T4507-93110 (603)
OWNER/OPERATOR MANUAL
POWER AUGER
AG4300
(NOTE: Drill is optional part.)
Thank you for purchasing a RedMax
product.
WARNING
Before using our power auger, please
read this manual carefully to understand
the proper use of your unit.
The engine exhaust from this product
contains chemicals known to the State
of California to cause cancer, birth
defects or other reproductive harm.
APPLICABLE SERIAL NUMBERS : 100101 and up
Download from Www.Somanuals.com. All Manuals Search And Download.
CONTENTS
1. SAFETY PRECAUTIONS .............................................................................. 4
IN ORDER TO ENSURE PROPER AND SAFE OPERATION OF YOUR POWER AUGER
WORK GEAR AND CLOTHING
WARNINGS CONSIDERING HANDLING OF FUEL
THINGS TO CHECK BEFORE USING YOUR POWER AUGER
THINGS TO CHECK BEFORE STARTING UP THE ENGINE
AVOID NOISE PROBLEM
THINGS TO BE CAREFUL ABOUT WHEN USING YOUR POWER AUGER
NOTES ON CARE AND MAINTENANCE OF YOUR POWER AUGER
2. FUEL .............................................................................................................. 9
HOW TO MIX FUEL
FUELING THE UNIT
3. OPERATION ................................................................................................. 11
INSTALLING LEFT GRIP
INSTALLING DRILL
THROTTLE CABLE PLAY
STARTING ENGINE
STOPPING ENGINE
DRILLING
ADJUSTING CARBURETOR
4. MAINTENANCE ........................................................................................... 14
DAILY INSPECTION
PERIODICAL INSPECTION
5. STORAGE .................................................................................................... 16
BEFORE LONG-TERM STORAGE
6. SPECIFICATIONS ........................................................................................ 16
7. PARTS LIST ................................................................................................. 17
Download from Www.Somanuals.com. All Manuals Search And Download.
1. Safety Precautions
■ In order to ensure proper and safe
• Avoid running the engine indoors. The
exhaust gases contain harmful carbon
monoxide.
operation of your power auger
• Read this Owner/Operator Manual
carefully. Be sure you understand how
to operate this unit properly before you
use it. Failure to do so could result in
serious injury.
• Never use your power auger under
circumstances like those described below:
1. When the ground is slippery or when
other conditions exist which might
make it not possible to maintain a
steady posture while using the power
auger.
• Be sure to keep this manual handy so
that you may refer to it later whenever
any questions arise. Also note that you
are requested to contact the dealer from
whom you purchased the product for
assistance in the event that you have
any questions which cannot be
answered herein.
• Always be sure to include this manual
when selling, lending, or otherwise
transferring the ownership of this
product.
2. At night, at times of heavy fog, or at any
other times when your field of vision
might be limited and it would be difficult
to gain a clear view of the area where
the power auger is to be used to ensure
safety.
3. During rain storms, during lightning
storms, at times of strong or gale-force
winds, or at any other times when
weather conditions might make it
unsafe to use this product.
• This product has been designed for use in
earth drilling, and it should never be used
for any other purpose since doing so
could result in unforeseen accidents and
injuries occurring.
• When using this product for the first time,
before beginning actual work, take the
power auger to a wide, clear, open space,
turn on the power, and practice handling
the power auger until you are sure that
you will be able to handle in it properly in
actual operation.
• Lack of sleep, tiredness, or physical
exhaustion results in lower attention
spans, and this in turn leads to accidents
and injury. When planning your work
schedule, allow plenty of time to perform
the work of cutting and allow plenty of
time for rest. Limit the amount of time
over which the power auger is to be used
continuously to somewhere around 30~40
minutes per session, and take 10~20
minutes of rest between work sessions.
Also try to keep the total amount of work
performed in a single day under 2 hours
or less.
• You should never use this power auger
when under the influence of alcohol, when
suffering from exhaustion or lack of sleep,
when suffering from drowsiness as a
result of having taken cold medicine, or at
any other time when a possibility exists
that your judgment might be impaired or
that you might not be able to operate the
power auger properly and in a safe
manner. Also be sure never to allow
children or anyone unable to fully
understand the directions given in this
manual to use this power auger.
4
Download from Www.Somanuals.com. All Manuals Search And Download.
1. Safety Precautions
■ Work gear and clothing
■ Warnings considering handling of fuel
• When using your power auger, always be
sure to wear strong, durable, work
clothing; shirts should be long-sleeved
shirts and pants should be full-length
pants reaching down to the ankles.
• The engine of the power auger is
designed to run on a mixed fuel which
contains highly flammable gasoline. This
fuel is highly flammable and you should
never store cans of fuel or refill the tank of
the power auger in any place where there
is a boiler, stove, wood fire, electrical
sparks, welding sparks, or any other
source of heat or fire which might ignite
the fuel.
• Always be sure to wear and helmet and
face protector when using your power
auger.
• When using your power auger, always be
sure to wear thick work gloves to protect
your hands and non-slip-sole work boots
to prevent you from slipping. Never use
your power auger when wearing pants
with loose cuffs, when wearing sandals, or
when barefoot.
• Smoking while operating the power auger
or refilling its fuel tank is extremely
dangerous. Always be sure to keep lit
cigarettes away from the power auger at
all times.
• When using your power auger for an
extended period of time, you should wear
ear protectors to protect yourself from loss
of hearing from overexposure to high
levels of sound.
• When refilling the tank always turn off the
engine first and take a careful look around
to make sure that there are no sparks or
open flames anywhere nearby before
refueling.
• If any fuel spillage occurs during refueling,
always be sure to use a dry rag to wipe
any fuel which has been spilled onto the
power auger before turning the engine
back on again.
• After refueling, screw the fuel cap back
tightly onto the fuel tank and then carry
the power auger to a spot 10 feet or more
away from where it was refueled before
turning on the engine.
5
Download from Www.Somanuals.com. All Manuals Search And Download.
1. Safety Precautions
■ Things to check before using your
■ Things to check before starting up the
power auger
engine
• Before beginning work, look around
carefully to get a feel for the shape of the
land, and whether or not there are any
obstacles which might get in the way while
working, and remove any obstacles which
can be cleared away before beginning
work.
• Take a careful look around to make sure
that no obstacles exist within a perimeter
of 15 feet or less around the power auger
before starting the engine.
• The area within a perimeter of 45 feet of
the person using the power auger should
be considered a hazardous area into
which no one should enter while the
power auger is in use, and when
necessary yellow warning rope, warning
signs, or some other form of warnings
should be placed around the perimeter of
the area. When work is to be performed
simultaneously by two or more persons,
care should also be taken to constantly
look around or otherwise check for the
presence and locations of other people
using power auger within the work area so
as to maintain a distance between each
person sufficient to ensure safety.
• The power auger is equipped with a
centrifugal clutch mechanism which
causes the drills to begin to rotate as soon
as the engine is started by putting the
throttle into the start position. When
starting the engine, hold it firmly in place
so as to ensure that nor the throttle may
not come into contact with any obstacles
when the engine starts up.
• Never place the throttle into the high
speed position when starting the engine.
• After starting up the engine, check to
make sure that the drills stop rotating
when the throttle is moved fully back to its
original position. If the drills continue to
rotate even after the throttle has been
moved fully back, turn off the engine and
take the unit to your authorized Red Max
servicing dealer for repair.
• Before beginning work, each component
of the power auger should be checked to
make sure that it is in proper working
order and to make sure that there are no
loose screws or bolts, fuel leaks, ruptures,
dents, or any other problems which might
interfere with safe operation. Be especially
careful at this time to check that there is
nothing wrong with the drills or with the
joints by which the drills are attached to
the power auger.
■ Avoid noise problem
NOTE
Check and follow the local regulations as
to sound level and hours of operations
for power auger.
• In general, operate power auger between
8a.m.and 5p.m.on week days and 9a.m.to
5p.m.weekends. Avoid using power auger
late at night and/or early in the morning.
6
Download from Www.Somanuals.com. All Manuals Search And Download.
1. Safety Precautions
■ Things to be careful about when using
your power auger
• Never touch the muffler, spark plug, or
other metallic parts of the engine while the
engine is in operation or immediately after
shutting down the engine. These metallic
parts reach high temperatures during
operation and doing so could result in
serious burns.
• When using your power auger, grip the
handles of the power auger firmly with
both hands, place your feet slightly apart
(slightly further apart than the width of
your shoulders) so that your weight is
distributed evenly across both legs, and
always be sure to maintain a steady, even
posture while working.
• Maintain the speed of the engine at the
level required to perform drilling work, and
never raise the speed of the engine above
the level necessary.
• Always be sure never to allow other
persons to come within the work area
while drilling.
• Be especially careful not to slip if it is
raining or if rain has just stopped, as the
ground is likely to be slippery at such
times.
• If the grass or other object gets caught in
the drill during operation, always be sure
to turn off the engine before removing the
object.
• When you finish drilling in one location
and wish to continue work in another spot,
turn off the engine before carrying it to the
new location.
• Never transport the power auger over
rough roads over long distances without
first removing all fuel from the fuel tank, as
doing so might cause fuel to leak from the
tank as a result of shocks absorbed during
transport.
• Guard against hazardous situations at all
times. Warn adults to keep pets and
children away from the area. Establish a
safe method for gaining your attention
during operation. Be careful if you are
approached.
• If someone calls out or otherwise
interrupts you while working, always be
sure to turn off the engine before turning
around.
• Keep operation area clear of all persons,
particularly small children and pets.
• Never touch the spark plug or plug cord
while the engine is in operation. Doing so
may result in being subjected to an
electrical shock.
7
Download from Www.Somanuals.com. All Manuals Search And Download.
1. Safety Precautions
■ Notes on care and maintenance of your
power auger
• In order to maintain your power auger in
proper working order, perform the
maintenance and checking operations
described in this manual at regular
intervals. In the event that any parts must
be replaced or any maintenance or repair
work not described in this manual must be
performed,
please
contact
a
representative from the store nearest
RedMax authorized servicing dealer for
assistance.
• Under no circumstances should you ever
take apart the power auger or alter it in
any way. Doing so might result in the
power auger becoming damaged during
operation or the power auger becoming
unable to operate properly.
• Always be sure to turn off the engine
before performing any maintenance or
checking procedures.
• When removing, or reattaching the drills,
be sure to wear thick, sturdy gloves and
use only proper tools and equipment to
prevent injury.
• When replacing drills or any other parts or
when replacing the oil or any lubricants,
always be sure to use only RedMax
products or products which have been
certified by RedMax for use with the
power auger.
• Do not use any accessory or attachment
other than those bearing the RedMax
mark and recommended for the unit.
8
Download from Www.Somanuals.com. All Manuals Search And Download.
2. Fuel
■ RECOMMENDED MIXING RATIO
GASOLINE 50:OIL 1
WARNING
(when using ZENOAH genuine oil)
• Gasoline is very flammable. Avoid
smoking or bringing any flame or
sparks near fuel. Make sure to stop the
engine and allow it cool before
refueling the unit. Select outdoor bare
ground for fueling and move at least
3m (10ft) away from the fueling point
before starting the engine.
50:1 MIXING CHART
GASOLINE gal.
1
2
3
4
5
2-CYCLE OIL fl.oz 2.6 5.2 7.8 10.4 13
GASOLINE liter
1
2
3
4
5
2-CYCLE OIL ml 20
40
60
80 100
• Exhaust emission are controlled by the
fundamental engine parameters and
components(eq., carburation, ignition
timing and port timing) without
addition of any major hardware or the
introduction of an inert material during
combustion.
• These engines are certified to operate on
unleaded gasoline.
• Make sure to use gasoline with a
minimum octane number of 89 RON
(USA/Canada: 87AL)
• If you use a gasoline of a lower octane
value than prescribed, there is a danger
that the engine temperature may rise and
an engine problem such as piston seizing
may consequently occur.
• Unleaded gasoline is recommended to
reduce the contamination of the air for the
sake of your health and the environment.
• Poor quality gasolines or oils may damage
sealing rings, fuel lines or fuel tank of the
engine.
• The RedMax engines are lubricated by oil
specially formulated for air-cooled 2-cycle
gasoline engine use. If RedMax oil is not
available, use an anti-oxidant added
quality oil expressly labeled for air-cooled
2-cycle engine use. (JASO FC GRADE
OIL or ISO EGC GRADE)
• Do not use BIA or TCW (2-stroke water-
cooling type) mixed oil.
■ HOW TO MIX FUEL
IMPORTANT
Pay attention to agitation.
1. Measure out the quantities of gasoline
and oil to be mixed.
2. Put some of the gasoline into a clean,
approved fuel container.
3. Pour in all of the oil and agitate well.
4. Pour In the rest of gasoline and agitate
9
Download from Www.Somanuals.com. All Manuals Search And Download.
2. Fuel
again for at least one minute. As some
oils may be difficult to agitate depending
on oil ingredients, sufficient agitation is
necessary for the engine to last long. Be
careful that, if the agitation is insufficient,
there is an increased danger of early
piston seizing due to abnormally lean
mixture.
5. In the case of storing the product for a
long period of time, clean the fuel tank
after rendering it empty. Next, activate the
engine and empty the carburetor of the
composite fuel.
6. In the case of scrapping the used mixed
oil container, scrap it only at an authorized
repository site.
5. Put a clear indication on the outside of the
container to avoid mixing up with gasoline
or other containers.
NOTE
6. Indicate the contents on outside of
container for easy identification.
As lot details of quality assurance, read the
description in the section Limited Warranty
carefully. Moreover, normal wear and
change in product with no functional
influence are not covered by the warranty.
Also, be careful that, if the usage in the
instruction manual is not observed as to the
mixed gasoline, etc. described therein, it
may not be covered by the warranty.
■ FUELING THE UNIT
1. Untwist and remove the fuel cap. Rest the
cap on a dustless place.
2. Put fuel into the fuel tank to 80% of the full
capacity.
3. Fasten the fuel cap securely and wipe up
any fuel spillage around the unit.
WARNING
1. Select bare ground for fueling.
2. Move at least 10feet (3meters) away
from the fueling point before starting
the engine.
3. Stop the engine before refueling the
unit. At that time, be sure to sufficiently
agitate the mixed gasoline in the
container.
FOR YOUR ENGINE LIFE, AVOID;
1. FUEL WITH NO OIL(RAW GASOLINE) –
It will cause severe damage to the internal
engine parts very quickly.
2. GASOHOL – It can cause deterioration of
rubber and/or plastic parts and disruption
of engine lubrication.
3. OIL FOR 4-CYCLE ENGINE USE – It can
cause spark plug fouling, exhaust port
blocking, or piston ring sticking.
4. Mixed fuels which have been left
unused for a period of one month or
more may clog the carburetor and result
in the engine failing to operate properly.
10
Download from Www.Somanuals.com. All Manuals Search And Download.
3. Operation
■ INSTALLING LEFT GRIP (F1)
• Screw in the left grip to the bracket provided on
the frame and tighten the lock nut securely.
F1
(1) Left grip
(2) Bracket
(3) Lock nut
■ INSTALLING DRILL (F2)
F2
1. Slide the ring clip and remove the lock pin from
the drill.
2. Put the drill onto the auger output shaft and
insert the lock pin. Cover it with the ring clip.
(1) PTO shaft
(2) Clip band
(3) Drill
(4) Pin
F3
■ THROTTLE CABLE PLAY (F3)
• Check the throttle cable play and adjust to
1~2mm(.04~.08in.) as necessary.
(1) Lock nut
(2) Big
(3) Small
■ STARTING ENGINE
F4
1. Fill fuel and tighten the cap securely.
2. Put the switch to “START” position. (F4)
3. Close the choke. (F5)
NOTE
When restarting immediately after stopping the
engine, Ieave the choke open. (F5)
4. Push the primer pump until overflown fuel flows
out in the clear tube. (F5)
F5
NOTE
The pump operation is not necessary when
restarting the engine immediately after stopping it.
5. Push the start set button of the handle left
11
Download from Www.Somanuals.com. All Manuals Search And Download.
3. Operation
aspect while holding the throttle lever, and set
the throttle lever in the start position. (F6)
F6
(1) Engine switch
(2) Start
(3) Stop
(4) Choke lever
(5) Open
(6) Close
(7) Primer pump
(8) Throttle lever
(9) Lock button
6. While supporting the auger with your left waist
and left hand as shown in the figure, pull the
starter rope, first lightly and add force when
compression is felt. (F7)
F7
WARNING
Keep the drill clear of everything around it as it
will start rotating upon starting of engine.
7. When the engine has started, gradually open the
choke and release the throttle lever.
8. Alow the engine to warm up for a half minutes
before starting operation.
NOTE
• When re-starting immediately after stopping the
engine, keep the choke open.
• If the engine won’t start after repeated attempts,
it may be overfed with fuel. Remove and dry the
spark plug, and try to start again with the choke
open.
F8
■ STOPPING ENGINE
1. Release the throttle lever to allow the engine
idling for a few minutes
2. Put the switch to the “STOP” position. (F8)
(1) Engine switch
■ DRILLING (F9)
• Keep a firm grip of the auger at all times on a
wide stance and by holding the handle with both
12
Download from Www.Somanuals.com. All Manuals Search And Download.
3. Operation
hands.
F9
• A reacting motion may occur on the auger when
spinning drill has hit on stones or tree roots
under the ground. Always hold the auger
securely to control such motion.
• Start drilling with half-throttle, and gradually
increase the engine speed so that the drill may
get into the ground smoothly.
• When the drill has been caught in the ground
and cannot be pulled out, stop the engine and
rotate the auger counter-clockwise.
■ ADJUSTING CARBURETOR (F10,11,12)
The carburetor on your unit has been factory
adjusted, but may require fine tuning due to
change in operating conditions.
F10
Before adjusting the carburetor, make sure that
provided are clean air/fuel filters and fresh,
properly mixed fuel.
1. Stop engine and screw in both H and L needles
until they stop. Never force. Then set them back
the initial number of turns as shown below.
H needle: 13⁄8 1⁄4
F11
L needle: 11⁄4 1⁄4
2. Start engine and allow it to warm up at half-
throttle.
3. Turn L needle slowly clockwise to find a position
where idling speed is maximum, then set the
needle back
counterclockwise.
a
quarter (1/4) turn
4. Turn idle adjusting screw counterclockwise so
that the drill does not turn. If idling speed is too
slow, turn the screw clockwise.
F12
5. Make a test run and adjust the H needle for best
drilling power, not for maximum speed.
(1) Idle adjusting screw
(2) rpm up
(3) rpmdown
(4) H-needle
(5) Fuel decrease
(6) Fuel increase
(7) L-needle
(8) Fuel decrease
(9) Fuel increase
13
Download from Www.Somanuals.com. All Manuals Search And Download.
4. Maintenance
Maintenance, replacement, or repair of the
emission control device and systems may be
performed by any non-road engine repair
establishment or individual.
WARNING
Before cleaning, inspecting or repairing the
auger, make sure that the engine has stopped
and cooled down. Disconnect the spark plug
terminal to avoid accidental engine starts.
■ DAILY INSPECTION
• Check all nuts and screws are securely tightened
and no parts are missing.
• Check for leakage of fuel.
■ PERIODICAL INSPECTION
F13
AIR FILTER (F13)
Check the air filter every 50 hours of use or more
frequently if used under very dusty condition, and
clean the element in warm soapy water as
necessary. Dry completely before installing.
(1) Cover
(2) Element
F14
SPARK PLUG (F14)
Check the spark plug every 50 hours of use and
clean the gap with a wire brush. The gap should be
set to .025 in. When replacing with a new plug, use
a Champion RCJ-6Y or NGK BPMR7A.
.025 in
0.655mm
FUEL FILTER (F15)
A clogged fuel filter can cause lack of power and
poor pickup. Check the fuel filter every 25 use
hours.
F15
1. With a small wire hook, pull the fuel line and filter
out of tank.
2. Disconnect the filter assembly.
3. If necessary, replace with new filter or clean by
blowing air inside out after spraying a carburetor
cleaning solvent.
(1) Fuel filter
14
Download from Www.Somanuals.com. All Manuals Search And Download.
4. Maintenance
CYLINDER FINS (F16)
F16
Dust clogging between the cylinder fins will cause
overheating of the engine. Periodically check and
clean the cylinder fins.
(1) Intake air cooling vent
SPARK ARRESTER (F17)
This engine is equipped with a spark arresting
screen at the exhaust port. Check periodically to
see if it is good condition, especially when your
machine is to be used on any forest covered, brush
covered, or grass covered unimproved land. In the
State of California the above is required by law
(Section 4442 of the California Public Resources
Code)
F17
1. Remove the muffler guard and pry off the spark
arrester from the exhaust port.
2. Clean the metal screen with a wire brush. If
damaged, replace with new one.
(1) Muffler guard
(2) Spark arrester
GEAR BOX
Check oil level of the gear box every 50 hours of
use and change with new oil as necessary. (SAE
#80 - 90)
F18
Recommended change interval
1st: After 50 hours of use
2nd and on: Every 100 hours of use
(1) Oiling port
(2) Oil drain port
(3) Oil level
CLUTCH
Disconnect the engine from the gear box and
check the clutch condition every 100 hours of use.
Wipe off oil attached to the drum and shoes, and
replace parts with a new one if found to be worn.
15
Download from Www.Somanuals.com. All Manuals Search And Download.
5. Storage
■ Before Long-term Storage
• Drain fuel tank and run engine out until all
fuel in the carburetor is used up.
• Remove the spark plug and drop a
spoonful 2 cycle oil into the cylinder.
Crank the engine several times and
replace the plug.
Pull starter until compression is felt.
• Brush off dirt from the drill surface and
apply rust protective oil.
• Store the machine in a dry, dust-free
place.
6. Specifications
Model Name ...................................................................................................................AG4300
Engine
Displacement cu.in(cc) ........................................................................................2.53 (41.5)
Maximum power kW(HP) ....................................................................1.5 (2.0) at 7000 rpm
Carburetor ...........................................................................Diaphragm type (Walbro WYK)
ignition system ...............................................................................................Electric (T.C.I)
Spark plug .....................................................................................................NGK BPMR7A
Starter .............................................................................................................Recoil starter
Fuel .............................................................................2 cycle oil premixed gasoline (50:1 )
(when using ZENOAH genuine oil)
Fuel tank capacity fl.oz(lit) .............................................................................................32 (0.94)
Transmission .................................................................Centrifugal clutch, worm gear reduction
Gear box lubricant .......................................................................................Gear oil SAE#80-90
Reduction ratio .....................................................................................................................45:1
Grip span in (mm) .......................................................................................................21.2 (540)
Over all dimensions
Length in (mm) .....................................................................................................24.8 (630)
Width in (mm) .......................................................................................................14.4 (359)
Height w/o drill in (mm) ........................................................................................11.7 (292)
Dry weight w/o drill Ids (kg) ..........................................................................................19.3 (8.9)
Adaptable drill size
Diameter in (mm) ...................................................................................0.8 to 8 (20 to 200)
Specifications are subject to change without notice.
16
Download from Www.Somanuals.com. All Manuals Search And Download.
7. Parts list
POWER AUGER
AG4300
NOTE :
1. Use KOMATSU ZENOAH genuine parts as specified in the parts list for repair and/or
replacement.
2. KOMATSU ZENOAH does not warrant the machines, which have been damaged by the
use of any parts other than those specified by the company.
3. When placing parts orders for repair and/or replacement, check if the model name and the
serial number are applicable to those specified in the parts list, then use parts number
described in the parts list.
4. The contents described in the parts list may change due to improvement.
5. The parts for the machine shall be supplied seven (7) years after the machine is
discontinued. [It is possible that some specific parts may be subject to change of their
delivery term and list price within the limit of ten (7) years after the machine is
discontinued. It is also possible that some parts may be available even after the limit of
seven (7) years.]
July. 2001
APPLICABLE SERIAL NUMBERS : 100101 and up
17
Download from Www.Somanuals.com. All Manuals Search And Download.
7. Parts list
Fig.1 ENGINE UNIT AG4300 (S/N 100101 and up)
18
Download from Www.Somanuals.com. All Manuals Search And Download.
Fig.1 ENGINE UNIT AG4300 (S/N 100101 and up)
Key#
Description
Part Number
Q'ty Key#
Description
Part Number
Q'ty
1
2
3
4
5
6
7
8
9
CYLINDER
BOLT
848-G6D-12A0
1850-12130
4500-13120
4500-21101
2629-21130
4500-21140
06030-06201
4810-21210
1650-21220
01252-30530
04065-03212
4500-41110
1400-41220
2850-41310
1300-41320
T2100-41410
2850-41510
4500-42000
4500-51111
4500-51220
1200-51211
1200-51230
1200-51241
4500-71110
4500-71200
4500-71220
2616-71320
3356-21130
5500-72130
5500-72110
1900-72120
4500-72150
1650-43230
1000-43240
T1007-15100
1601-15120
01252-30565
3310-31720
4700-15211
4500-15221
0263-90514
4500-31110
3310-12281
4500-31210
4500-32110
4500-32120
4500-32210
5602-73110
1852-72121
T1007-73200
848-8K4-0010
T1123-75100
4500-75120
4500-75150
1850-75130
4500-75180
4500-75190
4500-75160
1140-75320
5500-75170
1
4
1
1
3
1
2
1
1
4
1
1
2
1
2
1
2
1
2
1
2
2
2
1
1
1
1
2
1
1
1
2
1
1
1
1
2
1
1
1
1
1
4
1
1
4
1
1
1
1
1
1
1
1
1
1
1
1
1
1
61 PULLEY
62 SCREW
63 PLATE
64 WASHER
65 INSULATOR
66 SCREW
4500-75210
4500-75511
4500-75310
01643-30823
4500-13161
4500-13181
4500-13150
4500-13130
T1007-81000
5602-06030
1850-81450
–––––––––
–––––––––
–––––––––
–––––––––
–––––––––
–––––––––
5602-06020
–––––––––
–––––––––
–––––––––
–––––––––
1850-81490
1850-81520
1751-81510
T1007-81250
1751-81240
1751-81130
1881-81140
–––––––––
1752-81110
5500-81120
1751-81180
1918-81170
1881-81130
1850-81530
5500-81160
0263-90550
4500-82100
4500-82130
4500-82140
2630-33610
4500-82170
4500-82180
4500-82202
5500-82221
T1015-85004
T1015-85202
4500-85300
4500-85220
5601-85260
4820-85260
T1015-85300
3302-85400
1260-85460
1600-86120
T1133-75411
4500-22110
0263-90514
1
4
1
1
1
2
1
1
1
1
1
–
–
–
–
–
–
1
–
–
–
–
1
1
1
1
1
1
1
1
2
1
1
1
1
4
1
2
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
4
1
1
1
GASKET,base
CRANKCASE COMP.
• PIN
GASKET,case
BEARING
67 GASKET,insulator
68 GASKET,carburetor
69 CARBURETOR ASS'Y
70 • REBUILT KIT
71 • • BODY ASS'Y
72 • • • SCREEN
73 • • • VALVE
74 • • • SPRING
75 • • • SCREW
76 • • • PIN
77 • • • LEVER
78 • • GASKET KIT
79 • • • DIAPHRAGM
80 • • • GASKET,diaphragm
81 • • • DIAPHRAGM,pump
82 • • • GASKET,pump
83 • BODY,purge
84 • COVER,pump
85 • PUMP,priming
86 • JET
87 • O-RING
88 • RING
89 • SWIVEL
90 • VALVE ASS'Y
91 • SCREW
92 • BRACKET
93 • NUT,adjuster
94 • SCREW,adjuster
95 • RING
96 • SCREW
97 • WASHER
OIL SEAL
OIL SEAL
10 BOLT
11 SNAP RING
12 PISTON
13 RING
14 PIN
15 RING
16 BEARING
17 WASHER
18 CRANKSHAFT COMP.
19 SHOE,clutch
20 SPRING
21 SCREW
22 WASHER
23 WASHER
24 ROTOR
25 COIL ASS'Y
26 • CORD
27 • CAP
28 • PIN
29 GROMMET
30 CAP,plug
31 SPRING
32 BOLT
33 NUT
34 KEY
35 MUFFLER ASS'Y
36 • ARRESTER
37 BOLT
38 BOLT
98 SCREW
39 GASKET,muffler
40 PLATE,muffler
41 SCREW
42 COVER
43 BOLT
44 PLATE
45 COVER
46 SCREW
47 GUARD
48 SPARKPLUG
49 GROMMET
50 CORD COMP.
51 CLAMP
52 RECOIL ASS'Y
53 • REEL
99 BODY ASS'Y
100 • PLATE,choke
101 • LEVER,choke
102 • SCREW
103 ELEMENT
104 SCREEN
105 COVER ASS'Y
106 • KNOB
107 TANK ASS'Y
108 • CAP ASS'Y
109 • • HOLDER-A
110 • • PACKING
111 • • FILTER
112 • • STOPPER
113 • PIPE COMP.
114 • FILTER ASS'Y
115 • CLIP
116 SCREW
117 LABEL
118 GUARD
119 SCREW
54 • SCREW
55 • SPRING,spiral
56 • COLLAR
57 • ARM
58 • ROPE
59 • KNOB
60 • PLATE,stopper
19
Download from Www.Somanuals.com. All Manuals Search And Download.
7. Parts list
Fig.2 DRILL and ACCESSORY GROUP AG4300 (S/N 100101 and up)
20
Download from Www.Somanuals.com. All Manuals Search And Download.
Fig.2 DRILL and ACCESSORY GROUP AG4300 (S/N 100101 and up)
Key# Part Number
Description
Q'ty Key# Part Number
Description
Q'ty
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
3209-11103
3209-11203
1800-21281
3202-11260
0260-30620
06000-06304
3202-11311
3202-11320
3200-11330
07000-02012
04065-06220
3202-11361
2510-23230
0224-40610
3010-31380
3205-21110
3200-21121
3200-21130
3206-21210
3205-21220
3200-21230
3202-21240
3200-21250
6468-91150
Gear Case Comp
Cover Comp
Oil Seal
Gasket
Screw
Bearing
Retainer
Oil Seal
O-Ring
O-Ring
Snap Ring
Plug
O-Ring
Bolt
Gasket
Worm
Collar
Drum
1
1
1
1
6
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
2
0~3
4
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
85
86
87
88
89
90
91
92
93
94
95
96
97
98
99
100
101
102
103
104
3206-52200
3206-52220
01225-40620
0280-10605
0290-20615
3206-52330
3200-51130
3200-51140
3206-52300
3206-52320
01225-40620
0280-10605
0290-20615
3206-52330
3200-51130
3200-51140
3206-52400
3202-52420
01225-40620
0280-10605
0290-20615
3206-52330
3200-51130
3200-51140
3206-61100
3206-61120
6468-91150
0280-10605
3200-51130
3200-51140
3204-53100
3200-51130
3200-51140
3204-53200
3200-51130
3200-51140
1075-96100
1400-96210
1400-96300
3206-91610
3206-91620
3206-53430
3206-53410
3206-53420
S90 Drill Ass'y (3.5in dia.)
• Tip, S90
• Screw
• Nut
• Washer
• Bit
• Pin
• Clip
S150 Drill Ass'y (5.9in dia.)
• Tip, S150
• Screw
• Nut
• Washer
• Bit
• Pin
• Clip
S200 Drill Ass'y (7.9in dia.)
• Tip, S200
• Screw
• Nut
• Washer
• Bit
• Pin
• Clip
L150 Drill Ass'y (5.9in dia.)
• Blade
• Bolt
• Nut
• Pin
• Clip
L100 Joint Ass'y
• Pin
• Clip
1
1
2
2
2
1
1
1
1
1
3
3
3
1
1
1
1
1
3
3
3
1
1
1
1
2
2
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
Shaft
Wheel
Washer
Washer
Shim
Bolt
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
01010-50620
01602-20619
01643-30623
3209-31123
3206-31130
0225-50630
3206-31202
3206-31212
3206-31220
1000-15150
0280-10605
0290-20615
3204-31300
3204-31310
4050-14220
0281-11411
T4507-12511
3206-91001
3541-91110
1030-91340
3239-91310
3540-91120
3540-93120
3202-51102
3202-51121
3200-51130
3200-51140
3206-52100
3202-52121
01225-40620
0280-10605
0290-20615
3206-52330
3200-51130
3200-51140
Bolt
2
2
2
2
4
4
1
1
2
2
2
4
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
2
2
2
1
1
1
Washer
Washer
Holder
Spacer
Bolt
Bracket Ass'y
• Bracket
• Mount
• Nut
• Nut
L300 Joint Ass'y (11.8in.)
• Pin
• Clip
• Washer
Left Handle Comp
• Handle-L
• Grip
Puller Ass'y
Set Block
Rod Ass'y
Spanner
Rod
Tip, S300
Tip, S200
Tip, S250
• Nut
Name Plate
Tool set
• Bag
• Screwdriver
• Socket
• Spanner
Band
S40 Drill Ass'y (1.6in dia.)
• Bit
• Pin
121
122
123
124
125
126
127
128
129
130
T4502-31110
01252-31025
01602-21030
T4502-31120
3577-32141
848-8R2-0314
T4502-73220
T4502-73230
T4502-73240
T4502-83100
Frame
bolt
Washer
Bracket, Frame
Grip
Lever
Cord
Cord
Tube
1
2
2
1
1
1
1
1
1
• Clip
S60 Drill Ass'y (2.4in dia.)
• Tip, S60
• Screw
• Nut
• Washer
• Bit
Cable Comp
• Pin
• Clip
21
Download from Www.Somanuals.com. All Manuals Search And Download.
RedMax
LIMITED WARRANTY
EMISSION-RELATED PARTS, FOR TWO (2) YEARS FROM THE DATE OF ORIGINAL DELIVERY OF THE UNIT,
RedMax / KOMATSU ZENOAH AMERICA, INC., THROUGH ANY RedMax DEALER, WILL REPAIR OR REPLACE, FREE OF
CHARGE, FOR THE ORIGINAL AND EACH SUBSEQUENT PURCHASER, ANY PART OR PARTS FOUND TO BE DEFECTIVE
IN MATERIAL AND/OR WORKMANSHIP.
EMISSION-RELATED PARTS ARE:
THE CARBURETOR ASSEMBLY, COIL ASSEMBLY, ROTOR, SPARKPLUG,
AIR FILTER, FUEL FILTER, INTAKE MANIFOLD, AND THE GASKETS
ALL OTHER PARTS EXCEPT ABOVE PARTS, FOR TWO (2) YEARS OF USE, 90 DAYS FOR RENTAL USE, FROM THE
DATE OF ORIGINAL PURCHASE, THE COMPANY, THROUGH ANY RedMax DEALER, WILL REPAIR OR REPLACE, FREE
OF CHARGE, FOR THE ORIGINAL PURCHASER, ANY PART OF PARTS FOUND TO BE DEFECTIVE IN MATERIAL AND/OR
WORKMANSHIP. THIS IS THE EXCLUSIVE REMEDY.
THE PURCHASER SHALL BEAR COSTS OF TRANSPORTING THE UNIT TO AND FROM THE RedMax DEALER.
THE PURCHASER SHALL NOT BE CHARGED FOR DIAGNOSTIC LABOR WHICH LEADS TO THE DETERMINATION
THAT A WARRANTED PART IS DEFECTIVE, IF THE DIAGNOSTIC WORK IS PERFORMED AT THE RedMax DEALER.
THE PURCHASER OR OWNER IS RESPONSIBLE FOR THE PERFORMANCE OF THE REQUIRED MAINTENANCE AS
DEFINED BY THE MANUFACTURER IN THE OWNER/OPERATOR MANUAL.
ANY WARRANTED PART WHICH IS NOT SCHEDULED FOR REPLACEMENT AS REQUIRED MAINTENANCE, OR
WHICH IS SCHEDULED ONLY FOR REGULAR INSPECTION TO THE EFFECT OF "REPAIR OR REPLACE AS
NECESSARY" SHALL BE WARRANTED FOR THE WARRANTY PERIOD. ANY WARRANTED PART WHICH IS
SCHEDULED FOR REPLACEMENT AS REQUIRED MAINTENANCE SHALL BE WARRANTED FOR THE PERIOD OF
TIME UP TO THE FIRST SCHEDULED REPLACEMENT POINT FOR THE PART.
ANY REPLACEMENT PART THAT IS EQUIVALENT IN PERFORMANCE AND DURABILITY MAY BE USED IN NON-
WARRANTY MAINTENANCE OR REPAIRS, AND SHALL NOT REDUCE THE WARRANTY OBLIGATION OF THE
COMPANY.
THE COMPANY IS LIABLE FOR DAMAGES TO OTHER ENGINE COMPONENTS CAUSED BY THE FAILURE OF A
WARRANTED PART STILL UNDER WARRANTY.
THE WARRANTY DOES NOT APPLY TO THOSE UNITS WHICH HAVE BEEN DAMAGED BY NEGLIGENCE OF
INSTRUCTION LISTED IN THE OWNER/OPERATOR MANUAL FOR PROPER USE AND MAINTENANCE OF THE UNITS,
ACCIDENTAL MISHANDLING, ALTERATION, ABUSE, IMPROPER LUBRICATION, USE OF ANY PARTS OR ACCESSORIES
OTHER THAN THOSE SPECIFIED BY THE COMPANY, OR OTHER CAUSES BEYOND THE COMPANY'S CONTROL.
THIS WARRANTY DOES NOT COVER THOSE PARTS REPLACED BY NORMAL WEAR OR HARMLESS CHANGES IN
THEIR APPEARANCE.
THERE ARE NO OTHER EXPRESS WARRANTIES.
IMPLIED WARRANTIES INCLUDING THOSE OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE
ARE LIMITED TO TWO (2) YEARS OF USE FROM THE ORIGINAL DELIVERY DATE.
LIABILITIES FOR INCIDENTAL OR CONSEQUENTIAL DAMAGE UNDER ANY AND ALL WARRANTIES
ARE EXCLUDED.
SOME STATES DO NOT ALLOW LIMITATION ON HOW LONG AN IMPLIED WARRANTY LASTS OR EXCLUSION OR
LIMITATION OF INCIDENTAL OR CONSEQUENTIAL DAMAGES, SO THE ABOVE LIMITATION OR EXCLUSION MAY
NOT APPLY TO YOU.
THIS WARRANTY GIVES YOU SPECIFIC LEGAL RIGHTS, AND YOU MAY ALSO HAVE OTHER RIGHTS WHICH VARY
FROM STATE TO STATE.
IF YOU NEED TO OBTAIN INFORMATION ABOUT THE NEAREST SERVICE CENTER, PLEASE CALL RedMax / KOMATSU
ZENOAH AMERICA, INC. AT (770)-381-5147.
IMPORTANT: YOU WILL RECEIVE A WARRANTY REGISTRATION CARD AT TIME OF PURCHASE.PLEASE FILL
OUT THE CARD AND SEND IT TO RedMax / KOMATSU ZENOAH AMERICA WITHIN SEVEN (7) DAYS. BE SURE TO KEEP
A COPY FOR YOUR RECORDS.
KOMATSU ZENOAH AMERICA INC.
4344 Shackleford Road Suite 500
Norcross, Georgia 30093
Download from Www.Somanuals.com. All Manuals Search And Download.
RedMax
Garantie limitée
Pièces en rapport avec les émissions de gaz d'échappement : RedMax / KOMATSU ZENOAH AMERICA, INC.,
par l'intermédiaire de n'importe quel revendeur RedMax, réparera gratuitement ou remplacera gratuitement pour
l'acheteur initial et chaque acheteur successif toute(s) pièce(s) se révélant de constitution et/ou de montage
défectueux pendant deux (2) ans à compter de la date initiale de livraison d’une unité.
Les pièces en rapport avec les émissions de gaz d'échappement sont:
l'assemblage carburateur, l'assemblage bobine, le rotor, la bougie,
le filtre à air, le filtre à carburant, la tubulure d'admission et les joints
Toutes les pièces autres que celles mentionnées ci-dessus, deux (2) ans d’utilisation, 90 jours pour la location, à
compter de la date d’achat initial. La société, par l’intermédiaire d’un distributeur RedMax, réparera ou remplacera
toute(s) pièce(s), sans frais et au bénéfice de l’acheteur original, en prenant en charge les frais de pièces et/ou de
main d’œuvre. Telles sont les limites de la garantie.
Le coût du transport de l'unité jusqu'au revendeur RedMax et depuis celui-ci sera à la charge de l'acheteur.
L'acheteur ne supportera pas le coût de main d'oeuvre du diagnostic qui amène à la conclusion qu'une pièce
garantie est défectueuse, si ce diagnostic est effectué chez le revendeur RedMax.
L’acheteur ou propriétaire a pour responsabilité d’effectuer l’entretien obligatoire tel que défini par le fabricant dans le
manuel du propriétaire/de l'utilisateur.
Toute pièce garantie dont le remplacement n'est pas prévu dans le cadre de l’entretien obligatoire, ou pour laquelle
est seulement prévue une inspection périodique pour "remplacement ou réparation si nécessaire" sera garantie pour
la période de garantie. Toute pièce garantie arrivée à l’échéance de son premier remplacement prévu sera garantie
jusqu’à celui-ci.
Toute pièce de rechange équivalente en performance ou en durabilité peut être utilisée pour l’entretien hors-garantie
ou les réparations hors-garantie, et ce sans réduire l’obligation de garantie incombant à la société.
La société sera tenue responsable des dommages aux autres composants du moteur causés par la défaillance de
pièce(s) garantie(s) en période de garantie.
La garantie ne s'applique pas aux unités endommagées par suite de: négligence dans la mise en oeuvre des
instructions spécifiées dans le manuel du propriétaire/de l'utilisateur en vue d’une utilisation et d’un entretien correct,
fausse manœuvre accidentelle, modification, utilisation abusive, lubrification incorrecte, utilisation de pièces ou
d’accessoires autres que ceux spécifiés par la société, ou autres causes hors du contrôle de la société.
Cette garantie ne couvre pas les pièces remplacées en raison de leur usure normale ou de changements
d’apparence sans effets.
Il n'existe aucune autre garantie explicite.
Les garanties implicites, y compris la valeur marchande et la valeur d’usage pour une utilisation particulière, sont
limitées à deux (2) ans d’utilisation à compter de la date originale de livraison.
Les responsabilités pour les dommage conséquents ou incidents sont exclues de toutes les garanties.
Certaines provinces n'autorisant pas les limitations à la durée des garanties implicites, ou les exclusions ou
limitations relatives aux dommages incidents ou conséquents, la limitation indiquée ci-dessus peut ne pas vous être
applicable.
Cette garantie vous donne des droits juridiques spécifiques, et vous pouvez également jouir d’autres droits variant
d'une province à l'autre.
Si vous désirez obtenir des informations sur le centre de service le plus proche, veuillez appeler RedMax /
KOMATSU ZENOAH AMERICA, INC. au (770)-381-5147
Note importante: vous recevrez une carte d'enregistrement de garantie au moment de l'achat. Veuillez la remplir et
l'adresser à RedMax / KOMATSU ZENOAH AMERICA sous sept (7) jours en prenant soin de conserver une copie
pour vous.
KOMATSU ZENOAH AMERICA INC.
4344 Shackleford Road Suite 500
Norcross, Georgia 30093
Download from Www.Somanuals.com. All Manuals Search And Download.
KOMATSU ZENOAH AMERICA INC.
4344 Shackleford Road Suite 500
Norcross, Georgia 30093
© Printed in Japan
Download from Www.Somanuals.com. All Manuals Search And Download.
|