Radio Shack Cordless Telephone ET 548 User Guide

43-1048.fm Page 1 Tuesday, August 17, 1999 12:45 PM  
Cat. No. 43-1048  
OWNER’S MANUAL  
Please read before using this equipment.  
ET-548  
25-Channel Cordless  
Headset Telephone  
Download from Www.Somanuals.com. All Manuals Search And Download.  
43-1048.fm Page 3 Tuesday, August 17, 1999 12:45 PM  
This phone has been tested and found to  
comply with all applicable UL and FCC  
standards.  
Warning: To prevent fire or shock  
hazard, do not expose this product  
to rain or moisture.  
Important Note: Cordless phones such  
as this one require AC power to operate.  
When the AC power is off, you cannot dial  
out or receive incoming calls using your  
ET-548. To be safe, you should also have  
a phone that does not need AC power to  
operate (not a cordless phone) so you  
can still make and receive calls if there is  
an AC power failure.  
CAUTION  
RISK OF ELECTRIC SHOCK.  
!
DO NOT OPEN.  
CAUTION: TO REDUCE THE RISK OF  
ELECTRIC SHOCK, DO NOT REMOVE  
COVER OR BACK. NO USER-SERVICE-  
ABLE PARTS INSIDE. REFER SERVIC-  
ING TO QUALIFIED PERSONNEL.  
This symbol is intended to alert you to  
the presence of uninsulated dangerous  
voltage within the product’s enclosure  
that might be of sufficient magnitude to  
constitute a risk of electric shock. Do not  
open the product’s case.  
Note: Your phone operates on standard  
radio frequencies as allocated by the  
FCC. It is possible for other radio units  
operating nearby on similar frequencies  
to unintentionally intercept your conversa-  
tion or cause interference. This possible  
lack of privacy can occur with any cord-  
less phone.  
This symbol is intended to inform you  
that important operating and mainte-  
nance instructions are included in the lit-  
erature accompanying this product.  
!
We recommend you record your phone’s  
serial number here. The number is on the  
bottom of the base.  
The supplied adapter is a Class 2 120V  
AC/12V DC adapter that delivers at least  
200 milliamps with its center tip set to  
positive.  
Serial Number: __________________  
3
Download from Www.Somanuals.com. All Manuals Search And Download.  
43-1048.fm Page 4 Tuesday, August 17, 1999 12:45 PM  
READ THIS BEFORE  
INSTALLATION  
FCC STATEMENT  
This telephone complies with Part 68 of  
FCC Rules. You must, upon request, pro-  
vide the FCC Registration Number and  
the REN to your phone company. These  
numbers are shown on the bottom of the  
base.  
We have designed your phone to conform  
to federal regulations, and you can con-  
nect it to most telephone lines. However,  
each device that you connect to the  
phone line draws power from the phone  
line. We refer to this power draw as the  
device’s ringer equivalence number, or  
REN. The REN is on the bottom of the  
base.  
Note: You must not connect your phone  
to any of the following:  
• coin-operated systems  
• party-line systems  
If you are using more than one phone or  
other device on the line, add up all the  
RENs. If the total is more than five, your  
phones might not ring. In rural areas, a to-  
tal REN of three might impair ringer oper-  
ation. If ringer operation is impaired,  
remove a device from the line.  
• most electronic key phone systems  
4
Download from Www.Somanuals.com. All Manuals Search And Download.  
43-1048.fm Page 5 Tuesday, August 17, 1999 12:45 PM  
CONTENTS  
Installation .................................................................................................................... 6  
Selecting a Location ................................................................................................ 6  
Connecting the Phone ............................................................................................. 6  
Connecting and Charging the Battery Pack ............................................................ 7  
Attaching the Headset Holder ................................................................................. 9  
Adjusting the Headset ............................................................................................. 9  
Setting the Dialing Mode ....................................................................................... 10  
Using the Belt Clip ................................................................................................. 10  
Operation .................................................................................................................... 11  
Making and Receiving Calls .................................................................................. 11  
Changing Channels ............................................................................................... 12  
Setting the Volume ................................................................................................ 12  
Using Redial .......................................................................................................... 12  
Using Privacy ........................................................................................................ 13  
Using Flash ........................................................................................................... 13  
Using Tone Services on a Pulse Line .................................................................... 13  
Memory Dialing ..................................................................................................... 14  
Storing a Number in Memory .......................................................................... 14  
Entering a Pause in a Memory Number .......................................................... 15  
Dialing a Stored Number ................................................................................ 15  
Chain Dialing Service Numbers ...................................................................... 15  
Testing Stored Emergency Numbers .............................................................. 15  
Troubleshooting ......................................................................................................... 16  
Care and Maintenance ............................................................................................... 18  
Replacing the Battery Pack ................................................................................... 19  
The FCC Wants You to Know ................................................................................ 20  
Lightning ................................................................................................................ 21  
5
Download from Www.Somanuals.com. All Manuals Search And Download.  
43-1048.fm Page 6 Tuesday, August 17, 1999 12:45 PM  
INSTALLATION  
Caution: The supplied adapter is a Class  
2 120V AC/12V DC adapter that delivers  
at least 200 milliamps with its center tip  
set to positive. Its plug correctly fits the  
phone’s DC 12V jack. Using an adapter  
that does not meet these requirements  
could damage the phone or the adapter.  
SELECTING A LOCATION  
You can place the phone’s base on a  
desktop, shelf, or table. Select a location  
that is:  
• near an AC outlet  
• near a telephone line jack  
• out of the way of normal activities  
CONNECTING THE PHONE  
• away from electrical machinery, elec-  
trical appliances, metal walls, filing  
cabinets, wireless intercoms, secu-  
rity alarms, and room monitors  
After you select a location for the phone’s  
base, follow these steps to connect it to  
AC power and to the phone line.  
The base’s location affects the phone’s  
range. If you have a choice of several lo-  
cations, try each to see which provides  
the best performance.  
Illustration  
Your telephone connects directly to a  
modular telephone line jack. If your tele-  
phone wiring does not have a modular  
jack, you can update the wiring yourself  
or have the telephone company update it  
for you.  
Notes:  
• RadioShack stores sell jacks and  
adapters to convert older wiring meth-  
ods to modular wiring.  
1. Plug one end of the supplied modular  
cord into the TEL. LINE jack on the  
back of the base.  
• The USOC number of the jack to be  
installed is RJ11C.  
2. Plug the modular cord’s other end  
into a modular phone line jack.  
6
Download from Www.Somanuals.com. All Manuals Search And Download.  
43-1048.fm Page 7 Tuesday, August 17, 1999 12:45 PM  
3. Plug the supplied AC adapter’s barrel  
plug into the DC 12V jack on the back  
of the base.  
2. Slide the battery pack’s connector  
onto the connector pins inside the  
battery compartment.  
4. Plug the adapter into a standard AC  
outlet. The IN USE/CHARGE indica-  
tor lights when the keypad is on the  
base.  
Illustration  
5. Lift the base’s antenna to a vertical  
position.  
3. Replace the cover and secure it with  
the screw.  
CONNECTING AND  
CHARGING THE BATTERY  
PACK  
4. To charge the battery pack, place the  
remote keypad on the base. The IN  
USE/CHARGE indicator on the base  
lights.  
The ET-548 comes with a rechargeable  
nickel-cadmium battery pack in the re-  
mote keypad. You must connect and then  
charge the battery pack for at least 15  
hours before you use it the first time.  
Illustration  
1. Use a Phillips screwdriver to remove  
the screw that secures the battery  
compartment cover, then remove the  
cover.  
Illustration  
7
Download from Www.Somanuals.com. All Manuals Search And Download.  
43-1048.fm Page 8 Tuesday, August 17, 1999 12:45 PM  
Recharge the battery pack when the  
TALK/LOW BATT. indicator lights.  
• If the IN USE/CHARGE indicator  
does not light when you place the re-  
mote keypad on the base, be sure the  
battery pack and AC adapter are cor-  
rectly and securely connected. Also,  
check the charging contacts on the  
remote keypad and base. If the con-  
tacts are dirty or tranished, clean  
them with a pencil eraser.  
Illustration  
Notes:  
Illustration  
• When you first use the phone after  
charging or recharging the battery  
pack, the phone might not work and  
you might hear error tones. (You do  
POWER  
not hear the error tones if  
OFF  
is  
set to  
.)  
If you hear the error tones, return the  
remote keypad to the cradle for at  
least 5 seconds to reset the security  
access-protection code.  
• About once a month, fully discharge  
the battery pack by keeping the  
phone off the base until the TALK/  
LOW BATT. indicator lights. Other-  
wise, the battery pack loses its ability  
to fully recharge.  
POWER  
• If battery power is low,  
is set  
• If you are not going to use your phone  
for an extended period of time, dis-  
connect its battery. This helps to in-  
crease the battery’s usable life.  
ON  
to  
, and the headset is not in use,  
the TALK/LOW BATT. indicator slowly  
flashes. If battery power is too low,  
the indicator does not light.  
8
Download from Www.Somanuals.com. All Manuals Search And Download.  
43-1048.fm Page 9 Tuesday, August 17, 1999 12:45 PM  
slightly to tighten it. If the headset is  
tight, gently pull the headset band out  
to loosen it.  
ATTACHING THE HEADSET  
HOLDER  
Put the headset holder into the slot on the  
back of the base and slide it into place.  
2. Hold the headset in place, and turn  
the microphone boom until it is about  
2 inches from your mouth.  
Illustration  
Illustration  
When you are not using the headset,  
place it on the headset holder.  
ADJUSTING THE HEADSET  
Illustration  
1. Put on the headset, and adjust the  
band until it rests with almost no pres-  
sure on your ear and the top of your  
head.  
Illustration  
If the headset is loose, remove it and  
gently push the headset band inward  
9
Download from Www.Somanuals.com. All Manuals Search And Download.  
43-1048.fm Page 10 Tuesday, August 17, 1999 12:45 PM  
SETTING THE DIALING  
MODE  
USING THE BELT CLIP  
Use the belt clip to hang the remote key-  
pad on your belt or waistband for hands-  
free carrying.  
Illustration  
Illustration  
TONE-PULSE  
Set  
on the side of the base  
for the type of service you have. If you are  
not sure which type you have, do this sim-  
ple test after charging the battery.  
POWER  
ON  
1. Set  
2. Set  
to  
.
TONE-PULSE  
TONE  
to  
.
3. Lift the remote keypad from the base.  
TALK/HANG UP  
Then press  
for a dial tone.  
and listen  
4. Press any number other than 0.  
If the dial tone stops, you have touch-  
TONE-PULSE  
tone service. Leave  
TONE  
set  
to  
.
If the dial tone continues, you have  
TONE-PULSE  
pulse service. Set  
PULSE  
to  
.
10  
Download from Www.Somanuals.com. All Manuals Search And Download.  
43-1048.fm Page 11 Tuesday, August 17, 1999 12:45 PM  
OPERATION  
Notes:  
To conserve battery power, set  
MAKING AND RECEIVING  
CALLS  
POWER to OFF when the remote key-  
pad is away from the base. When you  
hear another phone on the same line  
ring, set POWER to ON and press  
TALK/HANG UP to answer the call.  
Before using the phone, put the headset  
on and adjust it as needed. Then set  
POWER to ON.  
To make a call, press TALK/HANG UP.  
You hear a dial tone and the TALK/LOW  
BATT. indicator lights. Dial the number  
you want to call.  
• When you press a button, a single  
tone indicates that the phone accepts  
the command. Three tones indicate  
that you pressed a button in error, you  
are out of range, or there is too much  
interference. If there is severe inter-  
ference, move the remote keypad  
closer to the base before you press  
any key.  
Illustration  
• If interference is severe, the remote  
keypad might lose communication  
with the base and the call might dis-  
connect. This does not happen often,  
but if it does, return the remote key-  
pad to the cradle for a few seconds.  
To disconnect a call, press TALK/HANG  
UP or place the keypad on the base.  
To answer a call when the keypad is on  
the base, pick up the keypad. The TALK/  
LOW BATT. indicator lights.  
To answer a call when the keypad is not  
on the base, press TALK/HANG UP. The  
TALK/LOW BATT. indicator lights.  
11  
Download from Www.Somanuals.com. All Manuals Search And Download.  
43-1048.fm Page 12 Tuesday, August 17, 1999 12:45 PM  
CHANGING CHANNELS  
USING REDIAL  
Your headset cordless telephone has an  
Auto Scan feature that automatically se-  
lects a clear channel when you press  
To quickly redial the last number dialed,  
TALK/HANG UP  
REDIAL/  
press  
then  
PAUSE  
.
TALK/HANG UP  
. If you experience inter-  
CHANNEL  
ference during a call, press  
to  
switch to another channel until you have  
good reception.  
Illustration  
Illustration  
Notes:  
• The redial memory holds up to 80 dig-  
its in the tone mode and 79 digits in  
the pulse mode, so you can redial  
long-distance as well as local num-  
bers.  
SETTING THE VOLUME  
• The redial memory can also switch  
from pulse to tone dialing (see “Using  
Tone Services on a Pulse Line” on  
VOLUME  
The  
control lets you adjust the  
volume you hear through the headset.  
This is especially useful for people who  
have trouble hearing, or when you en-  
counter poor phone lines or are in an es-  
pecially noisy area like a kitchen or  
PAUSE  
Page 13) and can store  
en-  
tries (see “Entering a Pause in a  
Memory Number” on Page 15).  
VOLUME  
workshop. Simply set  
sired listening level.  
to the de-  
Illustration  
12  
Download from Www.Somanuals.com. All Manuals Search And Download.  
43-1048.fm Page 13 Tuesday, August 17, 1999 12:45 PM  
Notes:  
• The redial memory does not store the  
USING PRIVACY  
PRIVACY  
Hold down  
to talk to someone  
FLASH  
entry or the digits you press  
.
else in the room without the person on the  
other end of the phone line hearing your  
conversation. You can still hear the per-  
son on the other end of the phone line.  
FLASH  
after  
• If you do not have any special phone  
FLASH  
services, pressing  
connect your current call.  
might dis-  
Illustration  
USING TONE SERVICES ON  
A PULSE LINE  
Some special phone services, such as  
bank-by-phone, require tone signals. If  
you have pulse service, you can still use  
these special tone services.  
PRIVACY  
Release  
to resume your phone  
conversation.  
USING FLASH  
1. Dial the service’s main number.  
TONE/  
2. Press  
at the point where  
tone signals are required, then dial  
the additional numbers. The phone  
sends these numbers as tone signals.  
Illustration  
3. The phone automatically resets to the  
pulse mode when you hang up.  
FLASH  
provides the electronic equivalent  
of a switchhook signal for special phone  
services such as Call Waiting.  
For example, if you have Call Waiting,  
you can put your current call on hold and  
FLASH  
answer a second call by pressing  
FLASH  
.
Press  
the two calls.  
again to alternate between  
13  
Download from Www.Somanuals.com. All Manuals Search And Download.  
43-1048.fm Page 14 Tuesday, August 17, 1999 12:45 PM  
exits the number storing process.  
Start again from Step 1.  
MEMORY DIALING  
You can store up to 10 numbers of up to  
16 digits.  
2. Dial the number you want to store.  
MEMORY  
3. Press  
again.  
Notes:  
4. Press the memory location number  
(0–9) where you want to store the  
number. A long beep sounds, and the  
phone number is stored in memory.  
To keep your accounts secure, we  
recommend you do not store your  
personal access code for services  
such as bank-by-phone in a memory  
location.  
5. Pull out the memory index card at the  
bottom of the base and write the  
stored number next to the memory  
location number. We recommend you  
use a pencil in case you want to  
change it later.  
• When storing numbers for special  
services (such as alternate long dis-  
tance or bank-by-phone), store the  
service’s main phone number in one  
memory location and numbers for ad-  
ditional information in other locations.  
Illustration  
Storing a Number in Memory  
1. With the TALK/LOW BATT. indicator  
MEMORY  
off, press  
.
Illustration  
Notes:  
• If you receive a call while you are  
storing a number in memory, press  
Note: If you do not press any button  
on the keypad within about 10 sec-  
onds, a buzz sounds and the phone  
TALK/HANG UP  
to answer the call. Af-  
ter the call, begin again at Step 1.  
14  
Download from Www.Somanuals.com. All Manuals Search And Download.  
43-1048.fm Page 15 Tuesday, August 17, 1999 12:45 PM  
To change a number stored in mem-  
ory, simply store a new number in that  
memory location.  
Dialing a Stored Number  
Press TALK/HANG UP, and when you hear  
a dial tone, press MEMORY then the mem-  
ory location number. The phone dials the  
stored number.  
To clear a memory location so no  
number is stored there, press MEM-  
ORY twice, then press the memory lo-  
cation number. A long beep sounds,  
and the number is cleared from mem-  
ory.  
Chain Dialing Service Numbers  
Note: If you use pulse dialing to dial the  
service, be sure you have stored a tone  
entry (TONE/ ) in another memory loca-  
tion.  
If a buzz sounds, you did not suc-  
cessfully clear the memory location.  
Repeat the process.  
When you hear a dial tone, press MEMO-  
RY and the memory location number for  
the service’s main number. When the ser-  
vice’s main number answers, press MEM-  
ORY and the memory location numbers  
for the additional information.  
Entering a Pause in a Memory  
Number  
In some telephone systems, you must dial  
an access code (9, for example) and wait  
for a second dial tone before you can dial  
an outside number. To enter a 2-second  
pause, press REDIAL/PAUSE at the appro-  
priate point when you store a number. To  
enter another 2-second pause, press RE-  
DIAL/PAUSE again.  
Testing Stored Emergency  
Numbers  
If you store an emergency service’s num-  
ber (police department, fire department,  
ambulance) and you want to test the  
stored number, make the test call during  
the late evening or early morning to avoid  
peak demand periods. Remain on the line  
to explain the reason for your call.  
Illustration  
15  
Download from Www.Somanuals.com. All Manuals Search And Download.  
43-1048.fm Page 16 Tuesday, August 17, 1999 12:45 PM  
TROUBLESHOOTING  
We do not expect you to have any problems with your phone, but if you do, the following  
suggestions might help. If you still have problems, take the phone to your local Ra-  
dioShack store for assistance.  
SYMPTOM  
SUGGESTION  
Interference is severe.  
Move the remote keypad closer to the base.  
Keep the base and remote keypad away from interfer-  
ence sources such as computers, radio-controlled toys,  
wireless microphones, wireless alarm systems, wireless  
intercoms and room monitors, fluorescent lights, and  
electrical appliances.  
Turn off the interfering device.  
Hang up and redial the number.  
The range decreases.  
Fully extend the base’s antenna and raise it to a vertical  
position.  
Ensure the antenna is not touching a metal surface.  
Recharge the remote keypad battery pack.  
The volume level drops or Hang up the second phone.  
you hear unusual sounds  
when someone picks up  
another phone on the  
same line.  
16  
Download from Www.Somanuals.com. All Manuals Search And Download.  
43-1048.fm Page 17 Tuesday, August 17, 1999 12:45 PM  
SYMPTOM  
SUGGESTION  
The phone does not work. Ensure POWER is set to ON.  
Move the remote keypad closer to the base.  
Fully extend the base’s antenna and raise it to a vertical  
position.  
Ensure the phone’s modular cord and the AC adapter  
are correctly and securely connected.  
Recharge the remote keypad’s battery pack. (If the bat-  
tery power is too low, the TALK/LOW BATT. indicator  
does not light.)  
Reset the security access-protection code by placing  
the remote keypad in the cradle with POWER set to ON,  
disconnect AC power and then reconnect AC power.  
If the problem persists, disconnect the phone. If other phones on the same line work  
properly, the fault is in this phone or its installation. If you cannot locate the problem,  
take your phone to your local RadioShack store for assistance.  
17  
Download from Www.Somanuals.com. All Manuals Search And Download.  
43-1048.fm Page 18 Tuesday, August 17, 1999 12:45 PM  
CARE AND MAINTENANCE  
Your RadioShack ET-548 25-Channel Cordless Headset Telephone is an example of  
superior design and craftsmanship. The following suggestions will help you care for your  
phone so you can enjoy it for years.  
Keep the phone dry. If it gets wet, wipe it dry immediately. Liquids might  
contain minerals that can corrode the electronic circuits.  
Use and store the phone only in normal temperature environments. Tem-  
perature extremes can shorten the life of electronic devices and distort or  
melt plastic parts.  
Handle the phone gently and carefully. Dropping it can damage circuit  
boards and cases and can cause the phone to work improperly.  
Keep the phone away from dust and dirt, which can cause premature wear  
of parts.  
Wipe the phone with a damp cloth occasionally to keep it looking new. Do  
CLEANER  
not use harsh chemicals, cleaning solvents, or strong detergents to clean  
your phone.  
Modifying or tampering with the phone’s internal components can cause a malfunction  
and might invalidate its warranty and void your FCC authorization to operate it. If your  
phone is not performing as it should, take it to your local RadioShack store for assis-  
tance. If the trouble is harming the phone lines, the telephone company might ask you to  
disconnect your phone until you have resolved the problem.  
18  
Download from Www.Somanuals.com. All Manuals Search And Download.  
43-1048.fm Page 19 Tuesday, August 17, 1999 12:45 PM  
2. Gently pull on the battery connector  
to disconnect it, then remove the bat-  
tery pack.  
REPLACING THE BATTERY  
PACK  
If you follow the instructions in “Connect-  
ing and Charging the Battery Pack” on  
Page 7, the battery pack should last  
about a year. If the battery pack does not  
hold a charge for more than 2 hours after  
an overnight charge, replace the battery  
pack with a new 3.6 volt, 300 milliamp  
battery pack with a connector that fits the  
connector pins in the battery pack com-  
partment. You can order a replacement  
battery pack (RSU-10450971) through  
your local RadioShack store.  
3. Slide the battery pack’s connector  
onto the connector pins inside the  
battery compartment and put the bat-  
tery pack into the compartment.  
Illustration  
Install the new battery pack as described  
below, then charge the battery pack for  
about 15 hours before you use it the first  
time (see “Connecting and Charging the  
Battery Pack” on Page 7).  
4. Replace the cover and secure it with  
the screw.  
Cautions:  
• You must use a replacement battery  
pack of the required size and type.  
1. Use a Phillips screwdriver to remove  
the screw on the battery compartment  
cover on the remote keypad, then re-  
move the cover.  
• Be careful not to short the battery  
pack by touching it with conducting  
materials, such as rings, bracelets,  
and keys. The battery pack or con-  
ductor might overheat and burn.  
Illustration  
• Do not dispose of the battery pack in  
a fire because it might explode.  
• Do not open or mutilate the battery  
pack.  
19  
Download from Www.Somanuals.com. All Manuals Search And Download.  
43-1048.fm Page 20 Tuesday, August 17, 1999 12:45 PM  
Notes:  
cal, the phone company notifies you as  
soon as possible and advises you of your  
right to file a complaint with the FCC.  
• If you have trouble replacing the bat-  
tery pack, take the phone to your lo-  
cal RadioShack store for assistance.  
Also, the phone company can make  
changes to its lines, equipment, opera-  
tions, or procedures that could affect the  
operation of this telephone. The tele-  
phone company notifies you of these  
changes in advance, so you can take the  
necessary steps to prevent interruption of  
your telephone service.  
To avoid losing numbers stored in  
memory, try to install and begin  
charging the new battery pack within  
2 minutes of removing the old one.  
Important: Your telephone contains a re-  
chargeable nickel cadmium battery pack.  
At the end of the battery pack’s useful life,  
it must be recycled or disposed of proper-  
ly. Contact your local, county, or state  
hazardous waste management authori-  
ties for information on recycling or dispos-  
al programs in your area. Some options  
that might be available are: municipal  
curb-side collection, drop-off boxes at re-  
tailers such as your local RadioShack  
store, recycling collection centers, and  
mail-back programs.  
Your phone might cause TV or radio inter-  
ference even when it is operating proper-  
ly. To determine whether your phone is  
causing the interference, turn off your  
phone. If the interference goes away,  
your phone is causing the interference.  
Try to eliminate the interference by:  
• Moving your phone away from the re-  
ceiver  
• Connecting your phone to an AC out-  
let that is on a different electrical cir-  
cuit from the receiver  
THE FCC WANTS YOU TO  
KNOW  
• Contacting your local RadioShack  
store for help  
In the unlikely event that your phone  
causes problems on the phone line, the  
phone company can temporarily discon-  
tinue your service. If this happens, the  
phone company attempts to notify you in  
advance. If advance notice is not practi-  
20  
Download from Www.Somanuals.com. All Manuals Search And Download.  
43-1048.fm Page 21 Tuesday, August 17, 1999 12:45 PM  
LIGHTNING  
Your telephone has built-in lightning pro-  
tection to reduce the risk of damage from  
surges in telephone line and power line  
current. This lightning protection meets or  
exceeds FCC requirements. However,  
lightning striking the telephone or power  
lines can damage your telephone.  
Lightning damage is not common. Never-  
theless, if you live in an area that has se-  
vere electrical storms, we suggest that  
you unplug your phone during storms to  
reduce the possibility of damage.  
21  
Download from Www.Somanuals.com. All Manuals Search And Download.  
43-1048.fm Page 22 Tuesday, August 17, 1999 12:45 PM  
NOTES  
22  
Download from Www.Somanuals.com. All Manuals Search And Download.  
43-1048.fm Page 23 Tuesday, August 17, 1999 12:45 PM  
23  
Download from Www.Somanuals.com. All Manuals Search And Download.  
43-1048.fm Page 24 Tuesday, August 17, 1999 12:45 PM  
RadioShack Limited Warranty  
This telephone product is warranted against manufacturing defects in material and  
workmanship for one (1) year from the date of purchase from RadioShack company  
owned stores and authorized RadioShack franchisees and dealers. Within this period,  
RadioShack will repair it without charge for parts and labor. Simply bring your  
RadioShack sales slip as proof-of-purchase date to any RadioShack store.  
This warranty does not cover damage or failure caused by or attributable to Acts of  
God, abuse, misuse, improper or abnormal usage, faulty installation, improper mainte-  
nance, lightning or other incidence of excess voltage, or any repairs other than those  
provided by a RadioShack Authorized Service Facility, or transportation costs.  
RadioShack is not responsible or liable for indirect, special, or consequential  
damages arising out of or in connection with the use or performance of the prod-  
uct or other damages with respect to loss of property, loss of revenue or profit, or  
costs of removal, installation or reinstallation.  
EXCEPT AS PROVIDED HEREIN, RadioShack MAKES NO EXPRESS WARRANTIES  
AND ANY IMPLIED WARRANTIES ARE LIMITED IN DURATION TO THE DURATION  
OF THE WRITTEN LIMITED WARRANTIES CONTAINED HEREIN. Some states do  
not allow the limitation or exclusion of incidental or consequential damages and some  
states do not allow limitation or exclusion of implied warranties; therefore, the aforesaid  
limitation(s) or exclusion(s) may not apply to the purchaser. There will be charges ren-  
dered for repairs to the product made after the expiration of the aforesaid one (1) year  
warranty period.  
This warranty gives you specific legal rights and you may also have other rights which vary from  
state to state.  
We Service What We Sell  
10/95  
RadioShack  
A Division of Tandy Corporation  
Fort Worth, Texas 76102  
1A7  
Printed in Hong Kong  
Download from Www.Somanuals.com. All Manuals Search And Download.  

QSC Audio Car Amplifier CMX300V User Guide
Raypak Swimming Pool Heater 2002B User Guide
RuggedCom Switch RS930L User Guide
Russound Speaker R12DT User Guide
Sakar Digital Camera 84379 User Guide
Samsung Barcode Reader 901B User Guide
Samsung Camcorder DC161WBi User Guide
Samsung MP3 Player YP K5JZBY User Guide
Sceptre Technologies Flat Panel Television X37 User Guide
SEH Computertechnik Network Card PS54 G User Guide