Raritan Engineering Marine Sanitation System PST02 User Guide

®
PURASAN  
(Models PST*02 and PST*03 [*specify 12,24,32] Manufactured after September, 2004)  
OPERATION, MAINTENANCE AND INSTALLATION INSTRUCTIONS  
THE FOLLOWING ARE CAUTIONARY STATEMENTS THAT MUST BE READ AND  
FOLLOWED DURING BOTH INSTALLATION AND OPERATION  
WARNING: Raritan Engineering Company, Inc. recommends that a qualified person or electrician install this product.  
Equipment damage, injury to personnel or death could result from improper installation. Raritan Engineering  
Company, Inc. accepts no responsibility or liability for damage to equipment, or injury or death to personnel  
that may result from improper installation or operation of this product.  
WARNING: HAZARD OF SHOCK AND FIRE  
Always use recommended fuse or circuit breaker and wire size.  
WARNING: HAZARD OF FLOODING - When leaving the boat unattended always be sure seacocks are closed. Any  
installation made below waterline should have double hose clamps securing lines. The halogen disinfectant is  
corrosive to aluminum, copper and steel. The plumbing system must not include any aluminum, copper  
or steel fittings, piping or holding tanks.  
IMPORTANT SAFETY INSTRUCTIONS FOR HANDLING PURASAN® TABLETS AND SOLUTION  
WARNING: HAZARD OF DANGEROUS CHEMICAL REACTION  
1. Use ONLY Purasan Tablets.  
2. DO NOT add any other chemicals or cleaning products to the toilet or the treatment system. Raritan C.P. - Cleans  
Potties and R.C. Raritan Concentrate are the only factory-recognized cleaning product that may be used in the  
toilet.  
WARNING: HAZARD OF SEVERE INJURY  
1. DO NOT allow tablets to come in contact with skin, eyes or clothing. If contact occurs, immediately wash  
affected area with fresh water. Remove and wash any affected clothing.  
2. Use a well ventilated area when handling Purasan Tablets. DO NOT breathe dust from tablets - severe damage to  
mucous membrane of the respiratory passages could occur.  
3. Do not ingest.  
4. Follow all cautions and warnings associated with handling of tablets.  
5. When reloading the Tablet Dispenser, ventilate area well and wear chemical resistant protective gloves and eye  
protection.  
6. DO NOT ATTEMPT TO REFILL EMPTY CARTRIDGES.  
The Purasan is a U. S. Coast Guard Certified Type I Marine Sanitation Device for use on inspected and  
uninspected vessels 65 feet and under. It must be operated within areas that are not declared a Federal No  
Discharge Zone (NDZ) by the U.S. Environmental Protection Agency (EPA). This is applicable for all U.S.  
territorial waters inside the three mile limit. Other countries - check with local authorities.  
The Purasan is designed for recreational use and accommodates most marine toilets it can be used with one or,  
in some cases, two toilets. The Purasan is available in 12, 24 or 32 V DC.  
The system consists of a Treatment tank, Tablet dispenser and Switch panel with cable. A portion of incoming  
water passes over the halogen tablets creating a solution that is then dispensed into the treatment tank and mixes  
with the macerated waste sanitizing it for discharge.  
1-800-352-5630  
1
Download from Www.Somanuals.com. All Manuals Search And Download.  
Use ONLY Purasan Tablets.  
DO NOT add any other chemicals or cleaning  
products to the toilet or the treatment system.  
Raritan C.P. - Cleans Potties and R.C. Raritan  
Concentrate are the only factory-recognized cleaning  
products that may be used in the toilet.  
MAINTENANCE  
WARNING: Read and understand all safety  
instructions (including Material Safety Data  
sheet) for handling Purasan Tablets before  
performing any work on the Purasan.  
Recommended Visual Inspection  
INSTALLING TABLET CARTRIDGE  
Tablet level in cartridge monthly  
Tubes to and from dispenser are unobstructed  
Tubes to treatment tank are unobstructed  
Replace tablet cartridge only when completely empty.  
Clean or replace tubes if any obstruction is found.  
REPLACING TABLET CARTRIDGE  
(#41-135)  
CAUTION: Tablet dispenser may be under pres-  
sure. Open lid SLOWLY  
Remove used tablet cartridge -  
1. With adequate ventilation available - Unscrew  
tablet dispenser lid and lift out used tablet car-  
tridge.  
2. Rinse thoroughly with water to remove any re-  
sidual tablet particles.  
3. Clean plug assembly  
CAUTION: Never dispose of tablets in a dry state  
refer to MSDS for proper disposal.  
4. Dispose of empty cartridge with other recyclable  
plastics.  
Loading new tablet cartridge in dispenser  
1. Hold new tablet cartridge over tablet dispenser  
with large end down. Remove tablet cartridge cap  
and allow any loose tablet particles to drop into  
the tablet dispenser. Slide tablet cartridge down  
into tablet dispenser.  
2. Cut nipple off top of tablet cartridge to create  
an air hole.  
3. Replace lid on tablet dispenser.  
CLEANING: Do not add any other chemicals or  
cleaning products to the toilet or the treatment system.  
3
Download from Www.Somanuals.com. All Manuals Search And Download.  
Tablet Dispenser  
1. Close flow metering clamp and disconnect power  
to water solenoid, if used, to prevent intake wa-  
ter from entering tablet dispenser.  
Close  
Remove  
and drain  
2. Flush toilet and activate treatment cycle several  
times to leave just water in tank.  
3. Carefully remove small tube from white “T”  
fitting or check valve from water solenoid valve.  
Drain tube into a clean plastic container.  
step 1  
4. Carefully remove the small tube at the bottom of  
the black “T” fitting. Drain tube into a clean plas-  
tic container.  
step 3  
5. Connect Tube removed in step 3 to black “T”  
fitting  
Remove  
and drain  
6a. White “T’ fitting:  
Connect tube removed in step 4 to white “T”  
6b. Water Solenoid Valve  
Connect  
tube  
plug tube removed in step 4  
shut off water to valve  
removed  
in step 3  
step 4  
drain water from valve, hoses and strainer  
7. Take solution collected in plastic container and  
pour into toilet bowl. Rinse container and dis-  
pose of properly.  
Connect tube  
removed in step 4  
step 5  
8. Flush toilet several more times to dilute solution  
and clear it from system.  
Treatment Unit  
WARNING: DO NOT use anti-freeze of any kind  
to winterize the Purasan system.  
1. Turn off power and disconnect wires to Purasan  
step 6a  
plug tube  
removed in  
step 4  
2. Close seacocks.  
3. Slowly open crossover plug  
Caution: Open plug slowly if treatment tank is at  
the lowest point water will spill out  
step 6b  
crossover plug  
4. Using a pump, remove water from both sides of  
the treatment tank through crossover cap.  
5. Disconnect and drain hoses.  
Winterizing the Toilet - Follow the instructions in  
the Owner’s Manual for that particular toilet.  
IMPORTANT: If toilet requires anti-freeze or other  
chemicals for winterizing, DO NOT allow these  
chemicals to enter the Purasan system.  
4
Download from Www.Somanuals.com. All Manuals Search And Download.  
Recommissioning  
IMPORTANT:  
• Do not load Tablet Cartridge into Dispenser until system is  
powered and operational.  
• Do Not Operate Purasan until Treatment Unit is filled with  
water.  
Treatment Tank  
1. Reconnect hoses and open seacocks.  
2. Reconnect wires and turn power on.  
NOTE: Purasan treatment tank must be full before activating a cycle.  
IMPORTANT: Do Not connect Tablet Dispenser at this time.  
3. Fill the treatment tank:  
• Single button operation - Remove crossover plug from  
Treatment Unit and fill with a minimum of three gallons of  
water, replace crossover plug and O-ring.  
• Independent operation - flush toilet allowing three gallons of  
water to pass into Purasan  
4. Turn on power to Purasan.  
5. Check for leaks.  
Reconnecting the Tablet Dispenser  
IMPORTANT  
• Make sure everything is working properly before proceeding.  
• These instructions are the reverse operation outlined in winterizing  
the Tablet Dispenser, steps 3 through 6.  
1. Remove tube from the bottom of the black “T” fitting and re-  
attach to the white “T” fitting or solenoid valve.  
2. Reconnect hose on tank to the black “T” fitting on dispenser.  
START UP  
1. Remove Crossover Cap from treatment unit tower. Pour 3  
gallons (11.5 liters) of water into Treatment Unit. Replace  
Crossover Cap.  
2. Turn on power to unit.  
3. Fill toilet bowl half full of water before beginning.  
4. Close metering clamp completely, then open slightly.  
5. Flush toilet. Check water level in Tablet Dispenser during flush  
cycle. Water level should rise to water line marked on Tablet  
Dispenser while toilet is flushed, then drain out.  
6. Adjust clamp until water reaches the line; opening clamp allows  
more water into Tablet Dispenser. Flush toilet each time clamp  
adjustment is changed to be sure water continues to be at the  
proper level.  
7. Load Tablet Cartridge.  
5
Download from Www.Somanuals.com. All Manuals Search And Download.  
U.S.C.G. Type I MSD Certification #159.015/106/0  
Maximum Roll/Pitch Angle: 30°  
Maximum Temperature Exposure: 120° F (49° C)  
Maximum Total Flush Volume: 1.5 gallons/flush (5.7 liters/flush)  
Water - fresh, salt or brackish  
NOTES: for Wiring  
1.  
2.  
Distances are from source to unit and back to source.  
Recommended conductor wire minimum AWG (mm2) for 3% voltage drop.  
Recommended conductor sizes are based on 105oC rated insulation.  
Refer to ABYC Standards for other insulation ratings.  
3.  
Recommended Wire and Fuse/Circuit Breaker Size  
Units  
Circuit  
Amp. draw  
@ nominal  
voltage  
Voltage Breaker/fuse  
size (amps)  
10  
15  
20  
25  
30  
40  
50  
feet  
feet  
feet  
feet  
feet  
feet  
feet  
12 VDC  
24 VDC  
32 VDC  
20  
15  
15  
10  
8
12 AWG 12 AWG 10 AWG 10 AWG 10 AWG 8 AWG  
6 AWG  
14 AWG 14 AWG 14 AWG 12 AWG 12 AWG 10 AWG 10 AWG  
14 AWG 14 AWG 14 AWG 14 AWG 14 AWG 12 AWG 12 AWG  
8
CONVERSIONS  
Wire - AWG to mm2  
Fuse Specifications  
AWG 16  
14  
12  
10  
8
6
4
2
12 VDC  
Fuse type  
24 VDC  
Fuse type  
32 VDC  
Fuse type  
mm2  
1.5  
2.5  
4.0  
6.0  
10.0 16.0 25.0 35.0  
Maximum amperage Maximum amperage Maximum amperage  
part number  
part number  
part number  
Feet to Meters  
MDL 6 1/4  
5 amp draw  
32-218  
MDL 6 1/4  
4 amp draw  
32-218  
MDL 5  
4 amp draw  
34-218  
FUSE 1 (F1)  
Mixer Motor  
Feet  
10  
15  
20  
25  
30  
40  
50  
MDL 12  
5 amp draw  
42-220  
MDL 6 1/4  
4 amp draw  
32-218  
MDL 5  
4 amp draw  
34-218  
FUSE 2 (F2)  
Macerator Motor  
Meter 3.1  
4.6  
6.1  
7.6  
9.2  
12.2 15.2  
SWITCH PANEL  
DIMENSIONS  
TREATMENT UNIT DIMENSIONS  
TABLET DISPENSER  
DIMENSIONS  
7 ¼”  
(18.4cm)  
2 ¼”  
(5.7cm)  
6” (15.2cm)  
Diameter  
3 3/8”  
3 ¾”  
c/c  
(8.6cm)  
(9.5cm)  
9 ¾”  
(24.8cm)  
Width:  
Depth:  
16" (40.6cm)  
8 ¾" (22.3cm)  
6
Download from Www.Somanuals.com. All Manuals Search And Download.  
MOUNTING  
Treatment Tank  
Treatment Unit Mounting  
WARNING: DO NOT locate in an area where  
ambient temperature exceeds 120o F (49o C).  
1. Locate top of treatment tank at or below  
discharge of toilet and within six feet (1.5 m).  
Note: If mounting treatment tank higher  
than discharge. Contact Raritan  
2. Make and secure mounting frame to flat  
surface.  
3. Secure tank to frame using 3/4" (1.9 cm)  
mounting straps.  
Crossover Plug  
E  
INTAK
m)  
Mounti
Straps
not  
Note: Placing a 3/8" (.9 cm) rubber pad under tank  
will help to reduce vibration and noise.  
include
7"  
(17.8 cm)  
Mo
Switch Panel  
Note: Cable supplied is 12 feet.  
1. Locate in head compartment where indicator  
lights will be visible.  
2. Using template provided, mark the cutout for  
the panel.  
3. Route cable between Switch Panel and  
Purasan Treatment Unit.  
4. Attach wires per wiring section to back of  
switch panel.  
5. Mount panel using 4 screws. Apply a bead of  
nonpermanent sealant around rear edges of  
panel if located in shower area.  
Purasan Tablet Dispenser  
15” or  
higher  
1. Locate bottom of Tablet Dispenser a minimum  
of 15” (38 cm) above the top surface of the  
Treatment Unit or top of vented loop (if used).  
2. Locate Tablet Dispenser with a minimum of  
8” (20 cm) of clearance for removing the lid  
and periodically changing the cartridge.  
Note: Supplied tubing to connect intake water  
to dispenser is 6 feet (1.8 m) in length.  
3. Attach to wall or suitable structure using 1/4”  
(6 mm) bolts.  
IMPORTANT: Do Not load Tablet Cartridge  
into Tablet Dispenser at this time. Load  
Tablet Cartridge after completing Start Up  
procedure.  
7
Download from Www.Somanuals.com. All Manuals Search And Download.  
Raw Water Toilets -  
1. Turn off power to toilet.  
2. Close intake and discharge seacocks and  
drain water from toilet system.  
Raw water toilets  
Bowl elbow with restrictor  
3. Disconnect intake hose from bowl elbow.  
4. Remove existing bowl elbow and install new  
bowl elbow supplied with Purasan.  
5. Insert the “T” fitting in the hose between the  
output of the pump and the new bowl elbow.  
Fresh Water/Manual Toilets -  
Hose clamps  
“T” Fitting  
Water supply from  
pressure side of pump  
1. Connect reducer bushing to incoming side of  
solenoid valve.  
2. Connect 1/4” nipple fitting to outgoing side  
of solenoid valve.  
3. Install supplied strainer between water source  
and solenoid  
4. Check valve MUST be installed between so-  
lenoid valve and tablet dispenser.  
Pressurized fresh water toilets  
water  
solenoid  
Check  
valve  
adapter  
Tubing with  
clamps  
restrictor  
fitting  
WARNING:  
Discharge from  
• All installations made below the waterline MUST  
be protected by installing vented loops  
• Always double clamp fittings below waterline  
• Do Not use metal fittings  
rasan to thru-hull  
NOTE: Use PTFE tape or nonpermanent thread  
sealing compound on threaded PVC fittings and  
connections. Avoid low areas in hose that would  
allow untreated waste to collect.  
INTAKE  
1. Connect discharge of toilet to one intake port.  
2. Insert plug or second toilet discharge into other  
intake port.  
Discharge from toilet to either side  
- Install plug in side not used  
3. Determine position and glue discharge elbow to  
top of tank using PVC cement.  
4. Connect discharge hose from elbow to thru hull  
fitting.  
IMPORTANT: Be certain that the discharge  
elbow is in the correct position before gluing.  
Tablet Dispenser  
IMPORTANT: 1/4” Tube to treatment tank must  
run downward with no loops, kinks or upward  
turns.  
1. Connect 1/4” tubing from the black “T” fitting at  
the dispenser (red cap) to the check valve on the  
top of the treatment unit.  
15” minimum  
to top of tank  
or vented loop  
(if used)  
2. Slide flow metering clamp onto remaining tube  
3. Install tube with flow metering clamp from White  
“T” (in raw water installation) or Solenoid valve  
(in pressurized freshwater installation) to bottom  
of tablet dispenser (black cap).  
8
Download from Www.Somanuals.com. All Manuals Search And Download.  
WIRING  
Purasan Treatment Unit  
WARNING: Hazard of Shock and Fire  
Always use proper wire, wire connectors  
and fuse/circuit breaker. See Specification  
Chart.  
+
_
Secure wire properly.  
Do not connect other appliances to Purasan  
circuit.  
Control Box  
Fuse/breaker per  
specifications  
Make sure power is off before proceeding.  
Improper wiring can damage the Circuit  
Board and void warranty.  
_
+
Battery  
NOTE: Raritan recommends that the electric  
toilet be installed for single touch operation.  
Treatment Unit  
1. Determine proper wire size from wire chart on  
specifications page.  
2. Run supply wire from source to Positive (POS)  
and Negative (NEG) terminals on Treatment tank.  
3. Fuse or circuit breaker must be installed between  
source and Purasan on positive wire.  
Control  
Switch Panel  
1. Connect cable from Switch Panel to Circuit  
Board as follows:  
S1 to S1 - red wire  
S2 to S2 - orange wire  
L1 to L1 - green wire  
L2 to L2 - white wire  
S4 to S4 - black wire  
WIRE CONNECTIONS - Not all connections will  
be made, depends on installation options chosen  
- IN Battery Negative  
S4 Black to switch panel  
S6 Orange to switch panel #2  
S2 Orange to switch panel #1  
S3 (+) external out  
S5 Auxiliary switch  
F1 - Mixer  
H1 (-) to solenoid (Toilet #1)  
L2 White to switch panel (s)  
M2+ (+) to mixer motor  
L1 Green to switch panel (s)  
M1+ (+) to macerator motor  
S1 Red to switchpanel(s)  
+IN Battery Positive  
F2 - Macerator  
9
Download from Www.Somanuals.com. All Manuals Search And Download.  
Flushing Option #1:  
"Push to Cycle" button activates both the toilet  
and treatment cycle.  
TYPICAL INSTALLATION - Flushing Option #1  
“Push to Cycle” also activates toilet -  
single toilet installation  
Note: Toilet flush time is set at 10 seconds, after  
initial 10 seconds holding the button down will  
momentarily flush the toilet.  
Small post on  
CDS to H1  
jumper wire  
with  
1. Mount Switch Panel near toilet.  
CAUTION: Use only the Raritan #CDS (fail-  
ure to do so will damage to the Control  
Board, voiding warranty).  
3 amp fuse  
2. Run 16 ga. wire from terminal H1 on Circuit  
Board to one of the small relay terminals.  
CDS  
To toilet  
positive (+)  
3. Run a wire from the other small relay terminal  
to the Positive supply from battery with a 3 amp  
fuse.  
Battery  
TYPICAL INSTALLATION - Flushing Option #2  
“Push Button” also activates Purasan -  
single toilet installation  
Flushing Option #2:  
Toilet Push Button -  
Small post on CDS  
PBS  
Flushing toilet will activate treatment cycle.  
to S2 and PBS  
Note: Toilet may be flushed as often as necessary,  
do not exceed recommended flush volume.  
3 amp  
Fuse  
1. Mount Switch Panel near toilet.  
CAUTION: Use only the Raritan #CDS (failure  
to do so will damage to the Control Board,  
voiding warranty).  
CDS  
To toilet  
positive (+)  
2. Run 16 ga. wire from small relay terminal to S2  
on Circuit board and one post of the PBS (push  
button switch)  
Battery  
TYPICAL INSTALLATION - freshwater, dual  
installation and manual toilets  
Solenoid required to supply water to tablet  
dispenser  
Freshwater, dual installation and manual  
toilets:  
Solenoid valve supplies water to  
tablet dispenser -  
1. Mount Switch Panel near toilet.  
2. Run 16 ga. wire from battery positive to one of  
the wires on the solenoid with 3 amp fuse in line.  
Battery  
3. Run 16 ga. wire from wire on solenoid not used  
to H1 on Purasan Circuit Board.  
10  
Download from Www.Somanuals.com. All Manuals Search And Download.  
TROUBLESHOOTING  
No Water to tablet dispenser  
WARNING: After the tablet dispenser  
has had water added, it contains a very  
strong halogen solution. Always wear  
protective gloves and ventilate well to  
work on tablet dispenser. Before doing  
any maintenance or repairs, follow  
WINTERIZING/STORAGE procedures  
• Clogged check valve (T-fitting #41-200)  
Clean or replace check valve  
• Clogged intake fitting to dispenser  
Clean plug assembly  
• Intake pump or solenoid valve not functioning  
Check pump or solenoid for proper operation  
• Intake tubing clogged  
clean or replace intake tubing  
• Bowl Elbow was not changed  
install bowl elbow with restrictor, supplied  
TABLET DISPENSER  
CAUTION: Tablet Dispenser may be  
under pressure open lid slowly to relieve  
pressure.  
Overflow or water level too high in dispenser  
• Metering clamp not adjusted properly  
Adjust clamp (see start up)  
• Clogged discharge fitting in tablet dispenser  
Clean plug assembly  
• Clogged Check valve (41-111)  
Clean or replace check valve  
• Tablet dispenser not mounted correctly  
Tablet dispenser must be 15” or higher from top of  
vented loop or treatment lid  
Nothing happens when button is pushed  
• Fuses blown  
Check fuses  
• Switch panel bad  
Replace switch panel  
11  
Download from Www.Somanuals.com. All Manuals Search And Download.  
41-100  
32  
43  
45  
6
49  
31  
29  
42  
22  
47  
56  
43  
64  
63  
28  
21  
50  
23  
53  
55  
7
8
18  
17  
23  
24  
23  
10  
12  
Download from Www.Somanuals.com. All Manuals Search And Download.  
PURASAN PARTS LIST  
Item Part #  
Description  
Item Part #  
Description  
50 41-110  
Vent Kit for Tablet Dispenser (Incl. #53,  
54, & 55)  
#14 Brass Flat Washer (4)  
1
1
1
2
3
6
7
8
9
32-102AW Mixer Motor 2 1/2" Dia. 12 V DC  
33-102AW Mixer Motor 2 1/2" Dia. 24 V DC  
34-102AW Mixer Motor 2 1/2" Dia. 32 V DC  
51 M31  
52 M30  
41-100  
1/4"-20 Brass Nut (4)  
31-121  
31-120  
31-106  
31-103  
31-113-3  
31-109  
Hose Fitting (2)  
Discharge Elbow 90o  
Tablet Dispenser Complete(less cartridge)  
T-Fitting (Incl. #33, 34, 37 &38)  
Treatment Unit Complete 12 V DC  
Treatment Unit Complete 24 V DC  
Treatment Unit Complete 32 V DC  
Continuous Duty Solenoid  
41-200  
Cover Hold down Bolt, 10-32 x 7/8", S/S (18)  
Motor Shaft Bushing (2)  
Motor Hold down Bolt, 10-32x1", S/S (4)  
Mixer Impeller  
42-1000  
43-1000  
44-1000  
CDS*  
10 31-110-1  
11 31-110-2  
12 31-114  
13 31-115  
14 31-122  
15 41-102  
16 31-112  
17 31-108  
18 31-107  
19 31-101W  
21 31-102  
Impeller Bolt, 12-24 x 5/8", S/S (2)  
Impeller Lock Washer, #12, S/S (2)  
Cover Hold down Nut, 10-32 (18)  
Treatment Tank  
Intake Plug  
Tank Divider  
Cover Gasket  
Macerator Set Screw  
Macerator Impeller  
Treatment Cover  
PSTDC03 Purasan Dual Control  
53 41-111  
54 31-305  
55 41-106  
56 31-325  
57 31-319  
58 41-111  
61 31-102-3  
62 31-102-4  
63 31-102-1  
64 31-102-2  
Check Valve  
2" (5cm) long 1/4" I.D. Tubing  
"T" Fitting  
Adapter  
3/8” x 1 3/4” Tubing  
Check Valve  
Mixer seal washer  
Mixer retaining ring  
Macerator seal washer  
Macerator retaining ring  
Motor Shaft Seal (2)  
22 33-101AW Macerator Motor 12 V DC  
22 34-101AW Macerator Motor 24, 32 V DC  
Pressurized Kit Part # 41-254  
23 31-305  
24 41-115  
25 31-104C  
26 31-105  
27 41-125  
28 41-130  
29 41-135  
1/4" I.D. Tubing  
Union Tee 1/4" Barbed  
Crossover Plug  
O-Ring  
Bottom Plug Assy.  
Dispenser Body (PVC)  
Cartridge (refill) PURASAN Tablets  
Note: Cartridge must be shipped in a  
separate container, call 856-825-4900.  
Slinger (2)  
"O" Ring  
Dispenser Cap  
Outlet Adapter  
O Ring  
T-Check Valve Body  
Check Valve Assy.  
T-Check Valve, Complete (33,34,37,38)  
Switch Panel Complete  
Control Cable  
190601  
31-305  
41-111  
41-261  
41-280  
PLA14  
PLA15  
PLA16  
In-line Strainer  
1/4” tubing  
Cartridge check valve  
fitting with restrictor  
hose clamps  
adapter: 1/2” MNPT X 3/4”  
adapter: 3/8” x 1/4”  
adapter: female 1/2” x 1/4”  
30 31-101-2  
31 RWS5  
32 41-131  
33 31-307D1  
34 31-307E  
37 31-307D  
38 41-205  
41-200  
39 41-350  
40 41-355  
41 31-304C  
42 32-218  
42-220  
Pump Kit Part # 41-253  
31-305  
41-200  
41-260  
PLA15  
Tubing  
T-fitting  
Bowl elbow with restrictor  
Adapter: 3/8” x 1/4”  
Flow Metering Clamp  
Fuse: F1, MDL 6 1/4 (12 V DC, 1 Req’d.)  
Fuse: F2, MDL 12 (12 V DC, 1 Req’d.)  
Fuse: F1/F2, MDL 6 1/4 (24 V DC, 2 Req’d)  
Fuse: F1/F2, MDL 5 (32 V DC, 2 Req’d.)  
Control Box w/Cover and Screws  
Standoff (4)  
Circuit Board Mounting Screw (4)  
Circuit Board, 12 V DC  
Circuit Board, 24 V DC  
Circuit Board. 32 V DC  
Electronic Control Complete*, 12 V DC  
Electronic Control*, 24 V DC  
Electronic Control*, 32 V DC  
*Incl. #43, 45, 47, 49  
32-218  
34-218  
43 41-301  
45 F41-312  
47 CH46VT  
49 42-303  
43-303  
44-303  
42-300  
43-300  
44-300  
* Specify Voltage (12, 24 and 32 VDC)  
13  
Download from Www.Somanuals.com. All Manuals Search And Download.  
IMPORTANT:  
DUAL INSTALLATION -  
“Push Button” also activates Purasan -  
Dual toilet installations require either  
independant operation of toilet and  
treatment cycle or activation from the  
toilet of the treatment cycle.  
Small post on CDS  
to S6 and PBS for  
second toilet  
Dual installations require only one  
dispenser, water to fill dispenser MUST  
be supplied using a freshwater solenoid.  
PBS  
3 amp  
Fuse  
Small post on CDS  
to S2 and PBS  
WIRING  
Switch Panel (2nd one)  
1. Connect cable from Switch Panel to Circuit  
Board as follows:  
CDS  
To toilet  
positive (+)  
S1 to S1 - red wire  
S2 to S6 - orange wire  
L1 to L1 - green wire  
L2 to L2 - white wire  
S4 to S4 - black wire  
Battery  
Freshwater Solenoid valve wiring  
Toilet activation starts treatment cycle  
Flushing toilet will activate treatment cycle.  
Note: Toilet may be flushed as often as  
necessary, do not exceed recommended flush  
volume.  
1. Mount Switch Panel near toilet.  
CAUTION: Use only the Raritan #CDS  
(failure to do so will damage to the Con-  
trol Board, voiding warranty).  
Battery  
2. Run 16 ga. wire from small relay terminal  
to S2 on Circuit board and one post of the  
PBS (push button switch)  
3. Run 16 ga. wire from small realy terminal  
on second solenoid to S6 on Circuit board  
and one post of the second PBS.  
4. Wire freshwater solenoid see below.  
Freshwater Solenoid valve wiring  
1. Run 16 ga. wire from battery positive to one  
of the wires on the solenoid with 3 amp fuse  
in line.  
2. Run 16 ga. wire from wire on solenoid not  
used to H1 on Purasan Circuit Board.  
PLUMBING  
Follow installation instructions on page 8 and  
connect second toilet to second intake port  
14  
Download from Www.Somanuals.com. All Manuals Search And Download.  
NOTE:  
Discharge of raw, untreated sewage is prohibited in all U.S. waters inside the three mile limit except in the Gulf of Mexico  
where the limit is nine miles. "Y" valves, if installed, must direct toilet discharge to a U.S.C.G. approved treatment  
system or holding tank and must be secured in that position while inside the three-mile limit.  
The EPAstandards state that in freshwater lakes, freshwater reservoirs or other freshwater impoundments whose inlets or outlets  
are such to prevent the ingress or egress by vessel traffic subject to this regulation, or in rivers not capable of navigation by  
interstate vessel traffic subject to this regulation, marine sanitation devices certified by the U.S. Coast Guard installed on all  
vessels shall be designed and operated to prevent the overboard discharge of sewage, treated or untreated, or any waste derived  
from sewage. The EPA standards further state that this shall not be construed to prohibit the carriage of Coast Guard-certified  
flow-through treatment devices which have been secured so as to prevent such discharges. They also state that waters where a  
Coast Guard-certified marine sanitation device permitting discharge is allowed including coastal water estuaries, the Great  
Lakes and interconnected waterways, freshwater lakes and impoundments accessible through locks, and other flowing waters  
that are navigable interstate by vessels subject to this regulation (40 CFR 140.3)  
15  
Download from Www.Somanuals.com. All Manuals Search And Download.  
2 1/4"  
(5.7cm)  
l  
ss  
Template for  
Switch Panel  
CUT OUT  
HATCHED  
AREA  
k (2)  
unting  
es  
3 3/4"  
9.5cm  
Of  
Panel  
LIMITED WARRANTY  
Raritan Engineering Company warrants to the original purchaser that this product is free of defects in materials or workmanship for a period of one year  
from the product’s date of purchase. Should this product prove defective by reason of improper workmanship and/or materials within the warranty period  
, Raritan shall, at its sole option, repair or replace the product.  
1. TO OBTAIN WARRANTY SERVICE, Consumer must deliver the product prepaid, together with a detailed description of the problem, to Raritan at 530  
Orange St., Millville, N.J. 08332, or 3101 SW 2nd Ave. Ft. Lauderdale, FL 33315. When requesting warranty service, purchaser must present a sales slip  
orotherdocumentwhichestablishesproofofpurchase.THERETURNOFTHEOWNERREGISTRATIONCARDISNOTACONDITIONPRECEDENT  
OF WARRANTY COVERAGE. However, please complete and return the owner Registration Card so that Raritan can contact you should a question of  
safety arise which could affect you.  
2. THIS WARRANTY DOES NOT COVER defects caused by modifications, alterations, repairs or service of this product by anyone other than Raritan;  
defects in materials or workmanship supplied by others in the process of installation of this product; defects caused by installation of this product other than  
in accordance with the manufacturer’s recommended installation instructions or standard industry procedures; physical abuse to, or misuse of, this product.  
This warranty also does not cover damages to equipment caused by fire, flood, external water, excessive corrosion or Act of God.  
3. ANY EXPRESS WARRANTY NOT PROVIDED HEREIN, AND ANY REMEDY FOR BREACH OF CONTRACT WHICH BUT FOR THIS  
PROVISION MIGHT ARISE BY IMPLICATION OR OPERATION OF LAW, IS HEREBY EXCLUDED AND DISCLAIMED. ALL IMPLIED  
WARRANTIES SUCH AS THOSE OF MERCHANTABILITY AND OF FITNESS FOR A PARTICULAR PURPOSE, IF APPLICABLE, AS WELL AS  
ANY IMPLIED WARRANTIES WHICH MIGHT ARISE BY IMPLICATION OF LAW, ARE EXPRESSLY LIMITED TO A TERM OF ONE YEAR.  
SOME STATES DO NOT ALLOW LIMITATIONS ON HOW LONG A LIMITED WARRANTY LASTS, SO THE ABOVE LIMITATION MAY NOT  
APPLY TO YOU.  
4. UNDER NO CIRCUMSTANCES SHALL RARITAN BE LIABLE TO PURCHASER OR ANY OTHER PERSONS FOR ANY SPECIAL OR  
CONSEQUENTIAL DAMAGES, WHETHER ARISING OUT OF BREACH OF WARRANTY, BREACH OF CONTRACT, OR OTHERWISE. SOME  
STATES DO NOT ALLOW THE EXCLUSION OR LIMITATION OF INCIDENTAL OR CONSEQUENTIAL DAMAGES, SO THE ABOVE  
LIMITATION OR EXCLUSION MAY NOT APPLY TO YOU.  
5. No other person or entity is authorized to make any express warranty, promise or affirmation of fact or to assume any other liability on behalf of Raritan  
in connection with its products except as specifically set forth in this warranty.  
6. This warranty gives you specific legal rights, and you may also have other rights which vary from state to state.  
530 Orange Street, Millville, NJ 08332 USA  
Telephone: 856-825-4900  
Southern Office and Plant:  
FAX: 856-825-4409  
3101 SW Second Avenue, Fort Lauderdale, FL 33315 USA  
Telephone: 954-525-0378 FAX: 954-764-4370  
L405 0911kgs  
Specifications Subject to Change Without Notice  
Printed in U.S.A.  
16  
Download from Www.Somanuals.com. All Manuals Search And Download.  

Q Logic Switch IB6054601 00 D User Guide
Radio Shack Motorized Toy Car 63 4324 User Guide
RCA Clock Radio RP3753 User Guide
Ricoh All in One Printer MP 1100 User Guide
Roland Musical Instrument MC 909 User Guide
Samsung Digital Camera 630 User Guide
Samsung Stereo System HT Z110 User Guide
Samsung TV Mount WMN4675MD User Guide
Sangean Electronics Portable Radio DT 220V User Guide
Scientific Atlanta Cable Box 3100HD User Guide