43-1105.fm Page 1 Monday, August 30, 1999 1:57 PM
Cat. No. 43-1105
OWNER’S MANUAL
Please read before using this equipment.
ET-1105
Digital Spread Spectrum
900 MHz Cordless Telephone
with Caller ID/Call Waiting ID
Download from Www.Somanuals.com. All Manuals Search And Download.
43-1105.fm Page 3 Monday, August 30, 1999 1:57 PM
Review Scrolling — lets you easily
scroll through all information stored in
the ET-1105’s Caller ID memory.
This telephone has been tested and
found to comply with all applicable UL
and FCC standards.
Phone Information Display — lets you
see incoming Caller ID information and
phone numbers as you dial them or re-
call them from the ET-1105’s memory
and Caller ID records.
WARNING: To reduce the risk of fire or shock
hazard, do not expose this product to rain or
moisture.
CAUTION
Trilingual Messages — lets you set the
phone to display messages in English,
French, or Spanish.
RISK OF ELECTRIC SHOCK.
!
DO NOT OPEN.
CAUTION: TO REDUCE THE RISK OF
ELECTRIC SHOCK, DO NOT REMOVE
COVER OR BACK. NO USER-SERVICE-
ABLE PARTS INSIDE. REFER SERVICING
TO QUALIFIED PERSONNEL.
Out of Range Signal — the handset
beeps twice to let you know when you
move out of the base’s operating range.
This symbol is intended to alert
you to the presence of uninsu-
lated dangerous voltage within
the product’s enclosure that might
be of sufficient magnitude to con-
stitute a risk of electric shock. Do
not open the product’s case.
Security Access-Protection Code —
helps prevent other cordless phone us-
ers from using your phone line while the
handset is off the base.
Flash — sends an electronic switchhook
signal for use with special phone servic-
es such as Call Waiting.
This symbol is intended to inform
you that important operating and
maintenance instructions are
included in the literature accom-
panying this product.
!
Redial — lets you quickly redial the last
number dialed.
Tone/Pulse Dialing — lets you use your
phone with tone or pulse service.
3
Download from Www.Somanuals.com. All Manuals Search And Download.
43-1105.fm Page 4 Monday, August 30, 1999 1:57 PM
ference. This lack of privacy can occur
with any cordless phone.
Important Caller ID Information
To use the phone’s Caller ID and Call
Waiting features, you must be in an area
where Caller ID and Call Waiting servic-
es are available and you must subscribe
to the services.
READ THIS BEFORE
INSTALLATION
Each device that you connect to the
phone line draws power from the phone
line. We refer to this power draw as the
device’s ringer equivalence number, or
REN. The REN is on the bottom of the
base.
Where Caller ID is offered, one or more
of the following options are generally
available:
• Caller’s number only
• Caller’s name only
• Caller’s name and number
If you are using more than one phone or
other device on the line, add up all the
RENs. If the total is more than five (three
in rural areas), your phone might not
ring. If ringer operation is impaired, re-
move a device from the line.
For the ET-1105’s Caller ID memory dial
feature to operate, you must receive the
caller’s number.
Important: Cordless phones such as
this one require AC power to operate.
When the AC power is off, you cannot
dial out or receive incoming calls using
your ET-1105. For this reason, the ET-
1105 cordless phone should not be your
only telephone. To be safe, you should
also have a corded phone that does not
require AC power to operate so you can
still make and receive calls if there is an
AC power failure.
FCC STATEMENT
This telephone complies with Part 68 of
FCC Rules. You must, upon request,
provide the FCC registration number and
the REN to your phone company. These
numbers are on the bottom of the base.
Note: You must not connect your ET-
1105 to any of the following:
Your telephone operates on standard ra-
dio frequencies as allocated by the FCC.
Even though the access protection code
prevents unauthorized use of your phone
line, it is possible for other radio units op-
erating on similar frequencies within a
certain area to unintentionally intercept
your conversations and/or cause inter-
• coin-operated systems
• party-line systems
• most electronic key phone systems
4
Download from Www.Somanuals.com. All Manuals Search And Download.
43-1105.fm Page 5 Monday, August 30, 1999 1:57 PM
CONTENTS
Preparation .............................................................................................................. 6
Selecting a Location ........................................................................................... 6
Attaching the Handset’s Antenna ....................................................................... 6
Placing the Base on a Desk Top ........................................................................ 6
Mounting the Base on a Wall Plate .................................................................... 8
Connecting and Charging the Battery Pack ....................................................... 9
Setting the Dialing Mode .................................................................................. 11
Selecting the Language .................................................................................... 11
Setting the Area Code ...................................................................................... 12
Setting the Ringer ............................................................................................. 12
Turning the Ringer On or Off ...................................................................... 12
Checking/Setting the Ringer ...................................................................... 12
Using a Headset ............................................................................................... 13
Removing the Belt Clip ..................................................................................... 13
Telephone Operation ............................................................................................ 14
Making and Receiving a Call ............................................................................ 14
Setting the Handset’s Volume .......................................................................... 14
Using Redial ..................................................................................................... 14
Using Flash ...................................................................................................... 15
Using Tone Services on a Pulse Line ............................................................... 15
Using Page ....................................................................................................... 15
Memory Dialing ................................................................................................ 15
Storing a Number and Name in Memory ................................................... 16
Using the VIP Call List ............................................................................... 16
Entering a Pause ....................................................................................... 17
Recalling Numbers Stored in Memory ....................................................... 17
Dialing a Memory Number ......................................................................... 17
Chain-Dialing Service Numbers ................................................................. 17
Testing Stored Emergency Numbers ......................................................... 18
Deleting Information in a Single Memory Location .................................... 18
Deleting Information in All Memory Locations ........................................... 18
Caller ID Operation ............................................................................................... 19
Caller ID Displays ............................................................................................. 20
Reviewing Caller ID Records ............................................................................ 21
Storing Caller ID Records in a Memory Location ............................................. 21
Dialing Numbers from a Caller ID Record ........................................................ 21
Deleting Caller ID Records ............................................................................... 21
Troubleshooting .................................................................................................... 22
Care and Maintenance .......................................................................................... 25
5
Download from Www.Somanuals.com. All Manuals Search And Download.
43-1105.fm Page 6 Monday, August 30, 1999 1:57 PM
PREPARATION
SELECTING A LOCATION
PLACING THE BASE ON A
DESK TOP
You can place the phone on a desk top
or table, or mount it on a standard wall
plate. Select a location that is:
Follow these steps to place the base on
a desk, shelf, or table.
• near an accessible AC outlet
• near a telephone line jack
1. Remove the bracket by holding in
both tabs and gently pulling out the
wide end of the bracket.
• out of the way of normal activities
Tabs
• away from electrical machinery,
electrical appliances, metal walls or
filing cabinets, wireless intercoms,
alarms, and room monitors
The base’s location affects the phone’s
range. If you have a choice of several lo-
cations, try each to see which provides
the best performance.
2. Plug one end of the supplied long
modular cord into the phone jack on
the back of the base.
Caution: The supplied AC adapter was
designed specifically for your ET-1105.
Use only the supplied adapter.
ATTACHING THE
HANDSET’S
ANTENNA
Screw the antenna into the
hole at the top of the hand-
set.
6
Download from Www.Somanuals.com. All Manuals Search And Download.
43-1105.fm Page 7 Monday, August 30, 1999 1:57 PM
3. Insert the supplied AC adapter’s
barrel plug into the DC 9V jack on
the back of the base.
4. Route the adapter’s cord through
the strain relief slot on the bottom of
the base.
6. Plug the modular cord’s other end
into a modular phone line jack.
7. Plug the adapter into a standard AC
outlet.
8. Raise the base’s antenna to a verti-
cal position.
5. Insert the tabs on the narrow end of
the bracket into both upper slots on
the bottom of the base as shown
and push the tabs on the wide end
of the bracket into the upper slots on
the bottom of the base.
7
Download from Www.Somanuals.com. All Manuals Search And Download.
43-1105.fm Page 8 Monday, August 30, 1999 1:57 PM
4. Push the tabs on the wide end of the
bracket into the lower slots on the
bottom of the base.
MOUNTING THE BASE ON
A WALL PLATE
1. Follow Steps 1 through 3 under
“Placing the Base on a Desk Top” on
Page 6.
2. Route the modular cord through the
left groove on the bottom of the base
and the adapter cord through the
groove below the strain relief slot.
5. Plug the short modular cord’s other
end into the wall plate jack, align the
base’s keyhole slots with the wall
plate studs, and slide the base
downward to secure it.
3. Insert the tabs on the narrow end of
the bracket into the slots on the bot-
tom of the base as shown and route
the other end of the short modular
cord through the center of the brack-
et.
8
Download from Www.Somanuals.com. All Manuals Search And Download.
43-1105.fm Page 9 Monday, August 30, 1999 1:57 PM
6. Plug the adapter into a standard AC
outlet.
2. Plug the battery pack’s connector
into the socket in the compartment.
The connector fits only one way.
7. Raise the base’s antenna to a verti-
cal position.
Note: For easier battery pack con-
nection, lift it out of the compart-
ment, insert its connector into the
socket, then replace the battery
pack inside the compartment.
3. Replace the cover.
To charge the battery pack, place the
handset on the base. The CHARGE indi-
cator on the base lights.
CONNECTING AND
CHARGING THE BATTERY
PACK
The ET-1105 comes with a rechargeable
nickel-cadmium battery pack in the
handset but not connected. Before using
your phone, you must connect the bat-
tery pack and then charge it for about 16
hours.
1. Press down and slide off the com-
partment cover as shown.
Recharge the battery pack when
and LOW BATTERY appear on the
handset’s display.
9
Download from Www.Somanuals.com. All Manuals Search And Download.
43-1105.fm Page 10 Monday, August 30, 1999 1:57 PM
Notes:
was the handset that lost power,
leave the handset on the base to
charge the battery pack.
• You can place the handset on the
base face down or face up without
removing the belt clip. If you want to
use the hanging hole on the back of
the handset to place the handset on
the wall-mounted base face-up, re-
move the belt clip (see “Removing
the Belt Clip” on Page 13). However,
the battery pack will not fully charge
in this position.
• If the battery pack gets weak during
a call, the handset beeps once ev-
ery 16 seconds. If this happens, you
cannot make another call on the
phone until you recharge the battery
pack.
• About once a month, fully discharge
the battery pack by keeping the
• When you first use the phone after
charging or recharging the battery
pack, the phone might not work and
you might hear an error tone when
you press TALK. If this happens, re-
turn the handset to the base for
about 6 seconds. This resets the se-
curity access protection code.
handset off the base until
and
LOW BATTERYappear. Otherwise,
the battery pack loses its ability to
fully recharge.
• To avoid damage to the battery
pack, always recharge the handset
before battery power grows too
weak to display
.
• If the CHARGE indicator does not
light when you place the handset on
the base, be sure the battery pack
and AC adapter are correctly and
securely connected.
• If you are not going to use your
phone for an extended period of
time, disconnect the battery pack.
This increases the battery pack’s us-
able life.
Also, check the charging contacts
on the handset and the base. If the
contacts are dirty or tarnished,
clean them with a pencil eraser.
• The supplied battery pack should
last for about a year. When it loses
its ability to fully recharge, order a
replacement battery pack from your
local RadioShack store (see “Re-
placing the Battery Pack” on
Page 26).
• If the battery pack gets completely
discharged or the base loses power
while the handset is away from it,
the security access-protection code
needs to be reset. To reset the code,
place the handset on the base. If it
10
Download from Www.Somanuals.com. All Manuals Search And Download.
43-1105.fm Page 11 Monday, August 30, 1999 1:57 PM
SETTING THE DIALING
MODE
SELECTING THE
LANGUAGE
Set T/P (Tone/Pulse) on the back of the
base for the type of service you have. If
you are not sure which type you have,
once the battery is fully charged, do this
test.
The ET-1105 comes set to display all
Caller ID messages in English, but if you
want it to display messages in French or
Spanish, follow these steps.
1. Press SETUP on the handset. LAN-
GUAGE and the currently selected
language appear.
1. Set T/P to T.
T/P
SETUP
2. Lift the handset, then press TALK
Note: If you do not press any key
within 30 seconds after the lan-
guage selection display appears,
the ET-1105 exits the language se-
lection display without changing the
current selection.
and listen for the dial tone.
TALK
2. To select another language, repeat-
edly press #/ until you see the de-
sired language.
3. Press any number other than 0.
Note: If your phone system requires
that you dial an access code (9, for
example) before you dial an outside
number, do not press the access
code either.
#/
If the dial tone stops, you have
touch-tone service. Leave T/P set to
T.
3. Press SETUP to store the selected
language.
If the dial tone continues, you have
pulse service. Set T/P to P.
11
Download from Www.Somanuals.com. All Manuals Search And Download.
43-1105.fm Page 12 Monday, August 30, 1999 1:57 PM
SETTING THE AREA
CODE
SETTING THE RINGER
Turning the Ringer On or Off
When you return a call from a Caller ID
record (see “Dialing Numbers from a
Caller ID Record” on Page 21), your
phone automatically dials 1, the area
code, and the number. The ET-1105 lets
you store one local area code and three
neighborhood area codes. If the number
you call has the same area code with
your local area code, the ET-1105 dials
the 7-digit local number. If the number
you call has the same area code with one
of three neighborhood area codes, the
ET-1105 dials the 10-digit local number.
You can turn the ET-1105’s ringer on
and off. Set RINGER on the side of the
handset to ON to hear an incoming call or
a page from the base. Set RINGER to
OFF to silence the ringer.
Note: With the ringer off, you can still
make or receive calls using this cordless
phone. Telephones on the same line still
ring when there is an incoming call, and
the IN USE indicator on the ET-1105’s
base flashes until you answer the call.
Follow these steps to set area codes.
Note: If you make a mistake or do not
press a key within 10 seconds during
these steps, start again at Step 1.
1. Pres SETUP. The language selection
display appears.
RINGER
2. Press
/ . The currently entered
area codes (or AREACODE=000
000/000/000) appear.
Checking/Setting the Ringer
You can set the ET-1105’s handset to
sound any of three ringer types. The
handset is preset to use the ringer tone
(1). To change or hear the different
tones, press FLASH when the phone is
not in use. PROG. RINGER displays.
With RINGER set to ON, press 1, 2, or 3,
then press FLASH to confirm the setting.
(The last number button you pressed is
the tone you will hear.)
/
3. Enter your local area code first, then
the three neighborhood area codes,
then press SETUP to store them.
12
Download from Www.Somanuals.com. All Manuals Search And Download.
43-1105.fm Page 13 Monday, August 30, 1999 1:57 PM
• If you place the handset on the base
to recharge it while the headset is
connected, be sure the handset
seats properly.
USING A HEADSET
You can make or answer calls with
hands-free convenience using an option-
3
al headset that has a /32-inch (2.5 mm)
plug. We recommend RadioShack Cat.
No. 43-195, which is specially designed
for use with the ET-1105.
REMOVING THE BELT
CLIP
Follow these steps to use a headset.
The belt clip on the back of the handset
lets you hang the handset on your belt for
easy portability. But to use the hanging
hole on the back of the handset to place
the handset on the wall-mounted base
face-up, you must remove the belt clip.
1. Insert the headset’s plug into the
jack on the top of the handset.
Insert a flat-blade screwdriver into either
side of the belt clip, then pull it off.
2. Place the headset on your head with
the earpiece over either ear and ad-
just the microphone boom until it is
about even with your chin.
3. Hang the belt clip on your belt.
4. Make or receive calls as you would
normally (see “Making and Receiv-
ing a Call” on Page 14).
To replace the belt clip, insert either tab
of the belt clip into one of the handset’s
slots, then snap the other tab into hand-
set’s other slot.
Notes:
• Connecting a headset disconnects
the handset’s earpiece and micro-
phone.
13
Download from Www.Somanuals.com. All Manuals Search And Download.
43-1105.fm Page 14 Monday, August 30, 1999 1:57 PM
TELEPHONE OPERATION
• If you hear loud static during a con-
versation, move the handset closer
to the base.
MAKING AND RECEIVING
A CALL
To make a call, lift the handset and
press TALK. PHONEdisplays. When the
TALK indicator lights steadily and you
hear the dial tone, dial the desired phone
number or memory number (see “Memo-
ry Dialing” on Page 15).
• OUT OF RANGEappears when the
distance from the handset to the
base is out of the phone’s range.
SETTING THE HANDSET’S
VOLUME
The ET-1105 displays the phone number
as you dial. Then PHONE disappears,
the duration of your call (after 14 sec-
onds) in minutes and seconds displays.
You can select any of four different vol-
ume settings by repeatedly pressing
VOLUME during a call.
VOLUME
To answer a call if the handset is on the
base, lift the handset and press TALK.
Or, if the handset is away from the base,
press any key on the handset before
speaking. The TALK indicator on the
handset lights and the IN USE indicator
on the base flashes.
USING REDIAL
You can quickly redial the last number di-
aled. Lift the handset and press TALK.
When you hear the dial tone, press REDI-
AL. The number appears on the display
as the phone dials it.
To end a call, place the handset on the
base or press TALK. The TALK and IN
USE indicators turn off.
REDIAL
Notes:
• If you press TALK to hang up and
the phone does not disconnect,
move closer to the base then press
TALK again, or place the handset on
the base.
Notes:
• The redial memory holds up to 32
digits, so you can redial long-
distance as well as local numbers.
14
Download from Www.Somanuals.com. All Manuals Search And Download.
43-1105.fm Page 15 Monday, August 30, 1999 1:57 PM
• We recommend you not use REDIAL
to dial numbers that include a tone
entry. This could result in a wrong
number being dialed. (See “Using
Tone Services on a Pulse Line.”)
3. When the service answers, press
. ✱ appears. Any additional num-
bers you dial are sent as tone sig-
nals.
4. After you complete the call, return
the handset to the base or press
TALK. The phone automatically re-
sets to pulse dialing.
• The redial memory does not store a
flash entry or any digits entered af-
ter you press FLASH (see “Using
Flash”).
USING PAGE
USING FLASH
To page the person who has the handset
or to locate the handset when the phone
is not in use, press PAGE on the base.
The handset beeps twice per second for
15 seconds and PAGINGappears. The
MESSAGE indicator flashes while the
handset beeps.
FLASH performs the electronic equiva-
lent of a switchhook operation for special
services, such as Call Waiting.
For example, if you have Call Waiting,
press FLASH to answer an incoming call
without disconnecting the current call.
Press FLASH again to return to the first
call.
PAGE
Note: If you do not have any special
phone services, pressing FLASH might
disconnect the current call.
To stop the handset from beeping before
it automatically stops, press any key on
the handset or PAGE on the base.
USING TONE SERVICES
ON A PULSE LINE
Note: You cannot page the handset dur-
Some special services, such as bank-by-
phone, require tone signals. If you have
pulse service, you can still use these
special tone services by following these
steps.
ing a call.
MEMORY DIALING
You can store up to 20 phone numbers in
memory, then dial a stored number by
pressing a two-digit memory location
number.
1. Be sure T/P is set to P.
2. Press TALK and dial the service’s
main number.
15
Download from Www.Somanuals.com. All Manuals Search And Download.
43-1105.fm Page 16 Monday, August 30, 1999 1:57 PM
Each stored number can be up to 16 dig-
its long.
If you enter an incorrect digit, start
from Step 1, then re-enter the cor-
rect digit.
3. Press MEM. ENTER 01-20 ap-
Storing a Number in Memory
pears.
Notes:
4. Enter a two-digit memory location
number between 05 and 20 (01–04
are reserved for your VIP Call List).
The ET-1105 beeps twice, and the
display becomes blank.
• If T/P is set to P and you want to use
tone dialing for a memory number,
you must store a
of the number you want to tone dial.
as the first entry
• Do not store a number with both
pulse and tone entries in the same
memory location. This could result
in a wrong number being dialed.
5. To keep a record of each stored
number, use a flat-blade screwdriver
to lift the plastic cover from the tele-
phone number index card. Write the
name on the index card.
• Each pause and tone entry (
uses one digit of memory.
)
Note: If you receive a call while you are
storing information in memory, press
TALK to answer the call. After the call,
begin again at Step 1.
• To keep your accounts secure, we
recommend you do not store your
personal access code for services
such as bank-by-phone in a memory
location.
To replace a stored number, store a new
one in its place.
• An error tone sounds and the phone
exits the programming mode if you
wait more than 30 seconds between
each keypress or enter more than
16 digits. You must start over at Step
1.
Using the VIP Call List
Your phone lets you save 4 phone num-
bers in the memory location numbers
01–04 as its VIP Call List. Whenever
someone calls from one of those 4 num-
bers, if you subscribe to Caller ID, the
1. Press MEM. MEMORY STORE
appears.
system sounds distinctive rings after the
VIP
first ring to alert you.
displays when
you recall the phone numbers (see “Re-
calling Numbers Stored in Memory” on
Page 17).
MEM
2. Enter the number you want to store.
The number appears on the display.
16
Download from Www.Somanuals.com. All Manuals Search And Download.
43-1105.fm Page 17 Monday, August 30, 1999 1:57 PM
Entering a Pause
Dialing a Memory Number
In some telephone systems, you must
dial an access code (9, for example) and
wait for a second dial tone before you
can dial an outside number. You can
store the access code with the phone
number. However, you should also store
a pause after the access code to allow
the outside line time to connect. To do
so, press REDIAL to enter a 2-second
pause after entering the access code. P
appears. For a longer pause, press RE-
DIAL again.
1. Press TALK. The TALK indicator
lights.
2. When you hear the dial tone, press
MEM then enter the 2-digit memory
location number. The ET-1105 auto-
matically dials the displayed phone
number.
Or, follow Step 2 in “Recalling Numbers
Stored in Memory” on Page 17 to recall
the desired phone number. Then press
CALLBACK.
Recalling Numbers Stored in
Memory
CALLBACK
1. Press CALL ID, then press #/
.
TOTAL MEM=xxdisplays.
Chain-Dialing Service Numbers
For quick recall of numbers for special
services (such as alternate long distance
or bank by phone), store each group of
numbers in its own memory location.
#/
When calling special services, dial the
service’s main number first. Then, at the
appropriate place in the call, press MEM
and enter the number for the location
where the additional information is
stored.
Note: If no phone number is stored,
MEM EMPTYdisplays.
2. Repeatedly press REVIEW ▲ or ▼
until the desired number appears.
17
Download from Www.Somanuals.com. All Manuals Search And Download.
43-1105.fm Page 18 Monday, August 30, 1999 1:57 PM
Testing Stored Emergency
Numbers
Deleting Information in All
Memory Locations
If you store an emergency service’s
number (police department, fire depart-
ment, ambulance) and you choose to
test the stored number, make the test
call during the late evening or early
morning hours to avoid peak demand pe-
riods. Remain on the line to explain the
reason for your call.
1. Press CALL ID, then press #/
.
TOTAL MEM=xxdisplays.
2. Press DELETE. DELETE ALL?ap-
pears.
3. Press DELETE again to confirm de-
letion. DELETE OKappears.
To exit without deleting all of the
memory location information, wait
10 seconds without pressing any
button.
Deleting Information in a Single
Memory Location
1. Recall the memory location contain-
ing the information you want to
delete.
2. Press DELETE. DELETE?appears.
DELETE
3. Press DELETE again to confirm de-
letion. The previous memory loca-
tion number and the number stored
there appear.
To exit without deleting the informa-
tion, wait 10 seconds without press-
ing any button.
18
Download from Www.Somanuals.com. All Manuals Search And Download.
43-1105.fm Page 19 Monday, August 30, 1999 1:57 PM
CALLER ID OPERATION
If you subscribe to Caller ID service from
your phone company, the ET-1105 auto-
matically displays the information the
phone company sends, along with the
date and time the call was received, be-
tween the first and second rings of every
call you receive. It stores up to 45 num-
ber only or name and number call
records in its Caller ID memory.
If you subscribe to your phone compa-
ny’s message waiting service, your sys-
tem informs you when you have a
message waiting. If the IN USE and
MESSAGE indicators on the base flash
(or
appears after you press TALK or
CALL ID on the handset), you have a
voice message in your mailbox. The IN
USE and MESSAGE indicators flash (or
appears after you press TALK or
CALL ID on the handset) until you re-
trieve the message.
The display also shows if caller informa-
tion is not available or if the number is
blocked by the sender (see “Caller ID
Displays” on Page 20).
The IN USE indicator flashes on the
base during an incoming call, RINGap-
pears briefly, the call record and NEWap-
pear for 10 seconds, then the display
blanks out.
If you subscribe to Call Waiting, the
MESSAGE indicator lights on the base
during a call. The Caller ID record ap-
pears. If you want to answer the incom-
ing call, press FLASH. To resume the
previous phone conversation, press
FLASH again.
REDIAL
19
Download from Www.Somanuals.com. All Manuals Search And Download.
43-1105.fm Page 20 Monday, August 30, 1999 1:57 PM
CALLER ID DISPLAYS
English
Display — French
Spanish
Description
xxNEWCID
TOTAL CID=xx
NOUV IDAP
The first line indicates the number of new calls. The sec-
ond line shows the total number of Caller ID records in
memory.
TOUT IDAP=xx
NUEV. ID.
TOTAL ID.=xx
ERROR
ERREUR
ERROR
Appears when the Caller ID information was garbled, or if
there was an error during the transmission.
PRIVATE
PRIVÉ
Appears if the caller chose to block sending Caller ID in-
formation. No caller information appears.
PRIVADO
UNAVAILABLE
NON DISPON.
NO DISPON.
Appears if the caller is not within a Caller ID service area,
or during operator-assisted calls or calls made with a
credit card.
Appears when you reach the end of your call records.
END OF LIST
FIN DE LISTE
FIN DE LISTA
Appears when there are no Caller ID records in memory.
NO CID MSG
PAS DE MESSIDAP
NING MENS ID
Appears when you review a Caller ID record from some-
one who has called more than one time from the same
number.
R#xx
20
Download from Www.Somanuals.com. All Manuals Search And Download.
43-1105.fm Page 21 Monday, August 30, 1999 1:57 PM
REVIEWING CALLER ID
RECORDS
DIALING NUMBERS FROM
A CALLER ID RECORD
1. Press CALL ID. xx NEW CID
1. Press CALL ID, then press REVIEW
▲ or ▼ until you see the phone
number you want to dial.
TOTAL CID=xx appears.
2. Press CALLBACK. The ET-1105 di-
CALL ID
als the displayed phone number.
If the phone number’s area code
does not match the stored area
code, the system automatically dials
a 1 before dialing the displayed area
code and 7-digit phone number.
(See “Setting the Area Code” on
Page 12.)
2. Repeatedly press REVIEW ▲ to see
more recent calls or REVIEW ▼ to
see older calls.
3. To see the Caller ID record number
and date/time, press
/
twice.
Note: If you do not press a button
within 10 seconds while you are re-
viewing Caller ID records, the ET-
1105’s display automatically blanks
out.
DELETING CALLER ID
RECORDS
The ET-1105 lets you delete individual
Caller ID records or all reviewed Caller
ID records at one time.
STORING CALLER ID
RECORDS IN A MEMORY
LOCATION
To delete a single Caller ID record:
1. Press CALL ID then repeatedly
press REVIEW ▲ or ▼ until the
record you want to delete appears.
1. Press CALL ID. xx NEW CID
2. Press DELETE. DELETE?appears.
TOTAL CID=xx appears.
3. Press DELETE again. DELETE OK
2. Repeatedly press REVIEW ▲ or ▼
until you see the desired Caller ID
record.
appears.
To delete all Caller ID records:
3. Press MEM twice, then enter the
memory location number. The ET-
1105 beeps and the phone number
is stored.
1. Press CALL ID then press DELETE.
DEL ALL OLD?appears.
2. Press DELETE. DELETE OK ap-
pears.
21
Download from Www.Somanuals.com. All Manuals Search And Download.
43-1105.fm Page 22 Monday, August 30, 1999 1:57 PM
TROUBLESHOOTING
We do not expect you to have any problems with your telephone, but if you do, the
following suggestions might help.
Problem
Suggestion
The handset does not work.
Move the handset closer to the base.
Be sure the phone line cord and AC adapt-
er are correctly and securely connected.
Be sure the battery pack is connected and
charged.
Raise the base’s antenna to a vertical po-
sition.
Return the handset to the base for 6 sec-
onds, then try again.
Volume drops or you hear unusual
sounds.
Someone has picked up another phone on
the same line. Hang up the other phone.
Call is noisy.
Do not place the base near appliances or
large metal objects.
Keep the handset away from interference
sources such as computers, remote con-
trol toys, wireless alarm systems, wireless
intercoms and room monitors, fluorescent
lights, and electrical appliances. If the in-
terference is severe, turn off the interfering
device.
Hang up and redial the number.
Phone dials more than 7 digits when
dialing a local phone number from a
Caller ID record.
Store the local area code (see “Setting the
Area Code” on Page 12).
The handset’s range decreases.
Raise the base’s antenna to a vertical po-
sition.
Return the handset to the base to re-
charge the battery pack.
Be sure the base’s antenna is not touching
a metal surface.
22
Download from Www.Somanuals.com. All Manuals Search And Download.
43-1105.fm Page 23 Monday, August 30, 1999 1:57 PM
Problem
Suggestion
Receiver sound flutters or fades.
Be sure the battery pack is charged.
Raise the base’s antenna to a vertical po-
sition.
Move the handset closer to the base.
Can receive calls, but cannot make
calls.
Set T/P correctly for the type of service you
have (see “Setting the Dialing Mode” on
Page 11).
If you still have problems, disconnect the phone. If other phones on the same line work
properly, the fault is in this phone or its installation. If you cannot find the problem, take
your ET-1105 to your local RadioShack store for assistance.
23
Download from Www.Somanuals.com. All Manuals Search And Download.
43-1105.fm Page 24 Monday, August 30, 1999 1:57 PM
OUT OF RANGE
INDICATIONS
If you move the ET-1105’s handset out of
the base’s range, OUT OF RANGEdis-
plays and the handset will not operate
properly.
If you move the handset out of the base’s
range when the handset is not in use, the
handset beeps twice every 16 seconds.
When you move the handset back within
range of the base again, OUT OF
RANGEdisappears.
If you move the handset out of the base’s
range while a call is in progress, two
beeps sound through the earpiece every
3-4 seconds, and you and the other party
cannot hear each other.
If you move the handset back within the
base’s range within 30 seconds, OUT
OF RANGEdisappears, and you can re-
sume your phone conversation.
If you keep the handset out of the base’s
range for 30 seconds or more, two beeps
sound through the earpiece every 4 sec-
onds. After 30 seconds, the call is dis-
connected, and the handset beeps twice
every 16 seconds. When you move the
handset back within range of the base
again, OUT OF RANGEdisappears.
24
Download from Www.Somanuals.com. All Manuals Search And Download.
43-1105.fm Page 25 Monday, August 30, 1999 1:57 PM
CARE AND MAINTENANCE
Your RadioShack ET-1105 Digital Spread Spectrum 900 MHz Cordless Telephone
is an example of superior design and craftsmanship. The following suggestions will
help you care for your phone so you can enjoy it for years.
Keep the phone dry. If it gets wet, wipe it dry immediately. Liquids
might contain minerals that can corrode the electronic circuits.
Use and store the phone only in normal temperature environments.
Temperature extremes can shorten the life of electronic devices, dam-
age batteries, and distort or melt plastic parts.
Keep the phone away from dust and dirt, which can cause premature
wear of parts.
Handle the phone gently and carefully. Dropping it can damage circuit
boards and cases and can cause the phone to work improperly.
Use only fresh batteries of the required size and recommended type.
Batteries can leak chemicals that damage your phone’s electronic
parts.
Wipe the phone with a damp cloth occasionally to keep it looking new.
Do not use harsh chemicals, cleaning solvents, or strong detergents to
clean the phone.
Modifying or tampering with the phone’s internal components can cause a malfunc-
tion and might invalidate its warranty and void your FCC authorization to operate it.
If your phone is not performing as it should, take it to your local RadioShack store
for assistance. If the trouble is affecting the telephone lines, the phone company
can ask you to disconnect your phone until you have resolved the problem.
25
Download from Www.Somanuals.com. All Manuals Search And Download.
43-1105.fm Page 26 Monday, August 30, 1999 1:57 PM
Cautions:
REPLACING THE
BATTERY PACK
• You must use a replacement battery
pack of the same size and type, with
the proper connector.
If you follow the instructions in “Connect-
ing and Charging the Battery Pack” on
Page 9, the battery pack should last
about one year. If the battery does not
hold a charge for more than 2 hours after
an overnight charge, replace the battery
with a new 3.6 volt, 600 milliamp battery
with a connector that fits the socket in the
battery compartment. You can order a
replacement battery pack through your
local RadioShack store.
• Do not dispose of the battery pack
in a fire because it might explode.
• Do not open or mutilate the battery
pack.
• Be careful not to short the battery
pack by touching it with conducting
materials, such as rings, bracelets,
and keys. The battery pack or con-
ductor might overheat and burn.
Install the new battery pack as described
below, then charge the battery pack for
about 15 hours (see “Connecting and
Charging the Battery Pack” on Page 9).
If you have trouble replacing the battery
pack, take the phone to your local Ra-
dioShack store for assistance.
Note: To avoid losing information stored
in memory, try to install and begin charg-
ing the new battery pack within 2–3 min-
utes.
Important: This phone
can use nickel-cadmium
rechargeable batteries.
At the end of a nickel-
cadmium battery's useful
life, it must be recycled or
0
0
8
3
4
1. Press down and slide off the cover.
disposed of properly. Contact your local,
county, or state hazardous waste man-
agement authorities for information on
recycling or disposal programs in your
area or call 1-800-843-7422. Some op-
tions that might be available are: munici-
pal curbside collection, drop-off boxes at
retailers such as your local RadioShack
store, recycling collection centers, and
mail-back programs.
2. Gently pull on the battery pack con-
nector to disconnect it, then remove
the battery pack.
3. Plug the new battery pack’s connec-
tor into the socket and place the bat-
tery pack into the compartment.
4. Replace the cover.
26
Download from Www.Somanuals.com. All Manuals Search And Download.
43-1105.fm Page 27 Monday, August 30, 1999 1:57 PM
If you cannot eliminate the interference,
the FCC requires that you stop using
your phone.
THE FCC WANTS YOU TO
KNOW
In the unlikely event that your phone
causes problems on the phone line, the
phone company can temporarily discon-
tinue your service. If this happens, the
phone company attempts to notify you in
advance. If advance notice is not practi-
cal, the phone company notifies you as
soon as possible and advises you of your
right to file a complaint with the FCC.
Some cordless telephones operate on
frequencies that may cause interference
to nearby TVs and VCRs. To minimize or
prevent such interference, the base of
the cordless telephone should not be
placed near or on top of a TV or VCR.
LIGHTNING
Also, the phone company can make
changes to its lines, equipment, opera-
tions, or procedures that could affect the
operation of this telephone. The tele-
phone company notifies you of these
changes in advance, so you can take the
necessary steps to prevent interruption
of your telephone service.
Your telephone has built-in lightning pro-
tection to reduce the risk of damage from
surges in telephone line and power line
current. This lightning protection meets
or exceeds FCC requirements. However,
lightning striking the telephone or power
lines can damage your telephone.
Lightning damage is not common. Nev-
ertheless, if you live an area that has se-
vere electrical storms, we suggest that
you unplug your phone during storms to
reduce the possibility of damage.
Your phone might cause TV or radio in-
terference even when it is operating
properly. To determine whether your
phone is causing the interference, turn
off your phone. If the interference goes
away, your phone is causing the interfer-
ence. Try to eliminate the interference
by:
• Moving your phone away from the
receiver
• Connecting your phone to an AC
outlet that is on a different electrical
circuit from the receiver
• Contacting your local RadioShack
store for help
27
Download from Www.Somanuals.com. All Manuals Search And Download.
43-1105.fm Page 28 Monday, August 30, 1999 1:57 PM
Limited One-Year Warranty
This product is warranted by RadioShack against manufacturing defects in material and workman-
ship under normal use for one (1) year from the date of purchase from RadioShack company-owned
stores and authorized RadioShack franchisees and dealers. EXCEPT AS PROVIDED HEREIN, Ra-
dioShack MAKES NO EXPRESS WARRANTIES AND ANY IMPLIED WARRANTIES, INCLUDING
THOSE OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE, ARE LIMITED
IN DURATION TO THE DURATION OF THE WRITTEN LIMITED WARRANTIES CONTAINED
HEREIN. EXCEPT AS PROVIDED HEREIN, RadioShack SHALL HAVE NO LIABILITY OR RE-
SPONSIBILITY TO CUSTOMER OR ANY OTHER PERSON OR ENTITY WITH RESPECT TO ANY
LIABILITY, LOSS OR DAMAGE CAUSED DIRECTLY OR INDIRECTLY BY USE OR PERFOR-
MANCE OF THE PRODUCT OR ARISING OUT OF ANY BREACH OF THIS WARRANTY, IN-
CLUDING, BUT NOT LIMITED TO, ANY DAMAGES RESULTING FROM INCONVENIENCE, LOSS
OF TIME, DATA, PROPERTY, REVENUE, OR PROFIT OR ANY INDIRECT, SPECIAL, INCIDEN-
TAL, OR CONSEQUENTIAL DAMAGES, EVEN IF RadioShack HAS BEEN ADVISED OF THE
POSSIBILITY OF SUCH DAMAGES.
Some states do not allow the limitations on how long an implied warranty lasts or the exclusion of in-
cidental or consequential damages, so the above limitations or exclusions may not apply to you.
In the event of a product defect during the warranty period, take the product and the RadioShack
sales receipt as proof of purchase date to any RadioShack store. RadioShack will, at its option, un-
less otherwise provided by law: (a) correct the defect by product repair without charge for parts and
labor; (b) replace the product with one of the same or similar design; or (c) refund the purchase
price. All replaced parts and products, and products on which a refund is made, become the prop-
erty of RadioShack. New or reconditioned parts and products may be used in the performance of
warranty service. Repaired or replaced parts and products are warranted for the remainder of the
original warranty period. You will be charged for repair or replacement of the product made after the
expiration of the warranty period.
This warranty does not cover: (a) damage or failure caused by or attributable to acts of God, abuse,
accident, misuse, improper or abnormal usage, failure to follow instructions, improper installation or
maintenance, alteration, lightning or other incidence of excess voltage or current; (b) any repairs
other than those provided by a RadioShack Authorized Service Facility; (c) consumables such as
fuses or batteries; (d) cosmetic damage; (e) transportation, shipping or insurance costs; or (f) costs
of product removal, installation, set-up service adjustment or reinstallation.
This warranty gives you specific legal rights, and you may also have other rights which vary from
state to state.
RadioShack Customer Relations, 200 Taylor Street, 6th Floor, Fort Worth, TX 76102
04/99
We Service What We Sell
RadioShack
A Division of Tandy Corporation
Fort Worth, Texas 76102
08A99
Printed in China
Download from Www.Somanuals.com. All Manuals Search And Download.
|