Radio Shack Cordless Telephone 43 5560 User Guide

5.8 GHz Multi-Handset Expandable

Cordless Telephone

with Call Waiting / Caller ID

43-5560

Hearing-Aid Compatible — Enables use of the phone

with hearing aids that have a T (telephone) switch.

Ample Talk and Standby Time — The supplied battery

(when fully charged) provides about five hours of talk

time or seven days of standby time.

Distinctive Ring — Allows you to assign a distinctive

ringer to certain memory locations. When an incoming

call is received and the Caller ID information matches the

information in one of the memory locations, the

distinctive ring that has been stored for that particular

caller sounds. (See “Distinctive Ringer Setup” on

page 18)

Speakerphone — lets you conduct a hands-free

conversation using the handset speaker. (See “Making

and Receiving Calls” on page 25)

Convenient Extension Placement — lets you place

accessory handsets (up to ten total) anywhere you have

an AC outlet, regardless of phone jack location.

Call Waiting/Caller ID — lets you answer a call even

when you’re on the phone and see who’s calling before

you answer.

DirectLink Mode — lets you use two handsets like

walkie-talkies, even if you are away from base unit. (See

“Using the DirectLink Mode” on page 44)

IMPORTANT

If an icon appears at the end of a paragraph, go to the box on that page with the

corresponding icon for pertinent information.

— Warning

— Important ꢀ — Caution Ô — Note

OWNER’S MANUAL

Please read before using this equipment.

RadioShack and RadioShack.com are trademarks

used by RadioShack Corporation.

ENERGYSTAR and the ENERGYSTAR certification mark

are registered US marks.

DirectLink is a registered trademark of Uniden Corporation.

Download from Www.Somanuals.com. All Manuals Search And Download.

INTRODUCTION

Thank you for purchasing a RadioShack 5.8

GHz Multi Handset Expandable Cordless

Telephone. Unlike other conventional

cordless telephones, your telephone

supports up to ten handsets on a single

telephone line. You can add a handset to

any room in your home or office that has an

AC outlet. No more running to the other end

of the house to answer the phone! You can

transfer outside calls to other handsets. If

you subscribe to Call Waiting with Caller ID,

the phone shows you the incoming caller

information, even when you are already

talking on the phone.

Cordless phones require AC power to

operate. When the power is off, you cannot

make or receive calls by using your phone.

You should also have a phone that does not

need AC power to operate (not a cordless

phone), so you can still make and receive

calls if there is an AC power failure.

WHAT’S INCLUDED

Make sure you have received the following

items in the package.

• Base unit (1)

• Handsets (2)

• Charger (1)

• AC adapters (2)

• Telephone cord (1)

• Rechargeable batteries (2)

• Belt clips (2)

• Wall mount Adapter (1)

• Printed Materials

Download from Www.Somanuals.com. All Manuals Search And Download.

IMPORTANT

•

Your phone operates on

standard radio

frequencies as allocated

by the FCC.

INFORMATION

This telephone has been tested and found

to comply with all applicable UL and FCC

standards.

It is possible for other

radio units operating

nearby on similar

FCC STATEMENT

This equipment complies with Part 68 of the

FCC rules and the requirements adopted by the

ACTA. On the base of this equipment is a label

that contains, among other information, a

product identifier in the format

frequencies to

unintentionally intercept

your conversation or

cause interference. This

possible lack of privacy

can occur with any

cordless phone.

US:AAAEQ##TXXXX. If requested, this number

must be provided to the telephone company.

Your phone is not intended to be used with

party-line systems. Connection to party line

service is subject to state tariffs. Contact the

state public utility commission, public

service commission, or corporation

commission for information. Ô

The REN is used to determine the number of

devices that may be connected to a telephone

line. Excessive RENs on a telephone line may

result in the devices not ringing in response to

an incoming call. In most but not all areas, the

sum of RENs should not exceed five (5.0). To

be certain of the number of devices that may

be connected to a line, as determined by the

total RENs, contact the local telephone

As an ENERGYSTAR Partner,

RadioShack Corporation has

determined that this product

meets the ENERGYSTAR

guidelines for energy

efficiency.

company. For products approved after July

23, 2001, the REN for this product is part of

the product identifier that has the format

US:AAAEQ##TXXXX. The digits represented

by ## are the REN without a decimal point

(e.g., 03 is a REN of 0.3). For earlier products,

the REN is separately shown on the label.

If you use more than one phone or other

device on the line, add up all of the RENs. If

the total is more than five (three in rural

areas), your telephones might not ring. If

ringer operation is impaired, remove a

device from the line.

Ô NOTE Ô

You must not connect your

phone to:

•

coin-operated systems

most electronic key

telephone systems

CAUTION: TO REDUCE THE RISK OF ELECTRIC

WARNING: To reduce the risk of

fire or shock hazard, do not expose

this product to rain or moisture.

CAUTION

SHOCK, DO NOT REMOVE COVER OR BACK. NO USER-

SERVICEABLE PARTS INSIDE. REFER SERVICING TO

QUALIFIED PERSONNEL.

RISK OF ELECTRIC

SHOCK DO NOT OPEN

The lightning symbol is intended to alert you to the presence of

uninsulated dangerous voltage within this product’s enclosure that

might be of sufficient magnitude to constitute a risk of electric shock.

Do not open the product’s case.

The exclamation symbol is intended to inform you that important operating

and maintenance instructions are included in the literature accompanying

this product.

Download from Www.Somanuals.com. All Manuals Search And Download.

In the unlikely event that your phone causes

problems on the phone line, the phone company

can temporarily discontinue your service. If this

happens, the phone company attempts to notify

you in advance. If advance notice is not

practical, the phone company notifies you as

soon as possible and advises you of your right to

file a complaint with the FCC.

Also, the phone company can make changes

to its lines, equipment, operations, or

procedures that could affect the operation of

this phone. The telephone company notifies

you of these changes in advance, so you can

take the necessary steps to prevent

interruption of your telephone service.

This device complies with part 15 of the FCC

rules. Operation is subject to the following two

conditions: (1) This device may not cause

harmful interference, and (2) This device must

accept any interference received, including

interference that may cause undesired

operation. Privacy of communications, may

not be ensured when using this phone.

To insure the safety of users, the FCC has

established criteria for the amount of radio

frequency energy various products may

produce depending on their intended usage.

This product has been tested and found to

comply with the FCC’s exposure criteria. For

body worn operation, the FCC RF exposure

guidelines were also met when used with the

RadioShack accessories supplied or designed

for this product. Use of other accessories may

not ensure compliance with FCC RF exposure

guidelines and should be avoided.

SURGE PROTECTION

Your telephone has built-in protection

circuits to reduce the risk of damage from

surges in telephone line and power line

current. These protection circuits meet or

exceed the FCC requirements. However,

lightning striking the telephone or power

lines can damage your telephone.

Lightning damage is not common.

Nevertheless, if you live in an area that has

severe electrical storms, we suggest that you

unplug your phone when storms approach to

reduce the possibility of damage.

Download from Www.Somanuals.com. All Manuals Search And Download.

IMPORTANT SAFETY INSTRUCTIONS

When using your telephone equipment, basic safety precautions should

always be followed to reduce the risk of fire, electric shock and injury to

persons, including the following:

1. Do not use this product near water, for example, near a bathtub,

wash bowl, kitchen sink, or laundry tub, in a wet basement or near a

swimming pool.

2. Avoid using a telephone (other than a cordless type) during an

electrical storm. There may be a remote risk of electric shock from

lightning.

3. Do not use the telephone to report a gas leak in the vicinity of the

leak.

4. Use only the power cord and batteries indicated in this manual.

Do not dispose of batteries in a fire. They may explode. Check with

local codes for possible special disposal instructions.

SAVE THESE INSTRUCTIONS

Download from Www.Somanuals.com. All Manuals Search And Download.

IMPORTANT CALLER

ID INFORMATION

To use Caller ID and Call Waiting, you must

be in an area where those services are

available and you must subscribe to those

services through your local phone company.

Where Caller ID is offered, one or more

options are generally available:

• caller’s number only

• caller’s name only

• caller’s name and number

If you subscribe to Call Waiting ID and

Caller ID, the system can show you the

incoming caller information, even when you

are already talking on the phone.

READ THIS BEFORE

INSTALLATION

We have designed your phone to conform

to federal regulations and you can connect it

to most phone lines. However, each device

that you connect to the telephone line draws

power from the line. We refer to this power

draw as the phone’s ringer equivalence

number, or REN. The REN is on the bottom

of your phone.

If you use more than one phone or other

device on the line, add up all the RENs. If

the total is more than five (three in rural

areas), your phones might not ring. If ringer

operation is impaired, remove one of the

devices from the line.

Download from Www.Somanuals.com. All Manuals Search And Download.

INSTALLATION

Ô NOTE Ô

Before using your phone, carefully peel the

protective film off the display. The film

protects the handset window during

shipment and is not necessary to any phone

function.

If your home has specially

wired alarm equipment

connected to the telephone

line, be sure that installing

the system does not disable

your alarm equipment.

If you have questions about

what will disable alarm

equipment, contact your

telephone company or a

qualified installer.

SELECTING A LOCATION

You can place the phone’s base on a desk

or table, or mount it on a standard wall plate

or directly on a wall. Select a location that

is:Ô

• near an accessible AC outlet

• near a telephone line jack

• out of the way of normal activities

• away from electrical machinery,

electrical appliances, metal walls or

filing cabinets, wireless intercoms,

alarms, and room monitors

• away from other cordless phones

The base’s location affects the handset’s

range. If you have a choice of several

locations, try each to see which provides the

best performance.

The handset antenna is located on the

back, above the ringer speaker. For

maximum communication range, do not

hold the handset in such a way as to cover

the antenna by your hand. Also, place the

handset in the upright position while not in

use so the antenna can pick up the signals

from the base.

Correct

When there is obstacle such as metal or

concrete wall between the handset and the

base, the operation might be affected. Try to

keep free from obstruction.

Incorrect

Download from Www.Somanuals.com. All Manuals Search And Download.

Your telephone connects directly to a

modular telephone line jack. If your

telephone wiring does not have a modular

jack, you can update the wiring yourself

using jacks and adapters (available at your

local RadioShack store), or have the

telephone company update the wiring for

you. You must use compatible modular

jacks that are compliant with Part 68 of FCC

Rules. Ô

Ô NOTE Ô

The USOC number of the

jack to be installed is

RJ11C (or RJ11W for a wall

plate jack).

On a Desk Top

1. Plug one end of the supplied long

modular cord into the TEL LINE jack on

the back of the base.

2. Plug the modular cord’s other end into

a modular phone line jack.

3. Insert the supplied AC adapter’s barrel

plug into the DC IN 9V jack on the back

of the base. ꢀ

ꢀ

CAUTION

ꢀ

You must use

a Class 2

power source

4. Route the adapter’s cord through the

strain relief slot on the base, then plug

the adapter into a standard AC outlet.

that supplies 9V DC and

delivers at least 350mA.

Its center tip must be set

to positive and its plug

must fit the phone’s DC

IN 9V jack. The supplied

adapter meets these

specifications. Using an

adapter that does not

meet these

On a Wall Plate or Wall

To mount the phone directly on a wall, you

need two screws (not supplied) with heads

that fit into the keyhole slots on the bracket.

Drill two holes 3¹⁵/₁₆inches apart. Thread a

screw into each hole, letting the heads

extend about ¹/₈inch.

specifications could

damage the phone or

the adapter.

1. Make the AC adapter and the short

telephone line cord through the hole on

the bracket.

2. Slide the bracket into the notches on

the base.

3. Plug the adapter into a standard AC

outlet. Hook the cord on the notch of

the bracket.

Download from Www.Somanuals.com. All Manuals Search And Download.

4. Plug the telephone line cord into the

telephone outlet.

5. For a wall plate,

align the base’s

keyhole slots

with the wall

plate studs and

slide the base

downward to secure it.

For direct wall

mounting, align

the base’s

To remove, push up

a tab on the wall

mount adapter as

shown.

keyhole slots with

the mounting

screws and slide

the base downward to secure it.

CONNECTING/CHARGING THE

BATTERY PACK

The phone comes with a rechargeable

nickel-metal hydride (Ni-MH) battery pack.

Before using your phone, you must charge it

for about 15–20 hours.

1. Press down and slide off the battery

compartment cover.

2. Lift the battery pack out of the

compartment.

3. Plug the battery pack’s connector into

the socket in the compartment (the

connector fits only one way), then place

the battery pack in the compartment.

4. Replace the cover.

To charge the battery pack, place the

handset on the base. The CHARGE indicator

on the base lights.

Recharge the battery pack when

Low Batteryflashes on the display.

Download from Www.Somanuals.com. All Manuals Search And Download.

If you have trouble replacing the battery

pack, take the phone to your local

RadioShack for assistance.

Recharging the Battery Pack

• If the battery pack becomes weak

during a call, Low Batteryflashes.

When this happens, you cannot make a

call until you recharge the battery

IMPORTANT

Be sure the battery pack is

properly connected before

you try to charge it. The

CHARGE indicator lights

when the handset is on the

base, even if the battery

pack is not connected.

pack.

• If the display is blank and the phone

does not work, recharge the battery

pack. (The battery power might be too

low to light the display.)

• About once a month, fully discharge the

battery by keeping the handset off the

base until Low Batteryflashes on

the display. Otherwise, the battery pack

loses its ability to fully recharge.

• Using a damp cloth, clean the charging

contacts on the handset about once a

month.

• If you are not going to use your phone

for an extended period, disconnect the

battery pack. This increases the battery

pack’s usable life.

• The supplied battery pack should last

for about a year. If the battery pack

does not hold a charge for more than 2

hours after an overnight charge,

replace it with a new 3.6-volt, 800 mAh

battery pack with a connector that fits

the socket in the battery compartment.

You can order a replacement battery

pack through RadioShack. Install the

new battery pack and charge it for

WARNING

Dispose of the old battery

pack promptly and properly.

Do not burn or bury it.

There is a risk of explosion

if battery is replaced by an

incorrect type. Dispose of

used batteries according to

the instructions.

^{about 15–20 hours.}o

Download from Www.Somanuals.com. All Manuals Search And Download.

INSTALLING A BELTCLIP

To attach the beltclip

Insert the beltclip into the holes on each

side of the handset. Press down until it

clicks.

To remove the beltclip

Pull either side of the beltclip to release the

tabs from the holes.

USING A HEADSET

You can make or answer calls with hands-

free convenience using an optional headset

that has a ³/32-inch (2.5-mm) plug.

RadioShack has a variety of headsets

available.

To connect the headset, gently flip open the

rubber headset jack cover on the side of the

handset, then insert the headset’s plug into

the jack. Ô

Ô NOTES Ô

Connecting a headset disconnects the

handset’s earpiece and microphone.

•

If you place the handset

on the base to recharge

it while the headset is

connected, be sure the

handset seats properly.

VOL/RING/ or VOL/RING/ on the handset

also controls the headset’s volume.

With a headset connected, you can make or

answer calls as usual using the keys on the

handset.

You can use a handset

holder (available from

your local RadioShack

store) to hang the

handset on your belt for

greater convenience

when using a headset.

When you finish using the headset,

disconnect it from the handset and close the

rubber cover to protect the jack.

Download from Www.Somanuals.com. All Manuals Search And Download.

DISPLAY AND ICONS

Example of the standby mode display

Ringer off icon (when the ringer is off)/ day of the week and

time / battery icon

ꢀꢀꢀ570ꢀꢁꢂꢃꢄꢄ#ꢀ

ꢀꢀꢀ*CPFUGVꢀꢅꢁ

ꢀꢀ0GYꢀ%+&ꢃꢀꢀꢆ

Handset ID and Banner

Number of new Caller ID calls received (If there are no new Caller

ID messages, the Handset ID appears here.)

4'&+#.

/'07

Appears

During

ICON

DESCRIPTION

Battery icons indicate the handset battery status. This

icon changes depending on the battery status (empty,

low, medium and full).

Standby/

Talk

Standby

Talk

The Ringer off icon indicates that ringer is turned off.

The Mute icon appears when you mute the handset.

The Speaker icon appears when the handset speaker

phone is used.

Talk

The Privacy icon appears when the Privacy Mode is

turned on.

ANIMATION DISPLAYS

The handsets have a variety of animation displays. Below are examples

of the animation screens and what they mean:

Turning on the phone

Hanging up the phone Confirmation (Done!)

Deleting (Deleted!)

ꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢁꢂꢃꢄ

ꢀꢀꢀ9GNEQOGꢁ

ꢀꢀꢀꢀꢀꢀ'PF

ꢀꢀꢀꢀꢀꢀ&QPGꢁ

ꢀꢀꢀꢀ&GNGVGFꢁ

ꢀ2NGCUGꢀ9CKVꢂꢂꢂ

4'&+#.

/'07

Making a call

Find Handset/Paging

the Handset

ꢀ6CNM

ꢀꢀꢀꢀꢀ2CIKPI

ꢀꢀꢀꢀꢀꢀꢀꢀꢀꢁꢂꢃꢄ

/76'

%9&:

24+8#%;

Also, the animation display changes depending on the ringer volume setting.

ꢀ4KPIGTꢀ8QNWOG

4'&+#.

/'07

4'&+#.

/'07

4'&+#.

/'07

Out of Range

Unavailable

Low Battery

ꢀꢀ1WVꢀ1Hꢀ4CPIG

ꢀꢀ7PCXCKNCDNG

ꢀꢀ.QYꢀ$CVVGT[

4'&+#.

/'07

4'&+#.

/'07

Download from Www.Somanuals.com. All Manuals Search And Download.

SOFT KEY FUNCTION

“Soft” keys are keys that change function

during the operation of the phone. There are

three soft keys on each handset. Soft Keys

allow you to:

Ô NOTES Ô

The soft keys will not

appear while the

•

handset is charging.

• Access the main menu

• Set up CIDCW options

• Store or edit phone numbers

Standby Mode - The

handset is not in use and

talk/FLASH has not

been pressed.

• Redial one of the last three numbers

dialed from the handset

• Access voice mail waiting

The function of each soft key is determined

by the icon that appears directly above it.

For example, when the handset is in

standby mode, pressing soft key 1 will redial

the last dialed number. When the handset is

in talk mode, pressing soft key 1 will mute

the microphone. Ô

Complete information on the features

controlled by the soft keys can be found

under each feature.

In standby mode

ꢀꢀꢀ570ꢀꢁꢂꢃꢄꢄ#ꢀ

ꢀꢀꢀ*CPFUGVꢀꢅꢁ

ꢀꢀ0GYꢀ%+&ꢃꢀꢀꢆ

4'&+#.

/'07

Soft key 1 Soft key 2 Soft key 3

In talk mode

6CNM

ꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢁꢂꢁꢁ

24+8#%;

/76'

%9&:

Soft key 1 Soft key 2 Soft key 3

Download from Www.Somanuals.com. All Manuals Search And Download.

MAIN MENU

OPTIONS

Your phone has five main menu options:

DirectLink Mode, Room/Baby Monitor,

Handset Setup, Global Setup and Deregister

HS. Ô

Ô NOTES Ô

•

For Global Setup and

Deregister HS menu

options, make sure the

line is not in use and the

handsets are within

range of the base.

DEFAULT SETTINGS

The default settings set from the factory

match the features that most people use.

You may not need to change them.

However, there are a number of options you

must set and entries you must make in

memory to take full advantage of all the

phone features. The table below lists the

default settings.

Main menu flow chart is

provided on page 52.

Function

Default Settings

Edit Voice Mail

Ringer Tones

Distinctive Ring

Auto Talk

None

Flicker

Off

Anykey Answer

Banner

Off

“ “

Language

English

Contrast

level 5

Key Touch Tone

Animation Screen

Day & Time

CIDCW

SUN 12:00 AM

CW On /CWDX Off

None

Area Code

Dial Mode

Tone

Voice Mail Tone

Download from Www.Somanuals.com. All Manuals Search And Download.

SETTING MENU

OPTIONS

USING THE INTERFACE

Below are some tips for using the software

interface on your phone.

• Press the MENU soft key to access the

main menu.

• Use VOL/RING/ or VOL/RING/ to

scroll through options.

• Press the OK soft key to make a

selection.

• Press the BACK soft key to return to the

previous screen.

• Press end to exit the menu.

DirectLink Mode

In DirectLink® mode, a pair of handsets can

function as two-way radios. DirectLink Mode

allows two handsets to communicate with

each other without the base unit or a

telephone line. Use them at sporting events

or while shopping to stay in contact with

family members or friends. You must set

both handsets to DirectLink Mode to

activate this feature. For detailed operation

instruction, refer to “Using the DirectLink

Mode” on page 44. Ô

Ô NOTE Ô

You must have at least two

handsets to use Direct Link

Mode.

Download from Www.Somanuals.com. All Manuals Search And Download.

Room/Baby Monitor

This feature allows you to monitor sounds in

another room. Place the handset in the

room you wish to monitor; it will function as

a microphone. A second handset can be set

to function as a remote speaker, allowing

you to monitor sounds in the room. Ô

Ô NOTE Ô

This feature only works

when the handset(s) is

within the range of the

base.

Using Room/Baby Monitor

1. Press the MENU soft key and select the

Room Monitor menu. To Room

Monitorappears.

2. Select the handset you want to monitor

by using VOL/RING/ or VOL/RING/

3. Press the OK soft key.

RoomMonitorappears, and you hear

sounds in the room where the handset

is installed.

4. To turn off the Room Monitor, press the

END soft key, or end.

Handset Setup

The following submenu options must be set

separately for each handset.

Programming your Voice Mail

Access Number

1. Press the MENU soft key. Select the

Handset Setup menu, and then the Edit

Voice Mail submenu. Edit V_mail

No.appears.

2. Enter your personal access number

using the number keypad (0-9),

/tone/<, #/>, the DELETE soft key, or

the PAUSE soft key (up to 20 digits).

3. Press the OK soft key. You will hear the

confirmation tone.

To delete the current Voice Mail Access

Number, delete all numbers in Step 2 using

the DELETE soft key and the OK soft key.

Download from Www.Somanuals.com. All Manuals Search And Download.

Selecting a Ringer Tone

Ringer Tone lets you choose from ten ringer

tones or ten melodies:

• Ringers (Flicker, Clatter, Soft Alert,

Wake Up, Light Bug, Beep Boop, Tone

Board, Chip Chop, Party Clap,

Reminder)

• Melodies (Beethoven’s Symphony #9

[Beethoven9], For Elise [Elise], We

Wish You A Merry Christmas [Merry-

Xmas], Home Sweet Home [Hm Swt

Hm], Lorri Song #6 [Lorri Song], When

Irish Eyes Are Smiling [Irish Eyes],

Aura Lee, Let Me Call You Sweet Heart

[Sweetheart], Star Spangled Banner

[Star Spngl], Old MacDonald [Old

MacDld])

You must set a separate ringer tone on

each handset.

1. Press the MENU soft key. Select the

Handset Setup menu, and then the

Ringer Tones submenu.

2. Press VOL/RING/ or VOL/RING/ to

move the pointer. You will hear the

ringer or melody as you scroll through

the options.

3. When you reach the ringer tone you

want, press the OK soft key. You will

hear a confirmation tone.

Distinctive Ringer Setup

Distinctive Ringer allows you to assign a

designated ring tone to a stored phonebook

number (100 stored locations available).

When a call is received and the Caller ID

information matches the information in one

of the phonebook memory locations, the

phone uses the distinctive ring assigned to

that particular caller. You can assign

distinctive rings to multiple phonebook

Download from Www.Somanuals.com. All Manuals Search And Download.

memory locations. Switching the setting to

Distinctive Ring Off disables distinctive

ringing: all incoming calls will have a normal

ring tone. Switching to Distinctive Ring On

activates all programmed distinctive ring

memory locations.

1. Press the MENU soft key. Select the

Handset Setup menu, and then the

Distinctive Ring submenu.

2. Press VOL/RING/ or VOL/RING/ to

select Onor Off.

3. Press the OK soft key. You will hear a

confirmation tone.

Setting the Auto Talk

Autotalk allows you to answer the phone

simply by removing the handset from the

cradle. You do not have to press any keys

to answer the call.

1. Press the MENU soft key. Select the

Handset Setup menu and then the Auto

Talk submenu.

2. Press VOL/RING/ or VOL/RING/ to

select Onor Off.

3. Press the OK soft key. You will hear a

confirmation tone.

Setting the Anykey Answer

Any Key Answer allows you to answer the

phone by pressing any number key,

/tone/<, or #/> on the handset.

1. Press the MENU soft key. Select the

Handset Setup menu, and then the

Anykey Answer submenu.

2. Press VOL/RING/ or VOL/RING/ to

select Onor Off.

3. Press the OK soft key. You will hear a

confirmation tone.

Download from Www.Somanuals.com. All Manuals Search And Download.

Setting the True Banner

True Banner lets you customize the name

your handset displays.

The name will be displayed on the LCD

screen during Standby Mode, Intercom,

Intercom Hold, Room Monitor and Copy

Phonebook operation. The banner name

will be displayed on the receiving handset

as well.

1. Press the MENU soft key. Select the

Handset Setup menu, and then the

Banner submenu.

2. Use the number keypad (0-9),

/tone/<, #/>, or the DELETE soft key to

enter or edit the name.

3. Press the OK soft key. You will hear a

confirmation tone.

Selecting a Language

Language selects which language the menu

display will use. Choose from English,

French, or Spanish.

1. Press the MENU soft key. Select the

Handset Setup menu, and then the

Language submenu.

2. Press VOL/RING/ or VOL/RING/ to

choose “English”, “Français” (French),

or “Español” (Spanish).

3. Press the OK soft key. You will hear a

confirmation tone.

Adjusting the LCD Contrast

Contrast adjusts the handset LCD

brightness. Choose one of the 10 levels for

optimum viewing.

1. Press the MENU soft key. Select the

Handset Setup menu and then the

Contrast submenu.

Download from Www.Somanuals.com. All Manuals Search And Download.

2. Press VOL/RING/ or VOL/RING/ to

adjust the contrast of the LCD (10

levels).

3. Press the OK soft key. You will hear a

confirmation tone.

Setting the Key Touch Tone

Key Touch Tone is the tone your keypad

makes when keys are pressed. You can

turn this tone on or off.

1. Press the MENU soft key. Select the

Handset Setup menu and then the Key

Touch Tone submenu.

2. Press VOL/RING/ or VOL/RING/ to

select Onor Off.

3. Press the OK soft key. You will hear a

confirmation tone.

Setting the Animation Screen

The Animation screen displays animations

on the handset LCD. The animations will be

displayed on the LCD screen during a call,

ringer volume setting, when you hang up,

and during other functions.

See “Animation Displays” on page 13 for all

the available screens.

1. Press the MENU soft key. Select the

Handset Setup menu and then the

Animation Screen submenu.

2. Press VOL/RING/ or VOL/RING/ to

select Onor Off.

3. Press the OK soft key. You will hear a

confirmation tone.

Global Setup

Ô NOTE Ô

For setting the Day and

Time, the time-out is

If you change one of the global settings, you

change that setting for all registered

handsets. Only one handset can change

global settings at a time. Ô

extended to two minutes.

Download from Www.Somanuals.com. All Manuals Search And Download.

Setting Day and Time

Day & Time sets the day and time of your

display.

1. Press the MENU soft key. Select the

Global Setup menu, and then the Day

& Time submenu option.

2. Press VOL/RING/ or VOL/RING/ to

select the day of the week, and then

the

soft key.

3. Press VOL/RING/ or VOL/RING/ to

set hour, and then press the

key.

soft

4. Press VOL/RING/ or VOL/RING/ to

set minute, and then press the

key.

soft

5. Press VOL/RING/ or VOL/RING/ to

choose AMor PM, and then press the

SAVE soft key. You will hear a

confirmation tone.

Setting CIDCW (Caller ID on

Call Waiting)

Caller ID on Call Waiting (CIDCW) displays

the name and number of an incoming call

while you are on the line. Call Waiting

Deluxe (CWDX) allows you to handle call

waiting calls in seven different ways.

1. Press the MENU soft key. Select the

Global Setup menu, and then the

CIDCW submenu.

2. Press VOL/RING/ or VOL/RING/ to

select CW On/CWDX On, CW On/CWDX

Off, or CW Off/CWDX Off, and then

press the OK soft key. You will hear a

confirmation tone.

Download from Www.Somanuals.com. All Manuals Search And Download.

Setting the Area Code

If you enter a 3-digit area code number in

the “Area Code” option, your local area

code does not appear in the Caller ID

message. For calls received from outside

your local area code, you will see a full 10-

digit number. Ô

Ô NOTES Ô

•

If your calling area

requires 10-digit dialing,

do not program this

option.

If the area code has

already been stored in

memory, the stored area

code will be displayed.

To change it, use the

DELETE soft key and

number keys to enter the

new area code.

1. Press the MENU soft key. Select the

Global Setup menu, and then the Area

Code submenu.

2. Press the number keypad (0-9) to enter

a 3-digit area code.

3. Press the OK soft key. You will hear a

confirmation tone.

Setting the Dial Mode

Sets the dial mode to tone or pulse. Most

phone systems use tone dialing; the default

setting is tone dialing. Set the dialing mode

to match the dialing system used by your

local phone service.

• If you are not sure of your dialing

system, set the unit to tone dialing.

Make a trial call. If the call connects,

leave the setting as is; otherwise set

the unit to pulse dialing.

• If your phone system requires pulse

dialing and you need to send DTMF

tones in certain situations during a call,

you may switch over to tone dialing

(refer to “Tone Dialing Switch over” on

page 28).

1. Press the MENU soft key. Select the

Global Setup menu, and then the Dial

Mode submenu.

2. Press VOL/RING/ or VOL/RING/ to

select Toneor Pulse(the initial

setting is Tone).

3. Press the OK soft key. You will hear a

confirmation tone.

Download from Www.Somanuals.com. All Manuals Search And Download.

Setting Voice Mail Tone

Voice Mail Tone sets the voice mail tone. If

your service does not support SDT

message signal, set your VMWI (Visual

Message Waiting Indicator) not to detect

SDT message signal.

1. Press MENU soft key. Select the Global

Setup menu, and then the Voice Mail

Tone Submenu.

2. Press VOL/RING/ or VOL/RING/ to

set the voice message indication (SDT

message signal) to Onor Off.

3. Press the OK soft key. You will hear a

confirmation tone.

Deregister the Handset

Deregister HS clears the handset’s ID from

the main base unit and the base ID from the

handset. You will usually only deregister the

handset if you are having a problem with

your phone.

1. Press the MENU soft key. Select

Deregister HS menu. Deregister

HS?appears.

2. Press VOL/RING/ or VOL/RING/ to

select Yesand then the OK soft key.

When de-registration is complete you

will hear a confirmation tone, and

Deregistration Complete

appears.

3. After deregistering the handset, place

the handset to the base to register. You

must reregister the handset before you

can use it.

Download from Www.Somanuals.com. All Manuals Search And Download.

MAKING AND

Ô NOTES Ô

RECEIVING CALLS

•

To set Auto talk, see

“Setting the Auto Talk”

on page 19, or to set

Anykey Answer see

“Setting the Anykey

Answer” on page 19.

From the Handset

This handset has a built-in speakerphone

that allows you to have a hands-free

conversation. This feature allows you to

communicate easily while performing other

tasks, such as cooking. appears during

hands-free conversations. Ô

The handset microphone

is located at the bottom

of the handset. Position

yourself as near to the

handset as possible and

speak clearly.

You can easily switch a call from normal

conversation to hands-free conversation.

To switch a call, press SPEAKER during the

call.

If the line is in use by

another handset(s),

Line In Useappears

in the display of all

registered handset’s

display that are not in

use.

From the Handset

Normal

conversation

Hands-free

conversation

Handset On the

Cradle

Pick up the

handset (Auto

Talk) or pick up

the handset and

press

answer a talk/FLASH.

Handset Off the Handset Off the

Cradle Cradle

call Ô

Press any number Press SPEAKER.

key, /tone/<, or

#/> (Anykey

Answer), or press

talk/FLASH.

Handset Off the Handset Off the

Cradle

1)Press

talk/FLASH.

SPEAKER.

2)Listen for the

dial tone.

3)Dial the number. 3)Dial the number.

OR OR

Dial the number, Dial the number,

2)Listen for the

dial tone.

To make

a call Ô

and then press

talk/FLASH.

SPEAKER.

Download from Www.Somanuals.com. All Manuals Search And Download.

From the Handset

Normal

conversation

Hands-free

conversation

To hang Press end or return the handset to the

up cradle (Auto Standby).

Toentera When you dial the number in standby

pause mode, press the PAUSE soft key. P

within the appears in the display, which

dialing

represents a pause.

sequence

PLACING A CALL ON HOLD

1. During a call, press INTCM/HOLD. The

call will be put on hold. Ô

Ô NOTES Ô

Placing a Call on Hold

•

While a call is on hold,

CIDCW can not be

received.

2. To talk to the caller, press talk/FLASH or

SPEAKER. The phone will return back

to the call.

•

If you leave a call on

hold for more than ten

seconds, the display

screen will read, Line

On Hold.

REDIALING A CALL

The last three phone numbers dialed can be

quickly redialed from the handset. Redial

numbers stored in the handset are

independent from each other. Ô

Redialing a Call

•

If the number exceeds

32 digits, only the first 32

digits are retained in

redial memory.

1. With the phone in standby mode, press

the REDIAL soft key.

•

If the redial memory is

empty, you will hear a

beep.

2. Press VOL/RING/ or VOL/RING/ to

scroll through the last three dialed

numbers.

3. Press talk/FLASH or SPEAKER on the

handset. The selected number is

dialed.

4. To hang up, press end.

Deleting a Redial Record

1. With the phone in standby mode, press

the REDIAL soft key.

Download from Www.Somanuals.com. All Manuals Search And Download.

2. Press VOL/RING/ or VOL/RING/

repeatedly to display the number to be

deleted.

3. Press the DELETE soft key.

4. Press VOL/RING/ or VOL/RING/ to

choose Yes.

5. Press the OK soft key. The redialed

number is deleted.

Storing a Redial Record

1. With the phone in standby mode, press

the REDIAL soft key.

2. Press VOL/RING/ or VOL/RING/

repeatedly to display the number to be

stored.

3. Press the STORE soft key. Store/

Edit Nameappears.

4. To complete the setting, follow the

steps 3-8 in “Storing Phone Numbers,

Names, Distinctive Rings, and Speed

Dials” on page 31.

ADJUSTING THE HANDSET

RINGER, EARPIECE AND

SPEAKER VOLUME

You can adjust the handset ringer and

earpiece/speaker volume separately.

Press the volume up key or volume down

key (labelled as VOL/RING/ or VOL/RING/

) in standby mode to select one of three

ringer volume (off, low, or high). Ô

Ô NOTE Ô

When you press volume up

key (VOL/RING/ ) in the

maximum volume level or

volume down key (VOL/

RING/ ) in the lowest

volume level, an error tone

sounds.

Pressing the volume up key or volume down

key (labelled as VOL/RING/ or VOL/RING/

key) during a call will change the earpiece

volume of the handset. This setting will

remain in effect after the telephone call has

ended.

Download from Www.Somanuals.com. All Manuals Search And Download.

TEMPORARILY MUTING THE

RINGER

You can mute the ringer individually on a

handset. When the phone is ringing,

pressing the MUTE soft key on the handset

you want to mute. This mute will last for the

current incoming call only. The ringer tone

will return to the previous setting on the next

incoming call. Ô

Ô NOTE Ô

While charging a handset,

you can not mute the ringer

tone for the handset.

MUTE MICROPHONE

You can temporarily mute the microphone

so that the caller cannot hear you. Press the

MUTE soft key during talk mode to mute the

microphone.

Mute Onand appear in the display. To

cancel muting, press the MUTE soft key

again. Mute Offappears.

TONE DIALING SWITCH OVER

Some telephone companies use equipment

that requires pulse dialing (sometimes

referred to as rotary dialing). If you need to

enter tone dialing digits, you can switch-

Ô NOTES Ô

The tone feature only

applies when the dial

mode is set to pulse.

This special number can over to tone dialing during the call. This

be stored in a memory

•

feature is useful when you need tone dialing

to use automated systems, for example,

entering your bank account number after

you have called your bank. Ô

location.

This is referred to as

Chain Dialing (see

“Chain Dialing” on

page 37).

Initially make your call with the pulse dialing

mode. Once your call connects, press

/tone/<. Enter the desired number. These

digits will be sent as tone dialing. Once the

call ends, the tone mode is cancelled and

pulse dialing mode resumes.

TRAVELLING OUT-OF-RANGE

During a call, as you begin to move your

handset too far from your base unit, noise

may increase. If you pass the range limits of

the base unit, you will hear a beep and see

Out of Rangeon the display, and then

the handset returns to standby mode.

Download from Www.Somanuals.com. All Manuals Search And Download.

PRIVACY MODE

Privacy mode prevents interruption from

other registered handsets. This works only

when the phone is in use.

Press the PRIVACY soft key on the handset

during talk mode.

Privacy Mode Onand appear in the

display. To exit Privacy Mode, press the

PRIVACY soft key again. Privacy Mode

Offappears.

THREE-WAY CONFERENCING

The phone permits three-way conversations

between two handsets and an outside line.

1. Initiate the call normally. Once the call

is in progress, other people can join the

call.

2. To join a conference call, press

talk/FLASH or SPEAKER to use the

handset speakerphone.

3. To leave a conference call, simply hang

up as you normally would. All other

parties will remain connected.

4. To end a conference call completely, all

local parties must hang up. The

conference call will also end when the

calling party hang up.

FLASH AND CALL WAITING

If you have Call Waiting service and a call

waiting tone sounds while you are on a call,

press talk/FLASH to accept the waiting call.

There is a short pause, and then you will

hear the new caller. To return to the original

caller, press talk/FLASH again. Ô

Ô NOTE Ô

You must subscribe through

your local telephone

company to receive Call

Waiting or Caller ID on call

waiting service.

Download from Www.Somanuals.com. All Manuals Search And Download.

USING ONE TOUCH VOICE

Ô NOTEÔ

MAIL ACCESS

You must subscribe to

voice mail service from your

telephone company in order

to use this feature. The

voice mail service company

will provide you with the

access number.

If you subscribe to voice mail service, you

can use your phone to access your voice

mailbox. The new message LED flashes

whenever you have messages waiting in

your voice mailbox.

Just program the handset with your access

number, and you can get your messages at

the touch of a key on the handset.

The voice mail service provider will supply

you with the access number. This number

may be simply a phone number. Refer to

the provider’s literature.

To program or delete your Voice Mail

Access Number, See page 17.

Dialing your Voice Mail Service

Once you’ve programmed your personal

access number, you can dial your mailbox

with the touch of a key. When you have

messages, simply press the

soft key.

If you have not entered the access number

or it has been deleted, when you press the

soft key, No Number Stored To

store number press [MENU]appears

and you will hear a beep. The phone returns

to standby mode.

Resetting the New Message LED

The LED flashes when you have new

messages in the voice mail service. If the

LED remains on after you’ve retrieved your

messages, you may need to reset the

indicators. With the phone is in standby

mode, press and hold PAGE on the base

until the paging sound stops (about 5

seconds).

Download from Www.Somanuals.com. All Manuals Search And Download.

PHONEBOOK

The Phonebook allows you to dial a number

using just a few key presses. Your phone

stores names/numbers in the phonebook

memory location, and you can search

names in alphabetical order. You have a

total of 100 locations that can be used for

the phonebook (including the speed dials)

and Caller ID messages.

STORING PHONE NUMBERS,

NAMES, DISTINCTIVE RINGS,

AND SPEED DIALS

1. When the phone is in standby mode,

press

The handset displays the following

items:

(1st line) The number of the phonebook

locations used

(2nd line) How to search (press the

number keypad, VOL/RING/ or

VOL/RING/

)

(3rd line) How to enter the storing

operation (press the STORE soft key)

(4th line) The BACK, COPY, and STORE

soft keys

2. Press the STORE soft key, Store/

Ô NOTE Ô

Edit Nameappears. Ô

When the memory is full,

you will hear a beep and

Memory Fullappears.

You cannot store additional

names and numbers when

the memory is full.

3. Enter the name (up to 16 characters)

by using the number keypad (see

“Steps for Entering Names and Special

Characters” on page 32).

If a name is not required, go to step 4.

<No Name> will be used as the name.

4. Press the OK soft key to store the

name, Store/Edit No.appears.

Download from Www.Somanuals.com. All Manuals Search And Download.

5. Press the number keypad to enter the

phone number (up to 20 digits), press

the OK soft key to store the number. Ô

Ô NOTES Ô

Storing Phone Numbers,

Names, Distinctive Rings,

and Speed Dial

6. Distinctive Ringappears. Press

VOL/RING/ or VOL/RING/ to move

the pointer to one of the Distinctive

Ring options, and then press the OK

soft key. Ô

•

The pause key counts as

one digit. Pressing the

PAUSE soft key, more

than once increases the

length of the pause

between numbers. Each

pause represents a two

second delay.

7. Speed Dialappears. Press

VOL/RING/ or VOL/RING/ to move

the pointer to select the Speed dial

location (ten locations: SPD1-SPD0).

•

If you choose not to

store a “Distinctive

Ring”, simply select the

“No Selectn” option.

8. Press the OK soft key. You will hear a

confirmation tone, and Done!appears

in the display.

Selecting a speed dial

location where a number

is already stored,

releases the old

number’s speed dial

setting. The new number

will be stored in the

speed dial location.

STEPS FOR ENTERING NAMES

AND SPECIAL CHARACTERS

Refer to the letters on the number keys to

select the desired characters. With each

press of a number key (0-9), the displayed

character appears in the following order:

•

If you choose not to

store the name/number

as a Speed Dial, simply

select the “No Selectn”

option.

upper case letters first, lower case letters

next and finally the number corresponding

to the key.Ô

Steps for Entering Names

and Special Characters

Number of times key is pressed

•

If the next character

uses the same number

key, you must press #/>

to move the cursor over.

Otherwise the next time

you press the number

key, it changes the

character that was

previously set.

Download from Www.Somanuals.com. All Manuals Search And Download.

If you make a mistake while entering a

name, use /tone/< or #/> to move the cursor

to the incorrect character.

Press the DELETE soft key to erase the

wrong character, and then enter the correct

character.

To delete all characters, press and hold the

DELETE soft key.

For example, to enter Movies:

1. When the phone is in standby mode,

press

2. Press the STORE soft key, Store/

Edit Nameappears.

3. Press 6 once, and then press #/> to

move the cursor to the right.

4. Press 6 six times.

5. Press 8 six times.

6. Press 4 six times.

7. Press 3 five times.

8. Press 7 eight times.

9. When finished, press the OK soft key.

To continue to store the telephone number,

proceed to step 5 on page 32.

VIEWING THE PHONEBOOK

Your phone stores names/numbers in the

phonebook memory locations, and you can

search names in alphabetical order. You

can view the phonebook even while the

phone is in use.

1. Press

Download from Www.Somanuals.com. All Manuals Search And Download.

2. Press VOL/RING/ or VOL/RING/ , or

the number keypad to scroll through the

phonebook locations. Phonebook

locations appear in alphabetical order

(from first to last when you press

VOL/RING/ , from last to first when you

press VOL/RING/ ).

You can also use letters on the number

keys to select the first letter of the

desired name. Press a number key (2-9

and 0) once for the first letter, press

twice for the second letter, and so on.

The first location that begins with the

letter you entered appears.

For example, to search for “Movies”,

press 6 once. Press VOL/RING/ or

VOL/RING/ , until the phonebook

location is displayed.

3. To finish the viewing operation, press

end or the BACK soft key (or talk/FLASH

during a call). Ô

Ô NOTE Ô

During a call, don’t press

end or the call will be

disconnected.

MAKING CALLS USING THE

PHONEBOOK

From Standby Mode

1. When the phone is in standby mode,

view the phonebook location to dial

(see “Viewing the Phonebook” on

page 33).

2. Press talk/FLASH or SPEAKER. The

displayed number is dialed.

3. To hang up press end.

Download from Www.Somanuals.com. All Manuals Search And Download.

From Talk Mode

1. Press talk/FLASH or SPEAKER.

2. View the phonebook location to dial

(see “Viewing the Phonebook” on

page 33).

3. Press the DIAL soft key. The number in

the displayed phonebook location is

dialed.

4. To hang up press end.

SPEED DIALING

If you store a phone number in a speed dial

memory location (ten locations: SPD1 -

SPD0), you can use the speed dialing

feature. When the phone is in standby

mode, press and hold a number key (0-9)

associated with the speed dial until the

phone number appears and then press talk/

FLASH or SPEAKER. The number stored in

the speed dial (SPD1 - SPD0) is dialed.

EDITING OR ERASING A DATA

1. When the phone is in standby mode,

press

2. Press VOL/RING/ or VOL/RING/ , or

the number keypad to view the

phonebook locations (see “Viewing the

Phonebook” on page 33).

Editing the Stored Data

1. When the phonebook location to be

edited appears, press the EDIT soft key.

Store/Edit Nameappears.

2. Follow the steps 3 to 7 under “Storing

Phone Numbers, Names, Distinctive

Rings, and Speed Dials” on page 31-32

to complete the editing operation.

Download from Www.Somanuals.com. All Manuals Search And Download.

3. Press the OK soft key. You will hear a

confirmation tone.

Deleting the Stored Data

1. When the phonebook location to be

deleted appears, press the DELETE soft

key. Delete Memory?appears.

2. Press VOL/RING/ or VOL/RING/ to

move the pointer to Yes.

3. Press the OK soft key. You will hear a

confirmation tone. Deleted!appears

in the display.

COPYING PHONEBOOK

LOCATIONS

Copy Phonebook allows you to transfer

stored phonebook locations from handset to

handset without having to manually re-enter

names and numbers. You can transfer one

memory (phonebook location) at a time, or

all memory locations at once. Ô

Ô NOTE Ô

If the memory location on

the receiving

handset is full, and can not

store the phonebook

locations, you will hear a

beep.

1. When the phone is in standby mode,

press

2. Press the COPY soft key.

3. Press VOL/RING/ or VOL/RING/ , to

select the handset to which you want to

transfer the phonebook locations and

then press the OK soft key.

4. Press VOL/RING/ or VOL/RING/ to

select One Memoryor All

Memories:and then press the OK soft

key.

If you select All Memories, Are you

sure?appears on the display screen.

Press VOL/RING/ or VOL/RING/ to

select Yes, and then press the OK soft

key.

Download from Www.Somanuals.com. All Manuals Search And Download.

If you select One Memory, press VOL/

RING/ or VOL/RING/ , or the number

key (2-9 and 0) to select the phonebook

location you want to export and then

press the COPY soft key.

5. The phonebook locations will be

transferred to the handset. Copying

and the receiving handset name

appear. When the transfer is completed

Done!appears on the handset.

CHAIN DIALING

The memory locations in the handset are

not limited to phone numbers. You can also

store a group of numbers (up to 20 digits),

that you need to enter once your call

connects. This is referred to as Chain

Dialing.

An example of this is a bank account

number. Store the account or special

number in one of the phonebook locations.

(Refer to “Storing Phone Numbers, Names,

Distinctive Rings, and Speed Dials” on

page 31). When you call your bank, and you

are prompted to enter the account number,

scroll through your phonebook locations

until you find your account or special

number, and then press the DIAL soft key.

TESTING STORED EMERGENCY

NUMBERS

If you store an emergency service’s number

(police department, fire department,

ambulance) and you choose to test the

stored number, make the test call during the

late evening or early morning hours to avoid

peak demand periods. Also, remain on the

line to explain the reason for your call.

Download from Www.Somanuals.com. All Manuals Search And Download.

CALLER ID

Ô NOTES Ô

•

If you answer a call

before the Caller ID

message is received (for

example, before the

second ring), the Caller

ID message will not

appear.

CALLER ID AND CIDCW

(CALLER ID ON CALL

WAITING)

You must subscribe to Caller ID services

through your local telephone provider to use

these features.

When the telephone rings, the Caller ID

feature allows you to view the caller’s name,

and phone number along with the date and

time of call. With CIDCW (Caller ID on Call

Waiting), you will hear a call waiting tone

while you are on a call, and the Caller ID

data is displayed. To accept the waiting call,

press talk/FLASH (see “Flash and Call

Waiting” on page 29). Ô

When the call is received

via a telephone company

that does not offer Caller

ID service, the caller’s

phone number and

name does not appear.

(This includes some

international calls.)

•

When the call is via a

private branch exchange

(PBX), the caller's phone

number and name may

not appear.

Additionally, you can dial a number stored in

the Caller ID list or save data to your

Phonebook locations.

When the Caller ID message is received,

the display shows the caller's phone

Data errors appear as

“❚”.

number along with the date and time. The

incoming call information is stored in the

Caller ID record. If the Caller ID service

includes the caller's name, the name will

appear in the display (up to 15 characters).

You may receive any one of the

following messages:

When a private name is received

Private Name

When a private number is received

Private Number

When a unknown name is received

Unknown Name

When a unknown number is received

Unknown Number

When invalid data is received

Incomplete Data

Download from Www.Somanuals.com. All Manuals Search And Download.

When you pick up the phone, the display

changes to Talk. (If Auto Talk feature is set

to on.)

VIEWING THE CALLER ID LIST

The Caller ID list stores information for

incoming calls - even unanswered calls.

You can store 100 Caller ID messages and

Phonebook locations (including Speed

Dials) in total. You can view the Caller ID list

during a call or when the phone is in

standby mode.

IMPORTANT

1. Press CID.

Memory locations for Caller

ID messages and

Phonebook locations

The summary screen appears. The

screen shows the number of new

messages and total messages.

(including Speed Dials) are

shared, you can only store

up to 100 in total. A Caller

ID message is not stored

when you have stored 100

phonebook locations. The

earliest Caller ID message

is overwritten when you

have stored 100 phonebook

locations and Caller ID

messages in total.

To view the Caller ID messages in

historical order (from new to old or from

old to new), repeatedly press VOL/

RING/ to scroll through the messages

from the latest to the earliest, or VOL/

RING/ to scroll back through the

messages.

To view the Caller ID messages with

alphabetical search, press the number

key pad (2-9 and 0) with the letter

associated with the first letter of the

desired message.

2. To finish the viewing operation, press

end (or the BACK soft key or talk/FLASH

during a call).

Download from Www.Somanuals.com. All Manuals Search And Download.

DELETING A CALLER ID

MESSAGE

Deleting Information from the

Caller ID List

1. When the phone is in standby mode,

view the Caller ID information to be

deleted (see “Viewing the Caller ID List”

on page 39). Ô

Ô NOTE Ô

Once the Caller ID data has

been deleted, the

information cannot be

retrieved.

2. Press the DELETE soft key

Delete Caller IDappears.

3. Press VOL/RING/ or VOL/RING/ to

choose Yes.

4. Press the OK soft key. You will hear a

confirmation tone.

Deleting all Caller ID names/

numbers

1. When the phone is in standby mode,

press CID.

2. Press the DELETE soft key. Delete

All?appears.

3. Press VOL/RING/ or VOL/RING/ to

choose Yes.

4. Press the OK soft key. You will hear a

confirmation tone.

USING THE CALLER ID

MESSAGE LIST

Calling a party from the Caller ID

list

From Standby mode

1. When the phone is in standby mode,

view the Caller ID message (see

“Viewing the Caller ID List” on

page 39).

Download from Www.Somanuals.com. All Manuals Search And Download.

2. Press talk/FLASH or SPEAKER. The

displayed phone number dials

automatically.

From Talk mode

1. Press talk/FLASH or SPEAKER.

2. View the Caller ID message you want

to dial (see “Viewing the Caller ID List”

on page 39).

3. Press the DIAL soft key. The displayed

phone number will be dialed.

Long Distance calls and Area Code

Setting/Cancellation

Ô NOTES Ô

When a long distance

call has been set, 1

appears in the display.

While the present Caller ID information is

displayed, pressing /tone/< will place or

•

remove the prefix “1” in the display to set the

call for a long distance call, or pressing #/> will

set or cancel an area code (see “Setting the

Area Code” on page 23). Ô

If a call comes in via a

telephone system that

does not offer Caller ID

service, no information is

stored.

Storing Caller ID messages in the

Phonebook

Messages shown in the Caller ID list can be

stored in the phonebook. The phone

number and name of the party on the Caller

ID list can be stored in memory. Ô

•

If the Caller ID message

was received as a

private/unknown

number, or the message

does not have the

number, you cannot

store the message in the

Phonebook. If it was

received as private/

unknown name, the

message will be stored

as <No Name>.

1. When the phone is in standby mode,

view the Caller ID message to be stored.

Then press the STORE soft key.

Store/Edit Nameappears.

2. To complete the setting, follow the

steps 3-8 in “Storing Phone Numbers,

Names, Distinctive Rings, and Speed

Dials” on page 31-32.

•

Even if the 100 memory

locations are full, the

message will be stored

in the Phonebook.

However, the message

will be erased from the

Caller ID list.

Download from Www.Somanuals.com. All Manuals Search And Download.

CALL WAITING DELUXE

Ô NOTES Ô

FEATURES

•

To activate features,

select CW On/CWDX

Onin the CIDCW option.

See “Setting CIDCW

(Caller ID on Call

Your phone gives you new options for call

waiting. At the touch of a key, you can place

the caller on hold, send them to your voice

mail service, or conference them into your

current call. You may be required to

subscribe to Call Waiting and Call Waiting

Deluxe to use these features. Not all features

are available in all areas. Check with your

local telephone company for details. Ô

Waiting)” on page 22.

You can also answer a

waiting call immediately by

pressing talk/FLASH, the

first caller will be placed on

hold. To return to the

1. When you receive a Call Waiting call,

press the CWDX soft key for a list of

options.

original caller, press talk/

FLASH again.

2. Press VOL/RING/ or VOL/RING/ or

the number keypad (1-7) to select an

option.

•

If you don’t press a key

within 30 seconds while

in the operation, the

phone goes back to the

original call.

3. Press the OK soft key. A confirmation

screen will appear, and returns back to

the call.

Your phone is pre-programmed with seven

call waiting options. You may select to ask

the calling party to hold, send them a busy

message, forward them to your voice mail,

or answer and drop the first caller. You may

also select to conference them into the

current call or, at any time, choose to drop

the first or drop the last caller. Check with

your local telephone company for a full list

of options.

Download from Www.Somanuals.com. All Manuals Search And Download.

EXPANDING YOUR

PHONE

Ten Multi-Handsets Expandability

Your phone supports up to ten handsets

including the handsets supplied with your

phone. You can now place a fully- featured

cordless handset anywhere AC power is

available to connect the handset charger.

With extra handset(s), you can perform

• Three-way conference (two handsets

and an outside line).

• Intercom call between handsets even

while other handsets are on the outside

line.

IMPORTANT

If you purchase a 43-5561

extra handset, please

original/main base before

use. The 43-5561 will not

operate until it is registered.

• Monitoring the room where the other

handset is placed.

• Using as a pair of walkie-talkies, even

outside the base’s communication

range or other handsets are on the

outside line.

All of the handsets ring when a call is

received.

ꢀ

CAUTION

ꢀ

You must use

a Class 2

SETUP THE CHARGER AND

CHARGE THE EXTRA

power source

HANDSET(S)

Insert the supplied

AC adapter's barrel

plug into the DC IN

9V jack on the back

of the charger. ꢀ

Route the cord

that supplies 9V DC and

delivers at least 210 mA.

Its center tip must be set

to positive and its plug

must fit the charger’s DC

IN 9V jack. The supplied

adapter meets these

specifications. Using an

adapter that does not

meet these

through the strain

relief slot and plug

the adapter into a

standard AC outlet.

specifications could

damage the handset or

the adapter.

Download from Www.Somanuals.com. All Manuals Search And Download.

Ô NOTES Ô

All of the handsets ring

when a call is received.

THE BASE

•

If you purchase an extra handset, you need

to register the handset to the base before

use. Only one handset can be registered at

a time. Ô

An extra handset can be

registered when the

main base is in standby

mode.

Handsets supplied with the phone are

registered to the base by the factory.

Handsets that have not been registered

display Place handset on main base

to register. When you register an extra

handset to the base, follow the steps below.

1. Before registering the extra handset,

the battery pack MUST be charged for

15-20 hours.

2. Place the extra handset in the main

base unit to begin registration.

3. While the handset is registering,

Handset Registeringwill appear

in the LCD.

When Registration Completeis

displayed, the handset has been

registered to the base. If

Registration Failedappears,

remove the handset from the base and

try again.

USING THE DIRECTLINK

Ô NOTE Ô

Handsets can be in Direct

Link mode while other

handsets are in use.

MODE

To use this feature, you must enter the two

handsets into the DirectLink mode first. Ô

DirectLink call

1. Press the MENU soft key and select the

DirectLink Mode menu. To enter

DirectLink mode press

[ENTER]appears.

Download from Www.Somanuals.com. All Manuals Search And Download.

2. Press the ENTER soft key to enter

DirectLink mode. You will hear a

confirmation tone, and DirectLink

Mode Completeappears.

3. Press the DirectLink soft key.

4. Select the handset to which you wish to

DirectLink with by pressing the number

keys (1-9, 0). Your handset will then

page the other handset.

5. On the receiving handset, press

talk/FLASH, the ANSWER soft key or if

Anykey Answer is on, press any

number key, /tone/< or #/>.

6. When you finish your conversation,

press end or the END soft key on either

handset. Return the handset to the

cradle, or press the CANCEL soft key

and then the OK soft key to return to

normal standby mode. (cancelling

DirectLink mode).

Ô NOTES Ô

If the party is busy or out

of range, the handset

INTERCOM/CALL TRANSFER

•

FEATURE

You can use handsets as an intercom. Also,

you can place an outside call on hold and

transfer the call to another handset. Ô

returns to standby mode.

If any of the following

occurs while selecting

the other handset, the

operation will be

Intercom

1. Press INTCM/HOLD in standby mode.

cancelled.

2. Select the handset you want to talk with

from the selection list within 30

- talk/FLASH or

SPEAKER is pressed.

seconds. To select the handset, press

VOL/RING/ or VOL/RING/ , and then

press the OK soft key. If you select All,

all handsets will be paged. An intercom

tone sounds.

- An outside call,

intercom or page is

received.

•

When the party does not

answer within one

minute, the operation is

cancelled.

Download from Www.Somanuals.com. All Manuals Search And Download.

To Cancel intercom press the CANCEL

soft key on the initiating handset.

3. On the receiving handset, to answer

the call, press talk/FLASH, INTCM/

HOLD, or the ANSWER soft key. Or

press any number key, /tone/< or #/>

(when Anykey Answer is on), or pick up

the handset from the cradle (when Auto

Talk is on).

4. To hang up the intercom call, press end

or the END soft key on either handset.

Call Transfer Feature

1. During a call, press INTCM/HOLD on the

handset.

Ô NOTE Ô

If the party does not answer

within one minute, the

operation is cancelled.

2. Select a handset to transfer the call within

ten seconds. To select the handset, press

VOL/RING/ or VOL/RING/ , and then

press the OK soft key. If you select All, all

other handsets will be paged.

The call will automatically be placed on

hold, and an intercom tone sounds.

To cancel the transfer, press the CANCEL

soft key, talk/FLASH or SPEAKER on the

initiating handset. Ô

3. On the receiving handset, to answer the

page, press talk/FLASH, the ANSWER

soft key, or INTCM/HOLD. Or press any

number key, /tone/< or #/> (when

Anykey Answer is on), or pick up the

handset from the cradle (When Auto

Talk is on). Ô

4. To hang up the intercom call, press the

END soft key or end on the handset.

5. To speak to the caller, press

talk/FLASH on the receiving handset.

Download from Www.Somanuals.com. All Manuals Search And Download.

FIND HANDSET

Ô NOTE Ô

To locate a misplaced handset, press PAGE

on the base when the phone is in standby

mode. All registered handsets beep for 60

seconds, and Pagingappears on the

handset display. To cancel paging, press

any key on the handset or PAGE on the

base. Ô

If the battery pack is

completely drained, the

handset will not beep when

paging.

Download from Www.Somanuals.com. All Manuals Search And Download.

TROUBLESHOOTING

If your phone is not performing to your expectations, please try these

simple steps first

Symptom

Suggestion

• Make sure the AC adapter is plugged into the

base and wall outlet.

• Make sure the handset is properly seated in the

cradle.

• Make sure the charging contacts on the handset

are clean.

The CHARGE LED won’t

illuminate when the handset

is placed in the cradle.

• Move the handset and/or base to a different

location away from and/or scratchy metal

objects or appliances and try again.

• Make sure that you are not too far from the

base.

The audio sounds weak.

• Check both ends of the base telephone line

cord.

• Make sure the AC adapter is plugged into the

base and wall outlet.

• Disconnect the AC adapter for a few minutes,

and then reconnect it.

• Deregister the handset (see “Deregister the

Handset” on page 24) and register the handset

(see “Register the Handset to the Base” on

page 44).

Can’t make or receive calls.

• Make sure that you are not too far from the

base.

• If an outside call is already established, you

cannot make another outside call.

• Charge the batteries in the handset for 15-20

hours by placing the handset on the base or

charging cradle.

• The handset may be too far away from the base

unit.

• Place the base unit away from appliances or

metal objects.

The handset doesn’t ring or

receive a page.

• Deregister the handset (see “Deregister the

Handset” on page 24) and register the handset

(see “Register the Handset to the Base” on

page 44).

Unavailableappears in • Make sure that another handset is not too far

the display. from the base.

Download from Www.Somanuals.com. All Manuals Search And Download.

Symptom

Suggestion

• Keep the handset away from microwave ovens,

computers, remote control toys, wireless

microphones, alarm systems, intercoms, room

monitors, fluorescent lights, and electrical

appliances.

Severe noise interference.

• Move to another location or turn off the source

of interference.

• The handset was picked up before the second

ring.

• The call was placed through a switchboard.

• Call your local telephone company to verify your

Caller ID service is current.

The Caller ID does not

display.

• Charge the battery pack for 15-20 hours.

• Deregister the handset (see “Deregister the

Handset” on page 24) and register the handset

(see “Register the Handset to the Base” on

page 44).

You cannot register the

handset at the base.

• Deregister the handset (see “Deregister the

Handset” on page 24) and register the handset

(see “Register the Handset to the Base” on

page 44).

• Make sure that you have registered all

handsets.

The handset doesn’t

communicate with

another handsets.

The handset can’t join the

conversation

• Make sure there are not two handsets already

using the three-way conference feature.

If you still have problems, disconnect the phone. If other phones on the

same line work properly, the fault is in this phone or its installation. If you

cannot find the problem, take the phone to your local RadioShack store

for assistance.

Download from Www.Somanuals.com. All Manuals Search And Download.

CARE

Keep the phone dry; if it gets wet, wipe it dry immediately. Use and store

the phone only in normal temperature environments. Handle the phone

carefully; do not drop it. Keep the phone away from dust and dirt, and

wipe it with a damp cloth occasionally to keep it looking new.

SERVICE AND REPAIR

If your phone is not performing as it should, take it to your local

RadioShack store for assistance. To locate your nearest RadioShack,

use the store locator feature on RadioShack’s website

(www.radioshack.com), or call 1-800-The Shack (843-7422) and follow

the menu options. Modifying or tampering with the phone’s internal

components can cause a malfunction and might invalidate its warranty

and void your FCC authorization to operate it.

NOTE ABOUT HANDSET-BASE

REGISTRATION

When you register the handset with the base, unique data is written on

both the base and the handset. The handset registered to one base unit

cannot be used with other base unit unless the registration data is "de-

registered" with the original base unit. This means the handset must be

within the range of the original base unit to de-register. If for any reason

the original base unit is not within the range (or the registration data in

the original base unit is erased), "Out of Range" error takes place and

you cannot de-register the handset.

Should you encounter this trouble, follow these steps to individually de-

1. Remove the handset if it sits on the base.

2. On the handset, press and hold end and # at the same time until you

hear beep.

3. Disconnect the AC adapter.

4. While holding PAGE, connect the AC adapter. Keep pressing PAGE

until the CHARGE LED starts to blink.

5. Wait about five seconds and place the handset on the base and wait

until the CHARGE LED stops flashing.

Download from Www.Somanuals.com. All Manuals Search And Download.

This erases all the handset registration data on the base, not limited to

the handset you placed at Step 5 above. You need to register other

handset(s) also. First de-register the handset as in Step 1 above, and

then place it on the base.

If you have trouble in de-registration, take your base and handset

(including extra handset(s) if you have) to your local RadioShack or call

1-800-The Shack (843-7422) for assistance.

Also, when you request repair or service, please be sure to bring in the

entire system (including extra handset if used) so we can keep your

registration data intact.

Download from Www.Somanuals.com. All Manuals Search And Download.

MAIN MENU FLOW CHART

From standby mode

&KTGEV.KPMꢀ/QFG

4QQOꢀ/QPKVQT

*CPFUGVꢀ5GVWR

&KTGEV.KPMꢀ/QFG

4QQOꢀ/QPKVQT

*CPFUGVꢀ5GVWR

ꢀꢀꢀ570ꢀꢁꢂꢃꢄꢄ#ꢀ

ꢀꢀꢀ*CPFUGVꢀꢅꢁ

ꢀꢀ0GYꢀ%+&ꢃꢀꢀꢆ

$#%-

4'&+#.

/'07

6QꢀGPVGT

&KTGEV.KPMꢀOQFG

RTGUUꢀ='06'4?

6Qꢀ4QQOꢀ/QPKVQT

*CPFUGVꢀꢀꢀꢀꢁꢉ

*CPFUGVꢀꢀꢀꢀꢁꢇ

*CPFUGVꢀꢀꢀꢀꢁꢈ

*CPFUGVꢀꢀꢀꢀꢁꢊ

*CPFUGVꢀꢀꢀꢀꢁꢄ

*CPFUGVꢀꢀꢀꢀꢁꢅ

*CPFUGVꢀꢀꢀꢀꢁꢆ

*CPFUGVꢀꢀꢀꢀꢁꢂ

*CPFUGVꢀꢀꢀꢀꢁꢃ

$#%-

'06'4

ENTER

$#%-

ꢀꢀꢀ570ꢀꢁꢂꢃꢄꢄ#

ꢀꢀꢀ*CPFUGVꢀꢅꢁ

&KTGEV.KPMꢀ/QFG

%#0%'.

&KTGEV.KPM

&KTGEV.KPMꢀ/QFG

4QQOꢀ/QPKVQT

*CPFUGVꢀ5GVWR

4QQOꢀ/QPKVQT

*CPFUGVꢀ5GVWR

)NQDCNꢀ5GVWR

*CPFUGVꢀ5GVWR

)NQDCNꢀ5GVWR

&GTGIKUVGTꢀ*5

$#%-

ꢀꢂ).1$#.ꢀ5'672

&C[ꢀꢁꢀ6KOG

%+&%9

#TGCꢀ%QFG

&KCNꢀ/QFG

ꢀ&GTGIKUVGTꢀ*5!

;GU

$#%-

ꢁ*#0&5'6ꢀ5'672

'FKVꢀ8QKEGꢀ/CKN

4KPIGTꢀ6QPGU

&KUVKPEVKXGꢀ4KPI

#WVQꢀ6CNM

8QKEGꢀ/CKNꢀ6QPG

$#%-

#P[MG[ꢀ#PUYGT

$CPPGT

.CPIWCIG

ꢀ&GTGIKUVTCVKQP

ꢀꢀꢀꢀ%QORNGVG

%QPVTCUV

-G[ꢀ6QWEJꢀ6QPG

#PKOCVKQPꢀ5ETGGP

$#%-

2NCEGꢀJCPFUGV

QPꢀOCKPꢀDCUG

VQꢀTGIKUVGT

4'&+#.

/'07

Download from Www.Somanuals.com. All Manuals Search And Download.

MEMO

Download from Www.Somanuals.com. All Manuals Search And Download.

MEMO

Download from Www.Somanuals.com. All Manuals Search And Download.

MEMO

Download from Www.Somanuals.com. All Manuals Search And Download.

Limited One-Year Warranty

This product is warranted by RadioShack against manufacturing defects in material and

workmanship under normal use for one (1) year from the date of purchase from RadioShack

company-owned stores and authorized RadioShack franchisees and dealers. EXCEPT AS

PROVIDED HEREIN, RadioShack MAKES NO EXPRESS WARRANTIES AND ANY IM-

PLIED WARRANTIES, INCLUDING THOSE OF MERCHANTABILITY AND FITNESS FOR

A PARTICULAR PURPOSE, ARE LIMITED IN DURATION TO THE DURATION OF THE

WRITTEN LIMITED WARRANTIES CONTAINED HEREIN. EXCEPT AS PROVIDED

HEREIN, RadioShack SHALL HAVE NO LIABILITY OR RESPONSIBILITY TO CUSTOMER

OR ANY OTHER PERSON OR ENTITY WITH RESPECT TO ANY LIABILITY, LOSS OR

DAMAGE CAUSED DIRECTLY OR INDIRECTLY BY USE OR PERFORMANCE OF THE

PRODUCT OR ARISING OUT OF ANY BREACH OF THIS WARRANTY, INCLUDING, BUT

NOT LIMITED TO, ANY DAMAGES RESULTING FROM INCONVENIENCE, LOSS OF

TIME, DATA, PROPERTY, REVENUE, OR PROFIT OR ANY INDIRECT, SPECIAL, INCI-

DENTAL, OR CONSEQUENTIAL DAMAGES, EVEN IF RadioShack HAS BEEN ADVISED

OF THE POSSIBILITY OF SUCH DAMAGES.

Some states do not allow limitations on how long an implied warranty lasts or the exclusion

or limitation of incidental or consequential damages, so the above limitations or exclusions

may not apply to you.

In the event of a product defect during the warranty period, take the product and the Ra-

dioShack sales receipt as proof of purchase date to any RadioShack store. RadioShack will,

at its option, unless otherwise provided by law: (a) correct the defect by product repair without

charge for parts and labor; (b) replace the product with one of the same or similar design; or (c)

refund the purchase price. All replaced parts and products, and products on which a refund is

made, become the property of RadioShack. New or reconditioned parts and products may be

used in the performance of warranty service. Repaired or replaced parts and products are war-

ranted for the remainder of the original warranty period. You will be charged for repair or re-

placement of the product made after the expiration of the warranty period.

This warranty does not cover: (a) damage or failure caused by or attributable to acts of God,

abuse, accident, misuse, improper or abnormal usage, failure to follow instructions, improper

installation or maintenance, alteration, lightning or other incidence of excess voltage or current;

(b) any repairs other than those provided by a RadioShack Authorized Service Facility; (c)

consumables such as fuses or batteries; (d) cosmetic damage; (e) transportation, shipping or

insurance costs; or (f) costs of product removal, installation, set-up service adjustment or rein-

stallation.

This warranty gives you specific legal rights, and you may also have other rights which vary

from state to state.

RadioShack Customer Relations, 300 RadioShack Circle, Fort Worth, TX 76102-1964

12/99

43-5560

UPZZ01796BZ

03A06

Printed in China

RadioShack Corporation

Download from Www.Somanuals.com. All Manuals Search And Download.

Fort Worth, Texas 76102

PYLE Audio TV Mount PSW119ST1 User Guide
Rangemaster Film Camera 63000 User Guide
RCA Flat Panel Television HD52W66 User Guide
Renesas Network Card H8S 2378F User Guide
Roland Engraver EGX 20 User Guide
Salem Baking Company Kitchen Grill 252801 User Guide
Samsung DVR 4 CHANNEL DVR User Guide
Sanyo Microwave Oven EM G5595S User Guide
Schumacher Battery Charger SE 4225 User Guide
Scytek electronic Remote Starter G40RS User Guide