Model No. RBEL9906.0
Serial No.
USER’S MANUAL
Serial
Number
Decal
QUESTIONS?
As a manufacturer, we are com-
mitted to providing complete
customer satisfaction. If you
have questions, or if parts are
damaged or missing, PLEASE
CONTACT OUR CUSTOMER
SERVICE DEPARTMENT
DIRECTLY.
CALL TOLL-FREE:
1-877-994-4999
Mon.–Fri., 6 a.m.–6 p.m. MST
ON THE WEB:
CAUTION
Visit our website at
Read all precautions and instruc-
tions in this manual before using
this equipment. Keep this manual
for future reference.
new products, prizes,
fitness tips, and much more!
Download from Www.Somanuals.com. All Manuals Search And Download.
IMPORTANT PRECAUTIONS
WARNING:
To reduce the risk of serious injury, read the following important precau-
tions before using the elliptical exerciser.
1. Read all instructions in this manual and all
warnings on the elliptical exerciser before
using the elliptical exerciser. Use the ellipti-
cal exercise only as described in this
manual.
8. Wear appropriate exercise clothes while
using the elliptical exerciser. Always wear
athletic shoes for foot protection while exer-
cising.
9. Hold the handgrip pulse sensors or the upper
body arms when mounting, dismounting, or
using the elliptical exerciser.
2. It is the responsibility of the owner to ensure
that all users of the elliptical exerciser are
adequately informed of all precautions.
10. The pulse sensor is not a medical device.
Various factors may affect the accuracy of
heart rate readings. The pulse sensor is
intended only as an exercise aid in determin-
ing heart rate trends in general.
3. The elliptical exerciser is intended for
home use only. Do not use the elliptical
exerciser in a commercial, rental, or institu-
tional setting.
4. Keep the elliptical exerciser indoors, away
from moisture and dust. Place the elliptical
exerciser on a level surface, with a mat
beneath it to protect the floor or carpet.
Make sure that there is enough clearance
around the elliptical exerciser to mount, dis-
mount, and use it.
11. Keep your back straight while using the ellip-
tical exerciser; do not arch your back.
12. If you feel pain or dizziness while exercising,
stop immediately and cool down.
13. When you stop exercising, allow the pedals
to slowly come to a stop.
5. Inspect and properly tighten all parts regu-
larly. Replace any worn parts immediately.
14. The warning decals shown on page 4 have
been placed on the elliptical exerciser in the
locations shown. If a decal is missing or
illegible, call the toll-free telephone number
on the front cover of this manual and order
a free replacement decal. Apply the decal in
the location shown.
6. Keep children under age 12 and pets away
from the elliptical exerciser at all times.
7. The elliptical exerciser should not be used
by persons weighing more than 325 pounds.
WARNING:
Before beginning this or any exercise program, consult your physician.
This is especially important for persons over the age of 35 or persons with pre-existing health prob-
lems. Read all instructions before using. ICON assumes no responsibility for personal injury or
property damage sustained by or through the use of this product.
3
Download from Www.Somanuals.com. All Manuals Search And Download.
BEFORE YOU BEGIN
®
Thank you for purchasing the revolutionary REEBOK
1000 ZX elliptical exerciser. The 1000 ZX elliptical
exerciser provides an array of features designed to
make your workouts at home more effective and
enjoyable—and when you’re not exercising, the
tacting us. The model number is RBEL9906.0. The
serial number can be found on a decal attached to the
elliptical exerciser (see the front cover of this manual
for the location of the decal).
unique elliptical exerciser can be folded out of the way.
To avoid a registration fee for any service needed
under warranty, you must register the elliptical
For your benefit, read this manual carefully before
you use the elliptical exerciser. If you have ques-
tions after reading this manual, please see the front
cover of this manual. To help us assist you, note the
product model number and serial number before con-
Before reading further, please familiarize yourself with
the parts that are labeled in the drawing below.
Fan
Console
Upper Body Arm
Stereo Speakers
Pulse Sensor
Stereo Cable
Water Bottle Holder*
Storage Magnet
FRONT
Ramp
Wheel
Pedal
Pedal Disc
Pedal Arm Latch
Leveling Foot
Latch Button
RIGHT SIDE
Handle
Power Socket
REAR
*No water bottle is included
4
Download from Www.Somanuals.com. All Manuals Search And Download.
ASSEMBLY
To hire an authorized service technician to assemble the elliptical exerciser, call toll-free 1-800-445-2480.
Assembly requires two persons. Place all parts of the elliptical exerciser in a cleared area and remove the
packing materials. Do not dispose of the packing materials until assembly is completed.
Assembly requires the included hex keys and your own phillips screwdriver
mallet
and rubber
.
As you assemble the elliptical exerciser, use the drawings below to identify small parts. The number in parentheses
below each drawing is the key number of the part, from the PART LIST on pages 24 and 25. The number follow-
ing the parentheses is the quantity needed for assembly. Note: Some small parts may have been preassem-
bled. If a part is not in the parts bag, check to see if it has been preassembled.
M8.5 x 16mm x
M6 Split Washer
(102)–8
M8 Split
M10 x 25mm
M10 Curved
Link Arm
1.5mm Washer
(103)–6
Washer (87)–2
Washer (99)–4
Spacer (74)–4
Washer (101)–4
M4 x 16mm
M6 x 35mm
Screw (109)–4
M6 x 62mm
Screw (108)–4
Screw (116)–16
Wave Washer
(100)–2
M8 x 15mm Button
Screw (106)–10
M8 x 20mm Button
Screw (107)–4
M8 x 25mm Button
Screw (110)–2
M10 x 20mm Button
Screw (111)–2
M10 x 93mm Button Screw (82)–4
1. While another person lifts the front of the
1
Frame (1), attach the Front Stabilizer (4) to the
Frame with two M10 x 93mm Button Screws
(82) and two M10 Curved Washers (99).
82
99
1
99
4
5
Download from Www.Somanuals.com. All Manuals Search And Download.
2. While another person lifts the Folding Frame (2),
attach the Rear Stabilizer (3) to the Folding
Frame with two M10 x 93mm Button Screws (82)
and two M10 Curved Washers (99). Next,
2
1
tighten the Center Foot (95) into the Frame (1).
3
95
99
82
2
99
3. Attach the Front Ramp Cover (6) to the
Ramp (5) with four M4 x 16mm Screws (116).
3
6
Slide an M10 x 25mm Washer (87) onto an
M10 x 20mm Button Screw (111). Tighten the
Button Screw into one end of the Ramp
Axle (72). Apply a small amount of the included
grease to the Ramp Axle.
Orient the Ramp (5) as shown. Align the lower
end of the Ramp with the welded tube on the
Frame (1). Insert the Ramp Axle (72) into the
Ramp and the welded tube.
5
Slide an M10 x 25mm Washer (87) onto an
M10 x 20mm Button Screw (111). Tighten the
Button Screw into the open end of the Ramp
Axle (72).
116
87
111
1
72
87
111
Grease
6
Download from Www.Somanuals.com. All Manuals Search And Download.
4. Identify the Left Pedal (34) and the Left Pedal
Arm (32), which are marked with stickers.
4
34
Attach the Left Pedal (34) to the Left Pedal
Arm (32) with two M6 x 62mm Screws (108),
two M6 x 35mm Screws (109), and four M6
Split Washers (102).
32
Attach the Right Pedal (not shown) to the
Right Pedal Arm (not shown) in the same
way.
102
109
102
109
108
102
5. Insert the Roller (38) on the Left Pedal Arm (32)
and the Roller on the Right Pedal Arm (33) into
the sides of the Ramp (5).
5
116
7
Attach the Rear Ramp Cover (7) to the
Ramp (5) with two M4 x 16mm Screws (116).
33
See the inset drawing. Lift the Pedal Arm
Latch (41) on the Left Pedal Arm (32) and set
the end of the Left Pedal Arm on the left Crank
Bushing Sleeve (54). Release the Pedal Arm
Latch; make sure that the Left Pedal Arm is
securely connected to the Crank Bushing
Sleeve.
38
5
Connect the Right Pedal Arm (33) to the
right Crank Bushing Sleeve (not shown) in
the same way.
32
32
41
54
7
Download from Www.Somanuals.com. All Manuals Search And Download.
6. While another person holds the Upright (10)
near the Frame (1), connect the Upper Wire
Harness (65) to the Lower Wire Harness (64).
6
Carefully insert the Upright (10) into the
Frame (1); be careful not to damage the Wire
Harnesses (64, 65). Attach the Upright with four
M8 x 20mm Button Screws (107) and four M8
Split Washers (101).
Be careful not
to damage the
Wire Harnesses
(64, 65) during
this step.
10
65
64
107
101
101
1
107
7. Attach the Left Upper Body Arm (22) to the left
Upper Body Leg (24) with three M8 x 15mm
Button Screws (106).
7
23
Attach the Right Upper Body Arm (23) in the
same way.
22
106
24
8
Download from Www.Somanuals.com. All Manuals Search And Download.
8. Hold the Left Rear Upper Body Cover (26) and
the Left Front Upper Body Cover (27) around
the left Upper Body Leg (24). Attach the Upper
Body Covers with five M4 x 16mm Screws (116).
8
29
26
116
28
Attach the Right Rear Upper Body Cover (28)
and the Right Front Upper Body Cover (29)
in the same way.
27
24
116
9. Apply a small amount of grease to the axle on
the Left Link Arm (30), to the axle on the Left
Pedal Arm (32), and to a Wave Washer (100).
9
24
Slide the Wave Washer (100) onto the axle on
the Left Pedal Arm (32). Next, slide a Link Arm
Spacer (74) onto the axle on the Left Link
Arm (30).
31
74
Grease
Then, insert the axle on the Left Link Arm (30)
into the left Upper Body Leg (24) while sliding
the Left Link Arm onto the axle on the Left Pedal
Arm (32).
100
30
Repeat this step with the Right Link Arm (31).
32
Grease
9
Download from Www.Somanuals.com. All Manuals Search And Download.
10. Attach the Left Link Arm (30) to the Left Pedal
Arm (32) with an M8 x 15mm Button Screw
(106), an M8.5 x 16mm x 1.5mm Washer (103),
and an Axle Cover (66).
10
24
31
Attach the Left Link Arm (30) to the left Upper
Body Leg (24) with an M8 x 25mm Button
Screw (110), two M8.5 x 16mm x 1.5mm
Washers (103), two Axle Covers (66), a Link
Arm Spacer (74), and an M8 x 15mm Button
Screw (106) as shown.
106
103
66
74
66
103
110
Attach the Right Link Arm (31) in the same
way.
30
106
66
103
32
11. Plug the power cord (not shown) into the power socket (not shown) at the rear of the elliptical exer-
ciser.
Make sure that all parts of the elliptical exerciser are properly tightened. Note: Some hardware may be
left over after assembly is completed. To protect the floor or carpet from damage, place a mat under the
elliptical exerciser.
10
Download from Www.Somanuals.com. All Manuals Search And Download.
HOW TO USE THE ELLIPTICAL EXERCISER
HOW TO PLUG IN THE POWER CORD
HOW TO FOLD AND UNFOLD THE ELLIPTICAL
EXERCISER
This product must be grounded. If it should mal-
function or break down, grounding provides a path of
least resistance for electric current to reduce the risk
of electric shock. This product is equipped with a cord
having an equipment-grounding conductor and a
grounding plug. Plug the power cord into an appro-
priate outlet that is properly installed and ground-
ed in accordance with all local codes and ordi-
nances. This product is for use on a nominal 120-
volt circuit. Important: The elliptical exerciser is
not compatible with GFCI-equipped outlets.
When the elliptical exerciser is not in use, the frame
can be folded out of the way. First, lift the latch under
each pedal arm, and lift the pedal arms off the sleeves
on the crank arms.
Pedal
Sleeve
Arm
DANGER:
Improper connection
Latch
of the equipment-grounding conductor can
result in an increased risk of electric shock.
Check with a qualified electrician or service-
man if you are in doubt as to whether the
product is properly grounded. Do not modify
the plug provided with the product—if it will
not fit the outlet, have a proper outlet
Next, raise the pedal arms until they touch the magnets
on the upper body legs; the magnets will hold the pedal
arms in place. Then, hold the handle and lift the frame
until it locks in a vertical position.
installed by a qualified electrician.
Magnet
A temporary
adapter may
Grounded Outlet Box
Handle
Pedal Arm
be used to
connect the
power cord
to a 2-pole
receptacle
as shown at
the right if a
properly
Adapter
Latch
Lug
Button
Metal Screw
grounded
outlet is not
available. The temporary adapter should be used only
until a properly grounded outlet can be installed by a
qualified electrician.
The green-colored rigid ear, lug, or the like extending
from the adapter must be connected to a permanent
ground such as a properly grounded outlet box cover.
To use the elliptical exerciser, first hold the handle,
press the latch button, and lower the frame.
Whenever the adapter is used, it must be held in place Next, pull the pedal arms off the magnets on the upper
by a metal screw. Some 2-pole receptacle outlet box body legs. Then, lift the latches under the pedal
covers are not grounded. Contact a qualified elec-
trician to determine if the outlet box cover is
grounded before using an adapter.
arms, and set the pedal arms on the sleeves on the
crank arms. Release the latches, and make sure that
the pedal arms are securely connected to the crank
arms.
11
Download from Www.Somanuals.com. All Manuals Search And Download.
HOW TO MOVE THE ELLIPTICAL EXERCISER
HOW TO EXERCISE ON THE ELLIPTICAL
EXERCISER
To move the elliptical exerciser, first fold it as
described at the left. Next, stand in front of the ellipti-
cal exerciser, hold the handgrip pulse sensors, and
To mount the elliptical exerciser, hold the upper body
arms and step onto the pedal that is in the lowest posi-
place one foot against the center of the front stabilizer. tion. Next, step onto the other pedal. Push the pedals
Pull the pulse sensors until the elliptical exerciser will
roll on the front wheels. Carefully move the elliptical
exerciser to the desired position, and then lower it.
until they begin to move with a continuous motion.
Note: The crank arms can turn in either direction.
It is recommended that you turn the crank arms in
the direction shown by the arrow below; however,
for variety you can turn the crank arms in the
opposite direction.
Handgrip
Pulse
Sensors
Upper Body Arms
Place
your foot
here
Pedals
Crank Arm
To dismount the elliptical exerciser, wait until the ped-
als come to a complete stop. Note: The elliptical
exerciser does not have a free wheel; the pedals
will continue to move until the flywheel stops.
When the pedals are stationary, step off the higher
pedal first. Then, step off the lower pedal.
12
Download from Www.Somanuals.com. All Manuals Search And Download.
CONSOLE DIAGRAM
FEATURES OF THE CONSOLE
The console also features the new iFIT Interactive
Workout System. The iFIT Interactive Workout System
enables the console to accept iFIT Cards containing
workout programs designed to help you achieve specif-
ic fitness goals. For example, lose unwanted pounds
with the 8-week Weight Loss program. iFIT programs
control the resistance of the pedals while the voice of a
personal trainer coaches you and motivates you
through your workouts. One iFIT Card with three new
programs is included. Additional iFIT Cards are avail-
able separately. To purchase iFIT Cards, go to
www.iFIT.com or call the toll-free telephone num-
ber on the front cover of this manual. iFIT Cards
are also available at select stores.
The advanced console offers an array of features
designed to make your workouts more effective and
enjoyable. When you select the manual mode of the
console, you can change the resistance of the pedals
and the incline of the ramp with the touch of a button.
As you exercise, the console will provide continuous
exercise feedback. You can even measure your heart
rate using the handgrip pulse sensor.
The console features twenty preset programs. Each
program automatically changes the resistance of the
pedals and prompts you to increase or decrease your
pedaling pace as it guides you through an effective
workout.
You can even connect your MP3 player or CD player
to the console’s stereo sound system and listen to
your favorite music or audio books while you exercise.
The console also offers two custom programs that
allow you to create your own workout programs and
store them in memory for future use.
To use the manual mode of the console, follow the
steps beginning on page 14. To use a preset
program, see page 16. To create a custom
program, see page 17. To use a custom program,
see page 18. To use a heart rate program,
see page 19. To use an iFIT program, see page 21.
To use the stereo sound system, see page 21.
In addition, the console features two heart rate pro-
grams that change the resistance of the pedals to
keep your heart rate near target heart rate settings
while you exercise.
13
Download from Www.Somanuals.com. All Manuals Search And Download.
Follow your progress with the display.
HOW TO USE THE MANUAL MODE
4
While you pedal, the upper left corner of the dis-
play will show the elapsed time. Note: During a
program, except for heart rate program 1, the dis-
play will show the time remaining in the program.
Note: If there is a sheet of clear plastic on the face of
the console, remove the plastic.
Press any button on the console or begin
1
pedaling to turn on the console.
When you turn on the console, the display will
light. A tone will then sound and the console will
be ready for use.
Select the manual mode.
2
When you turn on the console, the manual mode
will be selected. If you have selected a program,
reselect the manual mode by pressing any of the
Programs buttons repeatedly until zeros appear in
the display.
The upper right corner of the display will show the
distance you have pedaled, in total revolutions.
The display will also show your heart rate when
you use the handgrip pulse sensor (see step 5 on
page 15).
The lower left corner of the display will show the
ramp incline level.
The lower center of the display will show the
approximate number of calories you have burned.
The lower right corner of the display will show
your pedaling pace, in revolutions per minute.
Begin pedaling and change the resistance of
3
the pedals and the incline of the ramp as
The center of the display will show the resistance
level of the pedals for a few seconds each time the
resistance level changes.
desired.
As you pedal, change the resistance of the ped-
als by pressing the OneTouch Resistance but-
tons. There are fifteen resistance levels. Note:
After you press the buttons, it will take a moment
for the pedals to reach the selected resistance
level.
You can also view selected information at a larger
size. Press the Display button repeatedly to view
the elapsed time and the distance you have ped-
aled, the elapsed time and the approximate num-
ber of calories you have burned, or the elapsed
time. Press the Display button again to view a
workout history of resistance levels and pedaling
pace.
To vary the motion of the pedals, you can change
the incline of the ramp. To change the incline,
press the OneTouch Ramp buttons. There are
five incline levels. Note: After you press the but-
tons, it will take a moment for the ramp to reach
the selected incline level.
To again view the time, distance, ramp incline,
number of calories burned, and pedaling pace,
press the Display button again.
To view the total distance pedaled since the ellipti-
cal exerciser was purchased and the trip distance,
press the Odometer button. The information will
appear in the display for a few seconds. To reset
the trip distance, hold down the Odometer button
for a few seconds.
14
Download from Www.Somanuals.com. All Manuals Search And Download.
Measure your heart rate if desired.
Turn on the fan if desired.
5
6
7
If there are
To turn on the fan at high speed, press the Fan
button. To turn on the fan at low speed, press the
Fan button a second time. To turn off the fan,
press the Fan button again. Note: If the pedals
are not moved for about thirty seconds, the fan
will automatically turn off.
sheets of clear
plastic on the
metal contacts
on the handgrip
pulse sensor,
remove the plas-
tic. In addition,
make sure that
your hands are
clean. To mea-
sure your heart
Contacts
Pivot the fan louvers above the display upward or
downward to direct the airflow from the fan.
When you are finished exercising, the console
will turn off automatically.
rate, hold the handgrip pulse sensor with your
palms resting against the metal contacts. Avoid
moving your hands or gripping the contacts
tightly.
If the pedals are not moved for several seconds, a
series of tones will sound and the console will
pause.
When your pulse is detected, your heart rate will
be shown in the display. For the most accurate
heart rate reading, hold the contacts for at least 15
seconds.
If the pedals are not moved for about five min-
utes, the console will turn off and the display will
be reset.
If your heart rate is not shown, make sure that
your hands are positioned as described. Be care-
ful not to move your hands excessively or to
squeeze the metal contacts tightly. For optimal
performance, clean the metal contacts using a
soft cloth; never use alcohol, abrasives, or
chemicals to clean the contacts.
15
Download from Www.Somanuals.com. All Manuals Search And Download.
During the program, the program profile will show
your progress (see the drawing above). The
flashing segment of the profile represents the cur-
rent segment of the program. The height of the
flashing segment indicates the resistance level
for the current segment. At the end of each seg-
ment of the program, a series of tones will sound
and the next segment of the profile will begin to
flash. If a different resistance level is pro-
grammed for the next segment, the resistance
level will appear in the display for a few seconds
to alert you. The resistance of the pedals will then
change.
HOW TO USE A PRESET PROGRAM
Turn on the console.
1
See step 1 on page 14.
Select a preset program.
2
To select a weight loss program, press the
Weight Loss Programs button repeatedly; to
select an aerobic fitness program, press the
Aerobic Fitness Programs button; to select a
competition program, press the Competition
Programs button.
As you exercise, you
will be prompted to
keep your pedaling
When you select a preset program, the name of
the program, the program time, and the maximum
pace and resistance level for the program will
appear in the display for a few seconds. A profile
of the resistance levels of the program will then
appear in the display.
pace near the target
pace setting for the
current segment.
When an upward-pointing arrow or the prompt
SPEED UP appears next to the pace information
in the display (see step 4 on page 16), increase
your pace. When a downward-pointing arrow or
the prompt SLOW DOWN appears, decrease
your pace. When no arrow or prompt appears,
maintain your current pace. Important: The tar-
get pace settings are intended only to provide
motivation. Make sure to pedal at a pace that
is comfortable for you.
Profile
If the resistance level for the current segment is
too high or too low, you can manually override
the setting by pressing the OneTouch Resistance
buttons. However, when the current segment
ends, the pedals will automatically adjust to the
resistance level for the next segment.
Begin pedaling to start the program.
3
Each program is divided into 20, 30, or 45 one-
minute segments. One resistance level and one
target pace setting are programmed for each seg-
ment. Note: The same resistance level and/or tar-
get pace setting may be programmed for two or
more consecutive segments.
If you stop pedaling for several seconds, a series
of tones will sound and the program will pause. To
restart the program, simply resume pedaling. The
program will continue until the last segment of the
profile flashes and the last segment of the pro-
gram ends.
16
Download from Www.Somanuals.com. All Manuals Search And Download.
Follow your progress with the display.
HOW TO CREATE A CUSTOM PROGRAM
Turn on the console.
4
During the program, the display will show the pro-
gram profile, the time remaining in the program,
and the distance you have pedaled.
1
See step 1 on page 14.
To view the profile, your pedaling pace, and the
distance you have pedaled, press the Display but-
ton. Note: The words SPEED UP or SLOW
DOWN may appear in the display to prompt you
to keep your pedaling pace near the target pace
setting for the current segment.
Select a custom program.
2
To select a custom program, press the Custom
Programs button once or twice. When you select
a custom program, the name of the program and
the settings for the program will appear in the dis-
play for a few seconds.
To view the time remaining in the program and the
distance pedaled, press the Display button. Press
the Display button again to view the time remain-
ing and the approximate number of calories
burned.
To view the time remaining, distance pedaled,
ramp incline, number of calories burned, and ped-
aling pace, press the Display button again. Note:
An upward- or downward-pointing arrow may
appear in the display to prompt you to keep your
pedaling pace near the target pace setting for the
current segment.
Begin pedaling to start the program, and
program the desired settings.
3
To view the first display again, press the Display
button again.
Each custom program is divided into 30 one-
minute segments. You can program one resis-
tance level and one target pace setting for each
segment.
Measure your heart rate if desired.
See step 5 on page 15.
5
6
7
To program a resistance level for the first seg-
ment, simply adjust the resistance of the pedals
by pressing the OneTouch Resistance buttons. To
program a target pace for the first segment, sim-
ply pedal at the desired pace.
Turn on the fan if desired.
See step 6 on page 15.
When you are finished exercising, the console
will turn off automatically.
At the end of the first segment, the program will
store the current resistance level and your current
pace in memory. Program a resistance level and
a target pace for the second segment as
described above.
See step 7 on page 15.
Continue exercising for up to forty minutes. Stop
pedaling when you are finished with your work-
out. The program you created will then be stored
in memory. Note: If your workout is less than thirty
minutes long, any remaining segments in the pro-
gram will be stored with the last resistance level
and target pace setting you programmed.
When the program is finished, the console
will turn off automatically.
4
See step 7 on page 15.
17
Download from Www.Somanuals.com. All Manuals Search And Download.
As you exercise, you
HOW TO USE A CUSTOM PROGRAM
Turn on the console.
will be prompted to
keep your pedaling
pace near the target
1
pace setting for the
See step 1 on page 14.
current segment.
When an upward-pointing arrow or the prompt
SPEED UP appears next to the pace information
in the display (see step 4 on page 17), increase
your pace. When a downward-pointing arrow or
the prompt SLOW DOWN appears, decrease
your pace. When no arrow or prompt appears,
maintain your current pace. Important: The tar-
get pace settings are intended only to provide
motivation. Make sure to pedal at a pace that
is comfortable for you.
Select a custom program.
2
To select a custom program, press the Custom
Programs button repeatedly until the words CUS-
TOM 1 or CUSTOM 2 appear in the display.
When you select a custom program, the name of
the program, the program time, and the maximum
pace and resistance level will appear in the dis-
play for a few seconds. A profile of the resistance
levels of the program will then appear in the dis-
play.
If the resistance level for the current segment is
too high or too low, you can manually override
the setting by pressing the OneTouch Resistance
buttons. However, when the current segment
ends, the pedals will automatically adjust to the
resistance level for the next segment.
Profile
If you stop pedaling for several seconds, a series
of tones will sound and the program will pause. To
restart the program, simply resume pedaling. The
program will continue until the last segment of the
profile flashes and the last segment of the pro-
gram ends.
Begin pedaling to start the program.
3
Change the program if desired.
4
Each custom program is divided into 30 one-
minute segments. One resistance level and one
target pace setting are programmed for each seg-
ment. Note: The same resistance level and/or tar-
get pace setting may be programmed for two or
more consecutive segments.
If desired, you can change the program while
using it. To change the resistance level for the
current segment, simply press the OneTouch
Resistance buttons. At the end of the current seg-
ment, the new resistance level will be stored in
memory. To change the target pace for the cur-
rent segment, simply change your pedaling
pace. At the end of the current segment, your
pace will be stored in memory. You can continue
exercising and changing the program for up to
thirty minutes.
During the program, the program profile will show
your progress. The flashing segment of the profile
represents the current segment of the program.
The height of the flashing segment indicates the
resistance level for the current segment. At the
end of each segment of the program, a series of
tones will sound and the next segment of the pro-
file will begin to flash. If a different resistance
level is programmed for the next segment, the
resistance level will appear in the display for a
few seconds to alert you. The resistance of the
pedals will then change.
18
Download from Www.Somanuals.com. All Manuals Search And Download.
Follow your progress with the display.
See step 4 on page 17.
HOW TO USE A HEART RATE PROGRAM
5
6
7
8
Turn on the console.
1
Measure your heart rate if desired.
See step 5 on page 15.
See step 1 on page 14.
Select a heart rate program.
2
Turn on the fan if desired.
See step 6 on page 15.
To select one of the heart rate programs, press
the Heart Rate Programs button repeatedly until
the words HEART RATE 1 or HEART RATE 2
appear in the display.
When you are finished exercising, the console
will turn off automatically.
Enter a target heart rate setting.
3
See step 7 on page 15.
A few seconds after you select a heart rate pro-
gram, the words ENTER MAX TARGET HEART
RATE FOR THIS WORKOUT will appear in the
display and the number 110 will begin to flash.
During heart rate program 1, the same target
heart rate setting will be programmed for all seg-
ments of the program. If you have selected heart
rate program 1, press the increase and decrease
buttons above the Heart Rate Programs button to
enter the desired target heart rate setting (see
EXERCISE INTENSITY on page 23).
During heart rate program 2, different target
heart rate settings will be programmed for differ-
ent segments of the program. If you have select-
ed heart rate program 2, press the increase and
decrease buttons above the Heart Rate
Programs button to enter the desired maximum
target heart rate setting for the program (see
EXERCISE INTENSITY on page 23).
Hold the handgrip pulse sensor.
4
It is not necessary to hold the handgrip pulse
sensor continuously during heart rate programs;
however, you should hold the handgrip pulse sen-
sor frequently for the programs to operate proper-
ly. Each time you hold the handgrip pulse sen-
sor, keep your hands on the metal contacts
for at least 30 seconds.
19
Download from Www.Somanuals.com. All Manuals Search And Download.
If the resistance level for the current segment is
too high or too low, you can manually override
the setting by pressing the OneTouch Resistance
buttons. However, when the console compares
your heart rate to the target heart rate setting, the
resistance of the pedals may automatically
increase or decrease to bring your heart rate
closer to the target heart rate setting.
Begin pedaling to start the program.
5
Heart rate program 1 is divided into 40 one-
minute segments. Note: For a shorter workout,
stop exercising or select a different program
before the program ends.
Heart rate program 2 is divided into 30 one-
minute segments. One target heart rate setting is
programmed for each segment. Note: The same
target heart rate setting may be programmed for
consecutive segments.
If you stop pedaling for several seconds, a series
of tones will sound and the program will pause. To
restart the program, simply resume pedaling. The
program will continue until the last segment of the
program ends.
During the program, the program profile in the
display will show your progress. The flashing seg-
ment of the profile represents the current seg-
ment of the program. The height of the flashing
segment indicates the target heart rate setting for
the current segment. At the end of each segment
of the program, a series of tones will sound and
the next segment of the profile will begin to flash.
Follow your progress with the display.
6
During heart rate program 1, the display will
show a graphic that represents a heartbeat each
time your heartbeat is detected, the elapsed time,
and the distance that you have pedaled. During
heart rate program 2, the display will show the
program profile, the time remaining in the pro-
gram, and the distance that you have pedaled.
Profile
To view the profile, your pedaling pace, and the
distance you have pedaled, press the Display but-
ton. Note: The words SPEED UP or SLOW
DOWN may appear in the display to prompt you
to keep your pedaling pace near the target pace
setting for the current segment.
During both programs, the console will regularly
compare your heart rate to the target heart rate
setting for the current segment of the program. If
your heart rate is too far below or above the tar-
get heart rate setting, the resistance of the pedals
will automatically increase or decrease to bring
your heart rate closer to the target heart rate set-
ting. Each time the resistance changes, the resis-
tance level will appear in the display for a few
seconds to alert you.
To view the time remaining in the program and the
distance pedaled, press the Display button. Press
the Display button again to view the time remain-
ing and the approximate number of calories
burned.
To view the time remaining, distance pedaled,
ramp incline, number of calories burned, and ped-
aling pace, press the Display button again. Note:
An upward- or downward-pointing arrow may
appear in the display to prompt you to keep your
pedaling pace near the target pace setting for the
current segment.
While you exercise,
you will be prompted
to maintain a con-
stant pedaling pace.
To view the first display again, press the Display
button again.
When an upward-
pointing arrow or the
prompt SPEED UP appears next to the pace
information in the display (see step 6 on this
page), increase your pace. When a downward-
pointing arrow or the prompt SLOW DOWN
appears, decrease your pace. When no arrow or
prompt appears, maintain your current pace.
Turn on the fan if desired.
7
8
See step 6 on page 15.
When you are finished exercising, the console
will turn off automatically.
See step 7 on page 15.
20
Download from Www.Somanuals.com. All Manuals Search And Download.
HOW TO USE AN IFIT PROGRAM
HOW TO USE THE STEREO SOUND SYSTEM
To play music or audio
books through the con-
sole’s stereo sound system
Turn on the console.
1
See step 1 on page 14.
Cable
while you exercise, first
locate the stereo audio
Insert an iFIT Card and select a program.
2
cable in the center of the
console above the speak-
To use an iFIT program, insert an iFIT Card into
the iFIT slot; make sure that the iFIT Card is ori-
ented so the metal contacts are face-down and
are facing the slot. When the iFIT Card is proper-
ly inserted, the indicator next to the slot will light
and the words IFIT 1 will appear in the display.
ers. Plug the cable into a jack on your MP3 player or
CD player; make sure that the audio cable is fully
plugged in.
Next, press the play button on your MP3 player or CD
player. Adjust the volume of the speakers using the
volume control on your MP3 player or CD player.
When not in use, insert the stereo audio cable into the
storage recess on the console.
iFIT Slot
iFIT Card
Next, select the desired program on the iFIT Card
by pressing the increase and decrease buttons
next to the iFIT slot.
A moment after you select a program, the voice
of a personal trainer will begin guiding you
through your workout. iFIT programs work in the
same way as preset programs. To use the pro-
gram, see steps 3 to 6 on pages 16 and 17.
21
Download from Www.Somanuals.com. All Manuals Search And Download.
MAINTENANCE AND TROUBLESHOOTING
Inspect and tighten all parts of the elliptical exerciser
regularly. Replace any worn parts immediately.
HOW TO ELIMINATE FLEXING IN THE CENTER OF
THE ELLIPTICAL EXERCISER
To clean the elliptical exerciser, use a damp cloth and
a small amount of mild soap. Important: To avoid
damage to the console, keep liquids away from
the console and keep the console out of direct
sunlight.
If the elliptical exerciser flexes in the center during
use, turn the center foot beneath the frame (see the
drawing at the left) until the flexing is eliminated.
HOW TO ADJUST THE BELT
HOW TO LEVEL THE ELLIPTICAL EXERCISER
If the pedals slip
while you are
If the elliptical
pedaling, even
while the resis-
tance is adjusted
to the highest
exerciser rocks
on your floor dur-
ing use, turn one
or both of the
setting, the belt
may need to be
leveling feet
Center
beneath the rear
Foot
adjusted. To
13
stabilizer until
adjust the belt,
first carefully pry
off the left Disc
12
the rocking
Leveling
Feet
motion is elimi-
nated.
Cover (13) using a flat screwdriver. Next, remove the
four screws (not shown) from the center of the left
Disc (12). Gently rotate the Disc Cover and the Disc
away from the elliptical exerciser.
HANDGRIP PULSE SENSOR TROUBLESHOOTING
• Avoid moving your hands while using the handgrip
pulse sensor. Excessive movement may interfere
with heart rate readings.
Loosen, but do
not remove, the
three 1/4" x
19mm Button
Screws (114).
Insert the shaft of
• Do not hold the metal contacts too tightly; doing so
may interfere with heart rate readings.
47
a screwdriver
• For the most accurate heart rate reading, hold the
metal contacts for about 30 seconds.
48
downward
96
114
between the
Idler (47) and the
Idler Pulley (48).
Pull the top of the
screwdriver
• For optimal performance of the handgrip pulse sen-
sor, keep the metal contacts clean. The contacts
can be cleaned with a soft cloth—never use alco-
hol, abrasives, or chemicals to clean the con-
tacts.
toward the rear of the elliptical exerciser until the Belt
(96) is tight, and then tighten the three Button Screws.
Reattach the left disc with the four screws and then
reattach the left disc cover.
22
Download from Www.Somanuals.com. All Manuals Search And Download.
CONDITIONING GUIDELINES
During the first few minutes of exercise, your body
uses easily accessible carbohydrate calories for ener-
gy. Only after the first few minutes of exercise does
your body begin to use stored fat calories for energy.
If your goal is to burn fat, adjust the intensity of your
exercise until your heart rate is near the lowest num-
ber in your training zone as you exercise.
WARNING:
Before beginning this or any exercise pro-
gram, consult your physician. This is espe-
cially important for persons over the age of 35
or persons with pre-existing health problems.
The pulse sensor is not a medical device.
Various factors may affect the accuracy of
heart rate readings. The pulse sensor is
intended only as an exercise aid in determin-
ing heart rate trends in general.
For maximum fat burning, adjust the intensity of your
exercise until your heart rate is near the middle num-
ber in your training zone as you exercise.
Aerobic Exercise
If your goal is to strengthen your cardiovascular sys-
tem, your exercise must be “aerobic.” Aerobic exer-
cise is activity that requires large amounts of oxygen
for prolonged periods of time. This increases the
demand on the heart to pump blood to the muscles,
and on the lungs to oxygenate the blood. For aerobic
exercise, adjust the intensity of your exercise until
your heart rate is near the highest number in your
training zone as you exercise.
The following guidelines will help you to plan your
exercise program. Remember that proper nutrition
and adequate rest are essential for successful results.
EXERCISE INTENSITY
Whether your goal is to burn fat or to strengthen your
cardiovascular system, the key to achieving the
desired results is to exercise with the proper intensity.
The proper intensity level can be found by using your
heart rate as a guide. The chart below shows recom-
mended heart rates for fat burning, maximum fat
burning, and cardiovascular (aerobic) exercise.
WORKOUT GUIDELINES
Each workout should include the following three parts:
A warm-up, consisting of 5 to 10 minutes of stretching
and light exercise. A proper warm-up increases your
body temperature, heart rate, and circulation in prepa-
ration for exercise.
Training zone exercise, consisting of 20 to 30 min-
utes of exercising with your heart rate in your training
zone. Note: During the first few weeks of your exer-
cise program, do not keep your heart rate in your
training zone for longer than 20 minutes.
To find the proper heart rate for you, first find your age
at the bottom of the chart (ages are rounded off to the
nearest ten years). Next, find the three numbers above
your age. The three numbers are your “training zone.”
The lower two numbers are recommended heart rates
for fat burning; the highest number is the recommend-
ed heart rate for aerobic exercise.
A cool-down, with 5 to 10 minutes of stretching. This
will increase the flexibility of your muscles and will
help to prevent post-exercise problems.
EXERCISE FREQUENCY
To maintain or improve your condition, complete three
workouts each week, with at least one day of rest
between workouts. After a few months of regular exer-
cise, you may complete up to five workouts each week
if desired. The key to success is to make exercise a
regular and enjoyable part of your everyday life.
Fat Burning
To burn fat effectively, you must exercise at a relative-
ly low intensity level for a sustained period of time.
23
Download from Www.Somanuals.com. All Manuals Search And Download.
PART LIST—MODEL NO. RBEL9906.0
R1206A
Key No. Qty.
Description
Key No. Qty.
Description
1
1
1
1
1
1
1
1
2
1
1
1
2
2
1
1
2
2
2
1
1
2
1
1
2
2
1
1
1
1
1
1
1
1
1
1
1
1
4
2
1
2
4
6
1
1
1
1
1
1
1
Frame
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
85
86
87
88
89
90
91
92
93
94
95
96
97
98
99
100
1
2
2
2
2
1
1
2
2
1
1
2
1
1
1
6
8
4
1
1
1
1
1
4
1
2
2
1
4
1
1
4
2
2
2
2
5
5
4
1
1
1
2
3
1
1
1
2
4
4
Clamp
2
Folding Frame
Rear Stabilizer
Front Stabilizer
Ramp
Large Axle Cover
Crank Bushing
Crank Bushing Sleeve
Crank Arm
3
4
5
6
Front Ramp Cover
Rear Ramp Cover
Side Ramp Cover
Lift Motor
Crank Arm Spacer
Large Pulley
7
8
Crank Flange
Crank Bearing Assembly
Crank Spacer
Crank
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
Upright
Console
Disc
Lift Bracket
Disc Cover
Lift Axle
Left Side Shield
Right Side Shield
Rear Endcap
Lower Wire Harness
Upper Wire Harness
Axle Cover
Wheel
Bushing Assembly
Brass Bushing
Latch Bracket
Pivot Bracket
Upper Body Axle
Ramp Axle
Wheel Cover
Rear Upright Cover
Front Upright Cover
Handgrip
Left Upper Body Arm
Right Upper Body Arm
Upper Body Leg
Pulse Sensor/Wire
Left Rear Upper Body Cover
Left Front Upper Body Cover
Right Rear Upper Body Cover
Right Front Upper Body Cover
Left Link Arm
Pivot Axle
Link Arm Spacer
Base Pin
Latch Spacer
Hairpin Cotter Spacer
Pivot Pin
Hairpin Cotter
E-clip
Right Link Arm
Left Pedal Arm
Right Pedal Arm
Left Pedal
Roll Pin
M10 x 93mm Button Screw
Crank Snap Ring
Crank Arm Washer
Outside Crank Bushing
Flange Screw
M10 x 25mm Washer
Bolt Set
Right Pedal
Left Frame Cover
Right Frame Cover
Roller
Pedal Arm Endcap
Tray
Small Snap Ring
Idler Snap Ring
Eddy Snap Ring
Idler Spacer
Pedal Arm Latch
Pedal Arm Latch Spring
Pedal Arm Cap
Eddy Mechanism
Eddy Crank Assembly
Pillow Block
M10 Nylon Locknut
Idler Washer
Center Foot
Belt
Idler
Latch Button
Idler Pulley
Leveling Foot
M10 Curved Washer
Wave Washer
Eddy Motor
Reed Switch/Wire
24
Download from Www.Somanuals.com. All Manuals Search And Download.
Key No. Qty.
Description
Key No. Qty.
Description
101
102
103
104
105
106
107
108
109
110
111
112
113
114
115
116
117
118
119
120
4
12
8
M8 Split Washer
121
122
123
124
125
126
127
128
129
130
131
132
133
134
135
136
#
1
1
2
1
1
1
1
1
1
1
2
4
2
2
1
1
-
Left Lift Arm
M6 Split Washer
Right Lift Arm
Lift Bushing
M8.5 x 16mm x 1.5mm Washer
M8 x 20mm x 2mm Washer
M8 x 16mm Button Screw
M8 x 15mm Button Screw
M8 x 20mm Button Screw
M6 x 62mm Screw
2
Transformer
2
Control Box Cover
Motor Clevis Pin
Bracket Pin
10
8
4
Lift Reed Switch
Switch Cover
Power Socket
Motor Spacer
M4 x 10mm Screw
Lift Axle Washer
Lift Axle Screw
Control Box
4
M6 x 35mm Screw
6
M8 x 25mm Button Screw
M10 x 20mm Button Screw
M8 x 25mm Shoulder Screw
M8 x 30mm Button Screw
1/4" x 19mm Button Screw
M4 x 12mm Screw
4
8
2
5
3
54
8
M4 x 16mm Screw
Control Board
User’s Manual
Hex Key
M4 x 16mm Cupped Screw
M6 Nylon Locknut
4
#
-
4
Bearing Assembly
#
-
Grease
2
Upright Brass Bushing
#
-
Power Cord
Note: “#” indicates a non-illustrated part. Specifications are subject to change without notice. See the back cover
of this manual for information about ordering replacement parts.
25
Download from Www.Somanuals.com. All Manuals Search And Download.
EXPLODED DRAWING A—MODEL NO. RBEL9906.0
R1206A
25
11
23
21
25
116
116
116
106
116
117
20
29
105
115
119
100
120
104
21
40
28
119
100
116
116
22
71
120
10
27
116
24
67
119
19
105
104
110
103
66
74
117
65
67
26
66
119
106
66
106
31
116
106
74
103
35
103
67
100
24
67
34
43
106
66
39
89
43
89
38
103
67
67
33
74
67
38
103
110
43
39
42
41
102
102
108
30
66
43
108
43
117
116
116
109
100
37
106
43
102
67
32
117
116
66
103
36
102
109
109
117
42
41
108
117
117
116
117
26
Download from Www.Somanuals.com. All Manuals Search And Download.
EXPLODED DRAWING B—MODEL NO. RBEL9906.0
R1206A
17
18
4
93
82
6
99
12
116
13
88
116
17
107
116
8
93
5
101
101
131
18
7
8
9
107
107
116
111
129
128
126
116
87
50
62
116
79
88
116
68
49
118
116
1
72
122
63
38
51
118
116
113
103
133
134
89
38
79
127
68
102
45
15
102
68
114
91
114
87
123
121
111
68
53
123
95
84
52
85
46
44
47
92
54
133
48
134
112
90
55
58
88
86
116
125
94
132
83
88
114
64
59
61
124
116
111
2
87
59
132
14
87
116
60
115
136
73
135
130
110
111
116
57
12
83
110
16
58
98
116
86
56
78
77
99
82
3
70
79
55
112
98
87
80
75
69
76
13
103
113
16
84
53
77
79
54
96
76
81
85
52
97
27
Download from Www.Somanuals.com. All Manuals Search And Download.
HOW TO ORDER REPLACEMENT PARTS
To order replacement parts, please see the front cover of this manual. To help us assist you, be prepared to
provide the following information when contacting us:
• the MODEL NUMBER of the product (RBEL9906.0)
• the NAME of the product (REEBOK 1000 ZX elliptical exerciser)
• the SERIAL NUMBER of the product (see the front cover of this manual)
• the KEY NUMBER and DESCRIPTION of the part(s) (see pages 24 to 27)
LIMITED WARRANTY
ICON Health & Fitness, Inc. (ICON) warrants this product to be free from defects in workmanship and mate-
rial, under normal use and service conditions, for a period of one (1) year from the date of purchase. There
is a lifetime warranty on the frame. This warranty extends only to the original purchaser. ICON's obligation
under this warranty is limited to replacing or repairing, at ICON's option, the product through one of its autho-
rized service centers. All repairs for which warranty claims are made must be pre-authorized by ICON. If the
product is shipped to a service center, freight charges to and from the service center will be the customer’s
responsibility. For in-home service, the customer will be responsible for a minimal trip charge. This warran-
ty does not extend to any product or damage to a product caused by or attributable to freight damage,
abuse, misuse, improper or abnormal usage or repairs not provided by an ICON authorized service center;
products used for commercial or rental purposes; or products used as store display models. No other war-
ranty beyond that specifically set forth above is authorized by ICON.
ICON is not responsible or liable for indirect, special or consequential damages arising out of or in connec-
tion with the use or performance of the product or damages with respect to any economic loss, loss of prop-
erty, loss of revenues or profits, loss of enjoyment or use, costs of removal or installation or other conse-
quential damages of whatsoever nature. Some states do not allow the exclusion or limitation of incidental
or consequential damages. Accordingly, the above limitation may not apply to you.
The warranty extended hereunder is in lieu of any and all other warranties and any implied warranties of
merchantability or fitness for a particular purpose is limited in its scope and duration to the terms set forth
herein. Some states do not allow limitations on how long an implied warranty lasts. Accordingly, the above
limitation may not apply to you.
This warranty gives you specific legal rights. You may also have other rights which vary from state to state.
ICON HEALTH & FITNESS, INC., 1500 S. 1000 W., LOGAN, UT 84321-9813
Part No. 247875 R1206A
Printed in China © 2006 ICON IP, Inc.
Download from Www.Somanuals.com. All Manuals Search And Download.
|