Razor Bicycle 20036560 User Guide

Flash RideR 360°  
Owner’s Manual  
Read and understand this entire manual before riding!  
DO NOT RETURN TO STORE!  
NOTE: Manual illustrations are for demonstration purposes only. Illustrations  
may not reflect exact appearance of actual product. Specifications subject to  
change without notice.  
Item Number:  
20036560  
v.1_10-11  
Download from Www.Somanuals.com. All Manuals Search And Download.  
BEfORE yOU BEGIN  
Remove contents from box and check parts against parts diagram found on page 6. Remove the foam separators that  
protect the components from damage during shipping. Inspect the contents of the box for scratches in the paint or  
dents that may have occurred during shipping. Because the Flash Rider 360˚ was partially assembled and packed at the  
factory there should not be any problems, even if the box has a few scars or dents.  
WARNING: DO  
NOT USE NON-RAZOR  
PRODUCTS WITH YOUR  
Flash Rider 360˚.  
The Flash Rider 360˚ has been  
built to certain Razor design  
specifications. The original  
equipment supplied at the time of  
sale was selected on the basis of  
its compatibility with the frame,  
fork and all other parts. Certain  
aftermarket products may or may  
not be compatible and will void  
your warranty.  
q Estimated Assembly and Set-Up Time  
Allow up to 15–20 minutes for assembly.  
Front Fork Assembly  
Steering Bolt  
Front Wheel Assembly  
Spark Handle  
Seat  
Pedals  
Spark Bar  
Rear Caster Wheels  
Spark Cartridge Cover  
Spark Cartridge  
q Required Tools  
(2) 5mm  
Allen wrenches  
(included)  
10mm and 13mm  
open wrenches  
(included)  
Need Help? Visit our web site for replacement parts and product support at www.razor.com, or call toll-free  
at 866-467-2967 Monday - Friday 8:00 AM - 5:00 PM Pacific Time.  
2
Download from Www.Somanuals.com. All Manuals Search And Download.  
ASSEMBLy AND SET-UP  
q Attaching the front fork  
Required Tools: 13mm open wrench and 5mm Allen wrench  
WARNING: Failing  
to properly tighten the steering  
bolt that attaches the front fork  
assembly to the frame assembly,  
can cause you to lose control and  
fall.  
1 Remove the steering bolt and  
locknut from the frame assembly  
with a 13mm open wrench and  
5mm Allen wrench.  
2 Insert the front fork into the  
3 Be sure to properly align slot in  
headset tube with pin on fork as  
shown.  
frame assembly.  
4 Re-insert the steering bolt  
and secure with locknut using a  
13mm open wrench and 5mm Allen  
wrench.  
q Attaching the front Wheel  
Required Tools: 5mm Allen wrench and 10mm open wrench  
1 Remove the four coupling  
bolts from the front fork with a  
5mm allen wrench and 10mm  
open wrench.  
2 Insert the wheel assembly into  
the front fork assembly and align  
holes. When installing the wheel,  
make sure the letter “F” and arrow  
(located on the side of the wheel)  
are facing the direction as shown  
above.  
3 Re-insert the coupling bolts  
through the front fork and tighten  
securely.  
3
Download from Www.Somanuals.com. All Manuals Search And Download.  
ASSEMBLy AND SET-UP  
q Attaching the Rear Caster Wheels  
Required Tools: 5mm Allen wrench  
1 Insert the caster bolt into the  
frame. If aligned correctly, the caster  
thread should go half way into the  
frame with no resistance.  
2 Using a 5mm Allen wrench,  
tighten the hex bolt located on the  
underside of the wheel cover until  
the caster bolt is all the way inside  
the frame.  
3 If you’re having trouble thread-  
ing the caster into frame, use a rag  
or small brush with a little WD-  
40® to remove any excess particles  
that may be caught in or around the  
threading within the frame.  
Note: Make sure the spring washer  
is on the caster bolt before inserting  
the caster.  
Note: There should be no visible  
threading between the frame and  
the wheel cover (See Inset)  
q Attaching the Seat  
Required Tools: (2) 5mm Allen wrench  
1 Remove the four coupling  
bolts from the frame using two  
5mm Allen wrenches; one on top  
and one on bottom.  
2 Align the four holes in seat  
with the four holes in frame. Insert  
coupling bolts through the top and  
bottom of the frame.  
3 Tighten bolts using two 5mm  
Allen wrenches; one on top and  
one on bottom.  
Need Help? Visit our web site for replacement parts and product support at www.razor.com, or call toll-free  
at 866-467-2967 Monday - Friday 8:00 AM - 5:00 PM Pacific Time.  
4
Download from Www.Somanuals.com. All Manuals Search And Download.  
SET UP AND USAGE INSTRUCTIONS  
q Replacing the Spark Cartridge:  
Friction during sparking will eventually wear out the replaceable cartridge and cause the scooter to stop making  
sparks. Worn out cartridges must be replaced.  
WARNING: Do not  
attempt to replace cartridge  
immediately after riding as  
cartridge will be hot. Handle only  
when cool.  
WARNING: Keep fingers  
clear of Spark Bar hinge.  
1 Using your thumbs, press tabs  
on both sides of the cartridge to  
release from the bracket. Slide car-  
tridge away from you and remove  
from bracket.  
2 Place a new cartridge in back of the bracket making sure to align the slots  
on the cartridge with the two legs of the bracket. Slide cartridge forward  
until you hear a click and the thumb tabs are locked in place.  
WARNING: Pulling  
the Spark Handle upwards too  
strenuously may cause loss of  
control.  
q Using the Spark Handle  
NOTE: Sparks and Spark  
cartridge life will vary based on  
the amount of pressure applied  
by spark handle, the length of  
time pressure is applied and  
the smoothness of the riding  
surface.  
NEVER push down directly on the Spark Bar, spark  
cartridge or spark cartridge cover itself.  
1 Pull up on the handle to operate sparking feature.  
5
Download from Www.Somanuals.com. All Manuals Search And Download.  
fLASH RIDER 360˚ CASTER TRIkE PARTS  
Keep your Flash Rider 360˚ rolling for years with genuine Razor parts. Visit our website to purchase replacement parts.  
(Specifications subject to change without notice.)  
1
2
Handlebar Grip (x2)  
6
7
8
9
Rear Wheel Assembly (x2)  
Seat  
Front Fork  
2-1 Front Fork Coupling Bolts (x4)  
Front Cover  
Spark Handle  
Spark Bar  
3
4
Steering Bolt  
10 Spark Cartridge  
4-1 Lock Nut  
11 Spark Cartridge Cover  
5
Front Wheel w/ Pedals and Cranks Complete  
6
Download from Www.Somanuals.com. All Manuals Search And Download.  
SAfETy REMINDERS  
PRE-RIDE CHECkLIST  
Loose Parts  
Tire Care  
Check and secure all fasteners before every ride. Make sure  
the steering bolt and casters are tight. There should not be any  
unusual rattles or sounds from loose parts or broken components.  
If you are not sure, ask an experienced mechanic to check.  
Periodically inspect the wheels for excess wear.  
q
q
q
q
frame, fork and Handlebars  
Check for cracks or broken connections. Although broken frames  
are rare, it is possible for an aggressive rider to crash into a curb  
or wall and wreck and bend or break a frame. Get in the habit of  
inspecting yours regularly.  
Safety Gear  
Always wear proper protective equipment, such as an approved  
safety helmet. Elbow pads and knee pads are recommended.  
Always wear shoes (lace-up shoes with rubber soles), never ride  
barefooted or in sandals, and keep shoe laces tied and out of the  
way of the wheels.  
DO NOT RETURN TO STORE  
failure to follow these instructions may damage  
your product and void your warranty.  
WARRANTy  
Razor Limited Warranty  
For your records, save your original sales receipt with this manual.  
__________________________________________  
The manufacturer warranties this product to be free of manufacturing defects  
for a period of 6 months from date of purchase. This Limited Warranty does  
not cover normal wear and tear, or any damage, failure or loss caused by  
improper assembly, maintenance, storage or use of the Razor Flash Rider 360˚.  
Item Number:  
20036560  
This Limited Warranty will be void if the product is ever  
• used in a manner other than for recreation;  
• modified in any way;  
• rented.  
The manufacturer is not liable for incidental or consequential loss or damage  
due directly or indirectly to the use of this product.  
Razor does not offer an extended warranty. If you have purchased an  
extended warranty, it must be honored by the store at which it was  
purchased.  
Need Help? Visit our web site for replacement parts and product support at www.razor.com, or call toll-free  
at 866-467-2967 Monday - Friday 8:00 AM - 5:00 PM Pacific Time.  
U.S. Patent No. D593,910 S  
Printed in China for:  
Razor USA LLC  
PO Box 3610  
Cerritos, CA 90703  
Copyright © 2003-2012 Razor USA, LLC. All rights reserved. RAZOR and the Razor Logo De-  
sign are among the registered trademarks of Razor USA LLC in the United States and/or select  
foreign countries. Flash Rider is a trademark of Razor USA LLC.  
10/2011  
7
Download from Www.Somanuals.com. All Manuals Search And Download.  

Pyramid Technologies Speaker PW1086 X User Guide
Radio Shack Speaker 40 4092 User Guide
Radio Shack Watch 63 5086 User Guide
RCA Blu ray Player BRC3109 User Guide
ResMed Respiratory Product Adapt SV System User Guide
RIDGID Impact Driver R84230 User Guide
Rival Fondue Maker FD350S CN User Guide
Samsung Car Video System 305T User Guide
SanDisk Computer Drive Cruzer Profile User Guide
Scion Automobile 00505 QRG10 TC User Guide