|
SL520/530/631 PLUS
Chartplotter
Display
Owner’s
Handbook
Document number: 81209_1
Date: September 2002
Download from Www.Somanuals.com. All Manuals Search And Download.
iii
SL520/530/631 PLUS Chartplotter Display
Owner’s Handbook
September 2002
INTENDED USE
The display units detailed in this handbook may form part of navigational
radar systems intended for light marine use. These displays and radar
systems are only an aid to navigation.
SAFETY NOTICES
This equipment must be installed and operated in accordance with the
instructions contained in this manual. Failure to do so can result in personal
injury and/or navigational inaccuracies. In particular:
1. HIGH VOLTAGE. The LCD display unit unit contains high voltages.
Adjustments require specialized service procedures and tools only
available to qualified service technicians – there are no user serviceable
parts or adjustments. The operator should never remove the display unit
cover or attempt to service the equipment.
2.NAVIGATIONAID. Thisunitisonlyanaidtonavigation. Itsaccuracycan
be affected by many factors, including equipment failure or defects,
environmental conditions, and improper handling or use. It is the user’s
responsibility to exercise common prudence and navigational judgements.
This unit should not be relied upon as a substitute for such prudence and
judgement.
Download from Www.Somanuals.com. All Manuals Search And Download.
iv
SL520/530/631 PLUS Chartplotter Displays
Raymarine products are supported by a network of Authorized Service
Representatives. For information on our products and services, contact either
of the following:
UNITED STATES Raymarine Inc.
22 Cotton Road, Unit D
Nashua, NH 03063-4219
Telephone: +1 603 881 5200
+1 800 539 5539
Fax:
+1 603 864 4756
EUROPE
Raymarine Limited
Anchorage Park
Portsmouth
Hampshire PO3 5TD
England
Telephone: +44 (0) 23 9269 3611
Fax:
+44 (0) 23 9269 4642
Copyright © Raymarine Ltd. 2002
The technical and graphical information contained in this handbook, to the
best of our knowledge, was correct as it went to press. However, our policy of
continuous improvement and updating may change product specifications
withoutprior notice. As a result, unavoidable differences between the product
and handbook may occur from time to time, for which liability cannot be
accepted by Raymarine.
Raymarine is a registered trademark of Raymarine Limited.
SeaTalk is a registered trademark of Raymarine Limited.
Pathfinder Plus is a trademark of Raymarine Limited.
ThisproductcontainstechnologyprovidedunderlicensebyAcornGroupplc.
The copyright of this intellectual property is acknowledged by Raymarine
Ltd., as are Acorn’s trademarks and patents. Acorn’s world wide web address
is http://www.acorn.com.
Download from Www.Somanuals.com. All Manuals Search And Download.
v
Preface
This handbook describes the following PLUS displays from Raymarine:
System
Display
Scanner Chartplotter
Chartplotter - Mono 7” Display
Color 7” Display
SL520 PLUS
SL530 PLUS
SL631 PLUS
No
No
No
Yes
Yes
Yes
Color 10.4” Display
Note: The display units include a cartridge holder assembly which contains
two slots for C-MAP NT chart cards.
This handbook contains very important information on the installation and
operation of your new equipment. In order to obtain the best results in
operation and performance, please read this handbook thoroughly.
Raymarine’s Technical Services representatives or your local dealer will be
available to answer any questions you may have.
TFT Color LCD Displays
The colors of the display may seem to vary when viewed against a colored
background or in colored light. This is a perfectly normal effect that will be
seen with all color LCD displays.
In commonwith allThin FilmTransistor(TFT)LCDdisplays, thescreenmay
exhibit a few (less than 20) wrongly illuminated pixels. These may appear as
black pixels in a light portion of the screen, or as colored pixels in black areas.
CAUTION:
To provide protection against the damaging effects of UV light, it is
advisabletoreplacethesuncoverprovidedwhenthecolorLCDdisplayis
not in use.
Warranty
To register your display unit ownership, please take a few minutes to fill out
the warranty registration card found at the end of this handbook. It is very
important that you complete the owner information and return the card to the
factory in order to receive full warranty benefits.
Download from Www.Somanuals.com. All Manuals Search And Download.
vi
SL520/530/631 PLUS Chartplotter Displays
EMC Conformance
All Raymarine equipment and accessories are designed to the best industry
standards for use in the recreational marine environment.
The design and manufacture of Raymarine equipment and accessories
conform to the appropriate Electromagnetic Compatibility (EMC) standards,
but correct installation is required to ensure that performance is not
compromised.
Download from Www.Somanuals.com. All Manuals Search And Download.
vii
Contents
Preface ............................................................................................ 1.v
Warranty ....................................................................................... 1.v
Chapter 1: Overview ..........................................................................................1.1
1.1 General .......................................................................................... 1.3
Soft Keys ..................................................................................... 1.10
Pop-Up Menus .............................................................................1.11
Database Lists ............................................................................. 1.12
2.1 Introduction .................................................................................. 2.1
Conventions Used ......................................................................... 2.1
Simulator ...................................................................................... 2.1
2.2 Switching the Display On and Off ................................................ 2.2
Simulator Mode ............................................................................ 2.3
Changing the Lighting & Contrast - SL520 Mono Display .......... 2.4
Changing the Brightness - SL530/631 Color Display .................. 2.5
2.3 Controlling the Display ................................................................. 2.6
Selecting the Mode of Operation .................................................. 2.6
Customizing the Screen Presentation Options ............................ 2.10
2.4 Chart Display Control Functions ................................................ 2.12
Moving Around the Chart ........................................................... 2.12
2.5 Typical Chart Scenarios .............................................................. 2.16
Place and Goto a Waypoint ......................................................... 2.18
Download from Www.Somanuals.com. All Manuals Search And Download.
viii
SL520/530/631 PLUS Chartplotter Displays
3.1 Introduction .................................................................................. 3.1
Creating a New Route ................................................................. 3.19
Clearing the Current Route ......................................................... 3.23
Retrieve a Route From the Database ........................................... 3.23
Displaying Route Information .................................................... 3.24
Using the Route List to Erase and Name a Route ....................... 3.26
Editing a Route ........................................................................... 3.27
3.5 Following Routes and Going to Points ....................................... 3.29
Follow a Route ............................................................................ 3.29
Target Point Arrival .................................................................... 3.31
Other Follow Route Options ....................................................... 3.31
Going To an Individual Target Point ........................................... 3.32
Stop Follow or Stop Goto ............................................................ 3.33
3.6 Transferring Waypoints and Routes ........................................... 3.34
3.7 Using Tracks ............................................................................... 3.37
Setting Up a Track ...................................................................... 3.38
Download from Www.Somanuals.com. All Manuals Search And Download.
Clearing the Current Track ......................................................... 3.39
Managing Tracks ........................................................................ 3.39
Chapter 4: Further Chart Operations ..............................................................4.1
4.1 Introduction .................................................................................. 4.1
4.3 Alarms and Timers ........................................................................ 4.4
Alarm Reporting ........................................................................... 4.4
Setting Alarms and Timers ........................................................... 4.5
4.5 Cursor Echo .................................................................................. 4.7
4.6 GPS Setup ..................................................................................... 4.8
5.1 Introduction .................................................................................. 5.1
Cursor Reference .......................................................................... 5.6
Cursor Readout ............................................................................. 5.6
Day/Night ..................................................................................... 5.6
Help ............................................................................................... 5.7
Soft Keys ....................................................................................... 5.7
Key Beep ...................................................................................... 5.7
MOB Data ..................................................................................... 5.7
Autopilot Pop Up .......................................................................... 5.7
Menu Timeout Period ................................................................... 5.7
Units .............................................................................................. 5.7
Variation Source ........................................................................... 5.8
Bridge NMEA Heading ................................................................ 5.8
NMEA Out Set Up ........................................................................ 5.9
Cursor Echo .................................................................................. 5.9
Date and Time Settings ................................................................. 5.9
Download from Www.Somanuals.com. All Manuals Search And Download.
x
GPS SOG/COG Filter ................................................................. 5.10
Compass Set Up .......................................................................... 5.10
5.4 Chart Set Up Parameters...............................................................5.11
Chart Orientation ........................................................................ 5.12
Object Information ..................................................................... 5.13
Waypoint Options ....................................................................... 5.13
Vectors ........................................................................................ 5.13
Position Offset ............................................................................ 5.14
Chapter 6: Installation ......................................................................................6.1
6.1 Introduction .................................................................................. 6.1
Planning the Installation ............................................................... 6.2
6.2 Unpacking and Inspecting the Components ................................. 6.4
6.4 Cable Runs .................................................................................... 6.9
Power Cable .................................................................................. 6.9
6.5 Mounting the Display Unit ......................................................... 6.10
6.6 System Connections ................................................................... 6.12
Display Unit Connection ............................................................ 6.13
6.7 System Checks and Inital Switch On .......................................... 6.15
System Check ............................................................................. 6.15
Switch On and Initial Setup ........................................................ 6.15
EMC Conformance ..................................................................... 6.16
6.8 Integrated Systems ...................................................................... 6.17
SeaTalk® and NMEA In ............................................................. 6.18
Using the SeaTalk Auxiliary Junction Box ................................. 6.21
Data Output ................................................................................. 6.22
Data Conversion ......................................................................... 6.23
Download from Www.Somanuals.com. All Manuals Search And Download.
xi
Received Data ............................................................................. 6.24
Transmitted Data ........................................................................ 6.24
Chapter 7: Maintenance and Problem Solving ..............................................7.1
7.1 Maintenance ................................................................................. 7.1
Routine Checks ............................................................................. 7.1
EMC Servicing and Safety Guidelines ......................................... 7.1
7.2 Resetting the System ..................................................................... 7.2
7.3 Problem Solving ........................................................................... 7.3
Technical Support: ........................................................................ 7.3
How to Contact Raymarine (US) .................................................. 7.4
How to Contact Raymarine (Europe) ........................................... 7.5
Worldwide Support ....................................................................... 7.5
Appendix A: Specification ...................................................................................A.1
SL520/530/631 PLUS Displays ...................................................A.1
Appendix B: C-MAP Chart Card Features .......................................................... B.1
Appendix C: SeaTalk and NMEA Data Received and Transmitted ................ C.1
Appendix D: Abbreviations .................................................................................D.1
Index ............................................................................................. 1.xiii
Download from Www.Somanuals.com. All Manuals Search And Download.
xii
SL520/530/631 PLUS Chartplotter Displays
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 1: Overview
1-1
Chapter 1: Overview
How to Use This Handbook
This handbook describes the following displays:
SL520 PLUS Chartplotter, 7" Mono Display
SL530 PLUS Chartplotter, 7" Color Display
SL631 PLUS Chartplotter, 10.4" Color Display
If you are installing the display system yourself, you should read Chapter 6
will be useful if you are connecting your system to other equipment.
For an overview of the display unit controls and the chartplotter system, read
Chapter 1. Chapter 2 will help you start using your system.
For chartplotter operating details, refer to Chapter 3 and Chapter 4.
To change the system set up defaults, read Chapter 5.
you see on your display depends on your system configuration and set up op-
tions, so it may differ from the illustration.
This handbook is organized as follows:
Chapter 1 provides an overview of the features and functions of the Display.
This chapter also provides an overview of the controls. You should read this
chapter to familiarize yourself with the system.
Chapter 2 explains how to start using the display and describes how to use
some of the basic chart functions. Chapter 2 also provides operating
guidelines fortypicalchartplotter scenarios; these guidelines introduce you to
many of the chartplotter functions.
Chapter 3 provides detailed operating information for the standard
chartplotter functions - using chart cards, plotting waypoints and routes,
following routes and showing tracks.
Chapter 4 providesdetailedoperatinginformationforfurtherchartfunctions,
including measuring distances, man overboard and cursor echo. It includes
instructions for setting up a differential GPS.
Chapter 5 provides instructions for setting up your system to suit your
preferences. You should read this chapter to determine how to set up the
system defaults.
Chapter 6 provides planning considerations and detailed instructions for
installingthe displayunit. It should bereferredtowhenyouarereadytoinstall
Download from Www.Somanuals.com. All Manuals Search And Download.
1-2
SL520/530/631 PLUS Chartplotter Displays
the system. Details to connect the display to other equipment are also
provided.
Chapter 7 provides information on user maintenance, and what to do if you
experience problems.
The Appendices provide additional information that you may find useful:
Appendix A lists the technical specifications for the chartplotter.
Appendix B defines the chart features shown on the chart display.
Appendix C defines the SeaTalk and NMEA data that is transferred on
integrated systems.
Appendix D provides a list of abbreviations.
An Index and warranty information are included at the end of the handbook.
A summary of the chartplotter controls are provided on the Quick Reference
Card supplied with your system.
Terminology
The following terminology is used to describechartplotter systems:
Master
A unit capable of sourcing specific data such as
chart data.
Radar Display
Chart Display
Unit providingRadar Master functionality.
Unit providing Chart Master functionality.
Integrated System Additional instruments are connected via the
Seatalk or NMEA interfaces.
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 1: Overview
1-3
1.1 General
The display unit is waterproof to CFR46 and can be installed either above or
below deck.
The unit includes:
•
•
•
•
•
7" or 10.4" PLUS display
Trackpad
Eleven dedicated (labeled) control keys
Four soft keys (unlabeled) whose functionality changes
®
Two slots for the C-MAP NT chart cards
The display and keys can be illuminated for night-time use.
PLUS Display Units
Features
•
•
•
•
Displays chart information from the C-MAP NT® chart cards (C-Cards)
Uses position data from GPS, DGPS, WAAS or Loran-C technology
Displays and transfers SeaTalk and NMEA data
Half-screen windows to display additional data: Course Deviation Indica-
tor (CDI), Bearing and Distance Indicator (BDI), navigation data.
•
•
•
Cursor echo across SeaTalk
Choice of orientation: Head Up, Course Up and North Up
The system can be connected to an ST80 Navigator keypad for entry of
alpha-numeric data.
Set Up Options
Set up options allow you to choose what is displayed, how it is displayed
(including language and units), bearing mode and how the display operates
with other equipment. You can view the cursor position and a variety of data
fromotherequipment, e.g. speed, heading, depth, windandtideinformationin
a set of user-selectable data boxes. For systems with an autopilot, when the
status and locked heading information change the new data can be displayed.
DisplayoptionsareprovidedinSystemSetUp, describedinChapter 5.Screen
Presentation Options, described in Chapter 2 allow you to switch the cursor
and data boxes On/Off. The cursor box and user-selected data boxes can be
moved around the screen.
Download from Www.Somanuals.com. All Manuals Search And Download.
1-4
SL520/530/631 PLUS Chartplotter Displays
Operating Modes
You can view a full screen chart.You can also set Windows On to split the
display into two half-screen windows to show supplementary data. The main
operating mode (chart) is displayed in the upper window; you choose what is
displayed in the lower window.
The following are available:
j
Table 1-1:
Operating Modes and Window Options
Display
Full-screen mode
Chart
CDI, BDI or Nav Data
SL520/530/631
Data Log Mode
Windows not available
Half-Screen Window Options
•
Chart display: can be displayed full screen or in a half-screen window.
•
CDI: This gives the Course Deviation Indicator graphical display, with
data relating to the target waypoint.
•
•
BDI:ThisgivestheBearingandDistanceIndicatorgraphicaldisplay, with
data relating to the target waypoint.
Nav Data: This shows nine (mono display) or sixteen (color display) data
boxes, providing navigational data in the units specified in your set up.
Note that up to 6 of these data boxes are also available as a user-selectable
group (see Section 5.3).
You select the operating mode and windows using the DISPLAY key as
described in Chapter 2.
Heading and Position Data
Fullfunctionalityofthechartplotter isachievedwhenitispartofanintegrated
system with other equipment connected via SeaTalk or NMEA 0183. Data
from this equipment including position and heading is shown on the display
and is used in calculations.
Details on connecting other equipment are given in Chapter 6.
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 1: Overview
1-5
1.2 The Chartplotter Display
The SL520/530/631 PLUS display includes a Chartplotter. The chartplotter
includes a small-scale world map and detailed navigation information is
displayed when a cartographic chart card is installed. The details displayed
depend on the chart zoom level selected. A plotter mode is provided to enable
route plotting and tracking at large scales even when a chart card is not
installed, or when the chart is zoomed beyond the available cartographic
detail. A typical chartplotter screen is shown in Figure 1-1.
The chartplotter uses position information from a GPS, DGPS, WAAS or
Loran-C instrument. Once the position fix has been established, your vessel’s
position, if on screen, is shown as a boat shape pointing in the direction of the
current heading (or COG if heading data is not available). If no heading or
COG data is available, the vessel is shown as a circle.
The chartplotter screen includes a status bar that displays chart scale, with
either cursor position, range and bearing or, when the cursor is homed to the
vessel (by pressing FIND SHIP), vessel position, Speed Over Ground (SOG),
Course Over Ground (COG) and fix type (VES POS, DIF FIX or SD FIX).
Any waypoints you have placed are displayed (unless you turned them off in
Information can be viewed on-screen by positioning the cursor over a
waypoint, current route or chart object. The chartplotter screen can also show
additional information, depending on your currently selected options, set up
selections and data available from other equipment.
An example chart display, in its default configuration, with a chart card
installed, is shown in the following illustration.
Several functions are available to control the display as follows:
•
•
Zoom in/out and Pan the Display
Offset the Chart or Center the Chart around the Vessel
Operation of these functions is described in Chapter 2.
Chartplotter Display Options
In addition to the display set up options previously described, chart set up
options, describedin Chapter 5, allowyouto customize the chartby selecting:
•
•
•
•
What cartographic features and level of detail are displayed.
The chart color palette (sunlight or shade) - color displays only.
Chart orientation (north up, head up or course up), datums and position offset.
How waypoints are displayed (symbols and numbers) and the availability
of chart object identification data.
•
Vectors for heading, COG and tide.
Download from Www.Somanuals.com. All Manuals Search And Download.
1-6
SL520/530/631 PLUS Chartplotter Displays
The Screen Presentation Options, described in Chapter 2 allow you to switch
the Chart Grid On/Off and Custom Chart Details On/Off.
Note: Whenyouturn thedisplayoffandonagain, theScreenPresentationset-
tings are retained in memory.
Status Bar
Chart Range
Chart Boundary
Waypoint
Vessel Position
Cursor -
selecting chart object
Depth Area
Cursor position box
Shows the current
cursor position as
either Range/Bearing
or Lat/Long. You can
move this box to your
preferred position on
the screen or turn it off.
Object data box -
for object selected
by cursor
Default soft key labels
These can be turned off: press any soft key to redisplay them.
Different labels are displayed when you press a key.
D4275-2
Figure 1-1: Typical Chartplotter Display
Custom Chart Details
The chartplotter set up options include a sub-menu to customize the
cartographic features. This menu allows you to switch features On, Off, or
control them using the CUSTOM soft key. The factory default settings for the
Custom chart options are as follows:
ON:
Chart text, chart boundaries, depth contours, navigation marks
and land features.
OFF:
Caution and routing data.
CUSTOM: Spot sounding, light sectors, marine features.
Note: The factory default for the CUSTOM settings is ON.
Icons are displayed in detail, depth shading limit is 10 m and depth contour
display is 0-100 m.
A complete list of chart features is given in Appendix B.
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 1: Overview
1-7
Chartplotter Functions
The Chartplotter includes the following functions:
Display C-MAP NT C-Card chart information including Ports and Tides
(if available)
• View chart information (if available) for the Nearest Port
•
•
•
•
•
•
•
•
•
•
•
Place, Move, Erase and Edit a Waypoint
Goto Waypoint or Cursor
Create, Save, Name, Edit and Follow a Route
Review Route and Waypoint Lists
Display vessel’s track; Save and Name the Track for re-call to screen
SmartRoute to make a track into a route
Measure Chart Distances and Bearings on-screen
Set Up Alarms and Timers
Man OverBoard (MOB) to navigate back to a missing person or object
Differential GPS set up page
Operation of these functions is described in Chapter 3 and Chapter 4.
Download from Www.Somanuals.com. All Manuals Search And Download.
1-8
SL520/530/631 PLUS Chartplotter Displays
1.3 Operating Controls
You operate the chart using a variety of controls:
•
A trackpad providing up, down, left, right and diagonal control of an on-
screen cursor.
•
•
•
•
Eleven dedicated (labeled) control keys.
Four soft keys with labels displayed on the screen.
Pop-up menus, displayed on-screen, from which you select options.
Database lists, displayed on-screen, which enable you to edit items.
Note: The cursor is the cross-hair symbol (+) visible on the display. You move
the cursor using the trackpad and use it to select a position or item on the chart.
ThecontrolkeysareshowninFigure 1-2.Theyareback-litfornight-timeuse.
When you use a control, a help message is displayed at the top of the screen
(unless you switch help off as described in Chapter 5). The following
paragraphs describe the controls and on-screen facilities.
Dedicated
keys
Trackpad
Soft keys
Dedicated keys
D3596-3
Figure 1-2: LCD Display Control Keys
Trackpad and Cursor
The trackpad has several functions:
•
•
•
To move the cursor around the screen
To select an item from a pop-up menu
To adjust a variable soft key control
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 1: Overview
1-9
The cursor is used to:
•
•
•
Select a position on the screen.
Select an item, e.g. chart object.
Pan the chart display.
Moving the Cursor
You can press on any of the four sections of the trackpad to move the cursor in
move diagonally. The cursor moves faster as you continue to press the
trackpad. The current cursor position is shown in the cursor data box (if
selected).
Note: During many operations you cannot move the cursor around the
screen;ifyoucannotmovethecursorusingthetrackpad,checkthedefaultsoft
keys are displayed (unless they have been switched OFF in system set up). If
not, press ENTER until they are displayed.
The cursor is normally displayed as a crosshair. However, if you have not
movedthecursorformorethanfiveseconds, whenyounextmoveitthecursor
is outlined by a circle so it is easier to locate on the screen.
Context-Sensitive Cursor Control
The cursor is context-sensitive. When the cursor is positioned over special
features on the display a text label appears to identify the feature as detailed in
Table 1-2 .
Moving and deleting items with the context-sensitive cursor
Some items on the chartplotter screen have information associated with them.
Most information is displayed in a data box. The context-sensitive cursor
allows you to move databoxes. It also allows you to move or delete other
items. Further details of items that can be moved or deleted are given in the
appropriate sections throughout this handbook.
➤ To move any data box or selectable item:
1. Usethetrackpad to positionthecursorovertheitemuntiltheitem’slabelis
displayed.
2. Press ENTER to take control of the item, use the trackpad to move it to the
required position.
3. Press ENTER again to fix the position, or press CLEAR to abandon the
move.
➤ To delete an item:
1. Usethe trackpadto positionthecursorovertheitemuntiltheitem’slabelis
displayed then press CLEAR.
Download from Www.Somanuals.com. All Manuals Search And Download.
1-10
SL520/530/631 PLUS Chartplotter Displays
Table 1-2:
Text Label
BOX
Context-Sensitive Cursor Text Labels
Feature
Data box (any type)
Man Over Board marker
Chart Waypoint
Ruler line
MOB
WPT
A➟B
COG
Course Over Ground vector
Heading vector
Vessel’s position
Route leg
HDG
POS
RTE
TIDE
Tide vector
Dedicated Keys
The dedicated keys: DISPLAY, MARKS, VRM/EBL, MULTI ALARMS,
RANGE, ENTER, CLEAR, MENU and POWER have fixed functions; the
functions are similar on all Pathfinder displays. For example, ALARMS is
used to set up the system alarms on both a chartplotter and a radar.
Some keys can be used in two ways:
•
Press: Press the key momentarily and then release it. This method is used
for most key operations.
•
Pressandhold:Pressthekeyandholditdownforthelengthoftimestated
(for example, 3 seconds), and then release it.
When you press a dedicated key, one of the following happens:
i. The associated operation is actioned, e.g. change chart scale (RANGE).
ii. A pop-up menu is displayed, providing further options.
iii. A set of soft keys is displayed, providing further functions.
As you press a key, a single audio beep confirms the key action. If the key-
press is not valid for the current screen or mode, three rapid beeps sound to
indicate that no response is available. If required, you can turn the key beeps
off as part of your set up procedure (see Chapter 5).
Soft Keys
The four keys below the screen are called soft keys because their functions
change according to the operation. The soft keys are grouped into related sets
and subsets providing access to the various functions. The soft key labels are
displayedonthescreenjustabovethekeys.Thedefaultsoftkeysaredisplayed
until you press a key, or select an item on the screen; the soft keys associated
with the action are then displayed.
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 1: Overview
1-11
ROUTE
GOTO
SCREEN FIND SHIP
D4160-1
The currently selected soft key option is shown by its gray or green
background. If the key text is displayed in gray rather than in black, it is not
currently available.
When you press a soft key one of the following happens:
i. The associated operation is actioned, e.g. NORTH UP.
ii. A sub-set of soft keys is displayed, providing further functions.
iii. A pop-up menu is displayed, providing further options.
As with dedicated keys, when you press a soft key a single audio beep
confirms the key action. If the key-press is not valid for the current screen or
mode, three rapid beeps sound to indicate that no response is available. If
required, you can turn the key beeps off as part of your set up procedure (see
Chapter 5).
Pop-Up Menus
Pop-up menus usually provide set up options. When a pop-up menu is on-
screen, a set of associated soft keys is also displayed as shown in Figure 1-3.
You use the trackpad to select an option from the menu, then use the
appropriate soft key to set the option. For example, you can toggle the OFF
TRACK ALARM on/off.
ALARMS SET UP
ARRIVAL ALARM
0.01nm
ON
OFF TRACK ALARM
ANCHOR ALARM
OFF
GROUNDING ALARM
COUNTDOWN TIMER
ALARM CLOCK
5M/1.0nm
00:33:00
OFF
SELECT ARRIVAL
ALARM RADIUS
D4265-4
Figure 1-3: Typical Pop-up Menu
Download from Www.Somanuals.com. All Manuals Search And Download.
1-12
SL520/530/631 PLUS Chartplotter Displays
Database Lists
The waypoints, routes and tracks that you create on the chartplotter are stored
in database lists. You can view these lists and select items for editing.
WAYPOINT LIST
NAME
SYMBOL
WAYPOINT 001
WAYPOINT 002
WAYPOINT 003
WAYPOINT 004
WAYPOINT 005
POSITION
50°21^966N
001°20^368W
BRG _186°
RNG _21.0nm
TEMP
DEPTH
---°C
---m
DATE
TIME
--/--/--
--:--:--
GOTO
WAYPOINT WAYPOINT WAYPOINT TRANSFER
EDIT
MAKE NEW WAYPOINT
D4262-2
Figure 1-4: Typical Database List
As with pop-up menus, when a database list is on-screen, a set of associated
soft keys is also displayed; you use the trackpad to select an item from the list,
then use the appropriate soft key to edit the item. For example, you can erase a
waypoint or a route.
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 2: Getting Started & Adjusting the Display
2-1
Chapter 2: Getting Started & Adjusting the
Display
2.1 Introduction
This chapter provides information and instructions to get you started using
your display. It will help you to become familiar with the display and the
functionsofthe controlsbeforeyou startusing the unit. Chartplotteroperating
Conventions Used
Throughout this handbook, the dedicated (labelled) keys are shown in bold
options are shown in normal capitals; for example, SCREEN.
Operating procedures, which may consist of a single key-press or a sequence
of numbered steps, are indicated by a ➤ symbol in the margin.
When theprocedurerequiresyou to pressa softkey, the softkeyicon isshown
in the margin.
Simulator
The display unit includes a simulator function, that allows you to practice
operating your Chartplotter without data from the GPS system. You will need
to use the set up options to switch the display to simulator mode, as described
in Section 2.2. You can use it in either of two ways:
•
Before the display unit has been installed on your vessel. In this case, you
only need to connect the display to a 12V or 24V DC power supply, con-
necting the red core from the power lead to positive (+) and the black core
to negative (-). See Chapter 6 for full details.
•
After the display has been installed on your vessel, but while in the marina
or at anchor.
The following section, Section 2.2, includes instructions to view simulated
chart images.
Download from Www.Somanuals.com. All Manuals Search And Download.
2-2
SL520/530/631 PLUS Chartplotter Displays
2.2 Switching the Display On and Off
➤ To switch the display on, press and hold the POWER key until the unit beeps.
If the display was last used in chartplotter mode, the keys light up and the
Raychart graphic is displayed, followed by the caution:
CAUTION:
Raychart chart displays are based on cartographic data that
C-MAP believes to be accurate. However, you should not rely on these
displays as your primary source of navigation. Rather, your Raychart
should be used only as a backup to official government charts and
traditional methods of navigation.
When you have readand understood the caution, presstheCONTINUE soft key.
The chart is displayed.
If this is the first time the chartplotter has been turned on, and no chart card is
installed, the display shows the small-scale world map and the default soft
keys. Otherwise, the display shows the selected chart area and any data that
were displayed when the display was last used.
Until unit beeps
D4277-2
Figure 2-1: Switch On - Chart Mode
Switch Off
CAUTION:
To provide protection against the damaging effects of UV light, it is
advisabletoreplacethesuncoverprovidedwhenthecolorLCDdisplayis
not in use.
A reminder is displayed when you switch off the color LCD display.
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 2: Getting Started & Adjusting the Display
2-3
➤ To switch the display unit off, press and hold the POWER key for three
seconds. A countdown timer is displayed as shown below:
GAIN
VRM/EBL
MULTI
DISPLAY
MARKS
Countdown timer:
number of seconds
to power off
POWER OFF IN
3s
ALARMS
RANGE
POWER
ENTER
CLEAR
MENU
3
SECONDS
D3599-1
Figure 2-2: Switch Off
When the counter reaches zero a beep sounds, and the display unit switches
off. Release the POWER key.
Note: Switch the display unit off before you remove the power cord.
Simulator Mode
When simulator mode is on a simulator data box is displayed.
When thedisplayisswitchedoffthen on again, simulatormode ismaintained.
It is recommended that you select the System Set Up Menu and switch off
simulator mode when you have finished.
➤ To view a simulated image:
MENU
1. Press MENU followed by the SYSTEM SET UP soft key.
SYSTEM
SET UP¬
The set up menu pop-up is displayed.
2. UsethetrackpadtomovetheselectionbarovertheoptionSIMULATOR.The
simulator soft keys are displayed.
3. In the system set up menu, press DATA to view the chart display with simu-
lated position.
4. Press ENTER twice to return to the default display.
Note: Any waypoints placed on the chartplotter in simulator mode are re-
tained in the database list and are available for use in routes.
Download from Www.Somanuals.com. All Manuals Search And Download.
2-4
SL520/530/631 PLUS Chartplotter Displays
Changing the Lighting & Contrast - SL520 Mono Display
You can change the level of backlighting and contrast for the screen and keys.
The key lighting is set the same as the screen lighting, except that it remains
switched on at its lowest level even when the screen lighting is turned off, so
that you can always find the keys.
➤ To change the lighting and contrast:
1. Press the MULTI key to display the soft key controls:
The last-used softkey is highlighted in inverse video (white text on a black
background).
If you press MULTI during the magnetron warm-up sequence countdown,
only the LIGHT and CONTRAST sliders are displayed, and the lighting is
automatically switched on at its last-used level.
ON
O
F
F
A
U
T
O
25%
50%
ALARM
LIGHT
CONTRAST
TUNE
D3935-3
75%
2. To select a control (if it is not already highlighted) press the soft key.
Alternatively, you can press the trackpad left and right edges to move side-
ways between the controls to select the soft key.
LIGHT
3. If necessary, press the soft key to toggle the control ON/OFF.
4. Use the trackpad (up or down) to increase or decrease the setting (between
0 and 100 in 1% steps). You can press and hold the trackpad to change the
setting more rapidly. The lighting/contrast level is adjusted as you change
the setting.
50%
CONTRAST
5. PressENTER toremovethesoftkeyslidersandreturntothedefaultscreen,
with the new lighting and contrast levels retained, or press CLEAR to dis-
card the changes and return to the default screen.
If lights are left ON when you switch off the display, the next time the display
is switched on, the lightswillbe ON, butatthe default setting of 40%. The new
contrast level is retained until you reset it, unless you set the control very low
or very high; in this case, the contrast will be restored as follows:
Contrast set < 30% restored to 30%
Contrast set > 70 % restored to 70%
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 2: Getting Started & Adjusting the Display
2-5
Changing the Brightness - SL530/631 Color Display
The MULTI key on the color LCD display is used to adjust brightness. The
brightness of the screen can be adjusted over a wide range, suitable for
viewing in daylight (high brightness level) or at night (low brightness level).
The key lighting is automatically adjusted as you alter the screen lighting, so
that you can always find the keys. If you set the backlight to a high level, the
key lighting is dimmed; if you set the backlight to a low level, the key lighting
level is increased.
Adjusting the Brightness
➤ To change the screen brightness:
1. Press the MULTI key to display the soft key controls :
75%
LIGHT
D6109_1
2. The LIGHT soft key indicates the brightness level, use the trackpad (up or
down) to increase or decrease the setting. You can press and hold the track-
pad to change the setting more rapidly. The brightness level is adjusted as
you change the setting.
3. Press ENTER to return to the default screen, with the new brightness level.
➤ To set the screen brightness to 100%:
Press and hold the MULTI key for one second. The brightness is increased to
MULTI
100%.
The brightness level is retained when you switch off the display.
Note: During night-time use, the brightness may be set very low, when subse-
quently operated during the day it may not be apparent that the display is on;
press MULTI, followed by the second soft key from the left, then use the track-
pad to increase brightness. Alternatively, press and hold MULTI for one sec-
ond to set the brightness to 100%.
Download from Www.Somanuals.com. All Manuals Search And Download.
2-6
SL520/530/631 PLUS Chartplotter Displays
2.3 Controlling the Display
You control the display using the cursor and control keys. You start all
operations from the default screen, that is the default soft keys are displayed:
ROUTE
GOTO
SCREEN FIND SHIP
D4160-1
When you have completed an action using the soft keys, press ENTER or
CLEAR to return to the default screen; you may need to press ENTER or
CLEAR several times to back-track through the soft key hierarchy.
Note: If you have set up your system so that the default soft keys are not dis-
played all the time, press any soft key to display the labels.
The remainder of this section describes how to select the mode of operation
and switch half-screen windows on/off. The following sections describe how
to set up the display.
The controls are summarized in the fold-out illustration on page 2.8.
Selecting the Mode of Operation
You use the DISPLAY key to select the full-screen mode.
The following modes can be selected:
•
•
Chart
Data log
The DISPLAY key also accesses the soft keys for the half-screen window
options.
➤ To changethemode, pressthe DISPLAYkey to show the DISPLAYpop-up, then
press again to toggle between chart and data log modes.
DISPLAY
The selected mode is shown by an icon with a red border and the mode is
displayed on the screen. The associated half-screen window soft keys are also
displayed.
When the required mode is shown, press ENTER or CLEAR. The default soft
keys are displayed. The selected mode is shown full-screen; in Chart mode
you can switch on half-screen windows for additional display, as described in
the following section.
If you press DISPLAY again, the pop-up and soft keys for the current mode are
shown.
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 2: Getting Started & Adjusting the Display
2-7
Selecting a Half-Screen Window for Display
Note: Windows can only be used with the Chart screen, they are not available
on the data log screen.
➤ To select a window for display:
1. Press the DISPLAY key. The following soft are displayed with an image of
each available window:
WINDOWS
OFF ON
SELECT
WINDOWS
DISPLAY
D4156-2
2. To select a different window, press either SELECT WINDOWS soft key until
the required window is highlighted. If necessary, this will toggle windows
on. Press ENTER.
3. To toggle windows off, press the WINDOWS OFF ON soft key.
Figure 2-3 shows the half-screen horizontal windows.
Returning to the Full-Screen Display
To return to the full-screen display you can turn windows off, as previously
described. Alternatively, to return to full-screen display:
DISPLAY
➤ Press and hold the DISPLAY key for 2 seconds to return to the currently
selected full-screen (upper window) display.
Download from Www.Somanuals.com. All Manuals Search And Download.
2-8
SL520/530/631 PLUS Chartplotter Displays
Fold out sheet Radaronly /chartonly Display
Download from Www.Somanuals.com. All Manuals Search And Download.
2-10
SL520/530/631 PLUS Chartplotter Displays
Customizing the Screen Presentation Options
The SCREENsoftkey lets youswitch thefollowing screenpresentationoptions
on or off:
CRSR BOX CHRT GRID DATABOXES CUSTOM
OFF ON
OFF ON
OFF ON
OFF ON
D4177-1
Switching the Cursor Data Box On and Off
Thecursordata boxprovidesthecursor’s position in latitude/longitudeand/or
bearing/range. If you wish to see a full image, you can switch the data box off.
➤ To control the cursor data box:
1. Press the SCREEN soft key.
SCREEN
2. PresstheCRSR BOX softkey totogglethesettingfromOFF to ONorfromON
CRSR BOX
OFF ON
to OFF.
3. To return to the default soft key display, press ENTER.
➤ Youcan use thecontextsensitivecursortoselectandmove thecursordatabox
(the label BOX is displayed). See Moving and deleting items with the context-
sensitive cursor on page 1-9
BOX
Switching Chart Grid On and Off
The Chartplotter display includes grid lines of latitude and longitude which
you can use to help determine position on the chart. The grid lines can be
switched on if required.
➤ To turn the chart grid on or off:
SCREEN
1. Press the SCREEN default soft key.
2. Press the CHRT GRID soft key to toggle the setting from OFF to ON or from
ON to OFF.
To return to the default soft key display, press ENTER.
Data Boxes
Agroupofuptosixdataboxescanbedisplayed, iftheinformationisavailable
on your system. You select which data is displayed in the boxes during
system set up as described in Chapter 5:Setting Up the System Defaults.
The default data box positions are along the bottom of the display. Each box
canbemovedtotherequiredpositiononthescreenusingthecontext-sensitive
cursor.
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 2: Getting Started & Adjusting the Display
2-11
Note: If youselect BDI, CDIor Nav Data fordisplay in a half-screen window,
the data boxes are temporarily hidden.
At any time, you can switch the group ofdataboxes onoroffusingtheSCREEN
soft key. When first installed, the boxes are all OFF. When the display unit is
OFF) and positions.
SCREEN
Note: The SCREEN soft key does not control the nine or sixteendata boxes that
can be displayed in the half-screen window.
➤ To switch the group of data boxes on or off:
1. Press the SCREEN default soft key.
SCREEN
2. Press the DATABOXES soft key to toggle the setting from ON to OFF or from
DATABOXES
OFF ON
OFF to ON.
To return to the default soft key display, press ENTER.
If you turn the data boxes on and none are displayed, you need to select the
ones you require using the system set up menu, as described in Section 5.3,
System Set Up Parameters.
➤ You can use the context sensitive cursor to select and move any data box (the
label BOX is displayed). See Moving and deleting items with the context-
sensitive cursor on page 1-9
BOX
Custom Options
When chart details have been customized in the Chart Set Up menu (as
describedin Section 5.4)theSCREENsoftkeycanbeusedtoswitchthecustom
chart options off or on:
When set to ON, all chart options set to CUSTOM in the Customize Chart menu
are displayed; when set to OFF, options set to CUSTOM are not shown.
The factory default for custom chart options is ON.
➤ To switch the customized options on or off:
1. Press the SCREEN default soft key.
SCREEN
2. Press the CUSTOM soft key to toggle the setting from OFF to ON or from ON
CUSTOM
OFF ON
to OFF.
To return to the default soft key display, press ENTER.
Download from Www.Somanuals.com. All Manuals Search And Download.
2-12
SL520/530/631 PLUS Chartplotter Displays
2.4 Chart Display Control Functions
Moving Around the Chart
You will normally operate the chartplotter with the chart showing your
vessel’s current location. The default orientation is North-Up, and the vessel
moves across the screen. You will need to move the chart if your vessel moves
out of the area currently displayed, or if you wish to examine or place
waypoints in another area. Alternatively, you can home the cursor onto the
vessel using FIND SHIP.
There are four ways in which you can move the chart:
•
Use the trackpad to move the cursor to the edge of the chart. The chart will
pan across. This method is useful if the area you wish to see is only just off
the screen.
•
•
•
Use the context-sensitive cursor to change the chart center.
Automatically re-center the vessel using the FIND SHIP soft key.
Change the chartscale to zoom outandin to a new areacentered on the cur-
tance away.
Changing the Chart Center
You can move the area of the chart displayed on the screen using the context-
sensitive cursor. This allows you to center your vessel in the middle of the
screen, or to move the chart so that your vessel is displayed off-center
anywhere on the screen.
➤ To center the chart:
1. Usethetrackpadtomovethecursortothevessel’sposition. Thecursortext
POS
POS is displayed.
2. Press CLEAR. The chart is moved so that your vessel’s position is in the
center of the screen.
➤ You use the context sensitive cursor to select and move your vessel’s position
off-center (the label POSis displayed). See Moving and deleting items with the
context-sensitive cursor on page 1-9.
POS
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 2: Getting Started & Adjusting the Display
2-13
D4278-1
Figure 2-4: Changing the Chart Center
Using FIND SHIP
FINDSHIP isusedinchartmodetore-drawthechartwiththevesselatthecenter
and the cursor homed onto the vessel.
ROUTE
GOTO
SCREEN FIND SHIP
D4160-1
When you press FIND SHIP the following occur:
•
•
•
The chart is re-drawn with the vessel’s position in the center.
The cursor is homed onto the vessel position and moves with it.
When the vessel moves near the edge of the chart window, the chart is
redrawn to place the vessel and cursor at the center again.
•
The status bar indicates vessel position, speed and course over ground.
➤ To release the cursor from homed mode press the trackpad to move the cursor
away from the vessel’s current position. The status bar shows the cursor
position, range and bearing.
Changing the Chart Scale
The RANGE key allows you to change the chart scale so that you can see a
smaller or larger area on the screen.
Plotter mode is available to allow you to zoom into a smaller area, even when
nochart data is available for thatscale. Section 5.4describes how to set plotter
mode on/off.
You can change the chart scale for two purposes:
Download from Www.Somanuals.com. All Manuals Search And Download.
2-14
SL520/530/631 PLUS Chartplotter Displays
•
•
To see either more detail (of a smaller area) or a larger area (in less detail)
on the screen.
To move the display to another area of the chart, by zooming out to a small
scale chart, then zooming in on another position centered on the cursor.
The cartographic detail available on charts varies according to the chart scale
and some areas include detail at smaller scales than others. This can cause
blank areas on the display when adjacent areas with different levels of detail
are displayed. To reduce this affect you can use the Chart Set Up options (see
Section 5.4)tosetchartdisplaydetailtosimple. Then, asyouzoomin, charted
areas are displayed but with less detail shown.
Each time you press the RANGE key, the chart scale changes to the next
available setting. The status bar indicates the distance from top to bottom of
the screen, in nautical miles.
Vertical distance
Increases the
displayed on chart
chart distance
RANGE
CSR 50 45'980N
POS 001 01'490W
Decreases the
chart distance
6nm
Status Bar
D4175_1
Figure 2-5: Changing the Chart Scale
➤ To change the scale quickly, press and hold the required arrow on the RANGE
key.
RANGE
whenever you change the chart scale.
➤ To zoom in to a larger-scale (more detailed) chart:
1. Use the trackpad to position the cursor in the area you wish to see in more
detail.
2. Press the lower part of the RANGE key to zoom into the area.
The section of the chart around the cursor is enlarged to fill the screen with
a larger-scale chart showing more detail. The cursor is now positioned in
the center of the screen.
RANGE
The distance indicated at the top left of the screen is updated.
3. If further chart enlargement is available using the current chart card you
can press the bottom of the RANGE key to zoom in again, re-positioning
the cursor first if required.
An area of further chart detail is indicated by a box around the area as
shown in Figure 2-6.
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 2: Getting Started & Adjusting the Display
2-15
Chart Boundary -
indicates further
detail is available inside
D4279-1
Figure 2-6: Chart Boundaries
4. When no further chart detail is available, as you press the bottom of the
RANGE key, the effect depends on whether Plotter Mode is on or off as
follows:
• If Plotter Mode is Off, the chart scale remains unchanged, indicating
the smallest chart scale is displayed.
Note: If Plotter Mode is Off and the cursor is homed to the vessel (see
Using FIND SHIP on page 2-13), if the vessel moves outside an area of
available cartography, the chart will automatically re-scale to the next
range with cartography.
• IfPlotter Mode isOn, the scale isdecreased and the messageNOCHART
DATA is displayed. The vessel, waypoints, routes and tracklines are dis-
played without cartography.
Thechartinformationisrestoredwhenyoureturntoachartscaleforwhichthe
information is available.
➤ Tozoomouttoasmaller-scale(lessdetailed)chart, simplypresstheupperpart
RANGE
of the RANGE key as many times as required.
Download from Www.Somanuals.com. All Manuals Search And Download.
2-16
SL520/530/631 PLUS Chartplotter Displays
2.5 Typical Chart Scenarios
Thefollowingillustrationsprovideoperatingguidelinesfortypicalnavigation
scenarios. These scenarioscan be used asa trainingguide; they show you how
to perform a particular operation and they introduce many of the chartplotter
functions.
Each scenarioindicatesthekey pressesrequiredtoperformparticular tasks. A
typical chartplotter screen image is shown for each task.
The scenarios assume you have read the previous sections of this chapter and
that you are familiar with the Operating Controls. Full operating details for
each function are provided in Chapter 3 and Chapter 4.
Operating guidelines are provided for the following scenarios:
•
•
•
Working with Waypoints
Place a Waypoint
Goto a Waypoint
Make and Follow a Route
Create a Route
Follow a Route
Review the Passage Plan
View Route Information
Change the SOG, Hours and ETA.
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 2: Getting Started & Adjusting the Display
2-17
This page intentionally left blank.
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 2: Getting Started & Adjusting the Display
2-19
4
The vessel navigates towards the target
waypoint
See:
5.3 Working wth Waypoints
Go to an individual Target Point,
page 5-26.
D4267-2a
Download from Www.Somanuals.com. All Manuals Search And Download.
2-20
SL520/530/631 PLUS Chartplotter Displays
Make and Follow a Route
#
1
Press the soft key
2
Press the soft key
3
1. Position Cursor - in this example
over an existing waypoint
2. Press the soft key
4
Position Cursor for next waypoint,
then press soft key.
Repeat to plot all waypoints in
sequence.
D4268-1
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 2: Getting Started & Adjusting the Display
2-21
5
Press the soft key. The route becomes
the current route.
6
Press the soft key
7
Press the soft key
8
The vessel starts to navigate to the
first (target) waypoint in the route.
See:
5.4 Working wth routes,
Follow a route, page 5-24.
Other Follow Options, page 5-25.
D4268-2a
Download from Www.Somanuals.com. All Manuals Search And Download.
2-22
SL520/530/631 PLUS Chartplotter Displays
Review Your Passage Plan
1
Press the soft key
2
3
4
Press the soft key
Press the soft key
1. Use the trackpad to move
selection bar over required route.
2. Press the soft key
5
Time defaults to ETA - and assumes
the current time is the start time.
D4269-1
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 2: Getting Started & Adjusting the Display
2-23
6
See:
Displaying Route Information
page 5-18.
Change the TIME to HOURS - the display
indicates it will take 32 minutes to reach
the destination. You can change the
PLANNED SOG; the display updates to
indicate TIME required at the planned
speed.
D4269-2a
Download from Www.Somanuals.com. All Manuals Search And Download.
2-24
SL520/530/631 PLUS Chartplotter Displays
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 3: Standard Chart Operations
3-1
Chapter 3: Standard Chart Operations
3.1 Introduction
display. It covers the following topics:
•
•
Using chart cards.
Controlling waypoints, including placing, moving, editing and deleting
waypoints.
•
Working with routes, including creating a new route, managing routes
using the route database and editing routes.
•
•
•
Following routes and going to waypoints.
Transferring Waypoints and Routes
Usingtracks,includingshowingtracks,settinguptracks,savingtracksand
creating a route from a track (SmartRoute).
All these chart functions are available in plotter mode, so you can plot and
track routes at large scales even when a chart card is not installed.
Further functions, including measuring distances and setting alarms are
described in Chapter 4.
Safety
The chartplotter makes it very easy to place a waypoint and travel towards it.
However, you should always check first that the route is safe. If you are using
the chartplotter in combination with a SeaTalk autopilot, the autopilot will
prompt for confirmation before it steers the vessel towards the waypoint.
If you have entered your route using a small-scale chart, zoom in to a larger
scale to check for hazards, such as small shoals, that may not be shown on the
smaller scale charts.
Note: Until you are familiar with interpreting the chart display, you should
take every opportunity to compare the displayed objects with visual targets,
such as buoys and coastal structures. You should practice harbour and coast-
al navigation during daylight and in clear weather conditions.
CAUTION:
The equipment should not be used as a substitute for good navigational
practice nor for official government paper charts.
Download from Www.Somanuals.com. All Manuals Search And Download.
3-2
SL520/530/631 PLUS Chartplotter Displays
3.2 Using Chart Cards
The chartplotter has a built-in world map; most areas are displayed on a scale of
4000 nm from the top to the bottom of the screen, and can be zoomed in to
150 nm.
Tousethechartplotterasanavigationaid,chartswithdetailedinformationforthe
area you wish to navigate are required. The charts are available on C-MAP NT
electronic chart cards (C-Cards), each of which can store as many as 20 charts in
an electronic format. A single C-MAP chart normally provides as much
information as is available in paper charts for that geographic area, and can be
displayed down to a range of 1/64 nm on the screen if the data is available.
Two card slots are provided on the display unit. Chart data from both slots can
be downloaded.
The chart scale in use is indicated in the status bar - the number represents the
distance (in nautical miles) displayed from the top of the chart window to the
bottom of the chart window.
Note: You can remove and insert cards while a chart is displayed. The chart
information is retained on-screen until the chartplotter redraws the screen:
for example, when you pan outside the current area, or use the RANGE key to
change the chart scale.
Inserting a Chart Card
➤ To insert a chart card:
1. Check that the card is a C-MAP NT C-Card with the required chart stored
on it.
2. Open the card cover, at the lower left of the display front panel.
3. Hold the card with the title label towards the left, as shown in the illustra-
tion.
4. Gently push the card into one of the two slots. It will only go in if it is cor-
rectly oriented. Push the card in as far as it will go, then move it to the right
so that the top is under the retaining pegs. The card will be held in place by
the pegs.
5. Close the card cover until it clicks shut, to prevent water entering the dis-
play unit.
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 3: Standard Chart Operations
3-3
D4158-1
Figure 3-1: Removing the Chart Card
Removing a Chart Card
We recommend that before you remove a chart cartridge, you ensure the chart
is not being used on any other display unit. Removing a chart cartridge whilst
a display unit is accessing the chart may cause an operational error.
➤ To remove a chart card:
1. Open the card cover, at the lower left of the display front panel.
2. Press on the card you wish to remove, and move the top of the card to the
left to clear the retaining pegs.
The card will spring half-way out, enabling you to grip the card and
remove it from the slot.
3. Remember to close the card cover so that it clicks shut, to prevent water
from entering the card reader assembly.
Displaying the Chart Data
Thenewchartinformationwillbedisplayedwhenyoumovethecursorintoan
area covered by the new chart or, if it is already in the area, change the range
scale.
The boundary of each chart digitized in the current card is defined by a box or
rectangle. (You can switch off the chartboundaries display if you wish, as part
of the chartplotter set up described in Section 5.4.)
Download from Www.Somanuals.com. All Manuals Search And Download.
3-4
SL520/530/631 PLUS Chartplotter Displays
➤ To zoom in:
1. Usethetrackpadtomovethecursorinsideoneofthechartboxes, andpress
the lower part of the RANGE key.
That area is expanded, with the cursor at the centre, so that you can see
more detail. Note that the smaller the chart box is on the screen, the further
you can zoom in and the greater the amount of detail that is available.
RANGE
If you have switched on Plotter Mode (see Section 5.4), you can zoom in
further than the most detailed chart; all chart functions remain available.
Displaying Chart Object and Source Information
Chart cards include a number of displayed objects for which information is
available, such as lights and buoys. They also contain additional source data
for structures, lines, open sea areas etc. You can use the context-sensitive
cursor to identify (in a pop-up box) an object or chart position and you can
obtain detailed information for the selected item.
Set up options let you specify when an identification pop-up is displayed;
three options are available:
•
Display a pop-up for all objects and source data automatically when the
cursor is over the object symbol or source area.
•
•
Display a pop-up for displayed objects when the cursor is over the symbol.
Do not display the identification pop-ups.
The chartplotter also provides information for the nearest waypoint, port
service, port, tide station, wreck or obstruction for a selected position. If your
chart includes port and tide data, this can be displayed.
➤ To identify an item and obtain detailed information:
1. Move the cursor over the symbol or chart position for which you require
the information. If specified in Chart Set Up, a pop-up box such as the fol-
lowing is displayed at the lower left or upper right corner of the screen:
1 Object
FAIRWAY BN Bn Safe Water RW
LFI.W.10s7m5M
D4260-2
2. Toviewdetailedinformation, pressENTER. Thedetailsavailablearelisted
on-screen in an object information pop-up.
The pop-up is spit into two windows; objects are listed in the upper win-
dow and details for the selected object are provided in the lower win-
dow.Use the trackpad to select an object in the upper window and use the
soft keys to scroll up or down the detailed information in the lower win-
dow.
3. Press CLEAR to remove the pop-up from the screen and return to the
default display.
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 3: Standard Chart Operations
3-5
Port Area
At large chart scales port areainformation is indicated by the symbol . An
objectinformation pop-up provides the nameofthemarina orportanda listof
the facilities available.
Where available, details for each facility can be displayed. This information
includes items such as accommodation, slip sizes, fueling, sanitation,
electrical or other maintenance services provided, VHF channels monitored,
and other safety and navigation information.
In some areas the chart shows symbols for individual facilities. The facilities
and their associated symbols are illustrated in Figure 3-2.
Figure 3-2: Port Symbols
Tide Data
The symbol
indicates tide height data is available for that position on the
chart. When you select the tide height option, a graph of predictions for
maximum and minimum tide heights is displayed, data for sunrise and sunset
is also provided as illustrated Figure 3-3.
Download from Www.Somanuals.com. All Manuals Search And Download.
3-6
SL520/530/631 PLUS Chartplotter Displays
Note: The predictions available are sufficiently accurate under moderate
weatherconditions, forthecoastalareas servedby the reference station, to be
used for navigation planning. However, certain weather fronts and storms
can alter tidal patterns and influence predicted times and heights.
The cursor, represented by a dotted vertical line on the graph, is used to select
a time for which the tide height is displayed.
You can use the soft keys and trackpad to change the date for which tide
information is shown.
CSR 50°49^05W BRG 304°T
POS 001°18^00W RNG 27.70nm
6nm
CALSHOT CASTLE
4.61
3.96
3.31
2.66
2.01
1.36
0.71
0 2 4 6 8 10 12 14 16 18 20 22 24
CURSOR
13:30
HEIGHT 4.06m
SELECTED DATE
2/01/1998
TIME
SUNRISE/SUNSET
HIGH/LOW WATER
TWILIGHT
SUNRISE
SUNSET
0646
0807
1611
1732
LOW 0640 0.88m
HIGH 0220 4.22m
LOW 1900 0.76m
HIGH 1400 4.10m
TWILIGHT
SET DATE PREV. DAY
TODAY
NEXT DAY
D4270-2
Figure 3-3: Tide Data
➤ To select a time, use the trackpad to move the cursor to the required time.
➤ To change the day press PREV. DAY, DAY or TODAY, as required. Alternatively,
pressSETDATE;tochangedate, usethetrackpadtomovethecursorleft/rightto
select the character and up/down to increase/decrease the value.
The graph and tide data will be updated accordingly.
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 3: Standard Chart Operations
3-7
Nearest
You can obtain information for the eight nearest waypoints, port services,
ports, tide stations, wrecks or obstructions for a selected position. The
chartplotter also provides options to redraw the chart with a selected item at
the centre, Goto a waypoint and display a list of all the port on the chart card.
➤ To obtain the information for the nearest objects:
1. Move the cursor to the required position then press ENTER to display the
object information pop-up.
2. Press the NEAREST soft key. The Find Nearest pop-up list is displayed.
Use the trackpad to highlight the required object, then press ENTER.
i. For port services the port service symbols are displayed, use the track-
pad to highlight the required service, then press ENTER.
If you select a port then press ENTER, detailed information for the ser-
vice at that port is displayed. Typical port data is shown in Figure 3-4.
D4255_1
Figure 3-4: Nearest Port - Typical Data
ii. For all other items, the eight nearest objects are listed with distance and
bearing.
Soft keys provide you with options to EXPAND port, wreck and obstruc-
tions data; view a FULL LIST of ports detailed on the chart card; SHOW
TIDE data; GOTO a waypoint and FIND the object (redraw the chart with
the object at the centre). Use the trackpad to highlight an object, then
press the required soft key.
3. To return to the default display, press CLEAR to back-track through the
pop-up lists.
Download from Www.Somanuals.com. All Manuals Search And Download.
3-8
SL520/530/631 PLUS Chartplotter Displays
3.3 Working with Waypoints
Introduction
The Chartplotter enables you to place up to 998 waypoints (in addition,
waypoint number 999 is used for MOB operation): a waypoint is a position
enteredonachartasareference, orasaplacetogoto. Allwaypointsplacedon
the chartplotter are stored in a waypoint database list which includes symbol,
position, bearing, range and additional data. All waypoints in the database are
displayed on the screen, unless you set waypoint display off in the Chart Set
Up menu, as described in Chapter 5. You can select a waypoint, either on-
screen or from the list, for editing.
A waypoint can be placed at the cursor position, or at the vessel’s current
position (this is sometimes known as an event mark); a waypoint at the vessel
position includes additional information (if available) on the depth and
temperature when it was placed. Alternatively, you can manually enter
Waypoints as either Lat/Long coordinates or Loran TDs which are
automatically converted into Lat/Long coordinates. All waypoints can be
included in a route. You can place waypoints, using simulator mode, before
you install the chartplotter on your vessel.
When you place a new waypoint, it is displayed using the default symbol of a
cross (unless you have changed the symbol in Chart Set Up). The waypoint is
added to the waypoint list and tagged with the next available number. You can
use the edit functions to change the symbol and name. When the cursor is
positioned over a waypoint, the waypoint bearing and range are displayed.
Waypoints in the current route are available on other SeaTalk instruments that
supportcurrentroute transfer, forexample, anotherRaymarine Chartplotteror
ST80 Masterview. You can transfer waypoints between the chartplotter and
other NMEA or SeaTalk instruments using the Waypoint Transfer functions.
You can also save waypoints to, or load them from, a user cartridge. These
functions are described in Section 3.6.
This section explains how to perform the following tasks using the on-screen
cursor and the waypoint list:
•
•
•
•
•
•
Placing a Waypoint
Selecting a Waypoint
Displaying Waypoint data
Editing a Waypoint (symbol, name & position)
Erasing a Waypoint
Moving a Waypoint
At the end is a section about using the ST60/80 Navigator Keypad to select,
edit, and name your waypoints.
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 3: Standard Chart Operations
3-9
Placing a Waypoint
The scenario Place and Goto a Waypoint on page 2-18 provides a simple
example of how to place a waypoint.
➤ To access the place waypoint soft keys, press MARKS:
PLACE WPT PLACE WPT WAYPOINT LOAD/SAVE
MARKS
AT CURSOR AT VESSEL LIST
USER CARD
D5572-1
➤ To place a waypoint at the cursor position or at the vessel position:
PLACE WPT
AT CURSOR
1. Press either the PLACE WPT AT CURSOR or the PLACE WPT AT VESSEL soft
key. The waypoint is added to the waypoint list and tagged using the next
available number.
PLACE WPT
AT VESSEL
The waypoint soft keys are displayeduntil youmove thecursor away from
the waypoint or press CLEAR.
GOTO
WAYPOINT WAYPOINT WAYPOINT WAYPOINT
EDIT
ERASE
MOVE
D4163-1
You can use the EDIT WAYPOINT soft key to name the waypoint as
described in Editing Waypoints below.
2. Press CLEAR or ENTER to remove the place waypoint soft keys.
➤ To place a waypoint as latitude/longitude using the Waypoint List:
MARKS
1. PressMA RKS, followedbytheWAYPOINTLISTsoftkey. TheWaypointList
and associated soft keys are displayed.
WAYPOINT
LIST
2. Press the MAKE NEW WAYPOINT soft key followed by the LAT/LONG soft
key;theWPT POSITION (LAT/LONG) screenisdisplayed, withit’sassociated
soft keys. The waypoint is placed at the current vessel position, or if not
available, the cursor position.
MAKE NEW
WAYPOINT
Download from Www.Somanuals.com. All Manuals Search And Download.
3-10
SL520/530/631 PLUS Chartplotter Displays
WAYPOINT LIST
NAME
SYMBOL
WAYPOINT 001
WAYPOINT 002
WAYPOINT 004
WAYPOINT 005
POSITION
50°21^966N
001°20^368W
BRG _186°
RNG _21.0nm
TEMP
DEPTH
---°C
---m
DATE
TIME
--/--/--
--:--:--
GOTO
WAYPOINT WAYPOINT WAYPOINT TRANSFER
EDIT
MAKE NEW WAYPOINT
D4262-2
3. You can use the soft keys to edit the waypoint position as described in Edit-
ing the Waypoint Details on page 3-13.
It is added to the Waypoint List and named with the next available number.
To return to the default soft key display, press ENTER or CLEAR twice.
➤ To place a waypoint as Loran TDs using the Waypoint List:
1. Press MARK, followed by the WAYPOINT LIST soft key; the Waypoint List
and associated soft keys are displayed.
2. Press the MAKE NEW WAYPOINT, the waypoint is placed at the current ves-
sel position, or if not available, the cursor position. To change the position
press theLORAN TDs softkey;the WPT POSITION (LORAN TDs) screen is dis-
played, with it’s associated soft key.
Note:YoucanenterwaypointsasLoranTDswhichareconvertedtoLat/Long
coordinates. However, although the waypoint is shown in both Lat/Long and
LoranTDsintheWaypointList, youcansubsequentlyonlyeditthepositionas
Lat/Long coordinates. TD entries in the Waypoint List are shown only for
those waypoints which were entered as TDs.
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 3: Standard Chart Operations
3-11
WPT POSITION (LORAN TDs)
CHAIN
6731 - NELS Lessay
SLAVES Y - Z (24 -39)
TD 1
29138.0
44713.8
+0.0
TD 2
ASF 1
ASF 2
+0.0
CHAIN
ASF1/ASF2 SET TD 1 SET TD 2
3. Edit the Loran parameters as required, using:
i. The CHAIN soft key, which enables selection of both the Chain and it’s
Slave:
WPT POSITION (LORAN TDs)
CHAIN
6731 - NELS Lessay
SLAVES Y - Z (24 -39)
TD 1
29138.0
44713.8
+0.0
TD 2
ASF 1
ASF 2
+0.0
SELECT CHAIN
SELECT SLAVES
ii. The ASF1/ASF2 soft key, which presents two soft keys for editing ASF 1
and ASF 2 parameters independently:
SET ASF 1 SET ASF 2
iii. TheSET TD 1 and SET TD 2 softkeys, whichenableediting of eachTD’s
parameters independently.
Note: Except for the CHAIN setting, parameters are edited using the trackpad
as described in Editing the Waypoint Details on page 3-13.
4. When editing is complete, press the ENTER key to save the waypoint or
CLEAR to cancel the operation; the display returns to the New Waypoint
screen.
Press the ENTER or CLEAR to return to the Waypoint List.
Download from Www.Somanuals.com. All Manuals Search And Download.
3-12
SL520/530/631 PLUS Chartplotter Displays
Selecting a Waypoint
Positioning the cursor over a waypoint selects that waypoint and accesses the
waypointsoftkeys. ThesekeysenableyoutoGOTO (describedinSection 3.5),
EDIT (symbol, name, position), ERASE or MOVE the waypoint.
Selecting a waypoint from the List allows you to GOTO and EDIT (symbol,
name, position, erase) the waypoint. The Waypoint List also provides options
to make a new waypoint and transfer waypoints.
➤ To select a waypoint using the cursor:
1. Move the cursor over the waypoint, until the letters WPT are displayed.
TheWaypointDatabox(seeWaypointDataDisplayonpage 3-12)andthe
following soft keys are displayed:
WPT
GOTO
WAYPOINT WAYPOINT WAYPOINT WAYPOINT
EDIT
ERASE
MOVE
D4163-1
The selected waypoint can be edited via these soft keys.
➤ To select a waypoint using the Waypoint List:
1. Press MARKS, followed by the WAYPOINT LIST soft key.
The Waypoint List and associated soft keys are displayed.
The list details all waypoints in alpha-numeric order. The selected way-
point is indicated by the selection bar; its position, bearing and range are
provided.
MARKS
WAYPOINT
LIST
2. Usethetrackpadtomove theselectionbarupanddown thelisttohighlight
the required waypoint.
The selected waypoint can be edited via the soft keys displayed.
Waypoint Data Display
Waypoint data can be viewed in two ways: you can use the context-sensitive
cursor to select the waypoint and thus display the waypoint data box, or you
can view waypoint details on the waypoint list.
Note: To permanently display the target waypoint data box, select it in the
System Set Up menu (see Section 5.3) and use the SCREEN soft key to switch
data boxes on.
➤ To display the waypoint data box, move the cursor over the waypoint.
The waypoint data box is displayed, this indicates waypoint number/name,
bearing and range (or latitude and longitude if selected in system set up).
WAYPOINT 001
BRG
RNG
191oT
2.2nm
D4250-1
While the cursor is over the waypoint, the waypoint soft keys are displayed.
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 3: Standard Chart Operations
3-13
➤ To remove the waypoint data box and soft keys either:
Move the cursor away from the waypoint, or press CLEAR.
➤ To display the waypoint details from the waypoint list:
Select the waypoint in the list as described above.
MARKS
The details for the selected waypoint are displayed in the lower half of the
window. Temperature, depth, date and time are included (if available) for
waypoints placed at the vessel position.
WAYPOINT
LIST
To remove the Waypoint List and return to the default soft key display, press
CLEAR twice.
Editing the Waypoint Details
You can change the name, symbol and position of any waypoint.
➤ To edit a waypoint:
1. Select the waypoint, using the cursor or the waypoint list, as previously
described. The waypoint soft keys are displayed.
EDIT
WAYPOINT
2. Press the EDIT WAYPOINT soft key. The Edit Waypoint soft keys are dis-
played:
SYMBOL
NAME
POSITION
D4166-1
3. To edit the symbol, press the SYMBOL soft key.
Use the soft keys, shown in the following illustration, to highlight the
required symbol, then press ENTER to confirm the selection.
Press ENTER or CLEAR to return to the default soft keys.
SELECT SYMBOL
4. To edit the waypoint name, press the NAME softDk41e78-y1 .
The NAME WAYPOINT window is displayed.
Use the trackpad to enter or edit the name:
Use the left or right side of the trackpad to move the cursor to the character
you wish to change.
Use the top or bottom of the trackpad to scroll through the characters.
When you have finished editing the name, to remove the window, press
ENTER to save the name or CLEAR to cancel the operation. The waypoint
name replaces the waypoint number.
Press ENTER or CLEAR to return to the default soft keys.
Download from Www.Somanuals.com. All Manuals Search And Download.
3-14
SL520/530/631 PLUS Chartplotter Displays
5. To edit the waypoint position, press the EDIT WAYPOINT soft key, followed
EDIT
WAYPOINT
Use the soft keys to select LAT, LON, BRG or RNG.
Use the trackpad to edit the value:
Use the left or right side of the trackpad to move the cursor to the character
you wish to change.
Use the top or bottom of the trackpad to scroll through the characters.
Adjust each parameter until the waypoint position is correct.
Whenyouhavefinishededitingtheposition, pressENTERto save the position
or CLEAR to cancel the operation. Press ENTER or CLEAR again, the
keys are displayed.
Erasing a Waypoint
You cannot erase the target waypoint or waypoints that are used in routes.
However, you can remove a waypoint from the current route - see Editing a
Route on page 3-27.
If you try to erase a waypoint that is used in a saved route you are warned
“WAYPOINT IS USED IN A ROUTE & CANNOT BE DELETED”
➤ To delete a waypoint using the cursor:
1. Movethecursoroverthewaypoint, until theletters WPTare displayed. The
WPT
waypoint soft keys are displayed.
ERASE
WAYPOINT
2. Press the ERASE WAYPOINT soft key. The waypoint is removed from the
screen and the Waypoint List is updated.
Note: If you have stopped a GOTO (see Stop Follow or Stop Goto on
page 3-33), thetargetwaypointremainsdisplayedasatarget;youneedtouse
the CLEAR GOTO soft key before you can erase the waypoint using the cursor.
➤ To delete a waypoint using the waypoint list:
1. Select the waypoint from the waypoint list as previously described. The
waypoint list soft keys are displayed.
MARKS
WAYPOINT
LIST
2. Press theEDITWAYPOINT soft key, followed by ERASE WAYPOINT. Theway-
point is removed from the screen and the waypoint list is updated.
Moving a Waypoint
You can move any waypoint except the target waypoint (the waypoint you are
following). You can use the Waypoint soft keys and cursor to move the
selected waypoint, or you can edit the waypoint position.
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 3: Standard Chart Operations
3-15
CAUTION:
Take care when editing waypoints as it is possible to move waypoints that
are used in routes stored in the Route Database. In such instances, the
stored route will include the waypoint in its new position.List.
➤ To move a waypoint using the cursor:
1. Movethecursoroverthewaypoint, until theletters WPTare displayed. The
WPT
waypoint soft keys are displayed.
MOVE
WAYPOINT
2. Press MOVE WAYPOINT, the cursor changes to a four-headed arrow.
3. Move the cursor to the required waypoint position.
Press ENTER to set the position and return to normal cursor control.
Press CLEAR to cancel the operation.
➤ To move a waypoint using the Waypoint Edit functions:
1. Selectthewaypointusingeitherthecursororthewaypointlistasdescribed
above. The waypoint soft keys are displayed.
2. To edit the waypoint position proceed as previously described in Editing
the Waypoint Details on page 3-13.
Using the ST60 or ST80 Navigator Keypad
If you have an ST60 or ST80 Navigator Keypad connected on SeaTalk it can
be used to name or edit your waypoints, tracks, or routes on any display in the
system. ThekeypadcanalsobeusedtoselectentriesintheWaypointList. The
Navigatorprovides10dedicatedalphanumerickeys,amultidirectionalcursor
control pad, plus Insert and Delete keys. The snall red LED glows when the
keypad is operational.
Note: When using the Navigator Keypad, you should be aware that it can con-
trol several displays simultaneously; any display in edit mode (i.e. ready for
alpha-numeric data entry) will be affected by the Navigator Keypad.
1
abc
2
def
3
ghi
4
jkl
5
mn
6
opq
7
rst
8
uvw
9
xyz
ins
0
del
NAVIGATOR
D1934-2
Figure 3-5: ST80 Navigator Keypad
Download from Www.Somanuals.com. All Manuals Search And Download.
3-16
SL520/530/631 PLUS Chartplotter Displays
Most of the alphanumeric keys are used to input multiple characters. Each
timeyoupressoneofthesekeysinsuccession, thenextcharacteronthatkeyis
input. For example, each press of the 1 key alternately inputs A, B, C, then 1.
A short beep is emitted each time a key is pressed.
The Navigator’s arrow keys function much like the chart display’s trackpad,
enabling you to move the cursor position or input alpha, numeric, or special
characters (. , - / ‘ & ).
The ins key functions the same as the ENTER key on chart display and del
inserts a space during edit mode.
Selecting an Entry in the Waypoint List
TheNavigatorcanbeusedto selectanexistingiteminthe WaypointList. This
can be accomplished using the arrow or alphanumeric keys.
➤
To select an existing item in the Waypoint List:
1. Use the up and down arrow keys to move the selection barup and down the
list to highlight the desired entry.
or
Press the alphanumeric key that contains the first letter or number of the
desired waypoint name. The selection bar moves to the entry starting with
that letter or number.
If more than one entry begins with that character, the selection bar moves
to the first one in the list. Each time the same key is pressed, the selection
bar moves to the entry starting with the next character on the key. If no
entry exists for that character, the entry starting with the nearest previous
character is selected. If the numeric value of the key is input when no
numeric entry exists, the selection bar moves to the first alpha entry.
For example, let’s say we have four waypoints named ORION,
POLARIS, QUANTUM, and 6-GUN. Pressing the opq/6 key four suc-
cessive times would select the waypoints ORION (O), POLARIS (P),
QUANTUM (Q), then 6-GUN (6). However, pressing the rst/7 key four
successive times would select QUANTUM for the first three key presses
because entries beginning with the associated letters do not exist and Q is
the next previous beginning letter. The fourth press of the rst/7 key would
select 6-GUN because no entries begin with a 7 and 6 is the next previous
beginning number.
2. Use the ins key like the display’s ENTER key, to close the Waypoint List.
The del key and left and right arrow keys do not function in select mode.
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 3: Standard Chart Operations
3-17
Editing Entries in the Waypoint, Route, or Track Lists
You can also use the Navigator Keypad to edit an existing item or to name a
new item in the Waypoint List, Route List, or Track List. You first must enter
the edit mode for the list you want to modify. Methods for editing each list are
described in the respective sections of this chapter.
➤
To edit an item in a list using the Navigator Keypad:
1. If necessary, use the right and left arrow keys to move the cursor to the
desired character position.
2. Press an alphanumeric key until the desired character is displayed. Each
time you press one of these keys in succession, the next character on that
key is input.
or
1. Usetheupanddownarrowkeystoscrollthroughthelistofalpha,numeric,
and special characters until the desired character is displayed (just as you
would with the trackpad). Note that you must use this method to input spe-
cial characters; they are not available using the alphanumeric keys.
Use the del key to insert a space, if required.
2. Use the arrow keys and alphanumeric keys to input the remainder of the
characters required to complete the editing.
3. When done, press the ins key to enter your changes.
Download from Www.Somanuals.com. All Manuals Search And Download.
3-18
SL520/530/631 PLUS Chartplotter Displays
3.4 Working with Routes
A route is made up of a series of waypoints (maximum 50). To make a route
you place a series of waypoints on the chart, or you can select waypoints from
the Waypoint List. You can also save your vessel’s track as you navigate, then
convert the track to a route - this function is described in Section 3.7.
When a route is created it becomes the current route and is displayed on-
screen. The current route is maintained when you power-off. Only one route
can be current and is displayed (if it is in the field-of-view) as solid lines
connecting waypoints. If you are following the route, the current leg is shown
as a dotted line and previous legs are removed from the screen (although the
waypoints remain displayed). The current route (and its waypoints) is
transferred via SeaTalk to a repeater chart display and other instruments. You
can alsousethe WaypointTransferfunctionstotransferthe route databasetoa
repeater display.
Once you have created a route you can use the GOTO soft keys to follow the
route. In addition, the GOTO default soft key provides various options as
described in Section 3.5.
Up to 20 routes can be saved in the route database. You can then select a route
from the database list as the current route.
The current route can be edited by adding and moving waypoints. The current
routeisalwaysplacedinthedatabaselistasroutenumber0,soyoucaneditthe
current route without affecting the original route in the database. Once a route
has been saved, options are also provided to name a route, erase a route and to
display route details.
Youcanusetherouteinformationtoreviewyourpassageplanbyadjustingthe
planned Speed Over Ground (SOG).
Note:
It is possible for the current route to be overwritten by a route from another
unit on an integrated system, so it is advisable to save all routes.
This section explains how to perform the following tasks:
•
•
•
•
•
Creating a new route.
Saving the current route in the database list.
Clearing the current route.
Retrieving a route from the database list as the current route.
Displaying route information, including the route leg data and waypoint
details. Use the waypoint details to review your passage plans for different
speeds.
•
•
Using the database list to erase and name existing routes.
Editing a route by adding, removing and moving waypoints.
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 3: Standard Chart Operations
3-19
➤ To access the route soft keys, press the default soft key ROUTE:
ROUTE
MAKE
ROUTE
EDIT
ROUTE
CLEAR
ROUTE
MORE¬
D4167-1A
Creating a New Route
Note: If there is a current route, it is cleared when you select MAKE ROUTE. If
you are following the current route you are prompted to STOP FOLLOW. Press
the YES soft key to continue, or NO to abandon route creation. If the route has
not been saved you are prompted to save it.
The chart scenario Make and Follow a Route on page 2-20 provides a simple
example of how to create a route.
There are two methods to create routes, whilst creating a route you can switch
between these methods:
•
•
Placing new waypoints on the chart.
Selecting existing waypoints from the Waypoint List.
You can edit a route after you have finished making it, as described in Editing
a Route on page 3-27.
➤ To make a new route by placing waypoints:
Note: You can pan the chart and change the scale while placing waypoints.
1. If necessary, move the cursor to the area in which you wish to make the
route, and select a suitable chart scale.
2. Press the ROUTE soft key, then press the MAKE ROUTE soft key. The make
ROUTE
route soft keys are displayed:
MAKE
ROUTE
PLACE UNDO
WAYPOINT WAYPOINT
ACCEPT
ROUTE
USE
WPT LIST
3. Move the cursor to the position on the chartwhereyou want your first way-
point to be. Press the PLACE WAYPOINT soft key.
PLACE
WAYPOINT
Note: You can position the cursor on an existing waypoint – the cursor text
WPT indicates you are re-using the waypoint rather than placing a new one.
This waypoint is included in the route when you press PLACE WAYPOINT.
The waypoint appears on the screen at the cursor position. The number
displayed alongside the waypoint identifies its position in the route. The
new waypoint is temporarily added to the waypoint list with the first avail-
able waypoint number. The waypoints in the current route are re-num-
bered to identify the new positions.
Download from Www.Somanuals.com. All Manuals Search And Download.
3-20
SL520/530/631 PLUS Chartplotter Displays
Note: If you Clear the route before it is Saved, the waypoint is removed.
4. Move the cursor to the next waypoint position. A dotted line connects the
cursor to the last placed waypoint.
5. Press PLACE WAYPOINT again. The waypoint is placed and the dotted line
PLACE
WAYPOINT
changes to a solid line.
If you placed the waypoint incorrectly, you can delete the last-placed way-
point by pressing the UNDO WAYPOINT soft key.
UNDO
WAYPOINT
6. Repeat steps 4 and 5 until you have placed all your waypoints. You can
have up to 50 waypoints in a route.
7. When you have entered all your waypoints, either:
Press the ACCEPT ROUTE soft key (or ENTER) to complete the route. Your
ACCEPT
ROUTE
route is displayed on the screen, and is the current route, but it is not active.
The first waypoint of a new route is outlined with a square, indicating that
it will be the target waypoint when the route is activated. If selected, the
waypoint data box is displayed for the target waypoint.
You can save the route as described below.
Note: The completed route is stored in the display unit, and will be re-dis-
played if you turn the unit off and on again. However, on an integrated system
it is possible for a current route from another unit to overwrite this route; it is
therefore recommended that you Save the route as described below.
➤ To make a new route using the Waypoint List:
1. Press the ROUTE soft key; the route soft keys are displayed.
MAKE
ROUTE
EDIT
ROUTE
CLEAR
ROUTE
MORE¬
D4167-1A
2. Press the MAKE ROUTE soft key; the make route soft keys are displayed.
PLACE UNDO
WAYPOINT WAYPOINT
ACCEPT
ROUTE
USE
WPT LIST
3. Press the USE WPT LIST soft key; the MAKE ROUTE screen is displayed with
its associated soft keys.
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 3: Standard Chart Operations
3-21
MAKE ROUTE
NEW ROUTE
WAYPOINTS
COWES
01 HARBOUR
GURNARD LEDGE
MAIN CHANNEL
NEEDLES FAIRWAY
PORT SOLENT
02 MAIN CHANNEL
03 COWES
04 LYMINGTON
50°50^000N
001°06^000W
50°52^230N
001°02^390W
348°m 2.30nm
300°m 1.00nm
INSERT REMOVE
WAYPOINT WAYPOINT
ACCEPT
ROUTE
USE
CURSOR
TheavailableWaypointsarelistedinthelefthandcolumn(alphanumeric);the
right hand column lists the waypoints in the New Route, the number indicates
its order in the route. The lower part of the table shows position, bearing and
range of the highlighted waypoint.
You use the trackpad left/right to move control between the two columns (the
highlighted title indicates the selected column) and the trackpad up/down to
scroll through the lists.
4. Select a waypoint from the Waypoint List then go to the New Route col-
umn and select a position in the list.
selected position in the Route. You can have up to 50 waypoints in a route.
6. To remove a waypoint from the New Route column, highlight the way-
point and press the REMOVE WAYPOINT soft key.
Notes:(1)Awaypointcannotbeusedmorethanonceinaroute;thosealready
used are displayed in a lighter shade of gray.
Notes:(2)The INSERT WAYPOINTorREMOVE WAYPOINTactionadds/removes
the highlighted waypoint to/from the Route column, regardless of which col-
umn is selected.
7. When all waypoints have been entered, press the ACCEPT ROUTE soft key
(or ENTER) to complete the route.
Note: The completed route is stored in the display unit and will be re-dis-
playedifyouturntheunit off thenon again. However, onan integrated system
it is possible for a current route from another unit to overwrite this route; it is
therefore recommended that you save the route, as described in Saving the
Current Route on page 3-22.
Download from Www.Somanuals.com. All Manuals Search And Download.
3-22
SL520/530/631 PLUS Chartplotter Displays
Saving the Current Route
You can save up to 20 named routes in the route databaselist. These routes can
then be re-displayed and followed at a later date. When you save the route, all
new waypoints are saved in the Waypoint List.
Note: If the current route has not been saved, when you attempt an operation
that affects this route, e.g. CLEAR ROUTE, you are prompted to save it.
➤ To save and name the current route:
1. To access the SAVE ROUTE soft key, press the ROUTE soft key, followed by
ROUTE
MORE.
SAVE
ROUTE
2. PresstheSAVEROUTE softkey. Thesaveroutepop-upandtheNAMEROUTE
soft keys are displayed as illustrated in Figure 3-6.
3. The next available entry on the route list is highlighted.
(If required, you can use the trackpad to select another position in the list;
this can be a blank slot, or an existing route that you no longer require).
SAVE ROUTE
1
2
3
4
5
EMPTY
EMPTY
EMPTY
EMPTY
EMPTY
NAME ROUTE?
YES NO
D4155-1
Figure 3-6: Save Route Window
4. If you do not wish to name or re-name the route, press the NO soft key to
clear the list. The route is saved and is listed as Route Not Named.
If you wish to name the route press the YES soft key. Use the trackpad to
move the cursor right or left to the character you wish to edit. Then use the
top or bottom of the trackpad to increase or decrease the letter or number.
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 3: Standard Chart Operations
3-23
You can use a Navigator Keypad (see Using the ST60 or ST80 Navigator
Keypad on page 3-15) to name the route.
5. Press ENTER to finish and clear the Name List, or press CLEAR to cancel
the operation. To return to the default soft key display, press ENTER again.
Clearing the Current Route
if the current route has not been saved, you have the option of saving it and, if
you are following the current route, you have the option to stop.
➤ To clear the current route:
1. Press the ROUTE default soft key or place the cursor over a route leg until
the text RTE is displayed.
ROUTE
Press the CLEAR ROUTE soft key.
RTE
2. If you are following the current route the STOP FOLLOW soft keys are dis-
played.
STOP
FOLLOW
To cancel the CLEAR operation press NO.
To stop following and clear the route press YES.
SAVE
ROUTE
3. If the route has not been saved the SAVE ROUTE soft keys are displayed.
To clear the route, without saving it in the route database, press NO.
To save the route in the database, press YES. The Name route soft keys are
displayed and you should continue as described in the previous section,
Saving the Current Route on page 3-22.
The current route is cleared from the screen and the default soft keys are
displayed. You can now use the ROUTE soft keys to make a route, or to show
another route from the database.
Retrieve a Route From the Database
You can select a route as the current route from the database list. The list is
accessed from the second set of ROUTE soft keys.
➤ To select a route as the current route:
1. Press the ROUTE soft key, followed by MORE, then press ROUTE LIST. The
ROUTE
route list is displayed as illustrated in Figure 3-7. The selection bar indi-
cates the selected route.
SHOW
ROUTE
2. Use the trackpad to select the required route then press the SHOW ROUTE
soft key. The chart is re-drawn at a scale suitable to display thewhole route.
Download from Www.Somanuals.com. All Manuals Search And Download.
3-24
SL520/530/631 PLUS Chartplotter Displays
ROUTE LIST
CURRENT
EMPTY
EMPTY
EMPTY
EMPTY
1
2
3
4
SHOW
ROUTE
ERASE
ROUTE
ROUTE
INFO
NAME
ROUTE
D4263-1
Figure 3-7: Route List Window
Displaying Route Information
You can display the following information that relates to your route:
•
•
Route leg or waypoint information, using the context-sensitive cursor.
Details of waypoints in the route, using the soft keys. You can use this
information to review your passage plan.
Route Leg and Waypoint Information
➤ To display information about aroute leg, movethecursorovertheleguntilthe
letters RTE are displayed. A Route Leg data box such as the following is
displayed.
RTE
ROUTE NO.
ROUTE NAME
LEG 02 - 03
0°T
5.5nm
D4259-2
To remove the data box, move the cursor away from the route or press CLEAR.
➤ To display information about a route waypoint, move the cursor over the
waypoint until the letters WPT are displayed. The waypoint data box is
displayed, this box includes the route and waypoint number.
WPT
To remove the data box, move the cursor away from the route or press CLEAR.
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 3: Standard Chart Operations
3-25
Using Route Information to Review Your Passage Plan
Youcanviewdataforallthewaypointsinthecurrentroute, oranysavedroute.
Youselecttheroute fromthedatabase listand theinformationisdisplayedina
Route Information pop-up; the following details are provided for each
waypoint:
Position
Bearing (from previous waypoint)
Length of leg (from previous waypoint)
Total Length
Time (ETA or Elapsed)
Soft keys are provided to toggle the time between ETA or elapsed and to
change the Speed Over Ground (SOG) value; the ETA for each waypoint is
calculatedusingtheselectedSOG, soyoucanchangetheSOGtodetermineits
effect on your ETA.
The chartscenario Review Your Passage Plan on page 2-22 provides a simple
example of how to use the route information.
➤ To display information about any route in the database:
1. Press the ROUTE soft key, followed by MORE, then press ROUTE LIST. The
ROUTE
route list is displayed. The selection bar indicates the selected route.
2. Usethetrackpadtoselecttherequiredroute,thenpresstheROUTEINFO soft
key.
ROUTE
INFO
The Route Information pop-up is displayed. As illustrated in Figure 3-8,
this lists the waypoints in the route and details bearing, length of each leg,
total distance, and either the estimated time of arrival (ETA) or the elapsed
time.
The soft keys allow you to toggle between ETA or total (elapsed) time,
and to change the Speed Over Ground (SOG) value used in the time calcu-
lations. The current selections are highlighted.
➤ To change the SOG used for ETA calculations:
1. Press one of the PLANNED SOG keys to switch from actual to planned SOG.
2. PresstheupordownPLANNEDSOGkeystochangetheplannedSOGvalue.
The Time values in the Route Information list are updated.
3. Press the ACTUAL SOG key to use the actual SOG value rather than a
planned one.
Download from Www.Somanuals.com. All Manuals Search And Download.
3-26
SL520/530/631 PLUS Chartplotter Displays
INFO FOR ROUTE-CURRENT ROUTE
WPT POSITION BRG DISTANCE TOTAL TIME
°T nm nm ETA
01 50°21^97N --- 0.0
001°15^80W
0.0 --:--
4.4 --:--
10.0 --:--
02 50°21^97N 090 4.4
001°08^75W
03 50°27^48N 000 5.5
001°08^75W
ACTUAL
SOG
1.0kn
TIME
ETA TOTAL
PLANNED SOG
0.0kn
D4264-1
Figure 3-8: Route Information Window
4. Press ENTER to remove the Route Information window, then ENTER or
CLEAR to return to the route soft keys.
5. To return to the default soft key display, press ENTER.
Using the Route List to Erase and Name a Route
You can delete a route and you can re-name a route by selecting the route on
the route list.
➤ To select a route to delete or re-name:
1. Press the ROUTE soft key, followed by MORE, then press ROUTE LIST. The
ROUTE
route list is displayed. The selection bar indicates the selected route.
Press the appropriate soft key – ERASE ROUTE or NAME ROUTE.
2. If you ERASE a route you are prompted to confirm.
Press NO to cancel the operation, then ENTER or CLEAR if you wish to
remove the route list.
ERASE
ROUTE
Press YES to erase the route from the list, then ENTER or CLEAR to remove
the route list.
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 3: Standard Chart Operations
3-27
character you wish to edit. Then use the top or bottom of the trackpad to
increase or decrease the letter or number.
NAME
ROUTE
4. Press ENTER to clear the Name List, or CLEAR to cancel the name then to
return to the default soft key display, press ENTER again.
Editing a Route
Once you have created a route, you can edit it using the Waypoint List as
described in Creating a New Route on page 3-19, or using the context-
sensitive cursor to:
•
•
•
•
•
Insert a Waypoint into the route
Add waypoints at the end of the route
Remove a Waypoint
Reverse a Route
Move a Waypoint as described in Moving a Waypoint on page 3-14.
Any changes you make to the route, except move a waypoint, affect only the
current route. The current route is always held in position 0 in the database, so
you need to Save the route if you want to keep the changes.
Inserting a Waypoint into a Route
Youcan usethecontext-sensitivecursorto insertoneormore waypointsinthe
current route. However, if the route is being followed you cannot insert a
waypoint into the current leg.
➤ To insert a new waypoint in the current route:
1. Move the cursor over the route leg into which you wish to insert a way-
point. The letters RTE and the route leg data box are displayed. The Route
soft keys are displayed.
RTE
2. Press ENTER. The cursor changes to a four-way arrow, controlling a new
waypoint. The waypoint is connected to the existing waypoints on either
side with a dashed line.
3. Move the new waypoint to the required position, and press ENTER to drop
it and return to normal cursor operation, or CLEAR to abandon the opera-
tion.
The new waypoint is temporarily added to the waypoint list and named with
the first available waypoint number. The waypoints in the current route are re-
numbered to identify the new positions.
Note: If you Clear the route before it is Saved, the new waypoint is removed.
Download from Www.Somanuals.com. All Manuals Search And Download.
3-28
SL520/530/631 PLUS Chartplotter Displays
Adding Waypoints at the End of the Route
➤ To add waypoints at the end of the route:
1. Press the ROUTE soft key, followed by the EDIT ROUTE soft key.
The Make Route soft keys are displayed and the cursor is connected to the
last-placed waypoint with a dotted line. You can add further waypoints to
the route in the same way as for a new route.
ROUTE
EDIT
ROUTE
2. Either:
PLACE
WAYPOINT
i. Move the cursor to the required location, and press PLACE WAYPOINT
soft key.
If you place the waypoint in the wrong position, press the UNDO WAY-
POINT soft key.
UNDO
WAYPOINT
Or
ii. Press USE WPT LIST, the MAKE ROUTE pop-up is displayed.
Select a waypoint from the Waypoint List then press the INSERT WAY-
POINT soft key to place the waypoint at the end of the Route.
3. Placeasmanywaypointsasrequired,andpresstheACCEPTROUTEsoftkey,
ACCEPT
ROUTE
the default soft keys are displayed.
Note: You can UNDO waypoints in the original route, not just the new ones.
Removing a Waypoint from the Route
➤ To remove a waypoint from the current route:
1. Move the cursor over the required waypoint until the letters WPT are dis-
WPT
played. The waypoint soft keys are displayed.
2. Press the REMOVE WAYPOINT soft key. The waypoint is removed from the
REMOVE
WAYPOINT
route and the route is re-numbered.
Alternatively, you can remove the last waypoint from a route by pressing the
UNDO WAYPOINT soft key, as described above inAdding Waypoints at the End
of the Route on page 3-28.
If the route has not been saved and the waypoint was placed as part of the
route, the waypoint is erased.
If the route has been saved, or the waypoint existed before you created the
route, the waypoint remains on the screen.
Reversing the Route
➤ To reverse the route, so you can Follow the route back:
1. Either press the ROUTE soft key followed by MORE,
or move the cursor over the required waypoint until the letters RTE are dis-
played.
ROUTE
The route soft keys are displayed.
REVERSE
ROUTE
2. Press the REVERSE ROUTE soft key. The current route is reversed on the
screen.
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 3: Standard Chart Operations
3-29
3.5 Following Routes and Going to Points
The default soft key GOTO accesses the functions to FOLLOW a route and GOTO
a waypoint or cursor. When you select the target destination, the chartplotter
calculates bearing, distance and cross track error; this information is passed to
a helmsman or autopilot. You can also restart the cross track error (XTE) from
the actual vessel position to set XTE to zero at that point.
ROUTE
GOTO
SCREEN FIND SHIP
D4160-1
When the chartplotter is following a route, the target destination is indicated
byasquarearoundthewaypoint(orcursormarker)andadottedlineshowsthe
intended track, from your start point or previous waypoint, to the target
waypoint.
This section describes the following:
•
•
•
Follow a route either forwards, or in reverse order.
Target Point Arrival
Other follow route options, including joining at a selected waypoint,
advancing waypoints, and restarting XTE.
•
•
Go to an individual point, either an existing waypoint or the cursor.
Stop and Restart Follow/Goto.
An alarm is triggered when you approach a waypoint, this section describes
what happens when you arrive at waypoints. Chapter 4 describes how to set
the alarm.
The chartplotter can also display the vessel’s actual track and the track can be
recorded for later display. The Track function is described in the Section 3.7.
➤ To access the Goto/Follow soft keys, press the default soft key GOTO (the soft
keys differ if a follow or goto is already in progress):
GOTO
GOTO
WAYPOINT
GOTO
CURSOR
FOLLOW
ROUTE
D4171-1
Follow a Route
Note: The current route may have been created on this display, or created on
another unit and received on this display via SeaTalk.
If a route has been reversed or if a route on screen was being followed but
stopped before completion, the target waypoint – outlined by a square box –
may be different to when the route was created.
Download from Www.Somanuals.com. All Manuals Search And Download.
3-30
SL520/530/631 PLUS Chartplotter Displays
You should always check the target waypoint before initiating a follow
route.
➤ To follow the current route:
GOTO
1. Press the GOTO default soft key. The Goto/Follow soft keys are displayed.
2. Press the FOLLOW ROUTE soft key.
FOLLOW
ROUTE
Alternatively, to follow a route:
1. Place the cursor over a route leg until the letters RTE and the route soft keys
RTE
are displayed then press FOLLOW ROUTE.
FOLLOW
ROUTE
Your vessel’s current position becomes the origin, and the target waypoint in
the current route becomes the active target.
The soft keys change as follows:
STOP
FOLLOW
EDIT
ROUTE
CLEAR
ROUTE
REVERSE
ROUTE
D4251_1
These options are described in the following sections.
➤ To follow the current route in reverse:
1. Press the ROUTE default soft key, followed by MORE. The route soft keys
ROUTE
are displayed.
REVERSE
ROUTE
2. Press the REVERSE ROUTE soft key. The current route is reversed on the
screen. Press ENTER or CLEAR.
3. Press the GOTO default soft key. The Goto/Follow soft keys are displayed.
GOTO
4. Press the FOLLOW ROUTE soft key.
FOLLOW
ROUTE
The soft keys change as follows:
STOP
FOLLOW
GOTO
CURSOR
RESTART WAYPOINT
XTE ADVANCE
D4172-1
These options are described in the following sections.
Alternatively:
RTE
1. Place the cursor over the route leg until the letters RTE and the route soft
REVERSE
ROUTE
keys are displayed. Press REVERSE ROUTE then FOLLOW ROUTE.
Your vessel’s current position becomes the origin, and the target waypoint in
the current route becomes the active target.
FOLLOW
ROUTE
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 3: Standard Chart Operations
3-31
Target Point Arrival
The arrival alarm is used to alert you when the vessel is approaching the target
point. The arrivalalarmisdefined as acircle (not visibleon the screen) around
the target. You can specify radius of the arrival alarm (see Section 4.3).
The alarm is triggered when either of the following conditions is met:
•
The distance to the target point is less than that specified for the arrival
alarm.
•
Yourvesselreaches theclosestpointofapproachtothetarget(defined by a
line passing through the waypoint and perpendicular to the route leg).
➤ To cancel the arrival alarm and go towards the next waypoint in the route,
either
or
press any key
wait for 10 seconds.
Thetargetbecomestheorigin,thenextwaypointbecomesthetargetpoint, and
the two are connected by a dotted line indicating the current leg. Any previous
route leg is removed from the screen, but waypoints remain.
Note: Whenfollowing a routeusing a SeaTalk autopilot, theautopilot willnot
turn to the new waypoint until it is accepted at the autopilot control unit.
Other Follow Route Options
You can use the soft keys to follow a route from a selected waypoint (join a
route), or if already following, you can advance to the next waypoint. You can
also restart the cross track error, setting the current vessel position as the new
origin.
In addition, you can move a selected waypoint as described in Section 3.3, or
remove a waypoint from the route as described in Section 3.4.
Joining a Route
➤ To start tracking the current route at a selected waypoint:
1. Move the cursor over the required waypoint until the letters WPT and the
WPT
waypoint soft keys are displayed.
2. Press the FOLLOW FROM HERE soft key.
FOLLOW
FROM HERE
Your vessel follows the route, using the selected waypoint as the target
point.
3. Toreturntothedefaultdisplay,movethecursorawayfromthewaypointor
press CLEAR or ENTER.
Download from Www.Somanuals.com. All Manuals Search And Download.
3-32
SL520/530/631 PLUS Chartplotter Displays
Advancing to a Waypoint
➤ Once you are following a route, you can advance to the next waypoint, even if
you have not reached the current target waypoint:
1. If necessary, press the GOTO default soft key to display the Goto/Follow
GOTO
soft keys.
STOP
FOLLOW
GOTO
CURSOR
RESTART WAYPOINT
XTE ADVANCE
D4172-1
2. PresstheWAYPOINTADVANCEsoftkey. Thecurrentlegoftherouteisaban-
doned and the next waypoint becomes the target. The display is updated to
show the new route leg.
WAYPOINT
ADVANCE
Restart Cross Track Error (XTE)
While you are following a route, or going to a target point, you can restart the
XTE. This sets the XTE to zero and moves the origin to the actual vessel
position.
Restarting XTE is useful if you find yourself off track and want to go straight
to your target, rather than get back onto the original track.
➤ To restart XTE:
1. Press the GOTO default soft key, the Follow/Goto soft keys are displayed.
GOTO
RESTART
XTE
position, thus the XTE becomes zero.
Going To an Individual Target Point
Rather than following a route, you can go directly to a selected target point,
this can be an existing waypoint (not in the current route), or the cursor
position.
➤ To navigate directly to an existing waypoint:
1. Usethetrackpad toposition thecursorovertherequired waypointuntilthe
letters WPT and the waypoint soft keys are displayed.
WPT
GOTO
WAYPOINT WAYPOINT WAYPOINT WAYPOINT
EDIT
ERASE
MOVE
D4163-1
Alternatively, you can select the waypoint from the waypoint list as described
in Section 3.3.
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 3: Standard Chart Operations
3-33
2. Press the GOTO WAYPOINT soft key.
GOTO
WAYPOINT
Navigation to the selected waypoint begins. The soft key STOP GOTO is dis-
played.
3. To return to the default soft key display, move the cursor away from the
waypoint or press ENTER or CLEAR.
➤ To navigate directly to the cursor position:
1. Use the trackpad to position the cursor as required.
2. Press the GOTO default soft key, followed by GOTO CURSOR.
If navigation is currently in progress you are warned “Already following
route. Cancel route and goto cursor?”.
GOTO
GOTO
CURSOR
To cancel the GOTO CURSOR operation, press NO.
To continue with the GOTO CURSOR operation (and stop the current GOTO
ROUTE), press YES.
The chartplotter places a temporary waypoint as the target and starts to
navigate towards it. The waypoint is shown as a square with a circle and
dot in the centre, and is connected to the vessel’s starting position with a
dashed line.
STOP
GOTO
The soft key STOP GOTO is displayed.
3. To return to the default soft key display, move the cursor away from the
waypoint or press ENTER or CLEAR.
Stop Follow or Stop Goto
➤ To stop following the route or target point
either:
1. If necessary, press the GOTO soft key, then press the STOP GOTO/FOLLOW
GOTO
soft key.
STOP
GOTO
Or:
1. Move the cursor over any waypoint or leg in the current route, then press
STOP
FOLLOW
the STOP GOTO/FOLLOW soft key.
The dotted line from your vessel to the target waypoint disappears.
If you stopped a GOTO WAYPOINT or CURSOR, to remove the target point from
the screen, move the cursor over the target point then press the CLEAR GOTO
soft key.
If you subsequently use the FOLLOW ROUTE soft key to restart navigation, the
route is followed from the point at which it was stopped. This is indicated by a
square around the target waypoint. If you want to follow from another
waypoint you can initiate the follow then use the WAYPOINT ADVANCE or
FOLLOW FROM HERE soft key to step through the route.
Download from Www.Somanuals.com. All Manuals Search And Download.
3-34
SL520/530/631 PLUS Chartplotter Displays
3.6 Transferring Waypoints and Routes
Displayed SeaTalk Waypoints
In an integrated system, when a route is made current on any SeaTalk
equipmentit is sent to all SeaTalk instruments, including this chartplotter; this
route will override any other current route. When GOTO waypoint or GOTO
cursor is in operation it is considered a route.
The current route can be edited on any instrument with route edit capability.
Note: Transferred waypoints are not automatically saved by the chartplotter,
however you can save the route locally, thus adding the waypoints to the local
waypoint list.
Managing Database Lists
There are several methods of maintaining database lists. The method you
choose will depend on the links available (SeaTalk or NMEA), and whether
you want to transfer individual waypoints or the complete waypoint and route
list:
•
•
•
You can save the complete Waypoint and Route Lists to a user cartridge in
the chart card slot.
You can load new Waypoint and Route Lists from a user cartridge in the
chart card slot.
If waypoints are transmitted by other equipment on SeaTalk or NMEA,
you can receive them on the chartplotter.
When RECEIVE WPTS FROM ST/NMEA is selected, any waypoints sent on
SeaTalk or NMEA are transferred and appended, one-by-one, to the way-
point list; routes sent on NMEA are appended to the route list.
You can use this function to add waypoints from a PC connected via
NMEA.
•
You can send the waypoint and route lists from the chartplotter to other
instruments via NMEA using the SEND WPT LIST function.
Sending the waypoint list does not affect current routes.
The NMEA link could be to a PC.
CAUTION:
The function LOAD USER CARD replaces the existing waypoint and route
lists with the transferred lists.
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 3: Standard Chart Operations
3-35
➤ To save waypoints to, or load waypoints from a user cartridge:
CAUTION:
Loading waypoints from a user cartridge overwrites any existing
waypoint and route lists.
1. Insert a C-MAP User Card into the lower of the two cartridge slots.
1. Press MARK S followed by the LOAD/SAVE USER CARD soft key.
2. The User Card Menu and associated soft keys are displayed.
3. Press the SAVE WPT/RTE DATA TO CARD or LOAD WPT/RTE DATA FROM
MARKS
CARD soft key; an appropriate warning and Yes/No soft keys are displayed.
USER CARD MENU
USER CARD PRESENT
WARNING
SAVING DATA TO THE USER
CARD WILL ERASE ALL EXISTING
WAYPOINT AND ROUTE DATA
ON THE CARD.
ARE YOU SURE ?
YES
NO
4. Press Yes to continue or No to abandon the operation and return to the pre-
vious screen.
5. If the operation is successful, confirmation of the number of Routes and
Waypoints saved/loaded is displayed.
USER CARD MENU
USER CARD PRESENT
SAVE COMPLETE
SAVED 2 ROUTE(S) AND
7 WAYPOINT(S)
CHECK
CARD IN
USER SLOT
LOAD WPT/ SAVE WPT/
RTE DATA RTE DATA
FROM CARD TO CARD
If the operation fails, the Save Failed message is displayed.
Download from Www.Somanuals.com. All Manuals Search And Download.
3-36
SL520/530/631 PLUS Chartplotter Displays
USER CARD MENU
USER CARD NOT PRESENT
SAVE FAILED
NO OR INCORRECT CARD
ENSURE USER CARD IS CORRECTLY
INSERTED IN THE LOWER SLOT
CHECK
CARD IN
USER SLOT
LOAD WPT/ SAVE WPT/
RTE DATA RTE DATA
FROM CARD TO CARD
➤ To receive incoming waypoints on SeaTalk or NMEA:
MARKS
1. To display the waypoint list press MARKS followed by the WAYPOINT LIST
soft key.
WAYPOINT
LIST
Press the WAYPOINT TRANSFER soft key.
2. Press the soft key RECEIVE WPTS FROM ST/NMEA.
The soft key changes to STOP RECEIVING WAYPOINTS.
When waypoints are transmitted by other equipment they are added to the
waypoint list on the chartplotter. Routes transmitted on NMEA are
appended to the route list.
WAYPOINT
TRANSFER
3. To disable waypoint transfer, press the soft keySTOP RECEIVING WAY-
POINTS.
Alternatively, press ENTER, or CLEAR, twice to close the Waypoint List.
➤ To send the waypoint list on NMEA:
1. Display the waypoint list as previously described, then press the WAY-
WAYPOINT
TRANSFER
POINT TRANSFER soft key.
2. Press the soft key SEND WPT LIST ON NMEA.
The soft key changes to STOP SENDING WAYPOINTS.
The waypoint and route lists are transmitted from the chartplotter to other
instruments on NMEA.
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 3: Standard Chart Operations
3-37
3.7 Using Tracks
The Track function is used to mark on-screen the trail that your vessel has
followed, as if it had left a visible fixed wake.
While the track is switched on it is recorded in the display unit’s memory. You
specify the interval at which track points are made and a line is drawn on-
screen betweeneachpoint. Up to 4500 trackpointscanbe saved in total:inthe
current track and in up to 5 track files (each a maximum of 750 points). The
current track remains on-screen, even following a power off/on, until you
clear the track.
Breaks in the track will be caused when any of the following occur for longer
than the specified track interval: the track is switched off then on; the position
fix is lost; the display unit is switched off.
To enable you to follow this track on your return voyage, the SmartRoute
function converts the track (or the last segment of a track with breaks) into a
route which is automatically reversed, see SmartRoute on page 3-41.
A track can be saved and retrieved for display at a later date. You can only
display one track at a time; you must clear a current track from the screen if
you want to display a saved track.
This section describes:
•
•
•
Setting up a track, including how to specify the interval.
Clearing the current track.
Managing tracks, using the track list, including Saving, Naming, Erasing
and Showing a track.
•
Making a Track into a Route
➤ To access the track controls:
1. From the chart display, press the MENU key to display the chart set up soft
keys.
SYSTEM
SET UP¬
CHART
SET UP¬
TRACK
SET UP¬
GPS
SETUP¬
2. Press the TRACK SETUP soft key to display the TrackDs41o62f-1t keys:
TRACKS
OFF ON
CLEAR
TRACK
MAKE INTO
ROUTE
MORE¬
D5674-1
The following instructions assume you have the track soft keys displayed.
Download from Www.Somanuals.com. All Manuals Search And Download.
3-38
SL520/530/631 PLUS Chartplotter Displays
Setting Up a Track
You use the track soft keys to switch the track on and to specify the interval, as
time or distance, at which track points are saved. The time interval between
track points can be set to 1s, 5s, 10s, 30s, 1min, 3min, 5min, 10min or
30minutes. The distance spacing between track points can be set to 0.1nm,
0.5nm or 1.0nm. The interval default is a distance of 0.1nm. The maximum
track length is 750 points. When the track has reached this length, the first
points are overwritten. The track issaved until you switchitoff. When the unit
is powered off, the current track (thus far) is retained in memory.
Setting a short time interval between track points is best suited to navigation
within a close or complex environment, e.g. an estuary or marina whereas, in
contrast, a greater distance interval is best suited to a long haul voyage.
Referto the setting guideshown in Figure 3-9to determine the best settingfor
your planned voyage; this is particularly important if you wish to use
SmartRoute to convert your track to a route.
1 sec 12½ min
5 sec
10 sec
30 sec
1 min
1 hr, 2½ min
2 hrs, 5 min
6 hrs, 15 min
12 hrs, 30 min
1 day, 13 hrs, 30 min
2 days, 14 hrs, 30 min
5 days, 5 hrs
15 days, 15 hrs
3 min
5 min
10 min
30 min
TRACK TIME
0.1 nm
0.5 nm
1.0 nm
75 nm
375 nm
750 nm
D4948-2
TRACK DISTANCE
Figure 3-9: Track Interval Setting Guide
You can change the setting at any time. The setting applies only to the current
track and is not saved as a stored track.
➤ To set up a track:
1. Press the MORE soft key to access the TRACK INTERVAL soft keys.
Pressthe appropriatesoftkeytoseteitheratime intervaloradistance inter-
val;presstheUParrowtoincreasetheinterval,theDOWNarrowtodecrease
the interval.
Press ENTER to return to the track soft keys.
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 3: Standard Chart Operations
3-39
TRACK INTERVAL
0.1nm
TRACK
LIST
MORE¬
D5674-1
2. Press the TRACK OFF ON soft key to toggle tracks on.
TRACK
OFF ON
Your vessels trail will be displayed on-screen, with a line joining the
points at the selected interval.
Clearing the Current Track
You can clear the current track from the screen. When you select CLEAR
TRACK, if the current track has not been saved, you have the option of saving it.
➤ To clear the current track:
1. Press the CLEAR TRACK soft key.
CLEAR
TRACK
2. If the track has not been saved the SAVE TRACK soft keys are displayed.
To clear the track without saving it in the Track List, press NO.
To save the track in the list, press YES. The Name track soft keys are dis-
played and you should continue as described in the following section, Sav-
ing and Naming a Track.
SAVE
TRACK
Press CLEAR to abort the Clear Track operation.
The current track is cleared from the screen and the default soft keys are
displayed.
Managing Tracks
Although itiseasy tosetupatrack, andthistrackisretainedeven ifyouswitch
off your display, you can store a number of different tracks so that you can
reviewthematalaterdate. Thissectionexplainshowtoperformthefollowing
tasks:
•
•
Save and Name a track.
Name, Erase and Show an existing track.
Saving and Naming a Track
You can save up to 5 named tracks in the Track List. These tracks can be re-
displayed at a later date.
➤ To save and name the current track:
1. Press the MORE soft key followed by the TRACK LIST soft key. The track list
TRACK
LIST
pop-up and associated soft keys are displayed.
Download from Www.Somanuals.com. All Manuals Search And Download.
3-40
SL520/530/631 PLUS Chartplotter Displays
2. The next available entry on the track list is highlighted.
(If required, you can use the trackpad to select another position in the list;
SAVE
TRACK
3. Press SAVE TRACK. The name track soft keys are displayed.
NAME TRACK?
YES
NO
D4256-1
4. If you do not wish to name or rename the track, press the NO soft key (or
CLEAR) to clear the list. The track is saved and is listed as Track Not
Named.
If you wish to name the track press the YES soft key. Use the trackpad to
move the cursor right or left to the character you wish to edit. Then use the
top or bottom of the trackpad to increase or decrease the letter or number.
You can use a Navigator Keypad (see Using the ST60 or ST80 Navigator
Keypad on page 3-15) to name the track.
5. Press ENTER to finish and clear the Track List, then to return to the default
soft key display, press ENTER again or CLEAR.
Naming, Erasing and Showing a Track
➤ To name an existing track, erase a track or show a track, you select the track
from the track list, then press the appropriate soft key as follows:
1. PresstheTRACKLIST softkey.TheTrackListisdisplayed. Theselectionbar
indicates the selected track.
TRACK
LIST
Select the required track then press the appropriate soft key.
NAME
TRACK
2. If you NAME a track, use the trackpad to move the cursor right or left to the
character you wish to edit. Then use the top or bottom of the trackpad to
edit the letter or number. Press ENTER finish the operation or CLEAR to
cancel the name, then ENTER to remove the track list.
3. If you ERASE a track you are prompted to confirm.
Press NO to cancel the operation, then ENTER to remove the track list.
Press YES to erase the track from the list, then ENTER to remove the track
list.
ERASE
TRACK
4. If you SHOW a track, and you have a current track on screen, you are
promptedtosavethetrack.ProceedaspreviouslydescribedinClearingthe
Current Track.
SHOW
TRACK
Alternatively, press the NO soft key to cancel the SHOW TRACK operation.
The track list is removed and the selected track is displayed.
5. Press ENTER or CLEAR to return to the default display.
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 3: Standard Chart Operations
3-41
SmartRoute
SmartRoute enables the current track, or the last segment of a track with
breaks, tobe converted toa route (the track could havebeenretrievedfrom the
track list). SmartRoute placesa waypointat the lasttrackpoint, then considers
each point in turn and determines the closest route through the recorded track.
The number of waypoints created is minimized, whilst maintaining optimum
correlation to the recorded track. On completion, the maximum deviation of
the route from the recorded track is displayed.
➤ To convert the current track into a route:
1. Select MAKE INTO ROUTE and press ENTER.
The current track is converted to a new route and becomes the current
route, with the most recently placed track point as the start of the route, i.e.
the track is reversed.
If there is an unsaved current route on screen, the option to save the route is
given, see Section 3.4, Working with Routes.
2. Check the calculated route and, in particular, that the route deviation from
the original, given in the warning box, is within navigable limits.
CAUTION:
Beforefollowingtheroute,ensurethatitissafefornavigation, notingthat
it may deviate from your actual path travelled.
Download from Www.Somanuals.com. All Manuals Search And Download.
3-42
SL520/530/631 PLUS Chartplotter Displays
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 4: Further Chart Operations
4-1
Chapter 4: Further Chart Operations
4.1 Introduction
This chapter explains how to use the additional functions that are provided on
the chartplotter display.
It covers the following topics:
•
•
•
•
•
•
Measuring distances and bearings on the chart, using the VRM/EBL key
Setting alarms and timers
Man Overboard (MOB)
Cursor Echo
GPS Setup
Data Log Mode
In ordertousesomeofthesefunctions, youmay need thefollowing additional
data from equipment connected to your system via a SeaTalk or NMEA link:
Table 4-1:
Function of External Data
Data
Example source Integrated functions available
Heading
COG
Compass*
GPS
- Head Up or Course Up heading modes
- MOB (if speed data also available)
Position
GPS system
- Waypoints
- Position, COG, SOG and time data in Data Box and Nav
Window
- MOB
- Data Log
Other data Transducers
- Data Box and Nav Window data displays, including speed,
depth, wind, temperature
*If heading datais availableviabothNMEA and SeaTalk, NMEA data takes priority. For allother data,
SeaTalk data takes priority (see Section 4.3).
Download from Www.Somanuals.com. All Manuals Search And Download.
4-2
SL520/530/631 PLUS Chartplotter Displays
4.2 Measuring Distances Using the VRM/EBL Key
You can obtain an accurate measurement of the distance and bearing between
two points by using the VRM/EBL key.
➤ To place a ruler line and Ruler data box:
1. Position the cursor on the starting point from which you wish to measure.
VRM/EBL
2. Press VRM/EBL.
A Ruler data box is displayed showing the bearing and distance from the
starting point to the cursor position. The character A appears at the cursor
location.
3. Use the trackpad to move the cursor to the measurement end point. A line
connects the cursor to the starting point, and the Ruler data box is updated
to show the bearing and length of the line as shown in Figure 4-1.
4. Press ENTER to fix the end point of the ruler line, and return to normal cur-
sor control. The letter B marks the location of the end point on the chart.
Figure 4-1: Measuring Distance Using a VRM
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 4: Further Chart Operations
4-3
➤ To re-position one end of the ruler line:
1. Move the cursor over the ruler line towards the end that you want to re-
position, until the letters A¡ B are displayed.
2. Press ENTER to take cursor control of the ruler. The ruler end moves to the
cursor which changes to a four-headed arrow.
3. Move the cursor to the required position. The ruler data box is updated.
4. Press ENTER again to set the position and return to normal cursor control.
Alternatively, press CLEAR to reset the ruler to the previous position.
➤ To clear the ruler line and ruler data box
either:
Move the cursor over the ruler line, until the letters A¡ B are displayed, then
press CLEAR.
VRM/EBL
or:
Press VRM/EBL, the ruler soft keys are displayed. Press RULER OFF ON to
RULER
OFF ON
toggle the ruler line and data box off.
➤ To clear the ruler data box:
Press VRM/EBL, the ruler soft keys are displayed. Press RULER DATABOX OFF
ON to toggle the ruler data box off.
RULER
DATABOX
OFF ON
➤ To move the Ruler data box, using the context-sensitive cursor:
BOX
1. Move the cursor over the box until the letters BOX are displayed, and press
ENTER to take cursor control of the box.
2. Use the trackpad to move the box to its new location, and press ENTER to
drop it and return to normal cursor operation.
Download from Www.Somanuals.com. All Manuals Search And Download.
4-4
SL520/530/631 PLUS Chartplotter Displays
4.3 Alarms and Timers
Alarm Reporting
The chartplotter reports the following alarms, that are set using the ALARMS
ALARMS
key:
Alarm
Indicates:
Arrival
Your vessel has arrived at the active waypoint: it has either
reached the arrival circle (the radius of which is specified) or,
has reached its closest point of approach (defined by a line
passing through the waypoint and perpendicular to the route
leg).
Off Track
Anchor
Your vessel has exceeded the specified distance (maximum
cross track error) from the active route leg.
Your vessel has drifted from its anchor position (set when the
alarm was turned on) by more than the specified distance.
Grounding
The chartplotter checks a sector ahead of your vessel for a
dangerous object (land, depth area, intertidal area, rock,
obstruction or shore obstruction). You specify the depth and
range of the sector from your vessel.
You can view a report of the objects that triggered the alarm.
Countdown
The countdown timer has reached zero.
Alarm Clock The time matches the specified alarm time.
The alarms are switched on or off, and the limits set, using the Alarms Set Up
menu, accessed from the ALARMS key.
When an alarm is triggered, the alarm buzzer sounds and a pop-up window
describing the alarm is displayed.
➤ To silence the alarm and clear the message, press any key.
If the alarm was generated by the chartplotter, the appropriate action is taken.
For example, following an arrival alarm, the next route leg is activated.
If an anchor alarm is silenced, but the alarm condition perstists, the alarm is
repeated every 30 seconds.
External Alarms
All SeaTalk system alarms (except autopilot alarms) are received and
displayed on the chartplotter. You can silence these alarms by pressing any
key. No other action is taken by the chartplotter except to silence the alarm.
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 4: Further Chart Operations
4-5
Setting Alarms and Timers
➤ To set up an alarm or timer:
1. Press the ALARMS key. The Alarms Set Up menu is displayed, showing
the current settings (see Figure 4-2).
ALARMS
2. Use the trackpad to move the selection barup ordown theoptions. Aseach
line is highlighted, the soft key labels are updated to show the current set-
tings and controls.
ALARMS SET UP
ARRIVAL ALARM
0.01nm
ON
OFF TRACK ALARM
ANCHOR ALARM
OFF
GROUNDING ALARM
COUNTDOWN TIMER
ALARM CLOCK
5M/1.0nm
00:33:00
OFF
SELECT ARRIVAL
ALARM RADIUS
D4265-4
Figure 4-2: Alarms Set Up List
3. Use the up or down soft keys to change the alarm setting. For example, for
the arrival alarm you can adjust the radius from the waypoint at which the
arrival alarm will be triggered.
The arrival, off track and anchor alarm distances can be set in the range
0.01 to 9.99 nm, in steps of 0.01nm.
Thegrounding alarm depth canbe setfrom1to20m in 1mstepsandcanbe
specified to cover a sector at a range from 0 to 1nm, in 0.1nm steps.
Thetimerissetinhours, minutesandseconds, andthealarmclockinhours
and minutes.
4. If required, press the ALARM OFF ON soft key to toggle the alarm on or off.
If youturn an alarmoff, itsvalue is retained andwillbeused when you turn
the alarm on again.
ALARM
OFF ON
Note: You can turn all the alarms and timers on and off, except for the Arrival
Alarm which is always on.
5. Press ENTER to save the changes and clear the list.
Download from Www.Somanuals.com. All Manuals Search And Download.
4-6
SL520/530/631 PLUS Chartplotter Displays
4.4 Man Overboard (MOB)
If you losea personorobjectoverboard, and need to return to the location, you
should use the Man Overboard (MOB) function.
menus (see Section 5.3).
Note: To obtain MOB position, you need either of the following:
•
•
Position data from a GPS or equivalent device
Heading and speed data, so that the position can be calculated by dead
reckoning
➤ To initiate the MOB procedure, press and hold the MARKS key for two
seconds. The system then performs the following tasks automatically:
MARKS
•
•
•
Redrawsthechartat1/2nm (evenifcartographyisnotavailablebutplotter
mode is on).
Marks the current position with a MOB symbol
current active waypoint and route.
which replaces any
Displays the MOB data box, showing the bearing and distance from your
vessel to the MOB waypoint position, and the elapsed time since the MOB
was initiated (Figure 4-3).
•
•
Displays the position data box, showing your vessel’s position.
As your vessel moves from the MOB position, a dotted line is displayed
connecting the MOB symbol and the vessel’s current position.
•
•
Sounds a 4-second alarm pattern every 30 seconds.
Sends an MOB message (including bearing and distance) to other units in
the system, via the SeaTalk connection.
MOB position
MOB
RNG 0.33nm
BRG 162°T
00:05:24
POSITION
N 49°54^76
W 002°09^83
MOB data box
D4273-2
Figure 4-3: MOB Display
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 4: Further Chart Operations
4-7
➤ To cancel the MOB, press and hold the MARKS key for 2 seconds.
The chart is re-drawn at its previous scale, and the MOB symbol and data box
MARKS
are removed.
Note: The MOB procedure can also be initiated or cancelled if the appropri-
ate SeaTalk message is received by the display unit.
4.5 Cursor Echo
In a systemwith a radardisplay connectedviaSeaTalk, you can set the display
to enable cursor echo. Cursor echo (accessed from System Set Up, described
in Section 5.3) enables you to display a radar cursor on the chart picture, or a
chart cursor on the radar picture(you cannot display a remote chart cursor in a
chart window nor a remote radar cursor in a radar window).
The following options can be toggled ON or OFF:
•
Radar Cursor In : displays the cursor from a radar on the chart window
(default - OFF).
•
•
Chart Cursor In: - not valid for the SL520/530/631PLUS display.
SeaTalk Cursor Out: enables the output, onto SeaTalk, of the display’s
own cursor (default - OFF).
•
Cursor Echo Local: - not valid for the SL520/530/631 PLUS display.
If you set the options to OFF, no cursor echo information is displayed.
When the appropriate option is switched on, the display shows its own cursor,
plus the cursor of the other display with appropriate cursor text (RDR) to
indicate its origin. This means that you could move the cursor over a target on
a radar display, and check the identity of the target by looking at the radar
cursor position on the chartplotter.
Download from Www.Somanuals.com. All Manuals Search And Download.
4-8
SL520/530/631 PLUS Chartplotter Displays
4.6 GPS Setup
GPS set up page provides you with information and the status of the tracked
navigationsatellitesforaSeaTalkGPS. Italsoenablesyouto SETUPaSeaTalk
Differential GPS, by manually retuning it to a different differential beacon.
The GPS Navigation Status pop-up window (shown in Figure 4-4) provides,
for each tracked satellite, the satellite number, a graphical signal strength bar
and its current usage status. HDOP and satellite Fix Status are also displayed.
Data for up to 12 satellites are shown.
NAVIGATION STATUS
SAT
AZ
ELEV
SIGNAL
STATUS
03
31
21
23
22
19
17
27
16
15
IN USE 085
IN USE 292
IN USE 127
IN USE 075
IN USE 174
IN USE 290
IN USE 056
SPARE 321
SPARE 024
SPARE 237
085
051
048
043
028
014
012
011
005
065
HDOP
FIX STATUS
1
FIX
D-GPS
SETUP¬
RESTART
GPS
D4281-2
Figure 4-4: Navigation Status Window
Positional accuracy is dependent upon certain parameters; in particular for
GPS, the azimuth and elevation angles are used in a triangulation process to
calculate position. HDOP (Horizontal Dilution Of Position) is a measure of
this accuracy; a higher figure signifies greater error. In ideal circumstances,
the figure should be in the region of 1.0. The Fix Status can indicate:
•
•
•
•
FIX, where a satellite fix has been acquired.
D-FIX, where a differential beacon fix has been acquired.
SD-FIX, where a satellite differential fix has been acquired.
NO FIX, where no fix can be acquired.
➤ To select GPS Set Up:
MENU
Press MENU, then press the GPS SETUP... soft key.
The Navigation Status pop-up window shown in Figure 4-4 is displayed.
GPS
SETUP¬
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 4: Further Chart Operations
4-9
Restart GPS
This soft key enables re-acquisition of a GPS position fix.
Note: Under normal circumstances RESTART GPS is not required.
D-GPS Set Up
The D-GPS SET UP function provides the ability to set up an external
DifferentialGPS, eitherautomatically (default) orby manuallyretuningitto
a different differential beacon.
In AUTO mode, the D-GPS is set to automatic and beacon selection is made
automatically by the beacon receiver. The beacon frequency and bit rate
received from the beacon receiver are displayed. The soft keys are disabled
and grayed out.
In MANual mode, youcanselectthe beaconfrequency and bit rate thatare sent
to the beacon receiver.
When you select D-GPS SETUP a pop-up window, providing the following
parameters, is displayed with associated soft keys:
•
Beacon ID - This shows the Beacon ID of the beacon transmitter. If no bea-
con has been found this item states NOT LOCKED.
•
Beacon Frequency - Both the menu item and associated soft keys show the
currently used differential beacon’s frequency in kHz. The frequency
range available is 283.5kHz to 325.0kHz.
•
•
Bit Rate - Both the menu item and associated soft keys show the currently
used differential beacon’s bit rate in bps. The rates available are 50bps,
100bps and 200bps.
Signal Strength and Signal to Noise Ratio - These items indicate the
received signal strength and Signal to Noise Ratio (SNR) in dB, received
from the beacon receiver. If the display unit is using RTCM data received
via NMEA, this information is not available and the item shows dashes,
one per character. The received Signal Strength and SNR are interrelated.
SNR provides a measure of the quality of the received signal and is depen-
dent upon signal strength.
•
Differential Age - This indicates the time elapsed since the last differential
beacon correction update.
➤ To tune a differential SeaTalk GPS to another beacon:
1. Press D-GPS SETUP, the Differential GPS Setup pop-up is displayed.
2. Press MODE AUTO MAN to toggle between AUTO and MAN modes; the
D-GPS
SETUP¬
selected mode is highlighted is indicated in the pop-up window.
Download from Www.Somanuals.com. All Manuals Search And Download.
4-10
SL520/530/631 PLUS Chartplotter Displays
Note: If the display unit is receiving RTCM data via NMEA, repeating a dif-
ferential fix from another unit, the MODE soft key is set to AUTO and is grayed
out. If receiving RTCM data, the setting must be performed manually on the
external DGPS receiver.
3. To set a new beacon manually, press BEACON SELECT, use the soft keys to
set the required beacon frequency and bit rate.
Press ENTER to return to the Differential GPS Setup pop-up window.
The status of the selected beacon is displayed in the pop-up.
Press ENTER to return to the Navigation Status window, then ENTER to
return to the MENU soft keys.
4.7 Data Log Mode
You can set the chartplotter to log course data every thirty minutes. Up to 48
log entriesare held, when48 entrieshavebeen made, the chartplotterwillstart
overwriting the first entries.
You start the log using soft keys provided in Data Log Mode. When you select
DataLogModethelogisdisplayedfull-screen.Ifthescreenisfull,youusethe
trackpad to scroll the list and view further log entries. Each line in the log
shows:
•
•
•
•
Time of log entry
Position at time of log entry
Course Made Good (CMG) since last log entry
Distance Made Good (DMG) since last log entry
Once you have enabled the data log, data is continually logged, but you must
set the display to Data Log Mode to view it. You use the DISPLAY key to
change the full-screen mode.
You can stop the log at any time and you can clear the log from memory.
If the chartplotter is switched off while the log is running, a dashed line willbe
displayed before the first new entry since switching the chartplotter on again.
➤ To activate Data Log Mode:
DISPLAY
1. Press DISPLAY, the DISPLAY pop-up is shown.
2. Press DISPLAY again, until LOG is selected, then press ENTER.
➤ To start recording log entries, press the START LOG soft key.
Asshown in Figure 4-5, thechartplotterrecords the time and vessels position.
Every thirty minutes the time, new position, distance made good and course
made good are recorded.
START LOG
The START LOG soft key changes to STOP LOG.
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 4: Further Chart Operations
4-11
TIME POSITION
CMG
DMG
6.86KM
15:30
16:00
16:30
17:00
17:30
18:00
18:30
19:00
19:30
346°M
50°21^890N
001°20^610W
50°18^010N
001°20^070W
50°21^850N
001°19^290W
50°18^500N
001°21^300W
50°20^990N
001°18^280W
50°19^660N
001°21^960W
50°19^730N
001°18^030W
50°20^930N
001°21^750W
50°18^550N
001°18^650W
7.23KM
7.23KM
6.67KM
5.74KM
5.00KM
4.63KM
5.00KM
5.74KM
180°M
012°M
206°M
043°M
245°M
093°M
302°M
145°M
STOP LOG
CLEAR LOG
D4284-1
Figure 4-5: Data Log Window
➤ To stop recording log entries:
Press the STOP LOG soft key.
➤ To clear the log entries:
STOP LOG
Pressthe CLEARLOG softkey, youareprompted “AreYou Sure”. To cancel the
CLEAR LOG operation press the NO soft key.
CLEAR LOG
To continue press the YES soft key, all log entries are deleted, but the data log
remains active.
➤ To return to the chart display:
DISPLAY
Press DISPLAY to select the chart mode, then press ENTER.
The log continues until you return to the data log mode and press STOP LOG.
STOP LOG
Download from Www.Somanuals.com. All Manuals Search And Download.
4-12
SL520/530/631 PLUS Chartplotter Displays
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 5: Setting Up the System Defaults
5-1
Chapter 5: Setting Up the System Defaults
5.1 Introduction
Once you have installed your display unit and are familiar with its basic
operation (described in Chapter 1 and Chapter 2), you needto set it up so that
itobtainsthecorrectinformationfromtheequipmentyouhaveconnecteditto,
operates according to your requirements, and displays information according
to your preferences.
This is achieved using the soft key controls that are displayed when you press
MENU
the MENU key.
In most cases, you will only need to use the MENU key options when you first
set up your system. However, you may decide to change the way you have
customized some aspects, such as the screen and help setting, as you become
more familiar with your system.
Onceyouhavesetthevalues,theyremainasthedefaultsettingsuntilyoureset
them; they are retained even if you power off your display.
This chapter covers the following topics:
•
•
•
Changing the default set up parameters
System parameter functions and default settings
Chart specific parameter functions and default settings
You should check the functions of the parameters, and decide on the new
settings, before making the changes.
Download from Www.Somanuals.com. All Manuals Search And Download.
5-2
SL520/530/631 PLUS Chartplotter Displays
5.2 Changing the Set Up Parameters
The set up parameters are divided into two sections:
•
System, to control the aspects of the system that are not specific to the
chart.
•
Chart, tocontrolthechartplotterdisplay, includingwaypointinformation
and vectors.
Note: The GPS and Track Set Up menus are described in Chapter 4.
This section provides instructions for displaying and changing the default
values. The following sections list the parameters and their possible settings,
and describe the function of each parameter in turn.
➤ To set the default parameters:
1. Press the MENU key to display the set up soft keys - the options available
MENU
depend on the selected operating mode.
SYSTEM
SET UP¬
CHART
SET UP¬
TRACK
SET UP¬
GPS
SETUP¬
D4162-1
2. Press the soft key for the set up you require.
The requested set up menu is displayed, listing the parameters and their
current settings.
3. Use the trackpad to move the selection bar up and down the list. An arrow
is displayed at the top or bottom right-hand corner if you can scroll the list
to display further parameters.
As each line is highlighted, the soft keys are updated to show the settings
available.
• For parameters that have a numeric value, or more than four possible
settings, a scroll list is displayed above two of the soft keys.
• Some parameters are controlled by a slider that is displayed above two
of the soft keys.
• For some parameters, a soft key provides access to a sub-menu of fur-
ther options.
4. Pressthesoftkeycorrespondingtothedesiredsettingor,forscrolllists,use
the soft keys to scroll forwards or backwards through the list until the
required setting is displayed. This setting is retained when you move the
selection bar on to the next parameter in the menu list.
For sliders, press the appropriate soft key repeatedly to increase or
decrease the slider value in individual steps, or press and hold the key to
change the setting quickly.
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 5: Setting Up the System Defaults
5-3
5. Once you have set all the required values, press ENTER to clear the menu
and return to the set up soft keys.
6. Press ENTER, MENU or CLEAR to clear the soft keys and return to the
default display.
You can return all the settings to their original factory settings, if required, by
performing a factory reset as described in Chapter 7.
Download from Www.Somanuals.com. All Manuals Search And Download.
5-4
SL520/530/631 PLUS Chartplotter Displays
5.3 System Set Up Parameters
The following table lists the System menus and their options, shows the
factory default setting, and provides a space for you to make a note of your
new default setting. Each parameter is described in the following subsections.
Table 5-1:
System Set Up Parameters
Menu
Options
Factory
Default
New
Default
DATA BOXES
POSITION
SPEED
OFF, LAT/LONG, TDs
OFF or ON
OFF or ON
OFF or ON
OFF or ON
OFF or ON
OFF or ON
OFF, APP, TRUE or BOTH
OFF, LAT/LON, or
RNG/BRG/TTG
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
DEPTH
COG
SOG
TIME
DATE
WIND
WAYPOINT
CROSS TRACK ERROR OFF or ON
OFF
OFF
OFF
OFF
OFF
OFF
OFF
HEADING
LOG/TRIP
PILOT
OFF or ON
OFF or ON
OFF or ON
VMG
OFF, WIND, WPT or BOTH
TEMPERATURE
TIDE SET/DRIFT
OFF or ON
OFF or ON
BEARING MODE
MAGNETIC, TRUE
TRUE
CURSOR REFERENCE
CURSOR READOUT
MAG/TRUE, RELATIVE
RELATIVE
RNG/BRG
OFF,LAT/LONG,RNG/
BRG,BOTH
DAY/NIGHT
HELP
DAY, NIGHT
OFF/ON
DAY
ON
SOFT KEYS
OFF/ON
ON
KEY BEEP
OFF/ON
ON
MOB DATA
PILOT POP-UP
MENU TIMEOUT PERIOD
DR, POSITION
OFF/ON
DR
OFF
NO TIMEOUT, 10, 20, 30
SECONDS
NO TIMEOUT
DISTANCE UNITS
SPEED UNITS
NAUTICAL MILES, STATUTE
MILES, KILOMETERS,
KILOYARDS
NAUTICAL MILES
KNOTS
KNOTS, MILES PER HOUR,
KILOMETERS PER HOUR
DEPTH UNITS
METERS, FEET, FATHOMS
CENTIGRADE, FAHRENHEIT
FEET
TEMPERATURE UNITS
FAHRENHEIT
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 5: Setting Up the System Defaults
5-5
Table 5-1:
System Set Up Parameters
Menu
Options
Factory
Default
New
Default
VARIATION SOURCE
AUTO, MANUAL
OFF or ON
AUTO
ON
BRIDGE NMEA HEADING
NMEA OUT SET UP
APB
OFF or ON
OFF or ON
OFF or ON
OFF or ON
OFF or ON
OFF or ON
OFF or ON
OFF or ON
OFF or ON
OFF or ON
OFF or ON
OFF or ON
OFF or ON
OFF or ON
OFF or ON
OFF or ON
OFF or ON
OFF or ON
OFF or ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
BWC
BWR
DBT,
DPT
MTW
RMB
RSD
RTE
TTM
VHW
VLW
WPL
GGA
GLL
RMA
RMC
VTG
ZDA
CURSOR ECHO
RADAR CURSOR IN
CHART CURSOR IN
OFF or ON
Not valid for SL520/530/631
PLUS display
OFF
OFF
S/T CURSOR OUT
CURSOR ECHO LOCAL
OFF or ON
Not valid for SL520/530/631
PLUS display
OFF
ON
DATE FORMAT
TIME FORMAT
TIME OFFSET
DD/MM/YY, MM/DD/YY
12 HOUR, 24 HOUR
MM/DD/YY
12 HOUR
UTC
UTC, or local offset value:
Plus or minus up to 13 hours,
in whole hours
GPS SOG/COG FILTER
HIGH, MEDIUM, LOW
MEDIUM
-
COMPASS SET UP
LINEARISE COMPASS
Press soft key to start the
linearisation procedure and
to align the heading
ALIGN HEADING
LANGUAGE
ENGLISH (UK), ENGLISH
(US), DANISH, FRENCH,
GERMAN, DUTCH, ITALIAN,
ICELANDIC, NORWEGIAN,
PORTUGUESE, SPANISH,
SWEDISH, FINNISH
ENGLISH (US)
SIMULATOR
OFF, DATA, RADAR, BOTH
OFF
Download from Www.Somanuals.com. All Manuals Search And Download.
5-6
SL520/530/631 PLUS Chartplotter Displays
Data Boxes
Pressthe SELECT BOXES softkey to display the databox sub-menu. Thisallows
you to select up to 6 data boxes that you can display.
Note: 1. A fixed set of 9 (mono) or 16 (color)of these data items are available
for display in the Nav Data half-screen window (see Chapter 2).
2. In additionto thesegrouped data boxes, boxes for the cursorreadout, VRM/
EBL data, waypoint data, MOB data and simulator status are displayed when
selected or when the appropriate function is active..
Data boxes provide regularly used data in a compact form so that most of the
picture can still be seen. The ones you select here can be turned on and off as a
groupduringnormaloperation, andyoucanalsomovethemaroundthescreen
individually using the context-sensitive cursor (see Context-Sensitive Cursor
Control on page 1-9.).
Bearing Mode
The mode (magnetic or true) of all the bearing and heading data displayed.
This is indicated in the status bar after the heading value.
Cursor Reference
information can be displayed in either of two forms:
•
Relative: The bearing relative to your vessel’s heading.
Mag/True: The actual bearing in either degrees magnetic or degrees true.
If you choose this mode, the selection you made for the previous parame-
ter (Bearing Mode), °M or °T, is displayed in the cursor (Rng/Brg) data
boxes. The current units are shown for the heading value in the status bar
at the top of the screen.
Cursor Readout
Thisoptioncontrolswhetherthecursordata isshowninlatitude andlongitude
or in range and bearing. Alternatively, you can show both types of readout, in
separate boxes, or turn the cursor data box off.
You can also turn the cursor readout box(es) on and off during normal
operation, via the SCREENdefault softkey (seeSwitching the CursorDataBox
On and Off on page 2-10.)
Day/Night
This option allows you to change the display between day and night modes.
If you select NIGHT mode, a different palette, more suited to night time
viewing is used.
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 5: Setting Up the System Defaults
5-7
Help
When Help is set to ON, a prompt appears when selecting a soft key or menu
choice, and when using the context-sensitive cursor. The help message is
cleared when an action is selected.
Soft Keys
WhentheSoftKeysoptionissetto ON, thedefaultsoftkeysaredisplayedifno
other operation is in progress.
When the Soft Keys option is set to OFF, the default soft keys are only
displayed when a soft key is pressed, and they disappear if no operation is
performed for 10 seconds.
Key Beep
This option controls whether or not the keys make a noise when you press them.
MOB Data
This option controls whether MOB data is based on position data, or on dead
reckoning (DR). Dead reckoning normally provides a better indication of the
course to an object in the water, on the assumption that your vessel and the
object are both subject to the same tide and wind effects.
Autopilot Pop Up
Thisoptioncontrolswhetherornottheautopilotpopupisdisplayed.Whenset
to ON, if the status and locked heading of the autopilot changes, they are
displayed in a pop up box. The box is removed from the display after two
seconds.
When Autopilot Pop Up is set to OFF, the pop up box is disabled.
Menu Timeout Period
With no timeout set, menus and soft key labels remain displayed until you
clear them by pressing ENTER, CLEAR or the appropriate dedicated key.
Ifyousetavaluehere, themenusandsoftkeylabelswillbeclearedifakeyhas
not been pressed for the specified number of seconds.
This setting does not affect the default soft key labels, which are controlled by
the Soft Keys option (see above).
Units
You can set the units for speed, depth and temperature. The units you set will
be used to display all data, including information received from other
instruments on the system.
Download from Www.Somanuals.com. All Manuals Search And Download.
5-8
SL520/530/631 PLUS Chartplotter Displays
Variation Source
The variation value is the difference between True and Magnetic direction
data for heading or bearing values. The Variation Source option provides soft
keys for selecting Auto or Manual variation mode, displays the current
variation value for each and highlights the currently selected mode.
Auto Mode
If you select Auto mode, the display obtains the value of variation
automatically, normally from received data. The variation value that is used
dependsonthe dataavailable, andisselectedinthefollowing orderofpriority:
1. Variation value from the same source as the heading data:
• If heading data is being taken from NMEA, then variation is also taken
from NMEA
• If heading is taken from SeaTalk, then SeaTalk variation is used
2. Variation value from a different source:
• If heading data is being taken from NMEA, but no NMEA variation is
available, then variation is taken from SeaTalk
• If heading is taken from SeaTalk, but no SeaTalk variation is available,
then variation is taken from NMEA
3. A calculated variation value, using position data, if no SeaTalk or NMEA
value is available
4. The current manual variation value, if no SeaTalk or NMEA value and no
position data is available
Manual Mode
If you select Manual mode, by pressing either of the MANUAL keys, you can
specify the local variation value according to the area in which you are
operating. Press the appropriate MANUAL key to adjust the variation up or
down, to a maximum of 30° East or West.
This value is then transmitted to any other SeaTalk instruments on your
system. It is retained if you turn the display off and on again.
In Manual mode, incoming NMEA variation is ignored. However, if the
variation is changed on another SeaTalk instrument, the new value is used and
the manual value that is displayed is updated.
Note: The Manual variation value defaults to 0°, so it is important to set up a
value if variation is not available from an external source.
Bridge NMEA Heading
The display bridges NMEA input data to the SeaTalk bus (see Section 6.8).
The Bridge NMEA Heading option can be used to prevent NMEA heading
data being bridged onto the SeaTalk bus.
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 5: Setting Up the System Defaults
5-9
For example, if you have a course computer connected on SeaTalk and
NMEA, and an active compass connected on NMEA, SeaTalk data overrides
NMEA data in the course computer. You should therefore switch OFF the
Bridge NMEA Heading option to ensure the course computer receives the
same NMEA heading input as the display system.
NMEA Out Set Up
This option lets you switch off individual NMEA out sentences.
Cursor Echo
You can set up an integrated system so that radar and chartplotter displays
connected via SeaTalk can display each other’s cursors.
Cursor echo functions so that you can display a chart cursor on the radar
picture, or a radar cursor on the chart picture (you cannot display a remote
radar cursor in a radar window nor a remote chart cursor in a chart window).
When the appropriate options are switched on, each display shows its own
cursor, plus the cursor of the other display with appropriate cursortext (RDR or
CHT) to indicate its origin. This means that you could move the cursor over a
targetonthe radardisplay, and checkthe identity ofthe target by looking atthe
radar cursor position on the chartplotter.
Press the CURSOR ECHO soft key to display the cursor transfer soft keys. The
following options can be toggled ON or OFF:
•
Radar Cursor In: displays the cursor from a radar on the chart display
(default - OFF).
•
Chart Cursor In: - not valid for the SL520/530/631 PLUS display.
Note: The remotedisplaymusthaveSeaTalk Cursor Outenabled. Raymarine
recommend that in multi-display systems, you do not enable Cursor Out on
more than two displays. If multiple displays have cursor out enabled, the cur-
sors will not be displayed simultaneously, but will flash on/off.
•
SeaTalk Cursor Out: enables the output, onto SeaTalk, of the display’s
own cursor (default - OFF).
•
Cursor Echo Local: - not valid for the SL520/530/631 PLUS display.
If you set the options to OFF, no cursor echo information is displayed.
Date and Time Settings
Set your preferred date format (DD/MM/YY or MM/DD/YY) and time
format (12 or 24 hour). If you wish to display local time, use the soft keys to
change from UTC to the required time offset. This can be up to plus or minus
13 hours, in hourly steps.
Download from Www.Somanuals.com. All Manuals Search And Download.
5-10
SL520/530/631 PLUS Chartplotter Displays
GPS SOG/COG Filter
The SOG/COG filter averages the velocity vectors to compensate for the
oscillating motion of the vessel, giving a clearer indication of the vessel’s
courseandspeed.ThefilterdoesnotaffectthecalculationoftheGPSposition.
The velocity vectors calculated from the GPS Signal give an instantaneous
measure of speed and direction of the GPS antenna. The COG and SOG can
therefore seem erratic under certain conditions. For example, when a vessel is
moving slowly through rough seas, the antenna moves from side to side as
well as in the direction of the vessel.
Slow moving vessels, or vessels sailing in rough seas will benefit from a high
setting, whereasapowerboatthatcan quickly changespeedanddirectionwill
benefit from a low setting.
Select the SOG/COG filter setting as required. This can be set to HIGH,
MEDIUM or LOW.
Compass Set Up
This option is used to calibrate a Raymarine heading sensor such as the
Pathfinder Smart Heading System. Controls are provided for Linearise
Compass which detects and corrects for heading errors caused by metal
objects, and Align Heading which matches the displayed heading to a known
heading or transit.
Refer to the Handbook supplied with your heading sensor for more details.
Language
Select the language in which you wish information to be displayed. The
selected language will be used for screen text, labels, menus and options, but
will not affect the letters displayed by the context-sensitive cursor. The
language setting also affects the display format for lat/long position
information.
Simulator
The simulator allows you to operate your display without data from the
antenna and/or external data sources. The system set up simulator options
have the following functions:
•
Data provides simulated numerical data, and a waypoint display.
When the simulator is switched on, a SIMULATOR data box is displayed during
operation, showing the simulation selected.
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 5: Setting Up the System Defaults
5-11
5.4 Chart Set Up Parameters
The CHART SET UP option allows you to set up the chartplotter according to
your system configuration and your personal preferences.
The following table lists the Chart Set up parameters and their options, shows
the factory default setting, and provides a space for you to make a note of your
new default setting. Each parameter is described in the following subsections.
Table 5-2:
Chart Set Up Parameters
Parameter
Options
Factory Default
New Default
CUSTOMIZE CHART
PLOTTER MODE
See below for details
OFF, ON
OFF
CHART
ORIENTATION
NORTH UP, COURSE UP,
HEAD UP
NORTH UP
OBJECT
OFF, ON POINTS, ON ALL
ON ALL
INFORMATION
WAYPOINT SYMBOLS
OFF, ON
ON
ON
WAYPOINT NUMBERS OFF, OFF
DEFAULT WAYPOINT
SYMBOL
,
,
,
HEADING VECTOR
INFINITE
OFF
OFF
OFF
COG VECTOR
TIDE VECTOR
OFF, 3 MINS, 10 MINS,
INFINITE
OFF, 10 MINS, 1 HOUR,
INFINITE
RADAR/CHART
SYNCH
Not valid for SL520/530/
631 PLUS display
DATUM SELECTION
POSITION OFFSET
WGS 84, LOCAL
SET UP, OFF/ON
WGS 84
OFF
Customize Chart
This provides a list of chart options, enabling you to specify how the chart
features are displayed. Most options can be toggled between on, off and
custom - custom passes on/off control to the SCREEN soft keys (see
Customizing the Screen Presentation Options on page 2-10).
The following features can be set using Customize Chart, factory default
settings are shown in bold type:
•
•
•
chart text (on, off, custom)
chart text size (small, normal, large)
chart display (detailed, simple)
Download from Www.Somanuals.com. All Manuals Search And Download.
5-12
SL520/530/631 PLUS Chartplotter Displays
•
•
•
•
•
•
•
•
•
•
•
•
chart boundaries (on, off, custom)
spot soundings (on, off, custom)
depth shading limit (set the limit)
depth contours (on, off, custom)
depth contour display (set the upper and lower limits)
nav marks (on, off, custom)
nav marks icon (international, US)
light sectors (on, off, custom)
caution and routing data (on, off, custom)
marine features (on, off, custom)
land features (on, off, custom)
icon display (simple, detailed, custom)
The factory default for CUSTOM options is ON.
Plotter Mode
PlotterMode enablesyou to zoomintoa smallerarea, evenwhen nochartdata
is available for that scale. This allows you use the chartplotter functions at
large scales even when a chart card is not installed.
Chart Orientation
The chart orientation is normally North Up, but can be changed to Course Up
or Head Up if heading data is available. The orientation modes give the
following displays:
•
North Up: The chart is displayed with north upwards. As you change
heading, the ship’s heading marker moves. This is the default mode, and is
the only mode available if there is no heading data.
•
Course Up: The chart is stabilized and displayed with the currently
selected course upwards. If you select a new course, the picture rotates to
display the new course upwards.
The reference used for the Course Up depends on the information avail-
able. The first available in the following is used:
i. A locked heading over a SeaTalk connection
ii. The heading at the time Course Up was selected
To update the Course Up reference while Course Up is the current mode,
re-select Course Up from the set up menu.
•
Head Up: The chart is displayed with the vessel’s current heading
upwards. As the heading changes the chart will rotate.
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 5: Setting Up the System Defaults
5-13
Object Information
You can set Object Information ON ALL, ON POINTS or OFF to determine when
an object identification pop-up is displayed. When set to ON ALL, the
information pop up is displayed when the cursor is placed over any chart area
fortwo seconds. ON POINTS enablestheinformationpopup when the cursor is
placed over a displayed chart object and OFF disables the information pop up.
Waypoint Options
Waypoint Symbols controls whether or not the waypoints are shown on the
Chart display, with their appropriate symbols. The active waypoint, and
waypoints in the current route are always shown.
Waypoint Numbers controls whether or not the waypoint numbers are
shown for any waypoints in the current route.
Default Waypoint Symbol lets you select the symbol you want used for
waypoint display.
Vectors
Heading, Tide and Course Over Ground vectors can be displayed as a line
from your vessel. The length of the vector is determined by your choice of
SOG and the time period. An infinite vector extends to the edge of the chart
screen.
Heading Vector indicates your current heading.
COG Vector indicates your course over ground.
Tide Vector indicates the tide angle. Tide information is calculated from the
speed through water, compass and position data.
Radar/Chart Synch
Not valid for SL520/530/631 PLUS display.
Datum Selection
You can select either WGS 84 or LOCAL datum. In LOCAL mode, you are
presented with a list of datums; use the trackpad to scroll through the list, then
press ENTER to select the option and close the menu.
CAUTION:
Changing the chart datum does not cause any waypoint or routes stored
in the chartplotter to move on the display, although their latitude and
longitude changes to reflect the new datum.
Download from Www.Somanuals.com. All Manuals Search And Download.
5-14
SL520/530/631 PLUS Chartplotter Displays
When adding waypoints numerically to the waypoint list, or via SeaTalk
or NMEA, it is important that they are referenced to the same datum to
which the display is currently set.
When you change datum selection, the system attempts to set any connected
GPS to the new mode, using SeaTalk and NMEA set up commands. A
message shows whether the set up was successful or not.
Position Offset
You can offset the vessel position to allow for differences between the GPS
and paper chart data. This may be useful if you are using a datum that is not
available on the Chartplotter, or if you are referring to a paper chart drawn to
unknown datum.
You can change the offset by moving the cursor to the known vessel position.
This offset is applied to all incoming position data. The default offset value is
zero.
When position offset is switched on, all displayed vessel position data is
annotated (C) to indicate it has been corrected.
➤ To switch the position offset on/off:
1. Select the POSITION OFFSET option, then press the OFFSET OFF ON soft key
to toggle the option on/off. The last selected offset value is added to posi-
tion data and the vessel is displayed at the corrected position.
➤ To set a new offset value:
1. Select the POSITION OFFSET option, then press the SET UP OFFSET soft key.
If necessary, position offset is automatically toggled on.
2. Usethetrackpad to movethecursorto the requiredvesselposition; the cur-
sor position is displayed in a position offset data box.
3. Press the ACCEPT OFFSET soft key, the vessel is displayed at the new posi-
tion. Press ENTER to return to the default display.
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 6: Installation
6-1
Chapter 6: Installation
6.1 Introduction
This chapterprovides installation instructions for your SL520/530/631 PLUS
display. Details for mounting the SL520/530/631 PLUS display and
connecting the equipment are included.
•
To install display unit follow the instructions in Section 6.2 to Section 6.6.
ou should then test the display as described in Section 6.7.
•
To connect your display to other equipment, follow the guidelines in
Section 6.8 and Section 6.9, taking particular care to ensure the correct
polarity of the SeaTalk supply.
Display Unit
GPS
Box
SeaTalk
Compass
Distribution Panel
NMEA
12/24V Supply
12V Supply
12V Supply
D4288-1
Figure 6-1: Typical Chartplotter System
Note: If you wish to practice using the display before installation, connect a
12V or 24V DC power supply (connecting the red wire via a 6.3A quick blow
fuse to positive and the black wire to negative) and using the simulator mode,
as described in Chapter 2.
Download from Www.Somanuals.com. All Manuals Search And Download.
6-2
SL520/530/631 PLUS Chartplotter Displays
For full functionality of the chartplotter you need to provide position and
heading data.
•
•
•
Orientation -heading datais requiredforchart to operate in Course Up and
Head Up.
MOB requires heading and speed data. Alternatively, SOG and COG
(derived from the same source as position data) enable the MOB function.
Position data is required for full functionality of the chart display.
Full details of heading, position and other data are given in Section 6.8.
Planning the Installation
Before you install your system, plan the installation, considering:
•
•
Location of the display unit, as described in Section 6.3.
Cable Runs, including cables for an integrated system (to provide heading
and position data etc.), as described in Section 6.4.
EMC Installation Guidelines
All Raymarine equipment and accessories are designed to the best industry
standards for use in the recreational marine environment.
Their design and manufacture conforms to the appropriate Electromagnetic
Compatibility (EMC) standards, but correct installation is required to ensure
thatperformanceis notcompromised. Althougheveryefforthasbeentaken to
ensurethattheywillperformunderallconditions, itisimportanttounderstand
what factors could affect the operation of the product.
The guidelines given here describe the conditions for optimum EMC
performance, butitisrecognizedthatitmaynotbepossibletomeetallofthese
conditions in all situations. To ensure the best possible conditions for EMC
performance within the constraints imposed by any location, always ensure
the maximum separation possible between different items of electrical
equipment.
For optimum EMC performance, it is recommended that wherever possible:
•
Raymarine equipment and cables connected to it are:
• At least 3 ft (1 m) from any equipment transmitting or cables carrying
radio signals e.g. VHF radios, cables and antennas. In the case of SSB
radios, the distance should be increased to 7 ft (2 m).
• More than 7 ft (2 m) from the path of a radar beam. A radar beam can
normally be assumed to spread 20 degrees above and below the radiat-
ing element.
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 6: Installation
6-3
•
The equipment is supplied from a separate battery from that used for
engine start. Voltage drops below 10 V, and starter motor transients, can
causetheequipmenttoreset. Thiswillnotdamagetheequipment, butmay
cause the loss of some information and may change the operating mode.
•
•
Raymarine specified cables are used. Cutting and rejoining these cables
can compromise EMC performance and must be avoided unless doing so
is detailed in the installation manual.
If a suppression ferrite is attached to a cable, this ferrite should not be
removed. If the ferrite needs to be removed during installation it must be
reassembled in the same position.
Suppression Ferrites
The following illustration shows typical cable suppression ferrites used with
Raymarine equipment. Always use the ferrites supplied by Raymarine.
D3548-4
Figure 6-2: Typical Suppression Ferrites
Connections to Other Equipment
If your Raymarine equipment is to be connected to other equipment using a
cable not supplied by Raymarine, a suppression ferrite MUST always be
attached to the cable near to the Raymarine unit.
Download from Www.Somanuals.com. All Manuals Search And Download.
6-4
SL520/530/631 PLUS Chartplotter Displays
6.2 Unpacking and Inspecting the Components
Unpack your system carefully, to prevent damage to the equipment. Save the
carton and packing, in case you need to return a unit for service.
Checkthatyouhaveallthecorrectsystem components. Thesedependonyour
system package, as follows:
Table 6-1:
Parts and Accessories
Item
Part No
Supplied with:
Option for:
7”Mono LCD Display
7” Color LCD Display
10.4” Color Display
E32046
E32047
E32048
SL520 PLUS
SL530 PLUS
SL631 PLUS
-
-
-
Display Accessories
7” Sun cover
10.4” Sun cover
D331
E55031
SL520/530 PLUS
SL631 PLUS
Handbook
Quick Reference Card, Chart
81209
86079
SL520/530/631 PLUS
SL520/530/631 PLUS
-
-
7” Mounting bracket assy
Trunnion knobs (x2)
W143
W145
SL520/530 PLUS
All
-
-
7” Flush Mount Kit
10.4” Mounting bracket assy
10.4” Flush Mount Kit
M92708
E55032
E55033
-
SL520/530 PLUS
-
SL631 PLUS
SL631 PLUS
-
Power cable
W144
All
-
Seatalk cable assembly -
Flat moulded plugs both ends:
3 ft 3 in (1 m) long
9 ft 9 in (3 m) long
16 ft 3 in (5 m) long
29 ft 3 in (9 m)) long
W284
W285
W286
W287
-
-
-
-
All
All
All
All
Flat to male round connector:
12 in (0.3 m) long
Flat to female round connector:
12 in (0.3 m) long
D187
D188
-
-
All
All
Flat moulded plug one end only:
3 ft. 3 in (1 m) long
Ferrite for SeaTalk Cable
Seatalk junction 3-way block
Seatalk auxiliary junction box
D229
-
D244
R55006
-
All
-
All
-
-
All
-
NMEA OUT cable assy
4 ft 11 in (1.5m)
R55005
All
-
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 6: Installation
6-5
6.3 Selecting the Display Unit Location
The display unit can be mounted using the mounting bracket supplied, or
console mounted using the optional flush-mounting kit.
The dimensions of the display unit, including the bracket, are shown in
Figure 6-3, Figure 6-5 and Figure 6-4.
When planning the display installation, the following should be considered to
ensure reliable and trouble free operation:
•
Convenience:ThecontrastandcolorsseenonallcolorLCDdisplaysvary
slightly with viewing angle; this is more noticeable on the left hand side.
Power the unit and select a suitable mounting location prior to installing
the display.
The mounting location should be easily accessible to allow operation of
the front panel controls.
•
•
Access: There must be sufficient space behind the display to allow cable
connections to the rear panel connectors, avoiding tight bends in the cable.
Interference: The selected location should be far enough away from
devices that may cause interference, such as motors, generators and radio
transmitter/receivers (see the EMC guidelines earlier in this section).
•
•
Magnetic compass: Mount the display unit at least 3 ft (1m) away from a
magnetic compass.
Cableruns:ThedisplayunitmustbelocatednearaDCpowersource. The
power cable supplied is 4.9 ft. (1.5m), but a longer cable can be used if
required: refer to Section 6.4.
•
Environment:Donotrestrictairflowattherearofthedisplayunit;the
color display incorporates Cold Cathode Florescent Lamps (CCFL),
which have a reduced light output when the unit is very hot.
Ensure there is adequate ventilation, particularly if the display unit is
pod-mounted.
The display should be protected from physical damage and excessive
vibration. Although the display unit is waterproof, it is good practice to
mount it in a protected area away from prolonged and direct exposure to
rain and salt spray.
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 6: Installation
6-7
0.95 in
(24.3 mm)
6.89 in (175 mm)
10.51 in (267 mm)
8.8 in (223.6 mm)
GAIN
VRM/EBL
MULTI
DISPLAY
MARKS
ALARMS
RANGE
POWER
ENTER
CLEAR
MENU
4.53 in (115 mm)
1.42 in (36 mm)
6.9 in (176 mm)
cable cleareance
3.15 in
(80 mm)
Weight: 7.7 lbs (3.5 Kg)
6.3 in (160 mm)
8.85 in (225 mm)
1.28 in (32.5 mm)
Compass Safe Distance: 39 in (1 m)
D5063-1
Figure 6-4: 7” Color LCD Display Dimensions
Download from Www.Somanuals.com. All Manuals Search And Download.
6-8
SL520/530/631 PLUS Chartplotter Displays
3.82 in (97 mm)
11.5 in (292 mm)
6.38 in (162 mm)
cable clearance
12.9 in (328 mm)
9.7 in (246 mm)
0.87 in (22.1 mm)
Weight: 12.65 lbs (5.75 kg)
Compass Safe Distance: 39 in (1 m)
7.88 in (200 mm)
11.26 in (286 mm)
1.7 in (43 mm)
D5066-1
Figure 6-5: 10.4” Color LCD Display DImensions
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 6: Installation
6-9
6.4 Cable Runs
Consider the following before installing the system cables:
•
You need to attach the power cable. Additional cables will be required if
you are installing an integrated system.
•
All cables should be adequately secured, protected from physical damage
and protected from exposure to heat. Avoid running cables through bilges
or doorways, or close to moving or hot objects.
•
•
Acute bends must be avoided
Where a cable passes through an exposed bulkhead or deckhead, a water-
tight feed-through should be used.
•
Secure cables in place using tie-wraps orlacing twine. Coil any extra cable
and tie it out of the way.
You need to run the following cables:
•
Power/NMEA Input cable, supplied with the display unit. This has acon-
nector plug at one end for connecting the display unit, and 7 wires at the
otherend for connecting the powersupply and optional NMEA inputs (see
Section 6.8, Integrated Systems).
•
•
SeaTalk cable, optional, with SeaTalk connector(s) at one or both ends.
NMEA Output cable, optional, with an NMEA OUT connector at one
end only.
Power Cable
Thedisplaysystem(i.e.withascannerconnected)isintendedforuseonships’
DC power systems rated at 12V, 24V or 32V.
A 5 ft. (1.5 m) power cable is supplied for connecting the ship’s DC power to
the display unit. Longer power cable runs may require larger wire gauges to
minimise any voltage drop in the cable.
Ifalongerpowercablerunisrequired, usethesuppliedpowercabletoconnect
to the display unit. Then use a suitable connector block to connect the free end
to the extension cable, taking particular care to ensure correct polarity. The
2
supplied power cable has a cross-section of 2.0 mm .
Download from Www.Somanuals.com. All Manuals Search And Download.
6-10
SL520/530/631 PLUS Chartplotter Displays
6.5 Mounting the Display Unit
The display unit is waterproof to CFR46 and can be installed either above or
below deck. The display unit can be mounted using the mounting bracket
supplied, or console mounted using the optional flush-mounting kit (see
Section 6.2).
Mounting Bracket
The display unit can be mounted on a dash, chart table, bulkhead or deckhead.
Figure 6-6: Display Mounting
1. Loosen the knobs and remove the mounting bracket from the display unit.
2. Mark the locations of the mounting bracket screw holes on the mounting
surface.
3. Use the screws supplied to attach the mounting bracket at the marked loca-
tions.
4. Attach the display unit to the mounting bracket, adjust the display angle
and tighten the knobs.
Console Mounting
The display unit can be console mounted if required, using the optional flush-
mounting kit (M92708 or E55033).
CAUTION:
Make sure there are no hidden electrical wires or other items behind the
location before proceeding. Make sure there is sufficient rear access for
mounting and cabling.
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 6: Installation
6-11
1. A clear, flat area of the following dimensions is required:
Display
Width
Height
Depth behind Panel
7” Mono Display
7” Color Display
10.4” Color Display
9 in (230 mm)
9 in (230 mm)
11.75 in (300 mm)
8¼ in (210 mm)
8¼ in (210 mm)
11.6 in (295 mm)
6 in (152 mm)
6.9 in (176 mm)
6.4 in (162 mm)
2. Unpack the flush-mounting kit.
3. Using the supplied template, trace out the display unit opening.
4. Drill a ½ in (12.7 mm) pilot hole in each corner of the cut-out area.
5. Using a suitable saw, cut along the inside edge of the cut-out line.
6. Remove the mounting bracket knobs and bracket from the display unit.
Make sure that the unit fits in the cut-out area.
If the optional screw fitting is required, drill four 3/16 in (5 mm) holes as
indicated on the template.
Screw the studs into the holes provided at the rear of the display.
7. Connect the DC power cable, inter-unit cable, and any other accessory
cables to the display. Avoid tight bends in the cables.
8. Place the gasket on the unit and slide the unit into the panel cut-out.
9. Use the flush-mounting kit to secure the unit to the console.
Alternatively, place a spacer over each of the four studs and secure with
the thumb nuts.
Download from Www.Somanuals.com. All Manuals Search And Download.
6-12
SL520/530/631 PLUS Chartplotter Displays
6.6 System Connections
Grounding the System
It is important that an effective RF ground is connected to the system. You
must ground the display by connecting the drain wire (shield) of the Power/
NMEA Input cable to the ship’s RF ground; a single ground point should be
used for all equipment.
If you need to extend the wire, the extension wire should be an 8 mm braid or
2
AWG 10 (6.0 mm ) multi-stranded cable.
If your vessel does not have an RF system, connect the drain wire to the
negative battery terminal.
DC Power Connection
The display is intended for use on ships’ DC power systems rated at 12 V,
24 V or 32 V.
The power connection to the display should be made at either the output
of the battery isolator switch, or at a DC power distribution panel.
Raymarine recommends that power is fed directly to the display via its
own dedicated cable system and MUST be protected by a thermal circuit
breaker or fuse, installed close to the power connection.
The DC system should be either:
•
Negative grounded, with the negative battery terminal connected to the
ships ground.
•
Floating, with neither battery terminal connected to the ships ground.
CAUTION:
This system is not intended for use on “positive” ground vessels.
The power cable Ground (earth) connections must be connected to the
ship’s ground as described above.
Power for External Equipment
External equipment cannot be powered from the display’s SeaTalk
interface.
It must be powered from the ship’s supply or via a SeaTalk bus.
Refer to Section 6.8 for further details.
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 6: Installation
6-13
Display Unit Connection
The rear of the display provides the following connection sockets:
•
•
•
SeaTalk, for SeaTalk data input and output.
NMEA Output, for NMEA data output in an integrated system.
Power/NMEA Input, for 12 V, 24 V or 32 V DC power connection, two
NMEA 0183 inputs and one RF ground (screen) connection.
To NMEA instruments
To SeaTalk
instruments/GPS
POWER/NMEA
TRANSDUCER
SeaTalk
NMEA
OUT
R
G
Y
NMEA IN 1
NMEA IN 2
POWER IN
D6112-1
Figure 6-7: Chartplotter Display Connector Panel
The following sections detail the display unit connectors used when installing
a display. The remaining connector details are provided in Section 6.8.
Download from Www.Somanuals.com. All Manuals Search And Download.
6-14
SL520/530/631 PLUS Chartplotter Displays
Power and NMEA Input Connection
The DC power and NMEA input should be connected at the rear Power/
NMEAseven-pinconnector. Theconnector(viewedfromtheoutside)andpin
functions are shown in the following diagram and table. The NMEA Input is
detailed in Section 6.8.
f
2
5
7
6
1
4
3
Pin No. Function
Color
1
2
3
4
5
6
7
Channel 1 NMEA data input (+ve)
Orange
Yellow
Channel 1 NMEA return (-ve)
Battery negative
Black
Shield (drain wire)
No insulation
Battery positive (12/24/32 V systems) Red
Channel 2 NMEA data input (+ve)
Channel 2 NMEA return (-ve)
Green
Blue
Figure 6-8: Power and NMEA Connector
Power Connection
CAUTION:
If the power connections are accidentally reversed the system will not
work. Use a multimeter to ensure that the input power leads are
connected for correct polarity.
Switch off the display unit before you remove the power cord.
The RED wire must be connected to the feed from the positive (+) battery
terminal and the BLACK wire to the feed from the negative (–) battery
terminal. The shielded wire (screen) should be connected to the ship’s RF
ground as previously described in Grounding the System on page 6-12.
Any unused wires should be insulated and taped back.
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 6: Installation
6-15
6.7 System Checks and Inital Switch On
Once you have installed your Chartplotter and made all the connections, you
need to check your installation and perform the System Checks before using
the system for navigation. It is strongly recommended that the System Checks
are performed before connecting the display to other equipment in an
integrated system. If you encounter any problems, refer to Chapter 7.
You may wish to read Chapters 2 to 4, and familiarise yourself with the
operation of the system, before performing the initial set up and alignment.
System Check
Before performing the functional test, check the following:
•
All securing bolts are fully tightened and mechanical locking arrange-
ments as specified are in place.
•
•
All connections have been made.
All connecting wires are secured and protected as necessary.
Note: If you are the boat owner and have performed the installation yourself,
ask your authorised installation dealer to check the installation before going
to sea.
Switch On and Initial Setup
To switch on the display unit, press and hold the POWER key until the unit
beeps.
If necessary, adjust the lighting (see Changing the Lighting & Contrast -
SL520 Mono Display on page 2-4 or Changing the Brightness - SL530/631
Color Display on page 2-5).
If required, change the default language settings as follows:
1. Press the MENU key to display the setup soft keys.
SYSTEM
SET UP¬
CHART
SET UP¬
TRACK
SET UP¬
GPS
SETUP¬
D4162-1
2. Press the SYSTEM SET UP soft key.
The SYSTEM SET UP menu is displayed, listing the parameters and their cur-
rent settings. The complete list, which you can scroll down, is shown in the
following illustration.
Download from Www.Somanuals.com. All Manuals Search And Download.
6-16
SL520/530/631 PLUS Chartplotter Displays
SYSTEM SET UP MENU
DATA BOXES
BEARING MODE
CURSOR REFERENCE
CURSOR READOUT
DAY/NIGHT
TRUE
RELATIVE
RNG/BRG
RNG/BRG
ON
HELP
SOFT KEYS
ON
KEY BEEP
ON
MOB DATA
DR
MENU TIMEOUT PERIOD NO TIMEOUT
DISTANCE UNITS
SPEED UNITS
NAUTICAL MILES
KNOTS
DEPTH UNITS
METRES
TEMPERATURE UNITS
VARIATION SOURCE
CENTIGRADE
AUTOMATIC
BRIDGE NMEA HEADING ON
NMEA-OUT SET UP
CURSOR ECHO
DATE FORMAT
TIME FORMAT
TIME OFFSET
GPS SOG COG FILTER
COMPASS SET UP
LANGUAGE
DD/MM/YY
24 HOUR
UTC
MEDIUM
ENGLISH (US)
OFF
D3650-6
SIMULATOR
Figure 6-9: System Set Up Menu
3. Use the trackpad to move the selection bar down to the LANGUAGE option.
The soft key labels are updated.
4. Use the soft keys to highlight the required language.
5. Press ENTER to return to the setup soft keys.
6. Press CLEAR to return to the normal screen.
EMC Conformance
Always check the installation before going to sea to make sure that it is not
affected by radio transmissions, engine starting etc.
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 6: Installation
6-17
6.8 Integrated Systems
The displays can be linked to other equipment to transfer data as follows:
•
•
•
Data can be received via SeaTalk or NMEA, some of which will increase
the functionality of the display. Other data can be viewed on the display.
Data can be transmitted via SeaTalk and NMEA to enhance other equip-
ment.
Some incoming data can be converted across the communication link and
re-transmitted - see Data Conversion on page 6-23.
Power for External Equipment
External equipment cannot be powered from the display’s SeaTalk
interface. It must be powered from the ship’s supply or via a SeaTalk bus.
Ensure correct polarity of the SeaTalk connection.
For systems where the ship’s power source is 24 V only, you may need to
install a 24 V to 12 V DC converter. This is only necessary if the products
being connected to the display are:
•
SeaTalk compatible (for example, compass, GPS and instruments), and
there is no existing SeaTalk bus
•
NMEA compatible, but operate only from 12 V (for example, compass,
GPS and some navigators)
The DC~DC converter must conform to the following specification:
Table 6-2:
DC-DC Converter for External Equipment
Input
21 to 32 V DC
Output 13.6 V DC, isolated
Load
Continuous current rating, in excess of required load
Download from Www.Somanuals.com. All Manuals Search And Download.
6-18
SL520/530/631 PLUS Chartplotter Displays
®
SeaTalk and NMEA In
The display can receive a comprehensive range of data. The primary data is
described below:
Table 6-3:
Function of SeaTalk and NMEA Data
Data
Primary Uses
Suggested Source
Heading
Heading Modes
Autopilot,
MOB (if Speed data also available)
Compass connected to SeaTalk bus
NMEA Compass*
Position
MOB(alsorequiresspeedandHDG SeaTalk GPS connected via Auxiliary JB
data)
Existing GPS Navigator via SeaTalk bus
Existing GPS (or Loran-C) navigator with
NMEA output
Position data in data box and Nav
Window
Waypoints
Own vessel position
Data Log
Waypoint
Waypoint transfer
Existing GPS Navigator via SeaTalk bus
Existing GPS (or Loran-C) navigator with
NMEA output
Heading data should ideally contain both magnetic and true heading. If only
one is available then variation needs to be provided either manually or
automatically - see Variation Source on page 5-8.
Some other radars and chartplotters can exchange their cursors via SeaTalk.
Locked heading should be used for Course Up if available via SeaTalk.
Otherdataconnected viaaSeaTalkbusorviaNMEAisgenerally displayed in
data boxes, e.g. depth, apparent wind angle and speed, time.
Note: The Raymarine Fishfinder uses its own depth data, rather than any oth-
er depth data on SeaTalk. If there is no other depth data on SeaTalk, Fishfind-
er depth is transmitted. If speed and temperature data are available on
SeaTalk the Fishfinder uses this data; if this data is not on SeaTalk from other
instruments, it is transmitted by the Fishfinder.
For details of received data refer to the table in Appendix C:SeaTalk and
NMEA Data Received and Transmitted.
SeaTalk
The SeaTalk standard was originally developed by Autohelm (part of
Raymarine), and allows compatible instruments to be connected by a single
cable carrying power and data in/out. This means that additional instruments
and functions can beadded to aSeaTalk system, simply bypluggingthem into
the network.
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 6: Installation
6-19
SeaTalk is a precise, high-speed, bi-directional protocol which is flexible
enough to adapt to any number of instruments, without a central processor.
SeaTalk equipment can also communicate with non-SeaTalk equipment via
the NMEA standard.
SeaTalk Connection
SeaTalk data, if present, is the primary source for all navigational data except
heading.
The SeaTalk input/output should be connected at the rear SeaTalk 3-pin
connector. This appears as follows, when viewed from outside:
SeaTalk In/Out
1. Red (No internal connection)
2. Screen (0V)
3. Yellow (Data)
D3232-3
Figure 6-10: SeaTalk Connector
Table 6-4:
Sea Talk Connections
Pin No.
Function
+12 V
0 V
Color
Red
1
2
3
Shield
Yellow
Data
Note:
1. IfyouusetheSeaTalkconnectoryoumustfitthesuppliedferritetothecable
for EMC CE conformance. The ferrite must be clipped to the cable as close to
the connector as possible.
2.Thedisplaydoesnotsupply12VviatheSeaTalkconnector, neitherdoesthe
SeaTalk connector require 12 V to operate.
12 V is required for other SeaTalk units.
3. If you are connecting an active compass, the NMEA input has priority. You
should, therefore use an NMEA input channel (see Power and NMEA Input
Connection) rather than the SeaTalk interface, unless the compass only has a
SeaTalk output.
To connect the display unit to the SeaTalk bus, connect a standard SeaTalk
cable between the SeaTalk connector on the rear of the display and a SeaTalk
instrument or the SeaTalk bus.
Download from Www.Somanuals.com. All Manuals Search And Download.
6-20
SL520/530/631 PLUS Chartplotter Displays
Standard SeaTalk cables are available in a range of lengths (part numbers
W284 to W287), and cables for connecting to SeaTalk units with round
connectors are also available (part numbers D187 or D188), see Section 6.2
for further details.
NMEA 0183
The NMEA 0183 Data Interface Standard was developed by the National
MarineElectronicsAssociationofAmerica. Itisaninternationalstandardthat
enables equipment from many different manufacturers to be connected
together and to share information.
The information is passed in “sentences”, each of which has a three-letter
sentence identifier. When you check to see if one item will “talk” to another,
make sure that the two items both use the same sentence identifiers. For
example: VTG carries Course and Speed Over Ground data; GLL carries
angle and wind speed data.
TheNMEA 0183 standardcarriessimilarinformationtoSeaTalk. However, it
has the important difference that one cable will only carry information in one
direction. For this reason NMEA 0183 is generally used to connect a data
receiver and a transmitter together: for example, a compass sensor
transmitting heading to a radar, or a GPS sensor (or Chartplotter) transmitting
position and navigation data to a radar.
NMEA Input Connection
The two NMEA/Power input connectors are normally used for non-SeaTalk
Compass (heading) data or GPS. It can also be used for additional navigation
data (if not provided via SeaTalk).
Connect the input(s) to the orange and yellow wires (Channel 1) and/or the
green and blue wires (Channel 2). Refer to Power and NMEA Input
Connection on page 6-14 for further details.
For example, to connect a Raymarine Heading Sensor to the NMEA
Channel 1 input, connect the cables and power supply using a suitable
connector block, as shown in the diagram below. If installed, it may be
convenient to connect the power to the SeaTalk auxiliary junction box
described in the following section.
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 6: Installation
6-21
Red
+12 V
Yellow
Black
+ NMEA Data (orange)
-- NMEA Data (yellow)
0V
D3604-1
Figure 6-11: NMEA Input Connection
Using the SeaTalk Auxiliary Junction Box
A junction box (provided with the chartplotter display) is used to connect the
SeaTalk systemto the display unit. This junction box enables the SeaTalk bus,
power and GPS to be connected.
If power is not already available (via another SeaTalk instrument), the
applications. The junction box may also be used for other purposes, e.g.
supplying power to a flux gate compass and routing the compass data to the
display NMEA In connection, or alternatively, for connecting a NMEA GPS
system.
The junction box includes:
•
•
•
•
SeaTalk cable and connector to attach to display unit
Power cable to connect to 12 V power (if required)
Input connections to connect SeaTalk cable from external equipment
Spare connections for another instrument
CAUTION:
Ensure correct polarity of the 12 V supply before applying SeaTalk
power. It is recommended that a multimeter is used to check the
connections.
Figure 6-12 shows how to connect the junction box; for details specific to
your GPS, refer to the handbook supplied.
Download from Www.Somanuals.com. All Manuals Search And Download.
6-22
SL520/530/631 PLUS Chartplotter Displays
To GPS
Power Out: 1 & 2
Power In: 1 & 3
To Display Unit
SeaTalk Socket
12V
Power
Supply
Spare
Input
Fused
Cable
SeaTalk
Black (screen)
Function
0V
+12v
SeaTalk
0V
+12V
0V
+12V
SeaTalk
1
2
3
1
2
1
2
3
Red
Yellow
Black (screen)
Red
Black (screen)
Red
Power
GPS
Yellow
D4291-1
Figure 6-12: Using the Auxiliary Junction Box
Data Output
Data is transmitted in SeaTalk and NMEA formats as detailed in Appendix D
and can be used to enhance other equipment as required. You can disable the
transmission of individual NMEA output sentences - refer to NMEA Out Set
Up on page 5-9.
The SeaTalk input/output connection is detailed in SeaTalk Connection on
page 6-19.
The NMEA output connector is a 4-pin connector as illustrated below. The
1.5 m NMEA OUT cable has a ferrite clamp attached to ensure EMC
conformance.
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 6: Installation
6-23
NMEA OUT connector
NMEA OUT connector
Pin Pin name Function
2
3
4
5
NMEA_GND
NMEA_SIG
N/C
NMEA ground
NMEA data output
N/C
Pin 2, white
Pin 5, screen
CGND
Screen
Pin 3, blue
Pin 4, not connected
*Pin 1 does not exist on this connector
3
2
Rear of display
NMEA out
5
4
D4254_1
Figure 6-13: NMEA Output Connector
Data Conversion
The displays convert some information across the communications links as
follows:
NMEA In to NMEA Out and SeaTalk
SeaTalk to NMEA Out
This enables data received by the display to be passed to other instruments.
You can prevent NMEA heading data being bridged onto the Seatalk bus -
refer to Bridge NMEA Heading on page 5-8.
Note: To transfer NMEA data, orto convert the data, the display mustbe pow-
ered On.
Download from Www.Somanuals.com. All Manuals Search And Download.
6-24
SL520/530/631 PLUS Chartplotter Displays
6.9 Integrated System Checks
Chart Display
When you have connected your display unit to the required equipment ensure
that position data is available at the display via NMEA or SeaTalk.
To confirm your chartplotter is operating correctly, perform the following
checks:
1. Without a chart card installed, select the Chart display mode and select a
suitable range scale. Verify that the world map is visible.
Use the trackpad to check cursor movement and normal scrolling action.
2. To ensure that the display is responding to position data:
PressFINDSHIP, check the cursor is fixed onthevesselsymbolwhich is cor-
rectly positioned at the center of the chart display.
3. Insert a chart cartridge for the area of your vessel.
Use the RANGE key to zoom-in to check that the chart data is being dis-
played.
Received Data
If either SeaTalk or NMEA In is connected, verify that the expected data is
displayed.
1. Press DISPLAY and select the NAV DATA WINDOW ON.
Check that the expected data is displayed.
2. If heading data is connected, select Chart mode and check it is displayed in
the heading data box .
Transmitted Data
If SeaTalk or NMEA Out is being transmitted to other equipment, check that
the data is being received correctly.
An NMEA Out connector is used to transmit navigation data. The NMEA
Outputcableshouldbeconnectedtotheupper, leftconnectorontherearofthe
display unit.
Note: The NMEA Output cable has a ferrite clamp attached to ensure EMC
conformance.
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 7: Maintenance and Problem Solving
7-1
Chapter 7: Maintenance and Problem
Solving
This chapter provides information on routine maintenance and on possible
causes of problems you may experience with your display unit.
7.1 Maintenance
WARNING:
The display unit contains high voltage. Adjustments require specialized
service procedures and tools only available to qualified service
technicians - there are no user serviceable parts or adjustments and the
operator should not attempt to service the equipment. The operator
should not remove the rear cover of the display.
Switch off the display unit before removing the power cord.
Routine Checks
The display is a sealed unit. Maintenance procedures are therefore limited to
the following periodic checks:
•
•
•
Wipe the display clean with a damp cloth (ensure power is off).
Examine the cables for signs of damage, such as chafing, cuts or nicks.
Check that the cable connectors are firmly attached.
Cleaning Instructions - SL530/631 PLUS Color Display
Cleaning the Display
CAUTION:
Take care when cleaning the display. Avoid wiping the display screen
with a dry cloth - this could scratch the screen coating.
Do not use acid, ammonia based or abrasive products.
•
•
Ensure power is off, wipe the display clean with a damp cloth.
If necessary, use IPA (iso-propyl alcohol) or a mild detergent solution to
remove grease marks.
EMC Servicing and Safety Guidelines
•
Raymarine equipment should be serviced only by authorized Raymarine
service technicians. They will ensure that service procedures and replace-
ment parts used will not affect performance. There are no user serviceable
parts in any Raymarine product.
Download from Www.Somanuals.com. All Manuals Search And Download.
7-2
SL520/530/631 PLUS Chartplotter Displays
•
•
Some products generate high voltages, so never handle the cables/connec-
tors when power is being supplied to the equipment.
When powered up, all electrical equipment produces electromagnetic
fields. These can cause adjacent pieces of electrical equipment to interact
withoneanother, withaconsequentadverseeffectonoperation. Inorderto
minimise these effects and enable you to get the best possible performance
from your Raymarine equipment, guidelines are given in the installation
instructions, to enable you to ensure minimum interaction between differ-
ent items of equipment, i.e. ensure optimum Electromagnetic Compatibil-
ity (EMC).
•
•
Always report any EMC-related problem to your nearest Raymarine
dealer. We use such information to improve our quality standards.
In some installations, it may not be possible to prevent the equipment from
being affected by external influences. In general this will not damage the
equipment but it can lead to spurious resetting action, or momentarily may
result in faulty operation.
7.2 Resetting the System
There are three types of reset available for the display:
•
FactoryReset:Thisresets allvaluesback to theiroriginalfactory settings.
CAUTION:
The factory reset clears the Waypoints and Routes databases.
•
Power-On Reset: When you turn the display off and on again, the screen
reverts to the chart picture with all windows cleared.
•
Picture Reset: Press and hold the DISPLAY key for two seconds to return
the screen to the full-screen picture of the top window with all windows
cleared.
At power-on, the last-used values are retained for all the options, except for
those listed in the following table which are reset to the factory default each
time.
Table 7-1:
Power On Default Settings
Item
Power-on setting
Heading Mode
Alarm
Windows
North Up
ON, with last-used value
OFF
Lighting & contrast (mono
display)
Lighting 40%, contrast 50%
Brightness (Color Display))
ON at 100%.
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 7: Maintenance and Problem Solving
7-3
➤ To perform a factory reset:
1. Press MENU.
2. Press the SYSTEM SET UP soft key to display the System Set Up page (see
Section 5.3 for details).
3. Press and hold MENU for 5 seconds.
A countdown timer is displayed. If you release the MENU key before the
timer reaches zero, the reset is not performed.
When the reset request has been accepted, the system restarts.
The factory default settings are listed in Section 5.3
7.3 Problem Solving
All Raymarine products are, prior to packing and shipping, subjected to
comprehensive test and quality assurance programs. However, if this unit
should develop a fault, please refer to the following table to identify the most
likely cause and the corrective action required to restore normal operation.
If you still have a problem after referring to the table below, contact your local
dealer, national distributor or Raymarine Technical Services Department for
further advice.
Always quote the product serial numbers. The display unit serial number is
printed on the back of the unit.
Common Problems and Their Solutions
Table 7-2:
Common Problems
Problem
Correction
Display does not function
1. Make sure that the power supply cable is sound and that
all connections are tight and free from corrosion.
2. Check the system fuse.
Technical Support:
Please visit out website at:
www.raymarine.com/recreational/support
where you willfind aQuestions &Answersdatabase, serviceinformationand
e-mail access to the Technical Support department.
Alternatively, if you don’t have access to the world wide web, call:
1-800-539-5539 extension 2444 or
(603) 881-5200 extension 2444
Our Technical Support Specialists are available to answer questions about
installing, operating and trouble-shooting all Raymarine products.
Download from Www.Somanuals.com. All Manuals Search And Download.
7-4
SL520/530/631 PLUS Chartplotter Displays
How to Contact Raymarine (US)
For Marine Product and Services Information
Visit the Raymarine World Wide Web site for the latest information on the
newest Raymarine electronic equipment and systems at:
www.raymarine.com
For Accessories and Parts
Many Raymarine accessory items and parts can be obtained directly from
your authorized Raymarine dealer. However, if you are in need of an item not
available from the retailer, please contact Raymarine Technical Services at:
1-800-539-5539 extension 2333 or (603) -881-5200.
Technical Service is available Monday through Friday 8:15 AM to 5:00 PM
Eastern Standard Time.
Please have the Raymarine item or part number ready when calling if placing
anorder. Ifyouare notsurewhichitemisappropriateforyourunit, youshould
first contact the Technical Support Department at:
1-800-539-5539 ext. 2444 or
(603)-881-5200 to verify your requirements.
For Product Repair and Service
In the unlikely event your Raymarine unit should develop a problem, please
contact your authorized Raymarine dealer for assistance. The dealer is best
equippedtohandleyourservicerequirementsandcanoffertimesavinghelpin
getting the equipment back into normal operation.
In theeventthatrepairscan notbeobtainedconveniently, productservicemay
also be obtained by returning the unit to:
Raymarine Product Repair Center
22 Cotton Road, Unit D
Nashua, NH 03063-4219
The Product Repair Center is open Monday through Friday 8:15 a.m. to
5:00 p.m. Eastern Standard Time or Eastern Daylight Savings Time. All
products returned to the Repair Center are registered upon receipt. A
confirmation letter will be sent to you acknowledging the repair status and the
product’sreferencenumber. Shouldyou wishtoinquire abouttherepairstatus
of your unit, contact the Product Repair Center at:
1-800-539-5539
Please have the product reference number, or unit serial number, ready when
you call. We will do everything possible to make the repair and return your
unit as quickly as possible.
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 7: Maintenance and Problem Solving
7-5
How to Contact Raymarine (Europe)
In Europe, Raymarine support, service and accessories may be obtained
from your authorised dealer, or contact:
Raymarine Company
Anchorage Park, Portsmouth
PO3 5TD, England
Tel +44 (0)23 9269 3611
Fax +44 (0)23 9269 4642
Or visit the Raymarine World Wide Web site:
www.raymarine.com
Accessories and Parts
Raymarine accessory items and parts are available through your authorized
Raymarine dealer. Please refer to the lists of component part numbers and
optional accessories in the Installation chapter of this manual, and have the
Raymarine part number ready when speaking with your dealer.
Ifyouareuncertainaboutwhatitemto chooseforyourRaymarineunit, please
contact our Customer Services Department prior to placing your order.
Worldwide Support
Please contact the authorized distributor in the country. A list of worldwide
distributors is supplied with your system.
Download from Www.Somanuals.com. All Manuals Search And Download.
7-6
SL520/530/631 PLUS Chartplotter Displays
Download from Www.Somanuals.com. All Manuals Search And Download.
Appendix A: Specification
A-1
Appendix A:Specification
SL520/530/631 PLUS Displays
General
Approvals:
CE - conform to
1999/5/EC, EN60945:1997
FCC - conforms to
Part 80 (47CFR) and Part 2 (47CFR)
Size:
7”mono
7” color
10.4” color
223 x 204 x 75mm (8.8" x 8" x 3"), excluding bracket
223 x 205 x 152 mm (8.8" x 8.1" x 6"), excluding bracket
292 x 289 x 139 (11.5” x 11.4” x 5.46), excluding bracket
Weight
7”mono
7” color
10.4” color
1.2 kg(2.6lbs)
3.5 kg (7.7 lbs)
5.75 kg (12.65 lbs)
Mounting
Power
Bracket with panel mount option
External 10.7 - 44 V DC required
Floating earth/fully isolated
7"mono
7” color
10.4” color
10 W consumption with full backlighting
20 Wmax. consumption with full brightness
30W max.consumption with full brightness
Environmental:
Waterproof to CFR46; suitable for external mounting
Op/Storage Temp. Range -mono -10°C to +70°C
- color
Humidity limit
-10°C to +50°C
up to 95% at 35°C non-condensing
Controls
11 defined keys, 4 soft keys and trackpad
Cursor
Context sensitive, provides range/bearing or lat/lon
Display Type: - mono
7" Film Super Twist Neumatic (FSTN) LCD, monochrome with
4 gray scales
color TFT LCD
- color
Resolution: 7"mono
320 x 240 (1/4 VGA)
640 x 480 (VGA)
7”& 10.4” color
Display Size 7"mono
7" color
7" diagonal - 143 mm x 111 mm
136 mm x 100 mm
10.4”
211 mm x 154.4 mm
Mono LCD Contrast
Languages
100 levels, selectable via soft keys.
UK English, US English, Danish, French, German, Dutch, Ital-
ian, Icelandic, Norwegian, Portuguese, Spanish, Swedish,
Finnish
Connectors
3 pin SeaTalk input/output
4 pin NMEA output7 pin power including 2 NMEA input chan-
nels
Download from Www.Somanuals.com. All Manuals Search And Download.
A-2
SL520/530/631 PLUS Chartplotter Displays
Interfaces
1 x SeaTalk, receive and transmit
1 x NMEA 0183, transmit
2 x NMEA 0183, receive
C-MAP cartridge reader - 2 slots
Cursor Echo
Cursor Echo between radar and chart on separate displays
connected via SeaTalk.
Man Overboard
(MOB Mode)
Mark placed with course line; readout shows range, bearing,
lat/lon of MOB and time elapsed since MOB.
Screen Functions
Data Boxes
Full, half and quarter screens available dependent on function
Up to six user selectable information boxes
Chartplotter Features
Cartography
C-MAP® NT micro cartridges available from C-MAP®
Chart of the world built in
Display Windows
Chart Scaling
Chart, Data Log, BDI, CDI, Navdata
1/64 nm (if cartographic data is available) to 4000 nm
North up (selectable True or Magnetic) Head up or Course up
Presentation Modes
Waypoints
1000waypointsenteredviacursor, lat/lon, rangeandbearingfrom
present position or at vessels position.
16 character name can be assigned
Additional storage available on User Cartridges
Waypoint Transfer
Routes
Current route via Seatalk, NMEA
A route plan may contain up to 50 waypoints. Up to 20 routes can
be stored in the units internal memory
Additional storage available on User Cartridges
SmartRoute to create a route from a track history
Track History
5 tracks with up to 750 points in each can be stored in the units
internal memory
Additional storage available on User Cartridges
Alarms
Programmable arrival, cross track error, anchor drift, grounding,
position fix/data loss warning, countdown timer and alarm clock
Navigation Information
Own ships position in Lat/Lon, XTE, TTG and SOG/COG selectable.
Mileagescaleruler.Bearinganddistancetowaypoint. Bearingand
distance to cursor, SeaTalk data (see ‘interfacing’ section)
Variation Source
Auto (SeaTalk/NMEA/Internal algorithm) or Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
Appendix A: Specification
A-3
Interfacing
SeaTalk Input
Depth, Speed Over Ground & Course Over Ground, Position,
Waypoint number, range, bearing and time to go, Speed through
water, Time, Cross Track Error, Heading, Wind, Date, Log/Trip, Pilot
Status, Temperature, Man Overboard, and cursor position
NMEA Input
NMEA 0183 (GLL, GGA, GLC, GTD, VTG, BWC, BWR, RMA, RMB,
RMC, XTE, VHW, HDG, HDM, HDT, DBT, DPT, APB,VLW, MWV,
MTW,WPL, RTE and ZDA)
SeaTalk Output
Cursor data, Guard zone alarm and Navigational data bridged
from NMEA
NMEA Output
(User selectable)
APB, BWC, BWR,DBT, DPT,GGA, GLL, MTW, RMA, RMB, RMC, RSD,
TTM, VLW, VHW, VTG, WPL, ZDA
Download from Www.Somanuals.com. All Manuals Search And Download.
A-4
SL520/530/631 PLUS Chartplotter Displays
Download from Www.Somanuals.com. All Manuals Search And Download.
Appendix B: C-MAP Chart Card Features
B-1
Appendix B:C-MAP Chart Card Features
TheC_MAP chartcardsdisplay cartographicfeatures which arederivedfrom
a library of symbols. The library includes a set of 16 x 16 pixel bitmaps which
provide realistically shaped icons for many chart objects. However, these
complexicons can overlap and clutterthedisplay at somescales, soitpossible
for the user to select smaller, simple icons. Some chart objects are represented
by text; in such cases conventional abbreviated text is used, for example, M –
mud, R – rock, Wk – wreck
Thechartplottersetupmenuprovidesthesub-menuCUSTOMISECHART,which
lets you determine how chart features are displayed. You can set the icon
display of many features to custom; you then use the CUSTOM soft key to
switch the customized icons off/on. The factory default for the CUSTOM
options is on.
The chart features controlled from the Customize Chart menu are grouped as
detailed below, some groups are sub-divided into categories
Menu Option
Chart Features
Names
CHART TEXT
CHART BOUNDARIES
SPOT SOUNDINGS
DEPTH SHADING LIMIT
DEPTH CONTOURS
Chart Boundaries
Spot Soundings
Reference Depth
Depths (Bathymetric Lines)
Depth Labels
DEPTH CONTOUR DIS-
PLAY
Depth Contour
Range
NAV MARKS
Lights:
Buoys and Beacons:
Signals
Light;
Buoy, cardinal
Anchor
Light moire’ effect;
Light float;
Light vessel
Buoy, installation
Buoy, isolated danger
Buoy, lateral
Cairn
Chain/Wire
Fog signal
Buoy, safe water
Buoy, special purpose
Buoy, generic
Beacon, cardinal
Beacon, isolated dan-
ger
Beacon, lateral
Beacon, safe water
Beacon, special pur-
pose
Radar reflector
Top mark
Nav aid, generic
Extended nav- aid,
generic
Radar station
Radar transponder bea-
con
Radio station
Beacon, generic
LIGHT SECTORS
Light Sectors
Download from Www.Somanuals.com. All Manuals Search And Download.
B-2
SL520/530/631 PLUS Chartplotter Displays
Menu Option
Chart Features
CAUTION & ROUTING
DATA
Caution Areas
Caution area
Fishing facility
Marine farm/cul-
ture
Tracks and Routes
Deep water route part
Deep water route cen-
terline
Fairway
Cable, submarine
Cable area
Offshore prod’n
area
Ferry route
Navigation line
Precautionary area
Radar line
Pipeline
Radar range
Pipeline area
Anchor berth
Anchorage area
Cargo tranship-
ment area
Contiguous zone
Continental shelf
area
Custom zone
Dumping ground
Exclusive economic
zone
Fishery zone
Fishing ground
Free port area
Harbour area
(administrative)
Incineration area
Log pond
Radio calling
Recommended route
centerline
Recommended track
Recommended traffic
lane part
Traffic separation line
Traffic separation
scheme boundary
Traffic separation
scheme crossing
Traffic separation
scheme lane part
Traffic separation
scheme roundabout
Traffic separation
zone
Two-way route part
National territorial
area
Sea area
Spoil ground
Straight territorial
sea baseline
Submarine transit
lane
Territorial sea area
Restricted area
Sea Plane landing
area
Military practice
area
MARINE FEATURES
Tideways & Cur-
rents
Tideway
Water turbulence
Tide height
Seabed bottom
Sand waves
Seabed area
Spring
Weed/Kelp
Download from Www.Somanuals.com. All Manuals Search And Download.
Appendix B: C-MAP Chart Card Features
B-3
Menu Option
Chart Features
LAND FEATURES
Natural Features
Coastline
Dune
Cultural Features
Airport area
Built-up area
Railway
Road crossing
Road part
Building, religious
Building, single
Cemetery
Fortified Structure
Siloway route part
Tank
Hill
Land elevation
Land region
Land
Runway
Chimney
Salt pan
Slope topline
Tree
Vegetation area
Natural Features -
Rivers
Sloping ground
Square
Cable, overhead
Fence
Pipeline, overhead
Pylon
Telepheric
Dish aerial
Flagstaff/flagpole
Flarestack
Mast
Monument
Radar dome plane land-
ing area
Canal
Canal bank
Rapids
Tunnel entrance
Tower
Windmill
River
Windmotor
River bank
Waterfall
Lake
Lake shore
ICON DISPLAY
Complex (detailed) object/Simple object
Download from Www.Somanuals.com. All Manuals Search And Download.
B-4
SL520/530/631 PLUS Chartplotter Displays
The following chart features are always displayed:
Menu option
Chart features
PORTS
Ports:
Services
Port Information
Berthing facility
Causeway
Checkpoint
Crane
Coastguardstation Port area
Pilot boarding
place
Harbour master
Coast Guard
Police
Rescue station
Dam
Signal station, traf- Customs
Distance mark
Dock area
Dry dock
fic
Health emergency
Post office
Yacht club
Signal station,
warning
Dyke area
Dyke crown
Floating dock
Gate
Boat yard
Accessories
Electrical/electronic
repairs
Gridiron
Harbour facility
Hulk
Landing place
Landing stairs
Lock basin
Oil barrier
Pile
Engine repairs
Sailmaker
Fishing/diving gear,
SCUBA
Hotel/Inn
Restaurant
Bank/Exchange office
Pharmacy
Pontoon
Ramp
Port/Marina
Slipway
Shoreline construction
Slipway
Boat hoist
Crane
Weir
Small craft facility
Fuel station
Water
Electricity
Showers
Launderette
Public toilets
Post box
Public telephone
Refuse bin
Visitor’s berth
Chandler
Provisions
Bottle gas
Car Parking
Parking for boat and trail-
ers
Caravan site
Camping site
Sewerage pump-out sta-
tion
CARTOGRAPHIC
OBJECTS
Line, generic
Area, generic
NATURAL FEATURES
Land area
Bridge
Download from Www.Somanuals.com. All Manuals Search And Download.
Appendix B: C-MAP Chart Card Features
B-5
The following chart features are always displayed:
Menu option
ROCKS
Chart features
Underwater Rock
Wrecks
WRECKS
DEPTHS 1
DEPTHS 2
DEPTHS 3
PORTS
Depth area
Dredged area
Intertidal area
Mooring/Warping facility
Fish haven
CAUTION AREAS
OFFSHORE INSTALLA-
TIONS
Diffuser
Obstruction
Production installation
Offshore platform
AREAS, LIMITS
No data area
CARTOGRAPHIC
OBJECTS
Incomplete survey area
NATURAL FEATURES (Ice) Ice area
Pingo
COMPOSITE OBJECTS
Airport
Anchorage
Channel edge
Deep water route
Defined water
Harbour
Range system
Lighthouse
Mooring trot
Navigation mark, afloat
Navigation mark, fixed in point
Traffic Separation Scheme Sys-
tem
CARTOGRAPHIC AREAS
Cartographic II25 area
Download from Www.Somanuals.com. All Manuals Search And Download.
B-6
SL520/530/631 PLUS Chartplotter Displays
Download from Www.Somanuals.com. All Manuals Search And Download.
Appendix C: SeaTalk and NMEA Data Received and Transmitted
C-1
Appendix C:SeaTalk and NMEA Data
Received and Transmitted
The following table defines the data received on the NMEA/SeaTalk ports.
Data sources are listed in order of priority except where indicated.
Data Received
Source
Position (LAT/LON)
Position (Loran C TD’s)
Speed and Course Over Ground
Waypoint Data
SeaTalk, GGA, RMC, RMA, GLL
GLC, RMA, GTD
SeaTalk, RMC, RMA, VTG
SeaTalk, RMB, APB, BWC, BWR, RMB, XTE
SeaTalk, DBT, DPT
Depth
Apparent Wind Angle and Speed
Boat Speed Through Water
Total Log and Trip Log
Water Temperature
Average Boat Speed through the Water
Heading
SeaTalk, MWV (relative)
SeaTalk, VHW
SeaTalk, VLW
SeaTalk, MTW
SeaTalk only
SeaTalk, HDG, HDM, HDT, VHW
SeaTalk only (Autopilot / Steering Compass)
SeaTalk, RMC, RMA, HDG
SeaTalk only
Locked Heading
Magnetic Variation
Rudder Angle (not displayed)
Time (No priority)
SeaTalk, ZDA, GGA, RMC, GLL, BWC, BWR
SeaTalk, ZDA, RMC
Date
MOB data
SeaTalk only
Autopilot Status (Standby / Auto / Vane / Track) SeaTalk only
Cursor Range and Bearing (from Chartplotter)
Cursor Range and Bearing (from Radar)
SeaTalk only
SeaTalk, RSD
Global Alarms - Watch alarm, Wind alarm,
Autopilot alarms, Depth alarms.
Waypoint arrival
SeaTalk Only
SeaTalk, RMB, APB
SeaTalk, WPL, RTE
Waypoint/Route Transfer
*If Magnetic Headingis notavailable, the True HeadingandVariation(if available) are usedto
generate the magnetic heading.
Download from Www.Somanuals.com. All Manuals Search And Download.
C-2
SL520/530/631 PLUS Chartplotter Displays
The display unit transmits the following data, if available, on SeaTalk:
Data Output
SeaTalk
NMEA Out
GGA, GLL, RMC, RMA
RMA
Position (LAT/LON)
Position (Loran C TD’s)
✔
✔
✔
,
Speed Over Ground and
Course Over Ground
RMC, VTG,RMA
Waypoint Data
✔
RMB, APB, BWC, BWR
Depth
✔
Apparent Wind Angle and Speed
Boat Speed Through Water
Total Log and Trip Log
Water Temperature
Heading
✔
—
—
✔
✔
✔
✔
VHW
RMA, RMC
ZDA
Magnetic Variation
Time
✔
✔
Date
✔
ZDA
MOB data
✔
—
2
Cursor Range & Bearing
Heading mode
✔
RSD
2
—
—
SeaTalk
RSD
Waypoint/Route Transfer
WPL, RTE
Global Alarm
—
Waypoint Arrival Alarm
APB, RMB
4
Bridged from NMEA if selected in the System Set Up menu.
Download from Www.Somanuals.com. All Manuals Search And Download.
Appendix D: Abbreviations
D-1
Appendix D:Abbreviations
A
Amp
ANSI
AWG
American National Standards Institute
American Wire Gauge
BDI
Brg
Bearing and Distance Indicator
Bearing
CCFL
CD
Cold Cathode Fluorescent Lamp
Course Deviation Indicator
Code of Federal Regulations
Course Made Good
Course Over Ground
Cathode Ray Tube
CFR
CMG
COG
CRT
CTR
Center
dB
deciBels
DC
DMG
DR
Direct Current
Distance Made Good
Dead Reckoning
EBL
EMC
ETA
Electronic Bearing Line
Electro Magnetic Compatibility
Estimated Time of Arrival
FCC
FLT
ft
Federal Communication Commission
Float - floating EBL/VRM
feet
FTC
Fast Time Constant
GPS
Global Positioning System
differential Global Positioning System
Guard Zone
dGPS
GRD
GHz
Giga Hertz
HDG
Hz
Heading
Hertz
MHz
Mega Hertz
IEEE
in, "
Institute of Electrical & Electronic Engineers
inch
Kg
kW
kilogram
kilo Watt
lat
lbs
latitude
pounds
Download from Www.Somanuals.com. All Manuals Search And Download.
D-2
SL520/530/631 PLUS Chartplotter Displays
LCD
lon
Liquid Crystal Display
longitude
M
m
Magnetic
meters
MBS
mm
Main Bang Suppression
millimeter
MOB
MRK
Man OverBoard
Mark
nm
nautical mile
NMEA
National Marine Electronics Association
POS
Position (of vessel)
RF
Rng
rpm
Radio Frequency
Range
Revolutions Per Minute
SSB
SHM
SOG
STC
Single Side Band
Ships Heading Marker
Speed Over Ground
Sensitivity Time Control
T
True
TFT
TTG
Thin Film Transistor
Time To Go
V
Volts
VHF
VMG
VRM
Very High Frequency
Velocity Made Good
Variable Range Marker
WPT
XTE
yds
Waypoint
Cross Track Error
yards
ZMB
Zoom Box
Download from Www.Somanuals.com. All Manuals Search And Download.
Index
xiii
Index
North Up 5.12
A
Simulator 2.1, 2.3, 5.10
Chart Grid
On and Off 2.10
Chart Master 1.2
Chartplotter
Accessories 6.4
Adding
a Waypoint to a Route 3.18, 3.28
Alarm Clock Alarm 4.4
Alarms
Alarm Clock 4.4
Anchor 4.4
Arrival 3.31, 4.4
Countdown Timer 4.4
External 4.4
Grounding 4.4
MOB 4.6
Off Track 4.4
Display Options 1.5
Features 1.5, A.2
Radar/Chart Synch 5.11
CLEAR Key 1.10
Setting 4.1, 4.5
ALARMS Key 1.10, 4.4, 4.5
Anchor Alarm 4.4
Arrival Alarm 3.31, 4.4
Autopilot Pop Up 5.7
Autopilot Pop-Up 5.4
B
Clearing
the Current Route 3.18, 3.23
Backlight Control 2.4
BDI
Window Options 1.4
Bearing Mode 5.4, 5.6
Bridge NMEA Heading 5.5, 5.8, 6.23
Brightness Adjustment 2.5
Brightness Control 2.5
C
Cable Runs 6.9
Installation Considerations 6.2
Cables
Connections 6.12
Power & NMEA In 6.13, 6.14, 6.20
Context-sensitive Cursor 1.9, 2.12
Deleting Items 1.9
NMEA 6.9
Power 6.9
Contrast Adjustment 2.4
Control Functions
SeaTalk 6.9
Chartplotter 2.12
Cancel
Conventions Used 2.1
Countdown Timer Alarm 4.4
Course Up 5.12
MOB 4.7
CDI
Window Options 1.4
Center the Chart 1.5, 2.12
Chart
Creating a Route 3.18
by Placing Waypoints 3.19
from a Track 3.37, 3.41
Using the Waypoint List 3.20
Cross Track Error - See XTE
Current Route 3.18
Altering 3.29
Center 1.5, 2.12
Data 3.2
Nearest 3.7
Object Information 3.4, 5.11, 5.13
Port 3.4, 3.5
Clearing 3.18, 3.23
Source 3.4
Cursor 1.8
Tide 3.4, 3.5
Context-sensitive 1.9, 2.12
Data Box 2.10
Definition 1.2
Mode
Goto 3.29, 3.33
Full Screen 2.6
Moving 1.9
Download from Www.Somanuals.com. All Manuals Search And Download.
xiv
SL520/530/631 PLUS Chartplotter Displays
Readout 5.4, 5.6
Reference 5.4, 5.6
Cursor Echo 4.1, 4.7, 5.5, 5.9
Chart 4.7, 5.9
Local 4.7, 5.9
Radar 4.7, 5.9
SeaTalk 4.7, 5.9
Custom Options
Chartplotter 1.6, 2.11
Customizing
the Chart Display 5.11
the Screen Presentation Options 2.10
D
Data Box 2.10, 5.4, 5.6
COG 5.4
Cursor 2.10
Date 5.4
Depth 5.4
Group of Six 2.10
On/Off 2.11
Deleting
Heading 5.4
List of 5.4
Log/Trip 5.4
MOB 4.6, 5.4
Moving 1.9, 2.11
On/Off 2.11
Pilot 5.4
Position 5.4
Ruler 4.2, 4.3
SOG 5.4
Speed 5.4
Temperature 5.4
Tide Set/Drift 5.4
Time 5.4
Lighting 2.4, 2.5
VMG 5.4
Waypoint 5.4
Wind 5.4
Operating Modes 1.4
Selecting 2.6
Set Up Options 1.3
XTE 5.4
DISPLAY Key 1.4, 1.10, 2.6, 2.7, 4.10
Data Conversion 6.23
Data Display 3.25
Chart Object 3.4, 5.11, 5.13
Nearest 3.7
Display Options
Chartplotter 1.5
Display Unit 1.iii
Connections 6.13
Port 3.4, 3.5
Console Mounting 6.10
Contrast Adjustment 2.4
Grounding 6.12
Lighting Adjustment 2.4
Location 6.5
Source 3.4
Tide 3.4, 3.5
Route 3.18, 3.24
Data from other Equipment 4.1, 4.6, 6.23
COG 4.1
Mounting 6.10
Specification A.1
Heading 1.4, 4.1, 4.6, 5.8
NMEA 4.1, 6.20
Position 1.4, 4.1, 4.6
SeaTalk 4.1, 4.7, 6.18
Speed 4.6
Switching Off 2.2, 2.3
Switching On 6.15
Displaying
Chart Data 3.3
Waypoint Data 3.8, 3.12, 3.25
Data Log Mode 1.4, 4.1, 4.10
Full Screen 2.6
Download from Www.Somanuals.com. All Manuals Search And Download.
Index
xv
Installation
E
Editing
EMC Conformance 6.16
Integrated System 6.17
Location 6.2, 6.5
a Route 3.18, 3.27
Using the ST60/80 Navigator Keypad 3.17
Waypoint Details 3.8, 3.13
EMC
Conformance 1.vi, 6.16
Servicing and Safety Guidelines 7.1
ENTER Key 1.10
Erasing
Items On-Screen 1.9
J
a Route 3.18, 3.26
a Waypoint 3.8, 3.14
External Alarms 4.4
F
Junction Box
K
Factory Reset 7.2
Features
Key Beep 5.4, 5.7
Keys
L
Chartplotter 1.5, A.2
Display 1.3
Find Ship 2.12, 2.13
Follow
a Route 3.29
Route Options 3.29, 3.31
Stop 3.29, 3.33
Functions
Chartplotter 1.7
G
Key 2.5
Goto
a Target 3.29, 3.32
a Waypoint 3.29, 3.32
Cursor 3.29, 3.33
Stop 3.29, 3.33
GPS
Log/Trip Data Box 5.4
Loran TDs 3.11
M
Positional Accuracy 4.8
Restart GPS 4.9
Set Up 4.1, 4.8
GPS SOG/COG Filter 5.5, 5.10
H
Maintenance 7.1
Make and Follow a Route Scenario 2.20
Managing Tracks 3.37
MARKS Key 1.10, 3.9, 3.12, 3.35, 3.36, 4.6
Master Display
Half Screen Windows 1.4, 2.6
Definition 1.2
Selecting 2.7
Measuring Distances Using the VRM/EBL Key
4.1, 4.2
Head Up 5.12
Heading 5.5, 5.8, 6.23
Heading Data 1.4, 4.1, 4.6, 5.8
Heading Data Box 5.4
Heading Mode 5.12
Heading Vector 5.11, 5.13
Help 5.4, 5.7
MENU Key 1.10, 2.3, 3.37, 4.8, 5.1, 5.2
Menu Timeout 5.4, 5.7
MOB 4.1
Alarm 4.6
Cancel 4.7
Data Box 4.6, 5.4
Data Selection 5.7
Symbol 4.6
Help from Raytheon
Europe 7.5
US 7.4
Waypoint 4.6
High Voltage 1.iii
Modes
Chart 2.6
I
Data Log 1.4, 2.6, 4.1, 4.10
Identifying Objects
with Cursor Echo 4.7
Full Screen 2.6
Download from Www.Somanuals.com. All Manuals Search And Download.
xvi
SL520/530/631 PLUS Chartplotter Displays
Mounting the Display Unit 6.10
Console Mounting 6.10
Moving
Position
Position Offset 5.11, 5.14
Power
a Data Box 1.9, 2.11
a Waypoint 3.8, 3.14, 3.18, 3.27
the Cursor 1.9
MULTI Key 1.10, 2.5
N
Naming
for External Equipment 6.12, 6.17
R
a Route 3.18, 3.22, 3.26
a Track 3.39
a Waypoint 3.8, 3.13, 3.17
Using the ST60/80 Navigator Keypad 3.17
Nav Data
Window Options 1.4
Navigation Aid 1.iii
Navigator Keypad 3.8, 3.15
NMEA 1.4
Radar Display
Cable 6.9
Data 4.1, 6.20
Heading 5.5, 5.8, 6.23
Input Connection 6.13, 6.18, 6.20
Output Connection 6.13, 6.22, 6.24
NMEA Out Set Up 5.5, 5.9
North Up 5.12
Remote Cursor Echo
O
Object Information - Chart 5.11, 5.13
Restart
Displaying 3.4
GPS 4.9
Off Track Alarm 4.4
Offsetting the Center 1.5
Operating Controls
Cursor 1.8
Database List 1.8, 1.12
Dedicated Keys 1.3, 1.8, 1.10
Pop-up Menus 1.8, 1.11
Soft Keys 1.3, 1.8, 1.10, 5.4, 5.7
Trackpad 1.3, 1.8, 2.12
Operating Modes 1.4
Chart 2.6
Review Your Passage Plan Scenario 2.22
Route
Clearing 3.18
Creating 3.18
Creating from a Track 3.37, 3.41
Current 3.18
Data Display 3.18, 3.24
Database List 3.15, 3.18, 3.22, 3.23, 3.25
Editing 3.18, 3.27
Data Log 2.6, 4.1, 4.10
Plotter 2.15, 5.11, 5.12
Selecting 2.6
Using the ST60/80 Navigator Keypad
3.17
Orientation - Chart 5.11, 5.12
P
Erasing 3.18, 3.26
Picture Reset 7.2
Pilot Data Box 5.4
Follow 3.29
Loading from a User Cartridge 3.34
Naming 3.18, 3.22, 3.26
NMEA Transfer 3.34
Retrieving 3.18, 3.23
Reversing 3.27, 3.28
Saving 3.18
Pilot Pop Up 5.7
Pilot Pop-Up 5.4
Place and Goto a Waypoint Scenario 2.18
Placing
a Waypoint 3.8, 3.9, 3.19
Plotter Mode 2.15, 5.11, 5.12
Pop-up Menus 1.8, 1.11
Port Data 3.4, 3.5
Saving to a User Cartridge 3.34
Transferring 3.34
Download from Www.Somanuals.com. All Manuals Search And Download.
Index
xvii
Route Leg 3.18
Stop
Data Display 3.24
Follow 3.29, 3.33
Routine Checks 7.1
Ruler Data Box 4.2, 4.3
S
Switching
Chart Grid On and Off 2.10
Safety 1.iii, 3.1
Data Boxes On/Off 2.11
EMC Guidelines 6.2, 7.1
Navigation Aid 1.iii
Saving
a Route 3.18
a Track 3.39
Range Rings On and Off 2.10
Scale
MOB 4.6
Chart 2.12, 2.13, 3.2, 4.6
Waypoint 3.8, 3.13, 5.11, 5.13
System
Scenarios
Make & Follow a Route 2.20
Place & Goto a Waypoint 2.18
Review Your Passage Plan 2.22
SeaTalk 1.4
Connections 6.12
Cable 6.9
Connection 6.13, 6.18, 6.19
Cursor Echo 5.9
Data 4.1, 4.7, 6.18
Selecting
a Half Screen Window 2.7
a Waypoint 3.8, 3.12
the Operating Mode 2.6
Servicing
EMC Guidelines 7.1
Set Up Options 1.3, 2.11
Set Up Parameters
GPS Set Up 4.9
Tide Data 3.4, 3.5
Tide Set/Drift Data Box 5.4
Seting Up
a GPS 4.9
Setting Alarms and Timers 4.1, 4.5
Setting Up
Alarm Clock 4.4
Countdown 4.4
Setting 4.1
a GPS 4.1, 4.8, 4.9
Chart Parameters 5.2, 5.11
GPS Set Up
Trackpad 1.3, 1.8, 2.12
Restart GPS 4.9
Tracks
Initial Set Up 6.15
System Parameters 5.2, 5.4
Tracks 3.37, 3.38
Simulator 5.5, 5.10
Chart 2.1, 2.3
Clearing 3.37, 3.39
Converting to Route 3.41
Database List 3.39
Managing 3.37, 3.39
Naming 3.39
Radar 2.1, 2.3
Using the ST60/80 Navigator Keypad
3.17
SmartRoute 3.41
Soft Key Labels 5.7
Soft Keys 1.3, 1.8, 1.10, 5.4, 5.7
SOG (Speed Over Ground) Data Box 5.4
Specification
Saving 3.39
Setting Up 3.37, 3.38
Transferring
a Route 3.34
Display A.1
Speed Data 4.6
Speed Data Box 5.4
ST60/80 Navigator Keypad 3.8, 3.15, 3.17
Status Bar 1.5
a Waypoint 3.8, 3.18, 3.34
U
Units 5.4, 5.7
User Cartridge 3.34
Download from Www.Somanuals.com. All Manuals Search And Download.
xviii
V
Variation Source 5.5, 5.8
Vectors 5.11, 5.13
VMG Data Box 5.4
VRM/EBL Key 1.10, 4.1, 4.3
W
Warranty 1.v
Waypoint 5.11, 5.13
Adding to a Route 3.18, 3.28
Data Box 5.4
Data Display 3.8, 3.12, 3.25
Database List 3.8, 3.9, 3.13, 3.14, 3.19, 3.32
Editing 3.8
Editing Details 3.13
Erasing 3.8, 3.14
Goto 3.29, 3.32
Loading from a User Cartridge 3.34
MOB 4.6
Moving 3.8, 3.14, 3.18, 3.27
Naming 3.8, 3.13
Numbers 5.11, 5.13
Placing 3.8, 3.9, 3.19
Position 3.8, 3.13
Removing from a Route 3.18, 3.28
Saving to a User Cartridge 3.34
Selecting 3.8, 3.12
Symbol 3.8, 3.13, 5.11, 5.13
Target 3.29, 3.32
Transferring 3.8, 3.18, 3.34
Transferring on NMEA 3.34
Transferring on SeaTalk 3.34
Waypoint List
Creating a Route 3.20
Wind Data Box 5.4
Window Options
BDI 1.4
CDI 1.4
Full Screen 1.4
Half Screen 1.4, 2.6
Nav Data 1.4
World Map 1.5, 3.2
X
XTE (Cross Track Error)
Data Box 5.4
Restart 3.29, 3.32
Z
Zoom 1.5
Download from Www.Somanuals.com. All Manuals Search And Download.
Warranty Certificate
The Raymarine warranty terms and conditions as described below do not affect the customer’s statutory rights.
Limited Warranty
Raymarine warrants each new Light Marine Product to be of good materials and workmanship. Raymarine, or
it’s approved agents, will repair or exchange under warranty any parts proven to be defective in material or
workmanship under normal use, for a period of 2 years/24 months from date of sale to end user, or 30 months
from date of shipment from Raymarine – whichever expires first, except as provided below.
Raymarine Limited Warranty covers the parts and labor associated with any warranty repair as described
above, provided that the unit is returned to Raymarine or one of it’s appointed agents.
Installed Warranty
In addition to the Limited Warranty cover as described above, Raymarine will, except as provided below,
cover travel costs (auto mileage and tolls) up to 100 round trip highway miles (160 kilometers) and travel time
of 2 hours, to enable onboard warranty service to be carried out on products where proof of installation or com-
mission by Raymarine certified installers, can be shown.
The Installed Warranty provides for onboard repair or exchange, by Raymarine or it’s approved service
agents, for a period of 2 years/24 months, from date of sale of the boat to the end user – where the equipment
has been installed by a Raymarine certified installer, or from commissioning of the installation by a Raymarine
certified installer, or 30 months from date of shipment of the equipment from Raymarine – whichever expires
first, except as provided below.
Obtaining Warranty Service
In the event of Warranty service being required, contact Raymarine or the nearest Raymarine certified service
agent – a full list of local service agents are available on the Internet or can be requested from the nearest Ray-
marine agent.
A suitable proof of purchase, showing date, place of purchase, and serial number must be made available to
Raymarine or authorized service agent at the time of request for Warranty service.
In cases where a Raymarine certified installer has not installed the product; i.e. Limited Warranty, the
affected unit must be returned to the local Raymarine approved service agent, with a copy of proof of purchase
and/or completed warranty card. Subject to the Limitations below, the unit will be repaired/replaced at no fur-
ther cost to the user and promptly returned to the user.
In cases where the equipment has been installed by a Raymarine certified installer (boat builder, installer
dealer etc.), i.e. Installed Warranty, the nearest local service agent should be contacted and onboard service
requested, the warranty card, correctly completed and stamped by the installing agent, must be available as
authorization for onboard service.
Warranty Limitations
Raymarine Warranty policy does not apply to equipment that has been subjected to accident, abuse or misuse,
shipping damage, alterations, corrosion, incorrect and/or non-authorized service, or equipment on which the
serial number has been altered, mutilated or removed.
Raymarine assumes no responsibility for damage incurred during installation or as a result of improper instal-
lation.
This Warranty does not cover routine system checkouts, alignment/calibration, sea-trials or commissioning,
unless required by replacement of part(s) in the area being aligned.
A suitable proof of purchase, showing date, place, and serial number must be made available to Raymarine or
authorized service agent at the time of request for Warranty service.
Consumable items, (such as: fuses, batteries, drive belts, radar mixer diodes, snap-in impeller carriers, impel-
lers, impeller bearings, and impeller shaft) are specifically excluded from this Warranty.
All costs associated with transducer replacement, other than the cost of the transducer itself, are specifically
excluded from this Warranty.
Overtime/premium labor portion of services outside of normal working hours is not covered by this Warranty.
Continued . . .
Download from Www.Somanuals.com. All Manuals Search And Download.
Travel cost allowance on certain products with a suggested retail price below $2500.00 is not authorized.
When/or if repairs are necessary, these products must be forwarded to a Raymarine facility or an authorized
dealer at owner’s expense and then will be returned via surface carrier at no cost to the owner.
Travel costs other than auto mileage, tolls and two (2) hours travel time, are specifically excluded on all prod-
ucts. Travel costs, which are excluded from the coverage of this Warranty, include but are not limited to: taxi,
launch fees, aircraft rental, subsistence, customs, shipping and communication charges etc. Travel costs, mile-
age and time, in excess to that allowed must have prior approval in writing.
TO THE EXTENT CONSISTENT WITH STATE AND FEDERAL LAW:
(1) THIS WARRANTY IS STRICTLY LIMITED TO THE TERMS INDICATED HEREIN, AND NO
OTHER WARRANTIES OR REMEDIES SHALL BE BINDING ON RAYMARINE INCLUDING WITH-
OUT LIMITATION ANY WARRANTIES OF MERCHANTABLE OR FITNESS FOR A PARTICULAR
PURPOSE.
(2) Raymarine shall not be liable for any incidental, consequential or special (including punitive or multiple)
damages.
All Raymarine products sold or provided hereunder are merely aids to navigation. It is
the responsibility of the user to exercise discretion and proper navigational skill inde-
pendent of any Raymarine equipment.
Document number: 84066-9
July 2002
Download from Www.Somanuals.com. All Manuals Search And Download.
Factory Service Centers
United States of America
UK, Europe, Middle East, Far East
Raymarine Inc
22 Cotton Road,Unit D
Nashua, NH 03063-4219, USA
Raymarine Ltd
Anchorage Park, Portsmouth
PO3 5TD, England
Telephone: +1 603 881 5200
Fax: +1 603 864 4756
www.raymarine.com
Telephone: +44 (0)23 9269 3611
Fax: +44 (0)23 9269 4642
www.raymarine.com
Sales & Order Services
Telephone: +1 800 539 5539 Ext. 2333 or
+1 603 881 5200 Ext. 2333
Customer Support
Telephone: +44 (0)23 9271 4713
Fax: +44 (0)23 9266 1228
www.raymarine.com
Technical Support
Telephone: +1 800 539 5539 Ext. 2444 or
+1 603 881 5200 Ext. 2444
www.raymarine.com
Product Repair Center
Telephone: +1 800 539 5539 Ext. 2118
Stick barcode label here
Purchased from
Dealer address
Purchase date
Installed by
Installation date
Commissioned by
Commissioning date
Owner’s name
Mailing address
This portion should be completed and retained by the owner.
Download from Www.Somanuals.com. All Manuals Search And Download.
Download from Www.Somanuals.com. All Manuals Search And Download.
|