43-1112.fm Page 1 Monday, September 13, 1999 5:08 PM
Cat. No. 43-1112
OWNER’S MANUAL
Please read before using this equipment.
ET-1112
900 MHz Digital Spread Spectrum
Cordless Phone
Download from Www.Somanuals.com. All Manuals Search And Download.
43-1112.fm Page 3 Monday, September 13, 1999 5:08 PM
Important:
This symbol is intended to inform
you that important operating and
maintenance instructions are
included in the literature accom-
panying this product.
• Cordless phones such as this one
require AC power to operate. When
the AC power is off, you cannot dial
out or receive incoming calls using
your ET-1112. To be safe, you
should also have a phone that does
not need AC power to operate (not a
cordless phone) so you can still
make and receive calls if there is an
AC power failure.
!
READ THIS BEFORE
INSTALLATION
We have designed your phone to con-
form to federal regulations and you can
connect it to most phone lines. However,
each device that you connect to the tele-
phone line draws power from the line.
We refer to this power draw as the
phone’s ringer equivalence number, or
REN. The REN is on the bottom of your
phone.
• When AC power is lost, the ET-1112
loses the security access-protection
code connection between the base
and the handset. When power is
restored, put the handset on the
base briefly to restore this connec-
tion so you can use the handset.
If you use more than one phone or other
device on the line, add up all the RENs.
If the total is more than five (three in ru-
ral areas), your phones might not ring. If
ringer operation is impaired, remove one
of the devices from the line.
WARNING: To reduce the risk of fire or
shock hazard, do not expose this product to rain
or moisture.
CAUTION
RISK OF ELECTRIC SHOCK.
!
DO NOT OPEN.
CAUTION: TO REDUCE THE RISK OF
ELECTRIC SHOCK, DO NOT REMOVE
COVER OR BACK. NO USER-SERVICE-
ABLE PARTS INSIDE. REFER SERVICING
TO QUALIFIED PERSONNEL.
This symbol is intended to alert
you to the presence of uninsu-
lated dangerous voltage within
the product’s enclosure that might
be of sufficient magnitude to con-
stitute a risk of electric shock. Do
not open the product’s case.
3
Download from Www.Somanuals.com. All Manuals Search And Download.
43-1112.fm Page 4 Monday, September 13, 1999 5:08 PM
FCC STATEMENT
Your telephone complies with Part 68 of
FCC Rules. Upon request, you must
provide the phone’s FCC registration
number and REN to your telephone
company. These numbers are on the
bottom of the base.
Note: You must not connect your tele-
phone to:
• coin-operated systems
• party-line systems
• most electronic key phone systems
4
Download from Www.Somanuals.com. All Manuals Search And Download.
43-1112.fm Page 5 Monday, September 13, 1999 5:08 PM
INSTALLATION
2. Plug the modular cord’s other end
into a modular phone line jack.
SELECTING A LOCATION
You can place the phone’s base on a
desk top or table, or mount it on a wall.
Select a location that is:
3. Insert the supplied AC adapter’s
barrel plug into the DC IN 9V jack on
the back of the base.
• near an accessible AC outlet
• near a telephone line jack
• out of the way of normal activities
• away from electrical machinery,
electrical appliances, metal walls or
filing cabinets, wireless intercoms,
alarms, and room monitors
4. Route the adapter’s cord through
the strain relief slot on the base.
• away from other cordless phones
The base’s location affects the hand-
set’s range. If you have a choice of sev-
eral locations, try each to see which
provides the best performance.
Caution: The supplied RadioShack AC
adapter was designed specifically for
your ET-1112. Use only the supplied
adapter.
5. Plug the adapter into a standard AC
outlet.
On a Desk Top
6. Lift the base’s antenna to an upright
position.
Follow these steps when you place the
base on a desk, shelf, or table.
1. Plug one end of the supplied long
modular cord into the TEL LINE jack
on the back of the base.
On a Wall Plate or Wall
1. Plug one end of the supplied short
modular cord into the TEL LINE jack
on the back of the base as in “On a
Desk Top,” Step 1.
2. Insert the supplied AC adapter’s
barrel plug into the DC IN 9V jack as
in “On a Desk Top,” Step 3.
5
Download from Www.Somanuals.com. All Manuals Search And Download.
43-1112.fm Page 6 Monday, September 13, 1999 5:08 PM
3. Route the adapter and modular
cords through the grooves on the
bottom of the base.
7. Lift the base’s antenna to an upright
position.
Note: To mount the ET-1112 directly on
a wall, you need two screws (not sup-
plied) with heads that fit into the keyhole
slots on the bottom of the base.
Follow the steps under “On a Wall Plate
or Wall” on Page 5, then apply these ad-
ditional instructions for placement on a
wall.
1. Drill two holes 315/16
inches (100 mm)
apart. Then thread
a screw into each
4. Plug the modular cord’s other end
into the wall plate jack, then align
the base’s keyhole slots with the
wall plate studs and slide the base
downward to secure it.
5/16
Inch
315/16
Inch
hole, letting the
heads extend about
5/16 inch (8 mm)
from the wall.
2. Plug one end of the supplied long
modular cord into the TEL LINE jack
on the back of the base.
3. Align the base’s keyhole slots with
the mounting screws and slide the
base downward to secure it.
5. Plug the adapter into a standard AC
outlet.
6. Press and lift out the handset
holder, rotate it 180°, then snap it
back into place so it holds the hand-
set.
Handset
Holder
6
Download from Www.Somanuals.com. All Manuals Search And Download.
43-1112.fm Page 7 Monday, September 13, 1999 5:08 PM
To charge the battery pack, simply place
the handset on the base. The CHARGE/
IN USE indicator on the base lights.
CONNECTING AND
CHARGING THE BATTERY
PACK
The phone comes with a rechargeable
nickel-cadmium battery pack in the
handset, but not connected. Before us-
ing your phone, you must connect the
battery pack and then charge it for about
24 hours.
1. Press down and slide the battery
compartment cover in the direction
of the arrow to remove it.
Recharge the battery pack when the
handset beeps and the TALK/BATT indi-
cator flashes.
Important: Be sure the battery pack is
properly connected before you try to
charge it. The CHARGE/INUSE indica-
tor lights when the handset is on the
base, even if the battery pack is not con-
nected.
2. Unfasten the battery retainer strap
and lift the battery pack out of the
compartment. Plug the battery
pack’s connector into the socket in
the compartment. The connector fits
only one way.
Notes:
• When you first use the phone after
charging or recharging the battery
pack, the phone might not work and
you might hear an error tone. If this
happens, return the handset to the
base for a few seconds.
• About once a month, fully discharge
the battery pack by keeping the
handset off the base until the TALK/
BATT indicator flashes. Otherwise,
the battery pack loses its ability to
fully recharge.
3. Put the battery pack in the compart-
ment and fasten the battery retainer
strap.
4. Replace the cover.
7
Download from Www.Somanuals.com. All Manuals Search And Download.
43-1112.fm Page 8 Monday, September 13, 1999 5:08 PM
• Using a pencil eraser, clean the
charging contacts on the handset
and the base about once a month.
SETTING THE DIALING
MODE
Set PULSE-TONE on the back of the
base for the type of service you have. If
you are not sure which type you have,
once the battery pack is fully charged,
do this test.
1. Be sure PULSE-TONE is set to TONE.
2. Lift the handset, press TALK, and lis-
ten for a dial tone.
3. Press any number other than 0.
• If the TALK/BATT indicator does not
light and the phone does not work,
recharge the battery pack. (The bat-
tery power might be too low to light
the indicator.)
Note: If your phone system requires
that you dial an access code (9, for
example) before you dial an outside
number, do not press the access
code either.
• If the battery pack becomes weak
during a call, you hear a beep and
the TALK/BATT indicator flashes
every 4 seconds. Recharge the bat-
tery pack.
If the dial tone stops, you have
touch-tone service. Leave PULSE-
TONE set to TONE.
If the dial tone continues, you have
pulse service. Set PULSE-TONE to
PULSE.
• If the battery pack is completely dis-
charged, the handset loses the
security access-protection code. To
reset the code, place the handset on
the base and charge the battery
pack.
• The supplied battery pack should
last for about a year. When the bat-
tery pack loses its ability to fully
recharge, order a replacement bat-
tery
pack
from
your
local
RadioShack store (see “Replacing
the Battery Pack” on Page 18).
8
Download from Www.Somanuals.com. All Manuals Search And Download.
43-1112.fm Page 9 Monday, September 13, 1999 5:08 PM
SETTING THE RINGER’S
TONE AND VOLUME
You can set four ringer tones and a high
and low volume for each.
To change the tone, lift the handset and
press FLASH. Then, enter the ringer
tone number (1–4) using the number
keys. The selected tone sounds briefly.
FLASH
To hear and change the ringer volume
setting, press or
.
9
Download from Www.Somanuals.com. All Manuals Search And Download.
43-1112.fm Page 10 Monday, September 13, 1999 5:08 PM
OPERATION
MAKING AND RECEIVING
CALLS
SETTING THE HANDSET
VOLUME
To make a call, lift the handset and
press TALK. The TALK indicator on the
handset and the IN USE indicator on the
base light. When you hear a dial tone,
dial the number.
You can choose one of four volume set-
tings — low, medium, high, or maximum
— for the handset. To change the vol-
ume, press or during a call.
USING REDIAL
TALK
You can quickly dial the last number di-
aled. When you hear a dial tone, simply
press REDIAL.
Notes:
• The redial memory holds up to 32
digits, so you can redial long-dis-
tance as well as local numbers.
To answer a call, lift the handset if nec-
essary then press TALK.
The ET-1112 scans 20 channels (fre-
quency pairs used between the base
and the handset) and automatically se-
lects a clear channel each time you
make or receive a call.
• The redial memory also holds pause
entries. See “Entering a Pause” on
Page 13.
Note: If the handset is too far from the
base, the channel might not be clear.
Move closer to the base and try making
the call again.
MUTE
REDIAL
To end a call, place the handset on the
base or press TALK.
Note: If you press TALK to hang up and
the phone does not disconnect, press
TALK again while holding the handset
closer to the base, or place the handset
on the base.
USING MUTE
To talk to someone in the room without
the person on the other end of the
phone line hearing your conversation,
press MUTE. The TALK/BATT indicator
flashes.
10
Download from Www.Somanuals.com. All Manuals Search And Download.
43-1112.fm Page 11 Monday, September 13, 1999 5:08 PM
Press MUTE again to resume your
phone conversation.
PAGING
To page the person who has the hand-
set or to locate the handset when the
phone is not in use, press PAGE on the
base. The handset beeps for about 15
seconds. To stop the beeping sooner,
press TALK on the handset twice or
PAGE on the base.
USING FLASH
FLASH performs the electronic equiva-
lent of a switchhook operation for spe-
cial services, such as Call Waiting.
For example, if you have Call Waiting,
press FLASH to answer an incoming call
without disconnecting the current call.
Press FLASH again to return to the first
call.
Note: If you do not have any special
phone services, pressing FLASH might
disconnect the current call.
PAGE
USING TONE SERVICES
ON A PULSE LINE
Some special services, such as bank-
by-phone, require tone signals. If you
have pulse service, you can still use
these special tone services by following
these steps.
Notes:
• Make sure you press TALK twice to
stop the handset from beeping. If
you press TALK only once, you get a
dial tone.
1. Be sure PULSE-TONE is set to
PULSE.
• If you receive a call while the page is
sounding, the handset stops beep-
ing and starts ringing.
2. Dial the service’s main number.
3. When the service answers, press
TONE ( ). Any additional numbers
you dial are sent as tone signals.
4. After you complete the call, return
the handset to the base or press
TALK. The phone automatically
resets to the pulse mode.
11
Download from Www.Somanuals.com. All Manuals Search And Download.
43-1112.fm Page 12 Monday, September 13, 1999 5:08 PM
• Each tone or pause entry uses
one digit of memory.
MEMORY DIALING
The ET-1112 can store three telephone
numbers in speed dial memory, and you
can dial any one of these numbers by
pressing a single button. You can also
store up to 20 more numbers that you
can dial by entering a two-digit memory
location number.
4. To assign the number to a speed
dial button, press MEM, then press a
speed dial button (M1–M3).
To store the number in a standard
memory location, press MEM, then
enter the two-digit memory location
number (01–20).
The handset sounds a long beep to
indicate that the number is stored.
Storing a Number in Memory
Note: An error tone sounds and the
phone exits the storing process if you
wait more than 30 seconds between
each key press.
5. For each stored number, write the
person’s or company’s name next to
the appropriate location number on
the supplied memory directory
sticker. Peel the backing off the
sticker and attach it to the phone.
1. Lift the handset.
2. Press MEM. The TALK/BATT indica-
tor blinks.
MEM
To replace a stored number, simply
store a new one in its place.
3. Enter the number and any tone
mode changes or pause entries
(see “Entering a Pause”).
To delete a stored number, lift the
handset and press MEM twice, then
enter the memory location number
(01–20) or press the speed dial but-
ton (M1–M3) you want to clear. The
handset sounds a long beep to sig-
nal that the memory location is
clear.
Notes:
• Each number you store can be up
to 16 digits long.
• If you try to enter more than 16
digits, the phone sounds an error
tone and exits the storing pro-
cess. Start over from Step 2.
12
Download from Www.Somanuals.com. All Manuals Search And Download.
43-1112.fm Page 13 Monday, September 13, 1999 5:08 PM
Dial the service’s main number first.
Then, at the appropriate place in the
call, press the memory location button
(M1–M3), or press MEM and enter the
memory location number (01–20) for the
stored information.
Entering a Pause
In some telephone systems, you must
dial an access code (9, for example) and
wait for a second dial tone before you
can dial an outside number. You can
store the access code with the phone
number. However, you should also store
a pause after the access code to allow
the outside line time to connect. To en-
ter a 2-second pause, press REDIAL.
For a longer pause, press REDIAL addi-
tional times.
Testing Stored Emergency
Numbers
If you store an emergency service’s
number (police department, fire depart-
ment, ambulance) and you choose to
test the stored number, make the test
call during the late evening or early
morning hours to avoid peak demand
periods. Also, remain on the line to ex-
plain the reason for your call.
Dialing a Memory Number
To dial a number assigned to a speed
dial button, simply press the button (M1–
M3) for the number you want to dial.
(You do not need to press TALK first.)
USING A HEADSET
To dial a number stored in a standard
memory location, press TALK. When you
hear a dial tone, press MEM and enter
the two-digit memory location number
for the number you want to dial.
You can talk with hands-free conve-
nience using an optional headset that
3
has a /32-inch (2.5-mm) plug. Contact
your local RadioShack store for a suit-
able headset.
Note: If you select an invalid memory lo-
cation (for example 3 instead of 03), the
phone sounds an error tone. Press MEM
again and re-enter the memory location
number.
To connect the headset, open the rub-
ber cover marked
on the side of the
handset, then insert the headset’s plug
into the jack.
Notes:
Chain-Dialing Service Numbers
• Connecting a headset disconnects
the handset’s earpiece and micro-
phone.
For quick recall of numbers for special
services (such as alternate long dis-
tance or bank-by-phone), store each
group of numbers in its own memory lo-
cation.
•
or on the handset also controls
the connected headset’s volume.
13
Download from Www.Somanuals.com. All Manuals Search And Download.
43-1112.fm Page 14 Monday, September 13, 1999 5:08 PM
• If you place the handset on the base
while the headset is connected, be
sure the handset seats properly.
With a headset connected, you can
make or answer calls as usual using the
keys on the handset.
You can use a handset holder (available
from your local RadioShack store) to
hang the handset on your belt for great-
er convenience.
When you finish using the headset, dis-
connect it and close the rubber cover to
protect the jack.
14
Download from Www.Somanuals.com. All Manuals Search And Download.
43-1112.fm Page 15 Monday, September 13, 1999 5:08 PM
TROUBLESHOOTING
We do not expect you to have any problems with your ET-1112, but if you do, the fol-
lowing suggestions might help.
Problem
Suggestion
The phone does not work or
works poorly.
Be sure the base’s phone line cord and AC adapter are
correctly and securely connected, and the battery pack
in the handset is charged.
Return the handset to the base for a few seconds to
reset the security access-protection code.
The handset stops working or
works poorly during a call.
Move the handset closer to the base.
Lift the base’s antenna to a fully upright position.
Be sure the handset’s battery pack is charged. (If the
battery pack power is too low, it does not have enough
power to light the LOW BATT indicator.)
Low volume or unusual sounds. Someone has picked up another phone on the same
line. Hang up the other phone.
Severe noise interference.
Keep the handset and base away from computers,
remote control toys, wireless microphones, alarm sys-
tems, intercoms, room monitors, fluorescent lights, and
electrical appliances.
Move to another location or turn off the source of inter-
ference.
Hang up and redial the number.
The phone cannot be operated
at a useful distance from the
base because the signal
becomes weak or noisy (hand-
set’s range has decreased).
Lift the base’s antenna to a fully upright position.
Be sure neither the handset or base antenna is touching
a metal surface.
Recharge the battery pack.
The handset battery pack does
not charge.
Check the charging contacts on the handset and base. If
they are dirty, clean them with a pencil eraser.
Be sure the battery pack is properly connected.
Be sure the handset is properly seated on the base.
15
Download from Www.Somanuals.com. All Manuals Search And Download.
43-1112.fm Page 16 Monday, September 13, 1999 5:08 PM
Problem
Suggestion
Handset does not ring or
receive a page.
Lift the base’s antenna to a fully upright position.
Move the handset closer to the base.
Move the base away from other electrical devices.
Recharge the battery pack.
If you still have problems, disconnect the phone. If other phones on the same line
work properly, the fault is in this phone or its installation. If you cannot find the prob-
lem, take your ET-1112 to your local RadioShack store for assistance.
16
Download from Www.Somanuals.com. All Manuals Search And Download.
43-1112.fm Page 17 Monday, September 13, 1999 5:08 PM
CARE AND MAINTENANCE
Your RadioShack ET-1112 900 MHz Digital Spread Spectrum Cordless Telephone
is an example of superior design and craftsmanship. The following suggestions will
help you care for your ET-1112 so you can enjoy it for years.
Keep the ET-1112 dry. If it gets wet, wipe it dry immediately. Liquids
might contain minerals that can corrode the electronic circuits.
Use and store the ET-1112 only in normal temperature environments.
Temperature extremes can shorten the life of electronic devices, dam-
age batteries, and distort or melt plastic parts.
Keep the ET-1112 away from dust and dirt, which can cause premature
wear of parts.
Handle the ET-1112 gently and carefully. Dropping it can damage circuit
boards and cases and can cause the ET-1112 to work improperly.
Use only fresh batteries of the required size and recommended type.
Batteries can leak chemicals that damage your ET-1112’s electronic
parts.
Wipe the ET-1112 with a damp cloth occasionally to keep it looking new.
Do not use harsh chemicals, cleaning solvents, or strong detergents to
clean the ET-1112.
Modifying or tampering with the ET-1112’s internal components can cause a mal-
function and might invalidate its warranty and void your FCC authorization to operate
it. If your ET-1112 is not performing as it should, take it to your local RadioShack
store for assistance. If the trouble is affecting the telephone lines, the phone compa-
ny can ask you to disconnect your ET-1112 until you have resolved the problem.
17
Download from Www.Somanuals.com. All Manuals Search And Download.
43-1112.fm Page 18 Monday, September 13, 1999 5:08 PM
• Be careful not to short the battery
pack by touching the connector’s
pins with conducting materials, such
as rings, bracelets, and keys. The
battery pack or conductor might
overheat and burn.
REPLACING THE
BATTERY PACK
If you follow the instructions in “Connect-
ing and Charging the Battery Pack” on
Page 7, the battery pack should last
about one year. If the battery pack does
not hold a charge for more than 2 hours
after an overnight charge, replace it with
a new 3.6-volt, 600 mAh battery pack
with a connector that fits the socket in
the battery compartment. You can order
a replacement battery pack through your
local RadioShack store.
If you have trouble replacing the battery
pack, take the phone to your local Ra-
dioShack store for assistance.
Important: This tele-
phone can use nickel-
cadmium rechargeable
batteries. At the end of a
nickel-cadmium battery's
useful life, it must be re-
0
0
8
3
4
Install the new battery pack as de-
scribed below, then charge it for about
24 hours.
cycled or disposed of properly. Contact
your local, county, or state hazardous
waste management authorities for infor-
mation on recycling or disposal pro-
grams in your area or call 1-800-843-
7422. Some options that might be avail-
able are: municipal curbside collection,
drop-off boxes at retailers such as your
local RadioShack store, recycling collec-
tion centers, and mail-back programs.
1. Press down and slide off the cover.
2. Unfasten the battery retainer strap
and lift the battery pack out of the
compartment, then gently pull on
the battery connector to disconnect
it.
3. Insert the new battery pack’s con-
nector into the socket in the com-
partment, place the battery pack
into the compartment, and fasten
the battery retainer strap.
THE FCC WANTS YOU TO
KNOW
4. Replace the cover.
In the unlikely event that your phone
causes problems on the phone line, the
phone company can temporarily discon-
tinue your service. If this happens, the
phone company attempts to notify you in
advance. If advance notice is not practi-
cal, the phone company notifies you as
soon as possible and advises you of
your right to file a complaint with the
FCC.
Cautions:
• You must use a replacement battery
pack of the same size and type.
• Do not dispose of the battery pack
in a fire because it might explode.
• Do not open or mutilate the battery
pack.
18
Download from Www.Somanuals.com. All Manuals Search And Download.
43-1112.fm Page 19 Monday, September 13, 1999 5:08 PM
Also, the phone company can make
changes to its lines, equipment, opera-
tions, or procedures that could affect the
operation of this telephone. The tele-
phone company notifies you of these
changes in advance, so you can take
the necessary steps to prevent interrup-
tion of your telephone service.
LIGHTNING
Your telephone has built-in lightning pro-
tection to reduce the risk of damage
from surges in telephone line and power
line current. This lightning protection
meets or exceeds FCC requirements.
However, lightning striking the tele-
phone or power lines can damage your
telephone.
Your phone might cause TV or radio in-
terference even when it is operating
properly. To determine whether your
phone is causing the interference, turn
off your phone. If the interference goes
away, your phone is causing it. Try to
eliminate the interference by:
Lightning damage is not common. Nev-
ertheless, if you live in an area that has
severe electrical storms, we suggest
that you unplug your phone during
storms to reduce the possibility of dam-
age.
• moving your phone away from the
receiver
• connecting your phone to an AC
outlet that is on a different electrical
circuit from the receiver
• contacting your local RadioShack
store for help
If you cannot eliminate the interference,
the FCC requires that you stop using
your phone.
Some cordless telephones operate on
frequencies that might cause interfer-
ence to nearby TVs and VCRs. To mini-
mize or prevent such interference, the
base of the cordless telephone should
not be placed near or on top of a TV or
VCR.
19
Download from Www.Somanuals.com. All Manuals Search And Download.
43-1112.fm Page 20 Monday, September 13, 1999 5:08 PM
Limited One-Year Warranty
This product is warranted by RadioShack against manufacturing defects in material and workman-
ship under normal use for one (1) year from the date of purchase from RadioShack company-owned
stores and authorized RadioShack franchisees and dealers. EXCEPT AS PROVIDED HEREIN, Ra-
dioShack MAKES NO EXPRESS WARRANTIES AND ANY IMPLIED WARRANTIES, INCLUDING
THOSE OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE, ARE LIMITED
IN DURATION TO THE DURATION OF THE WRITTEN LIMITED WARRANTIES CONTAINED
HEREIN. EXCEPT AS PROVIDED HEREIN, RadioShack SHALL HAVE NO LIABILITY OR RE-
SPONSIBILITY TO CUSTOMER OR ANY OTHER PERSON OR ENTITY WITH RESPECT TO ANY
LIABILITY, LOSS OR DAMAGE CAUSED DIRECTLY OR INDIRECTLY BY USE OR PERFOR-
MANCE OF THE PRODUCT OR ARISING OUT OF ANY BREACH OF THIS WARRANTY, INCLUD-
ING, BUT NOT LIMITED TO, ANY DAMAGES RESULTING FROM INCONVENIENCE, LOSS OF
TIME, DATA, PROPERTY, REVENUE, OR PROFIT OR ANY INDIRECT, SPECIAL, INCIDENTAL,
OR CONSEQUENTIAL DAMAGES, EVEN IF RadioShack HAS BEEN ADVISED OF THE POSSI-
BILITY OF SUCH DAMAGES.
Some states do not allow the limitations on how long an implied warranty lasts or the exclusion of in-
cidental or consequential damages, so the above limitations or exclusions may not apply to you.
In the event of a product defect during the warranty period, take the product and the RadioShack
sales receipt as proof of purchase date to any RadioShack store. RadioShack will, at its option, un-
less otherwise provided by law: (a) correct the defect by product repair without charge for parts and
labor; (b) replace the product with one of the same or similar design; or (c) refund the purchase
price. All replaced parts and products, and products on which a refund is made, become the prop-
erty of RadioShack. New or reconditioned parts and products may be used in the performance of
warranty service. Repaired or replaced parts and products are warranted for the remainder of the
original warranty period. You will be charged for repair or replacement of the product made after the
expiration of the warranty period.
This warranty does not cover: (a) damage or failure caused by or attributable to acts of God, abuse,
accident, misuse, improper or abnormal usage, failure to follow instructions, improper installation or
maintenance, alteration, lightning or other incidence of excess voltage or current; (b) any repairs
other than those provided by a RadioShack Authorized Service Facility; (c) consumables such as
fuses or batteries; (d) cosmetic damage; (e) transportation, shipping or insurance costs; or (f) costs
of product removal, installation, set-up service adjustment or reinstallation.
This warranty gives you specific legal rights, and you may also have other rights which vary from
state to state.
RadioShack Customer Relations, 200 Taylor Street, 6th Floor, Fort Worth, TX 76102
We Service What We Sell
04/99
RadioShack
A Division of Tandy Corporation
Fort Worth, Texas 76102
UCZZ01635BZ
09A99
Printed in the Philippines
Download from Www.Somanuals.com. All Manuals Search And Download.
|