Deluxe
90 Ceramic
Users Guide
&
Installation & Service Instructions
U109360 - 01
Download from Www.Somanuals.com. All Manuals Search And Download.
Contents
User Guide
The Hob
Page 4
Page 6
The Glide - out Grill
The Ovens
Page 7
The Clock
Page 8
Cooking using the timer
Page 9
Multi-Function oven Functions
Main Oven shelves
The Handyrack
Page 10
Page 12
Page 12
Page 13
Page 13
Page 15
Page 16
Page 20
Page 20
Page 22
Page 24
Page 29
Page 32
Page 35
Oven light
Tall oven shelves
Oven cooking guide
Cleaning your cooker
Moving your cooker
Troubleshooting
General Safety Instructions
Installation
Servicing
Technical Data
Circuit Diagram
3
Download from Www.Somanuals.com. All Manuals Search And Download.
The Hob
When you cook on a ceramic hob its very
important to use the right sort of pans...
5
Always lift pans off the hob. Sliding pans may cause marks
and scratches. Always turn the control to the off position
before removing a pan.
1
Use only pans that are suitable for ceramic hobs.
We recommend stainless steel and enamelled steel pans
because pots and pans with copper or aluminium bases
leave traces on the hob that are difficult to remove.
Glass-ceramic cookware is not suitable because of its poor
conductivity.
6
There are indicator lights for each of the cooking areas.
These come on when a hob control is turned on and
stay lit while the surface cools. Always take care before
touching the surface even when it is turned off - it may be
hotter than you think.
2
Pots and pans should have thick, smooth, flat bottoms.
This ensures that there is the maximum heat transfer from
the hob to the pan, making cooking quick and energy
efficient.
Never use a round bottomed Wok even with a stand.
7
The ratings of the cooking areas are shown on the
diagram above.
3
The very best pans have bases that are very slightly
curved in when cold. If you hold a ruler across the bottom
you will see a small gap in the middle. When they heat up
the metal expands and lies flat on the cooking surface.
8
Although the ceramic surface is very strong, a heavy or
sharp falling object (a salt cellar for example) might cause
the surface to crack. If you find a crack in the surface
immediately disconnect the appliance from the supply
and arrange for its repair.
Make sure that the base of the pan is clean and dry to
prevent any residue burning onto the hob panel. This
also helps prevent scratches and deposits (such as lime
specks).
Care should be taken that no water seeps into the
appliance.
4
9
Always use pans that are the same size as (or slightly
larger than) the areas marked on the hob top. Using
smaller pans wastes heat, and any spillage will be burnt
on. Using a lid will help the contents boil more quickly.
The areas marked with two concentric circles have
an inner and an outer element. Turn the control knob
clockwise to heat the whole area for larger pans - turn it
the other way to just heat the inner part for smaller pans.
4
Download from Www.Somanuals.com. All Manuals Search And Download.
Don’t use the hob as a work surface
Don’t drag or slide utensils across the hob surface
Don’t place anything between the base of the pan
and the hob surface (i.e. asbestos mats, aluminium
foil, Wok stand)
Don’t leave utensils, foodstuffs or combustible items
on the hob when it is not in use. (e.g. tea towels,
frying pans containing oil)
Don’t place plastic or aluminium foil, or plastic
containers on the hob
Don’t leave the hob zones switched on unless being
used for cooking
Don’t place large preserving pans or fish kettles
across two heating zones
Don’t place utensils partly covering a heating zone.
Always place utensils centrally.
Never allow anyone to climb or stand on the hob.
10
Never cook directly on the surface.
The kind of pan you use and the quantity of food
affects the setting required. Higher settings are
required for larger quantities of food.
Naturally, the surface must be washed after use in
order to prevent it from becoming scratched or dirty.
When cooking on the hob you may see the hob area
you are using switch off and on. This is caused by a
safety device that limits the temperature of the hob.
It is quite normal, especially when cooking at high
temperatures. If it happens a lot with a particular
pan however it may mean the pan is not suitable
– perhaps too small or too uneven - for a ceramic hob.
Sugar spillage will permanently damage the hob and
therefore must be cleaned off with care immediately.
Never let sugar spillage cool before trying to remove
it.
If sugar or foods with high sugar content, aluminium
foil or plastic items are accidentally allowed to melt
on the hob surface remove them immediately from
the hot cooking area using a scraper to avoid any
possible damage to the surface. See ‘Cleaning your
cooker’.
Never cut directly on the cooking surface.
Don’t cook directly on the hob surface i.e. without a
pan or utensil
5
Download from Www.Somanuals.com. All Manuals Search And Download.
The neon indicator light by the grill control will come
on.
The Glide-out Grill
Caution: Accessible parts may be hot when the
For best results preheat for 2 minutes with the grill
pan in position. After placing your food on the grill
pan grid, slide in the grill carriage. Adjust the heat to
suit by turning the knob.
grill is in use. Young children should be kept away.
Before using the grill for the first time, make sure
that all packing materials have been removed
and then to dispel manufacturing odours, turn on
the grill and run for 30 minutes with the grill pan
in position, pushed fully back, and the grill door
open.
Make sure the grill carriage is pushed right in.
Never close the grill door when the grill is on.
The grill pan grid can be turned over to give two
grilling positions.
Make sure the room is well ventilated to the
outside air, by opening windows or turning on a
cooker hood for example. We recommend that
people with respiratory or allergy problems
should vacate the area for this brief period.
Don’t leave the grill on for more than a few moments,
without the grill pan underneath it.
Using the grill
Open the grill door and pull the grill pan carriage
forward using the handle.
For best results, especially with toast, preheat the
grill with the grill pan in the cooking position for two
minutes before use.
Before you remove any of the grill parts for cleaning
make sure that they are cool or use oven gloves.
The grill trivet can be removed and the food placed
on it while you are waiting for the grill to preheat.
The grill pan and grill pan carriage can be easily
removed for cleaning. See the ‘Cleaning your cooker’
section of these instructions.
When you pull the grill pan forward is the wide rim at
the front? It’s important that the wider part is at the
front.
The grill pan gets very hot when the grill is on.
Don’t touch the pan or trivet unless you are sure it
is cool.
After placing your food on the grill grid, slide the grill
carriage into the grill chamber. Make sure it is pushed
right in.
The grill has two elements that allow either the whole
area of the pan to be heated or just the right hand
half.
To heat the whole grill, turn the knob clockwise.
To heat the right hand half turn it anticlockwise.
6
Download from Www.Somanuals.com. All Manuals Search And Download.
The Ovens
During use the appliance becomes hot. Care should
be taken to avoid the touching heating elements
inside the oven.
Before using for the first time, to dispel
manufacturing odours, turn the ovens to 230°C
and run for an hour. To clear the smell, make sure
the room is well ventilated to the outside air, by
opening windows or turning on a cooker hood
for example. We recommend that people with
respiratory or allergy problems should vacate the
area for this brief period.
The fans in both ovens circulate hot air continuously,
which means faster more even cooking.
The clock must be set to the time of day before the
right hand fan oven will work. See ‘The Clock’section
for instructions on setting the time of day.
Turn the oven knob to the temperature you need.
The recommended cooking temperatures for a fanned
oven are generally lower than a non-fanned oven.
Whole chickens and large joints of meat should be
defrosted in the refrigerator. Do not defrost in a warm
oven or whilst the adjoining oven is hot.
The oven indicator light will glow until the oven has
reached the temperature you selected. It will then cycle
on and off during cooking.
During cooking, food naturally produces steam,
particulary when cooking foods with high water content
(e.g. oven chips). There may be some steam visible at the
grille at the rear of the hotplate. This is perfectly normal.
As this steam can condense to water droplets on the
cool outer trim of the oven, it may be necessary during
cooking to wipe away any moisture with a soft cloth. This
will also help to prevent soiling and discolouration of the
oven exterior by cooking vapours.
7
Download from Www.Somanuals.com. All Manuals Search And Download.
The Clock
You can use the timer to turn the left hand Main Oven
on and off. The clock must be set to the time of day
before the right hand fan oven will work.
To stop automatically
Use when you have started the oven manually.
Press and hold the Stop
Time (
) button.
To set the time of day
At the same time press (-) or (+) until your required
‘Stop Time’shows. AUTO will show in the display.
When your cooking is finished the beeper sounds.
TURN THE OVEN KNOB TO 0 FIRST, then press once
to stop the beep, press again to return to manual
cooking.
Press and hold as above. At the same time, press (-) or
(+) until the correct time shows. Don’t forget it’s a 24
hour clock. If you make a mistake or press the wrong
button, turn off the power supply for a minute or two
and start again.
To start and stop the oven
automatically
To time something that’s cooking
(minute minder)
Before you set the clock, you must have two numbers
clearly in mind.
Press and hold the
Minute Minder ( ).
The ‘Cook Time’, which is the period of time you
want the oven to cook.
The ‘Stop Time’, which is the time of day you
want the oven to stop cooking.
You cannot set a start time directly - this is set
automatically by setting the cooking period and stop
time.
At the same time press
(-) or (+) until the time
you want to cook for is
shown.
Press and hold the Cook
Time (
) button. At
the same time press (-)
or (+) until your required
‘cook period’shows.
You can check time remaining by pressing
cancel the beeper by pressing
and
Press and hold the Stop
Time (
) button.
At the same time press
(-) or (+) until your
required ‘stop time’
shows.
AUTO will show in the
display.
Set the oven to the required temperature. When
your cooking is finished the beeper sounds. TURN
THE OVEN KNOB TO 0 (off) FIRST, then press once
to stop the beep, press again to return to manual
cooking.
8
Download from Www.Somanuals.com. All Manuals Search And Download.
If you are out, don’t worry about the beeper going
off, it stops after a while. When you return, TURN THE
OVEN KNOB TO 0 (off) FIRST, then press twice, to
return to manual cooking.
Press the ‘+’button
once. The key symbol ( )
goes out and ‘On’shows
on the display.
AUTO is showing, you want to reset to
manual cooking.
Let go of the buttons
When cancelling an automatic setting, any cooking
time already set must be returned to 0.00 before you
can return to manual, by pressing the button.
After a few seconds the display will revert to show the
time of day.
Clock Special Features
Key Lock
The oven and the clock oven control functions can
now be used normally.
When the key lock is activated, the clock can be
operated as usual but the oven is locked and will not
come on. This means that your child could select a
cook program but the program will not be activated
and oven will not be switched on.
Cooking using the timer
The timer can control the left hand Main oven only.
You can set the oven to turn on any time over the
following 24 hour period
To activate the key lock
Make sure that the clock is in manual mode and
cancel any active programs.
If you want to cook more than one dish, choose
dishes that require approximately the same time.
However, dishes can be ‘slowed down’ slightly by
using small containers and covering them with
aluminium foil, or ‘speeded up’ slightly by cooking
smaller quantities or placing in larger containers.
Hold the
Minute Minder ( ) and
Cooktime (
) buttons
for about 8 seconds.
Very perishable foods such as pork or fish should be
avoided if a long delay period is planned, especially in
hot weather.
‘On’will appear on the
display.
Don’t place warm food in the oven.
Don’t use an oven already warm.
Don’t use if an adjoining oven is warm.
Press the ‘+’button
once.
The key symbol ( ) and
‘Of’will appear on the
display. Let go of the
buttons.
Avoid using wine or beer if there is a delay period, as
fermentation may take place.
To avoid curdling, cream should be added to dishes
just before serving.
The clock oven control
functions are now
locked.
Fresh vegetables, which may discolour during a delay
period, should be coated in melted fat or immersed in
a water and lemon juice solution.
After a few seconds the
display will revert to
show the time of day
and the key symbol ( ).
Fruit pies, custard tarts or similar wet mixtures on top
of uncooked pastry are only satisfactory if there is a
short delay period. Dishes containing leftover cooked
meat or poultry should not be cooked automatically
if there is a delay period.
To turn off the key lock
Hold the
Minute Minder ( ) and
Cooktime (
) buttons
for about 8 seconds.
‘Of’will appear on the
display.
9
Download from Www.Somanuals.com. All Manuals Search And Download.
Whole poultry must be thoroughly defrosted before
placing in the oven.
Multi-function oven functions
Check that meat and poultry are fully cooked
before serving.
The Multi-function oven has many varied uses. We
suggest you keep a careful eye on your cooking until
you are familiar with each function. Remember - not
all functions will be suitable for all food types.
Both Ovens
Before using for the first time, to dispel
manufacturing odours turn the ovens to 230°C
and run for an hour. To clear the smell make sure
the room is well ventilated to the outside air, by
opening windows for example.
Rapid Response
The Rapid Response setting enables you to
pre-heat the oven faster than normal. It uses the
fan oven element with additional heat from one of
the elements in the top of the oven. Rangemaster
fan ovens heat up quickly; but the Rapid Response
feature speeds this process up enabling you to
commence cooking sooner.
Both ovens are fanned ovens. The fan circulates hot
air continuously which results in faster heat transfer
to the food.
The wire shelves should always be pushed firmly to
the back of the oven.
To use the Rapid Response feature, simply turn the
function control knob to R and set the temperature
you require. The light on the control panel adjacent
to the R symbol will come on. When temperature is
reached, the light will go out as will the element at
the top of the oven. The fan element and oven fan
will then continue to maintain your chosen oven
temperature.
Baking trays meat tins etcetera should be placed level
centrally on the oven’s wire shelves. Keep all trays
and containers away from the sides of the oven, as
overbrowning of the food may occur.
For even browning, the maximum recommended size
of a baking tray is 340mm by 340mm for the main
oven and 230mm by 320mm for the Tall oven.
Should you choose to place food into the cold oven
prior to cooking whilst using the Rapid Response
function, ensure that cakes etc. are not positioned
too near the top of the oven.
Cooking high moisture content foods can create a
‘steam burst’, when the oven door is opened. When
opening the oven stand well back and allow any
steam to disperse.
As with any cooking, particularly poultry, meat and
ready meals, be sure the food is piping hot before
serving.
When the oven is on, don’t leave the door open for
longer than necessary, otherwise the knobs may get
very hot.
•
Always leave a ‘fingers width’between dishes on
the same shelf. This allows the heat to circulate
freely around them.
Defrost
This function operates the fan to circulate cold
air only. No heat is applied. This enables small items
such as desserts, cream cakes and pieces of meat, fish
and poultry to be defrosted.
•
The Cook & Clean oven liners (see Cleaning your
cooker) work better when fat splashes are avoided.
Cover meat when cooking.
Defrosting in this way speeds up the process and
protects the food from flies. Pieces of meat, fish and
poultry should be placed on a rack, over a tray to
catch any drips. Be sure to wash the rack and tray
after defrosting.
•
•
•
To reduce fat splashing when you add vegetables
to hot fat around a roast, dry them thoroughly or
brush lightly with cooking oil.
Defrost with the oven door closed.
Large items, such as whole chickens and joints should
not be defrosted in this way. We recommend this be
carried out in a refrigerator.
If you want to brown the base of a pastry dish,
preheat a baking tray for 15 minutes before placing
the dish in the centre of the tray.
Where dishes may boil and spill over during
cooking, place them on a baking tray.
Defrosting should not be carried out in a warm oven
or when an adjoining oven is in use or still warm.
Ensure that dairy foods, meat and poultry are
completely defrosted before cooking.
10
Download from Www.Somanuals.com. All Manuals Search And Download.
Fan oven
Conventional oven (top and base
heat)
This function operates the
fan and the heating element
around it. An even heat is
produced throughout the oven,
allowing you to cook large
amounts quickly.
This function combines the heat from the top and
base elements. It is particularly suitable for roasting
and baking pastry, cakes and biscuits. Food cooked
on the top shelf will brown and crisp faster than on
the lower shelf, because the heat is greater at the top
of the oven than at the base, as in ‘Fan assisted oven’
function. Similar items being cooked will need to be
swapped around for even cooking. This means that
foods requiring different temperatures can be cooked
together, using the cooler zone in the lower half of
the oven and hotter area to the top.
Fan oven cooking is particularly
suitable for baking on three
shelves at one time and is a good
‘all-round’function. It may be necessary to reduce
the temperature by approximately 10°C for recipes
previously cooked in a conventional oven.
If you wish to pre-heat the oven, wait until the
indicator light has gone out before inserting the food.
Browning element
This function uses the element in the top of the
oven only. It is a useful function for the browning or
finishing of pasta dishes, vegetables in sauce and
lasagne, the item to be browned being already hot
before switching to the top element.
Fanned grilling in the oven
This function operates the fan whilst the top
element is on. It produces a more even, less fierce
heat than a conventional grill. For best results, place
the food to be grilled, on a grid over a roasting tin,
which should be smaller than a conventional grill
pan. This allows greater air circulation. Thick pieces
of meat or fish are ideal for grilling in this way, as the
circulated air reduces the fierceness of the heat from
the grill. The oven door should be kept closed whilst
grilling is in progress, so saving energy. You will also
find that the food needs to be watched and turned
less than for normal grilling. Pre-heat this function
before cooking.
Base heat
This function uses the base element only. It
will crisp up your pizza or quiche base or finish off
cooking the base of a pastry case on a lower shelf.
It is also a gentle heat, good for slow cooking of
casseroles in the middle of the oven or for plate
warming.
The Browning and Base heat functions are useful
additions to your oven, giving you flexibility to finish
off items to perfection. With use, you will soon realise
how these functions can combine to extend your
cooking skills.
Fan assisted oven
This function operates the fan, circulating air
heated by the elements at the top and the base of
the oven. The combination of fan and conventional
cooking (top and base heat) makes this function ideal
for cooking large items that need thorough cooking,
such as a large meat roast. It is also possible to bake
on two shelves at one time, although they will need
to be swapped over during the cooking time, as the
heat at the top of the oven is greater than at the base,
when using this function.
This is a fast intensive form of cooking; keep an
eye on the food cooking until you have become
accustomed to this function.
11
Download from Www.Somanuals.com. All Manuals Search And Download.
Main Oven shelves
The Handyrack
The maximum weight that can be held by the
Handyrack is 5.5kg (12lb). It should only be used with
the supplied meat tin, which is designed to fit the
Handyrack. Any other vessel could be unstable.
the shelf guard should be at the back pointing upwards
As well as the flat shelf some models are supplied
with a drop shelf. The drop shelf increases the
possibilities for oven shelf spacing.
The Handyrack fits to the left hand Main Oven door
only. Food cooking on it is easy to attend to, because
it’s accessible when the door is open. It can be fitted
at two different heights. One of the oven shelves
must be removed and the other positioned to suit.
When the Handyrack is used in its highest position,
other dishes can be cooked on the bottom shelf
position of the oven or standing on the base of the
oven
When the Handyrack is used in its lowest position,
other dishes can be cooked on the second shelf
position of the oven or standing on the base of the
oven.
The oven shelves can be easily removed and refitted.
Pull the shelf forward
until the back of the shelf
is stopped by the shelf
stop bumps in the oven
sides.
To fit the Handyrack,
locate one side of it
on the door bracket.
Lift up the front of the
shelf so the back of the
shelf will pass under the
shelf stop and then pull
the shelf forward.
Then spring the
other side out to
clip it onto the
other bracket.
To refit the shelf, line up the shelf with a groove in the
oven side and push the shelf back until the ends hit
the shelf stop. Lift up the front so the shelf ends clear
the shelf stops, and then lower the front so that the
shelf is level and push it fully back.
12
Download from Www.Somanuals.com. All Manuals Search And Download.
Oven light
Press the button to turn on the oven light.
If the Main oven light fails, turn off the power
supply before you change the bulb. See the
‘Troubleshooting’section for details on how to
change the oven light bulb.
Tall oven shelves
The tall oven is supplied with four normal cooking
shelves
and a plate warming shelf.
When using the tall oven you can cook on all four
shelves at the same time; but make sure they are well
spaced out to allow the hot air to circulate.
13
Download from Www.Somanuals.com. All Manuals Search And Download.
The oven control settings and cooking
times given in the table opposite are
intended to be used only as a guide.
Individual tastes may require the
temperature to be altered to provide a
preferred result.
Food is cooked at lower temperature in a
fan oven than in a conventional oven. When
using recipes, reduce the temperature by 10°C
and the cooking time by 5-10 minutes. The
temperature in a fanned oven does not vary
with height in the oven - so you can use any
shelf.
Always leave at least one runner space
between shelves when 2 tier cooking. Place
baking trays, individual cake tins or baking
dishes centrally on the oven shelf. For best
results pre-heat the oven until the oven
indicator light goes out.
14
Download from Www.Somanuals.com. All Manuals Search And Download.
Oven cooking guide
Main & Tall Oven
Food
Temperature
Approximate Cooking Time
FISH
180°C
180°C
180°C
Fillets 15-20mins.
Whole 10mins.per 500g + 10mins.
Steaks according to thickness.
ROAST MEATS
Beef with bone
150°C
190°C
150°C
190°C
170°C
190°C
150°C
190°C
20-25mins. per 500g + 20-25mins.
15-20mins. per 500g + 15-20mins.
30-35mins. per 500g + 30-35mins.
20-25mins. per 500g + 20-25mins.
30-35mins. per 500g + 30-35mins.
25-35mins. per 500g + 25-30mins.
35-40mins. per 500g + 35-40mins.
25-30mins. per 500g + 25-30mins.
Beef without bone
Lamb
Pork
Stuffed and rolled - Add approx. 10 mins. per 500g to above cooking times or cook at 200°C for 20mins. then 160°C for
remainder.
THOROUGHLY THAW FROZEN JOINTS AND POULTRY BEFORE COOKING.
POULTRY
Chicken
150°C
190°C
150°C
190°C
20-25mins. per 500g + 20-25mins.
15-20mins. per 500g + 15-20mins.
20-25mins. per 500g + 20-25mins.
15-20mins. per 500g + 15-20mins.
Turkey
Stuffed Poultry - Cook at 200°C or at 200°C for 20mins. then 160°C for remainder. Prepacked (fresh or frozen) follow
packers cooking times
CASSEROLE
YORKSHIRE PUDDING
CAKES
140°C
200°C
2-4hrs according to recipe
Large tin 30-35mins. Individual 10-20mins.
Very Rich Fruit
Rich fruit (180mm)
Madeira (180mm)
Queen Cakes
Scones
140°C
145°C
150°C
170°C
190°C
170°C
45-50mins. per 500g mixture
21/2-3hrs.
80-90mins.
15-25mins.
10-15mins.
Victoria Sandwich
PASTRY
20-30mins.
Plate Tart
190°C
190°C
190°C
200°C
200°C
100°C
45-50mins. Interchange after 25mins.
35-40mins.
Fruit Pie
Tartlets
15-20mins. according to size.
20-40mins. according to size.
20-30mins.
Puff Pastry
BREAD
MERINGUES
PUDDINGS
2-21/2hrs
Baked Egg Custard
Baked sponge pudding
Milk pudding
150°C
180°C
150°C
45mins.-1hr.
40-45mins.
2-3hrs.
500g is approximately 1lb (1lb 2oz)
15
Download from Www.Somanuals.com. All Manuals Search And Download.
burned-on spills”). If you accidentally melt anything
on the cooking or if you spill foods with a high sugar
content (preserves, tomato sauce, etc.), REMOVE the
spill IMMEDIATELY with a razor scraper, while the
unit is still hot. IMPORTANT: Use an oven glove to
protect your hand from potential burns. Scrape the
major spill or melted material from the cooking zone
and push into a cold area. Then, turn the unit “OFF”
and allow to cool before cleaning further. After the
cooking surface cools down and the heat indicator
lights go off, use the daily care procedure as outlined
above.
Cleaning your cooker
Essential information
Before thorough cleaning isolate the electricity
supply. Remember to switch on the electricity supply
before use.
Never use paint solvents, washing soda, caustic
cleaners, biological powders, bleach, chlorine
based bleach cleaners, coarse abrasives or salt.
Don’t mix different cleaning products - they may
react together with hazardous results.
Recommended cleaning materials are shown in
the table at the end of this section.
Cleaning for burned-on spills
Be sure that the heat indicator lights are off and the
hob is cool. Remove excess burned-on substance
with a single-edged razor scraper. Hold the scraper at
approximately a 30° angle to the surface and scrape
off the burned-on matter as you would scrape paint
off of a window.
If you want to move your cooker for cleaning, see the
section called ‘Moving your cooker’.
All parts of the cooker can be cleaned with hot soapy
water - but take care that no surplus water seeps
into the appliance.
For cleaning materials see the ‘Cleaning Table’at the
end of this section.
Grill
The grill pan and grid should be washed in hot soapy
water. After grilling meats or any foods that soil, leave
to soak for a few minutes in the sink immediately
after use. Stubborn particles may be removed from
the grid by using a nylon brush.
IMPORTANT: Take care when using a sharp scraper.
When you have removed as much as possible with
the scraper clean using the daily care procedure as
described above.
Hob
It’s very easy to clean the Hob with a recommended
cleaner.
To remove metal rub-off
CAUTION — Do not use abrasive cleaners or pads,
oven aerosols or pads or stain removers on the
surface.
Sliding pans on the hob - especially aluminium or
copper pans can leave marks on the surface. These
marks often appear like scratches, but can be easily
removed using the procedure described above for
cleaning spills. If the rub-off marks are especially
stubborn, use the cleaning cream together with the
razor scraper, using the technique described above.
Daily care
First of all, be sure that all heat indicator lights are off
and the cooking surface is cool. Apply a small dab,
about the size of a 10p piece, of ceramic cooking
cleaning cream in the centre of each area to be
cleaned. Dampen a clean paper towel and work the
cleaning cream on the cooking surface as if you were
cleaning a window. As a final step, wipe the cooking
surface with a clean, dry paper towel.
Glide out Grill
The grill pan and grid should be washed in hot soapy
water. After grilling meats or any foods that soil, leave
to soak for a few minutes in the sink immediately
after use. Stubborn particles may be removed from
the grid by using a nylon brush. Alternatively the grill
pan can be washed in a dish washer.
Cleaning for spills
For spills and boil-overs that occur while cooking,
turn the unit off and wipe the area surrounding the
hot zone with a clean paper towel. If a spill (other
than a sugary substance) is on the hot zone, do
not clean until the unit is completely cooled down
and follow the instructions below (“Cleaning for
To remove the grill pan support frame, pull the grill
pan forward.
16
Download from Www.Somanuals.com. All Manuals Search And Download.
Lift the grill pan clear of the support frame. The
support frame is held to the side rails by two clips on
each side.
When you have finished, hook the side rails back onto
the sides of the chamber. To refit the frame pull the
side rails forward and for each side in turn support
the side rail and press the frame down into the side
rails. Replace the grill pan.
Control Panel and Doors
The control panel and control knobs should only
be cleaned with a soft cloth wrung out in clean
hot soapy water - but take care that no surplus
water seeps into the appliance. Wipe with a clean
dampened cloth then polish with a dry cloth. The
oven doors should only be cleaned with a soft cloth
wrung out in clean hot soapy water.
For each side, support the side rail with one hand and
with the other hand lift the frame up and out of the
side clips.
Cookers with window doors
On some models the oven door front panel can be
taken off so that the glass panels can be cleaned. If
the top edge of the oven door of your cooker has a
line of holes and there are screws in the side edges
then it can be taken apart for cleaning.
Move the cooker forward to gain access to the
sides (see the ‘Moving the cooker’section of these
instructions).
Open the oven door slightly and remove the front
panel fixing screws from the door sides (two each
side).
For safety, push the side rails back into the grill
chamber.
The side rails can be removed to make cleaning the
grill chamber easer by unhooking them from the grill
chamber sides.
Slides can be wiped clean with soft cloth and mild
detergent.
Do not use any abrasive substance.
some window doors only
DO NOT put the side runners in a dishwasher
Carefully lift off the outer door panel. The inside face
of the glass panels can now be cleaned - take care
not to disturb or wet the door insulation. Please note
that the door is triple glazed but the inner two panels
are fixed and should not be separated. After cleaning
17
Download from Www.Somanuals.com. All Manuals Search And Download.
carefully refit the outer door panel and replace the
side fixing screws.
The Main Oven
The Main oven has panels which have been coated
with a special enamel that partly cleans itself. This
does not stop all marks on the lining, but helps to
reduce the amount of manual cleaning needed.
The Cook & Clean panels work better above
200°C. If you do most of your cooking below this
temperature, occasionally remove the panels and
wipe with a lint free cloth and hot soapy water.
The panels should then be dried and replaced and
the oven heated at 200°C for about one hour. This
will ensure the Cook & Clean panels are working
effectively.
Don’t use steel wool (Brillo) or any other materials
that will scratch the surface. Don’t use oven cleaning
pads.
Removing the Main Oven Linings
Some of the lining panels can be removed for
cleaning and for cleaning behind. Remove the
shelves first.
On some models
the Main oven has a
removable oven roof - if
fitted slide the roof liner
forward and remove.
The side panels of the main oven can be removed.
The Tall Oven
To clean the oven sides slide out the shelves, unhook
the supports from the oven sides and lift out.
18
Download from Www.Somanuals.com. All Manuals Search And Download.
Cleaning Table
Hobplate
Part
Finish
Recommended Cleaning Method
Ceramic Hob
Glass with anodised
aluminium surround.
Remove any dried baked on food deposits with a ceramic hob scraper from
the glass, available from electrical retailers i.e. Curry’s. Clean with HobBrite
Homecare Products or Easy-Do Hobcare Ceramic and Halogen Hob Cleaner and
Conditioner Easy-Do Products Ltd (Curry’s) and polish with a soft cloth.
Do not use cleaners intended for the ceramic hob on the hob surround.
Only use hot soapy water and a soft cloth on the surround.
Outside of cooker
Part
Finish
Recommended Cleaning Method
Door, Door surround and Storage Enamel or paint
Hot soapy water, soft cloth.
Drawer exterior.
Any stubborn stains, remove gently with a liquid detergent.
Stainless Steel
E Cloth (Comet) or Vileda Microfibre Plus All Purpose Cloth
Freudenberg Household Products LP (supermarket)
Sides and Plinth
Painted surface
Hot soapy water, soft cloth.
Splashback/Rear Grille
Enamel or Stainless Hot soapy water, soft cloth. Cream cleaner, with care, if
Steel
necessary.
Control panel
Paint, Enamel or
Stainless Steel
Warm soapy water. Do not use abrasive cleaners on lettering.
Control Knobs/Handles
Oven Door Glass/Glass Lid
Plastic/ Chrome
Toughened glass
Warm soapy water, soft cloth.
Hot soapy water, cream cleaner/scourer if necessary.
Oven and Grill
Part
Finish
Recommended Cleaning Method
Sides, floor & roof of oven -
Enamel
Any proprietary oven cleaner that is suitable for enamel.
NOT COOK & CLEAN OVEN PANELS
(see below)
CAUTION: CORROSIVE/CAUSTIC OVEN CLEANERS - FOLLOW
MANUFACTURERS INSTRUCTIONS. Do not allow contact with
the oven elements.
Cook & Clean Oven Panels (some
models only)
Special enamel
that partly cleans
itself
This surface cleans itself at 200°C and above, or the panels can
be removed and washed with hot soapy water and a nylon
brush. (see ‘The Ovens’in ‘Cleaning your cooker’)
Oven Shelves, Handyrack, Grill
Trivet.
Chrome
An oven interior cleaner that is suitable for chrome. Soap filled
pad. Dishwasher.
Grill Pan/Meat Tin (some models
only)
Enamel
Hot soapy water. Soap filled pad (Brillo). Dishwasher.
Cleaners listed are available from Supermarkets or
electrical retailers as stated. Cleaner manufacturer in
Italics
Regular cleaning is recommended. For easier
cleaning, wipe up any spillages immediately.
To help keep your oven clean, cover meat when
For enameled surfaces use a cleaner that is approved for
use on vitreous enamel. The vitreous enamel association
has a list of approved cleaners. Contact them via their
website www.ive.org.uk..
roasting, with foil or use a roasting bag. Brush
vegetables with fat before placing around the
meat.
19
Download from Www.Somanuals.com. All Manuals Search And Download.
Moving your cooker
Troubleshooting
Switch off the electricity supply.
A crack has appeared in the Hob surface
Disconnect the cooker immediately from the power
supply and arrange for its repair. Don’t use the cooker
until after the repair. See the Customer care leaflet for
how to contact a service person.
The cooker is heavy, two people may be required to
move it. There are two levelling rollers at the back
and also two screw down levelling feet at the front.
My Hob is scratched
Have you used the correct cleaning methods?
Pots and pans with rough bottoms, or coarse particles
(salt or sand) between the pan and the surface of the
hob may cause scratches.
Use the recommended cleaning methods. Make sure
pan bottoms are smooth and clean. Tiny scratches are
not removable but will become less visible in time as
a result of cleaning.
Metal markings on the Hob
Do not slide aluminium or copper pans across the
surface. Marks from aluminium and copper pans as
well as mineral deposits from water or food can be
removed with the cleaning cream.
Note - For illustration purposes, the Dual Fuel
model is shown.
Open the grill door and right hand oven door so that
you can get a good grip on the bottom of the fascia
panel as you move the oven.
Steam is coming from the oven
When cooking foods with a high water content (e.g.
oven chips) there may be some steam visible at the
rear grille. Take care when opening the oven door, as
there may be a momentary puff of steam when the
oven door is opened. Stand well back and allow any
steam to disperse.
The oven fan is noisy
The note of the oven fan may change as the oven
heats up - this is perfectly normal.
What cleaning materials are recommended for the
cooker?
Lift the front of the cooker slightly and pull forward.
Do not move the oven by pulling the door handles
or knobs.
See the ‘Cleaning’section for recommended cleaning
materials. We do not recommend Mr. Muscle, as it
contains chemicals that may damage the surfaces of
your cooker.
Move the oven a bit at a time, checking behind it to
make sure the gas hose is not caught. Make sure both
electricity cable and gas hose have sufficient slack to
move the cooker forward as you go along.
Grill not cooking properly
Are you using the pan and trivet supplied with the
cooker? Is the pan being used on the runners, not
the floor of the compartment? Is the grill tray pushed
fully back to stop?
If a stability chain is fitted, release it as you ease the
cooker out. Don’t forget to refit it when you replace
the cooker.
When you replace the cooker, again check behind to
make sure that the electricity cable and gas hose are
not caught or trapped.
The knobs get hot when I use the oven or the grill,
can I avoid this?
Yes, this is caused by heat rising from the oven or the
grill, and heating them up. Don’t leave the oven door
open. Make sure that the grill pan is pushed right
back to the ‘back stop’when grilling.
20
Download from Www.Somanuals.com. All Manuals Search And Download.
Is the key symbol ( ) showing in the display? See the
Clock section of the instructions for more information
on the key lock feature of the clock.
If there is an installation problem and I don’t get my
original installer to come back to fix it who pays?
You do. Service organisations will charge for their call-
outs if they are correcting work carried out by your
original installer. It’s in your interest to track down
your original installer.
Oven temperature getting hotter as the cooker gets
older
If turning the knob down has not worked or only
worked for a short time then you may need a new
thermostat. This should be fitted by a service person.
Power failure
In the event of a failure in the electrical supply the
hotplate may be lit using a match.
The oven light is not working
The bulb has probably blown. You can buy a
replacement bulb (which is not covered under the
guarantee) from a good electrical shop. Ask for an
Edison screw fitting 15w 240v lamp, FOR OVENS. It
must be a special bulb, heat resistant to 300 °C. See
the HELP leaflet for spares by mail order.
Food is cooking too slowly, too quickly, or burning
Cooking times may differ from your previous
oven. Check that you are using the recommended
temperatures and shelf positions. See the oven
cooking guide. The oven control settings and cooking
times are intended to be used only as a guide.
Individual tastes may require the temperature to be
altered either way, to get the results you want. Try
cooking at a different temperature setting.
Turn off the power supply.
The oven is not cooking evenly
Do not use a tin or baking tray larger than 340mm x
340mm in the Main oven or 232mm x 321mm in the
Tall oven.
Make sure the oven is cool. Open the oven door and
remove the oven shelves.
Unscrew the bulb cover by turning anticlockwise. It
may be very stiff.
If you are cooking a large item, be prepared to turn it
round during cooking.
If two shelves are used, check that space has been
left for the heat to circulate. When a baking tray is put
into the oven, make sure it is placed centrally on the
shelf.
Check that the door seal is not damaged and that the
door catch is adjusted so that the door is held firmly
against the seal.
Taking care to protect your fingers in case the bulb
should shatter, unscrew the old bulb.
A dish of water when placed on the shelf should be
the same depth all over. (For example, if it is deeper
at the back, then the back of the cooker should be
raised up or the front lowered). If the cooker is not
level arrange for your supplier to level it for you.
Screw in the new bulb, screw back the bulb cover.
Turn on the electricity supply and check that the bulb
now lights.
The left hand Main oven not coming on when turned
on manually
Is the power on? Is the clock illuminated?
If not there may be something wrong with the power
supply. Is the cooker supply on at the isolator switch?
Has the time of day been set?
Is the key symbol ( ) showing in the display? See the
Clock section of the instructions for more information
on the key lock feature of the clock.
The left hand Main oven not coming on when
automatic cooking
Timer set correctly but oven knob left OFF by
mistake?
21
Download from Www.Somanuals.com. All Manuals Search And Download.
In the interests of hygiene and safety the cooker
should be kept clean at all times as a build up in fats
and other food stuff could result in a fire.
General Safety Instructions
The cooker must be installed by a qualified electrician
in accordance with the installation instructions. It
should be serviced by a qualified service engineer
and only approved spare parts used. Have the
installer show you the location of the cooker control
switch. Mark it for easy reference. Always allow the
cooker to cool and then switch off at the mains and
before cleaning or carrying out any maintenance
work, unless specified otherwise in this guide.
We recommend that you avoid wiping any surface
unit areas until they have cooled and the indicator
light has gone off. Sugar spills are the exception to
this. Please see ‘Cleaning your cooker’. When the
hob is cool, use only the recommended cleaning
cream to clean the hob.
To avoid possible damage to the cooking surface,
do not apply the cleaning cream to the glass surface
when it is hot. Read and follow all instructions
and warnings on the cleaning cream labels. After
cleaning, use a dry cloth or paper towel to remove
any cleaning cream residue.
All parts of the cooker become hot with use and
will retain heat even after you have stopped
cooking.
Take care when touching the hob especially the
marked cooking areas. The glass surface of the hob
will retain heat after the controls have been turned
off. To minimize the possibility of burns, always be
certain that the hob controls are in the OFF position
and that the entire glass surface is cool before
attempting to clean the hob.
Avoid heating an empty pan. Doing so may
damage the hob and the pan.
Always keep combustible wall coverings or curtains
etc. a safe distance away from your cooker.
Do not place or store items on top of the glass hob
surface when it is not in use.
Use dry oven gloves when applicable - using damp
gloves might result in steam burns when you touch
a hot surface. Never operate the cooker with wet
hands.
Do not spray aerosols in the vicinity of the cooker
while it is in on.
Do not store or use combustible materials, or
flammable liquids in the vicinity of this appliance.
Do not use a towel or other bulky cloth in place of
a glove. They might catch fire if they touch a hot
surface.
Do not use water on grease fires. Never pick up a
flaming pan. Turn the controls off. Smother a flaming
pan on a surface unit by covering the pan completely
with a well fitting lid or baking tray. If available
use a multipurpose dry chemical or foam-type fire
extinguisher.
Always turn the surface unit controls off before
removing the pans.
Don’t place utensils on the hob surface when it is in
use. They may become hot and could cause burns.
Never leave the hob unattended at high heat
settings. Pans boiling over can cause smoking and
greasy spills may catch on fire.
Clean the hob with caution. If a wet sponge or
cloth is used to wipe spills on a hot surface unit, be
careful to avoid steam burns. Some cleansers can
produce noxious fumes if applied to a hot surface.
Never wear loose-fitting or hanging clothes while
using the appliance. Be careful when reaching for
items stored in cabinets over the hob. Flammable
material could be ignited if brought in contact with a
hot surface unit and may cause severe burns.
Do not use unstable saucepans and position the
handles away from the edge of the hotplate.
Babies, toddlers and young children should not be
allowed near the cooker at any time. They should
never be allowed to sit or stand on any part of the
appliance. Teach them not to play with controls or
any other part of the cooker.
Take great care when heating fats and oils, as they
will ignite if they get too hot.
Use a deep fat thermometer whenever possible to
prevent overheating fat beyond the smoking point.
Never store anything of interest to children in
cabinets above a cooker - children climbing on the
cooker to reach them could be seriously injured.
Never leave a chip pan unattended. Always heat fat
slowly, and watch as it heats. Deep fry pans should
be only one third full of fat. Filling the pan too full
of fat can cause spill over when food is added. If
you use a combination of oils or fats in frying, stir
them together before heating, or as the fats melt.
Clean only parts listed in this guide.
22
Download from Www.Somanuals.com. All Manuals Search And Download.
Foods for frying should be as dry as possible. Frost
on frozen foods or moisture on fresh foods can cause
hot fat to bubble up and over the sides of the pan.
Carefully watch for spills or overheating of foods
when frying at high or medium high temperatures.
Never try to move a pan of hot fat, especially a deep
fat fryer. Wait until the fat is cool.
scratch proof. Sharp instruments, rings or other
jewellery and rivets on clothing could scratch the
hob surface.
Do not use the surface as a cutting board.
Don’t store heavy items above the hob. If they drop
on the hob, they could cause damage
When the grill is on, do not use the top of the flue
(the slot along the back of the cooker) for warming
plates, dishes, drying tea towels or softening butter.
When using an electrical appliance near the hob, be
sure that the cord of the appliance does not come
into contact with the surface area.
If you find a crack in the hob surface immediately
disconnect the appliance from the supply and
arrange for its repair.
Take care that no water seeps into the appliance
Only certain types of glass, glass-ceramic,
earthenware or other glazed containers are
suitable for hob cooking; others may break
because of the sudden change in temperature.
Use proper pan size-select pans having flat bottoms
large enough to cover the surface unit’s heating area.
The use of undersized pans will expose a portion of
the surface unit to direct contact and may result in
ignition of clothing. Proper relationship of pans to
surface unit will also improve efficiency.
Do not allow anyone to climb, stand or hang on
any part of the cooker.
Do not use aluminium foil to cover shelves, linings or
the oven roof.
Make sure that your kitchen is well ventilated at all
times. Use extractor fans or hoods when fitted.
Never heat unopened food containers. Pressure build
up may make container burst and cause injury.
The cooker is designed for cooking foods only and
must not be used for any other purpose.
The oven should NOT be used for heating the kitchen,
not only does this waste fuel but the control knobs
may become overheated.
When the oven is on DO NOT leave the oven door
open for longer than necessary.
The specification of this cooker should not be altered.
This appliance is heavy, take care when moving it.
When the cooker is not in use ensure that the control
knobs are in the off position.
Do not slide pans across the hob because this can
scratch the glass - the glass is scratch resistant, not
23
Download from Www.Somanuals.com. All Manuals Search And Download.
Installation
Dear Installer
Before you start your installation, please complete the details BELOW.
If your customer has a problem relating to your installation they will be able to
contact you easily.
Thank you
Installer’s Name
Installer’s Company
Installer’s Telephone number
Regulations
This appliance must be installed by a qualified electrician to comply with
the relevant regulations and also the local electricity supply company
requirements.
You will need the following equipment to complete the cooker installation satisfactorily
Multimeter (for electrical checks)
Cooker levelling tool (provided in pack)
You will also need the following tools:
1. Electric drill
2. Masonry drill bit (only required if fitting the cooker on a
stone or concrete floor)
3. Rawlplugs (only required if fitting the cooker on a stone
or concrete floor)
4. Steel tape measure
5. Cross head screwdriver
6. Flat head screwdriver
7. Spirit level
8. Pencil
9. Adjustable spanner
10. Screws for fitting stability bracket
24
Download from Www.Somanuals.com. All Manuals Search And Download.
allows for some protection of your hand as you open the
door.
Positioning the Cooker
The diagrams below show the minimum recommended
distance from the cooker to nearby surfaces.
The cooker should not be placed on a base.
Unpacking the Cooker
Do not take any packaging off the cooker until it is
directly in front of the place it is to be installed (unless it
will not fit through a door in its outer packaging).
Cut the banding straps and lift the cardboard box off
the cooker, leaving the cooker standing on the base
packaging. See the loose unpacking sheet.
The hotplate surround should be level with, or above,
any adjacent work surface. Above hotplate level a gap
of 75mm should be left between each side of the cooker
and any adjacent vertical surface.
Checking the parts
For non-combustible surfaces (such as unpainted metal
or ceramic tiles) this can be reduced to 25mm.
Levelling tool and Allen keys
1 flat oven shelf and 1 drop shelf
A minimum space of 650mm is required between the
top of the hotplate and a horizontal combustible surface.
Tall oven shelves & shelf supports Handyrack
Meat tin
Grill pan and trivet
*Any cooker hood should be installed in accordance with
the hood manufacturer’s instructions.
Surfaces of furniture and walls at the sides and rear of
the appliance should be heat, splash and steam resistant.
Certain types of vinyl or laminate kitchen furniture are
particularly prone to heat damage and discolouration.
We cannot accept responsibility for damage caused
by normal use of the cooker to any material that de-
laminates or discolours at temperatures less than 65°C
above room temperature.
For safety reasons curtains must not be fitted
immediately behind the cooker.
We recommend a gap of 910mm between units to allow
for moving the cooker. Do not box the cooker in; it must
be possible to move the cooker in and out for cleaning
and servicing.
A clearance of 130mm is required if the cooker is near a
corner of the kitchen to allow the oven doors to open.
The actual opening of the doors is slightly less but this
25
Download from Www.Somanuals.com. All Manuals Search And Download.
Unfold the rear edge of pack base tray. Open the grill
door and the Tall oven door. Grip under the facia panel
and lift the front of the cooker.
Moving the Cooker
The cooker is very heavy. Take great care.
We recommend two people manoeuvre the cooker.
Ensure that the floor covering is firmly fixed, or removed
to prevent it being disturbed when moving the cooker
around. You will need the levelling tool.
Remove the polystyrene base pack. From the front tilt
the cooker forward and remove the front half of the
polystyrene base.
Carefully push the cooker backwards off the pack base.
Remove the pack base tray. Position the cooker close to
its final position leaving just enough space to get behind
it.
Repeat from the back and remove the rear half of the
poly base.
LOWER THE TWO REAR ROLLERS.
First fit the levelling tool on the hexagonal adjusting nut
as shown below.
Do not use the door handles or control knobs to
manoeuvre the cooker. Use the hotplate and griddle
bowl areas.
Make 10 complete (360º) turns clockwise. (This means
turning and removing the levelling tool 20 times).
Levelling
You are recommended to use a spirit level on a shelf in
one of the ovens to check for level.
Place the cooker in its intended position taking care not
to twist it within the gap between the kitchen units as
damage may occur to the cooker or the units.
The front feet and rear rollers can be adjusted to level
the cooker. To adjust the height of the rear of the cooker
use the levelling tool supplied to turn the adjusting nuts
at the front bottom corners of the cooker. To set the front
feet turn the bases to raise or lower.
Fitting a stability bracket
A stability bracket or chain (not supplied by with the
cooker) should be fitted when the cooker is connected
to a flexible gas supply.
When fitting a stability bracket read these instructions
together with the leaflet supplied with the bracket.
Make sure you lower BOTH REAR ROLLERS. There are
two adjusting nuts, one for each roller, at both the front
bottom corners of the cooker.
26
Download from Www.Somanuals.com. All Manuals Search And Download.
1. Place the cooker in its intended position and level
the cooker.
Access to the mains terminal is gained by removing
the electrical terminal cover box on the back panel.
Connect the mains cable to the correct terminals for
your electrical supply type (see fig.). Check that the links
are correctly fitted and that the terminal screws are tight.
Secure the mains cable using the cable clamp.
2. Draw a pencil line 70mm from the front edge of the
levelling feet.
3. Mark the centre line for the bracket by measuring
550mm from the left hand side of the cooker.
4. Move the cooker forward.
These appliances are of type X with regard to protection
against over heating of the surrounding surfaces.
5. Measure back from the pencil line 500mm to locate
the front edge of the bracket. Position the bracket
so that it is away from centreline of the cooker to
reduce the possibility that it will trap the electrical
connection cable. Fix the bracket to the floor.
Hotplate
Check each burner in turn. Push in tap and turn to the
large flame symbol. Press ignition switch on facia panel..
6. Measure the height from floor level to engagement
edge in back of cooker. Add 3mm to this dimension
and assemble the stability bracket to this height. (i.e.
from floor level to underside of the top member) and
ensure the bracket does not foul the oven burner
assembly.
Oven check
The clock must be set to the time of day before the left
hand Main oven will work.
Press and hold as above.
At the same time, press - or + until the correct time
shows.
Don’t forget it’s a 24 hour clock.
If you make a mistake or press the wrong button, turn off
the power supply for a minute or two and start again.
Electrical Connection
This appliance must be installed by a qualified electrician
to comply with the relevant Institute of Electrical
Engineers (I.E.E.) regulations and also the local electricity
supply company requirements.
Turn on the ovens. Check that the oven fans start to turn
and that the ovens start to heat up. Turn off the ovens.
Fitting the plinth
Fit the inner plinth to the bottom front of the cooker
using the 5 screws provided.
WARNING: THIS APPLIANCE MUST BE EARTHED
Note
The cooker must be connected to the correct electrical
supply as stated on the voltage label on the cooker,
through a suitable cooker control unit incorporating
a double pole switch having a contact separation
of at least 3mm in all poles. This cooker must not be
connected to an ordinary domestic power point.
Fit the outer plinth (2 screws 1 each end) to the inner
plinth. The height of the outer plinth can be adjusted by
sliding it up or down via the slotted hole.
27
Download from Www.Somanuals.com. All Manuals Search And Download.
Door adjustment
Please check the aligment of the doors. The left hand
Main oven has adjustible hinges
To Adjust the Oven Door Angle
The door bottom hinge can be adjusted to alter the
angle of the door.
Loosen the bottom hinge fixing screws and use the
notch and a flat bladed screwdriver to move the position
of the hinge to set the hinge position.
Retighten the hinge screws.
Effect of hinge adjustment – exaggerated for clarity
Centre line of hinge pin
Oven door omitted for clarity
Customer care
Please complete your contact details in the front of
this section. Please inform the user how to operate the
cooker and hand over the instruction pack.
Thank you.
28
Download from Www.Somanuals.com. All Manuals Search And Download.
WARNING - SERVICING TO BE CARRIED OUT ONLY BY AN AUTHORISED PERSON
Disconnect from electricity before servicing. Check appliance is safe when you have finished.
Servicing Notes
Disconnect from electricity supply before
commencing servicing, particularly before removing
any of the following: control panel, side panels,
ceramic hob, or any of the electrical components or
cover boxes. Before electrical reconnection check that
the appliance is electrically safe.
Pull off all the control knobs. Open the grill and oven doors
and remove the control panel fixing screws underneath the
control panel. The screws directly below the clock are for
the clock fixing bracket - don’t remove them at this stage.
Lift the control panel, pull forward and disconnect the
wiring from the rear.
1. To Remove a Side Panel
Disconnect from electricity supply.
Reassemble in reverse order. When replacing leads refer to
the wiring diagram. Check operation of timer.
Pull the cooker forward.
Pull off the push fit control panel end caps at each end and
remove the end fixing screws under the end cap.
5. To Remove Oven Light Switch
Remove the retaining screws for each panel (1 at the front
and 2 at the rear). The lower front retaining screws (one
each side) are situated beneath the lower edge at the front
corners of the side panels
Remove control panel (see 4).
NB The old switch may be destroyed during removal.
Remove switch button and old switch from its bezel by
gripping the switch body behind the control panel and
twisting sharply.
Reassemble in reverse order.
The switch bezel can then be removed by folding back its
locking wings and pushing forward. Fit the new bezel to the
control panel by first lining up the raised key on its body
with the cut-out in the control panel and pushing it in from
the front. Assemble the new switch to the bezel by lining up
the key sections and pushing home. Fit the new button by
pushing in from the front.
2. To Lift up the Ceramic Hob
Pull the cooker forward.
Unscrew the 2 screws which are located at the rear of either
side of the cooker underneath the grill trim
Push the hob backwards to release the front catchment
bracket.
Replace control panel in reverse order and test for correct
operation.
Lift the hob.
Hold the hob in place using the rod attached to the
underside of the hobplate, by locating the loose end into
the central hole in the top of the inner control panel.
6. To Remove Electronic Timer
Disconnect from electricity supply.
Pull off the timer control buttons and remove the control
panel (See 4). Remove the timer/mounting bracket
assembly from the control panel by removing the two fixing
screws. Remove the timer from its mounting bracket by
depressing the plastic lugs on the timer case, at the same
time pulling the unit forward.
Caution
The ceramic hob material is much more sensitive
to scratches on the underside than the top.
Lift up the ceramic hob at the front and prop in position
with a non-metallic prop.
Reassemble in reverse order. When replacing leads refer to
the wiring diagram. Check operation of timer.
Take care not to touch or scratch the underside of the
ceramic as this will weaken the material and cause
the top to shatter.1.
Panel
To Remove a Side
7. To Remove a Thermostat
Lift up the ceramic hob top (see 2). Remove control panel
(see 4). Open appropriate oven door and remove oven
furniture.
3. To replace a hob element.
Lift up the ceramic hob see 2. The elements are now
accessible.
RH oven
Remove thermostat phial cover (2 screws). Unclip
the thermostat phial from the clips in the oven
back.
4
To Remove the Control Panel
Disconnect from electricity supply.
Remove the handrail by removing the 2 end bracket fixing
screws.
LH oven
Pull cooker forward to gain access to the cover
box at the rear of the cooker. Remove the screws
securing the cover and lift clear.
29
Download from Www.Somanuals.com. All Manuals Search And Download.
WARNING - SERVICING TO BE CARRIED OUT ONLY BY AN AUTHORISED PERSON
Disconnect from electricity before servicing. Check appliance is safe when you have finished.
Feed the thermostat capillary out of the oven. Disconnect
wiring from thermostat. Remove 2 screws holding
thermostat to mounting panel. Fit new thermostat and
reassemble in reverse order. Ensure that the phial is clipped
to the oven back with the phial centrally positioned
between the clips.
Check correct door operation.
Check operation of thermostat.
8. To Change Grill Controller
Lift up the ceramic hob top (see 2). Remove control
panel (see 4). Disconnect wiring from controller. Remove
2 screws holding controller to mounting panel. Fit new
controller and reassemble in reverse order. Check for correct
operation.
13. To Change Oven Door Seal
Open oven door. The seal is held in place by small hooks on
the rear face. At the corner pull seal diagonally away from
the door centre until that hook is released. Proceed to the
next hook and release it in a similar way, and so on. Use
force if the hooks are stiff, as the old seal will be discarded.
9. To Remove Grill Door
Remove the left hand side panel (see 1). Remove the control
panel (see 4). Remove the centre cover strip (5 screws, 2 top,
2 bottom, 1 in middle). Remove the two countersunk screws
(1 each side) securing the grill hinge arms to the front of the
grill chamber.
NOTE: The arms are spring tensioned. Carefully remove the
grill door. Retain the gaskets.
Reassemble in reverse order ensuring that the gasket is
fitted between the hinge arm and the front of the grill
chamber.
When fitting new seal, position the seal join at the bottom.
Hook the new seal in one of the corner holes of the door,
10. To Remove Main Oven Door
Open oven door and remove Handyrack (where fitted)
by springing one side out of the bracket on the door and
sliding the other side free. Support the door and remove
the two screws securing the upper hinge and packing to
the cooker front. Remove the door from the lower hinge by
lifting slightly and moving outwards.
and proceed round the door snapping in each hook in turn.
14. To Adjust the Main Oven Door Catch Keep
Open oven door, slacken off
locknut at base of keep, and
screw in or out as required until
required fit is obtained.
Reassemble in reverse order.
11. To Change Main Oven Door Outer Panel
Move the cooker forward to gain access to the sides.
Retighten locking nut.
Open the oven door slightly and remove the front panel
fixing screws from the door sides (two each side).
15. To Change Tall Oven Door Outer Panel
Remove oven door see 12. Lay door face down on a
suitable surface and remove 2 screws from bottom edge
of door and 2 screws from inside face of door.
Remove outer door panel. Remove door handle by
unscrewing 2 screws. Remove 2 cross-headed screws
holding door handle fixing bracket to door panel. Fit
door handle bracket and door handle to new panel.
Carefully lift off the outer door panel.
Fit panel to door. Reassemble in reverse order.
Remove door handle from panel by unscrewing 2 retaining
nuts. Fit door handle to new panel
16. To Change Tall Oven Door Magnetic Latch
Fit panel to door. Reassemble in reverse order.
Remove the control panel (see 1).
Remove the plinth (3 screws) and the central vertical
cover (5 screws). Prize the retaining clip off the magnet
unit. Fit new unit and retaining clip.
12. To Change Main Oven Door Latch
Remove outer door panel (see 15). Remove screws ‘B’
holding latch assembly to inner door panel. Fit new catch
and reassemble in reverse order.
Reassemble in reverse order.
30
Download from Www.Somanuals.com. All Manuals Search And Download.
WARNING - SERVICING TO BE CARRIED OUT ONLY BY AN AUTHORISED PERSON
Disconnect from electricity before servicing. Check appliance is safe when you have finished.
Check correct door operation.
20 To Remove an Oven element Thermal Cut-Out.
Disconnect from the electricity supply.
17. To Remove Grill Element.
Pull the cooker forward to gain access to the cover
box. Undo the cover screws and lift clear. The cutout
is located on the earth plate beside the oven element
connections. Disconnect the cutout wiring. Undo the
fixings that secure the cutout to the earth plate and
remove. Fit replacement control and re-assemble in
reverse order.
Disconnect from electricity supply.
Remove grill pan from grill chamber. From inside grill
compartment remove enamelled front shield from
grill roof, 2 screws and washers. Remove 2 screws
and washers securing the grill element front support.
Remove the screws from the grill elements.
Lift elements out carefully, disconnect the leads from
the element terminals noting their position. If it is not
possible to disconnect the leads in this way, pull cooker
forward to gain access to the rear, remove screws
securing the electric cover to the back sheet and remove
cover and disconnect the terminals from the rear.
21. To Remove Oven Element.
Disconnect from electricity supply.
Remove oven inner back (see 18).
Remove 2 screws from the
top of the element and 1 from
the bottom of the element
in side the oven. Lift element
out carefully, disconnect the
terminals connected to the
element noting their positions.
Fit new elements, reassemble in reverse order. Check
operation of grill.
18. To Remove an Oven Inner Back.
Open the oven door and remove the screws and washers
securing the inner back to the back of the oven.
If it is not possible to disconnect
the leads in this way, pull cooker
forward to gain access to the
rear.
Remove screws securing the electric cover to the back
sheet and remove cover and disconnect the terminals
from the rear.
Fit new element, and reassemble in reverse order. Check
operation of oven.
22. To change oven light bulb.
LH Oven
Remove the oven furniture and side linings. Remove the
oven rear liner.
Carefully lift away the inner back. Reassemble in reverse
order making sure that the 4 screws and washers are
fully tightened.
RH Oven
Remove the oven inner back (see 18). The oven light
cover is now accessible. Unscrew the cover.
19. To Change Fan in Oven.
Unscrew the bulb.
Disconnect from electricity supply.
Fit an Edison screw fitting 15w 240v lamp, FOR OVENS. It
must be a special bulb, heat resistant to 300°C.
Pull cooker forward to gain access to the rear. Remove
screws securing the electric cover to the back sheet and
remove cover. Disconnect the 3 terminals connected to
the fan noting their position. Remove oven inner back
(see 18). Hold the fan blade and remove the centre nut
(left hand thread) 2 brass washers, fan blade and Circlip.
Unscrew fan retaining nuts and washers (3 off each) and
lift the fan away from the rear of the cooker. Fit new fan
and reassemble in reverse order. Check operation of
oven.
31
Download from Www.Somanuals.com. All Manuals Search And Download.
Technical Data
INSTALLER: Please leave these instructions with the User.
DATA BADGE LOCATION : Cooker back, serial number repeater badge below oven door opening.
Country of Destination: GB/IE
Dimensions
Overall height minimum 900mm
maximum 925mm
Overall width 900mm See ‘Positioning of Cooker’
Overall depth 648mm
Space for fixing See ‘Positioning of Cooker’
Minimum space above hotplate 650mm
Ratings
Total Load At 230V 50Hz 15.6kW (approximate total including oven lights, oven fan etc.)
Hob
Main Oven
Tall Oven
Forced air convection
2.5kW
Forced air convection
Ovens
2.5kW
Energy efficiency class on a scale
of A (more efficient) to G (less efficient)
Energy consumption based on standard load
Usable volume (litres)
A
B
0.85kWh
67
0.95kWh
53
Size
Large
38 minutes
1400cm2
Medium
49 minutes
790cm2
Time to cook standard load
Surface area of the grid
2.3kW
Grill
32
Download from Www.Somanuals.com. All Manuals Search And Download.
33
Download from Www.Somanuals.com. All Manuals Search And Download.
Connection shown in circuit diagram is for single phase.
Ratings are for 230V 50Hz
Key to circuit diagram
Colour Code
b Blue
M1Right hand oven thermostat
M2Right hand oven switch block
M3Right Fan oven element 2.5kW
M4Right hand oven fan
E
L
Earth
Live
br Brown
bk black
N Neutral
U Main oven light switch
or Orange
J1 Left hand oven thermostat
J3 Left hand oven switch block
J7 Left Fan oven element 2.5kW
J8 Left hand oven fan
T
P
Main oven light
Neon
r
Red
v
Violet
Q Cut-out
w White
Yellow
g/y Green/Yellow
A1 LH Front Energy Regulator
A2 LH Front Hob
y
K
Clock
H1 Grill energy regulator
B1 LH Rear Energy Regulator
B2 LH Rear Hob
H2 Grill switch block
H3 Right hand grill element 1.15kW
H3 Left hand grill element 1.15Kw
C1 RH Rear Energy Regulator
C2 RH Rear Hob
D1 RH Front Energy Regulator
D2 RH Front Hob
F1 RH Energy Regulator
F2 RH Hob
34
Download from Www.Somanuals.com. All Manuals Search And Download.
b
b
b
b
b
br
b
br
br
bk
br
br
br
br
br
br
bk
b
P1
P1
P1
P1
P1
F1
C1
D1
A1
B1
4
2
4
2
P2
4
2
4
2
4a P2
S2 S1
4
2
r
r
r
r
r
b
b
b
v
b
b
br
P2
P2
4a P2
b
b
V
b
b
bk
bk
S2 S1
S2 S1
bk S2 S1
bk
S2 S1
br
bk
bk
br
bk
br
br
bk
v
b
b
r
b
r
br
br
2
br
2
S
S
4
4
H
H
br
bk/w
bk
b
r
2
br
S
H
1.1kW
1.1kW
br
br
r
r
br
4
4a
b
v
br
2
2
S
S
H
C2
B2
br
br
2.02kW
4
H
r
w
4
4a
b
v
A21.65kW
bk
F2
1.56kW
bk/w
D2
br
br
b
G
b
b
w
r
r
br
br
Br
6
V
br
r
K
5
6
J2
br
P6
P5
5
P
P
b
v
L/1
y
N/2
y
r
br
bk
br
31
32
11
b
v
bk
w
b
P1
JI
12
b
P
b
w
w
bk
bk
H1
b
r
w
2
4
2
1 M1
w
b
r
P
b
b
gr
o
4a P2
v
8
P8
v
r
b
Q
M2
r
S2 S1
r
P7
P6
7
6
br
r
r
w
r
br
br
J4
J5
br
4
3
2
1
P4
gr
w
gr
P5
5
H3
P3
P2
P1
P4
P3
w
y
4
3
J3
J6
b
v
b
Q
V
w
w
bk
b
br
J7
o
b
R
o
y
2
1
br
o
P2
P1
J8
M3
br
b
bk
w
br
o
T
U
b
4
3
2
1
P4
P3
P2
P1
b
Q
M4
b
bk
br
br
V
b
b
r
br
w
br
b
b
b
b
br
b
y
b
H2
b
b
b
b
b
TOP
P1
TOP
P1
br
br br
b
b
br br br
b
b
b
b
b
b
br
5
6
2
2
2
4
6
1
3
5
4
4
P2
P2
4a
PILOT
S2
S1
S1
S2
L
L
L
N
N
N
2
1
K
A1, B1, C1
D1, F1,H1
35
Download from Www.Somanuals.com. All Manuals Search And Download.
121206
Download from Www.Somanuals.com. All Manuals Search And Download.
|