Model No. RBBE0955.0
Serial No.
Write the serial number in the
space above for future reference.
Serial Number Decal (Under Seat)
USER’S MANUAL
QUESTIONS?
As a manufacturer, we are com-
mitted to providing complete
customer satisfaction. If you
have questions, or if a part is
damaged or missing, PLEASE
CONTACT OUR CUSTOMER
SERVICE DEPARTMENT
DIRECTLY.
CALL TOLL-FREE:
1-877-994-4999
Mon.–Fri., 6 a.m.–6 p.m. MST
ON THE WEB:
CAUTION
Visit our website at
Read all precautions and instruc-
tions in this manual before using
this equipment. Save this manual
for future reference.
new products, prizes,
fitness tips, and much more!
Download from Www.Somanuals.com. All Manuals Search And Download.
IMPORTANT PRECAUTIONS
WARNING:
To reduce the risk of serious injury, read the following important precautions
before using the weight bench.
1. Read all instructions in this manual and all
warnings on the weight bench before using
the weight bench. Use the weight bench only
as described in this manual.
11. The weight bench is designed to support a
maximum user weight of 300 pounds, and a
maximum total weight of 410 pounds. Do not
place more than 110 pounds, including the
barbell, on the weight rests. Do not place
more than 50 pounds on the leg lever. Do not
place more than 80 pounds on the weight
carriage. Do not place more than 30 pounds
on either butterfly arm.
2. It is the responsibility of the owner to ensure
that all users of the weight bench are ade-
quately informed of all precautions.
3. The weight bench is intended for home use
only. Do not use the weight bench in any
commercial, rental, or institutional setting.
12. Always make sure there is an equal amount
of weight on each side of the barbell when
you are using it. When adding or removing
weights, always keep some weight on both
ends of the barbell to prevent the barbell
from tipping.
4. Keep the weight bench indoors, away from
moisture and dust. Place the weight bench
on a level surface, with a mat beneath it to
protect the floor or carpet. Make sure that
there is enough clearance around the weight
bench to mount, dismount, and use the
weight bench.
13. Always place an equal amount of weight on
each side of the weight carriage or on each
butterfly arm.
5. Inspect and properly tighten all parts regular- 14. Always secure the weights with the weight
ly. Replace any worn parts immediately.
clips when they are mounted on the weight
carriage.
6. Keep children under 12 and pets away from
the weight bench at all times.
15. When you are using the leg lever, place the
barbell with the same amount of weight on
the weight rests to balance the bench.
7. Keep hands and feet away from moving parts.
8. Always wear athletic shoes for foot protec-
tion while exercising.
16. Always exercise with a partner. Your partner
should be ready to catch the barbell if you
cannot complete a repetition.
9. Make sure that the cable remains on the pul-
ley at all times. If the cable binds as you are
exercising, stop immediately and make sure
that the cable is on the pulley. Replace the
cable at least every two years.
17. Always disconnect the lat bar from the cable
when performing an exercise that does not
require it.
18. If you feel pain or dizziness at any time while
exercising, stop immediately and begin cool-
ing down.
10. When using the backrest in a level or an
inclined position, make sure that the support
rod is inserted completely through the
uprights and turned to the locked position.
WARNING:
Before beginning this or any exercise program, consult your physician. This
is especially important for persons over the age of 35 or persons with pre-existing health problems.
Read all instructions before using. ICON assumes no responsibility for personal injury or property
damage sustained by or through the use of this product.
3
Download from Www.Somanuals.com. All Manuals Search And Download.
BEFORE YOU BEGIN
Thank you for selecting the versatile REEBOK® RS 100 model number and serial number before calling. The
weight bench. The weight bench offers a selection of
weight stations designed to develop every major mus-
cle group of the body. Whether your goal is to tone
your body, build dramatic muscle size and strength, or
improve your cardiovascular system, the weight bench
will help you to achieve the specific results you want.
model number is RBBE0955.0. The serial number can
be found on a decal attached to the weight bench (see
the front cover of this manual).
To avoid a registration fee for any service needed
under warranty, you must register the weight
For your benefit, read this manual carefully before
using the weight bench. If you have questions after
reading this manual, see the front cover of this manu-
al. To help us assist you, please note the product
Before reading further, please review the drawing
below and familiarize yourself with the parts that are
labeled.
Lat Bar
ASSEMBLED DIMENSIONS:
Height: 76 in. / 193 cm
Width: 67 in. / 170 cm
Depth: 66 in. / 168 cm
Lat Tower
Right Side
Weight Rest
Barbell
Adjustment Bar
Curl Pad
Backrest
Weight Carriage
Butterfly Arm
Leg Lever
Left Side
Seat
Note: The terms “right side” and “left side” are determined
relative to a person sitting on the bench; they do not corre-
spond to right and left on the drawings in the manual.
4
Download from Www.Somanuals.com. All Manuals Search And Download.
ASSEMBLY
• As you assemble the weight bench, make sure all
parts are oriented as shown in the drawings.
Make Things Easier for Yourself
Everything in this manual is designed to ensure
that the weight bench can be assembled suc-
cessfully by anyone. Most people find that by
setting aside plenty of time, assembly will go
smoothly.
• For help identifying small parts, use the PART
IDENTIFICATION CHART.
The included grease, and the following tools
(not included) may be required for assembly:
To hire an authorized service technician to
assemble the weight bench, call toll-free
1-800-445-2480.
• Two adjustable wrenches
• One hammer
• One standard screwdriver
Before beginning assembly, carefully read the
following information and instructions:
• One Phillips screwdriver
• Assembly requires two people.
• Clear tape or masking tape, and soapy water.
• Place all parts in a cleared area and remove the
packing materials. Do not dispose of the packing
materials until assembly is completed.
Assembly will be more convenient if you have a
socket set, a set of open-end or closed-end
wrenches, or a set of ratchet wrenches.
• Tighten all parts as you assemble them, unless
instructed to do otherwise.
1.
1
Before beginning assembly, make sure you
understand the information in the box
above. For help identifying small parts, use
the PART IDENTIFICATION CHART.
4
Attach an Upright (4) to the Crossbar (3) with two
M8 x 65mm Bolts (48), two M8 Washers (32), and
two M8 Nylon Locknuts (17). Make sure the
warning decal is in the indicated position. Do
not tighten the Locknuts.
4
3
48
Repeat this step with the other Upright (4).
32
Warning
48
Decal
17
5
Download from Www.Somanuals.com. All Manuals Search And Download.
2. Orient the Stabilizer (57) so that the indents
around the holes are on the bottom. Attach the
Bench Leg (2) to the Stabilizer with two M8 x
50mm Carriage Bolts (53) and two M8 Nylon
Locknuts (17). Do not tighten the Locknuts.
2
2
17
17
57
Indents
53
3. Attach the Bench Frame (1) to the Bench Leg (2)
with two M8 x 39mm Bolts (52), two M8 Washers
(32), and two M8 Nylon Locknuts (17). Make
sure that the bolt heads fit inside the hexago-
nal holes in the Bench Frame. Do not tighten
the Locknuts.
3
52
1
32
17
32
2
4. Attach the Bench Frame (1) to the Crossbar (3)
with an M8 x 54mm Bolt (43) and an M8 Nylon
Locknut (17); and with two M8 x 52mm Bolts (18),
two M8 Washers (32), and two M8 Nylon
4
17
32
Locknuts (17). Do not tighten the Locknuts.
43
1
3
17
18
5. Lubricate an M10 x 65mm Bolt (44) with grease.
Attach the Leg Lever (5) to the Bench Leg (2)
with the Bolt and an M10 Nylon Locknut (51). Do
not overtighten the Locknut; the Leg Lever
must be able to pivot easily.
5
51
5
44
Grease
2
6
Download from Www.Somanuals.com. All Manuals Search And Download.
6. Attach the Backrest Tubes (12) to the Backrest
(20) with four M6 x 38mm Screws (42) and four
M6 Washers (49). Do not tighten the Screws.
6
20
49
12
12
49
42
49
42
4
7. Slide the Adjustment Bar (13) into the Uprights (4)
from the side shown. Turn the Adjustment Bar so
that the locking pin wraps around the Upright.
7
20
Grease an M10 x 138mm Bolt (45). Attach the
Backrest Tubes (12) to the Bench Frame (1) with
the Bolt, two M10 Washers (50), and an M10
Nylon Locknut (51). Do not overtighten the
Locknut; the Backrest Tubes must be able to
pivot easily.
Locking
Pin
51
50
4
12
13
50
45
Tighten the M8 Nylon Locknuts (17) used in
steps 1–4. Tighten the four M6 x 38mm
Screws (42) used in steps 6.
1
8. Orient the Seat (21) as shown and attach it to the
Bench Frame (1) with four M6 x 15mm Screws
(41).
8
21
Wide
End
1
41
41
9. Insert a Pad Tube (19) into a hole in the Leg
Lever (5). Slide two Foam Pads (23) onto the Pad
Tube.
9
5
23
Repeat this step with the other Pad Tube (19).
19
23
19
7
Download from Www.Somanuals.com. All Manuals Search And Download.
10. Identify the Left Butterfly Arm (6) by the posi-
tion of the long side of the indicated tube.
Slide a Weight Stop (31) onto the Butterfly Arm.
10
11
12
6
Grease an M10 x 57mm Bolt (26). Attach the Left
Butterfly Handle (7) to the Left Butterfly Arm (6)
with the Bolt and an M10 Nylon Locknut (51). Do
not overtighten the Locknut; the Handle must
be able to pivot easily.
7
Tube
26
Repeat this step with the Right Butterfly Arm
(not shown) and Right Butterfly Handle (not
shown).
51
31
11. Grease an M10 x 138mm Bolt (45). Attach the
Left Butterfly Arm (6) to the indicated Upright (4)
with the Bolt and a Butterfly Knob (55).
56
4
45
Repeat this step with the Right Butterfly Arm
(56).
Grease
55
12. Route the Cable (34) through the Lat Tower (9)
and over the Pulley (36). Make sure that the
Cable is under the lat rest bar. Attach the
Pulley inside the Lat Tower with an M10 x 57mm
Bolt (26), two M10 Washers (50), two 7.5mm
Spacers (35), and an M10 Nylon Locknut (51).
34
35
35
36
51
50
26
50
Lat
Rest
9
13. Insert an M10 x 20mm Bolt (47) into the bracket
on the Weight Carriage (10).
13
9
34
51
Slide the Weight Carriage (10) onto the Lat Tower
(9). Make sure the bracket on the Weight
Carriage and the lat rest on the Lat Tower (see
step 12) are on the opposite sides.
47
10
Attach the Cable (34) to the M10 x 20mm Bolt
(47) with an M10 Nylon Locknut (51).
Bracket
8
Download from Www.Somanuals.com. All Manuals Search And Download.
14. Attach the Curl Pad (22) to the Curl Post (11) with
two M6 x 15mm Screws (41).
14
41
22
11
15. Insert the Inner Barbell (60) into the Outer Barbell
(59) and align the holes. Using a hammer, tap the
two Roll Pins (58) into the holes until they are
flush with the Outer Barbell.
15
58
59
60
16. Make sure that all parts are properly tightened before the weight bench is used. The use of all
remaining parts will be explained in ADJUSTMENTS starting on the next page.
9
Download from Www.Somanuals.com. All Manuals Search And Download.
ADJUSTMENTS
This section explains how to adjust the weight bench. See the EXERCISE GUIDELINES on page 13 for impor-
tant information about how to get the most benefit from your exercise program. Also, refer to the accompanying
exercise guide to see the correct form for each exercise.
Make sure all parts are properly tightened each time the weight bench is used. Replace any worn parts immediate-
ly. The weight bench can be cleaned with a damp cloth and a mild, non-abrasive detergent. Do not use solvents.
ADJUSTING THE BACKREST
4
The Backrest (20) can be used in a declined position, a
level position and two inclined positions. To use the
Backrest in a declined position, remove the Adjustment
Bar (13) and lay the Backrest on the Crossbar (3).
4
20
13
Locking
Pin
To use the Backrest (20) in a level or inclined posi-
tion, insert the Adjustment Bar (13) through a set of
holes in the Uprights (4). Rotate the Adjustment Bar
to the locked position, so the locking pin is wrapped
around the Upright. Lay the Backrest on the
Adjustment Bar.
3
ATTACHING THE CURL PAD OR LAT TOWER
For some exercises, the Curl Pad (22) needs to be
attached to the weight bench. To do this, remove the
38mm Square Cap (27) from the Bench Leg (2).
Insert the Curl Post (11) into the Front Leg and
secure it with the Curl Knob (38).
The Lat Tower (9) can be attached to the weight
bench in the same manner.
22
When the Curl Pad (22) and the Lat Tower (9) are
removed, the 38mm Square Cap (27) should be
inserted into the Bench Leg (2).
11
9
27
38
2
10
Download from Www.Somanuals.com. All Manuals Search And Download.
STORING THE CURL PAD
To store the Curl Pad (22), slide the Curl Post (11)
onto a storage tube on an Upright (4).
9
22
11
The Lat Tower (9) can be stored in the same way.
4
ATTACHING THE LAT BAR
34
To use the Lat Bar (14), attach it to the Cable (34)
with a Cable Clip (40).
40
14
WARNING:
Remove the Lat Bar
(14) when performing an exercise that does not
require it.
ATTACHING THE BUTTERFLY ARMS
56
To use the Butterfly Arms (6, 56), attach each Arm to
an Upright (4) with an M10 x 138mm Bolt (45) and a
Butterfly Knob (55).
4
18
Remove the Butterfly Arms (6, 56) when perform-
ing exercises that do not require them.
45
6
55
11
Download from Www.Somanuals.com. All Manuals Search And Download.
ATTACHING WEIGHTS
To use the Leg Lever (5), slide the desired Weights
(61 or 62) onto the weight tube on the Leg Lever. Do
not place more than 50 pounds on the Leg Lever.
56
10
WARNING:
When using the
Leg Lever (5), place the barbell with the
same amount of weight on the Upright (4)
weight rests to balance the bench.
5
61 or 62
33
To use the Weight Carriage (10), slide an equal
amount of Weight (61 or 62) onto each side of the
weight tube. Secure the Weights with the Weight
Clips (33). Do not place more than 80 pounds on
the Weight Carriage.
6
61 or 62
See the inset drawing. To use the Butterfly Arms (6,
56), first make sure there is a Weight Stop (not
shown) on each weight tube. Then slide the desired
Weights (61 or 62) onto the weight tubes. Do not
place more than 30 pounds on each Butterfly Arm.
61 or 62
ATTACHING WEIGHTS TO THE BARBELL
Slide an equal amount of Weight (61, 62) onto each
end of the barbell. Slide the two Lock Collars (63)
against the Weights, and tighten them fully.
Barbell
61
WARNING:
Always secure the
Weights (61, 62) on the barbell with the Lock
Collars (63). Never use the barbell with more
than 100 pounds.
62
63
12
Download from Www.Somanuals.com. All Manuals Search And Download.
EXERCISE GUIDELINES
THE FOUR BASIC TYPES OF WORKOUTS
PERSONALIZING YOUR EXERCISE PROGRAM
Muscle Building
To increase the size and strength of your muscles,
Determining the exact length of time for each workout,
as well as the number of repetitions or sets completed,
push them close to their maximum capacity. Your mus- is an individual matter. It is important to avoid overdo-
cles will adapt and grow as you progressively increase ing it during the first few months of your exercise pro-
the intensity of your exercise. You can adjust the inten- gram. You should progress at your own pace and be
sity level of an individual exercise in two ways:
• by changing the amount of weight used
• by changing the number of repetitions or sets per-
formed. (A “repetition” is one complete cycle of an
exercise, such as one sit-up. A “set” is a series of
repetitions.)
sensitive to your body’s signals. If you experience pain
or dizziness at any time while exercising, stop immedi-
ately and begin cooling down. Find out what is wrong
before continuing. Remember that adequate rest and a
proper diet are important factors in any exercise pro-
gram.
The proper amount of weight for each exercise
depends upon the individual user. You must gauge
WARMING UP
your limits and select the amount of weight that is right Begin each workout with 5 to 10 minutes of stretching
for you. Begin with 3 sets of 8 repetitions for each
exercise you perform. Rest for 3 minutes after each
set. When you can complete 3 sets of 12 repetitions
without difficulty, increase the amount of weight.
and light exercise to warm up. Warming up prepares
your body for more strenuous exercise by increasing
circulation, raising your body temperature and deliver-
ing more oxygen to your muscles.
Toning
WORKING OUT
You can tone your muscles by pushing them to a mod-
erate percentage of their capacity. Select a moderate
amount of weight and increase the number of repeti-
tions in each set. Complete as many sets of 15 to 20
repetitions as possible without discomfort. Rest for 1
minute after each set. Work your muscles by complet-
ing more sets rather than by using high amounts of
weight.
Each workout should include 6 to 10 different exercis-
es. Select exercises for every major muscle group,
emphasizing areas that you want to develop most. To
give balance and variety to your workouts, vary the
exercises from session to session.
Schedule your workouts for the time of day when your
energy level is the highest. Each workout should be
followed by at least one day of rest. Once you find the
schedule that is right for you, stick with it.
Weight Loss
To lose weight, use a low amount of weight and
increase the number of repetitions in each set.
Exercise for 20 to 30 minutes, resting for a maximum
of 30 seconds between sets.
EXERCISE FORM
Maintaining proper form is an essential part of an
effective exercise program. This requires moving
Cross Training
Cross training is an efficient way to get a complete and through the full range of motion for each exercise, and
well-balanced fitness program. An example of a bal-
anced program is:
• Plan strength training workouts on Monday,
Wednesday, and Friday.
• Plan 20 to 30 minutes of aerobic exercise, such as
running on a treadmill or riding on an exercise cycle
or an elliptical exerciser, on Tuesday and Thursday.
• Rest from both strength training and aerobic exercise
for at least one full day each week to give your body
time to regenerate.
moving only the appropriate parts of the body.
Exercising in an uncontrolled manner will leave you
feeling exhausted. On the exercise guide accompany-
ing this manual you will find photographs showing the
correct form for several exercises, and a list of the
muscles affected. Refer to the muscle chart on the
next page to find the names of the muscles.
The repetitions in each set should be performed
smoothly and without pausing. The exertion stage of
each repetition should last about half as long as the
The combination of strength training and aerobic exer- return stage. Proper breathing is important. Exhale
cise will reshape and strengthen your body, plus devel- during the exertion stage of each repetition and inhale
op your heart and lungs.
during the return stroke. Never hold your breath.
13
Download from Www.Somanuals.com. All Manuals Search And Download.
Rest for a short period of time after each set. The
ideal resting periods are:
• Rest for three minutes after each set for a muscle
building workout.
slowly as you stretch and do not bounce. Ease into
each stretch gradually and go only as far as you can
without strain. Stretching at the end of each workout
is an effective way to increase flexibility.
• Rest for one minute after each set for a toning work-
out.
STAYING MOTIVATED
• Rest for 30 seconds after each set for a weight loss
workout.
Plan to spend the first couple of weeks familiarizing
yourself with the equipment and learning the proper
form for each exercise.
For motivation, keep a record of each workout. The
chart on page 15 of this manual can be photocopied
and used to schedule and record your workouts. List
the date, the exercises performed, the resistance
used, and the numbers of sets and repetitions com-
pleted. Record your weight and key body measure-
ments at the end of every month. Remember, the key
to achieving the greatest results is to make exercise a
regular and enjoyable part of your everyday life.
COOLING DOWN
End each workout with 5 to 10 minutes of stretching.
Include stretches for both your arms and legs. Move
MUSCLE CHART
O
A. Sternomastoid (neck)
A
B. Pectoralis Major (chest)
C. Biceps (front of arm)
D. Obliques (waist)
P
L
Q
B
E. Brachioradials (forearm)
R
S
F. Hip Flexors (upper thigh)
G. Abductor (outer thigh)
H. Quadriceps (front of thigh)
I. Sartorius (front of thigh)
J. Tibialis Anterior (front of calf)
K. Soleus (front of calf)
L. Anterior Deltoid (shoulder)
M. Rectus Abdominus (stomach)
N. Adductor (inner thigh)
O. Trapezius (upper back)
P. Rhomboideus (upper back)
Q. Posterior Deltoid (shoulder)
R. Triceps (back of arm)
C
D
E
T
F
M
N
U
G
H
I
V
W
X
J
K
S. Latissimus Dorsi (mid back)
T. Spinae Erectors (lower back)
U. Gluteus Medius (hip)
V. Gluteus Maximus (buttocks)
W. Hamstring (back of leg)
X. Gastrocnemius (back of calf)
14
Download from Www.Somanuals.com. All Manuals Search And Download.
EXERCISE
WEIGHT
WEIGHT
WEIGHT
SETS
SETS
SETS
REPS
REPS
REPS
MONDAY
Date:
/
/
AEROBIC EXERCISE
EXERCISE
TUESDAY
Date:
/
/
WEDNESDAY
Date:
/
/
AEROBIC EXERCISE
EXERCISE
THURSDAY
Date:
/
/
FRIDAY
Date:
/
/
Make photocopies of this page for scheduling and recording your workouts.
15
Download from Www.Somanuals.com. All Manuals Search And Download.
PART IDENTIFICATION CHART
Refer to the drawings below to identify small parts used in assembly. The number in parentheses by each draw-
ing is the key number of the part, from the PART LIST in the center of this manual. Note: Some small parts
may have been pre-attached. If a part is not in the parts bag, check to see if it has been pre-attached.
M10 x 138mm Bolt (45)
M6 Washer (49)
M8 Washer (32)
M10 x 65mm Bolt (44)
M8 x 65mm Bolt (48)
M10 Washer (50)
M10 x 57mm Bolt (26)
M8 x 54mm Bolt (43)
M8 x 52mm Bolt (18)
M8 Nylon Locknut (17)
M10 Nylon Locknut (51)
M6 x 15mm Screw (41)
M8 x 50mm Carriage Bolt (53)
M8 x 39mm Bolt (52)
M10 x 20mm Bolt (47)
M6 x 38mm Screw (42)
Download from Www.Somanuals.com. All Manuals Search And Download.
PART LIST—Model No. RBBE0955.0
R0805A
Key No. Qty.
Description
Key No. Qty.
Description
1
2
3
4
5
6
7
8
1
1
1
2
1
1
1
1
1
1
1
2
1
1
4
2
11
2
2
1
1
1
4
6
4
3
6
9
6
4
2
8
2
Bench Frame
Bench Leg
Crossbar
Upright
Leg Lever
Left Butterfly Arm
Left Butterfly Handle
Right Butterfly Handle
Lat Tower
Weight Carriage
Curl Post
Backrest Tube
Adjustment Bar
Lat Bar
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
#
1
2
1
2
1
1
1
6
4
1
1
3
2
1
4
4
4
6
2
2
4
2
1
1
2
1
1
4
2
2
1
1
1
Cable
7.5mm Spacer
Pulley
Square Bushing
Curl Knob
25mm Round Angled Cap
Cable Clip
M6 x 15mm Screw
M6 x 38mm Screw
M8 x 54mm Bolt
M10 x 65mm Bolt
M10 x 138mm Bolt
25mm Thick Round Cap
M10 x 20mm Bolt
M8 x 65mm Bolt
M6 Washer
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
Handgrip
Rubber Bumper
M8 Nylon Locknut
M8 x 52mm Bolt
Pad Tube
Backrest
Seat
M10 Washer
M10 Nylon Locknut
M8 x 39mm Bolt
M8 x 50mm Carriage Bolt
Round Bushing
Butterfly Knob
Right Butterfly Arm
Stabilizer
Roll Pin
Outer Barbell
Inner Barbell
15-pound Weight
10-pound Weight
Lock Collar
User’s Manual
Exercise Guide
Grease Pack
Curl Pad
Foam Pad
25mm Square Cap
38mm x 50mm Cap
M10 x 57mm Bolt
38mm Square Cap
25mm Round Cap
19mm Round Cap
30mm Square Cap
Weight Stop
M8 Washer
Weight Clip
#
#
Note: “#” indicates a non-illustrated part. Specifications are subject to change without notice. See the back cover
of the user’s manual for information about ordering replacement parts.
Download from Www.Somanuals.com. All Manuals Search And Download.
EXPLODED DRAWING—Model No. RBBE0955.0
R0805A
27
29
50
51
20
13
35
35
34
40
24
29
50
36
12
49
50
24
26
30
12
8
26
4
51
15
50
45
28
33
45
42
51
49
42
56
9
54
17
32
24
54
31
37
25
55
4
48
17
28
32
3
16
28
25
45
48
30
48
34
51
54
47
48
24
54
43
25
28
10
1
52
28
27
16
21
17
32
37
17
18
25
55
51
2
5
32
6
27
30
15
28
30
17
44
7
28
26
39
38
41
58
17
41
31
59
17
57
28
28
27
51
27
27
15
22
63
46
53
46
14
15
41
60
23
63
29
61
19
11
29
62
23
Download from Www.Somanuals.com. All Manuals Search And Download.
ORDERING REPLACEMENT PARTS
To order replacement parts, see the front cover of this manual. To help us assist you, please be prepared to give
the following information:
1. the MODEL NUMBER of the product (RBBE0955.0)
2. the NAME of the product (REEBOK RS 100 weight bench)
3. the SERIAL NUMBER of the product (see the front cover of this manual)
4. the KEY NUMBER and DESCRIPTION of the part(s) (see the PART LIST and EXPLODED DRAWING at the
center of this manual)
LIMITED WARRANTY
ICON Health & Fitness, Inc. (ICON), warrants this product to be free from defects in workmanship and mate-
rial, under normal use and service conditions, for a period of ninety (90) days from the date of purchase. This
warranty extends only to the original purchaser. ICON's obligation under this warranty is limited to replacing
or repairing, at ICON's option, the product through one of its authorized service centers. All repairs for which
warranty claims are made must be pre-authorized by ICON. If the product is shipped to a service center,
freight charges to and from the service center will be the customer’s responsibility. For in-home service, the
customer will be responsible for a minimal trip charge. This warranty does not extend to any product or dam-
age to a product caused by or attributable to freight damage, abuse, misuse, improper or abnormal usage or
repairs not provided by an ICON authorized service center; products used for commercial or rental purposes;
or products used as store display models. No other warranty beyond that specifically set forth above is author-
ized by ICON.
ICON is not responsible or liable for indirect, special or consequential damages arising out of or in connection
with the use or performance of the product or damages with respect to any economic loss, loss of property,
loss of revenues or profits, loss of enjoyment or use, costs of removal or installation or other consequential
damages of whatsoever nature. Some states do not allow the exclusion or limitation of incidental or conse-
quential damages. Accordingly, the above limitation may not apply to you.
The warranty extended hereunder is in lieu of any and all other warranties and any implied warranties of mer-
chantability or fitness for a particular purpose is limited in its scope and duration to the terms set forth herein.
Some states do not allow limitations on how long an implied warranty lasts. Accordingly, the above limitation
may not apply to you.
This warranty gives you specific legal rights. You may also have other rights which vary from state to state.
ICON HEALTH & FITNESS, INC., 1500 S. 1000 W., LOGAN, UT 84321-9813
Part No. 230725 R0805A
Printed in China © 2005 ICON IP, Inc.
Download from Www.Somanuals.com. All Manuals Search And Download.
|