Cat 20-527
PRO-97 1,000 Channel Triple
Trunking Hand Held Scanner
Please read this user’s guide before installing,
setting up and using your new product
Download from Www.Somanuals.com. All Manuals Search And Download.
The Basics
contents
your scanner’s controls
7
power sources
12
12
14
15
16
16
17
17
17
18
using batteries
charging rechargeable batteries
using AC power
using vehicle battery power
connecting an earphone/headphones
listening safely
traffic safety
connecting an extension speaker
connecting the supplied antenna
connecting an optional external antenna
using the belt clip
18
19
19
transferring data to or from another scanner or PC
quick start
20
20
20
21
21
21
22
24
25
26
understanding your scanner’s modes
AM mode
FM mode
CTCSS (CT) mode
DCS (DC) mode
Motorola mode
EDACS mode
LTR mode
open and closed modes
setting up your scanner
turning on the scanner and setting squelch
storing known frequencies into channels
28
28
29
CTCSS and DCS
storing trunking frequencies into channels
31
33
3
Download from Www.Somanuals.com. All Manuals Search And Download.
The Basics
storing text tags
34
34
35
35
36
assigning a text tag to a channel
assigning a text tag to a group ID
assigning a tex tage to a bank
text input chart
finding and storing active frequencies
searching a preprogrammed frequency range
band charts
37
37
38
38
40
40
41
42
43
43
43
45
45
46
46
47
48
48
48
search bank: SR0 marine band
search bank: SR1 CB band
search bank: SR2 FRS/GMRS/MURS band
search bank: SR3 police/fire band
search bank: SR4 aircraft
search bank: SR5 amateur band
search bank: SR6 programmable limit search
searching active frequencies in a range
manually tuning a frequency
listening to the weather band
listening to a weather channel
SAME standby mode
WX Alert and beep tone confirmation
Skywarn
using frequency copy
copying a frequency into a specified channel
copying a frequency into an empty channel
within a bank
49
50
50
51
51
52
52
53
copying a frequency into the priority channel
Signal Stalker II
using Signal Stalker II
using Signal Stalker II with lockout
scanning channels
turning channel-starage banks off and on
monitoring a single channel/power save circuit
4
Download from Www.Somanuals.com. All Manuals Search And Download.
The Basics
using CTCSS and DCS
53
54
54
55
55
55
56
56
56
57
deleting frequencies from channels
deleting all frequencies in a channel bank
using dealy
locking out channels or frequencies
locking out channels
reviewing locked-out channels
locking out frequencies
reviewing locked-out frequencies
clearing a locked-out frequency
clearing all locked-out frequencies in a search bank 57
priority
changing the receive mode
using the attenuator
turning the key tone on and off
using the display/key backlight
using the keylock
changing the display contrast
cloning the programmed data
57
59
60
61
61
63
63
64
trunking
65
65
67
67
how trunking works
setting squelch for trunking mode
programming trunking frequencies
programming Motorola trunking systems (UHF-Lo) 69
programming Motorola trunking systems (800 MHz) 71
programming fleet maps
talk group IDs
storing talk group IDs
71
73
73
76
76
77
77
78
talk group ID hold
turning an ID sub-bank on or off
locking out talk group IDs
delay function in ID indication mode
reviewing locked-out talk group IDs
5
Download from Www.Somanuals.com. All Manuals Search And Download.
The Basics
clearing talk group IDs
clearing all talk group IDs in a single bank
changing the open/closed mode
78
78
79
care
service and repair
birdie frquencies
80
80
80
specifications
initializing your scanner
81
84
The FCC wants you to know
scanning legally
85
85
glossary
86
87
88
FAQs (Frequently Asked Questions)
warranty
Hypersearch, Hyperscan, and Adaptaplug are trademarks used by RadioShack Corporation.
Motorola, Smartnet, ASTRO and Privacy Plus are registered trademarks of Motorla Inc.
EDACS is a registered trademark of MA-COM Inc.
LTR is a registered trademark of EF Johnson.
6
Download from Www.Somanuals.com. All Manuals Search And Download.
The Basics
your scanner’s controls
SCAN/ — scans through the
programmed channels, or
activates the Signal Stalker II
function.
FUNC (function) — lets you
use various functions
by pressing this key in
combination with other keys.
MAN — stops scanning and
lets you directly enter a
channel number.
TRUNK — stores the trunking
ID code or holds the trunking
ID while scanning.
WX/
— scans through
the seven preprogrammed
weather channels, or jumps
to a Skywarn channel you
programmed (997-999).
PRI (Priority) — sets and turns
the priority function on or off.
TEXT — lets you input text.
PSE — stops search.
/
— turns on/off the
backlight, or when used
with FUNC locks/unlocks the
keypad to prevent accidental
entries.
MODE — changes the receive
mode (AM, FM, CT, DC, MO,
ED, LT).
7
Download from Www.Somanuals.com. All Manuals Search And Download.
The Basics
TUNE — lets you input a
frequency and allows you to
fine tune a frequency along
with e or d.
ATT (Attenuate) — turns
attenuation on to reduce
the scanner’s sensitivity
and block extremely strong
signals, or turns it off to
return the sensitivity to
normal.
e or d — selects the scan or
search direction.
SRCH — lets you search the
seven search banks.
L/OUT (Lock Out) — lets you
lock out a selected channel,
skip a specified frequency
during search, or lock out a
selected ID code.
PGM (Program) — programs
frequencies into channels.
ENT — completes the entry of
frequencies and text.
8
Download from Www.Somanuals.com. All Manuals Search And Download.
The Basics
1 — enters a 1, or inputs
characters 0 through 9 in text
mode.
2/ABC — enters a 2, or inputs
characters A, B, or C.
3/DEF — enters a 3, or inputs
characters D, E, or F.
4/GHI — enters a 4, or inputs
characters G, H, or I.
5/JKL — enters a 5, or inputs
characters J, K, or L.
6/MNO — enters a 6, or inputs
characters M, N, or O.
7/PQRS — enters a 7, or inputs
characters P, Q, R, or S.
8/TUV — enters an 8, or inputs
characters T, U, or V.
9/WXYZ — enters a 9, or inputs
characters W, X, Y, or Z.
./DELAY — enters a decimal
point (necessary when
programming frequencies),
space, or programs delay
time for the selected
0 — enters a zero, or inputs
characters ., -, #, _, @, +, *,
&, /, ,, $, %, !, ^, (, ), ?, ~, ‘,
or ∆.
channel/search bank, or
enters a hyphen (in trunking
ID setting).
CL (Clear) — clears an
incorrect entry.
9
Download from Www.Somanuals.com. All Manuals Search And Download.
The Basics
PWR DC 9V — connect a power
source here.
PC/IF — connect an optional
PC interface cable here to
use the scanner with your
computer.
10
Download from Www.Somanuals.com. All Manuals Search And Download.
The Basics
ANT — connect the supplied
antenna or an external
antenna here.
— connect an earphone
or headphone here.
OFF VOL/SQ — turn the scanner
on or off and adjust the
squelch.
11
Download from Www.Somanuals.com. All Manuals Search And Download.
The Basics
power sources
You can power your scanner from any of these sources:
• internal non-rechargeable batteries or rechargeable
batteries (not supplied – see “Using Batteries”).
• standard AC power (with an optional AC adapter – see
“Using AC Power”).
• vehicle power (with an optional DC adapter – see “Using
Vehicle Battery Power”).
Connecting an AC or DC adapter to the scanner
disconnects internal batteries when you use the
supplied non-rechargeable battery holder, but it does not
disconnect internal batteries when you use the supplied
rechargeable battery holder.
Notes
If you install the rechargeable battery holder, you can
operate the scanner and recharge the rechargeable
batteries at the same time. See “Using Batteries” and
“Charging Rechargeable Batteries”.
If the scanner stops working properly after connecting it
to power, try resetting it. See “Initializing the Scanner”.
You must charge rechargeable batteries before you
use them the first time. See “Charging Rechargeable
Batteries”.
using batteries
You can power the scanner with four AA batteries (not
supplied). For the longest operation and best performance,
we recommend alkaline batteries, available at your local
RadioShack store.
You can use either the supplied non-rechargeable battery
holder (black), or the supplied rechargeable battery holder
(yellow). If you use the rechargeable battery holder, we
12
Download from Www.Somanuals.com. All Manuals Search And Download.
The Basics
recommend RadioShack nickel-metal hydride (Ni-MH)
batteries.
You must charge rechargeable batteries before you use them
the first time. See “Charging Rechargeable Batteries”.
Never install non-rechargeable batteries in the
rechargeable yellow battery holder. Non-Rechargeable
batteries can get hot or explode if you try to recharge
them.
Warning!
The battery holder fits only one way. Do not force it.
Notes
Use only fresh batteries of the required size and
recommended type.
Always remove old or weak batteries. Batteries can leak
chemicals that destroy electronic circuits.
Do not mix old and new batteries, different types of
batteries (alkaline or rechargeable), or rechargeable
batteries of different capacities.
If you do not plan to use the scanner with batteries for a
month or longer, remove the batteries. Batteries can leak
chemicals that can destroy electronic parts.
Follow these steps to install the batteries.
1. Press in on the battery compartment cover on the back of
the scanner and slide the cover down to remove it.
2. Pull the battery holder out of the battery compartment.
3. If you are using non-rechargeable batteries, place them
into the black holder, as indicated by the polarity symbols
(+ and -) marked on the holder.
If you are using rechargeable batteries, place them into the
yellow holder as indicated by the polarity symbols (+ and -)
marked on the holder.
4. Place the battery holder into the battery compartment.
13
Download from Www.Somanuals.com. All Manuals Search And Download.
The Basics
5. Replace the cover.
When battery power is low, Low battery! appears and
the scanner beeps continuously. When battery power
is depleted, the scanner turns itself off. Replace all four
non-rechargeable batteries, or recharge the rechargeable
batteries. See “Charging Rechargeable Batteries”.
Always dispose of old batteries promptly and properly.
Do not bury or burn them.
Notes
If you do not plan to use the scanner with batteries for a
month or longer, remove the batteries. Batteries can leak
chemicals that can destroy electronic parts.
charging rechargeable batteries
Your scanner has a built-in charging circuit that lets you
charge nickel-metal hydride (Ni-MH) or nickel cadmium (Ni-
CD) rechargeable batteries (not supplied) while they are in
the scanner. To charge rechargeable batteries, connect an
appropriate AC or DC adapter to the PWR DC 9V jack. For
best results we recommend RadioShack rechargeable nickel-
metal hydride (Ni-MH) 1600 mAh batteries.
The EPA certified RBRC© Battery Recycling Seal on the
nickel-cadmium (Ni-Cd) battery indicates RadioShack
is voluntarily participating in an industry program to
collect and recycle these batteries at the end of their
useful life, when taken out of service in the United States
or Canada. The RBRC program provides a convenient
alternative to placing used Ni-Cd batteries into the trash
or the municipal waste stream, which may be illegal in
your area. Please call 1-800-THE-SHACK (1-800-843-7422)
for information on Ni-Cd battery recycling and disposal
bans/restrictions in your area. RadioShack’s involvement
in this program is part of the company’s commitment to
preserving our environment and conserving our natural
resources.
Notes
14
Download from Www.Somanuals.com. All Manuals Search And Download.
The Basics
It takes about 16 hours to recharge fully discharged 1600
mAh Ni-MH rechargeable batteries. You can operate the
scanner while recharging the rechargeable batteries, but
charging takes longer.
The scanner can also charge Ni-Cd batteries. 600 mAh
Notes
batteries require 6 hours and 850 mAh batteries require 8
hours to charge.
When you charge rechargeable batteries, do not
overcharge them. Overcharging shortens battery life.
Rechargeable batteries last longer and deliver more
power if you let them fully discharge once a month. To
do this, use the scanner until Low battery! appears. Then
fully charge the rechargeable batteries.
using AC power
You can power the scanner using a 9V, 300 mA AC adapter
and a size C Adaptaplug (neither supplied). Both are available
at your local RadioShack store.
1. Connect the Adaptaplug to the adapter’s cord with the tip
set to positive.
You must use a Class 2 power source that supplies 9V
Notes
DC and delivers at least 300 mA. Its center tip must be
set to positive and its plug must fit the scanner’s PWR
DC 9V jack. Using an adapter that does not meet these
specifications could damage the scanner or the adapter.
2. Plug the adapter’s barrel plug into the scanner’s PWR DC
9V jack.
3. Plug the adapter’s two-prong plug into an AC outlet.
15
Download from Www.Somanuals.com. All Manuals Search And Download.
The Basics
using vehicle battery power
You can power the scanner from a vehicle’s 12V power
source (such as cigarette-lighter socket) using a 9V, 300
mA DC adapter and a size C Adaptaplug™ adapter (neither
supplied). Both are available at your local RadioShack store.
You must use a power source that supplies 9V DC and
Notes
delivers at least 300 mA. Its center tip must be set to
positive and its plug must fit the scanner’s PWR DC
9V jack. Using an adapter that does not meet these
specifications could damage the scanner or the adapter.
1. Connect the Adaptaplug to the adapter’s cord with the tip
set to positive.
2. Plug the adapter’s barrel plug into the scanner’s PWR DC
9V jack.
3. Plug the adapter’s cigarette-lighter plug into your 12V
power source.
f the scanner does not operate properly when you
connect a DC adapter, unplug the DC adapter from the
power source and clean the socket, or check the adapter’s
internal fuse.
Notes
connecting an earphone/headphones
For private listening, you can plug an 1/8-inch (3.5 mm)
mini-plug earphone or headphones (not supplied), available
at your local RadioShack store, in the jack on top of your
scanner. This automatically disconnects the internal speaker.
16
Download from Www.Somanuals.com. All Manuals Search And Download.
The Basics
listening safely
To protect your hearing, follow these guidelines when you
use an earphone or headphones.
•
Set the volume to zero before putting on headphones.
With the headphones on, adjust the volume to a
comfortable level.
•
Avoid increasing the volume once you set it. Over time,
your sensitivity to a volume level decreases, so volume
levels that do not cause discomfort might damage your
hearing.
•
Avoid or limit listening at high volume levels. Prolonged
exposure to high volume levels can cause permanent
hearing loss.
traffic safety
Do not wear an earphone or headphones while you drive a
vehicle or ride a bicycle. This can create a traffic hazard and
can be illegal in some areas. Even though some earphones
and headphones let you hear some outside sounds when you
listen at normal levels, they still can present a traffic hazard.
connecting an extension speaker
In a noisy area, an amplified speaker (not supplied), available
at your local RadioShack store, might provide more
comfortable listening. Plug the speaker cable’s 1/8-inch (3.5
mm) mini-plug into your scanner’s jack.
17
Download from Www.Somanuals.com. All Manuals Search And Download.
The Basics
connecting the supplied
antenna
To attach the supplied flexible antenna
to the antenna jack on the top of your
scanner, align the slots around the
antenna’s connector with the tabs on the
antenna jack. Press the antenna down
over the jack and turn the antenna’s
base clockwise until it locks into place.
connecting an optional external
antenna
The antenna connector on your scanner
makes it easy to use the scanner with a
variety of antennas, such as an external
mobile antenna or outdoor base station
antenna. Your local RadioShack store sells a variety of
antennas.
Always use 50-ohm coaxial cable, such as RG-58 or RG-8, to
connect an outdoor antenna. For lengths over 50 feet, use
RG-8 low-loss dielectric coaxial cable. If your antenna’s cable
does not have a BNC connector, you will also need a BNC
adapter (not supplied, available at your local RadioShack
store).
Follow the installation instructions supplied with the antenna,
route the antenna cable to the scanner, then connect it to the
antenna jack.
Use extreme caution when installing or removing an
utdoor antenna. If the antenna starts to fall, let it go!
t could contact overhead power lines. If the antenna
touches a power line, touching the antenna, mast, cable,
or guy wires can cause electrocution and death. Call the
power company to remove the antenna. DO NOT attempt
to do so yourself.
Warning!
18
Download from Www.Somanuals.com. All Manuals Search And Download.
The Basics
using the belt clip
To make your scanner easier to
carry when you are on the go, use
the supplied belt clip by attaching
it to the back of the scanner. To
remove the battery clip, slide
it upward while pulling the tab
toward you.
transferring data to or
from another scanner or
PC
You can transfer the programmed data to and from another
PRO-97 scanner using a connecting cable which has 1/8
-inch phone plugs on both ends (not supplied). Connect
the cable between each scanner’s PC/IF jacks. See “Cloning
the Programmed Data”. You can also upload or download
the programmed data to or from a PC using an optional PC
interface kit available through your local RadioShack store.
19
Download from Www.Somanuals.com. All Manuals Search And Download.
The Basics
quick start
To help familiarize yourself with the scanner’s functions,
keypad, and available frequencies, you can utilize one of
these four features before you begin programming the
scanner.
Signal Stalker II — searches nearby strong signals quickly.
See “Signal Stalker II”.
Preprogrammed Search Banks — allow you to listen to
frequencies and decide which frequencies you want to store
when you are ready to program the scanner. See “Searching
a Preprogrammed Frequency Range”.
Manual Tuning — allows you to manually move through the
entire range of available frequencies. (See “Specifications”
for a list of the available frequency ranges.)
Weather Radio — allows you to listen to NOAA weather
broadcasts without programming. See “Listening to the
Weather Band”.
understanding your scanner’s modes
You can program each channel with any of seven receive
modes (AM, FM, CT, DC, MO, ED, and LT).
Each receive mode affects how your scanner operates when
scanning and receiving transmissions.
Trunked modes (MO, ED and LT) can only be selected for
Notes
requencies above 137 MHz.
Your scanner’s closed mode lets you hear only those
trunking talkgroups you specify. For more information,
see “Open and Closed Modes”.
AM mode
The AM mode sets the scanner to receive transmissions
using amplitude modulation (AM), primarily used for aircraft,
20
Download from Www.Somanuals.com. All Manuals Search And Download.
The Basics
military, some amateur radio, and some government
transmissions. (Refer to “Specifications” for a list of
the frequencies covered.) When the scanner receives a
transmission on a channel set to the AM mode, it always
stops on the transmission.
FM mode
The FM mode sets the scanner to receive transmissions
using frequency modulation (FM), used for most public
safety transmissions, as well as broadcast, business, and
amateur radio transmissions. When the scanner receives
a transmission on a channel set to the FM mode, it always
stops on the transmission.
CTCSS (CT) mode
CTCSS mode sets the scanner to receive transmissions
using frequency modulation (FM) with Continuous Tone
Coded Squelch System (CTCSS) subaudible tone codes.
CTCSS allows multiple users to share a single radio
frequency without hearing each other’s transmissions. In
your PRO-97 scanner, the CTCSS feature can be used to
block the reception of transmissions on shared channel to
only those that use the CTCSS mode also features a Code
Search setting that allows you to instantly display and store
unknown codes into the channel memory. CTCSS tones can
sometimes be heard as a low “hum” in the background of a
voice transmission.
DCS (DC) mode
DCS mode sets the scanner to receive transmissions using
frequency modulation (FM) with Digital Coded Squelch
(DCS) subaudible data signaling. DCS is very similar to
CTCSS, except that a digital code is transmitted instead of
an audio tone. Like CTCSS, DCS allows multiple users to
share a single radio frequency without hearing each other’s
21
Download from Www.Somanuals.com. All Manuals Search And Download.
The Basics
transmissions. In your PRO-97 scanner, the DCS feature can
be used to block the reception of transmissions on a shared
channel to only those that use the DCS tone that you have
specified. DCS mode also features a Code Search setting
that allows you to instantly display and store unknown
codes into the channel memory. DCS data can sometimes
be heard as a low “purring” sound in the background of a
voice transmission. Some DCS systems transmit a special
“turn off code” at the end of each transmission. The turn off
code causes a properly equipped receiver to mute before
the transmission ends, eliminating the “squelch tail” burst of
noise the commonly occurs when the signal is lost.
Motorola mode
You can set your scanner so it decodes the talk group IDs
used with Motorola trunking systems. This setting is called
the Motorola mode.
Motorola systems are trunking systems used primarily by
business and public safety groups to efficiently allocate a
small number of frequencies (as few as five) to many groups
of users (as many as several thousand). To do this, each
group of users in the system is assigned to a specific talk
group. For example, the east side patrol officers might all
be assigned to talk group 2160. One channel in the system
is continuously transmitting data that identifies which talk
groups are active on which channel. In addition, this talk
group information is also transmitted as subaudible data on
each active channel.
When the scanner receives a transmission on a channel
set to the Motorola mode, it first decodes the talk group
ID data included with the transmission. In the open mode,
the scanner stops on the transmission and displays the talk
group ID on the bottom line of the display. In the closed
mode, the scanner only stops on the transmission if the talk
group ID matches a talk group ID that you have stored in the
22
Download from Www.Somanuals.com. All Manuals Search And Download.
The Basics
bank’s talk group ID list and have not locked out.
Motorola trunking systems come in three categories: Type I,
Type II, and Type I/II Hybrid. Each category displays and uses
talk group IDs in slightly different ways.
Motorola Type II IDs are in the form FFF-SS, where;
FFF=Fleet ID
SS=Subfleet ID
Type I systems are usually organized with different user
groups assigned to different fleets.
For example, a valid fleet-subfleet ID identifying all
detectives within a police department might be 000-12,
where 000 identifies all police users and 12 identifies the
Detective division.
Notes
Tuning the scanner to an active control channel while
in Motorola mode will display the Motorola System. ID
and the approximate control channel message decode
success rate. This information can help you identify the
Motorola trunking system that you are monitoring and
the receive quality of the control channel signal.
To properly map the raw Type I data to the correct fleet-
subfleet format, you must program the correct fleet map into
the scanner. Fleet map information is widely available on the
Internet for most Type I systems in use.
Type II system talk groups are identified by a 5-digit number.
Valid talk group IDs are divisible by 16. If you try to enter an
invalid talk group ID, the scanner rounds the ID down to the
next valid ID.
Type I/II hybrid systems use both fleet-subfleet and 5-digit
formats for talk group IDs.
f the scanner decodes control channel data while
receiving transmissions from a Motorola trunking
system, CNTRL appears on the bottom line of the display.
Notes
23
Download from Www.Somanuals.com. All Manuals Search And Download.
The Basics
EDACS mode
You can set your scanner so it decodes the talk group IDs
used with EDACS (GE/Ericsson) trunking systems. This
setting is called the EDACS mode.
EDACS systems are trunking systems used primarily by
business or private communications service providers, as
well as by some public safety organizations. EDACS systems
transmit active talk group information only on a dedicated
control channel.
EDACS frequencies are organized in a specific order. Each
frequency is assigned a Logical Channel Number (LCN). For
the scanner to correctly switch to an active frequency, you
must program the frequencies in LCN order, starting with
Memory 01. EDACS talk group IDs are entered as a 4-digit
decimal number from 0001 to 2047 or AFS (Agency Fleet
Subfleet) number from 00-001 to 15-157.
When there is activity on an EDACS system, that information
is sent out on the control channel. The scanner decodes the
ID for the active talk group. In the open mode, the scanner
then goes to the transmission and displays the talk group
ID on the bottom line of the display. In the closed mode, the
scanner only goes to transmissions with IDs that match talk
group IDs you have stored in the bank’s talk group ID list
which are not locked out.
Because EDACS scanning requires clear reception of the
control channel at all times, EDACS systems tend to have a
smaller usable area. An external antenna can greatly improve
EDACS scanning in a fringe area. If you are having trouble
scanning an EDACS system, try manually selecting the data
channel. If you are getting good reception, the scanner will
indicate talk group CTL-01. Try changing your location or
using an outdoor antenna to improve reception.
24
Download from Www.Somanuals.com. All Manuals Search And Download.
The Basics
LTR mode
You can set your scanner so it decodes the talk group IDs
used with LTR systems. This setting is called the LTR mode.
LTR frequencies are organized in a specific order. Each
frequency is assigned a Home Repeater Number (HR). For
the scanner to correctly switch to an active frequency, you
must program the frequencies in HR order, starting with
Memory X01 in the selected bank.
Your PRO-97 scanner features a new tool to help you
determine the correct channel mapping for LTR system
frequencies. The scanner’s LTR Repeater Finder displays the
current Home Repeater when monitoring LTR transmissions
in manual mode.
To determine the correct Home Repeater programming,
enter the system channels of an LTR system in any order. Be
sure to program the mode for each LTR channel to LT. Listen
to each channel one at a time in manual mode and watch for
the decoded LTR data at the bottom of the scanner’s display.
When an LTR transmission occurs, you should see the LTR
talkgroup information on the bottom line of the display, and
a number preceded by “R” in the bottom right hand corner
(i.e., R12). The “R” number is the Home Repeater number
that the current transmission is occurring on. To correctly
program this Home Repeater number into your scanner,
be sure that the channel number in the bank is equal to
the number that is displayed after the “R”. For example, if
you see R12 displayed on a particular LTR frequency, that
frequency needs to be programmed into Channel 12 of
the current bank in order to track the LTR system activity
properly.
LTR systems are trunking systems used primarily by
business or private communications service providers,
such as taxicabs, delivery trucks, and repair services. These
systems encode all trunking information as digital subaudible
data that accompanies each transmission. Users on an
25
Download from Www.Somanuals.com. All Manuals Search And Download.
The Basics
LTR system are assigned to specific talk groups, which are
identified by the radio as six-digit numbers. These numbers
are in the form AHHUUU, where:
A = Area code (0 or 1)
H = Home repeater (01 through 20)
U = User ID (000 through 254)
When the scanner receives a transmission on a channel set
to the LTR mode, it first decodes the LTR data included with
the transmission. In the open mode, the scanner stops on the
transmission and displays the talk group ID on the bottom line
of the display. In the closed mode, the scanner only stops on
the transmission if the LTR data matches a talk group ID that
you have stored in the bank’s talk group ID list and have not
locked out.
LTR systems are frequently programmed so that each radio
has a unique ID code.
open and closed modes
You can set your scanner to change the way it receives
signals. These settings, called open mode and closed mode,
affect how the scanner receives signals from communications
systems that use some type of closed squelch (such as
Motorola, EDACS, and LTR systems).
n open mode, you hear all active talk groups except those
you specifically exclude, making it easy to hear everything
going on. In closed mode, you hear only those talk groups
you specify. This makes it easy to listen only to talk groups
you are interested in and exclude others.
Notes
When you select a system voice channel manually, any
transmission opens squelch, regardless of the current
mode.
26
Download from Www.Somanuals.com. All Manuals Search And Download.
The Basics
When no ID code is programmed into the scanner, it
receives the signal in MO, ED, or LT mode. In open mode,
the scanner stops on any transmission. If the ID is stored,
the text tag appears on the display. Otherwise, the talk
group ID appears on the display. In closed mode, the
scanner only stops on a transmission if the ID is stored.
You can set each of the scanner’s channel storage banks to
open or closed mode.
In open mode, the scanner scans signals transmitted in all
systems. The scanner stops on any ID code and only uses
the ID list to look up ID text tags.
In closed mode, the scanner stops only on signals that have
an ID code which is found in the ID list for the bank. Also, the
scanner scans signals transmitted only under the following
conditions:
• When the signals are in the FM, CT, or DC mode.
• When the signals are in the MO, ED, or LT mode and the
signal’s ID code matches the programmed ID code
You can also select the user or talk groups you want the
scanner to receive in closed mode.
When you set a channel storage bank to open mode, +
appears under the bank’s number while scanning. When you
set a channel storage bank to closed mode, - appears under
the channel storage bank’s number while scanning. OPEN
or CLOSED appears while the scanner is in manual mode or
while the scanner is receiving a signal during scanning. See
“Changing the Open/Closed Mode” for more information
about setting the open and closed modes.
27
Download from Www.Somanuals.com. All Manuals Search And Download.
The Basics
setting up your scanner
turning on the scanner and setting squelch
1. To turn on the scanner, turn VOL clockwise. Multi-system
Trunking Scanner appears. After about 3 seconds,
you might hear a hissing sound. Then adjust VOL to a
comfortable level.
2. Turn SQ fully counterclockwise, then turn SQ clockwise until
the hissing sound stops.
3. To turn off the scanner, turn VOL counterclockwise to OFF.
The scanner does not scan if there are no frequencies
stored in channels. If the scanner does not scan and
you have already stored frequencies in channels, turn SQ
further clockwise.
Notes
If the scanner picks up unwanted, partial, or very
weak transmissions, turn SQ clockwise to decrease the
scanner’s sensitivity to these signals. If you want to listen
to a weak or distant station, turn SQ counterclockwise.
If SQ is adjusted so you always hear a hissing sound, the
scanner will not scan properly.
To ensure the scanner operates properly while in the
trunking mode, we suggest you set SQ using the steps
listed above.
If SQ is adjusted precisely at the threshold where the
hissing sound stops, the radio will be most sensitive to
very weak signals. The radio may also receive unwanted
noise or signals that are too weak to understand. Most
users prefer to position the squelch control a little bit past
the point of threshold to avoid receiving noise or signals
that are too weak to understand.
28
Download from Www.Somanuals.com. All Manuals Search And Download.
The Basics
storing known frequencies into channels
Good references for active frequencies are RadioShack’s
Police Call, Aeronautical Frequency Directory, and Maritime
Frequency Directory. We update these directories every year,
so be sure to get a current copy.
Follow these steps to store frequencies into channels.
you are storing frequencies for an EDACS system,
Notes
ou must store them in order, with the first frequency in
channel 1 for the current bank. For example, if you want
to store frequency of 150.0100, 150.0200, 150.0300, and
150.0400 MHz, you must store them in Channels 1, 2, 3,
and 4 respectively.
When M appears on the display, you can use FUNC and
the arrow keys to select your desired bank and channel
number.
1. Press MAN, enter the bank (0-9) and channel number (00-
99) where you want to store a frequency, then press MAN
again. M and the bank and channel number appear at the
upper left corner of the display (for example: M000).
Press FUNC. Then press e or d. The bank number moves in
Notes
he direction of the arrow pressed.
Press FUNC. Then hold down e or d. The bank number
moves continuously in the assigned direction.
Press e. The channel number moves upward one by one.
Or, press d. The channel number moves downward one
by one.
29
Download from Www.Somanuals.com. All Manuals Search And Download.
Beyond the Basics
2. Press PGM. M changes to P.
3. Use the number keys and ./DELAY to enter the frequency
(including the decimal point) you want to store.
If you make a mistake, press CL to delete a single digit or press
and hold CL about 2 seconds to delete all digits.
4. Press ENT to store the frequency into the channel.
f you made a mistake in Step 3, Invalid Freq. briefly
Notes
appears and the scanner beeps when you press ENT. Start
again from Step 3.
Your scanner automatically rounds the entered frequency
to the nearest valid frequency. For example, if you enter a
frequency of 151.553, your scanner accepts it as 151.550.
All scanners tune by steps. Your RadioShack scanner
uses steps consistent with the latest US or worldwide
standards. If you enter a non-valid step frequency, any
scanner will tune to the next step. Some scanner designs
do this without showing the correct step in the display.
This scanner will show the actual tuned frequency in the
display. Because steps are so close together, the audio
quality will not be affected by the offset.
After a transmission, the scanner automatically pauses
for 2 seconds on this channel before proceeding to the
next active transmission. Press ./DELAY to turn the delay
function off or on. See “Using Delay”. The scanner stores
this setting in the channel.
5. If necessary, press MODE to change the receiving mode.
6. If desired, program a text tag for the channel (see
“Assigning a Text Tag to a Channel”).
7. The next channel in sequence is ready for programming.
Press PGM then repeat steps 3 through 6.
30
Download from Www.Somanuals.com. All Manuals Search And Download.
Beyond the Basics
CTCSS and DCS
Your PRO-97 scanner features an advanced, DSP based
CTCSS and DCS decoder. CTCSS and DCS allow you to
program frequencies into your scanner that are used by more
than one group in your area and listen only to the group that
is of interest to you by specifying the group’s specific CTCSS
or DCS code. CTCSS and DCS can also help reduce instances
where interfering signals cause your scanner to stop on one
channel.
There are two ways you can program your scanner to
operate with CTCSS and DCS. If you know the CTCSS or DCS
code that is used on a particular frequency, you can manually
enter the code when you are programming the scanner, or
any time afterwards.
You can also set a special search code up that will instantly
decode the CTCSS or DCS code on a received transmission.
Channels programmed with the search code will receive all
traffic on the channel, and will instantly decode and display
any CTCSS or DCS code that is found with the transmission.
You can then store the found code in the channel memory
with one keystroke.
This section of the manual describes the process for
configuring a memory channel for CTCSS or DCS operation
and manually programming a known code. For more
information on using the CTCSS and DCS feature while
scanning, see “Using CTCSS and DCS”.
To program channel memories for CTCSS or DCS operation,
follow these steps:
1. First, enter a conventional frequency. See “Storing Known
Frequencies into Channels”.
2. Once you have entered the frequency, press MODE until the
desired mode appears in the upper left hand corner of the
display. Use CT for CTCSS, and DC for DCS.
31
Download from Www.Somanuals.com. All Manuals Search And Download.
Beyond the Basics
3. By default, the search code (indicated with Code Search in
the bottom of the display) is programmed. To program
a specific code, press FUNC, MODE, and then use the arrow
keys to scroll to the desired CTCSS or DCS code. You can
also use the keypad to enter the code manually. Note that
the scanner will automatically fill the code field as you
enter the code.
4. Once the desired code is selected, press ENT to store the
code in the channel memory.
5. It is possible to program memory channels for CTCSS
or DCS operation at any time. Simply place the scanner
in program mode, navigate to the channel you wish to
change, and follow the steps above.
6. When stopped on an active conventional channel while
scanning, you can press MODE to cycle through the valid
modes for that channel, including CTCSS and DCS. This
will reset any stored CT or DC code to the search code,
allowing you to easily check for other CT or DC codes
that may be present on the frequency.
CTCSS, DCS and digital voice all operate independently
Notes
of each other. If a channel is configured for CTCSS or
DCS, it will not be able to decode digital transmissions.
Use the FM mode when mixed analog and digital voice
reception is desired.
CTCSS Code Table:
67.0 Hz
69.3 Hz
71.9 Hz
74.4 Hz
77.0 Hz
79.7 Hz
94.8 Hz
131.8 Hz
136.5 Hz
141.3 Hz
146.2 Hz
151.4 Hz
156.7 Hz
171.3 Hz
173.8 Hz
177.3 Hz
179.9 Hz
183.5 Hz
186.2 Hz
203.5 Hz
206.5 Hz
210.7 Hz
218.1 Hz
225.7 Hz
229.1 Hz
97.4 Hz
100.0 Hz
103.5 Hz
107.2 Hz
110.9 Hz
32
Download from Www.Somanuals.com. All Manuals Search And Download.
Beyond the Basics
82.5 Hz
85.4 Hz
88.5 Hz
91.5 Hz
114.8 Hz
159.8 Hz
162.2 Hz
165.5 Hz
167.9 Hz
189.9 Hz
192.8 Hz
196.6 Hz
199.5 Hz
233.6 Hz
241.8 Hz
250.3 Hz
254.1 Hz
118.8 Hz
123.0 Hz
127.3 Hz
DCS Code Table:
006
007
015
017
021
023
025
026
031
032
036
043
047
050
051
053
054
065
071
072
073
074
114
115
116
122
125
131
132
134
141
143
145
152
155
156
162
165
172
174
205
212
214
223
225
226
243
244
245
246
251
252
255
261
263
265
266
271
274
306
311
315
325
331
332
343
346
351
356
364
365
371
411
412
413
423
431
432
445
446
452
454
455
462
464
465
466
503
506
516
523
526
703
712
723
731
732
734
743
754
532
546
565
606
612
624
627
631
632
654
662
664
storing trunking frequencies into channels
1. Press PGM and FUNC then e or d to select the desired bank
to program.
2. Press TRUNK to enter into trunking mode.
3. Repeatedly press MODE to select Motorola, EDACS, or LTR.
4. Press PGM and select the channel number using e or d.
5. Enter the UHF trunking frequency and press ENT.
33
Download from Www.Somanuals.com. All Manuals Search And Download.
Beyond the Basics
6. Repeat Steps 4 and 5 to enter the other trunking group
frequencies for EDACS or additional control channel
frequencies for Motorola systems.
7. If necessary, press MODE to change the receiving mode.
storing text tags
You can customize your scanner by storing text tags
(up to 16 characters) for easy identification of channel
transmissions, trunk IDs, or banks.
assigning a text tag to a channel
1. Press MAN, enter the channel number where you want to
enter the text, then press MAN again. M and the bank and
channel number appear at the upper left corner of the
display (for example: M100).
2. Press PGM. M changes to P.
3. Press TEXT. The cursor appears at the third line.
4. Enter the text using the numeral keys (see “Text Input
Chart”).
f you make a mistake, press e or d to move to the
Notes
character you want to change.
For example, to identify amateur (ham) radio
transmissions in the 6 meter range, input “HAM 6m” as
follows:
• “H” is the second letter associated with 4 on the
keypad. Press 4 then 2.
• “A” is the first letter associated with 2 on the keypad.
Press 2 then 1.
• “M” is the first letter associated with 6 on the keypad.
34
Download from Www.Somanuals.com. All Manuals Search And Download.
Beyond the Basics
Press 6 then 1.
• A space is entered by pressing ./DELAY.
• “6” is the sixth number associated with 1 on the
keypad. Press 1 then 6.
• “m” is the first letter associated with 6 on the keypad.
Press 6 and FUNC (for the lower case set), then press 1.
5. Press ENT to input the text.
assigning a text tag to a group ID
1. Press PGM.
2. Press TRUNK.
3. Press FUNC then e or d to select the desired bank.
4. Press TRUNK to select the desired sub-bank.
5. Press or hold down e or d to select the desired group ID.
6. Press TEXT then enter the tag using the keypad. (See “Text
Input Chart”).
7. Press ENT to store.
assigning a text tag to a bank
1. Press PGM.
2. Press FUNC then press bank number. Bank X (0 through
9) selected. Fn+CLR to delete all frequencies, TEXT to edit tag
appears.
3. Press TEXT, then enter the text using the keypad.
4. Press ENT to store.
35
Download from Www.Somanuals.com. All Manuals Search And Download.
Beyond the Basics
text input chart
To access the numbers, after you press TEXT (when you
Notes
assign the text tag to a channel) or you press FUNC and
bank number (when you assign the text tag to a bank),
press 1. Then press the desired number you want to enter.
To enter lowercase character or a character from the
second set for the key 0, press FUNC after pressing the first
numeral key.
PRESSED
CHARACTERS
0 1 2 3 4 5 6 7 8 9
A B C
1
2
2 then FUNC
a b c
3
D E F
3 then FUNC
d e f
4
G H I
4 then FUNC
g h I
5
J K L
5 then FUNC
j k l
6
M N O
6 then FUNC
m n o
7
P Q R S
p q r s
7 then FUNC
8
T U V
8 then FUNC
t u v
9
W X Y Z
w x y z
9 then FUNC
0
. - # _ @ + * & / ,
$ % ! ^ ( ) ? ~ ‘ ∆
Space
0 then FUNC
•/DELAY
CL
Back Space
36
Download from Www.Somanuals.com. All Manuals Search And Download.
Beyond the Basics
finding and storing active
frequencies
You can search for transmissions in the scanner’s
preprogrammed search bank. The search bank is divided
into seven search bands. You can change the search range of
Bank SR6 manually by setting the lower and higher ends of
the search range.
You can use the scanner’s delay feature while searching
he search bank. See “Using Delay”.
Notes
The scanner does not search locked-out frequencies
while searching ranges. See “Locking Out Channels or
Frequencies”.
searching a preprogrammed frequency range
The scanner contains these preprogrammed search ranges,
stored in the search bank (SR0-SR6).
Bank
SR0
SR1
SR2
SR3
SR4
SR5
SR6
Band
Marine
CB
FRS/GMRS/MURS
Police/Fire
Aircraft
Amateur Bands
Limit search (User
changeable)
Follow these steps to select preprogrammed search bands
and search them for active frequencies:
1. Repeatedly press SRCH to select your desired search bank
(SR0, SR1, SR2, SR3, SR4, SR5, or SR6).
37
Download from Www.Somanuals.com. All Manuals Search And Download.
Beyond the Basics
2. In the marine, CB, and FRS/GMRS/MURS bands, you
can directly select a channel or search through the band.
When MAN appears at the right of the third line, you can
directly select a channel (refer to “Band Charts”). Press
the desired channel number while MAN appears to select
it. You can also change the channels by pressing e or d.
3. Press FUNC then SRCH while MAN appears. MAN changes to
SRCH and now you can search through the band. Press
FUNC then SRCH again to return to the previous mode.
4. Rotate SQ clockwise and leave it set to a point just after
the rushing sound stops. After 2 seconds (if the delay
feature is on), the scanner starts searching.
5. When the scanner finds an active frequency, it stops
searching.
band charts
search bank: SR0 marine band
Two frequencies are assigned in one channel in some
Notes
Marine frequencies. For example, 157.000 and 161.600
are assigned in Channel 20.
Receive mode: FM
Ch.
Frequency
(MHz)
Ch.
Frequency
(MHz)
01
06
156.0500
156.3000
05
07
156.2500
156.3500
38
Download from Www.Somanuals.com. All Manuals Search And Download.
Beyond the Basics
08
10
12
14
16
18
20
156.4000
156.5000
156.6000
156.7000
156.8000
156.9000
09
11
13
15
17
19
21
156.4500
156.5500
156.6500
156.7500
156.8500
156.9500
157.0500
157.0000
161.6000
22
24
157.1000
23
25
157.1500
157.2000
161.8000
157.2500
161.8500
26
28
64
157.3000
161.9000
27
63
65
157.3500
161.9500
157.4000
162.0000
157.1750
156.2250
160.8250
156.2750
66
68
70
72
74
78
80
82
84
156.3250
156.4250
156.5250
156.6250
156.7250
156.9250
157.0250
157.1250
67
69
71
73
77
79
81
83
85
156.3750
156.4750
156.5750
156.6750
156.8750
156.9750
157.0750
157.1750
157.2250
161.8250
157.2750
161.8750
86
88
157.3250
161.9250
87
157.3750
161.9750
157.4250
39
Download from Www.Somanuals.com. All Manuals Search And Download.
Beyond the Basics
search bank: SR1 CB band
Receive mode: AM
Ch.
Frequency
(MHz)
Ch.
Frequency
(MHz)
01
03
05
07
09
11
13
15
17
19
21
23
25
27
29
31
33
35
37
39
26.9650
26.9850
27.0150
27.0350
27.0650
27.0850
27.1150
27.1350
27.1650
27.1850
27.2150
27.2550
27.2450
27.2750
27.2950
27.3150
27.3350
27.3550
27.3750
27.3950
02
04
06
08
10
12
14
16
18
20
22
24
26
28
30
32
34
36
38
40
26.9750
27.0050
27.0250
27.0550
27.0750
27.1050
27.1250
27.1550
27.1750
27.2050
27.2250
27.2350
27.2650
27.2850
27.3050
27.3250
27.3450
27.3650
27.3850
27.4050
search bank: SR2 FRS/GMRS/MURS band
Receive Mode: FM
Ch.
Frequency
(MHz)
Ch.
02
Frequency
(MHz)
01
462.5625
462.5875
40
Download from Www.Somanuals.com. All Manuals Search And Download.
Beyond the Basics
03
05
07
09
11
13
15
17
19
21
23
25
27
462.6125
462.6625
462.7125
467.5875
467.6375
467.6875
462.5500
462.6000
462.6500
462.7000
151.8200
151.9400
154.6000
04
06
08
10
12
14
16
18
20
22
24
26
462.6375
462.6875
467.5625
467.6125
467.6625
467.7125
462.5750
462.6250
462.6750
462.7250
151.8800
154.5700
search bank: SR3 police/fire band
Receive Mode: FM
Group
Frequency (MHz)
33.420 – 33.980
37.020 – 37.420
39.020 – 39.980
42.020 – 42.940
44.620 – 45.860
45.880
Step (kHz)
0
20
20
20
20
40
45.900
45.940 – 46.060
46.080 – 46.500
40
20
41
Download from Www.Somanuals.com. All Manuals Search And Download.
Beyond the Basics
1
153.770 – 154.130
154.145 – 154.445
154.650 – 154.950
155.010 – 155.370
155.415 – 155.700
155.730 – 156.210
158.730 – 159.210
166.250
60
15
15
60
15
60
60
170.150
2
3
453.0375 – 453.9625 12.5
458.0375 – 458.9625 12.5
460.0125 – 460.6375 12.5
465.0125 – 465.6375 12.5
851.0125 – 860.9875 25
866.0125 – 868.9875 12.5
search bank: SR4 aircraft
Receive mode: AM
Frequency (MHz)
Step (kHz)
8.33
108.000 – 136.99166
All scanners tune by steps. Your RadioShack scanner
uses steps consistent with the latest US or worldwide
standards. If you enter a non-valid step frequency, any
scanner will tune to the next step. Some scanner designs
do this without showing the correct step in the display.
This scanner will show the actual tuned frequency in the
display. Because steps are so close together, the audio
quality will not be affected by the offset.
Notes
42
Download from Www.Somanuals.com. All Manuals Search And Download.
Beyond the Basics
search bank: SR5 amateur band
Receive mode: FM
Group
Frequency (MHz)
Step (kHz)
0
1
2
3
4
5
28.0000 – 29.7000
50.0000 – 54.0000
144.0000 – 148.0000
222.0000 – 225.0000
5
5
5
5
420.0000 – 450.0000 12.5
1240.0000 –
1300.0000
6.25
search bank: SR6 programmable limit search
Receive mode: FM (Default setting)
searching active frequencies in a range
You can program the desired frequency range for a search.
1. Repeatedly press SRCH to select SR6.
2. Press PGM then SRCH. Enter SR6 Search Range Limits: appears
and the cursor blinks L on the third line for the lower-end
limit frequency.
3. Use the number keys and ./DELAY to enter the desired
lower-end limit frequency (including the decimal point).
4. Press ENT to set the frequency. The cursor moves to U.
If the entered frequency is incorrect, Invalid Freq. briefly
appears.
5. Enter your desired upper-end frequency and press ENT.
6. Press SRCH to start searching.
43
Download from Www.Somanuals.com. All Manuals Search And Download.
Beyond the Basics
7. Rotate SQ clockwise and leave it set to a point just after
the rushing sound stops. When the scanner finds an
active frequency, it stops searching.
You can copy and save a frequency into a specified bank,
Notes
hannel, or priority channel when the scanner finds an
active frequency. See “Using Frequency Copy” to save
the frequency. The frequency copy works only in search
banks 1 through 6.
While the scanner is searching, you can use the seek
search by pressing FUNC then 7. Seek Search ON.
appears on the bottom line. The scanner stops at an
active frequency for five seconds and restarts searching
automatically. The scanner repeats this operation.
You can set Zeromatic on or off by pressing FUNC then 0. Press
FUNC then 0 again to reverse the Zeromatic setting. Whenever
this feature is turned on, Zeromatic ON. briefly appears then ZM
appears at the right of the second line and the scanner stops
at the correct frequency. When you turn this feature off, ZM
changes to small caps (zm) and the scanner stops when it
detects an active signal. Zeromatic functions only in search
banks 3, 4, 5 and 6.
There are several group banks in SR3 Police/Fire and SR5
Amateur bands. You can turn off or on the groups by
pressing the group numbers. For example to turn off 0, press
0.
In the Air and Limit search bands, press FUNC then press e to
start searching up from the lowest frequency or press d to
start searching down from the highest frequency.
f you press PSE while searching, the scanner stops
Notes
searching and *** PAUSED *** appears. Press PSE again,
and the scanner resumes searching.
44
Download from Www.Somanuals.com. All Manuals Search And Download.
Beyond the Basics
manually tuning a frequency
You can manually set the scanner to move through all
receivable frequencies, or select a specific frequency as a
starting point.
1. Press TUNE. The currently-tuned frequency , *** PAUSED
***, and Fine Tune Mode appear.
2. Use the number keys to enter the frequency where you
want the scanner to start.
3. Press ENT.
4. Press PSE. The scanner starts the tune operation. To
change the tune direction, press e or d to tune up or
down. When the scanner finds an active frequency, it
stops on the frequency.
5. You can press FUNC TUNE while the scanner is stopped
on a frequency in MANUAL mode to begin the TUNE
function from that frequency. For example, if the scanner
is stopped in MANUAL mode on channel 144 with
frequency 145.31000 MHz, pressing FUNC TUNE will enter
TUNE mode and automatically set the TUNE frequency
for 145.31000 MHz.
listening to the weather band
The FCC (Federal Communications Commission) has
allocated channels for use by the National Oceanic and
Atmospheric Administration (NOAA). Regulatory agencies in
other countries have also allocated channels for use by their
weather reporting authorities.
NOAA and your local weather reporting authority broadcast
your local forecast and regional weather information on one
or more of these channels.
45
Download from Www.Somanuals.com. All Manuals Search And Download.
Beyond the Basics
listening to a weather channel
To hear your local forecast and regional weather information,
press WX. Your scanner scans through the weather band then
stops within a few seconds on the next available weather
broadcast.
SAME standby mode
The National Weather Service precedes each weather alert
with a digitally encoded SAME (Specific Area Message
Encoding) signal, then a 1050 Hz tone. The SAME signal
includes a FIPS (Federal Information Processing Standard)
area code, and an event code that corresponds with the
type of alert being sent. You can configure your scanner to
operate in SAME Standby mode, where it monitors a selected
weather radio station for SAME alerts for areas you specify.
You can program your scanner with up to 10 FIPS codes for
the areas you desire. The National Weather Service maintains
To configure your scanner for SAME Standby mode, follow
these steps:
1. Press WX until you identify the weather station with the
strongest signal for your location.
2. Press FUNC, and then PGM to access the FIPS code entry
table.
3. Use the e or d keys to select the desired FIPS code
storage location.
4. Use the numeric keys to enter the desired FIPS code,
and then press ENT to store the code. Press TEXT to label
the code entry with an alphanumeric text table if desired.
Repeat this process for all the FIPS codes that you wish to
store.
5. Press L/OUT to lock out or enable specific FIPS entries.
46
Download from Www.Somanuals.com. All Manuals Search And Download.
Beyond the Basics
6. Press WX to exit the FIPS code entry table.
Press WX then a number key to quickly review stored FIPS
Notes
codes. Press L/OUT to toggle lockout status.
Your scanner can also detect the 1050 Hz weather alert
tone when a weather channel is set as the priority
channel and weather priority operation is enabled. (see
“Priority”). In this mode all alerts are received. FIPS
settings are ignored.
The scanner sounds an alert or beep when it receives the
SAME code. If you do not stop the alert (or beep) for five
minutes, the alert stops and the scanner beeps every ten
seconds. If the scanner receives a new message after five
minutes, it sounds the alert or beep. To stop the sound
and ready the scanner to receive a new alert signal before
the five minute time out, press any key except
.
7. Press FUNC, and then WX to initiate SAME standby. The
scanner will monitor the selected weather radio station for
alerts with FIPS codes that match the codes you entered
in the FIPS entry table. To exit SAME standby, press FUNC,
and then WX.
WX Alert and beep tone confirmation
1. To test the WX alert, press WX for more than 2 seconds
while SAME Standby appears.
The display indicates the type of message, and the scanner
sounds an alert or series of beeps. The beeps automatically
change every 3 seconds.
2. Press any key except to stop test sound mode.
47
Download from Www.Somanuals.com. All Manuals Search And Download.
Beyond the Basics
Skywarn
Many areas of the country have amateur radio repeaters
that have been designated as “Skywarn” repeaters. During
times of severe weather, these repeaters are used to relay
reports of severe weather directly to meteorologists at a local
National Weather Service (NWS) forecast office. Using the
Skywarn feature in your scanner, you can easily jump to one
of three Skywarn repeater frequencies and monitor these
reports, in many cases hearing about severe weather in your
area instantly as it occurs.
This function lets you quickly move to the skywarn channels
(channels 997 through 999) from any mode except SAME
standby by pressing and holding WX about 1 second. The
scanner displays Skywarn-1 in the fourth line. The scanner
d
has 3 Skywarn channels. Press e or to select different
Skywarn channels.
To activate this function, you must program your desired
Notes
Skywarn frequencies into the Skywarn channels.
using frequency copy
You can copy a frequency into a specified channel, a vacant
channel in a specified bank, or a priority channel. However,
you cannot copy a frequency from the Marine search band.
copying a frequency into a specified channel
You can copy a frequency into a specified channel when
the scanner stops on that frequency during search mode or
manual tuning.
1. Press FUNC then PGM when you find a frequency. Store
in ChXXX ? appears on the bottom line. After about 1
second, the frequency to be copied flashes.
48
Download from Www.Somanuals.com. All Manuals Search And Download.
Beyond the Basics
2. Press the desired bank and the channel number where
you want to store the frequency. The display indicates
the bank and channel number. After about 1 second, the
frequency to be copied flashes.
3. Press ENT. All the conditions such as receive mode and
delay condition are copied onto the channel. Channel
Stored! briefly appears. The scanner automatically returns
to search mode.
If you try to copy a frequency which is already stored, the
scanner sounds the notice tone 3 times after you press ENT.
Dupl.Freq. ChXXX appears. If you want to copy the duplicate
frequency anyway, press ENT, or if not, press CL to cancel.
copying a frequency into an empty channel within a
bank
You can copy a frequency into a vacant channel in a
specified bank when the scanner stops on the frequency
during search or tune mode.
1. Press FUNC then ENT when you find a frequency you want
to copy. Bank 9 Store? appears.
2. If you want to copy the frequency into bank 9, press ENT.
It is stored in the first available vacant channel in the
bank. Or, press your desired bank number to store, then
press ENT. Channel Stored! appears for 2 seconds. All the
conditions such as receiving mode and delay condition
are copied on the channel. After about 2 seconds, the
scanner automatically returns to search mode.
3. If you try to copy a frequency which is already stored, the
scanner sounds the notice tone 3 times after you press
ENT. Dupl.Freq. ChXXX appears on the third line. If you
want to copy the duplicate frequency anyway, press ENT,
or if not, press CL to cancel.
49
Download from Www.Somanuals.com. All Manuals Search And Download.
Beyond the Basics
copying a frequency into the priority channel
You can copy a frequency into the priority channel (see
“Priority”) when the scanner stops on the frequency during
Search, Scan, Manual, Tune, or WX mode.
Press FUNC then PRI when the frequency appears. The display
flashes twice and the frequency is copied to the priority
channel.
Signal Stalker II
Your scanner’s Signal Stalker II feature provides a powerful
new tool for you to rapidly detect, monitor and store
frequencies for nearby radio transmissions. The Signal
Stalker II feature is similar in functionality to portable
frequency counters that cost much more than your scanner,
but provides many advantages over typical portable
frequency counters. For example:
The Signal Stalker II allows you to sweep the entire range of
your scanner’s design frequencies, or you can specify those
frequency ranges that you wish to sweep and exclude ranges
that you do not want to sweep. This allows you to omit
frequency ranges with constant strong frequency activity,
such as those with paging or broadcast transmitters. Many
portable frequency counters will remain locked to a nearby
constant signal, such as a paging or broadcast transmitter,
and will not function properly until you have left the vicinity
of the transmitter.
The Signal Stalker II feature is more sensitive than portable
frequency counters and will detect transmissions at a greater
distance. You can activate the Attenuator to reduce the
sensitivity if desired.
Once an active frequency is found, the transmission is played
through your scanner’s speaker, and you can quickly store it
in any of your scanner’s memory locations.
50
Download from Www.Somanuals.com. All Manuals Search And Download.
Beyond the Basics
using Signal Stalker II
Your scanner’s Signal Stalker II functions when you press
and hold
for approximately 1 second. The Signal Stalker
II function can be set to watch for activity on all band
frequencies or Police/Fire frequencies only. To change the all
bands to police/fire or vice versa, press FUNC then
.
You can also turn on/off frequency sub-bands using the
corresponding number keys while Signal Stalker II is active.
Priority mode is not available while using the Signal
Stalker II.
Notes
Press FUNC then e or d, you can change the normal Signal
Stalker II operation to the Special Signal Stalker II operation.
In the Special Stalker operation, Sp. Stalker appears and the
frequency range is divided by 1 MHz segment. If you lock
out 5 frequencies within a 1 MHz segment, the scanner will
skip that segment in subsequent sweeps. See “Using Signal
Stalker II with Lockout” below.
using Signal Stalker II with lockout
The scanner’s lock out feature can be used to bypass
unwanted transmissions while using the Signal Stalker II.
Press L/OUT when the scanner is stopped on an undesired
transmission. Press FUNC L/OUT to review or clear locked out
frequencies in the Signal Stalker II. You can lock out 150
frequencies while searching all bands and 50 frequencies
while searching Police/Fire frequencies.
Signal Stalker II functions by rapidly sweeping through the RF
spectrum in 1 MHz segments. If RF signal energy is detected
in a 1 MHz segment, Signal Stalker II will sweep through the
1MHz segment in finer steps until the source of the RF signal
energy is found.
Certain segments of RF spectrum are used by high power
transmitters, such as paging transmitters. The Signal Stalker
II can detect these transmitters easily, even at great distances
51
Download from Www.Somanuals.com. All Manuals Search And Download.
Beyond the Basics
due to their high transmitter output power. You can press
L/OUT when the Signal Stalker II stops on these undesired
transmissions to prevent the Signal Stalker II from stopping
on them in future sweeps, however, the Signal Stalker II will
still see their RF signal energy when sweeping through the 1
MHz segment. This will cause the Signal Stalker II to execute
another fine step search of the 1 MHz segment. Of course, if
you have locked out the undesired transmissions, the Signal
Stalker II will not stop on them again, however, the overall
sweep performance of the Signal Stalker II will be impacted.
Signal Stalker II features a special lockout mode that causes
the scanner to skip a 1 MHz segment if five or more lockouts
exist in that 1 MHz segment. To activate this mode, press
FUNC e while in the Signal Stalker II mode. If a 1 MHz segment
contains 5 or more lockouts it will be skipped entirely while
Signal Stalker II is sweeping. Use FUNC L/O to review or clear
locked Signal Stalker II frequencies.
To clear a locked-out frequency, select that frequency, then
press CL.
scanning the channels
To begin scanning channels or to start scanning again after
monitoring a specific channel, press SCAN.
ou must store frequencies into channels before the
Notes
canner can scan them. The scanner does not scan
through empty channels.
To change the scanning direction, press e or d.
The scanner scans through all channels (except those you
have locked out) in the active banks (see “Turning Channel-
Storage Banks Off and On”and “Locking Out Channels or
Frequencies”).
turning channel-storage banks off and on
To turn off banks while scanning, press the bank’s number
52
Download from Www.Somanuals.com. All Manuals Search And Download.
Beyond the Basics
key so the bank’s number disappears. For example, to turn
off bank 1, press 1. The scanner does not scan any of the
channels within the banks you turned off.
To turn on banks while scanning, press the number key until
the bank’s number appears. For example to turn bank 1 on
again, press 1.
You cannot turn off all banks. There must be at least one
active bank.
Notes
You can manually select any channel in a bank, even if
the bank is turned off.
monitoring a single channel/power save circuit
You can monitor a single channel with your scanner by
navigating to that channel while in manual mode. The
scanner will receive traffic on the selected frequency.
Your scanner features a power save circuit that is
automatically activated any time you manually select a
channel. The power save mode works by allowing the
receiver to “sleep” briefly while waiting for a call on the
selected channel. The power save circuit is disabled when
the scanner is tuned to a channel in program mode.
using CTCSS and DCS
Your scanner’s advanced, DSP-based CTCSS and DCS
decoder allows you to listen only to the group that is of
interest to you by specifying the group’s specific CTCSS or
DCS code for a certain frequency. CTCSS and DCS can also
help reduce instances where interfering signals cause your
53
Download from Www.Somanuals.com. All Manuals Search And Download.
Beyond the Basics
scanner to stop on one channel.
When your scanner stops on a conventional frequency that is
configured for CTCSS or DCS, it checks for a match between
the transmitted and stored codes match, the scanner stops
on the transmission and allows the audio to pass to the
speaker. If the codes do not match, the scanner resumes
scan operation. If the special “search” code is in use, the
scanner will instantly display any detected CTCSS code if
programmed for CTCSS mode, or DCS code if programmed
for DCS code. You can store the detected code into the
channel memory by pressing ENT while the code is displayed.
For more information about your scanner’s receive modes,
including CTCSS and DCS, see “Understanding Your
Scanner’s Modes”. For more information on programming
memory channels for CTCSS or DCS operation, see “CTCSS
and DCS”.
deleting frequencies from channels
1. Press MAN.
2. Use the number keys to enter the channel with the
frequency you want to delete.
3. Press MAN again.
4. Press PGM to enter the program mode. M changes to P.
5. Press FUNC.
6. Press CL. The frequency number changes and 0.0000
appears.
deleting all frequencies in a channel bank
1. Press PGM.
54
Download from Www.Somanuals.com. All Manuals Search And Download.
Beyond the Basics
2. Press FUNC then the bank number you want to clear.
Bank X selected. Fn+CLR to delete all frequencies. TEXT to edit tag
appears.
3. Press FUNC then CL. Clear entire bank? Press 1 to clear all, any
other key aborts appears.
4. Press 1 to clear the selected bank’s all channel memory.
please stand by. appears while the scanner clears all channel
memory. Press any other than 1 to cancel clear.
using delay
Many conversations might have a pause of several seconds
between a query and a reply. To avoid missing a reply, you
can program a 2-second delay into any of your scanner’s
channels. Then, when the scanner stops on the channel, DLY
appears and the scanner continues to monitor the channel
for 2 seconds after the transmission stops before it resumes
scanning. The delay feature is also available while searching.
Delay is automatically set as the default for each channel
Notes
when you turn on the scanner.
To turn delay on or off, press ./DELAY. DLY (delay on) or dly
(delay off) appears on the display.
locking out channels or frequencies
You can scan existing channels or search frequencies
faster by locking out channels or frequencies that have a
continuous transmission, such as a weather channel.
locking out channels
To lock out a channel while scanning, press L/OUT when
the scanner stops on the channel. To lock out a channel
manually, select the channel then press L/OUT so lo changes to
LO on the display.
55
Download from Www.Somanuals.com. All Manuals Search And Download.
Beyond the Basics
You can still manually select locked-out channels.
Notes
remove the lockout from a channel, manually select the
channel and press L/OUT so LO changes to lo.
reviewing locked-out channels
To review all locked out channels, press MAN. Then repeatedly
alternate between pressing FUNC and then L/OUT to view each
locked-out channel. When you finish reviewing locked-out
channels, press MAN.
locking out frequencies
To lock out a frequency during a search, press L/OUT when the
scanner stops on that frequency. The scanner locks out the
frequency, then continues searching.
The scanner does not store locked out frequencies during
search.
Notes
You can lock out as many as 50 frequencies in each bank.
If you try to lock out more, L/O Memory Full! appears.
If you lock out all frequencies in one search bank and
only this search bank is activated, All ranges Locked out!
appears and the scanner does not search.
reviewing locked-out frequencies
To review the frequencies within a search bank that you
locked out:
1. Press SRCH to set search mode.
2. Press FUNC then L/OUT. The locked-out frequency and Lockout
list appear. Press e or d to review the list. The locked-out
number and the total locked-out number also appears
as Lockout XX of YY. (The tenth of thirty locked out number
would appear as Lockout 10 of 30). If the search bank has no
locked-out frequencies, No Lockout appears. Press FUNC then
56
Download from Www.Somanuals.com. All Manuals Search And Download.
Beyond the Basics
L/OUT again to cancel reviewing locked-out frequencies.
clearing a locked-out frequency
To clear a locked-out frequency, select that frequency (see
“Reviewing Locked-Out Frequencies”), then press CL.
If all locked-out frequencies are cleared within a bank, No
Lockout appears.
clearing all locked-out frequencies in a search bank
1. Press SRCH.
2. Select the search bank in which you want to clear all
locked-out frequencies.
3. Press FUNC then press L/OUT. Lockout list appears.
4. Press FUNC then 6. Clear entire list ? Press 1 to clear all, any
other key aborts appears. Press 1 to clear all locked-out
frequencies. List cleared. appears for about 2 seconds.
Press any key other than 1 to cancel clear.
priority
In addition to the 1,000 programmable memory channels, the
scanner has one priority channel.
With the priority feature, you can scan through programmed
channels and still not miss an important or interesting
transmission on a specific channel. When priority is turned
57
Download from Www.Somanuals.com. All Manuals Search And Download.
Beyond the Basics
on, the scanner checks that channel every 2 seconds, and
stays on the channel if there is activity until the activity stops.
The priority feature does not operate while the scanner
Notes
eceives a trunking voice channel or during trunking
delay time. Therefore, the priority check seems random
during peak hours.
If you program a weather channel as the priority channel,
the scanner stays in the priority channel only when the
scanner detects the weather alert tone.
This scanner cannot set a channel as the priority channel
if the channel’s receive mode is MOT, ED, or LTR.
If you press PSE while the scanner receives the priority
channel, the scanner displays *** PAUSED *** and
stays on the priority channel even after the transmission
finished.
To program a frequency in the priority channel:
1. Press MAN.
2. Use the number keys to enter the channel number which
contains the frequency you want to program as the
priority channel. Then press MAN again.
3. Press FUNC then PRI. The display blinks.
To program the priority channel directly:
1. Press PGM.
2. Press PRI.
3. Enter the frequency you want to enter into the priority
channel, then press ENT.
To program a weather channel as the priority channel:
58
Download from Www.Somanuals.com. All Manuals Search And Download.
Beyond the Basics
1. Press WX.
2. Select the weather channel you want to program as the
priority channel.
3. Press FUNC then PRI. The display flashes two times.
To turn on the priority feature, press PRI so pri changes PRI on
the display while scanning. If the scanner detects activity on
the priority channel, Priority Channel appears. Or if the scanner
detects a weather alert tone in Priority WX mode, Priority
Channel! appears for 3 seconds then changes to Weather ALERT
and the scanner sounds an alert tone.
Priority WX is only for receiving a weather alert.
Notes
When the scanner detects a 1050 Hz alert tone, priority
WX activates and you receive a weather alert.
If you program a weather frequency into the priority
channel and the scanner detects a weather alert tone on
that frequency, the scanner sounds the alert tone.
To turn off the priority feature, press PRI.
changing the receive mode
The scanner is preset to the most common AM or FM receive
mode for each frequency range. The preset mode is correct
in most cases. However, some amateur radio transmissions
and trunked systems do not operate in the preset mode. If
you try to listen to a transmission when the scanner is not set
to the correct receive mode, the transmission might sound
weak or distorted.
If you want to listen to trunking transmissions in closed
mode, you might have to change the receive mode.
To change the receive mode, repeatedly press MODE. The
receive mode changes as follows:
AM – accesses the AM mode
FM – accesses the FM mode
59
Download from Www.Somanuals.com. All Manuals Search And Download.
Beyond the Basics
CT – accesses the FM mode, CTCSS System
DC – accesses the FM mode, DCS System
MO – accesses the FM Mode, Motorola Trunking System
(with 4- or 5-digit ID code)
ED – accesses the FM Mode, EDACS Trunking System (with
4-digit decimal ID code or 5-digit AFS code)
LT – accesses the FM mode, LTR Trunking System (with 6-
digit ID code)
MO (MOT), ED, and LT modes are not available when the
Notes
canner tunes up or down through the frequency ranges
in which the trunking operation is not used.
using the attenuator
To reduce interference or noise caused by strong signals, you
can reduce the scanner’s sensitivity to these signals.
There are two attenuator modes in your scanner. One is
normal attenuator mode in which you set the attenuator
in each channel or each band/group in the search and
tune mode. The other is global mode in which you set the
attenuator only once. This setting is applied all the time in
every mode.
Press ATT to turn on or off the attenuator while the channel
number is indicated or while the scanner is searching through
bands/groups. When the attenuator is on, att changes to ATT.
When you turn it off, ATT changes to att. You cannot set the
attenuator while the scanner is scanning.
Press FUNC and then ATT to set the attenuator to its global
mode. Global ATT. appears for 2 seconds at the bottom line and
atg appears. Press ATT to turn the attenuator on or off. ATG or
atg appears on the second line.
Press FUNC and then ATT again to turn off the global attenuation
60
Download from Www.Somanuals.com. All Manuals Search And Download.
Beyond the Basics
mode. Normal ATT. appears on the bottom line for about 2
seconds.
If you turn on the attenuator, the scanner might not
eceive weak signals.
Notes
turning the key tone on and off
Each time you press any of the scanner’s keys, the scanner
sounds a tone. To turn the scanner’s key tone off or on:
1. If the scanner is on, turn OFF/VOL counterclockwise until it
clicks to turn the scanner off.
2. Turn OFF/VOL clockwise to turn the scanner on. Multi-system
Trunking Scanner appears.
3. While Multi-system Trunking Scanner appears, press 1 to turn
on the key tone or 2 to turn it off.
using the display/key backlight
Your PRO-97 features a backlit keypad and display for easy
viewing and use in dark environments. There are three
backlight modes you can choose from to control backlight
activation, Normal mode, Keypress mode, and first keypress
Ignore mode.
With Normal mode, simply press to activate the backlight.
The backlight will activate and remain on for the factory
default setting of 5 seconds. The backlight continues to
remain on while you are operating the keypad. To turn off the
backlight before it automatically turns off, press again.
With Keypress mode, the backlight will light automatically
when you press any key on the keypad, and function as
described above in Normal mode. This mode is useful if
you want the backlight to come on automatically when you
perform an operation using the keypad.
61
Download from Www.Somanuals.com. All Manuals Search And Download.
Beyond the Basics
With Ignore mode, the backlight functions as described in
Keypress mode, except that the scanner ignores the first
keypress. This mode is useful when you wish to quickly
illuminate the display and keypad without having to search
for the key. The first keypress is ignored, and the scanner
sounds the low pitched error beep to remind you that the
first key pressed to activate the backlight is ignored by the
scanner.
In any backlight mode, you can press and hold for about 1
second to force the backlight on full time. Press while the
backlight is on to turn it off.
Follow these steps to change the backlight mode and
duration:
1. If the scanner is on, turn it off and back on again. Multi-
System Trunking Scanner appears in the scanner’s display.
2. While Multi-System Trunking Scanner appears, press
.
3. Press e or d to select the desired backlight mode and
duration. Selecting 3, 5, 10, or 20 sets the backlight mode
for normal operation for the selected duration. Selecting
K3, K5, K10, or K20 sets the backlight mode for Keypress
operation for the selected duration. Selecting I3, I5, I10,
or I20 sets the backlight mode for Ignore operation for
the selected duration. Press ENT to store your selection.
62
Download from Www.Somanuals.com. All Manuals Search And Download.
Beyond the Basics
using the keylock
Once you program your scanner, you can protect it from
accidental program changes by turning on the key lock
feature. When the keypad is locked, the only controls that
operate are FUNC,
/ , SQ, and VOL.
You cannot activate the keylock while you are entering a
frequency into a channel.
To turn on the keylock, press FUNC then
/ . Key locked.
appears for about 1 second. Key locked. appears when you
press any key after locking the keypad.
To turn off the keylock, press FUNC then
/ . The scanner
beeps three times and Key unlocked. appears.
changing the display contrast
1. Press MAN.
2. Press FUNC then 9. Use Up/Down keys to set contrast, ENTER key
saves. appears.
3. Press e or d to select the contrast.
4. Press ENT to set the display contrast.
63
Download from Www.Somanuals.com. All Manuals Search And Download.
Beyond the Basics
cloning the programmed data
You can transfer the programmed data to and from another
PRO-97 scanner using an optional connecting cable with
1/8-inch (3.5 mm) phone plugs on both ends (not supplied,
available at your local RadioShack store).
“CLONE MODE” Incorrect Model appears if the scanner
Notes
eceives data from another scanner other than a PRO-97.
Follow these steps to clone the data.
1. Turn on both scanners.
2. Connect the connecting cable to each scanner’s PC/IF
jack. **CLONE MODE** Press UP to send Remove cable to exit.
appears.
3. Press e. Confirm to send data? 1 -> YES Press other key for NO.
appears.
4. Press 1 to send the data to the other unit or press any
other key to cancel the operation.
The scanner sends the data. To exit the clone mode, remove
the cable.
64
Download from Www.Somanuals.com. All Manuals Search And Download.
Beyond the Basics
trunking
how trunking works
The scanner tracks transmissions that use the Motorola Type
I and Type II (such as Smartnet and Privacy Plus) and hybrid
analog trunking systems, plus GE/ Ericsson (EDACS) and
EF Johnson (LTR) type systems extensively used in many
communication systems.
Trunking systems allocate a few frequencies to many different
users. When the mobile unit transmits a signal, one frequency
is chosen from among the allocated frequencies in that
trunking system. The user’s ID talk group is sent with the
signal.
To receive trunking signals, you must store all the trunking
control frequencies for Motorola systems or all the trunking
group frequencies for EDACS and LTR in one bank (see
“Storing Known Frequencies into Channels”) and input ID
codes in the ID memory (see “Storing Talk Group IDs”).
Your PRO-97 automatically calculates Motorola voice
channel frequencies when it decodes the control channel.
This eliminates the need to enter all the Motorola group
frequencies.
The control channels are subject to change depending on the
day. Therefore enter all the control frequencies in the same
bank. If you do not know which is the control channel, it is
better to enter all the system frequencies into the same bank.
When the scanner decodes the Motorola control channel
and finds the voice channel, the scanner displays the control
channel memory location on the top line, the received
frequency with VC (voice channel) on the second line, the
bank and control channel memory location number on the
third line and the Motorola ID number on the bottom line.
65
Download from Www.Somanuals.com. All Manuals Search And Download.
Beyond the Basics
To listen to the transmission, the mode of the
Notes
programmed channel must be the same as that of the
trunking channel (MO, ED, or LT).
When an ID code is received, the ID list for the bank is
searched, and if found, the text name stored for the ID
appears. If not found, scanning resumes immediately unless
the bank is in open trunking mode.
There might be more than one talk group transmitting at
Notes
a time in some Motorola trunking systems. If you set the
scanner to manually tune in Motorola trunking mode, you
will hear the talk group on that channel, but the display
will alternate between all active IDs.
Frequency fleet map and talk group information are also
widely available on the Internet (for example, at www.
trunkscanner.com).
In the past, groups that transmit frequently, such as police
departments, could transmit on only a few frequencies. This
resulted in heavy traffic and often required 2-way radio users
to wait for a specific frequency to clear before transmitting.
Trunked systems allow more groups of 2-way radio users
to use fewer frequencies. Instead of selecting a specific
frequency to transmit on, a trunked system chooses one of
several frequencies when the 2-way radio user transmits. The
system automatically transmits the call on that frequency,
and also sends a code that identifies that 2-way radio user’s
transmission on a control channel.
Your scanner lets you easily hear both the call and response
transmissions for that 2-way radio user and therefore follow
the conversation. For EDACS and Motorola (above 406 MHz
range), the scanner monitors the control channel between
each transmission to identify talk groups. For some Motorola
(under 512 MHz range) and LTR systems, the scanner uses
the subaudible data sent with each transmission to identify
talk groups.
66
Download from Www.Somanuals.com. All Manuals Search And Download.
Beyond the Basics
setting squelch for trunking mode
Your scanner automatically mutes the audio during trunk
scanning when it decodes control channel data. However,
we recommend you turn SQ clockwise and leave it set to a
point just after the rushing sound stops. This lets the scanner
quickly acquire the data channel.
programming trunking frequencies
You program trunking frequencies the same as non-trunked
frequencies, except that you must store the appropriate
mode (MO, ED, or LT) with each frequency.
You can scan only one type of trunked frequency, either
Notes
DACS, Motorola, or LTR in a bank at one time. You can,
however, mix conventional channels and frequencies in a
bank.
If you are programming trunked frequencies for Motorola
Type I and hybrid systems, you must first program the
fleet map (see “Programming Fleet Maps”).
If you are programming frequencies for an EDACS system
you must store them in the Logical Channel Number
order (usually listed as LCN#). For example, LCN1 would
go into channel 01 for the current bank, and LCN2 would
go into channel 02.
If you are programming frequencies for an LTR system
you must store them in the home repeater order. For
example, home repeater order 1 would go into channel
01 for the current bank, and home repeater order 2 would
go into channel 02.
Follow these steps to program trunked frequencies:
1. Press PGM and select the bank.
To move through the bank selection faster, press PGM then
UNC and hold down e or d. To move through the banks
Notes
67
Download from Www.Somanuals.com. All Manuals Search And Download.
Beyond the Basics
one at a time, repeat the sequence of PGM, FUNC then e or
d until you reach the desired bank.
2. Press TRUNK to enter the ID program mode.
3. Repeatedly press MODE to select Motorola, EDACS (GE/
Ericsson), or LTR (EF Johnson) system to scan. This sets
the talk group ID decoding method to be used for the
bank.
If you select conventional mode instead of Motorola,
Notes
EDACS, or LTR, the scanner does not scan trunked
frequencies. Trunking mode not selected, press Mode key.
appears.
4. Press PGM to enter the program mode.
5. Enter the desired trunking frequency then press ENT to
store.
68
Download from Www.Somanuals.com. All Manuals Search And Download.
Beyond the Basics
6. To enter additional trunking frequencies as subsequent
channels in the same bank, press PGM or e to access
the next open channel then enter the frequencies. (See
“Storing Known Frequencies into Channels”).
7. Press SCAN to start scanning.
If you enter a frequency that has already been entered,
Notes
he scanner sounds an error tone and displays Dupl.
Freq. and the channel number that has been duplicated.
If the dual entry is an error press CL and enter the correct
frequency. If the dual entry is intentional press ENT to
accept.
You may replace any frequency by selecting the bank and
channel, pressing PGM and entering the new frequency.
If you make an error in the entry process, press CL as often as
needed to erase the incorrect data.
programming Motorola trunking systems (UHF-Lo)
You can program the scanner to receive transmissions in
the UHF-Lo band (406-512 MHz) of the Motorola trunking
system. You can receive these transmissions by checking the
trunking system’s control channel. You must program the
system’s base frequency and offset frequency to do this.
69
Download from Www.Somanuals.com. All Manuals Search And Download.
Beyond the Basics
Base and offset frequencies vary for each type of trunking
Notes
ystem. You can get information about these frequencies
for the trunking system you want to scan using www.
trunkscanner.com, other Internet sources, or locally
published guidebooks.
If you try to program an offset frequency in the UHF-Hi bands
(806-960 MHz), the scanner ignores the entry.
Follow these steps to program Motorola trunking frequencies
in the UHF-Lo band:
1. Press PGM then TRUNK to enter the ID program mode.
2. Press FUNC and press (or hold) e or d to select the bank.
3. Press MODE and select MOT.
4. Press FUNC then 2. The display indicates Custom Range 1/3 on
first line, Base: 406.0000 on the second line, Offset: 380 on the
third line and Step:25.0kHz on the bottom line.
5. While B in Base blinks, if necessary, press the desired Base
frequency with the number keys and press ENT. Confirm
the entry. If it is incorrect, press the number keys again to
set the base frequency. After you confirm the input, press
ENT again.
6. While O in Offset blinks, if necessary, enter the offset
number and press ENT. Confirm the entry. If it is incorrect,
then press the number keys again to set the frequency.
After you confirm the input, press ENT again.
7. While S in Step blinks, repeatedly press e or d to select the
step number, 5.0, 6.25, 10.0, 12.5, 15.0, 18.75, 20.0, 25.0,
30.0, 31.25, 35.0, 37.5, 40.0, 43.75, or 50.0 kHz, then press
ENT.
8. Press PGM to enter the program mode. Store the trunking
IDs into the sub-bank in the same bank.
70
Download from Www.Somanuals.com. All Manuals Search And Download.
Beyond the Basics
programming Motorola trunking systems (800 MHz)
Follow these steps to program 800 MHz band Motorola
trunking.
On the 800 MHz trunking band, you can select a base
requency (normal or offset).
Notes
On the 900 MHz trunking band, you do not need to set the
base frequency (base, offset, step).
1. Press PGM then TRUNK to enter the ID program mode.
2. Press FUNC then e or d to select the desired bank.
3. Press MODE and select Motorola trunking mode.
4. Press FUNC then 3. Use Up/Down keys to set 800MHz Motorola ch
plan NORMAL appears.
5. Press e or d to select NORMAL or SPLINTER and press ENT.
• If you are uncertain about the base frequency, use the
default setting. The default setting is normal.
• If you cannot receive with the normal setting, change to
OFFset. The base frequency in normal is 851.0125 MHz.
The base frequency in OFFset is 851.0000 MHz.
programming fleet maps
You must set the fleet map if you want to receive a
Motorola Type I system. Fleet maps are included along with
other information about Motorola Type I systems at www.
trunkscanner.com.
Follow these steps to program a fleet map.
1. Press PGM then TRUNK.
2. For each bank you want to program, repeatedly press
FUNC. Then e or d to select the bank.
71
Download from Www.Somanuals.com. All Manuals Search And Download.
Beyond the Basics
3. Press FUNC. Then press 8. Size Code Setting appears.
4. Enter the size code supplied with the Type I system
information, referring to the instruction that appears on
the display. If the information was not supplied, try the
following common fleet maps.
Block
Size Code
1
2
3
4
5
6
7
8
0
1
2
3
4
5
6
7
S11 S4
S11 S4
S11 S4
S11 S4
S11 S4
S11 S4
S11 S4
S11 S4
S4
S4
S4
S4
S4
S4
S12 S4
S3
S10 S1
—
S4
S12 S4
S10 S10 S1
S11 S2
S4
S4
S4
S4
—
S4
S12 S4
S4
S12 S4
S4
S2
S3
S3
S4
S4
S4
S4
S4
S4
—
S12 S4
—
S4
—
S4
Block
Size Code
9
10
S0
S0
S0
S0
S0
S0
S4
S4
11
S4
S0
S0
S0
S0
S0
S0
S0
12
13
S3
S3
14
S4
S3
15
S4
S4
16
0
1
2
3
4
5
6
7
S4
S4
S0
S0
S0
S0
S0
S0
S0
S0
S0
S0
S0
S0
S0
S4
S3
S10
S10
S11 S10 S4
S4
S4
S0
S0
S0
S4
S4
S4
S11 S11
S11 S0
S0
S0
S12 S12 S12
—
—
—
72
Download from Www.Somanuals.com. All Manuals Search And Download.
Beyond the Basics
5. Press ENT for each entry. If you make a mistake, press CL
and enter the correct size code.
The default setting of the bank is for Motorola Type II.
However, if you set Type I and you want to return to Type
II, enter 15 at Step 4.
Notes
To confirm the input, repeat Steps 1-5 and press ENT. Each
time you press ENT, you confirm the size code. If you find
an error, press CL and begin again at Step 1.
6. Press SCAN to start scanning.
talk group IDs
There are 10 talk group ID banks and each ID bank has 5 sub-
banks. Each sub-bank has 30 ID locations. You can program
up to 150 talk group IDs in each bank, so you can program up
to 1,500 talk group IDs in 10 banks. When the scanner stops
on a transmission in the Motorola, EDACS, or LTR mode, it
checks to see if the ID has been stored. In the closed mode,
the scanner only stops on the transmission and displays its
text tag if you have stored and not locked out the ID. In the
open mode, the scanner always stops on a transmission, but
it displays the ID’s text tag if you have stored the ID.
storing talk group IDs
To store a talk group ID, press TRUNK when the scanner stops
on a voice channel transmission or when a talk group ID is
indicated in the manual mode. The bottom line indicates
where the ID was stored (as ID save X-XX), then it changes to
ID#XXXX.
The first X in ID save X-XX is the sub-bank number (0-4) in the
bank. XX is the number of IDs from (00-29) in each sub-bank.
If the ID has already been stored when you press TRUNK, ID
was saved appears.
73
Download from Www.Somanuals.com. All Manuals Search And Download.
Beyond the Basics
When you try to store more than 150 talk group IDs in a
Notes
bank, Memory Full! appears. Clear some talk group IDs in
order to store new ones (see “Clearing Talk Group IDs”).
Follow these steps to manually store talk group IDs or to edit
a stored ID.
1. Press PGM.
2. Press TRUNK.
3. To select the bank where you want to store the ID,
repeatedly press FUNC then e or d until you reach the
desired bank.
4. Press MODE to select MOT, ED, or LTR.
5. Repeatedly press TRUNK to select the sub-bank.
6. Press e or d to select the location where you desire to
store the ID number.
7. Enter the talk group ID and press ENT. If necessary, use the
decimal point for a hyphen.
8. If you want to tag the ID, press TEXT, enter the desired text
tag for the ID. Then press ENT (see “Text Input Chart”).
74
Download from Www.Somanuals.com. All Manuals Search And Download.
Beyond the Basics
9. To store the next ID memory in sequence, press e and
repeat Step 7.
10. Press SCAN to start scanning.
If you made a mistake in Step 4, Invalid ID value appears
and the scanner beeps when you press ENT. Start again at
Step 3.
Notes
You can enter either a decimal or AFS code for ED
(EDACS) IDs. The default setting is decimal ID entry.
When you press FUNC then 2, AFS Format appears for
about 2 seconds. Now you can enter the ID code with
AFS format.
If you entered an ID code that is already stored in another ID
channel, Dupl. ID of X-XX appears. If you want to store the ID
code, press ENT. To cancel the operation, press CL.
75
Download from Www.Somanuals.com. All Manuals Search And Download.
Beyond the Basics
talk group ID hold
You can set your scanner to follow a trunking signal that you
want to track during scanning. While the scanner is stopped
on a voice channel (VC appears), hold down TRUNK until ID
hold ON. appears.
When ID hold is activated and the scanner receives a voice
channel, the scan indication S at the first digit in the top line
changes to H.
To release ID hold, press SCAN or TRUNK.
turning an ID sub-bank on or off
Follow these steps to turn the ID sub-bank on or off during
the program mode:
1. Press TRUNK repeatedly to select the desired sub-bank.
2. Press FUNC then 1 to turn the sub-bank on if it is off or off if
it is on.
Follow these steps to turn the ID sub-bank on or off during
the scan mode:
1. Press FUNC while the scanner is stopped on a voice
channel transmission.
2. Press TRUNK. The display indicates which sub-bank is
turned on or off, and the active sub-bank number flashes.
3. Press FUNC and the number of the sub-bank you desire to
turn on or off. For example to turn sub-bank 4 on or off,
press FUNC. Then press 4.
76
Download from Www.Somanuals.com. All Manuals Search And Download.
Beyond the Basics
locking out talk group IDs
1. Press PGM.
You can only lock out talk group IDs when the scanner is
Notes
n the closed mode (see “Open and Closed Modes”).
2. Press TRUNK.
3. Press FUNC, e or d to move to the desired bank.
4. Press e or d to select the ID memory.
5. Press L/OUT to lock out the ID. lo changes to LO.
6. To remove the lockout from a trunking ID, manually select
the ID memory, and press L/OUT. LO changes to lo.
You can confirm the ID code while the scanner shows the
text when the received signal is a voice channel.
1. Press TEXT while the scanner is receiving the voice channel
and indicating the text name. The ID code appears as MOT:
XXXXXX, etc.
2. Press TEXT again to cancel.
delay function in ID indication mode
You can set the ID delay function separate from the channel
delay.
1. Press FUNC then ./DELAY while you are programming the
trunked ID. Use Up/Down keys to set ID Delay. ENTER key saves.
2.0 seconds appears.
2. Press e or d to select None, 0.5, 1.0, 1.5, 2.0, 2.5, 3.0, 3.5,
or 4.0 seconds.
77
Download from Www.Somanuals.com. All Manuals Search And Download.
Beyond the Basics
3. Press ENT.
When activated, ID delay watches the control channel
Notes
command for the delay time when the signal disappears
from the voice channel.
reviewing locked-out talk group IDs
You cannot clear all lockouts from a talk group at the same
time.
1. Press PGM then TRUNK.
2. Press FUNC. Then L/OUT. The locked out ID appears. If the
ID memory bank has no locked-out ID, you hear the low
beep tone.
clearing talk group IDs
1. Press PGM then TRUNK.
2. Press FUNC, e or d to select ID memory.
3. Press FUNC then CL.
clearing all talk group IDs in a single bank
You can clear all talk group IDs within a bank. This lets you
quickly delete all talk group IDs from a bank if you want to
use the bank to store different data (such as a new set of talk
group IDs).
1. Press PGM.
2. Press TRUNK to enter a talk group ID memory mode.
3. Select a talk group ID bank using FUNC, e or d.
4. Press FUNC then 6. Clear entire list ? Press 1 to clear all, any other
key aborts appears.
5. Press 1 to clear all talk group IDs within a bank. List cleared.
78
Download from Www.Somanuals.com. All Manuals Search And Download.
Beyond the Basics
appears.
To cancel the deletion, press any key except 1. The scanner
returns to the talk group ID memory mode.
changing the open/closed mode
1. Press MAN.
2. Press FUNC then e or d to select the channel storage bank.
3. Press FUNC then ./DELAY. Bank OPEN. or Bank CLOSED.
appears. After that message disappears, the fifteenth
digit on the second line of the display changes from + to
– or vice versa.
4. Repeat Steps 2 and 3 for each bank.
79
Download from Www.Somanuals.com. All Manuals Search And Download.
Beyond the Basics
care
Keep the scanner dry; if it gets wet, wipe it dry immediately.
Use and store the scanner only in normal temperature
environments. Handle the scanner carefully; do not drop it.
Keep the scanner away from dust and dirt, and wipe it with a
damp cloth occasionally to keep it looking new.
service and repair
If your scanner is not performing as it should, take it to your
local RadioShack store for assistance. To locate your nearest
RadioShack, use the store locator feature on RadioShack’s
(800-843-7422) and follow the menu options. Modifying or
tampering with the scanner’s internal components can cause
a malfunction and might invalidate its warranty and void your
FCC authorization to operate it.
birdie frequencies
Every scanner has birdie frequencies. Birdies are signals
created inside the scanner’s receiver. These operating
frequencies might interfere with transmissions on the same
frequencies. If you program one of these frequencies, you
hear only noise on that frequency. If the interference is not
severe, you might be able to turn SQ clockwise to omit the
birdie.
To find the birdies in your scanner, begin by disconnecting
the antenna and moving it away from the scanner. Make sure
that no other nearby radio or TV sets are turned on near the
scanner. Use the search function and scan every frequency
range from its lowest frequency to the hghest. Occasionally,
the searching will stop as if it had found a signal, often
without any sound. This is a birdie. Make a list of all the
birdies in your scanner for future reference.
80
Download from Www.Somanuals.com. All Manuals Search And Download.
Beyond the Basics
specifications
Frequency Coverage:
25–54 MHz ............................................................................ (in 5 kHz steps)
108–136.99166 MHz ........................................................ (in 8.33 kHz steps)
137–174 MHz ........................................... (in 5, 6.25, 7.5, or 12.5 kHz steps)
216.0025–225.0000 MHz ...................................................... (in 5 kHz steps)
225.025–405.975 MHz ........................................................ (in 25 kHz steps)
406–512 MHz .....................................................................(in 6.25 kHz steps)
806–823.9875 MHz .......................................................... (in 6.25 kHz steps)
849–868.9875 MHz .......................................................... (in 6.25 kHz steps)
894– 960 MHz ................................................................... (in 6.25 kHz steps)
1240–1300 MHz ............................................................... (in 6.25 kHz steps)
Memory channels ...................................................................................1000
Channel memory banks .............................................................................10
Number of memory channels per bank ..................................................100
Talk group ID memories ........................................................................1,500
ID memory banks .......................................................................................10
Sub-banks per bank .................................................................................... 5
Number of memory IDs per sub-bank ..................................................... 30
Sensitivity (20 dB S/N):
FM:
25–54 MHz ............................................................................................ 0.3 µV
108 –136.99166 MHz ............................................................................ 0.3 µV
137–174 MHz ........................................................................................ 0.5 µV
216–225 MHz ........................................................................................... 1 µV
406–512 MHz ....................................................................................... 0.5 µV
806–960 MHz ........................................................................................ 0.7 µV
81
Download from Www.Somanuals.com. All Manuals Search And Download.
Beyond the Basics
1240–1300 MHz .................................................................................... 0.7 µV
AM:
25–54 MHz ............................................................................................... 1 µV
108–136.99166 MHz ................................................................................ 1 µV
137–174 MHz ........................................................................................ 1.5 µV
216–225 MHz ........................................................................................... 3 µV
406–512 MHz ........................................................................................... 2 µV
806–960 MHz ........................................................................................... 2 µV
1240–1300 MHz ....................................................................................... 3 µV
Selectivity:
25 – 27.995 MHz at AM mode
–6 dB .................................................................................................... 5 kHz
–50 dB ................................................................................................. 6 kHz
All frequencies at AM and FM mode except 25 – 27.995 MHz at AM
–6 dB ................................................................................................. 10 kHz
–50 dB ................................................................................................ 18 kHz
Spurious Rejection (at 154.1 MHz FM)................................................. 40 dB
Scanning Rate .............................................. Up to 60 Channels per Second
Search Rate ........................................................ Up to 75 Steps per Second
Delay Time .....................................................................................2 seconds
Intermediate Frequencies (IF):
1st .................................................................................................. 380.8 MHz
2nd ................................................................................................... 21.4 MHz
3rd ..................................................................................................... 455 kHz
Priority Sampling .......................................................................... 2 seconds
Operating Temperature ............................................................ –14 to 140° F
IF Rejection:
380.8 MHz at 154.1 MHz ....................................................................... 60 dB
82
Download from Www.Somanuals.com. All Manuals Search And Download.
Beyond the Basics
21.4 MHz at 154.1 MHz ....................................................................... 100 dB
Squelch Sensitivity:
Threshold (FM and AM) ........................................................................0.5 µV
Tight (FM) .............................................................................................. 25 dB
Tight (AM).............................................................................................. 20 dB
Antenna Impedance.........................................................................50 Ohms
Audio Output Power (10% THD) ...................................................... 170 mW
Built-in Speaker ............................................................ 1 3/8 Inches (36 mm)
................................................................................... (8-ohm, Dynamic Type)
Power Requirements:
Batteries..................................................................... 4 AA Alkaline Batteries
External Power ......................................................................................9V DC
Current Drain (Squelched) ...................................................................90 mA
Battery Charge Current ......................................................................150 mA
Dimensions (HWD)........... 5 3/4 x 2 9/16 x 1 5/8 Inches (145 x 65 x 42 mm)
Weight (without antenna and batteries) ..................................8.5 oz. (240 g)
Specifications are typical; individual units might vary. Specifications and
depictions are subject to change and improvement without notice.
83
Download from Www.Somanuals.com. All Manuals Search And Download.
Beyond the Basics
initializing your scanner
If the scanner’s display locks up or does not work properly
after you connect a power source or install batteries, you
might need to initialize it.
This procedure clears all information you stored in the
Notes
scanner’s memory. Initialize the scanner only when you
are sure the scanner is not working properly.
1. Turn off the scanner, then turn it on again. Multi-system
Trunking Scanner appears.
2. Press 0 while Multi-system Trunking Scanner appears.
3. Press 1.
4. Press ENT. Initializing please stand by. appears for about 5
seconds.
Do not turn off the scanner until the initalization is
Notes
omplete. When the initialization is complete, M000
appears on the top line of the display. Bank 0 Ch 00
appears on the third line.
84
Download from Www.Somanuals.com. All Manuals Search And Download.
Beyond the Basics
The FCC wants you to know
This equipment has been tested and found to comply with the limits for a scanning
receiver, pursuant to Part 15 of the FCC Rules. These limits are designed to provide
reasonable protection against harmful interference in a residential installation.
This equipment generates, uses and can radiate radio frequency energy and, if
not installed and used in accordance with the instructions, may cause harmful
interference to radio communications.
However, there is no guarantee that interference will not occur in a particular
installation. If this equipment does cause harmful interference to radio or television
reception, which can be determined by turning the equipment off and on, the user
is encouraged to try to correct the interference by one or more of the following
measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the
receiver is connected.
scanning legally
Your scanner covers frequencies used by many different groups including
police and fire departments, ambulance services, government agencies, private
companies, amateur radio services, military operations, pager services, and wireline
(telephone and telegraph) service providers. It is legal to listen to almost every
transmission your scanner can receive. However, there are some transmissions you
should never intentionally listen to. These include:
• Telephone conversations (cellular, cordless, or other private means of telephone
signal transmission)
• Pager transmissions
• Any scrambled or encrypted transmissions
According to the Electronic Communications Privacy Act (ECPA), you are subject
to fines and possible imprisonment for intentionally listening to, using, or divulging
the contents of such a transmission unless you have the consent of a party to the
communication (unless such activity is otherwise illegal).
This scanner has been designed to prevent reception of illegal transmissions. This is
done to comply with the legal requirement that scanners be manufactured so as to
not be easily modifiable to pick up those transmissions. Do not open your scanner’s
case to make any modifications that could allow it to pick up transmissions that are
illegal to monitor. Doing so could subject you to legal penalties.
In some areas, mobile use of this scanner is unlawful or requires a permit. Check the
laws in your area. It is also illegal in many areas to interfere with the duties of public
safety officials by traveling to the scene of an incident without authorization.
We encourage responsible, safe and legal scanner use.
85
Download from Www.Somanuals.com. All Manuals Search And Download.
Beyond the Basics
glossary
Frequency — the receving signal location (expressed in
MHz). To find active frequencies, you can use frequency
guides available from your local RadioShack store, frequency
listings posted on the Internet, or the built-in search function.
Channels — programmable memory locations for the
frequencies you want to monitor. Each time the scanner finds
an active frequency, it stops and monitors the radio traffic
on that channel until the transmission ends, then resumes
scanning.
Channel Storage Banks — a storage area for a group of
channels. Channels are storage areas for frequencies.
Whereas a channel can only contain one frequency, a bank
can hold numerous channels.
Talkgroup IDs — each channel storage bank has an
associated talkgroup ID list, for a total of 10 talkgroup ID
lists. Each ID list has 5 sub-banks. Each sub-bank has 30
ID locations. You can program up to 150 talkgroup IDs in
each bank, so you can program up to 1500 talkgroup IDs
in 10 banks. When the scanner stops on a transmission in
the Motorola or EDACS mode, it checks to see if the ID has
been stored in the associated ID list. In the Closed Mode, the
scanner only stops on the transmission and displays its text
tag if you have stored and not locked out the ID. In the Open
Mode, the scanner always stops on all transmissions except
those you specifically exclude, and diplays the ID’s text tag
if you have stored the ID. For a detailed description of Open
and Closed Mode operation, see “Open and Closed Mode
Operation”.
86
Download from Www.Somanuals.com. All Manuals Search And Download.
Beyond the Basics
FAQs (Frequently Asked Questions)
The scanner is not working at all. What’s wrong?
The AC or DC adapter might not be connected. Be sure the
adapter’s barrel plug is fully inserted into the PWR DC 9V
jack. The center tip of the adapter’s barrel plug must be
set to positive. The batteries might be dead or need to be
recharged. Recharge the rechargeable batteries or replace
the standard batteries.
The scanner does not receive any stations or reception is
poor. What’s wrong?
The scanner might need to be initialized. Turn the scanner off
then on again, or initialize the scanner (see “Initializing the
Scaner”).
The scanner is on but does not scan. What’s wrong?
The squelch might not be adjusted correctly. Turn SQ
clockwise. There might only be one channel or no channels
stored in the scanner. Store frequencies into more than one
channel. The keylock might be turned on. Turn off keylock.
While scanning, the scanner lcoks on frequencies that have
an unclear transmission. What’s wrong?
Some frequencies programmed into the scanner might be
the same as “birdie” frequencies. Avoid programming “Birdie
Frequencies” or only listen to them manually.
87
Download from Www.Somanuals.com. All Manuals Search And Download.
This product is warranted by RadioShack against manufacturing defects in material and workmanship
under normal use for one (1) year from the date of purchase from RadioShack company-owned stores
and authorized RadioShack franchisees and dealers. For complete warranty details and exclusions, check
with your local RadioShack store.
RadioShack Customer Relations
200 Taylor Street, 6th Floor, Fort Worth, TX 76102
04/04
Printed in Hong Kong
GE-04D-2310
12A04
©2004. RadioShack Corporation.
All rights reserved. RadioShack and RadioShack.com are
trademarks used by RadioShack Corporation.
Download from Www.Somanuals.com. All Manuals Search And Download.
|