90 Ceramic
with Glide-out™ grill
Users Guide
Installation & Service Instructions
U109650-02
Download from Www.Somanuals.com. All Manuals Search And Download.
Contents
3
Download from Www.Somanuals.com. All Manuals Search And Download.
The Hob
When you cook on a ceramic hob its very
important to use the right sort of pans...
3
Always use pans that are the same size as (or
slightly larger than) the areas marked on the hob top.
Using smaller pans wastes heat, and any spillage will be
burnt on. Using a lid will help the contents boil more
quickly.
Use only pans that are suitable for ceramic hobs.
We recommend stainless steel and enamelled
steel pans because pots and pans with copper or
aluminium bases leave traces on the hob that are
difficult to remove.
4
Always lift pans off the hob. Sliding pans may cause
marks and scratches. Always turn the control to the off
position before removing a pan.
Glass-ceramic cookware is not suitable because of its
poor conductivity.
1
Pots and pans should have thick, smooth, flat
bottoms. This ensures that there is the maximum heat
transfer from the hob to the pan, making cooking quick
and energy efficient.
5
There are indicator lights for each of the cooking
areas. These come on when a hob control is turned on
and stay lit while the surface cools. Always take care
before touching the surface even when it is turned off
- it may be hotter than you think.
Never use a round bottomed Wok even with a stand.
2
The very best pans have bases that are very slightly
curved in when cold. If you hold a ruler across the
bottom you will see a small gap in the middle. When
they heat up the metal expands and lies flat on the
cooking surface.
6
The ratings of the cooking areas are shown on the
diagram below.
Make sure that the base of the pan is clean and dry to
prevent any residue burning onto the hob panel. This
also helps prevent scratches and deposits (such as lime
specks).
4
Download from Www.Somanuals.com. All Manuals Search And Download.
Naturally, the surface must be washed after use
in order to prevent it from becoming scratched or
dirty.
7
Although the ceramic surface is very strong, a
heavy or sharp falling object (a salt cellar for example)
might cause the surface to crack. If you find a crack in
the surface immediately disconnect the appliance from
the supply and arrange for its repair.
Only scratches in the hob surface reported
within 14 days of cooker installation are covered
by the guarantee. Scratches caused by usage are
not covered.
When cooking on the hob you may see the hob
area you are using switch off and on. This is caused
by a safety device that limits the temperature of
the hob. It is quite normal, especially when cooking
at high temperatures. If it happens a lot with a
particular pan however it may mean the pan is not
suitable – perhaps too small or too uneven - for a
ceramic hob.
Care should be taken that no water seeps into the
appliance.
Sugar spillage will permanently damage the
hob and therefore must be cleaned off with care
immediately. Never let sugar spillage cool before
trying to remove it.
8
The areas marked with two concentric circles have
an inner and an outer element.
If sugar or foods with high sugar content,
aluminium foil or plastic items are accidentally
allowed to melt on the hob surface remove them
immediately from the hot cooking area using
a scraper to avoid any possible damage to the
surface. See the ‘Cleaning your cooker’section of
these instructions.
Turn the control knob clockwise to heat the whole area
for larger pans - turn it the other way to just heat the
inner part for smaller pans.
Never cut directly on the cooking surface.
Don’t cook directly on the hob surface i.e. without
a pan or utensil
Don’t use the hob as a work surface
Don’t drag or slide utensils across the hob surface
Don’t place anything between the base of the pan
and the hob surface (i.e. asbestos mats, aluminium
foil, Wok stand)
10 Never cook directly on the surface.
Don’t leave utensils, foodstuffs or combustible
items on the hob when it is not in use. (e.g. tea
towels, frying pans containing oil)
Don’t place plastic or aluminium foil, or plastic
containers on the hob
Don’t leave the hob zones switched on unless
being used for cooking
The kind of pan you use and the quantity of food
affects the setting required. Higher settings are
required for larger quantities of food.
Don’t place large preserving pans or fish kettles
across two heating zones
Don’t place utensils partly covering a heating zone.
Always place utensils centrally.
5
Download from Www.Somanuals.com. All Manuals Search And Download.
The Glide-out™ Grill
3
For best results preheat for 2 minutes with the grill
Caution: Accessible parts may be hot
when the grill is in use. Young children
should be kept away.
pan in position. After placing your food on the grill pan
grid, slide in the grill carriage. Adjust the heat to suit by
turning the knob.
Make sure the grill carriage is pushed right in.
Before using the grill for the first time, make
sure that all packing materials have been
removed and then to dispel manufacturing
odours, turn on the grill and run for 30 minutes
with the grill pan in position, pushed fully back,
and the grill door open.
Never close the grill door when the grill is on.
4
The grill pan grid can be turned over to give two
grilling positions.
Make sure the room is well ventilated to the
outside air, by opening windows or turning on a
cooker hood for example. We recommend that
people with respiratory or allergy problems
should vacate the area for this brief period.
Using the grill
Don’t leave the grill on for more than a few
moments, without the grill pan underneath it.
1
Open the grill door and pull the grill pan carriage
forward using the handle.
For best results, especially with toast, preheat the
grill with the grill pan in the cooking position for
two minutes before use.
Before you remove any of the grill parts for
cleaning make sure that they are cool or use
oven gloves.
The grill trivet can be removed and the food placed
on it while you are waiting for the grill to preheat.
The grill pan and grill pan carriage can be easily
removed for cleaning. See the ‘Cleaning your
cooker’ section of these instructions.
The grill pan gets very hot when the grill is on.
Don't touch the pan or trivet unless you are sure
it is cool.
When you pull the grill pan forward is the wide rim
at the front? It's important that the wider part is at
the front.
2
After placing your food on the grill grid, slide the
grill carriage into the grill chamber. Make sure it is
pushed right in.
The grill has two elements that allow either the whole
area of the pan to be heated or just the right hand half.
To heat the whole grill, turn the knob clockwise.
To heat the right hand half turn it anticlockwise.
The neon indicator light by the grill control will come
on.
6
Download from Www.Somanuals.com. All Manuals Search And Download.
The Ovens
During use the appliance becomes hot. Care should be taken to avoid the touching heating elements
inside the oven.
Before using for the first time, to dispel manufacturing odours turn the ovens to 230°C and run for an
hour. To clear the smell, make sure the room is well ventilated to the outside air, by opening windows or
turning on a cooker hood for example. We recommend that people with respiratory or allergy problems
should vacate the area for this brief period.
The clock must be set to the time of day before the ovens will work. See ‘The Clock’section for instructions on
setting the time of day.
The Left Hand Oven
The Right Hand Tall Oven
The left hand oven is a Multi-function oven. As well as
The fan in the right hand oven circulates hot air
the oven fan and fan element, it is fitted with two extra continuously, which means faster more even cooking.
heating elements, one visible in the top of the oven
The recommended cooking temperatures for a fanned
and the second under the oven base. Take care to avoid
oven are generally lower than a non-fanned oven.
touching the top element and element deflector when
placing or removing items from the oven. For more
detail on this oven see the section ‘Multi-function oven’.
The Multi-function
The right hand
oven has two
fan oven control is
controls, a function
at the right hand
selector and a
end of the control
temperature setting
panel.
knob.
Turn the function selector
Turn the oven temperature
control to a cooking
knob to the temperature
function. This is the fan oven
you need.
setting.
Turn the oven temperature
knob to the temperature
The oven indicator light
you need.
will glow until the oven has
The oven heating light will
reached the temperature
glow until the oven has
you selected. It will then
reached the temperature
cycle on and off during
you selected. It will then
cooking
cycle on and off during
cooking.
7
Download from Www.Somanuals.com. All Manuals Search And Download.
The Clock
You can use the timer to turn the ovens on and off.
The clock must be set to the time of day before the
ovens will work.
To time something that’s cooking
(minute minder)
Turn the Timer knob
to the right to the (
Setting the time of day
)
minute minder setting
- it should click into
position.
Use the Adjusting knob
to set the time you need.
Timer knob
Adjusting knob
You can turn the knob back to the ( ) manual
setting to keep an eye on the time of day or leave it
in the ( ) minute minder position as the time ticks
down.
When the clock is first connected the display will
flash ( ) and ( ) alternately.
To stop the beeper when it sounds
To set the clock to read
the time of day turn
and hold the Timer
knob to the clock
symbol ( ).
Turn the Adjusting knob anticlockwise
To stop automatically
Use when you have started the oven manually.
Turn the Timer knob to
the ( ) position.
At the same time turn
the Adjusting knob left
or right until the clock
shows the time of day.
Use the Adjusting knob to
set the time you need.
Let go of the Timer knob and it will spring back to
the vertical ( ) oven manual setting.
‘Stop Time’shows.
AUTO will show in the
display.
If the key symbol ( ) appears on the left of the
display you have accidentally turned on the key
lock feature. See the section ‘Clock Special Features’.
AUTO
Turn the Timer knob to the (
) setting.
When your cooking is finished the beeper sounds.
Turn the Timer knob to the vertical ( ) to return to
manual cooking.
8
Download from Www.Somanuals.com. All Manuals Search And Download.
To start & stop the oven automatically
Before you set the clock, you must have two
numbers clearly in mind.
AUTO is showing, you want to reset to
manual cooking.
You can cancel any automatic settings by turning
the Timer knob to the vertical manual symbol ( ).
The ‘cook time’, which is the period of time you
want the oven to cook.
Clock Special Features - Key Lock
When the key lock is activated, the clock can be
operated as usual but the ovens are locked and
will not come on. This means that your child could
select a cook program but the program will not be
activated and ovens will not switch on.
The ‘stop time’, which is the time of day you want
the oven to stop cooking.
You cannot set a start time directly - this is set
automatically by setting the cooking period and
stop time.
To activate the key lock
Make sure that the clock is in manual mode and
cancel any active programs.
Turn the Timer knob to
the ( ) position.
Turn and hold the Timer
knob to the clock symbol
(
) for about 8 seconds.
‘On’will appear on the
display.
Use the Adjusting knob to
set the ‘cooking time’you
need.
Keep holding the Timer
knob turned to the clock
symbol ( ) and turn the
Adjusting knob clockwise
until the key symbol
( ) and ‘Of’shows on the
display. Let go of the
knobs
Turn the Timer knob to
the ( ) position.
The display will show the
current time of day plus
the ‘cook period’you just
set.
The ovens are now
locked. After a few
seconds the display will
revert to show the time of
day and the key symbol.
Use the Adjusting knob
to set the ‘Stop time’you
need.
To turn off the key lock
‘Stop Time’shows. AUTO
will show in the display.
Turn and hold the Timer
knob to the clock symbol
Set the oven(s) to the cooking temperature you
need (don’t forget to set a function if using the
Multi-function oven).
(
) for about 8 seconds.
‘Of’will appear on the
display.
Turn the Timer knob to the (AUTO) setting.
When your cooking is finished the beeper sounds.
Turn the Timer knob to the vertical ( ) to return to
manual cooking.
Keep holding the Timer
knob turned to the clock
symbol ( ) and turn the
Adjusting knob clockwise
until the key symbol
( ) goes out on the display
and ‘On’shows. Let go of
the knobs.
If you are out, don’t worry about the beeper going
off, it stops after a while. When you return, turn the
Timer knob to the vertical ( ) position to return
to manual cooking. Turn the thermostat to the off
position.
9
Download from Www.Somanuals.com. All Manuals Search And Download.
Both Ovens
After a few seconds the
display will revert to show
the time of day.
The wire shelves should always be pushed firmly to
the back of the oven.
The ovens can now be
used normally.
Baking trays, meat tins et cetera should be placed level
and centrally on the oven’s wire shelves. Keep all trays
and containers away from the sides of the oven, as
overbrowning of the food may occur.
Cooking using the timer
The timer can be used to turn just one oven or
both on and off automatically. The start and stop
time must be the same for both ovens but different
cooking temperatures can be set.
For even browning maximum recommended size
for a baking tray is:-
3
3
8
8
Main oven 340mm (13 / ”) by 340mm (13 / ”).
1
2
If you want to turn one of the ovens on at the
same time as the timer is set for automatic
cooking, you must wait until the timer has turned
on the oven/ ovens first. Then you can adjust
either of them manually in the normal way.
Tall oven
230mm (9”) by 320mm (12 / ”).
Cooking high moisture content
foods can create a ‘steam burst’,
when the oven door is opened.
When opening the oven stand
well back and allow any steam
to disperse.
You can set the oven to turn on any time over the
following 24 hour period.
If you want to cook more than one dish, choose
dishes that require approximately the same time.
However, dishes can be ‘slowed down’ slightly
by using small containers and covering them
with aluminium foil, or ‘speeded up’ slightly by
cooking smaller quantities or placing in larger
containers.
When the oven is on, don’t leave
the door open for longer than
necessary, otherwise the knobs
may get very hot.
•
Always leave a ‘fingers width’
between dishes on the same shelf. This allows the
heat to circulate freely around them.
The Cook & Clean oven liners (see Cleaning your
cooker) work better when fat splashes are avoided.
Cover meat when cooking.
Very perishable foods such as pork or fish should be
avoided if a long delay period is planned, especially
in hot weather.
•
Don’t place warm food in the oven.
Don’t use an oven already warm.
Don’t use if an adjoining oven is warm.
Avoid using wine or beer if there is a delay period,
as fermentation may take place.
• To reduce fat splashing when you add vegetables
to hot fat around a roast, dry them thoroughly or
brush lightly with cooking oil.
• Sufficient heat rises out of the oven while
cooking to warm plates in the grill compartment.
• If you want to brown the base of a pastry dish,
preheat a baking tray for 15 minutes before
placing the dish in the centre of the tray.
To avoid curdling, cream should be added to
dishes just before serving.
Fresh vegetables, which may discolour during a
delay period, should be coated in melted fat or
immersed in a water and lemon juice solution.
Fruit pies, custard tarts or similar wet mixtures on
top of uncooked pastry are only satisfactory if there
is a short delay period. Dishes containing leftover
cooked meat or poultry should not be cooked
automatically if there is a delay period.
•
Where dishes may boil and spill over during
cooking, place them on a baking tray.
Whole poultry must be thoroughly defrosted
before placing in the oven.
Check that meat and poultry are fully cooked
before serving.
10
Download from Www.Somanuals.com. All Manuals Search And Download.
Multi-function oven
Fan oven
The Multi-function oven is on the left hand side.
It has many varied uses. We suggest you keep a
careful eye on your cooking until you are familiar
with each function. Remember - not all functions
will be suitable for all food types.
This function operates the fan and the
heating element around it. An even heat is
produced throughout the oven, allowing you to
cook large amounts quickly.
Fan oven cooking is particularly suitable for baking
on several shelves at one time and is a good ‘all-
round’function. It may be necessary to reduce the
temperature by approximately 10°C for recipes
previously cooked in a conventional oven.
If you wish to pre-heat the oven, wait until the
indicator light has gone out before inserting the
food.
Fanned grilling
This function operates the fan whilst the top
element is on. It produces a more even, less fierce
heat than a conventional grill. For best results, place
the food to be grilled, on a grid over a roasting tin,
which should be smaller than a conventional grill
pan. This allows greater air circulation. Thick pieces
of meat or fish are ideal for grilling in this way, as
the circulated air reduces the fierceness of the heat
from the grill. The oven door should be kept closed
whilst grilling is in progress, so saving energy. You
will also find that the food needs to be watched
and turned less than for normal grilling. Pre-heat
this function before cooking.
Please remember that all cookers vary -
temperatures in your new Elan ovens may differ to
those in your previous cooker.
Multi-function oven functions
Defrost
This function operates the fan to circulate
cold air only. No heat is applied. This enables small
items such as desserts, cream cakes and pieces of
meat, fish and poultry to be defrosted.
Defrosting in this way speeds up the process and
protects the food from flies. Pieces of meat, fish and
poultry should be placed on a rack, over a tray to
catch any drips. Be sure to wash the rack and tray
after defrosting.
Fan assisted oven
This function operates the fan, circulating
air heated by the elements at the top and the
base of the oven. The combination of fan and
conventional cooking (top and base heat) makes
this function ideal for cooking large items that need
thorough cooking, such as a large meat roast. It is
also possible to bake on two shelves at one time,
although they will need to be swapped over during
the cooking time, as the heat at the top of the
oven is greater than at the base, when using this
function.
Defrost with the oven door closed.
Large items, such as whole chickens and
joints should not be defrosted in this way. We
recommend this be carried out in a refrigerator.
Defrosting should not be carried out in a warm
oven or when an adjoining oven is in use or still
warm.
This is a fast intensive form of cooking; keep an
eye on the food cooking until you have become
accustomed to this function.
Ensure that dairy foods, meat and poultry are
completely defrosted before cooking.
11
Download from Www.Somanuals.com. All Manuals Search And Download.
Handyrack
Conventional oven (top and
base heat)
This function combines the heat from the top and
base elements. It is particularly suitable for roasting
and baking pastry, cakes and biscuits. Food cooked
on the top shelf will brown and crisp faster than on
the lower shelf, because the heat is greater at the
top of the oven than at the base, as in ‘Fan assisted
oven’function. Similar items being cooked will
need to be swapped around for even cooking. This
means that foods requiring different temperatures
can be cooked together, using the cooler zone in
the lower half of the oven and hotter area to the
top.
The maximum weight than can be held by the
Handyrack is 5.5kg (12lb). It should only be used with
the supplied meat tin, which is designed to fit the
Handyrack. Any other vessel could be unstable.
The Handyrack fits on the Main oven door. Food
cooking on it is easy to attend to, because it’s
accessible when the door is open. It can be fitted at
two different heights. One of the oven shelves must
be removed and the other positioned to suit.
Browning element
This function uses the element in the top
of the oven only. It is a useful function for the
browning or finishing of pasta dishes, vegetables
in sauce, shepherds pie and lasagne, the item to be
browned being already hot before switching to the
top element.
When the Handyrack is used in its highest position,
other dishes can be cooked on the bottom shelf
position of the oven.
When the Handyrack is used in its lowest position,
other dishes can be cooked on the second shelf
position of the oven.
Base heat
This function uses the base element only. It
will crisp up your pizza or quiche base or finish off
cooking the base of a pastry case on a lower shelf.
It is also a gentle heat, good for slow cooking of
casseroles in the middle of the oven or for plate
warming.
To fit the Handyrack,
locate one side of it on
the door bracket.
The Browning and Base heat functions are useful
additions to your oven, giving you flexibility to
finish off items to perfection. With use, you will
soon realise how these functions can combine to
extend your cooking skills.
Then spring the other
side out to clip it onto
the other bracket.
12
Download from Www.Somanuals.com. All Manuals Search And Download.
Main Oven shelves
Tall Oven shelves
The tall oven is
supplied with four
normal cooking shelves
and a plate warming
shelf.
the shelf guard should be at the back pointing upwards
As well as a flat shelf some models are supplied
with a drop shelf. The drop shelf increases the
possibilities for oven shelf spacing.
When using the tall oven you can cook on all four
shelves at the same time; but make sure they are
well spaced out to allow the hot air to circulate.
Steam
The oven shelves can be easily removed and
refitted.
During cooking, food naturally produces steam,
particularly when cooking foods with high water
content (e.g. oven chips). There may be some steam
visible at the grille at the rear of the hotplate. This is
perfectly normal.
Pull the shelf forward until
the back of the shelf is
stopped by the shelf stop
bumps in the oven sides.
As this steam can condense to water droplets on the
cool outer trim of the oven, it may be necessary during
cooking to wipe away any moisture with a soft cloth.
This will also help to prevent soiling and discolouration
of the oven exterior by cooking vapours.
Lift up the front of the shelf
so the back of the shelf will
pass under the shelf stop
and then pull the shelf
forward.
Oven light
Press the appropriate button to turn on one of the
oven lights.
To refit the shelf, line up the shelf with a groove
in the oven side and push the shelf back until the
ends hit the shelf stop. Lift up the front so the shelf
ends clear the shelf stops, and then lower the front
so that the shelf is level and push it fully back.
If one of the oven lights fail, turn off the power
supply before you change the bulb. See the
‘Troubleshooting’section for details on how to
change an oven light bulb.
13
Download from Www.Somanuals.com. All Manuals Search And Download.
Multi-function Oven cooking guide
Remember - not all functions will be suitable for all food types. The oven control settings and cooking
times given are intended to be used only as a guide. Individual tastes may require the temperature to be
altered to provide a preferred result.
Food is cooked at lower temperature in a fan oven than in a conventional oven. When using recipes,
reduce the temperature by 10°C and the cooking time by 5-10 minutes. The temperature in the fanned
oven does not vary with height in the oven - so you can use any shelf.
The shelves should not be fitted directly one above the other. When cooking on more than one shelf
always leave at least one runner space between them. Place baking trays, individual cake tins or baking
dishes centrally on the oven shelf. For best results pre-heat the oven until the oven indicator light goes out.
Cooking chart - Fan assisted oven function
Oven Shelf
Food
Fairy cake
Scone
Temp
170°C
180°C
160°C
190°C
Position
2-4
2-4
2-4
2-4
3
Approximate Cooking Time
20 min
15 min
Deep apple pie
Plate tart
45 min interchange after 25 minutes
45 min interchange After 25 minutes
1 hr 45 min - 2 hr
Rich fruit cake 197mm x 92mm 145°C
Victoria sandwich 180mm
Milk pudding
170°C
150°C
220°C
2-4
3
20 - 25 min
2 hrs
Puff pastry
3 - 5
15-40 mins according to size. Interchange
2/3rds through cooking time
For roast meats and poultry refer to the Fan oven guide - reduce cooking time slightly.
500g is approximately 1lb (1lb 2oz)
Ensure meat and poultry is fully cooked before serving
14
Download from Www.Somanuals.com. All Manuals Search And Download.
Oven Cooking chart - Conventional and full Fan oven functions
Convection Oven
Shelf
Fan Oven
Food
Temperature
Position
Temperature Approximate Cooking Time
FISH
190°C
190°C
190°C
3
3
3
180°C
180°C
180°C
Fillets 15-20mins.
Whole 10mins.per 500g + 10mins.
Steaks according to thickness.
ROAST MEATS
Beef with bone
160°C
200°C
160°C
200°C
160°C
200°C
160°C
200°C
2-3
2-3
2-3
2-3
2-3
2-3
2-3
2-3
150°C
190°C
150°C
190°C
170°C
190°C
150°C
190°C
20-25mins. per 500g + 20-25mins.
15-20mins. per 500g + 15-20mins.
30-35mins. per 500g + 30-35mins.
20-25mins. per 500g + 20-25mins.
30-35mins. per 500g + 30-35mins.
25-35mins. per 500g + 25-30mins.
35-40mins. per 500g + 35-40mins.
25-30mins. per 500g + 25-30mins.
Beef without bone
Lamb
Pork
Stuffed and rolled - Add approx. 10 mins. per 500g to above cooking times or cook at 200°C for 20mins. then 160°C for
remainder.
THOROUGHLY THAW FROZEN JOINTS AND POULTRY BEFORE COOKING.
POULTRY
Chicken
160°C
200°C
160°C
200°C
2-3
2-3
2
150°C
190°C
150°C
190°C
20-25mins. per 500g + 20-25mins.
15-20mins. per 500g + 15-20mins.
20-25mins. per 500g + 20-25mins.
15-20mins. per 500g + 15-20mins.
Turkey
2
Stuffed Poultry - Cook at 200°C or at 200°C for 20mins. then 160°C for remainder. Prepacked (fresh or frozen) follow packers
cooking times
CASSEROLE
YORKSHIRE PUDDING
CAKES
140-150°C
220°C
2-3
4
140°C
200°C
2-4hrs according to recipe
Large tin 30-35mins. Individual 10-20mins.
Very Rich Fruit
Rich fruit (180mm)
Madeira (180mm)
Queen Cakes
Scones
140°C
150°C
160°C
180°C
200°C
180°C
2
140°C
145°C
150°C
170°C
190°C
170°C
45-50mins. per 500g mixture
21/2-3hrs.
2
2
80-90mins.
2 & 4 or 3
2 & 4 or 3
2 & 4 or 3
15-25mins.
10-15mins.
Victoria Sandwich
20-30mins.
PASTRIES
Plate Tart
200°C
200°C
200°C
220°C
220°C
110°C
2 & 4
2 & 4
4
190°C
190°C
190°C
200°C
200°C
100°C
45-50mins. Interchange after 25mins.
35-40mins.
Fruit Pie
Tartlets
15-20mins. according to size.
20-40mins. according to size.
20-30mins.
Puff Pastry
2, 3 or 4
2 & 4
3
BREAD
MERINGUES
PUDDINGS
Baked Egg Custard
Baked sponge pudding
Milk pudding
2-21/2hrs
160°C
190°C
3
3
3
150°C
180°C
150°C
45mins.-1hr.
40-45mins.
2-3hrs.
140-150°C
15
Download from Www.Somanuals.com. All Manuals Search And Download.
Cleaning for spills
Cleaning your cooker
For spills and boil-overs that occur while cooking,
turn the unit off and wipe the area surrounding
the hot zone with a clean paper towel. If a spill
(other than a sugary substance) is on the hot zone,
do not clean until the unit is completely cooled
down and follow the instructions below (“Cleaning
for burned-on spills”). If you accidentally melt
anything on the cooking or if you spill foods with a
high sugar content (preserves, tomato sauce, etc.),
REMOVE the spill IMMEDIATELY with a razor scraper,
while the unit is still hot. IMPORTANT: Use an oven
glove to protect your hand from potential burns.
Scrape the major spill or melted material from the
cooking zone and push into a cold area. Then, turn
the unit “OFF”and allow to cool before cleaning
further. After the cooking surface cools down and
the heat indicator lights go off, use the daily care
procedure as outlined above.
Essential information
Before thorough cleaning isolate the electricity
supply. Remember to switch on the electricity
supply before use.
Never use paint solvents, washing soda,
caustic cleaners, biological powders, bleach,
chlorine based bleach cleaners, coarse
abrasives or salt. Don’t mix different cleaning
products - they may react together with
hazardous results.
Recommended cleaning materials are shown
in the table at the end of this section.
If you want to move your cooker for cleaning, see
the section called ‘Moving your cooker’.
All parts of the cooker can be cleaned with hot
soapy water - but take care that no surplus water
seeps into the appliance.
Cleaning for burned-on spills
Be sure that the heat indicator lights are off and the
hob is cool. Remove excess burned-on substance
with a single-edged razor scraper. Hold the scraper
at approximately a 30° angle to the surface and
scrape off the burned-on matter as you would
scrape paint off of a window.
For cleaning materials see the ‘Cleaning Table’at the
end of this section.
Hob
It’s very easy to clean the Hob with a recommended
cleaner.
CAUTION — Do not use abrasive cleaners or pads,
oven aerosols or pads or stain removers on the
surface.
Daily care
First of all, be sure that all heat indicator lights are
off and the cooking surface is cool. Apply a small
dab, about the size of a 10p piece, of ceramic
cooking cleaning cream in the centre of each area
to be cleaned. Dampen a clean paper towel and
work the cleaning cream on the cooking surface as
if you were cleaning a window. As a final step, wipe
the cooking surface with a clean, dry paper towel.
IMPORTANT: Take care when using a sharp scraper.
When you have removed as much as possible with
the scraper clean using the daily care procedure as
described above.
To remove metal rub-off
Sliding pans on the hob - especially aluminium or
copper pans can leave marks on the surface. These
marks often appear like scratches, but can be easily
removed using the procedure described above for
cleaning spills. If the rub-off marks are especially
stubborn, use the cleaning cream together with the
razor scraper, using the technique described above.
16
Download from Www.Somanuals.com. All Manuals Search And Download.
Glide-out™ Grill
Before you remove any of the grill parts for
cleaning make sure that they are cool.
The grill pan and grid should be washed in hot
soapy water. After grilling meats or any foods that
soil, leave to soak for a few minutes in the sink
immediately after use. Stubborn particles may be
removed from the grid by using a nylon brush.
Alternatively the grill pan can be washed in a dish
washer.
To remove the grill pan support frame, pull the grill
pan forward.
The side rails can be
removed to make
cleaning the grill
chamber easer by
unhooking them from
the grill chamber sides.
Slides can be wiped clean with soft cloth and mild
detergent.
Lift the grill pan clear of the support frame.
The support frame is held to the side rails by two
clips on each side.
Do not use any abrasive substance.
DO NOT put the side runners in a dishwasher
When you have finished, hook the side rails back
onto the sides of the chamber. To refit the frame
pull the side rails forward and for each side in turn
support the side rail and press the frame down into
the side rails. Replace the grill pan.
Control Panel and Doors
Avoid using any abrasive cleaners including
cream cleaners, e.g. Cif, on brushed Stainless Steel
surfaces. For best results use a liquid detergent e.g.
Domestos Multi Surface Cleaner.
For each side, support the side rail with one hand
and with the other hand lift the frame up and out of
the side clips.
The control panel and control knobs should only
be cleaned with a soft cloth wrung out in clean hot
soapy water. Wipe with a clean dampened cloth
then polish with a dry cloth. The oven doors should
only be cleaned with a soft cloth wrung out in clean
hot soapy water.
For safety, push the side rails back into the grill
chamber.
17
Download from Www.Somanuals.com. All Manuals Search And Download.
The Main Oven
Moving your cooker
The Main oven has panels which have been coated
with a special enamel that partly cleans itself. This
does not stop all marks on the lining, but helps to
reduce the amount of manual cleaning needed.
Switch off the electricity supply.
The cooker is heavy, two people may be required
to move it. There are two levelling rollers at the
back and also two screw down levelling feet at
the front.
The Cook & Clean panels work better above
200°C. If you do most of your cooking below this
temperature, occasionally remove the panels and
wipe with a lint free cloth and hot soapy water.
The panels should then be dried and replaced
and the oven heated at 200°C for about one
hour. This will ensure the Cook & Clean panels are
working effectively.
Don’t use steel wool (Brillo) or any other materials
that will scratch the surface. Don’t use oven
cleaning pads.
Removing the Oven Linings
Some of the lining panels can be removed for
cleaning and for cleaning behind. Remove the
shelves first.
Open the grill door and right hand oven door so
that you can get a good grip on the bottom of the
fascia panel as you move the oven.
The side panels of either oven can be removed.
Each side of the oven
is fixed with four fixing
screws. You don’t have
to remove the screws
to remove the oven
linings. Lift each side
panel upwards and
they will slide off the
screws. Then pull them
forwards.
Once the linings are removed, the oven enamel
interior can be cleaned.
Lift the front of the cooker slightly and pull forward.
Do not move the oven by pulling the door
handles or knobs.
The Tall Oven
To clean the oven sides
slide out the shelves,
unhook the supports
from the oven sides
and lift out.
Move the oven a bit at a time, checking behind it to
make sure the electricity supply cable is not caught.
Make sure the cable has sufficient slack to move the
cooker forward as you go along.
If a stability chain is fitted, release it as you ease
the cooker out. Don’t forget to refit it when you
replace the cooker.
When you replace the cooker, again check behind
to make sure that the electricity cable is not caught
or trapped.
18
Download from Www.Somanuals.com. All Manuals Search And Download.
Cleaning Table
Hobplate
Part
Finish
Recommended Cleaning Method
Ceramic Hob Glass with anodised
Remove any dried baked on food deposits with a ceramic hob scraper
aluminium surround. from the glass, available from electrical retailers i.e. Curry’s.
Clean with HobBrite Homecare Products or Easy-Do Hobcare Ceramic
and Halogen Hob Cleaner and Conditioner Easy-Do Products Ltd
(Curry’s) and polish with a soft cloth.
Do not use cleaners intended for the ceramic hob on the hob
surround. Only use hot soapy water and a soft cloth on the surround.
Outside of cooker
Part
Finish
Recommended Cleaning Method
Door & Door surround.
Enamel or paint
Hot soapy water, soft cloth.
Any stubborn stains, remove gently with a liquid
detergent.
Stainless Steel
Painted surface
E Cloth (Comet) or Vileda Microfibre Plus All Purpose Cloth
Freudenberg Household Products LP (supermarket)
Sides and Plinth
Hot soapy water, soft cloth.
Splashback/Rear Grille
Enamel or
Stainless Steel
Hot soapy water, soft cloth. Cream cleaner, with care, if
necessary.
Control panel
Paint, Enamel or
Stainless Steel
Warm soapy water. Do not use abrasive cleaners on
lettering.
Control Knobs/Handles
Plastic/ Chrome
Warm soapy water, soft cloth.
Oven Door Glass/Glass Lid
Toughened glass Hot soapy water, cream cleaner/scourer if necessary.
Oven and Grill
Part
Finish
Recommended Cleaning Method
Sides, floor & roof of oven -
Enamel
Any proprietary oven cleaner that is suitable for enamel.
NOT COOK & CLEAN OVEN
PANELS (see below)
CAUTION: CORROSIVE/CAUSTIC OVEN CLEANERS -
FOLLOW MANUFACTURERS INSTRUCTIONS. Do not allow
contact with the oven elements.
Cook & Clean Oven Panels
(some models only)
Special enamel
This surface cleans itself at 200°C and above, or the panels
that partly cleans can be removed and washed with hot soapy water and a
itself
nylon brush. (see ‘The Ovens’in ‘Cleaning your cooker’)
Oven Shelves, Handyrack, Grill Chrome
Trivet.
An oven interior cleaner that is suitable for chrome. Soap
filled pad. Dishwasher.
Grill Pan/Meat Tin (some
models only)
Enamel
Hot soapy water. Soap filled pad (Brillo). Dishwasher.
Cleaners listed are available from Supermarkets or
electrical retailers as stated. Cleaner manufacturer in
Italics
Regular cleaning is recommended. For easier
cleaning, wipe up any spillages immediately.
To help keep your oven clean, cover meat
when roasting, with foil or use a roasting
bag. Brush vegetables with fat before placing
around the meat.
For enameled surfaces use a cleaner that is approved
for use on vitreous enamel. The vitreous enamel
association has a list of approved cleaners. Contact
01527 893031.
19
Download from Www.Somanuals.com. All Manuals Search And Download.
The knobs get hot when I use the oven or the
grill, can I avoid this?
Troubleshooting
Yes, this is caused by heat rising from the oven or
the grill, and heating them up.
A crack has appeared in the Hob surface
Disconnect the cooker immediately from the power
supply and arrange for its repair. Don’t use the
cooker until after the repair. See the Customer care
leaflet for how to contact a service person.
Don’t leave the oven door open.
When grilling make sure that the grill door is
open with the grill pan pushed right back to the
‘backstop’.
My Hob is scratched
Have you used the correct cleaning methods?
If there is an installation problem and I don’t get
my original installer to come back to fix it who
pays?
Pots and pans with rough bottoms, or coarse
particles (salt or sand) between the pan and the
surface of the hob may cause scratches.
You do. Service organisations will charge for their
call outs if they are correcting work carried out by
your original installer. It’s in your interest to track
down your original installer.
Use the recommended cleaning methods. Make
sure pan bottoms are smooth and clean. Tiny
scratches are not removable but will become less
visible in time as a result of cleaning.
Current Operated Earth Leakage Breakers
Where the cooker installation is protected by a
30 milliamp sensitivity residual current device
(RCD), the combined use of your cooker and other
domestic appliances may occasionally cause
nuisance tripping. In these instances the cooker
circuit may need to be protected by fitting 100mA
device. This work should be carried out by a
qualified electrician.
Only scratches in the hob surface reported within
14 days of cooker installation are covered by the
guarantee. Scratches caused by usage are not
covered.
Metal markings on the Hob
Do not slide aluminium or copper pans across the
surface. Marks from aluminium and copper pans as
well as mineral deposits from water or food can be
removed with the cleaning cream.
Food is cooking too slowly, too quickly, or
burning
Steam is coming from the oven
Cooking times may differ from your previous
oven. Check that you are using the recommended
temperatures and shelf positions. See the ‘Oven
cooking guide’section of these instructions.
The oven control settings and cooking times are
intended to be used only as a guide. Individual
tastes may require the temperature to be altered
either way, to get the results you want. Try cooking
at different temperature setting.
During cooking, food naturally produces steam,
particularly when cooking foods with high water
content (e.g. oven chips). There may be some steam
visible at the grille at the rear of the hotplate. This
is perfectly normal. Steam can condense to water
droplets on the cool outer trim or the oven door.
It may be necessary during cooking to wipe away
any moisture with a soft cloth. This will also help
to prevent soiling and discolouration of the oven
exterior by cooking vapours.
The oven is not cooking evenly
Do not use a tin or baking tray larger than 340mm
x 340mm in the Main oven or 232mm x 321mm in
the Tall oven.
If you are cooking a large item, be prepared to turn
it round during cooking.
Take care when opening the oven door, as there
may be a momentary puff of steam when the oven
door is opened. Stand well back and allow any
steam to disperse.
If two shelves are used, check that space has been
left for the heat to circulate. When a baking tray is
put into the oven, make sure it is placed centrally
on the shelf.
Check that the door seal is not damaged and that
the door catch is adjusted so that the door is held
firmly against the seal.
A dish of water when placed on the shelf should be
the same depth all over. (For example, if it is deeper
at the back, then the back of the cooker should be
raised up or the front lowered). If the cooker is not
level arrange for your supplier to level it for you.
The oven fan is noisy
The note of the oven fan may change as the oven
heats up - this is perfectly normal.
What cleaning materials are recommended for
the cooker?
See the ‘Cleaning your cooker' section of these
instructons for a full list of recommended cleaning
materials. We do not recommend Mr. Muscle, as it
contains chemicals which may damage the surfaces
of your cooker.
20
Download from Www.Somanuals.com. All Manuals Search And Download.
Unscrew the bulb cover by turning anticlockwise. It
may be very stiff.
Oven not coming on when turned on manually
Is the power on? Is the clock illuminated?
Is the key symbol ( ) showing in the display? See
the Clock section of the instructions for more
information on the key lock feature of the clock.
If using the Multi-function oven have you set a
cooking function?
If not there may be something wrong with the
power supply. Is the cooker supply on at the
isolator switch?
Taking care to protect your fingers in case the bulb
should shatter, unscrew the old bulb.
Oven not coming on when automatic cooking
Timer set correctly but oven knob left OFF by
mistake?
Screw in the new bulb, screw back the bulb cover.
Turn on the electricity supply and check that the
bulb now lights.
Is the key symbol ( ) showing in the display? See
the Clock section of the instructions for more
information on the key lock feature of the clock.
If using the Multi-function oven have you set a
cooking function?
Oven temperature getting hotter as the cooker
gets older
If turning the knob down has not worked or only
worked for a short time then you may need a
new thermostat. This should be fitted by a service
person.
Grill not cooking properly
Are you using the pan and trivet supplied with
the cooker? Is the pan being used on the runners,
not the floor of the compartment? Is the grill pan
pushed fully back to stop?
When you pull the
grill pan forward is the
wide rim at the front?
It's important that the
wider part is at the front.
The oven light is not working
The bulb has probably blown. You can buy a
replacement bulb (which is not covered under the
guarantee) from a good electrical shop. Ask for an
Edison screw fitting 15w 240v lamp, FOR OVENS. It
must be a special bulb, heat resistant to 300 °C. See
the 'Customer Care' leaflet for spares by mail order.
Turn off the power supply.
Make sure the oven is cool. Open the oven door
and remove the oven shelves.
21
Download from Www.Somanuals.com. All Manuals Search And Download.
In the interests of hygiene and safety the cooker
should be kept clean at all times as a build up in fats
and other food stuff could result in a fire.
General Safety Instructions
The cooker must be installed by a qualified
electrician in accordance with the installation
instructions. It should be serviced by a qualified
service engineer and only approved spare parts
used. Have the installer show you the location of
the cooker control switch. Mark it for easy reference.
Always allow the cooker to cool and then switch off
at the mains and before cleaning or carrying out
any maintenance work, unless specified otherwise
in this guide.
We recommend that you avoid wiping any
surface unit areas until they have cooled and
the indicator light has gone off. Sugar spills
are the exception to this. Please see ‘Cleaning
your cooker’. When the hob is cool, use only the
recommended cleaning cream to clean the hob.
To avoid possible damage to the cooking
surface, do not apply the cleaning cream to the
glass surface when it is hot. Read and follow all
instructions and warnings on the cleaning cream
labels. After cleaning, use a dry cloth or paper towel
to remove any cleaning cream residue.
All parts of the cooker become hot with use and
will retain heat even after you have stopped
cooking.
Take care when touching the hob especially the
marked cooking areas. The glass surface of the hob
will retain heat after the controls have been turned
off. To minimize the possibility of burns, always be
certain that the hob controls are in the OFF position
and that the entire glass surface is cool before
attempting to clean the hob.
Avoid heating an empty pan. Doing so may
damage the hob and the pan.
Always keep combustible wall coverings or curtains
etc. a safe distance away from your cooker.
Do not place or store items on top of the glass
hob surface when it is not in use.
Use dry oven gloves when applicable - using
damp gloves might result in steam burns when
you touch a hot surface. Never operate the
cooker with wet hands.
Do not spray aerosols in the vicinity of the cooker
while it is in on.
Do not store or use combustible materials,
or flammable liquids in the vicinity of this
appliance.
Do not use a towel or other bulky cloth in place of
a glove. They might catch fire if they touch a hot
surface.
Do not use water on grease fires. Never pick up
a flaming pan. Turn the controls off. Smother a
flaming pan on a surface unit by covering the pan
completely with a well fitting lid or baking tray. If
available use a multipurpose dry chemical or foam-
type fire extinguisher.
Always turn the surface unit controls off before
removing the pans.
Don’t place utensils on the hob surface when it is in
use. They may become hot and could cause burns.
Never leave the hob unattended at high heat
settings. Pans boiling over can cause smoking
and greasy spills may catch on fire.
Clean the hob with caution. If a wet sponge or
cloth is used to wipe spills on a hot surface unit,
be careful to avoid steam burns. Some cleansers
can produce noxious fumes if applied to a hot
surface.
Never wear loose-fitting or hanging clothes while
using the appliance. Be careful when reaching for
items stored in cabinets over the hob. Flammable
material could be ignited if brought in contact with
a hot surface unit and may cause severe burns.
Do not use unstable saucepans and position the
handles away from the edge of the hotplate.
Babies, toddlers and young children should not
be allowed near the cooker at any time. They
should never be allowed to sit or stand on any
part of the appliance. Teach them not to play
with controls or any other part of the cooker.
Take great care when heating fats and oils, as
they will ignite if they get too hot.
Use a deep fat thermometer whenever possible to
prevent overheating fat beyond the smoking point.
Never store anything of interest to children in
cabinets above a cooker - children climbing on the
cooker to reach them could be seriously injured.
Never leave a chip pan unattended. Always heat
fat slowly, and watch as it heats. Deep fry pans
should be only one third full of fat. Filling the pan
too full of fat can cause spill over when food is
added. If you use a combination of oils or fats in
Clean only parts listed in this guide.
22
Download from Www.Somanuals.com. All Manuals Search And Download.
frying, stir them together before heating, or as
the fats melt.
The specification of this cooker should not be
altered.
Foods for frying should be as dry as possible. Frost
on frozen foods or moisture on fresh foods can
cause hot fat to bubble up and over the sides of
the pan. Carefully watch for spills or overheating
of foods when frying at high or medium high
temperatures. Never try to move a pan of hot fat,
especially a deep fat fryer. Wait until the fat is cool.
This appliance is heavy, take care when moving
it.
When the cooker is not in use ensure that the
control knobs are in the off position.
Do not slide pans across the hob because this can
scratch the glass - the glass is scratch resistant,
not scratch proof. Sharp instruments, rings or
other jewellery and rivets on clothing could
scratch the hob surface.
When the grill is on, do not use the top of the
flue (the slot along the back of the cooker) for
warming plates, dishes, drying tea towels or
softening butter.
Do not use the surface as a cutting board.
Don’t store heavy items above the hob. If they
drop on the hob, they could cause damage.
When using an electrical appliance near the hob, be
sure that the cord of the appliance does not come
into contact with the surface area.
If you find a crack in the hob surface immediately
disconnect the appliance from the supply and
arrange for its repair.
Take care that no water seeps into the appliance
Only certain types of glass, glass-ceramic,
earthenware or other glazed containers are
suitable for hob cooking; others may break
because of the sudden change in temperature.
Use proper pan size-select pans having flat
bottoms large enough to cover the surface unit’s
heating area. The use of undersized pans will
expose a portion of the surface unit to direct
contact and may result in ignition of clothing.
Proper relationship of pans to surface unit will also
improve efficiency.
Do not allow anyone to climb, stand or hang on
any part of the cooker.
Do not use aluminium foil to cover shelves, linings
or the oven roof.
Make sure that your kitchen is well ventilated at
all times. Use extractor fans or hoods when fitted.
Never heat unopened food containers. Pressure
build up may make container burst and cause
injury.
The cooker is designed for cooking foods only
and must not be used for any other purpose.
The oven should NOT be used for heating the
kitchen, not only does this waste fuel but the
control knobs may become overheated.
When the oven is on DO NOT leave the oven door
open for longer than necessary.
23
Download from Www.Somanuals.com. All Manuals Search And Download.
Checking the parts
Installation
Dear Installer
Before you start your installation, please complete
the details BELOW.
If your customer has a problem relating to your
installation they will be able to contact you easily.
Grill pan and trivet
Levelling tool
Thank you
Installer’s Name
Handyrack
Meat tin
Installer’s Company
2 main oven shelves
Tall oven shelves & shelf
supports
Installer’s Telephone number
Regulations
This appliance must be installed by a qualified
electrician to comply with the relevant
regulations and also the local electricity supply
company requirements.
1 large and 3 small
handles
Splash back & Plinth
This appliance is designed for domestic cooking
only. Use for any other purpose could invalidate
any warranty or liability claim.
You will need the following equipment to
complete the cooker installation satisfactorily
Multimeter (for electrical checks)
Steel tape measure
Cross head screwdriver
Spirit level
Cooker levelling tool (provided in
pack)
24
Download from Www.Somanuals.com. All Manuals Search And Download.
A clearance of 130mm is required if the cooker is near a
corner of the kitchen to allow the oven doors to open.
Positioning the Cooker
The diagrams below show the minimum recommended
distance from the cooker to nearby surfaces.
The cooker should not be placed on a base.
Unpacking the Cooker
Do not take any packaging off the cooker until it is directly
in front of the place it is to be installed (unless it will not fit
through a door in its outer packaging).
Cut the banding straps and lift the cardboard box off the
cooker, leaving the cooker standing on the base packaging.
See the loose unpacking sheet.
The hot surround should be level with, or above, any
adjacent work surface. Above hotplate level a gap of 75mm
should be left between each side of the cooker and any
adjacent vertical surface.
Moving the Cooker
The cooker is very heavy. Take great care.
For non-combustible surfaces (such as unpainted metal or
ceramic tiles) this can be reduced to 25mm.
We recommend two people manoeuvre the cooker. Ensure
that the floor covering is firmly fixed, or removed to prevent
it being disturbed when moving the cooker around. You will
need the levelling tool.
A minimum space of 650mm is required between the top of
the hotplate and a horizontal combustible surface.
From the back tilt the cooker forward and remove the rear
half of the polystyrene base pack.
*Any cooker hood should be installed in accordance with
the hood manufacturer’s instructions.
Surfaces of furniture and walls at the sides and rear of
the appliance should be heat, splash and steam resistant.
Certain types of vinyl or laminate kitchen furniture are
particularly prone to heat damage and discolouration.
We cannot accept responsibility for damage caused by
normal use of the cooker to any material that de-laminates
or discolours at temperatures less than 65°C above room
temperature.
Repeat from the front and remove the front half of the poly
base.
LOWER THE TWO REAR ROLLERS.
First fit the levelling tool on the hexagonal adjusting nut as
shown below.
For safety reasons curtains must not be fitted immediately
behind the cooker.
We recommend a gap of 1110mm between units to allow
for moving the cooker. If a flush fit is required, fit the cooker
up to the unit at one side then fit the unit the other side.
Do not box the cooker in; it must still be possible to move
the cooker in and out for cleaning and servicing. The cooker
should not be placed on a base.
Make 10 complete (360º) turns clockwise. (This means
turning and removing the levelling tool 20 times).
25
Download from Www.Somanuals.com. All Manuals Search And Download.
Levelling
You are recommended to use a spirit level on a shelf in one
of the ovens to check for level.
Place the cooker in its intended position taking care not to
twist it within the gap between the kitchen units as damage
may occur to the cooker or the units.
The front feet and rear rollers can be adjusted to level the
cooker. To adjust the height of the rear of the cooker use
the levelling tool supplied to turn the adjusting nuts at the
front bottom corners of the cooker. To set the front feet turn
the bases to raise or lower.
Fit the Handles
Remove the 4mm Allen screws from the doors with the
hexagon key tool. Use the screws to fit the door handles.
Make sure you lower BOTH REAR ROLLERS. There are two
adjusting nuts, one for each roller, at both the front bottom
corners of the cooker.
Unfold the rear edge of pack base tray. Open the grill door
and the Tall oven door. Grip under the facia panel and lift
the front of the cooker.
The handles should be above the fixings.
Fit the plastic blanking plugs to the fixing holes.
Remove the 4mm Allen screws from the top corners of the
fascia and fix the front handrail in position.
Carefully push the cooker backwards off the pack base.
Remove the pack base tray. Position the cooker close to its
final position leaving just enough space to get behind it.
Fitting the splash back
The cooker can be installed with or without the supplied
splashback. To fit the splash follow the instructions below.
Do not use the door handles or control knobs to manoeuvre
the cooker. Use the hotplate and griddle bowl areas.
view from the rear of the cooker
The splash back is fitted using 4 screws in the rear edge
of the flue grille, two at each end. Remove the outer two
screws and loosen the inner pair. Fit the splash over the
inner screws and then refit the outer two screws. (see
figure).
26
Download from Www.Somanuals.com. All Manuals Search And Download.
Current Operated Earth Leakage Breakers
Where the installation is protected by a 30 milliamp
sensitivity residual current device (RCD), the combined
use of your cooker and other domestic appliances may
occasionally cause nuisance tripping. In these instances the
cooker circuit may need to be protected by fitting 100mA
device. This work should be carried out by a qualified
electrician.
Electrical Connection
This appliance must be installed by a qualified electrician
to comply with the relevant regulations and also the local
electricity supply company requirements.
WARNING: THIS APPLIANCE MUST BE EARTHED
Note
The cooker must be connected to the correct electrical
supply as stated on the voltage label on the cooker, through
a suitable cooker control unit incorporating a double pole
switch having a contact separation of at least 3mm in all
poles. This cooker must not be connected to an ordinary
domestic power point.
Fitting the plinth
Loosen the 3 screws along the front bottom edge of the
cooker. Hook the central keyhole over the central screw.
Twist and fit each end keyhole over their respective screws.
Tighten the fixing screws.
The total electrical load of the appliance is approximately
15 kW. The cable size used should be suitable for this load
and comply with all local requirements.
Oven Light
Press the oven light switch and check that the light is
working.
Access to the mains terminal is gained by removing the
electrical terminal cover box on the back panel.
NB. The oven light bulb is not included in the guarantee.
Hobplate
Turn on each plate in turn and check that it heats up.
Grill
Open the grill compartment door. Turn on the grill control
and check that the grill heats up.
Oven check
Set the clock to the time of day
When the clock is first connected the display will flash
(
) and (
) alternately.
Connect the mains cable to the correct terminals for your
electrical supply type. Please note the maximum cable size
is 10mm2 for the 3-pronged links.
To set the clock to read the time of day turn and hold the
Timer knob to the clock symbol and at the same time
turn the Adjusting knob left or right until the clock shows
the time of day. Remember this is a 24 hour clock. Let go of
the Timer knob and it will spring back to the vertical oven
manual setting.
Turn on the oven and check that the oven fan starts to turn
and that the oven starts to heat up. Turn off the oven.
Customer care
Please complete your details in this Guide, inform the user
how to operate the cooker and hand over the Instructions.
Check that the links are correctly fitted and that
the terminal screws are tight.
Thank you.
Secure the mains cable
using the cable clamp.
27
Download from Www.Somanuals.com. All Manuals Search And Download.
SERVICING - WARNING
Disconnect from the electricity before servicing. Check appliance is safe when you have finished.
4
To Remove the Control Panel
Disconnect from electricity supply.
Servicing Notes
Disconnect from electricity supply before commencing
servicing, particularly before removing any of the following:
control panel, side panels, ceramic hob, or any of the
electrical components or cover boxes. Before electrical
reconnection check that the appliance is electrically safe.
Remove the handrail by removing the 2 end bracket fixing
screws.
1. To Remove a Side Panel
Disconnect from electricity supply.
Pull the cooker forward.
Pull off the push fit control panel end caps at each end and
remove the end fixing screws under the end cap.
Pull off all the control knobs. Open the grill and oven doors
and remove the control panel fixing screws underneath the
control panel. The screws directly below the clock are for
the clock fixing bracket - don’t remove them at this stage.
Lift the control panel, pull forward and disconnect the
wiring from the rear.
Pull off the push fit control panel end caps at each end and
remove the end fixing screws under the end cap.
Reassemble in reverse order. When replacing leads refer to
the wiring diagram. Check operation of timer.
Remove the retaining screws for each panel (1 at the front
and 2 at the rear). The lower front retaining screws (one
each side) are situated beneath the lower edge at the front
corners of the side panels
5. To Remove Oven Light Switch
Remove control panel (see 4).
NB The old switch may be destroyed during removal.
Reassemble in reverse order.
Remove switch button and old switch from its bezel by
gripping the switch body behind the control panel and
twisting sharply.
2. To Lift up the Ceramic Hob
Pull the cooker forward.
The switch bezel can then be removed by folding back its
locking wings and pushing forward. Fit the new bezel to the
control panel by first lining up the raised key on its body
with the cut-out in the control panel and pushing it in from
the front. Assemble the new switch to the bezel by lining up
the key sections and pushing home. Fit the new button by
pushing in from the front.
Pull off the push fit control panel end caps at each end and
remove the end fixing screws under the end cap.
Remove the lower front retaining screws (one each side)
situated beneath the lower edge at the front corners of the
side panels.
Swing the side panels to gain access to the hob fixing
screws (1 each side) at the top front of the side uprights.
Remove these screws.
Replace control panel in reverse order and test for correct
operation.
Caution
6. To Remove Electronic Timer
Disconnect from electricity supply.
The ceramic hob material is much more sensitive
to scratches on the underside than the top.
Pull off the timer control buttons and remove the control
panel (See 4). Remove the timer/mounting bracket
assembly from the control panel by removing the two fixing
screws. Remove the timer from its mounting bracket by
depressing the plastic lugs on the timer case, at the same
time pulling the unit forward.
Lift up the ceramic hob at the front and prop in position
with a non-metallic prop.
Take care not to touch or scratch the underside
of the ceramic as this will weaken the material
and cause the top to shatter.
Reassemble in reverse order. When replacing leads refer to
the wiring diagram. Check operation of timer.
3. To replace a hob element.
Lift up the ceramic hob see 2. The elements are now
accessible.
28
Download from Www.Somanuals.com. All Manuals Search And Download.
SERVICING - WARNING
Disconnect from the electricity before servicing. Check appliance is safe when you have finished.
7. To Remove a Thermostat
11. To Change Oven Door Outer Panel
Lift up the ceramic hob top (see 2). Remove control panel
(see 4). Open appropriate oven door and remove oven
furniture.
Right hand oven
Remove thermostat phial cover (2 screws). Unclip the
thermostat phial from the clips in the oven back.
Left hand oven
Pull cooker forward to gain access to the cover box at
the rear of the cooker. Remove the screws securing the
cover and lift clear.
Remove the two plastic blanking plugs from the door
handles. Remove the 4mm Hex headed screws holding the
handle to the door with the hexagon key tool. Remove two
screws from top edge and two from bottom edge of the
door.
Feed the thermostat capillary out of the oven. Disconnect
wiring from thermostat. Remove 2 screws holding
thermostat to mounting panel. Fit new thermostat and
reassemble in reverse order. Ensure that the phial is clipped
to the oven back with the phial centrally positioned
between the clips.
Check operation of thermostat.
8. To Change Grill Controller
Lift up the ceramic hob top (see 2). Remove control
panel (see 4). Disconnect wiring from controller. Remove
2 screws holding controller to mounting panel. Fit new
controller and reassemble in reverse order. Check for correct
operation.
Remove outer door panel. Fit door handle to new panel. Fit
the plastic blanking plugs to the fixing holes.
9. To Remove Grill Outer Door Panel
Open left hand oven door and remove 2 screws from
bottom edge of grill door. Open grill door, support grill door
outer panel and remove two screws from top inner face of
grill door.
Reassemble in reverse order.
The handles should be above the fixings.
Fit panel to door. If replacing the outer panel on the right
hand door (with the Thermodial) take care to make sure the
sensor of the Thermodial is sealed to the door by the rubber
grommet.
10. To Remove an Oven Door
Open oven door and remove Handyrack (where fitted)
by springing one side out of the bracket on the door and
sliding the other side free.
Door is heavy - take care. Open the oven door. Loosen the
two top hinge screws.
Support the weight of the door and remove the screw
nearest the hinge pin. Swing the hinge up and away from
the hinge pin on the door.
Reassemble in reverse order.
Lift the door away from the bottom hinge.
Re-assemble in reverse order.
When replacing the door ensure that the nylon hinge bush
is in position between the hinge pin and the hinge bracket
at the both the bottom and top.
29
Download from Www.Somanuals.com. All Manuals Search And Download.
SERVICING - WARNING
Disconnect from the electricity before servicing. Check appliance is safe when you have finished.
12. To Change Main Oven Door Catch
Remove outer door panel (see 15). Remove screws ‘B’
holding catch assembly to inner door panel. Fit new catch
and reassemble in reverse order.
15. To Remove Oven Inner Back.
Open the oven door. Remove oven furniture. For the Left
hand oven unscrew the 2 thermostat phial fixing screws.
Check correct door operation.
13. To Adjust Main Oven Door Catch Keep
Open oven door, slacken off locknut at base of keep, and
screw in or out as required until required fit is obtained.
Remove the fixings that secure the inner back to the oven rear.
Lift the removable panel away. Re-assemble in reverse
order. Ensure that the retaining fixings are fully tightened.
For the Left hand oven unscrew the 2 thermostat phial
fixing screws. Remove the screws that secure the inner
back to the oven rear. Lift the removable panel away. Re-
assemble in reverse order. Ensure that the retaining fixings
are fully tightened.
16. To Replace an Oven Fan
Disconnect from electricity supply.
Retighten locking nut.
Pull the unit forward to access the cover boxes at the rear of
the appliance. Remove the fixings that secure the cover and
lift it clear. Remove the fan wiring, noting the connection
positions. Remove the inner back as detailed in Section 20.
Hold the fan blades and undo the centre nut (Left hand
thread), brass washers, fan blade and Circlip. Undo the
fixings that retain the fan and remove it from the cavity rear.
Fit the replacement and re-assemble parts in reverse order.
Check that the oven operates satisfactorily.
14. To Change Oven Door Seal
Open oven door. The seal is held in place by small hooks on
the rear face. At the corner pull seal diagonally away from
the door centre until that hook is released. Proceed to the
next hook and release it in a similar way, and so on.
17. To Remove an Oven fan Element
Disconnect from electricity supply.
Remove the inner back as detailed in Section 20. Remove
the fixings that secure the element within the oven and
lift the element away carefully. Disconnect the leads and
connect to the replacement element and re-assemble parts
in reverse order. Check that the oven operates correctly.
18. To Remove Grill Element.
Disconnect from electricity supply.
When fitting new seal, position the seal join at the bottom.
Hook the new seal in one of the corner holes of the door,
and proceed round the door snapping in each hook in turn.
Remove grill pan from grill chamber. From inside grill
compartment remove enamelled front shield from grill
roof, 2 screws and washers. Remove 2 screws and washers
securing the grill element front support. Remove 1 screw
from each of the grill elements and withdraw grill elements
from grill chamber. Disconnect the leads and connect to
the replacement elements and re-assemble parts in reverse
order. Check operation of grill.
30
Download from Www.Somanuals.com. All Manuals Search And Download.
SERVICING - WARNING
Disconnect from the electricity before servicing. Check appliance is safe when you have finished.
19 To Remove the Left hand Oven Bottom and Top
Elements
Disconnect from the electricity supply.
Bottom Element
Pull the cooker forward to access the cover boxes at the rear
of the unit. Remove the fixings that secure the cover and lift
it clear.
Remove the 2 screws ‘A’and allow the plate to drop down.
Remove the 2 screws B, holding the element to the bottom
sheet.
Disconnect the leads, noting their positions.
Withdraw bottom element. Fit the new element and re-
assemble parts in reverse order.
Top Element
Open the Left hand oven door and undo the fixings that
secure the heat shield. Remove the top element bracket
fixings and withdraw element. Replace the element and
re-assemble parts in reverse order. Check that the oven
operates satisfactorily.
20. To change oven light bulb.
Disconnect from the electricity supply.
Remove the oven furniture. Unscrew the bulb.
Fit an Edison screw fitting 15w 125-130v lamp, FOR OVENS.
It must be a special bulb, heat resistant to 300°C
31
Download from Www.Somanuals.com. All Manuals Search And Download.
32
Download from Www.Somanuals.com. All Manuals Search And Download.
33
Download from Www.Somanuals.com. All Manuals Search And Download.
Technical Data
INSTALLER: Please leave these instructions with the User.
DATA BADGE LOCATION : Cooker back, serial number repeater badge below oven door opening.
Dimensions
Overall height
minimum 893mm
maximum 920mm
Overall width
900mm See ‘Positioning of Cooker’
648mm
Overall depth
Space for fixing
See ‘Positioning of Cooker’
650mm
Minimum space above hotplate
Connections
220 - 240V 50Hz
Electric
Hob
Ovens
Fan element
Left hand Multifunction Oven Right hand Fan Oven
2.5kW
1.2kW
1.15kW
1.0kW
2.5kW
Top element
Browning Element
Bottom element
2.3kW
Grill
Maximum total electrical load at 230V
15 kW (approximate total including oven lights, oven fan etc.)
Ovens
Multifunction Forced air convection
Energy efficiency class :
on a scale of A (more efficient) to G (less efficient)
Energy consumption based on standard load
Usable volume (litres)
B
B
0.90kWh
62
0.95kWh
53
Size
Medium
41 minutes
1400cm2
Large
Time to cook standard load
Baking area
49 minutes
790cm2
34
Download from Www.Somanuals.com. All Manuals Search And Download.
Download from Www.Somanuals.com. All Manuals Search And Download.
Download from Www.Somanuals.com. All Manuals Search And Download.
|
