21-1679
Weather Alert
Handheld CB RADIO
Thank you for purchasing your
Weather Alert Handheld CB
Radio from RadioShack.
What’s Included
CB Radio
Ni-MH Battery Pack
AA Battery Case
AC Charger
Antenna
Hand Strap
Belt Clip
User’s Guide
FCC Rules
Please read this user’s guide before installing, setting up
and using your new CB radio.
Download from Www.Somanuals.com. All Manuals Search And Download.
A Look at Your CB Radio
A Look at Your CB Radio
Antenna
SQUELCH
OFF/VOLUME
Channel
Selection
"UTTONS Ÿ/ź
CH9/19 SCAN
CB/WX
H/L BEEP
Internal Microphone
LOCK/ALERT OFF
LIGHT
PTT
ꢀ0USHŸTOŸ4ALK
Internal
Speaker
Attaching the Belt Clip
To attach the belt clip,
slide it up until it locks
into place.
To remove the belt
clip, pull the tab gently
and slide the belt clip
down.
Hand Strap Hole
Tab
Belt
Clip
3
Download from Www.Somanuals.com. All Manuals Search And Download.
Powering Your CB Radio
Powering Your CB Radio
You can power your CB radio from one of these four sources:
• The supplied rechargeable Ni-MH battery pack
• Eight AA batteries (not included) using the supplied battery
case
• AC power using an AC-to-DC power supply (not included)
• Vehicle power using a DC power cord (not included)
Using the Ni-MH Battery Pack
Charge the Ni-MH battery pack (using the supplied AC charger)
FORꢀABOUTꢀꢁꢂꢀHOURSꢀPRIORꢀTOꢀUSINGꢀITꢀFORꢀTHEꢀÞRSTꢀTIMEꢃꢀØFTERWARDꢄꢀ
it takes 14-16 hours to charge the battery pack when it is fully
discharged.
You can charge the battery pack while it is installed or removed.
But the CB radio does not work during charging.
To charge the battery pack:
Connect the AC Charger to the
CHG Jack, then plug it into an AC
outlet. The CHARGE Indicator
lights red and charging starts.
Note: The supplied AC charger
is for charging only, not for
directly powering the CB.
Latch
4OŸINSTALLŸTHEŸBATTERYŸPACKꢁ
CHG Jack
Slide the battery pack onto the
CB radio until it clicks. The battery
CHARGE
PACKꢀÞTSꢀONTOꢀTHEꢀ#"ꢀRADIOꢀONLYꢀ
Indicator
one way. Do not force it.
To remove the battery pack, slide
the battery pack in the arrow
direction while holding up the
latch.
Slide to remove
battery pack
4
Download from Www.Somanuals.com. All Manuals Search And Download.
Powering Your CB Radio
#AUTIONSꢁ
• To avoid injury, do not connect the AC charger to a ceiling
outlet. After charging, disconnect the AC charger.
• You must use a Class 2 power supply that provides 16V DC
and delivers at least 200mA. The barrel plug’s center must
BEꢀPOSITIVEꢀANDꢀTHEꢀBARRELꢀPLUGꢀMUSTꢀÞTꢀTHEꢀ#"mSꢀCHG jack.
4HEꢀSUPPLIEDꢀØ#ꢀCHARGERꢀMEETSꢀTHESEꢀSPECIÞCATIONSꢃꢀ5SINGꢀ
ANꢀADAPTERꢀTHATꢀDOESꢀNOTꢀMEETꢀTHESEꢀSPECIÞCATIONSꢀCOULDꢀ
damage the CB radio or adapter.
• Always connect the AC charger to the battery pack before
you connect it to an AC outlet, and disconnect the AC
charger from the AC outlet before you disconnect it from the
battery pack.
• Overcharging your battery pack could shorten its life.
• Do not charge your battery pack at temperatures below 14°F
(–10°C) or above 131°F (55°C).
• You cannot recharge the Ni-MH battery pack using DC
power.
Recycle Rechargeable Batteries
Placing rechargeable batteries in the trash can be
harmful to the environment. Instead, recycle old
rechargeable batteries at your local RadioShack store free of
charge. RadioShack participates in the RBRC© battery recycling
program, and is committed to preserving the environment and
conserving natural resources. Call 1-800-THE-SHACK (1-800-
843-7422) for more information.
Using the AA Battery Case
1. Turn off the CB radio if it is on.
2. Pull the halves of the case apart to
open it. Insert eight AA batteries,
matching the polarity marks (+ and –).
Snap the halves of the case together
to close it.
5
Download from Www.Somanuals.com. All Manuals Search And Download.
Powering Your CB Radio
3. Slide the battery case onto the CB radio until it clicks. The
BATTERYꢀCASEꢀÞTSꢀONTOꢀTHEꢀ#"ꢀRADIOꢀONLYꢀONEꢀWAYꢃꢀ$OꢀNOTꢀ
force it.
Replace the batteries when the sound becomes weak or
distorted,
appears, or the CB radio stops working.
;
"ATTERYŸ.OTESꢁ
• Dispose of old batteries promptly and properly. Do not burn
or bury batteries.
• Use only fresh batteries of the required size and type.
• Do not mix old and new batteries, different types of batteries
(standard, alkaline, or rechargeable), or rechargeable
batteries of different capacities.
• If you do not plan to use the CB radio with batteries for two
weeks or longer, remove the batteries. Batteries can leak
chemicals that can destroy electronic parts.
Using AC Power
To power your CB radio from your home,
you will need a 12V DC power supply
that provides a minimum of 2.5A at 12V
and a DC power cord (neither included).
1. Turn off the CB radio if it is on.
2. Use the DC power cord to connect
the CB’s 12V DC PWR Jack and the
DC power supply.
3. Connect the DC power supply to an
AC outlet.
12V DC PWR Jack
4. Turn on the CB radio to use.
#AUTIONSꢁ
• You must use a Class 2 power supply that provides regulated
13.8V DC and delivers at least 2.5A. The barrel plug’s center
MUSTꢀBEꢀPOSITIVEꢀANDꢀTHEꢀBARRELꢀPLUGꢀMUSTꢀÞTꢀTHEꢀ#"mSꢀ12V
DC PWR jack. Using an adapter that does not meet these
SPECIÞCATIONSꢀCOULDꢀDAMAGEꢀTHEꢀ#"ꢀRADIOꢀORꢀADAPTERꢃ
6
Download from Www.Somanuals.com. All Manuals Search And Download.
Powering Your CB Radio
• Always connect the power supply to the CB radio before you
connect it to an AC outlet, and disconnect the power supply
from the AC outlet before you disconnect it from the CB
radio.
Using Vehicle Power
To power your CB radio from your vehicle, you will need a DC
power cord (not included). You may also need a roof-mounted
antenna to improve transmission quality and increase the
transmission range.
1. Turn off the CB radio if it is on.
2. Use the DC power cord to connect the CB’s 12V DC
PWR jack and the vehicle’s 12V power source, such as the
cigarette-lighter socket.
3. Turn on the CB radio to use.
#AUTIONSꢁ
• You must use a Class 2 power supply that provides regulated
12V DC and delivers at least 2.5A. The barrel plug’s center
MUSTꢀBEꢀPOSITIVEꢀANDꢀTHEꢀBARRELꢀPLUGꢀMUSTꢀÞTꢀTHEꢀ#"ꢀRADIOmSꢀ
12V DC PWR jack. Using an adapter that does not meet
THESEꢀSPECIÞCATIONSꢀCOULDꢀDAMAGEꢀTHEꢀ#"ꢀRADIOꢀORꢀADAPTERꢃ
• Always connect the power supply to the CB radio before you
connect it to the vehicle outlet, and disconnect the power
supply from the outlet before you disconnect it from the CB
radio.
7
Download from Www.Somanuals.com. All Manuals Search And Download.
Connecting Your CB Radio
Connecting Your CB Radio
Installing the Antenna
To install the supplied antenna, align the
two slots on the antenna connector with
the tabs on the BNC connector of the
CB radio. Push the antenna connector
to the CB radio and rotate the antenna
connector clockwise until it locks into
place.
Installing an Optional Antenna
The CB’s BNC connector allows you
to use a variety of optional antennas,
including external mobile antennas and
outdoor base station antennas.
Always use the 50-ohm, RG-58, or RG-8 coaxial cable to connect
an outdoor antenna. If the antenna is over 50 feet from the CB
radio, use the RG-8 low-loss dielectric coaxial cable.
Safety Precaution:
If an outside antenna is installed, be sure the antenna system is
grounded so as to provide protection against voltage surges and
built-up static charges. When installing the antenna, be careful not
to touch overhead power lines as contact with them might be fatal.
Connecting an External Speaker or Microphone
Connect an external speaker (not
included) to the SPK jack of your
CB radio. This mutes the CB’s
internal speaker.
SPK
Connect an external microphone
(not included) to the MIC jack of
your CB radio. This disables the
CB’s internal microphone.
MIC
8
Download from Www.Somanuals.com. All Manuals Search And Download.
Operating Your CB Radio
Operating Your CB Radio
Receiving
1. Turn SQUELCH fully anticlockwise.
2. Turn on the CB radio. A channel number and the signal
meter appear. If necessary, press CB/WX so that a channel
number and the signal meter appear.
3. Press Ÿ or ź to select the desired channel.
4. Adjust OFF/VOLUME to the desired volume level.
5. Slowly turn SQUELCH back clockwise just until the noise stops.
Note: Do not turn SQUELCH too far clockwise because you
might cut out weak signals.
RX below the signal meter indicates the CB radio is ready to
receive transmissions.
Transmitting
Test receiving transmissions on
Channel Number
your CB Radio before trying to
transmit a message.
Signal Meter
4OŸTRANSMITŸAŸMESSAGEꢁ
1. Press and hold PTT. TX
appears below the signal
meter and the signal meter
shows the output level. Hold
the CB radio 2–3 inches from
your mouth and speak in a
normal voice to the internal microphone.
ꢅꢃꢀ 7HENꢀYOUꢀÞNISHꢀSPEAKINGꢄꢀRELEASEꢀPTT.
.OTESꢁ
• If you transmit a message while the CB radio is displaying a
weather alert (see Understanding Digital Weather Alert), the alert
tone stops and WX displays steadily. To stop the alert tone
without transmitting a message, press LOCK/ALERT OFF.
9
Download from Www.Somanuals.com. All Manuals Search And Download.
Operating Your CB Radio
• To avoid overheating the internal circuit, do not press and
hold PTT nonstop for over two minutes.
Safety Precaution
Your wireless hand-held portable transceiver contains a low power
transmitter. When the Push-to-Talk (PTT) button is pushed it sends
out radio frequency (RF) signals. The device is authorized to
operate at a duty factor not to exceed 50%. In August 1996, the
Federal Communications Commissions (FCC) adopted RF exposure
guidelines with safety levels for hand-held wireless devices.
To maintain compliance with the FCC’s RF exposure guidelines
hold the transmitter and antenna at least 1 inch (2.5 centimeters)
from your face and speak in a normal voice, with the antenna
pointed up and away from the face. If you wear the handset
on your body while using the headset accessory, use only the
supplied belt clip for this product and when transmitting, take it
out of the belt to ensure that the antenna is at least 1 inch (2.5
centimeters) from your body.
Settings
High/Low Power Level
Press H/L BEEP to switch
between low power level (LOW
appears) and high power level.
Note: Low power level reduces the range of the CB radio.
Backlight
Press LIGHT to turn on the backlight; press again to turn off. The
backlight turns off automatically after 10 seconds.
Key Tone
To activate the key tone, press and hold H/L BEEP for 2
seconds. ͈Gappears. The CB radio sounds a beep when you
press any key except PTT.
To disable the key tone, press and hold H/L BEEP for 2 seconds
again so that ͈Gdisappears.
10
Download from Www.Somanuals.com. All Manuals Search And Download.
Operating Your CB Radio
Key Lock
To activate key lock, press and hold LOCK for 2 seconds.
6
appears. This locks all keys except PTT and LIGHT. To
unlock key control, press and hold LOCK for 2 seconds again.
Power Save
If you do not press any key or if the CB radio does not receive
any signal for about 10 seconds, the CB radio automatically
enters power save mode. P. SAVE ßASHESꢃ
Scanning Channels
1. Press CB/WX to select the CB or weather mode.
2. Press and hold CH9/19 SCAN for 2 seconds. SCAN appears,
and the CB radio scans through all channels in the selected
band. When it receives a strong signal, scanning stops.
3. To deactivate scanning, press and hold CH9/19 SCAN for 2
seconds or press the Ÿ or źꢀkey.
.OTESꢁŸ
pꢀ 7HENꢀYOUꢀTURNꢀONꢀTHEꢀ#"ꢀRADIOꢀFORꢀTHEꢀÞRSTꢀTIMEꢄꢀTHEꢀSCANꢀ
feature is automatically set to ON in the weather band.
• To change weather channels manually, press the Ÿ or ź key.
Using Channels 9 and 19
Channel 9 is reserved for motorist assistance and for reporting
emergency information about accidents, hazardous road
conditions, etc. Channel 19 is used by truck drivers for general
communication purposes.
Press CH9/19 SCAN once to select channel 9, press again
to select channel 19, press again to return to the previously
selected channel.
.OTESꢁŸ
• When you select channel 9 or 19, you cannot press Ÿ or ź to
change channels.
• Always give priority to emergency messages on channel 9.
11
Download from Www.Somanuals.com. All Manuals Search And Download.
Operating Your CB Radio
Listening to the Weather Band
The FCC has allocated channels for use by National Oceanic
and Atmospheric Administration (NOAA). Regulatory agencies
in other countries have also allocated channels for use by their
weather reporting authorities.
NOAA and your local weather reporting authority broadcast
your local forecast and regional weather information on one or
more of these channels.
Listening to a Weather Channel
Weather Channel
Press CB/WX to select weather
mode. WX appears. The CB
radio scans through the weather
channels and then stops on the
strongest channel. Press CB/WX
again to return to CB mode.
Note: You cannot adjust the
power level or switch to
channel 9 or 19 while listening to a weather channel.
Turning Digital Weather Alert On and Off
• Digital weather alert automatically scans in the background
when you select the CB mode, unless you turn it off.
• Press LOCK/ALERT OFF to turn digital weather alert on and off.
In CB mode, WX displays as described below.
WX Appearance
WX not present
WX flashes
Weather Alert
Weather Signal
Not scanning for
signal
Not on
On
No signal found
Signal found and
locked in
WX displays steadily
On
WX displays steadily for 2
seconds and then flashes
twice
Signal found;
scanning for signal
On
12
Download from Www.Somanuals.com. All Manuals Search And Download.
Operating Your CB Radio
Understanding Digital Weather Alert
The weather service precedes each weather alert with a digitally-
ENCODEDꢀ3Ø-%ꢀ 3PECIÞCꢀØREAꢀ-ESSAGEꢀ%NCODINGꢆꢀSIGNALꢄꢀTHENꢀ
a 1050 Hz tone. When your local weather station broadcasts
a weather alert signal, the CB radio sounds an alert tone and
displays a message showing the alert level.
SAME Event Code
Alert Tone
-ESSAGE
Watch alert
10 seconds
A (Watch)
WCH (Watch)
W (Warning)
TOR (Tornado)
SVR (Severe)
Warning alert
10 seconds
WRN (Warning)
ADV (Advisory)
S (Statement)
RWT (Test)
Statement alert
10 seconds
.OTESꢁ
• The CB radio does not display the actual location referenced
by SAME messages. It uses only the message portion of the
SAME signal.
• If severe weather threatens, do not wait for an alert tone;
tune to the weather broadcast and monitor the weather
information.
• If a weather signal ends, the CB radio beeps three times
(when the key tone is turned on) and only when the weather
SIGNALꢀENDSꢀTHEꢀÞRSTꢀTIMEꢄꢀTHENꢀWXꢀßASHESꢀTOꢀINDICATEꢀTHEREꢀISꢀ
no signal.
13
Download from Www.Somanuals.com. All Manuals Search And Download.
Additional Information
Additional Information
Legal Use of Your CB Radio
The CB Radio service is a private, two-way, short-distance voice
communications service for personal or business activities. For
rules regarding legal CB radio use, see Part 95, Subpart D: FCC
Rules for Operating a Citizens Band (CB) Radio published by the FCC.
Common Uses for a CB Radio
pꢀ 7ARNꢀOFꢀTRAFÞCꢀTIEꢇUPSꢀAHEADꢃ
• Help truck drivers and delivery personnel learn road and
TRAFÞCꢀCONDITIONSꢀANDꢀGETꢀASSISTANCEꢀINꢀLOCATINGꢀDESTINATIONSꢃ
• Provide fast help in the event of emergency or breakdown.
• Help construction crews coordinate the activities of different
work crews.
pꢀ ØSSISTꢀCOMMUNICATIONꢀBETWEENꢀSECURITYꢀOFÞCERSꢃ
• Provide weather and road information.
• Contact friends or other CB users on trips.
pꢀ +EEPꢀINꢀTOUCHꢀWITHꢀYOURꢀOFÞCEꢀORꢀHOMEꢃ
pꢀ "RINGꢀMOREꢀFUNꢀFORꢀCAMPINGꢄꢀÞSHINGꢄꢀANDꢀOTHERꢀSPORTSꢈꢀHELPꢀ
LOCATEꢀAꢀFRIENDꢀORꢀÞNDꢀOUTꢀWHATmSꢀCOOKINGꢀBACKꢀATꢀCAMPꢃ
Transmission Courtesy
• Wait for a pause in someone else’s transmission before you
ask for a break.
• If you do not receive an answer to your call after a second
attempt, sign off and wait several seconds before trying again.
• Do not hold down PTT when you are not talking. (This is
called dead keying.)
• Assist callers with directions, information about road
conditions, and any other reasonable requests.
Transmission Range
The maximum range and quality of CB transmissions vary
depending on the following conditions:
14
Download from Www.Somanuals.com. All Manuals Search And Download.
Additional Information
• Type and quality of the antenna.
• Height of the antenna’s mounting location (the higher the
antenna, the better the signal’s range).
• Surrounding terrain (mountains and tall buildings limit the range).
• Weather conditions.
• Number of nearby CBs operating on the same channel.
Note: Your CB radio’s transmission range is generally line-of-
sight. To ensure maximum range, always keep the battery
pack fully charged or use fresh batteries.
Common 10-Codes
Citizens Band radio operators have largely adopted the 10-
codes for standard questions and answers. These codes permit
faster communication and better understanding in noisy areas.
The following table lists some of the more common codes and
their meanings:
Code
Meaning
Code
Meaning
10-1 Receiving poorly
10-2 Receiving well
10-3 Stop transmitting
10-4 OK, message received
10-5 Relay message
10-6 Busy, stand by
10-7 Out of service
10-8 In service
10-22 Report in person to____
10-23 Stand by
10-25 Can you contact____
10-26 Disregard last information
10-27 I am moving to channel
10-28 Identify your station
10-32 I will give you a radio check
10-33 %MERGENCYŸTRAFÚC
10-9 Repeat message
10-36 Correct time is____
Transmission completed,
standing by
10-10
10-37 Wrecker needed at____
10-11 Talking too rapidly
10-12 Visitors present
10-38 Ambulance needed at____
10-41 Please turn to channel____
Advise Weather/Road
conditions
10-13
10-42 4RAFÚCŸACCIDENTŸAT????
10-17 Urgent business
10-18 Anything for us?
10-43 4RAFÚCŸTIEꢀUPŸAT????
10-50 Break channel
10-19 Nothing for you. Return to base 10-62 Unable to copy; use telephone
10-20 My location is____
10-21 Call by telephone
10-70 Fire at____
15
Download from Www.Somanuals.com. All Manuals Search And Download.
Additional Information
Note: Although this table lists the meanings of the 10-codes
in the form of a statement, they can also be phrased
as questions (10-6: Are you busy? 10-20: What is your
location?)
Frequency Range
Your CB radio receives and transmits on the following 40 CB
channels:
Frequency
ꢀ-(Z
Frequency
ꢀ-(Z
Frequency
ꢀ-(Z
Channel
Channel
Channel
1
2
26.965
26.975
26.985
27.005
27.015
27.025
27.035
27.055
27.065
27.075
27.085
27.105
27.115
27.125
15
16
17
18
19
20
21
22
23
24
25
26
27
27.135
27.155
27.165
27.175
27.185
27.205
27.215
27.225
27.255
27.235
27.245
27.265
27.275
28
29
30
31
32
33
34
35
36
37
38
39
40
27.285
27.295
27.305
27.315
27.325
27.335
27.345
27.355
27.365
27.375
27.385
27.395
27.405
3
4
5
6
7
8
9
10
11
12
13
14
In addition, your CB radio can receive these weather service
channels:
Frequency
ꢀ-(Z
Frequency
ꢀ-(Z
Frequency
ꢀ-(Z
Channel
Channel
Channel
1
2
3
162.400
162.425
162.450
4
5
6
162.475
162.500
162.525
7
162.550
16
Download from Www.Somanuals.com. All Manuals Search And Download.
Specifications
Specifications
Receiver
Frequency Coverage........ 26.965~27.405 MHz, 162.400~162.550 MHz
Sensitivity...........................................................................1 μV for 10 dB
Adjacent Channel Rejection ((S+N)/N)........................................... 60 dB
Squelch................................................................Adjustable from 0.5 μV
Audio Output Power (10% THD)................................................ 400 mW
Current Drain............................. 80 mA (Standby); 400 mA (Max. Audio)
Transmitter
Frequency Coverage............................................... 26.965~27.405 MHz
Power Output........................................................ 3 W (High); 1 W (Low)
Conducted Spurious Emission Harmonics ..................................... 60 dB
Type of Modulation ............................................................................. A3
Frequency Tolerance ....................................................................0.002%
Antenna Impedance.........................................................................50 Ÿꢀ
Current Drain (@ Max. Modulation)...............1.3 A (High); 700 mA (Low)
Dimensions (H× W× D) .......... 7.4 × 2.6 × 1.8 inch (186 × 65 × 47 mm)
Weight (including battery pack & antenna)...................... 18.3 oz (520 g)
3PECIÞCATIONSꢀAREꢀSUBJECTꢀTOꢀCHANGEꢀANDꢀIMPROVEMENTꢀWITHOUTꢀNOTICEꢃꢀ
Actual product may vary from the images found in this document.
Care
Keep the CB radio dry; if it gets wet, wipe it dry immediately.
Use and store the CB radio only normal temperature
environments. Handle the CB radio carefully; do not drop it.
Keep the CB radio away from dust and dirt, and wipe it with a
damp cloth occasionally to keep it looking new.
Modifying or tampering with the CB radio’s internal components
can cause a malfunction and might invalidate its warranty and
avoid your FCC authorization to operate it. If your CB radio is
not performing as it should, take it to your local RadioShack
store for assistance.
17
Download from Www.Somanuals.com. All Manuals Search And Download.
RF Emissions Information
RF Emissions Information
This equipment has been tested and found to comply with the limits
for a Class B digital device, pursuant to Part 15 of the FCC Rules.
These limits are designed to provide reasonable protection against
harmful interference in a residential installation. This equipment
generates, uses, and can radiate radio frequency energy and, if not
installed and used in accordance with the instructions, may cause
harmful interference to radio communications. However, there is no
guarantee that interference will not occur in a particular installation. If
this equipment does cause harmful interference to radio or television
reception, which can be determined by turning the equipment off and
on, the user is encouraged to try to correct the interference by one or
more of the following measures:
•
•
•
Reorient or relocate the receiving antenna.
Increase the separation between the equipment and receiver.
Connect the equipment into an outlet on a circuit different from that
to which the receiver is connected.
Consult your local RadioShack store or an experienced radio/TV
technician for help. If you cannot eliminate the interference, the FCC
REQUIRESꢀTHATꢀYOUꢀSTOPꢀUSINGꢀYOURꢀPRODUCTꢃꢀ#HANGESꢀORꢀMODIÞCATIONSꢀ
not expressly approved by RadioShack may cause interference and
void the user’s authority to operate the equipment.
This device complies with Part 15 of the FCC Rules. Operation is
subject to the following two conditions: (1) this device may not cause
harmful interference, and (2) this device must accept any interference
received, including interference that may cause undesired operation.
7ARNINGSꢁ
•
Any adjustment to this equipment is recommended to be
performed by or under the immediate supervision and responsibility
OFꢀAꢀPERSONꢀCERTIÞEDꢀASꢀTECHNICALLYꢀQUALIÞEDꢀTOꢀPERFORMꢀTRANSMITTERꢀ
maintenance and repair duties in the private land mobile services
ANDꢀÞXEDꢀSERVICESꢀBYꢀANꢀORGANIZATIONꢀORꢀCOMMITTEEꢀREPRESENTATIVEꢀOFꢀ
users of those services.
•
Replacement of any transmitter component (crystal, semiconductor,
etc.) for this equipment could result in violation of FCC rules.
18
Download from Www.Somanuals.com. All Manuals Search And Download.
Do Stuff
Do Stuff
Do more with your CB radio.
25-watt, 39” Whip,
Magnetic-mount
Mobile CB Antenna
-INIŸ%XTENSIONŸ3PEAKERŸ
•
Receive more, and
Transmit farther in
your car.
•
•
Clip it to your visor.
Set it on your dash.
•
13.8VDC 3-Amp Power Supply
Power up in your home.
DC Power Cord
Power up in your car.
•
•
ꢂꢃꢄꢅ7ATTŸ!MPLIÚEDŸ-OBILEŸ
%XTENSIONŸ3PEAKER
ꢄꢅ7ATTŸ(EAVYꢅDUTYŸ%XTENSIONŸ
Speaker
•
Amplify over loud noises.
•
Amplify at home or in the
car.
19
Download from Www.Somanuals.com. All Manuals Search And Download.
Limited Warranty
This product is warranted by Rad ioShack against manufacturing defects in material
and workmanship under normal use for one (1) year from the date of purchase
from Rad ioShack company-owned stores and authorized Rad ioShack franchisees
and dealers. EXCEPT AS PROVIDED HEREIN, Rad ioShack MAKES NO EXPRESS
WARRANTIES AND ANY IMPLIED WARRANTIES, INCLUDING THOSE OF
MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE, ARE LIMITED
IN DURATION TO THE DURATION OF THE WRITTEN LIMITED WARRANTIES
CONTAINED HEREIN. EXCEPT AS PROVIDED HEREIN, Rad ioShack SHALL HAVE
NO LIABILITY OR RESPONSIBILITY TO CUSTOMER OR ANY OTHER PERSON OR
ENTITY WITH RESPECT TO ANY LIABILITY, LOSS OR DAMAGE CAUSED DIRECTLY
OR INDIRECTLY BY USE OR PERFORMANCE OF THE PRODUCT OR ARISING
OUT OF ANY BREACH OF THIS WARRANTY, INCLUDING, BUT NOT LIMITED TO,
ANY DAMAGES RESULTING FROM INCONVENIENCE, LOSS OF TIME, DATA,
PROPERTY, REVENUE, OR PROFIT OR ANY INDIRECT, SPECIAL, INCIDENTAL, OR
CONSEQUENTIAL DAMAGES, EVEN IF Rad ioShack HAS BEEN ADVISED OF THE
POSSIBILITY OF SUCH DAMAGES.
Some states do not allow limitations on how long an implied warranty lasts or
the exclusion or limitation of incidental or consequential damages, so the above
limitations or exclusions may not apply to you.
In the event of a product defect during the warranty period, take the product
and the Rad ioShack sales receipt as proof of purchase date to any Rad ioShack
store. Rad ioShack will, at its option, unless otherwise provided by law: (a) correct
the defect by product repair without charge for parts and labor; (b) replace the
product with one of the same or similar design; or (c) refund the purchase price. All
replaced parts and products, and products on which a refund is made, become the
property of Rad ioShack. New or reconditioned parts and products may be used in
the performance of warranty service. Repaired or replaced parts and products are
warranted for the remainder of the original warranty period. You will be charged for
repair or replacement of the product made after the expiration of the warranty period.
This warranty does not cover: (a) damage or failure caused by or attributable to
acts of God, abuse, accident, misuse, improper or abnormal usage, failure to follow
instructions, improper installation or maintenance, alteration, lightning or other
incidence of excess voltage or current; (b) any repairs other than those provided by a
Rad ioShack Authorized Service Facility; (c) consumables such as fuses or batteries;
(d) cosmetic damage; (e) transportation, shipping or insurance costs; or (f) costs of
product removal, installation, set-up service adjustment or reinstallation.
4HISꢀWARRANTYꢀGIVESꢀYOUꢀSPECIÞCꢀLEGALꢀRIGHTSꢄꢀANDꢀYOUꢀMAYꢀALSOꢀHAVEꢀOTHERꢀRIGHTSꢀWHICHꢀ
vary from state to state.
Rad ioShack Customer Relations
300 RadioShack Circle, Fort Worth, TX 76102
12/99
Protect the environment by recycling used electronics.
Go to www.ecyclingcentral.comŸTOŸÚNDŸAŸRECYCLEŸLOCATIONŸNEARŸYOUꢀ
04A08
©2008. RadioShack Corporation.
21-1679
AO0300ABA1
Printed in China
All rights reserved. RadioShack and RadioShack.com
are trademarks used by RadioShack Corporation.
Download from Www.Somanuals.com. All Manuals Search And Download.
|