43-733.fm Page 1 Friday, September 17, 1999 8:57 AM
Cat. No. 43-733
OWNER’S MANUAL
Please read before using this equipment.
TAD-733
900 MHz Digital Spread Spectrum
Cordless Telephone and
Answering System
with Headset Jack
Download from Www.Somanuals.com. All Manuals Search And Download.
43-733.fm Page 3 Friday, September 17, 1999 8:57 AM
Hearing Aid Compatible — lets you
use this telephone with hearing aids that
have a T (telephone) switch.
TELEPHONE FEATURES
900 MHz Operation — provides better
sound and less interference than many
other cordless phones.
This telephone device has been tested
and found to comply with all applicable
UL and FCC standards.
Digital Spread Spectrum — provides
the longest range and the utmost in se-
curity. Frequencies are constantly
changing across the entire 900 MHz
band, making it difficult for anyone to
monitor your calls on scanners.
WARNING: To reduce the risk of fire or
shock hazard, do not expose this product to rain
or moisture.
CAUTION
20 Channels — scans the frequency
pairs used between the base and the
handset and automatically selects a
clear channel each time you make or re-
ceive a call.
RISK OF ELECTRIC SHOCK.
!
DO NOT OPEN.
CAUTION: TO REDUCE THE RISK OF
ELECTRIC SHOCK, DO NOT REMOVE
COVER OR BACK. NO USER-SERVICE-
ABLE PARTS INSIDE. REFER SERVICING
TO QUALIFIED PERSONNEL.
20-Number Memory Dialing — lets
you store up to 20 phone numbers in
memory for easy dialing.
This symbol is intended to alert
you to the presence of uninsu-
lated dangerous voltage within
the product’s enclosure that might
be of sufficient magnitude to con-
stitute a risk of electric shock. Do
not open the product’s case.
Any-Key Answer — lets you press any
key on the handset to answer an incom-
ing call.
Security Access-Protection Code —
helps prevent other cordless phones
from using your phone line while the
handset is off the base.
This symbol is intended to inform
you that important operating and
maintenance instructions are
included in the literature accom-
panying this product.
!
Page — lets you send a paging signal
from the base to the handset to page
someone or locate the handset when it
is away from the base.
Headset Jack — lets you connect an
optional headset (available at your local
RadioShack store) for hands-free con-
venience.
3
Download from Www.Somanuals.com. All Manuals Search And Download.
43-733.fm Page 4 Friday, September 17, 1999 8:57 AM
Important: Cordless phones such as
this one require AC power to operate.
When AC power is off, you cannot dial
out or receive incoming calls using your
TAD-733. For this reason, the TAD-733
should not be your only telephone. To
be safe, you should also have a phone
that does not require AC power to oper-
ate (not a cordless phone) so you can
still make and receive calls if there is an
AC power failure.
FCC STATEMENT
Your TAD-733 complies with Part 68 of
FCC Rules. You must, upon request,
provide the FCC Registration Number
and the REN to your phone company.
These numbers are on the label on the
back of the base.
You must not connect your phone to any
of the following:
• coin-operated systems
• party-line systems
READ THIS BEFORE
INSTALLATION
• most electronic key phone systems
Your TAD-733 conforms to federal regu-
lations, and you can connect it to most
telephone lines. However, each device
you connect to the telephone line draws
power from the telephone line. We refer
to this power draw as the device’s ringer
equivalence number, or REN. The REN
is on the label on the back of the base.
Note: Your telephone operates on stan-
dard radio frequencies, as allocated by
the FCC. Even though the security
access-protection code prevents unau-
thorized use of your phone line, it is pos-
sible for other radio units operating on
similar frequencies within a certain area
to unintentionally intercept your conver-
sations and/or cause interference. This
lack of privacy can occur with any cord-
less phone.
If you are using more than one phone or
other device on the line, add up all the
RENs. If the total is more than five (three
in rural areas), your phone might not
ring and your answering system might
not answer. If ringer operation is im-
paired, remove a device from the line.
4
Download from Www.Somanuals.com. All Manuals Search And Download.
43-733.fm Page 5 Friday, September 17, 1999 8:57 AM
CONTENTS
Preparation .............................................................................................................. 7
Selecting a Location ........................................................................................... 7
Installing the Handset’s Antenna ........................................................................ 7
Installing the Phone ............................................................................................ 7
On a Desk Top ............................................................................................. 7
On a Wall Plate ............................................................................................ 8
Connecting and Charging the Handset Battery Pack ......................................... 9
Setting the Dialing Mode and Ringers .............................................................. 11
Dialing Mode .............................................................................................. 11
Ringers ...................................................................................................... 11
Number of Rings ........................................................................................ 12
Setting The Ringer’s Volume ..................................................................... 12
Checking/Setting the Ringer Tone ............................................................. 12
Setting the Day and Time ................................................................................. 12
With the Handset ....................................................................................... 12
With the Base ............................................................................................ 13
Telephone Operation ............................................................................................ 14
Making and Receiving a Call ............................................................................ 14
Setting the Handset’s Volume .......................................................................... 14
Using Redial ..................................................................................................... 14
Using Flash ...................................................................................................... 15
Using Mute ....................................................................................................... 15
Using Tone Services on a Pulse Line ............................................................... 15
Using Page ....................................................................................................... 16
Memory Dialing ................................................................................................ 16
Storing a Number in Memory ..................................................................... 16
Entering a Pause ....................................................................................... 17
Dialing a Stored Number ........................................................................... 17
Chain-Dialing Service Numbers ................................................................. 17
Testing Stored Emergency Numbers ......................................................... 17
Using an Optional Headset .............................................................................. 17
Removing the Belt Clip ..................................................................................... 18
TAD Operation ....................................................................................................... 19
Setting the TAD to Answer Calls ...................................................................... 19
Using the Mailboxes ......................................................................................... 19
Recording an Outgoing Message ..................................................................... 19
Deleting an Outgoing Message ........................................................................ 20
Screening Calls ................................................................................................ 20
Adjusting the TAD’s Volume ............................................................................. 21
Recording Incoming Messages ........................................................................ 21
5
Download from Www.Somanuals.com. All Manuals Search And Download.
43-733.fm Page 6 Friday, September 17, 1999 8:57 AM
Recording a Memo ........................................................................................... 21
Playing Messages ............................................................................................ 22
Deleting Messages ........................................................................................... 22
Changing the Remote Operation Security Code .............................................. 23
Remote Operation ................................................................................................. 24
Using Toll-Saver ............................................................................................... 24
Using Remote
Answer-On .............................................................................................................. 24
Using Remote Commands ............................................................................... 24
Remote Commands ................................................................................... 25
Troubleshooting .................................................................................................... 26
Care and Maintenance .......................................................................................... 27
Replacing the Battery Pack .............................................................................. 28
The FCC Wants You to Know ........................................................................... 29
Lightning ........................................................................................................... 29
6
Download from Www.Somanuals.com. All Manuals Search And Download.
43-733.fm Page 7 Friday, September 17, 1999 8:57 AM
PREPARATION
SELECTING A LOCATION
INSTALLING
THE
HANDSET’S
ANTENNA
You can place the phone on a desk top
or table, or mount it on a standard wall
plate. Select a location that is:
• near an accessible AC outlet
• near a telephone line jack
Screw the antenna into
the hole at the top of the
handset.
• out of the way of normal activities
• away from electrical machinery,
electrical appliances, metal walls or
filing cabinets, wireless intercoms,
alarms, and room monitors
INSTALLING THE PHONE
On a Desk Top
The base’s location affects the phone’s
range. If you have a choice of several lo-
cations, try each to see which provides
the best performance.
1. Remove the mounting bracket by
holding in both tabs and gently pull-
ing out the wide end of the bracket.
Cautions:
You must use a Class 2
power source that supplies
!
9V DC and delivers at least
800 mA. Its center tip must be set to
positive and its plug must fit the
TAD-733's DC 9V jack. The supplied
adapter meets these specifications.
Using an adapter that does not meet
these specifications could damage
the TAD-733 or the adapter.
2. Plug one end of the supplied long
modular cord into the telephone jack
on the back of the base.
• Always connect the AC adapter to
the TAD-733 before you connect it
to AC power. When you finish, dis-
connect the adapter from AC power
before you disconnect it from the
TAD-733.
3. Plug the modular cord’s other end
into a modular phone line jack.
7
Download from Www.Somanuals.com. All Manuals Search And Download.
43-733.fm Page 8 Friday, September 17, 1999 8:57 AM
4. Insert the supplied AC adapter’s
barrel plug into the DC 9V jack on
the back of the base.
7. Plug the adapter into a standard AC
outlet. The TAD-733 beeps and 00
appears.
8. Raise the base’s antenna to a verti-
cal position.
On a Wall Plate
1. Follow Steps 1–4 under “On a Desk
Top” on Page 7.
5. Route the adapter’s cord through
the strain relief slot on the back of
the base.
2. Route the modular cord through the
left groove on the bottom of the
base and the adapter cord through
the groove below the strain relief
slot.
Strain
Relief
Slot
Strain
Relief
Slot
6. Insert the tabs on the narrow end of
the bracket into the inner pair of
slots near the bottom of the base
and snap the tabs at the wide end of
the bracket into place.
3. Route the end of the modular cord
through the hole in the bracket, and
insert the tabs on the narrow end of
the bracket into the inner pair of
slots near the top of the base.
8
Download from Www.Somanuals.com. All Manuals Search And Download.
43-733.fm Page 9 Friday, September 17, 1999 8:57 AM
4. Snap the tabs at the wide end of the
bracket into place.
CONNECTING AND
CHARGING THE
HANDSET BATTERY
PACK
The TAD-733 comes with a recharge-
able nickel-cadmium battery pack in the
handset but not connected. Before using
your phone, you must connect the bat-
tery pack and then charge it for about 15
hours.
1. Press down and slide off the battery
compartment cover.
5. Plug the modular cord into the wall
plate jack. Align the base’s keyhole
slots with the wall plate studs and
slide the base downward to secure
it.
2. Lift the battery pack out of the com-
partment, and plug its connector into
the socket inside the compartment.
The connector fits only one way.
6. Plug the AC adapter into a standard
AC outlet. The TAD-733 beeps and
00 appears.
3. Put the battery pack in the compart-
ment and replace the cover.
7. Raise the base’s antenna to a verti-
cal position.
9
Download from Www.Somanuals.com. All Manuals Search And Download.
43-733.fm Page 10 Friday, September 17, 1999 8:57 AM
4. To charge the battery pack, place
the handset on the base. The IN
USE indicator flashes for 1 second
and the CHARGE indicator auto-
matically lights after 4 seconds.
Also, check the charging contacts
on the handset and base. If the con-
tacts are dirty or tarnished, clean
them with a pencil eraser.
IN USE
Indicator
CHARGE
Indicator
• When you first use the phone after
charging or recharging the battery
pack, the phone might not work and
you might hear 3 short beeps when
you press TALK. If this happens, re-
turn the handset to the base for about
5 seconds. This resets the security
access-protection code.
Recharge the battery pack when the
LOW BATT indicator on the handset
flashes.
LOW BATT
Indicator
• About once a month, fully discharge
the battery pack by keeping the hand-
set off the base until the LOW BATT
indicator lights. Otherwise, the bat-
tery pack loses its ability to fully re-
charge.
Notes:
• You can place the handset on the
base facedown or faceup without re-
moving the belt clip. If you want to
use the hanging hole on the back of
the handset to place the handset on
the wall-mounted base faceup, re-
move the belt clip (see “Removing
the Belt Clip” on Page 18).
• If the LOW BATT indicator does not
light, but the phone does not work, re-
charge the battery pack. (The battery
pack charge might be too low to light
the indicator.)
• If the battery pack becomes weak
during a call, you hear 3 beeps and
the LOW BATT indicator flashes. End
the call as soon as conveniently pos-
sible, and recharge the battery pack
before using the phone again.
• If the CHARGE indicator does not
light when you place the handset on
the base, be sure the battery pack
and AC adapter are correctly and
securely connected.
10
Download from Www.Somanuals.com. All Manuals Search And Download.
43-733.fm Page 11 Friday, September 17, 1999 8:57 AM
• If the battery pack is completely dis-
charged or the base loses power
while the handset is away from it,
place the handset on the base to re-
set the security access-protection
code. If it was the handset that lost
power, recharge the battery pack.
2. Press TALK on the handset and lis-
ten for the dial tone. The TALK indi-
cator lights.
TALK
Indicator
• The supplied battery pack should last
for about a year. When the battery
pack loses its ability to fully recharge,
order a replacement battery pack
from your local RadioShack store
(see “Replacing the Battery Pack” on
Page 28).
3. Press any number other than 0.
Note: If your phone system requires
that you dial an access code (9, for
example) before you dial an outside
number, do not press the access
code either.
SETTING THE DIALING
MODE AND RINGERS
If the dial tone stops, you have
touch-tone service. Leave T/P set to
T.
Dialing Mode
If the dial tone continues, you have
pulse service. Set T/P to P.
Set T/P (Tone/Pulse) on the back of the
base for the type of service you have. If
you are not sure which type you have,
after you charge the handset battery
pack, do this simple test.
4. Press TALK on the handset or place
the handset on the base to hang up.
Ringers
1. Set T/P to T.
To turn off the ringers on the base, set
RINGER on the back of the base to OFF.
To turn off the ringer on the handset, set
RINGER on the left side of the handset to
OFF.
11
Download from Www.Somanuals.com. All Manuals Search And Download.
43-733.fm Page 12 Friday, September 17, 1999 8:57 AM
You can still make or receive calls using
this phone, and telephones on the same
line still ring when there is an incoming
call. The IN USE indicator on the base
and the TALK indicator on the handset
flash until you answer the call.
Checking/Setting the Ringer
Tone
You can set the TAD 733’s handset to
sound any of four ringer types. The
handset is preset to use ringer tone 1.
To change or hear the different tones,
press FLASH then 1, 2, 3, or 4 when the
phone is not in use and RINGER is set to
ON. (The tone you hear corresponds to
the last number button pressed.)
To turn on the base and handset ring-
ers, set RINGER to ON.
Number of Rings
Set the 4/7/TS switch on the back of the
base to 4, 7, or TS to select how long the
TAD waits before it answers a call (4
rings, 7 rings, or toll-saver).
SETTING THE DAY AND
TIME
You must set the day of the week and
time so the TAD can record the correct
day and time of each message. You can
set the day and time with either the
handset or the base.
Note: The system does not retain the
day and time settings when AC power
failure exceeds 2 minutes.
Note: If you plan to check your messag-
es by long distance, set the number of
rings to toll-saver (see “Using Toll-Sav-
er” on Page 24).
With the Handset
1. Press REMOTE. The REMOTE indi-
cator lights.
Setting The Ringer’s Volume
REMOTE
Indicator
To adjust the ringer’s volume when the
phone is not in use, press VOLUME
or
on the handset.
12
Download from Www.Somanuals.com. All Manuals Search And Download.
43-733.fm Page 13 Friday, September 17, 1999 8:57 AM
2. Press CHANGE ( ) then CLOCK (8).
The TAD announces the currently
set day.
With the Base
1. Hold down CLOCK until the TAD an-
nounces the currently set day.
3. To change the day, repeatedly press
SKIP (6) to move forward or REPEAT
(4) to move backward.
2. To change the day of the week, re-
peatedly press SKIP(
forward or REPEAT(
backward.
) to move
) to move
4. Press CLOCK (8). The TAD an-
nounces the hour and “AM” or “PM.”
5. To change the hour, repeatedly
press SKIP (6) or REPEAT (4).
3. Press CLOCK. The TAD announces
the hour and “AM” or “PM.”
6. Press CLOCK (8). The TAD an-
nounces the minutes.
4. To change the hour, repeatedly
press SKIP(
) or REPEAT(
).
7. To change the minutes, repeatedly
press SKIP (6) or REPEAT (4).
5. Press CLOCK. The TAD announces
the minutes.
8. When you finish, press CLOCK (8).
The TAD announces the day and
time and beeps twice.
6. To change the minutes, repeatedly
press SKIP(
) or REPEAT(
).
9. Press REMOTE. The REMOTE indi-
7. When you finish, press CLOCK. The
cator turns off.
TAD announces the day and time.
13
Download from Www.Somanuals.com. All Manuals Search And Download.
43-733.fm Page 14 Friday, September 17, 1999 8:57 AM
TELEPHONE OPERATION
and down the four settings and remains
set for subsequent calls.
MAKING AND RECEIVING
A CALL
To make a call, lift the handset and press
TALK. When you hear the dial tone, dial
the desired phone number or memory
number (see “Memory Dialing” on
Page 16).
Note: The TAD-733 beeps three times
when it reaches the highest or lowest
volume setting.
To answer a call if the handset is on the
base, lift the handset and begin your
conversation. If the handset is away
from the base, press any key on the
handset before speaking. The TALK in-
dicator on the handset and the IN USE
indicator on the base flashes.
USING REDIAL
You can quickly redial the last number di-
aled. Lift the handset and press TALK.
When you hear the dial tone, press REDI-
AL.
TALK Indicator
To end a call, press TALK on the handset
or place the handset on the base. The
TALK and the IN USE indicators turn off.
Notes:
• The TAD’s redial memory stores
up to 32 digits, so you can redial
long-distance as well as local
numbers.
Note: If you press TALK to hang up and
the phone does not disconnect, place
the handset on the base.
• The redial memory stores pause en-
tries (see “Entering a Pause” on
Page 17).
SETTING THE HANDSET’S
VOLUME
• The redial memory does not store a
flash entry or any digits entered af-
ter you press FLASH (see “Using
Flash” on Page 15).
You can change the handset’s volume
during a call by repeatedly pressing
VOLUME
or . The volume steps up
14
Download from Www.Somanuals.com. All Manuals Search And Download.
43-733.fm Page 15 Friday, September 17, 1999 8:57 AM
USING FLASH
USING TONE SERVICES
ON A PULSE LINE
FLASH performs the electronic equiva-
lent of a switchhook operation for special
services, such as Call Waiting.
Some special services, such as bank-by-
phone, require tone signals. If you have
pulse service, you can still use these
special tone services by following these
steps.
1. Be sure T/P is set to P.
2. Lift the handset and press TALK.
3. Dial the service’s main number.
For example, if you have Call Waiting,
press FLASH to answer an incoming call
without disconnecting the current call.
Press FLASH again to return to the first
call.
4. When the service answers, press
.
Any additional numbers you dial are
sent as tone signals.
Note: If you do not have any special
phone services, pressing FLASH might
disconnect the current call.
5. After you complete the call, return
the handset to the base or press
TALK on the handset. The phone
automatically resets to pulse dialing.
USING MUTE
The MUTE button on the handset lets
you talk to someone else in the room
without the person on the other end of
the phone line hearing your conversa-
tion. Press MUTE during the call. The
LOW BATT indicator on the handset
lights.
Press MUTE again to resume your
phone conversation.
15
Download from Www.Somanuals.com. All Manuals Search And Download.
43-733.fm Page 16 Friday, September 17, 1999 8:57 AM
USING PAGE
To page the person with the handset or
to find the handset, press PAGE on the
base. The handset beeps twice for about
15 seconds.
2. Enter the number and any tone or
pause entries (see “Using Tone Ser-
vices on a Pulse Line” on Page 15
and “Entering
Page 17).
a
Pause” on
Notes:
• Each tone or pause entry uses
one digit of memory.
To stop the handset from beeping be-
fore it automatically stops, press TALK
twice or press PAGE.
• If you wait more than 30 seconds
to press a key or enter more than
16 digits, the phone sounds one
long beep. Start over at Step 1.
Note: Paging does not work during a
• To keep your accounts secure,
we recommend you do not store
your personal access code for
services such as bank-by-phone
in a memory location.
call.
MEMORY DIALING
You can store up to 20 phone numbers
in memory, then dial a stored number by
pressing a two-digit memory location
number.
3. Press MEM, then enter a memory lo-
cation number (01–20).
A
tone
sounds to indicate that the number
is stored.
Each stored number can be up to 16
digits long, including tone and pause en-
tries.
To replace a stored number, store a new
one in its place.
To clear a memory location (leaving it
empty), press MEM twice, then press the
memory location number you want to
clear (01–20).
Storing a Number in Memory
1. Press MEM on the handset. The
TALK indicator flashes.
16
Download from Www.Somanuals.com. All Manuals Search And Download.
43-733.fm Page 17 Friday, September 17, 1999 8:57 AM
Entering a Pause
Testing Stored Emergency
Numbers
In some telephone systems, you must
dial an access code (9, for example) and
wait for a second dial tone before you
can dial an outside number. You can
store the access code with the phone
number. However, you should also store
a pause after the access code to allow
the outside line time to connect. To do
so, press REDIAL to enter a 2-second
pause after entering the access code.
For a longer pause, press REDIAL again.
If you store an emergency service’s
number (police department, fire depart-
ment, ambulance) and you choose to
test the stored number, make the test
call during the late evening or early
morning hours to avoid peak demand
periods. Also, remain on the line to ex-
plain the reason for your call.
USING AN OPTIONAL
HEADSET
Dialing a Stored Number
To dial a stored number, lift the handset
and press TALK. When you hear the dial
tone, press MEM, then enter the memory
location number (01–20) for the stored
number.
Your TAD-733’s handset is equipped
with a headset jack on top. This jack al-
lows you to connect a headset (not sup-
plied) for handsfree conversation. The
belt clip on the back of the handset lets
you carry the handset everywhere. A va-
riety of headsets are available at your lo-
cal RadioShack store.
Chain-Dialing Service Numbers
For quick recall of numbers for special
services (such as alternate long dis-
tance or bank by phone), store each
group of numbers in its own memory lo-
cation.
Follow these steps to use a headset.
3
1. Insert the headset’s /32 inch (2.5
mm) plug into the
of the handset.
jack on the top
When calling special services, dial the
service’s main number first. Then, at the
appropriate place in the call, press MEM,
then enter the memory location number
for the additional stored numbers.
17
Download from Www.Somanuals.com. All Manuals Search And Download.
43-733.fm Page 18 Friday, September 17, 1999 8:57 AM
2. Place the headset on your head with
the earpiece over either ear and ad-
just the microphone boom until it is
about even with your chin.
To replace the belt clip, insert either tab
of the belt clip into one slot of the hand-
set, then snap the other tab into the other
slot of the handset.
3. Hang the belt clip on your belt.
4. Use the handset to make or receive
calls.
Notes:
• Connecting a headset disconnects
the handset’s earpiece and micro-
phone.
• If you place the handset on the base
to recharge it while the headset is
connected, be sure the handset
seats properly.
REMOVING THE BELT
CLIP
The belt clip on the back of the handset
lets you hang the handset on the belt for
easy portability.
Insert a flat-blade screwdriver into either
side of the belt clip, then pull it off.
18
Download from Www.Somanuals.com. All Manuals Search And Download.
43-733.fm Page 19 Friday, September 17, 1999 8:57 AM
TAD OPERATION
SETTING THE TAD TO
ANSWER CALLS
USING THE MAILBOXES
The TAD-733 has a general message
center and two user mailboxes. It is pre-
set to record messages in the message
center, but a caller can record a mes-
sage for mailbox 1 or 2 by pressing #
then the desired mailbox number within
6 seconds. If the caller presses # then 1
or 2 after the outgoing message plays
for more than 6 seconds, the TAD-733
records the message into both the mes-
sage center and the selected mailbox.
The TAD-733 is ready to answer and
record calls with the prerecorded outgo-
ing message as soon as you connect it
to AC power. To record your own outgo-
ing message, see “Recording an Outgo-
ing Message.”
To turn off the TAD so it does not an-
swer calls, press ANSWER on the base,
or press REMOTE, CHANGE (#) then AN-
SWER ( ) on the handset. The TAD an-
nounces “Answer off” and the message
counter display clears.
Be sure your outgoing message tells the
caller how to record a message for the
desired mailbox.
RECORDING AN
OUTGOING MESSAGE
The TAD-733’s lets you record two sep-
arate messages of up to 60 seconds
each, and it operates differently based
on which mode you select.
To turn on the TAD, press ANSWER on
the base, or press REMOTE, CHANGE (#)
then ANSWER ( ) on the handset. The
TAD announces “Answer on” and the
message counter shows the number of
recorded messages.
• Answer-On — The TAD 733’s prere-
corded outgoing message says,
“Hello, please leave a message af-
ter the tone.” You can also record
your own outgoing message for the
caller to hear when the TAD an-
swers a call.
To set the TAD to play an announce-
ment, press ANSWER on the base again,
or press REMOTE, CHANGE (#) then AN-
SWER ( ) on the handset. The TAD an-
nounces “Announce Only” and the
message counter shows AO.
• Announce-Only — The TAD plays
your outgoing message, but does
not record a message.
If you set the TAD to announce-only,
be sure to state that the caller can-
not leave a message.
19
Download from Www.Somanuals.com. All Manuals Search And Download.
43-733.fm Page 20 Friday, September 17, 1999 8:57 AM
Note: FL flashes when the TAD’s mem-
ory is full. You must delete some mes-
sages before you can record a new
outgoing message.
press REMOTE then ANNC (0) on the
handset, or press ANNC on the base. PL
appears while the message plays.
1. Set the TAD to Answer-On to record
a new outgoing message, or An-
nounce-Only to record the an-
nouncement-only message. See
“Setting the TAD to Answer Calls”
on Page 19.
DELETING AN OUTGOING
MESSAGE
Select the outgoing message you want
to delete. Press DELETE then ANNC on
the base, or REMOTE, DELETE (9), then
ANNC (0) on the handset.
2. Press REMOTE on the handset. The
REMOTE indicator lights and – –
appears on the base.
3. Press CHANGE ( ) then ANNC (0).
SCREENING CALLS
The handset beeps once.
You can let the TAD answer calls for you
then listen to the caller’s message
through the base’s speaker. If you de-
cide to answer the call, lift the handset
then press TALK. If the handset is off the
base, press TALK or pick up any phone
on the same phone line. The TAD stops
recording and resets to answer the next
call.
4. Speak your message in a normal
voice, as though you were talking to
someone on the phone.
Note: If you answer a call just as the
TAD answers, the TAD might not stop
playing the outgoing message. If this
happens, press TALK (or the switchhook
of the extension phone you are using) to
stop the TAD.
5. Press STOP (5) when you finish the
message. The TAD plays back the
outgoing message, then beeps
twice.
You can also use the handset to screen
calls. When the TAD answers a call,
press REMOTE and listen to caller’s
message. If you decide to answer the
call, press TALK. If you decide to let the
TAD continue to record the message,
press REMOTE again.
6. Press REMOTE. The REMOTE indi-
cator turns off.
To play the outgoing message at any
time, select the desired mode, then
20
Download from Www.Somanuals.com. All Manuals Search And Download.
43-733.fm Page 21 Friday, September 17, 1999 8:57 AM
• you pick up the TAD-733’s handset
or any phone on the same phone
line
ADJUSTING THE TAD’S
VOLUME
To adjust the TAD’s volume, repeatedly
press VOLUME
handset.
or
on the base or
RECORDING A MEMO
A memo is a message you can record
using the handset for yourself or others
in your home or office. You can record a
memo of up to 60 seconds long in either
mailbox or the message center.
The base has eight volume levels. The
handset has four.
Note: The base sounds a long beep
when it reaches the highest volume set-
ting.
The TAD-733 stores memos as incom-
ing messages (see “Playing Messages”
on Page 22).
RECORDING INCOMING
MESSAGES
1. Press REMOTE. The REMOTE indi-
cator lights.
2. Press CHANGE (#) on the handset
then press M-BOX 1 (1), M-BOX 2 (2),
or M-CENTER (3).
After the TAD answers a call, it plays the
outgoing message, beeps, and then the
caller can select a mailbox by entering #
then 1, or # then 2 within 6 seconds. If
the caller does not select a mailbox, the
TAD records the message in the mes-
sage center.
Each incoming message can be up to
60 seconds long. (The maximum record-
ing capacity is 12 minutes or 62 record-
ed messages.)
3. Speak your message into the hand-
set.
4. When you finish recording the
The TAD hangs up and resets to answer
the next call when:
memo, press STOP (5).
5. Press REMOTE. The REMOTE indi-
• the caller hangs up
cator turns off.
• the maximum message length (60
seconds) is reached
• the TAD hears a busy signal or more
than 7 seconds of silence
21
Download from Www.Somanuals.com. All Manuals Search And Download.
43-733.fm Page 22 Friday, September 17, 1999 8:57 AM
• When you play back messages us-
ing the handset, the message num-
ber does not appear on the display.
PLAYING MESSAGES
After a new message is recorded, the
TAD’s message counter window shows
the total number of messages stored,
and the REMOTE indicator on the hand-
set flashes. The message counter dis-
play flashes if there are new messages
in the message center. If new messages
have been recorded in a user mailbox,
the indicator for that mailbox flashes.
The message counter display and mail-
box indicators light steadily if they con-
tain only messages that have been
reviewed.
After all messages play, the TAD says,
“End of messages.”
To skip to the next message, press SKIP
on the base or SKIP (6) on the
handset.
To replay a message, press REPEAT
on the base or REPEAT (4) on the
handset.
To replay the previous message, press
Message Counter
REPEAT
on the base or REPEAT
(4) on the handset while the TAD is an-
nouncing the message number.
To stop playback, press STOP on the
base or STOP (5) on the handset.
If you are using the handset, press RE-
MOTE when you finish reviewing mes-
sages. The TAD resets to answer calls.
Press the desired mailbox or the mes-
sage center button on the base, or press
REMOTE then the desired button on the
handset. The TAD announces the total
number of messages in the selected
mailbox or the message center. Before
playing each message, the TAD tells
you the message’s number and the day
and time the message was recorded. If
no messages are recorded, the TAD
says “You have no message.”
DELETING MESSAGES
To delete the current message during
playback, press DELETE on the base or
DELETE (9) on the handset.
Notes:
• If you did not set the day and time,
the TAD only announces the num-
ber of messages recorded and each
message’s number.
22
Download from Www.Somanuals.com. All Manuals Search And Download.
43-733.fm Page 23 Friday, September 17, 1999 8:57 AM
Note: You can replay a deleted mes-
sage by repeatedly pressing REPEAT on
the base or REPEAT (4) on the handset
before the TAD announces “End of mes-
sages.”
Note: If you do not begin entering
the new code within 20 seconds, the
TAD beeps and stops the process. If
this happens, start over at Step 1.
3. Press REMOTE. The REMOTE indi-
cator turns off.
To delete all played messages from a
mailbox or the message center, press
DELETE then the mailbox or message
center button. The TAD beeps.
To check the remote operation security
code, press REMOTE then CODE. The
TAD announces “Code is xx” and beeps
twice.
Note: You must play a message before
you can delete it.
CHANGING THE REMOTE
OPERATION SECURITY
CODE
To use your TAD from a remote tele-
phone, you must first enter a 2-digit re-
mote operation security code. The
security code for your TAD is preset to
50. You can use the preset code, or fol-
low these steps to change it.
1. Press REMOTE on the handset. The
REMOTE indicator lights.
2. Press CHANGE ( ) then CODE (7).
The TAD announces “Enter new
code.” Enter a new two-digit remote
operation security code. The TAD
announces “New code is xx” and
beeps twice.
23
Download from Www.Somanuals.com. All Manuals Search And Download.
43-733.fm Page 24 Friday, September 17, 1999 8:57 AM
REMOTE OPERATION
While you are away from your home or
office, you can use a touch-tone phone
or a pulse (rotary) phone with a pocket
tone dialer to enter your remote opera-
tion security code and do any of the fol-
lowing:
1. Dial your phone number. After about
10 rings, the TAD automatically
turns on to answer your call and an-
nounces “Answer off.”
2. Enter your remote operation securi-
ty code. The TAD beeps.
• set the TAD to answer calls
• listen to messages
Note: If you do not enter each digit
of the security code within 20 sec-
onds, the TAD hangs up.
• record a new outgoing message
• record a memo
3. Press then . The TAD says “An-
swer on” and beeps twice. It is now
set to record calls.
• delete messages
Note: You cannot operate the TAD from
another phone on the same line as your
TAD-733.
At this point you can hang up or enter
other remote commands.
USING REMOTE
COMMANDS
USING TOLL-SAVER
If the 4/7/TS switch is set to TS (toll-
saver, see “Number of Rings” on
Page 12), the TAD answers after about
two rings if you have new messages. If
there are no new messages, the TAD
waits for about four rings before it an-
swers. This gives you time to hang up
before the TAD answers so you can
avoid unnecessary long-distance charg-
es.
Follow these steps to operate the TAD
from a remote touch-tone phone.
1. Dial your phone number and wait for
the TAD to answer.
2. When the outgoing message be-
gins, enter your 2-digit remote oper-
ation security code. The TAD beeps
twice to let you know you entered
the code correctly.
3. Enter the code for the desired re-
mote command (see “Remote Com-
mands” on Page 25).
USING REMOTE
ANSWER-ON
4. When you finish, hang up.
Follow these steps to remotely set the
TAD to answer calls.
Note: If you wait more than 20 seconds
without entering a command, the TAD
hangs up.
24
Download from Www.Somanuals.com. All Manuals Search And Download.
43-733.fm Page 25 Friday, September 17, 1999 8:57 AM
Remote Commands
Press:
9
To:
Delete the current mes-
sage.
Press:
1
To:
Record a memo to mail-
box 1.
0
Play the outgoing mes-
sage.
2
3
7
Record a memo to mail-
box 2.
Check TAD answer on/off
or announce-only status.
Record a memo to the
message center.
Change the remote oper-
ation security code.
8
0
Set the day and time.
Record a new outgoing
message.
Set TAD answer on/off or
announce-only.
1
2
3
4
5
Play all messages from
mailbox 1.
Play all messages from
mailbox 2.
Play all messages from
the message center.
Replay the current mes-
sage.
Stop playback of mes-
sages, memos, or the
outgoing announcement;
end recording of memo
or outgoing announce-
ment.
6
7
8
Skip forward to the next
message.
Check the remote opera-
tion security code.
Check the day and time.
25
Download from Www.Somanuals.com. All Manuals Search And Download.
43-733.fm Page 26 Friday, September 17, 1999 8:57 AM
TROUBLESHOOTING
We do not expect you to have any problems with your TAD-733, but if you do, the fol-
lowing suggestions might help.
Problem
Suggestion
Noise, static, or weak signal. Move the handset closer to the base or relocate the
base (see “Selecting a Location” on Page 7).
Make sure the base’s antenna is vertically upright
and the handset’s antenna is properly connected.
TAD does not answer calls.
Make sure the TAD is set to answer calls.
Check all phone line connections.
Make sure the AC adapter is properly connected.
TAD does not record callers’ Memory may be full (FL appears). Delete some
messages.
messages.
Turn off the announce-only feature (see “Screening
Calls” on Page 20).
The handset does not ring
when you receive a call.
Make sure the ringer is turned on.
Return the handset to the base for about 5 seconds
to reset the security access-protection code.
Make sure the battery pack is properly connected
and charged.
You hear other calls while us- Try another phone connected to the same line. If
ing your phone.
you still hear other calls, the problem is probably in
your wiring or local service. Contact your local tele-
phone company.
There is no dial tone.
Check all phone line connections.
Make sure the AC adapter is properly connected.
Make sure the battery pack is properly connected
and charged. If the battery pack will not charge, re-
place it (see “Replacing the Battery Pack” on
Page 28).
If you still have problems, disconnect the phone. If other phones on the same line
work properly, the fault is in this phone or its installation. If you cannot find the prob-
lem, take your TAD-733 to your local RadioShack store for assistance.
26
Download from Www.Somanuals.com. All Manuals Search And Download.
43-733.fm Page 27 Friday, September 17, 1999 8:57 AM
CARE AND MAINTENANCE
Your RadioShack TAD-733 900 MHz Cordless Telephone with Digital Answering
System is an example of superior design and craftsmanship. The following sugges-
tions will help you care for your TAD-733 so you can enjoy it for years.
Keep the TAD-733 dry. If it gets wet, wipe it dry immediately. Liquids
might contain minerals that can corrode the electronic circuits.
Use and store the TAD-733 only in normal temperature environments.
Temperature extremes can shorten the life of electronic devices, dam-
age batteries, and distort or melt plastic parts.
Keep the TAD-733 away from dust and dirt, which can cause premature
wear of parts.
Handle the TAD-733 gently and carefully. Dropping it can damage cir-
cuit boards and cases and can cause the TAD-733 to work improperly.
Use only fresh batteries of the required size and recommended type.
Batteries can leak chemicals that damage your TAD-733’s electronic
parts.
Wipe the TAD-733 with a damp cloth occasionally to keep it looking
new. Do not use harsh chemicals, cleaning solvents, or strong deter-
gents to clean the TAD-733.
Modifying or tampering with the TAD-733’s internal components can cause a mal-
function and might invalidate its warranty and void your FCC authorization to oper-
ate it. If your TAD-733 is not performing as it should, take it to your local
RadioShack store for assistance. If the trouble is affecting the telephone lines, the
phone company can ask you to disconnect your TAD-733 until you have resolved
the problem.
27
Download from Www.Somanuals.com. All Manuals Search And Download.
43-733.fm Page 28 Friday, September 17, 1999 8:57 AM
• Do not open or mutilate the battery
pack.
REPLACING THE
BATTERY PACK
• Be careful not to short the battery
pack by touching it with conducting
materials, such as rings, bracelets,
and keys. The battery pack or con-
ductor might overheat and burn.
If you follow the instructions in “Connect-
ing and Charging the Handset Battery
Pack” on Page 9, the battery pack
should last about one year. If the battery
pack does not hold a charge for more
than 2 hours after an overnight charge,
replace it with a 3.6 volt, 600 mAh battery
pack with a connector that fits the socket
in the battery compartment. You can or-
der a replacement through your local Ra-
dioShack store.
If you have trouble replacing the battery
pack, take the phone to your local Ra-
dioShack store for assistance.
Important: This tele-
phone can use nickel
cadmium rechargeable
batteries. At the end of a
nickel cadmium battery's
useful life, it must be re-
Install the new battery pack as follows,
then charge the battery for about 15
hours.
0
0
8
3
4
cycled or disposed of properly. Contact
your local, county, or state hazardous
waste management authorities for infor-
mation on recycling or disposal pro-
grams in your area or call 1-800-843-
7422. Some options that might be avail-
able are: municipal curbside collection,
drop-off boxes at retailers such as your
local RadioShack store, recycling collec-
tion centers, and mail-back programs.
Note: To avoid losing information stored
in memory, try to install and begin charg-
ing the new battery pack within 25 sec-
onds.
1. Press down and slide off the battery
compartment cover.
2. Remove the battery pack then gen-
tly pull on the battery pack connec-
tor to disconnect it.
3. Plug the new battery pack’s connec-
tor into the socket and place the bat-
tery pack into the compartment.
4. Replace the cover.
Cautions:
• You must use a replacement battery
pack of the same size and type, with
the proper connector.
• Do not dispose of the battery pack in
a fire because it might explode.
28
Download from Www.Somanuals.com. All Manuals Search And Download.
43-733.fm Page 29 Friday, September 17, 1999 8:57 AM
If you cannot eliminate the interference,
the FCC requires that you stop using
your phone.
THE FCC WANTS YOU TO
KNOW
In the unlikely event that your phone
causes problems on the phone line, the
phone company can temporarily discon-
tinue your service. The phone company
normally attempts to notify you in ad-
vance. If advance notice is not practical,
the phone company notifies you as soon
as possible and advises you of your
right to file a complaint with the FCC.
Some cordless telephones operate on
frequencies that may cause interference
to nearby TVs and VCRs. To minimize or
prevent such interference, the base of
the cordless telephone should not be
placed near or on top of a TV or VCR.
LIGHTNING
Also, the phone company can make
changes to its lines, equipment, opera-
tions, or procedures that could affect the
operation of this telephone. The tele-
phone company notifies you of these
changes in advance, so you can take the
necessary steps to prevent interruption
of your telephone service.
Your telephone has built-in lightning pro-
tection to reduce the risk of damage
from surges in phone and power line
current. This protection meets or ex-
ceeds FCC requirements. However,
lightning striking the phone line or power
lines can damage your phone.
Lightning damage is not common. Nev-
ertheless, if you live in an area that has
severe electrical storms, we suggest
that you unplug your phone during
storms to reduce the possibility of dam-
age.
Your phone might cause TV or radio in-
terference even when it is operating
properly. To determine whether your
phone is causing the interference, turn
off your phone. If the interference goes
away, your phone is causing the interfer-
ence. Try to eliminate the interference
by:
• Moving your phone away from the
receiver
• Connecting your phone to an AC
outlet that is on a different electrical
circuit from the receiver
• Contacting your local RadioShack
store for help
29
Download from Www.Somanuals.com. All Manuals Search And Download.
43-733.fm Page 30 Friday, September 17, 1999 8:57 AM
NOTES
30
Download from Www.Somanuals.com. All Manuals Search And Download.
43-733.fm Page 31 Friday, September 17, 1999 8:57 AM
31
Download from Www.Somanuals.com. All Manuals Search And Download.
43-733.fm Page 32 Friday, September 17, 1999 8:57 AM
Limited One-Year Warranty
This product is warranted by RadioShack against manufacturing defects in material and workman-
ship under normal use for one (1) year from the date of purchase from RadioShack company-owned
stores and authorized RadioShack franchisees and dealers. EXCEPT AS PROVIDED HEREIN, Ra-
dioShack MAKES NO EXPRESS WARRANTIES AND ANY IMPLIED WARRANTIES, INCLUDING
THOSE OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE, ARE LIMITED
IN DURATION TO THE DURATION OF THE WRITTEN LIMITED WARRANTIES CONTAINED
HEREIN. EXCEPT AS PROVIDED HEREIN, RadioShack SHALL HAVE NO LIABILITY OR RE-
SPONSIBILITY TO CUSTOMER OR ANY OTHER PERSON OR ENTITY WITH RESPECT TO ANY
LIABILITY, LOSS OR DAMAGE CAUSED DIRECTLY OR INDIRECTLY BY USE OR PERFOR-
MANCE OF THE PRODUCT OR ARISING OUT OF ANY BREACH OF THIS WARRANTY, IN-
CLUDING, BUT NOT LIMITED TO, ANY DAMAGES RESULTING FROM INCONVENIENCE, LOSS
OF TIME, DATA, PROPERTY, REVENUE, OR PROFIT OR ANY INDIRECT, SPECIAL, INCIDEN-
TAL, OR CONSEQUENTIAL DAMAGES, EVEN IF RadioShack HAS BEEN ADVISED OF THE
POSSIBILITY OF SUCH DAMAGES.
Some states do not allow the limitations on how long an implied warranty lasts or the exclusion of in-
cidental or consequential damages, so the above limitations or exclusions may not apply to you.
In the event of a product defect during the warranty period, take the product and the RadioShack
sales receipt as proof of purchase date to any RadioShack store. RadioShack will, at its option, un-
less otherwise provided by law: (a) correct the defect by product repair without charge for parts and
labor; (b) replace the product with one of the same or similar design; or (c) refund the purchase
price. All replaced parts and products, and products on which a refund is made, become the prop-
erty of RadioShack. New or reconditioned parts and products may be used in the performance of
warranty service. Repaired or replaced parts and products are warranted for the remainder of the
original warranty period. You will be charged for repair or replacement of the product made after the
expiration of the warranty period.
This warranty does not cover: (a) damage or failure caused by or attributable to acts of God, abuse,
accident, misuse, improper or abnormal usage, failure to follow instructions, improper installation or
maintenance, alteration, lightning or other incidence of excess voltage or current; (b) any repairs
other than those provided by a RadioShack Authorized Service Facility; (c) consumables such as
fuses or batteries; (d) cosmetic damage; (e) transportation, shipping or insurance costs; or (f) costs
of product removal, installation, set-up service adjustment or reinstallation.
This warranty gives you specific legal rights, and you may also have other rights which vary from
state to state.
RadioShack Customer Relations, 200 Taylor Street, 6th Floor, Fort Worth, TX 76102
We Service What We Sell
04/99
RadioShack
A Division of Tandy Corporation
Fort Worth, Texas 76102
09A99
Printed in China
Download from Www.Somanuals.com. All Manuals Search And Download.
|