demo mode, press the Speed decrease
button.
Crosswalk
Arms
You can select an audio setting if desired. When you
use an iFit card, a personal trainer will guide you
through your workouts. If a “P” appears in the upper
display, the personal trainer will give you detailed in-
structions. If no “P” appears, your personal trainer will
simply guide you through your iFit workouts. To
change the audio setting, press the Incline decrease
button.
Resistance
Knobs
To exit the information mode, remove the key from the
console.
20
Download from Www.Somanuals.com. All Manuals Search And Download.
HOW TO FOLD AND MOVE THE TREADMILL
HOW TO FOLD THE TREADMILL FOR STORAGE
1
Before folding the treadmill, adjust the incline to the
lowest position. If you do not do this, you may damage the
treadmill when you fold it. Remove the key and unplug the
power cord. CAUTION: You must be able to safely lift 45
lbs. (20 kg) to raise, lower, or move the treadmill.
Frame
1. Hold the metal frame firmly in the location shown by
the arrow at the right. CAUTION: To decrease the pos-
sibility of injury, do not lift the frame by the plastic
foot rails. Make sure to bend your legs and keep your
back straight as you raise the frame. Raise the frame
about halfway to the vertical position.
2. Raise the frame until the latch knob locks into the storage
2
position. Make sure that the latch knob is locked in the
storage position.
Frame
To protect the floor or carpet from damage, place a
mat under the treadmill. Keep the treadmill out of di-
rect sunlight. Do not leave the treadmill in the storage
Latch
Knob
position in temperatures above 85° F (30° C).
HOW TO MOVE THE TREADMILL
Before moving the treadmill, convert the treadmill to the stor-
age position as described above. Make sure that the latch
knob is locked in the storage position.
Handrail
1. Hold a handrail and place one foot against one of the
wheels.
2. Tip the treadmill back until it rolls freely on the wheels.
Carefully move the treadmill to the desired location. Never
move the treadmill without tipping it back. To reduce
the risk of injury, use extreme caution while moving
the treadmill. Do not attempt to move the treadmill
over an uneven surface.
Wheel
3. Place one foot against a wheel, and carefully lower the
treadmill until it is resting in the storage position.
HOW TO LOWER THE TREADMILL FOR USE
1. See drawing 2. Hold the upper end of the treadmill with your right hand. Pull the latch knob to the left and hold
it. It may be necessary to push the frame forward as you pull the knob to the left. Pivot the frame downward
and release the latch knob.
2. See drawing 1. Hold the metal frame firmly with both hands and lower it to the floor. CAUTION: Do not
grip only the plastic foot rails or drop the frame to the floor. Bend your legs and keep your back
straight.
21
Download from Www.Somanuals.com. All Manuals Search And Download.
TROUBLESHOOTING
Most treadmill problems can be solved by following the steps below. Find the symptom that applies, and
follow the steps listed. If further assistance is needed, please see the front cover of this manual.
PROBLEM: The power does not turn on
SOLUTION: a. Make sure that the power cord is plugged into a surge suppressor, and that the surge suppressor
is plugged into a properly grounded outlet (see page 14). Use only a single-outlet surge suppres-
sor that meets all of the specifications described on page 14. IMPORTANT: The treadmill is not
compatible with GFCI-equipped outlets.
b. After the power cord has been plugged in, make sure that the key is inserted into the console.
c. Check the reset/off circuit breaker located on the
c
treadmill frame near the power cord. If the switch
protrudes as shown, the circuit breaker has
tripped. To reset the circuit breaker, wait for five
minutes and then press the switch back in.
Reset
Tripped
PROBLEM: The power turns off during use
SOLUTION: a. Check the reset/off circuit breaker (see the drawing above). If the circuit breaker has tripped, wait
for five minutes and then press the switch back in.
b. Make sure that the power cord is plugged in. If the power cord is plugged in, unplug it, wait for
five minutes, and then plug it back in.
c. Remove the key from the console. Reinsert the key into the console.
d. If the treadmill still will not run, please see the front cover of this manual.
PROBLEM: The console displays remain lit when you remove the key from the console
SOLUTION: a. The console features a display demo mode, designed to be used if the treadmill is displayed in a
store. If the displays remain lit when you remove the key, the demo mode is turned on. To turn off
the demo mode, hold down the Stop button for a few seconds. If the displays are still lit, see THE
INFORMATION MODE on page 20 to turn off the demo mode.
PROBLEM: The displays of the console do not function properly
SOLUTION: a. Remove the key from the console and UNPLUG
a
77
THE POWER CORD. With the help of a second
person, carefully tip the Uprights (77, 79) down.
There may be three #8 x 2" Screws (24) in the bot-
tom of the Belly Pan (70). If there are, remove
them. Note: A Phillips screwdriver with a shaft at
least 5 in. (13 cm) long is required. Then, raise the
Uprights.
70
24
79
24
22
Download from Www.Somanuals.com. All Manuals Search And Download.
Remove the three #8 x 3/4" Screws (1) and care-
fully pivot the Motor Hood (63) off.
1
63
Locate the Reed Switch (68) and the Magnet (48)
on the left side of the Pulley (47). Turn the Pulley
until the Magnet is aligned with the Reed Switch.
Make sure that the gap between the Magnet and
the Reed Switch is about 1/8 in. (3 mm). If nec-
essary, loosen the 3/4" Screw (16), move the Reed
Switch slightly, and then retighten the Screw.
Top
View
1/8 in.
16
48
47
68
Reattach the Motor Hood (not shown) with the #8 x
3/4" Screws (not shown). Reattach the #8 x 2"
Screws (not shown) if necessary. Run the treadmill
for a few minutes to check for a correct speed
reading.
PROBLEM: The incline of the treadmill does not change correctly
SOLUTION: a. With the key in the console, press one of the Incline buttons. While the incline is changing, re-
move the key. After a few seconds, re-insert the key. The treadmill will automatically rise to the
maximum incline level and then return to the minimum level. This will recalibrate the incline system.
PROBLEM: The walking belt slows when walked on
SOLUTION: a. Use only a single-outlet surge suppressor that meets all of the specifications described on page 14.
b. If the walking belt is overtightened, treadmill perfor-
b
mance may decrease and the walking belt may be-
2–3 in.
come damaged. Remove the key and UNPLUG
THE POWER CORD. Using the hex key, turn both
idler roller bolts counterclockwise, 1/4 of a turn.
When the walking belt is properly tightened, you
should be able to lift each edge of the walking belt
2 to 3 in. (5 to 7 cm) off the walking platform. Be
careful to keep the walking belt centered. Then,
plug in the power cord, insert the key, and run the
treadmill for a few minutes. Repeat until the walking
belt is properly tightened.
Idler Roller Bolts
c. If the walking belt still slows when walked on, see the front cover of this manual.
23
Download from Www.Somanuals.com. All Manuals Search And Download.
PROBLEM: The walking belt is off-center or slips when walked on
SOLUTION: a. If the walking belt is off-center, first remove the
key and UNPLUG THE POWER CORD. If the
walking belt has shifted to the left, use the hex
key to turn the left idler roller bolt clockwise 1/2 of a
turn; if the walking belt has shifted to the right,
turn the bolt counterclockwise 1/2 of a turn. Be
careful not to overtighten the walking belt. Then,
plug in the power cord, insert the key, and run the
treadmill for a few minutes. Repeat until the walk-
ing belt is centered.
a
b. If the walking belt slips when walked on, first re-
move the key and UNPLUG THE POWER CORD.
Using the hex key, turn both idler roller bolts clock-
wise, 1/4 of a turn. When the walking belt is cor-
rectly tightened, you should be able to lift each
edge of the walking belt 2 to 3 in. (5 to 7 cm) off
the walking platform. Be careful to keep the walk-
ing belt centered. Then, plug in the power cord, in-
sert the key, and carefully walk on the treadmill for
a few minutes. Repeat until the walking belt is
properly tightened.
b
PROBLEM: The crosswalk arms squeak during use
SOLUTION: a. (Note: Correcting this problem requires a small
amount of white marine grease, available at hard-
ware stores.) Turn the Resistance Knob (110)
counterclockwise and remove it. Next, remove the
Resistance Cone (108) with the Crosswalk Arm
(98).
a
98
110
108
Apply a thin layer of white marine grease to the
outer surface of the Resistance Cone (108). Then,
reattach the Resistance Cone with the Crosswalk
Arm (98) and the Resistance Knob (110).
24
Download from Www.Somanuals.com. All Manuals Search And Download.
EXERCISE GUIDELINES
Burning Fat—To burn fat effectively, you must exer-
cise at a low intensity level for a sustained period of
time. During the first few minutes of exercise, your
body uses carbohydrate calories for energy. Only after
the first few minutes of exercise does your body begin
to use stored fat calories for energy. If your goal is to
burn fat, adjust the intensity of your exercise until your
heart rate is near the lowest number in your training
zone. For maximum fat burning, exercise with your
heart rate near the middle number in your training
zone.
WARNING:
Before beginning this
or any exercise program, consult your physi-
cian. This is especially important for persons
over age 35 or persons with pre-existing
health problems.
The pulse sensor is not a medical device.
Various factors may affect the accuracy of
heart rate readings. The pulse sensor is in-
tended only as an exercise aid in determining
heart rate trends in general.
Aerobic Exercise—If your goal is to strengthen your
cardiovascular system, you must perform aerobic exer-
cise, which is activity that requires large amounts of
oxygen for prolonged periods of time. For aerobic ex-
ercise, adjust the intensity of your exercise until your
heart rate is near the highest number in your training
zone.
These guidelines will help you to plan your exercise
program. For detailed exercise information, obtain a
reputable book or consult your physician. Remember,
proper nutrition and adequate rest are essential for
successful results.
WORKOUT GUIDELINES
EXERCISE INTENSITY
Warming Up—Start with 5 to 10 minutes of stretching
and light exercise. A warm-up increases your body
temperature, heart rate, and circulation in preparation
for exercise.
Whether your goal is to burn fat or to strengthen your
cardiovascular system, exercising at the proper inten-
sity is the key to achieving results. You can use your
heart rate as a guide to find the proper intensity level.
The chart below shows recommended heart rates for
fat burning and aerobic exercise.
Training Zone Exercise—Exercise for 20 to 30 min-
utes with your heart rate in your training zone. (During
the first few weeks of your exercise program, do not
keep your heart rate in your training zone for longer
than 20 minutes.) Breathe regularly and deeply as you
exercise–never hold your breath.
Cooling Down—Finish with 5 to 10 minutes of stretch-
ing. Stretching increases the flexibility of your muscles
and helps to prevent post-exercise problems.
EXERCISE FREQUENCY
To find the proper intensity level, find your age at the
bottom of the chart (ages are rounded off to the near-
est ten years). The three numbers listed above your
age define your “training zone.” The lowest number is
the heart rate for fat burning, the middle number is the
heart rate for maximum fat burning, and the highest
number is the heart rate for aerobic exercise.
To maintain or improve your condition, complete three
workouts each week, with at least one day of rest be-
tween workouts. After a few months of regular exer-
cise, you may complete up to five workouts each
week, if desired. Remember, the key to success is to
make exercise a regular and enjoyable part of your
everyday life.
25
Download from Www.Somanuals.com. All Manuals Search And Download.
PART LIST—Model No. RCTL07809.0
To locate the parts listed below, see the EXPLODED DRAWING near the end of this manual.
R1009A
Key No. Qty.
Description
Key No. Qty.
Description
1
26
4
3
6
4
2
2
1
6
2
3
4
5
4
2
11
2
2
2
1
1
2
8
3
8
2
4
2
2
2
4
4
3
2
1
1
1
2
1
2
1
1
2
2
2
1
1
1
1
1
#8 x 3/4" Screw
#8 x 1" Tek Screw
3/8" x 2" Bolt
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
85
86
87
88
89
90
91
92
93
94
95
96
97
98
99
100
1
1
1
2
1
2
1
2
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
3
1
2
1
1
1
1
1
4
2
1
2
4
2
2
4
2
10
1
1
1
1
2
1
1
Latch Knob
2
Right Foot Rail
Frame
3
4
5/16" x 3/4" Bolt
3/8" x 4" Bolt
Roller Bracket
Idler Roller Ground Wire
Crosswalk Arm Handgrip
Right Rear Foot
Resistance Cone Insert
Left Rear Foot
Base
5
6
1/4" x 1 1/4" Bolt
5/16" x 1 1/2" Bolt
3/8" x 1 3/4" Bolt
5/16" Star Washer
1/4" Star Washer
3/8" Locknut
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
Idler Roller
3/8" Star Washer
#8 x 3/4" Tek Screw
#8 x 1 1/2" Screw
#8 x 1/2" Controller Screw
3/4" Screw
Hood Accent
Motor Hood
Lift Frame
Lift Frame Ground Wire
Drive Motor Belt
Drive Motor
5/16" x 3 5/8" Bolt
3/8" x 1" Bolt
Reed Switch
Idler Roller Bolt
3/8" x 1 1/2" Incline Motor Bolt
3/8" x 1 3/4" Incline Motor Bolt
3/8" x 3/4" Bolt
#8 x 1/2" Screw
#8 x 2" Screw
Reed Switch Clamp
Belly Pan
Reset/Off Circuit Breaker
Power Cord Grommet
Power Cord
Controller
#12 x 1 1/4" Screw
Motor Bolt
Controller Ground Wire
Wire Tie
Belt Guide Screws
1/4" Flat Washer
1/4" Split Washer
Cage Nut
Left Upright
Arm Insert
Right Upright
Lift Motor Spacer
Lift Motor
3/8" Locknut
5/16" Flange Nut
Hood Clip
Left Upright Spacer
Right Upright Spacer
Bolt Spacer
Small Cap
Hex Key
Base Cap
5/32" Hex Key
Left Foot Rail
Upright Wire
Caution Decal
Base Foot
Foot Rail Decal
Latch Warning Decal
Platform Cushion
Walking Platform
Walking Belt
Base Foot Spacer
Wheel
Releasable Tie
15 1/2" Cable Tie
8" Cable Tie
Belt Guide
Frame Cap
Left Accessory Tray
Audio Wire
Frame Spacer
1/4" x 1" Bolt
Console Base
Console
Drive Roller/Pulley
Magnet
Crosswalk Arm
Right Accessory Tray
Console Crossbar
Latch Cap
Storage Latch
26
Download from Www.Somanuals.com. All Manuals Search And Download.
Key No. Qty.
Description
Key No. Qty.
Description
101
102
103
104
105
106
107
108
109
110
1
1
1
4
1
1
1
2
1
2
Left Handrail
Access Door
Key/Clip
111
2
2
2
1
–
–
–
–
–
–
Upright Insert
112
3/8" x 4 3/4" Bolt
iFit Card
113
Handrail Cap
Right Handrail
Lift Motor Wire
Console Wire Tie
Resistance Cone
Console Fan
Resistance Knob
114
French Latch Decal
4" Green Wire, M/R
8" Blue Wire, M/F
10" Blue Wire, 2F
12" Red Wire, M/F
10" Black Wire, M/F
Userʼs Manual
*
*
*
*
*
*
Note: Specifications are subject to change without notice. For information about ordering replacement parts, see
the back cover of this manual. *These parts are not illustrated.
27
Download from Www.Somanuals.com. All Manuals Search And Download.
EXPLODED DRAWING A—Model No. RCTL07809.0
R1009A
9
4
4
5
4
4
5
2
6
4
2
3
8
3
4
3
7
2
5
2
0
6
4
1
8
4
7
4
5
2
1
5
1
4
4
2
4
5
4
1
1
7
5
2
5
2
3
2
3
5
2
4
4
5
3
2
7
4
3
2
7
6
5
5
1
5
5
2
1
4
3
8
2
4
6
3
1
1
0
4
7
3
5
9
9
2
3
6
5
1
2
3
6
3
6
1
5
3
4
3
1
4
2
5
5
2
28
Download from Www.Somanuals.com. All Manuals Search And Download.
EXPLODED DRAWING B—Model No. RCTL07809.0
R1009A
1
33
1
33
1
33
92
63
93
62
91
26
64
23
65
18
66
23
76
31
15
21
67
23
81
18
20
75
23
106
31
74
80
73
13
16
69
13
72
71
68
13
13
24
70
24
24
29
Download from Www.Somanuals.com. All Manuals Search And Download.
EXPLODED DRAWING C—Model No. RCTL07809.0
R1009A
56
15
56
15
4
98
9
4
98
77
9
4
111
1
86
110
4
9
1
4
34
112
9
5
108
58
78
31
112
85
82
78
12
79
108
58
22
1
34
1
84
87
110
88
60
111
31
2
85
3
22
86
87
89
88
2
11
12
5
90
88
83
11
2
84
89
88
2
90
3
30
Download from Www.Somanuals.com. All Manuals Search And Download.
EXPLODED DRAWING D—Model No. RCTL07809.0
R1009A
95
113
97
109
94
1
23
1
96
1
103
99
1
1
107
1
1
104
1
102
1
1
104
14
101
6
14
10
100
1
30
104
6
10
105
30
104
31
Download from Www.Somanuals.com. All Manuals Search And Download.
ORDERING REPLACEMENT PARTS
To order replacement parts, please see the front cover of this manual. To help us assist you, be prepared to pro-
vide the following information when contacting us:
• the model number and serial number of the product (see the front cover of this manual)
• the name of the product (see the front cover of this manual)
• the key number and description of the replacement part(s) (see the PART LIST and the EXPLODED
DRAWING near the end of this manual)
LIMITED WARRANTY
ICON of Canada, Inc. (ICON) warrants this product to be free from defects in workmanship and material,
under normal use and service conditions. The frame is warranted for a lifetime. The drive motor is war-
ranted for twenty-five (25) years from the date of purchase. Parts and labor are warranted for one (1)
year from the date of purchase.
This warranty extends only to the original purchaser. ICONʼs obligation under this warranty is limited to
repairing or replacing, at ICONʼs option, the product through one of its authorized service centers. All re-
pairs for which warranty claims are made must be preauthorized by ICON. This warranty does not extend
to any damage to a product caused by or attributable to freight damage, abuse, misuse, improper or ab-
normal usage, or repairs not provided by an ICON authorized service center; products used for commer-
cial or rental purposes; or products used as store display models. No other warranty beyond that specifi-
cally set forth above is authorized by ICON.
ICON is not responsible or liable for indirect, special, or consequential damages arising out of or in con-
nection with the use or performance of the product; damages with respect to any economic loss, loss of
property, loss of revenues or profits, loss of enjoyment or use, or costs of removal or installation; or other
consequential damages of whatsoever nature. Some provinces do not allow the exclusion or limitation of
incidental or consequential damages. Accordingly, the above limitation may not apply to you.
The warranty extended hereunder is in lieu of any and all other warranties, and any implied warranties of
merchantability or fitness for a particular purpose are limited in their scope and duration to the terms set
forth herein. Some provinces do not allow limitations on how long an implied warranty lasts. Accordingly,
the above limitation may not apply to you.
This warranty gives you specific legal rights. You may also have other rights that vary from province to
province.
ICON of Canada, Inc., 900 de lʼIndustrie, St. Jérôme, QC J7Y 4B8
Part No. 291734 R1009A
Printed in USA © 2009 ICON IP, Inc.
Download from Www.Somanuals.com. All Manuals Search And Download.
|