63-1089
indoor/outdoor thermometer
and hygro sensor
in your sensor
battery notes
ꢀRemove the battery compartment cover.
ꢁInsert two AAA batteries, matching the polarity symbols (+ and -),
marked inside.
ꢂSelect CHANNEL 1, 2, or 3 inside the compartment.
ꢃPress RESET to initialize the transmission.
•
For the best results, install batteries in
the remote sensor first, and then the
thermometer. Press RESET after each
battery replacement.
Thank you for purchasing your Indoor/Outdoor
Thermometer and Hygro Sensor from
RadioShack. You can mount it on a wall or
place it on a flat surface using the included
stand. Your thermometer displays indoor and
outdoor temperatures, as well as humidity
information. And, your thermometer even
features an atomic alarm clock.
•
•
) displays when battery power is low.
Dispose of old batteries promptly and
properly. Do not burn or bury batteries.
ꢄReplace the cover and secure it with the screws.
in the thermometer
ꢀRemove the battery cover.
ꢁInsert two AA batteries, matching the polarity symbols
•
•
Do not use rechargeable batteries.
Use only fresh batteries of the required size
and recommended type.
(+and -) marked inside.
ꢂReplace the battery cover.
•
•
Do not use batteries of different types
capacities, or chemistries.
If you do not plan to use this product for a
month, remove the batteries. Batteries can
leak chemicals that can damage electronic
parts.
Replace the batteries when the low battery icon appears. Press RESET
when you replace the batteries, or if it does not perform normally. All
settings will return to the default values and you will lose all stored
information.
RESET
C°/F° Switch
Press RESET on the sensor to receive a signal. Then, press and hold MEMORY and
CHANNEL on your thermometer to search for the sensor.
º - - º blinks on your thermometer while it is searching. To clear readings in
memory, press and hold MEMORY for 2 seconds. A beep sounds to confirm the
memory is clear.
You can place your thermometer and sensor
on a flat surface, using the included stand or
you can mount them on a wall. Insert your wire
stand into the holes on the back of your sensor
and place it in a desired location.
If you have more than one sensor, select a different channel for each one. Three
signal icons display when at least one channel has been found.
mounting your thermometer
ꢀ Drill a hole in the wall.
Keyhole Slot
selecting sensor channels
To auto-scan between sensors, press and hold CHANNEL for 2 seconds. Each
sensor’s data will be displayed for 3 seconds. To end auto-scan, press CHANNEL or
MEMORY. To select a specific channel, press Channel. The following icons display
based on the selected channel.
ꢁ Thread a screw (not supplied) into the hole,
letting it extend about 3/16” from the wall. Be
sure to use a screw with a head that fits into the
keyhole slot.
ꢂ Slide the thermometer down until it is secure.
Kinetic Wave Icon
Note: Actual product may vary from the images found in this
document.
mounting your sensor
ꢀ Drill a hole in the wall.
Designated
Display
Remote Display Remote Display Remote Display
Indoor Display
Channel 1
Channel 2
Channel 3
Keyhole Slot
ꢁ Thread a screw (not supplied) into the hole, letting
it extend about 3/16” from the wall. Be sure to use a
screw with a head that fits into the keyhole slot.
ꢀ- Press to increase settings and activate
the Atomic Clock signal reception.
Trend line - Indicates the trend of
temperature and humidity.
ꢂ Slide the sensor down until it is secure.
CHANNEL
Falling
Rising
Steady
ꢁ - Press to decrease
the setting.
thermometer and stand • thermo-sensor
user’s guide
Be sure to insert the batteries before you mount your
sensor.
Current Temperature
MODE - Press to change
display/settings.
Humidity Reading
3 - Press to view/change
alarm settings.
MEMORY - Press to view
CHANNEL - Press to switch
to a different sensor.
current or saved maximum
and minimum temperature or
humidity readings.
Please read this user’s guide before
installing, setting up and using your new product.
Download from Www.Somanuals.com. All Manuals Search And Download.
|