2.4 GHz Cordless Telephone
Caller ID/Call Waiting ID
43-3557
Ten-Number Memory Dialing — lets you store up to ten numbers in
memory for easy dialing. (See “Memory Dialing” on page 19.)
Ample Talk and Standby Time —
the supplied battery (when fully
charged) provides about 7 hours of
talk time or 14 days of standby time.
Headset Jack — lets you connect an
optional headset for hands-free
convenience. (See “Headset
Installation” on page 32.)
Auto Talk— lets you
set the phone to
answer a call by simply
lifting the handset from
the base.
IMPORTANT
!
!
If an icon appears at the end of a paragraph, go to the box on that page with the
corresponding icon for pertinent information.
— Warning
— Important ꢀ — Caution Ô — Note
!
o
OWNER’S MANUAL
Please read before using this equipment.
© 2004 RadioShack Corporation.
All Rights Reserved.
RadioShack and RadioShack.com are trademarks
used by RadioShack Corporation.
ENERGYSTAR and the ENERGYSTAR certification mark
are registered US marks.
Download from Www.Somanuals.com. All Manuals Search And Download.
INTRODUCTION
Thank you for purchasing a RadioShack 2.4
GHz Cordless Telephone. Your phone uses
advanced technology to give you superior
audio quality and extended range. The
phone’s Caller ID unit records each caller’s
telephone number (and name, if available in
your area) and the date and time of the call,
as provided by your local phone company to
Caller ID service subscribers. If you
subscribe to Call Waiting with Caller ID, the
phone shows you the incoming caller
information, even when you are already
talking on the phone.
Cordless phones require AC power to
operate. When the power is off, you cannot
make or receive calls by using your phone.
You should also have a phone that does not
need AC power to operate (not a cordless
phone), so you can still make and receive
IMPORTANT
!
!
•
When AC power is lost,
the phone loses the
digital security code
calls if there is an AC power failure.
connection between the
base and the handset.
When power is restored,
put the handset on the
base briefly to restore
this connection so you
can use the handset.
!
•
•
Your phone operates on
standard radio
frequencies as allocated
by the FCC.
It is possible for other
radio units operating
nearby on similar
frequencies to
unintentionally intercept
your conversation or
cause interference. This
possible lack of privacy
can occur with any
cordless phone.
3
Download from Www.Somanuals.com. All Manuals Search And Download.
As an ENERGYSTAR Partner,
RadioShack Corporation has
determined that this product
meets the ENERGYSTAR guidelines
for energy efficiency.
IMPORTANT
INFORMATION
This telephone has been tested and found
to comply with all applicable UL and FCC
standards.
FCC STATEMENT
Your telephone compiles with Part 68 of the
FCC Rules.Upon request, you must provide
the phone’s FCC registration number and
REN to your phone company. These
numbers are on the base unit.
Your phone is not intended to be used with
party-line systems. Connection to party line
service is subject to state tariffs. Contact the
state public utility commission, public
service commission, or corporation
commission for information. Ô
We have designed your phone to conform
to federal regulations, and you can connect
it to most telephone lines. However, each
phone (and each device, such as a
telephone or answering machine) that you
connect to the telephone line draws power
from the telephone line. We refer to this
power draw as the device’s ringer
Ô NOTE Ô
You must not connect your
phone to:
equivalence number, or REN on the back of
your phone.
If you use more than one phone or other
device on the line, add up all of the RENs. If
the total is more than five (three in rural
areas), your telephones might not ring. If
•
•
coin-operated systems
most electronic key
telephone systems
4
Download from Www.Somanuals.com. All Manuals Search And Download.
ringer operation is impaired, remove a
device from the line.
In the unlikely event that your phone causes
problems on the phone line, the phone
company can temporarily discontinue your
service. If this happens, the phone company
attempts to notify you in advance. If
advance notice is not practical, the phone
company notifies you as soon as possible
and advises you of your right to file a
complaint with the FCC.
Also, the phone company can make
changes to its lines, equipment, operations,
or procedures that could affect the operation
of this phone. The telephone company
notifies you of these changes in advance, so
you can take the necessary steps to prevent
interruption of your telephone service.
This device complies with part 15 of the
FCC rules. Operation is subject to the
following two conditions: (1) This device
may not cause harmful interference, and (2)
This device must accept any interference
received, including interference that may
cause undesired operation. Privacy of
communications, may not be ensured when
using this phone.
SURGE PROTECTION
Your telephone has built-in protection
circuits to reduce the risk of damage from
surges in telephone line and power line
current. These protection circuits meet or
exceed the FCC requirements. However,
lightning striking the telephone or power
lines can damage your telephone.
Lightning damage is not common.
Nevertheless, if you live in an area that has
severe electrical storms, we suggest that
you unplug your phone when storms
approach to reduce the possibility of
damage.
5
Download from Www.Somanuals.com. All Manuals Search And Download.
IMPORTANT SAFETY INSTRUCTIONS
When using your telephone equipment, basic safety precautions should
always be followed to reduce the risk of fire, electric shock and injury to
persons, including the following:
1. Do not use this product near water, for example, near a bathtub,
wash bowl, kitchen sink, or laundry tub, in a wet basement or near a
swimming pool.
2. Avoid using a telephone (other than a cordless type) during an
electrical storm. There may be a remote risk of electric shock from
lightning.
3. Do not use the telephone to report a gas leak in the vicinity of the
leak.
4. Use only the power cord and batteries indicated in this manual.
Do not dispose of batteries in a fire. They may explode. Check with
local codes for possible special disposal instructions.
SAVE THESE INSTRUCTIONS
6
Download from Www.Somanuals.com. All Manuals Search And Download.
IMPORTANT CALLER
ID INFORMATION
To use Caller ID and Call Waiting, you must
be in an area where those services are
available and you must subscribe to those
services through your local phone company.
Where Caller ID is offered, one or more
options are generally available:
• caller’s number only
• caller’s name only
• caller’s name and number
If you subscribe to Call Waiting ID and
Caller ID, the system can show you the
incoming caller information, even when you
are already talking on the phone.
7
Download from Www.Somanuals.com. All Manuals Search And Download.
INSTALLATION
Before using your phone, carefully peel the
protective film off the display. The film
protects the handset window during
shipment and is not necessary for use.
SELECTING A LOCATION
You can place the phone’s base on a desk
or table, or mount it on a standard wall plate
or directly on a wall. Select a location that
is:Ô
• near an accessible AC outlet
• near a telephone line jack
• out of the way of normal activities
• away from electrical machinery,
electrical appliances, metal walls or
filing cabinets, wireless intercoms,
alarms, and room monitors
• away from other cordless phones
The base’s location affects the handset’s
range. If you have a choice of several
locations, try each to see which provides the
best performance.
Ô NOTES Ô
If your home has
•
specially wired alarm
equipment connected to
the telephone line, be
sure that installing the
system does not disable
your alarm equipment.
If you have questions
about what will disable
alarm equipment,
Your telephone connects directly to a
modular telephone line jack. If your
telephone wiring does not have a modular
jack, you can update the wiring yourself
using jacks and adapters (available at your
local RadioShack store), or have the
telephone company update the wiring for
you. You must use compatible modular
jacks that are compliant with Part 68 of FCC
Rules. Ô
contact your telephone
company or a qualified
installer.
•
The USOC number of
the jack to be installed is
RJ11C (or RJ11W for a
wall plate jack).
8
Download from Www.Somanuals.com. All Manuals Search And Download.
ON A DESK TOP
1. Plug one end of
the supplied long
modular cord into
the TEL LINE jack
on the back of the
base.
TEL
LINE
DC IN 9V
2. Insert the supplied
AC adapter’s
ꢀ
CAUTION
ꢀ
You must use
barrel plug into the
DC IN 9V jack on
the back of the
base and route the
adapter’s cord
a Class 2
power source
that supplies
!
9V DC and delivers at
least 210 mA. Its center
tip must be set to
through the strain
relief slot on the base.ꢀ
positive and its plug
must fit the phone’s DC
IN 9V jack. The supplied
adapter meets these
specifications. Using an
adapter that does not
meet these
specifications could
damage the phone or
the adapter.
3. Plug the other end of the modular cord
into a modular phone line jack.
4. Plug the adapter into a standard AC
outlet.
ON A WALL PLATE OR WALL
To mount the phone directly on a wall, you
need two screws (not supplied) with heads
that fit into the keyhole slots on the base.
Drill two holes 315/16 inches apart. Thread a
screw into each hole, letting the heads
extend about 1/8 inch.
1. Insert the two of
upper tabs of the
supplied bracket
into the base’s
upper tab slots.
Then slide down
the bracket so that
two of the lower tabs would be inserted
into the lower slots.
9
Download from Www.Somanuals.com. All Manuals Search And Download.
2. Plug one end of the supplied modular
cord (short for a wall plate, long for
direct wall mounting) into the TEL LINE
jack on the base’s back.
3. Plug the supplied AC adapter's barrel
plug into the DC IN 9V jack.
4. Route the adapter
and modular cords
through the
bracket’s grooves.
5. For a wall plate,
align the bracket’s
keyhole slots with
the wall plate
IMPORTANT
The EPA
!
!
studs and slide the base downward to
secure it.
certified
RBRC® Battery
Recycling Seal
on the nickel-
For direct wall
mounting, align
the bracket’s
keyhole slots
with the
mounting
screws and slide
the base
cadmium (Ni-Cd) battery
indicates RadioShack is
voluntarily participating in
an industry program to
collect and recycle these
batteries at the end of their
useful life, when taken out
of service in the United
States or Canada. The
RBRC program provides a
convenient alternative to
placing used Ni-Cd
batteries into the trash or
the municipal waste
stream, which may be
illegal in your area. Please
call 1-800-THE-SHACK (1-
800-843-7422) for
downward to secure it.
6. Plug the adapter into a standard AC
outlet. And plug the modular cord’s
other end into a modular phone line
jack.
CONNECTING/CHARGING THE
information on Ni-Cd
battery recycling and
BATTERY PACK
The phone comes with a rechargeable
nickel-cadmium battery pack in the handset,
but not connected. Before using your
phone, you must connect the battery pack.
disposal bans/restrictions
in your area. RadioShack’s
involvement in this program
is part of the company’s
commitment to preserving
our environment and
Then charge it for about 15–20 hours.
!
conserving our natural
resources.
10
Download from Www.Somanuals.com. All Manuals Search And Download.
1. Press down and slide off the battery
compartment cover.
IMPORTANT
!
!
Be sure the battery pack is
properly connected before
you try to charge it. The
CHARGE/IN USE indicator
lights when the handset is
on the base, even if the
battery pack is not
2. Lift the battery pack out of the
compartment.
3. Plug the battery pack’s connector into
the socket in the compartment (the
connector fits only one way). Then
place the battery pack in the
compartment.
connected.
4. Replace the cover.
To charge the battery pack, place the
handset on the base. The CHARGE/IN USE
indicator on the base lights.
!
Recharge the battery pack when Low
Batteryflashes on the display.Ô
Ô NOTES Ô
•
•
If the phone does not
work, recharge the
battery pack. (The
battery power might be
too low for the display to
operate.)
When you first use the phone after charging
or recharging the battery pack, the phone
might not work and you might hear error
beeps. If this happens, place the handset to
the base to change the digital security code.
If the battery pack
becomes weak during a
call, the handset beeps
and Low Battery
flashes. When this
happens, you cannot
make a call on the
Using a damp cloth, clean the charging
contacts on the handset about once a
month.
phone until you recharge
the battery pack.
About once a month, fully discharge the
battery pack by keeping the handset off the
base until LowBatteryflashes.
Otherwise, the battery pack loses its ability
to fully recharge.
•
If the battery pack is or
the base loses power
while the handset is
away from it, place the
handset on the base to
change the digital
security code. If it was
the handset that lost
power, recharge the
battery pack.
11
Download from Www.Somanuals.com. All Manuals Search And Download.
The supplied battery pack should last about
a year. If the battery pack does not hold a
charge for more than two hours after an
overnight charge, replace it with a new
3.6V, 600 mAh battery pack with a
connector that fits the socket in the battery
compartment. You can order a replacement
battery pack through your local RadioShack
store (or online at RadioShack.com). Install
the new battery pack and charge it for about
24 hours.
WARNING
o
o
Dispose of the old battery
pack promptly and properly.
Do not burn or bury it.
There is a risk of explosion
if battery is replaced by an
incorrect type. Dispose of
used batteries according to
the instructions.
If you have trouble replacing the battery
pack, take the phone to your local
RadioShack for assistance.
o
12
Download from Www.Somanuals.com. All Manuals Search And Download.
OPERATION
MAKING AND RECEIVING
CALLS
Action Handset On Base Handset Off Base
Pick up the handset Press TALK/
(Auto Talk: On) Ô FLASH, any
Ô NOTE Ô
To
answer
a call
or pick up the
number, /TONE/<
Refer to page 17 “Setting
Menu Options” to turn On
the Auto Talk feature if
desired.
handset and press or #/> keys (Auto
TALK/FLASH(Auto Talk: On).
Talk: Off).
1)Pick up the
handset.
1)Press TALK/
FLASH.
2)Press TALK/
FLASH.
2)Listen for the dial
tone.
3)Listen for the dial 3)Dial the number.
tone. OR
To
make 4)Dial the number. Dial the number.
a call OR
1)Pick up the
Then press TALK/
FLASH.
handset.
2)Dial the number.
Then press
TALK/FLASH.
To
hang
up
Press END or return the handset to the
base (Auto Standby).
1)Pick up the
handset.
1)Press TALK/
FLASH.
2)Press TALK/
FLASH.
2)Listen for the dial
tone.
3)Listen for the dial 3)Press PAUSE/
tone.
4)Press PAUSE/
REDIAL.
OR
1)Pick up the
handset.
REDIAL.
OR
Press PAUSE/
REDIAL. Then
press TALK/
FLASH.
To
redial
2)Press PAUSE/
REDIAL. Then
press TALK/
FLASH.
13
Download from Www.Somanuals.com. All Manuals Search And Download.
ADJUSTING THE HANDSET
RINGER AND EARPIECE
VOLUME
Handset Ringer Tone and Volume
Press the volume up key or volume down
key (labeled as,
VOL or
VOL keys) in
standby mode to select one of five ringer
tones and volume combinations. Ring
Type A High, Ring Type A Low, Ring
Type B High, Ring Type B Low, or
Ringer Off.
Earpiece Volume
Press the volume up key or volume down
key (labeled as,
VOL or
VOL keys)
Ô NOTE Ô
When you press volume up
key ( VOL) in Maximum
mode or volume down key
during a call to change the earpiece volume
of the handset. This setting will remain in
effect after the telephone call has ended. Ô
(
VOL) in Low mode, an
Temporarily Mute Ringer
If the handset is off the base, simply press
the END key to temporarily mute the
incoming ring. The ringer will sound with the
next incoming call.
error tone sounds.
REDIAL
The PAUSE/REDIAL key redials the last
number dialed. The redialed number can be
up to 32 digits long.
14
Download from Www.Somanuals.com. All Manuals Search And Download.
TONE DIALING SWITCH-OVER
Some telephone companies use equipment
that requires pulse dialing (sometimes
referred to as rotary dialing).
If you need to enter tone dialing digits, you
can switch-over to tone dialing during the
call. For example, entering your bank
account number after you have called your
bank. Ô
Ô NOTES Ô
The tone feature only
applies when the dial
mode is set to pulse.
•
•
Initially make your call with the pulse dialing
mode.Once your call connects, press the
TONE/< key. Enter the desired number.
These digits will be sent as tone dialing.
Once the call ends, the tone mode is
This special number can
be stored in a memory
location. This is referred
to as Chain Dialing (See
page 23.)
/
canceled and pulse dialing mode resumes.
TRAVELING OUT-OF-RANGE
During a call, as you begin to move your
handset too far from your base unit, noise
increases. If you pass the range limits of the
base unit, your call will terminate within one
minute.
SELECTING A DIFFERENT
CHANNEL
If you encounter interference while using
your phone, you can manually change the
phone´s channel for clear operation. This
function works only when the phone is in
use. Press CH/DELETE. ¨Scanning¨
appears on the display, indicating the phone
is changing to another channel.
15
Download from Www.Somanuals.com. All Manuals Search And Download.
PAGE
Ô NOTES Ô
To locate the handset (while it’s off the
base), press PAGE on the base. The
handset beeps for 60 seconds. Paging is
canceled when pressing any handset key or
the handset is returned to the base. Ô
Page
You can cancel paging by
pressing the PAGE key on
the base.
Flash and Call Waiting
You must subscribe through
your local telephone
company to receive Call
Waiting Service.
FLASH AND CALL WAITING
If you have “Call Waiting” service and a call
waiting tone sounds while you are on a call,
press TALK/FLASH to accept the waiting
call. There is a short pause. Then you will
hear the new caller. To return to the original
caller, press TALK/FLASH again.Ô
Voice Mail Waiting
Indicator
You must subscribe to
voice mail service from your
telephone company in order
to use this feature. The
voice mail company will
provide you with the access
number.
VOICE MAIL WAITING
INDICATOR
If you subscribe to voice mail service, you
can use your cordless telephone to access
your voice mailbox. The CHARGE/IN USE
light on the base of your phone flashes
whenever you have messages waiting in
your voice mailbox. Just program the
SPEED DIAL key with your access number
and you can get your messages at the
touch of a button. (The voice mail service
provider will supply you with the access
number. This number may be simply a
phone number. Refer to the provider’s
literature.)Ô
You may need to occasionally reset the
indicator if it remains On after you have
retrieved your messages. To reset the
indicator, press and hold PAGE for five
seconds.
16
Download from Www.Somanuals.com. All Manuals Search And Download.
SETTING MENU OPTIONS
There are five setup options available. They
are Auto Talk, CIDCW (Caller ID on Call
Waiting), Area Code, Dial Mode and
Language.
Auto Talk allows you to answer the phone
without pressing the TALK/FLASH button.
If the phone rings when Auto Talk is On,
simply remove the handset from the base
and the phone automatically answers the
call. If the phone rings when Auto Talk is
Off, you must press TALK/FLASH to answer
the call. Ô
Ô NOTE Ô
The Cordless phone
features include Auto Talk
and Auto Standby. Auto
Talk allows you to answer a
call by just removing the
handset from the base so
you don’t have to waste
time pushing buttons. Auto
Standby allows you to hang
up by simply returning the
handset to the base.
Changing the Auto Talk and
CIDCW
1. Press and hold CID.
2. Use
VOL or
VOL keys to move the
pointer to the selection that you would
like to change. Press SELECT to toggle
between ¨On¨ and ¨Off¨ for Auto Talk
and CIDCW.
Ô NOTES Ô
Area Code
3. Press END and return the handset to
the base unit to complete the setting.
The handset returns to the standby
mode.
When the area code has
already been stored in
memory, the stored area
code will be displayed. To
change it, use the CH/
DELETE and number keys
to enter the new area code.
Then press SELECT. A
confirmation tone sounds.
To complete the setting,
press END or return the
handset to the base unit.
Entering Your Area Code
If you enter a three-digit area code number
in the Area Code option, your local area
code does not appear in Caller ID
messages. Do not program this option if
your calling area requires ten-digit dialing.
When reviewing Caller ID messages, you
will see only the local seven digit number.
For calls received from outside your local
area code, you will see a full ten-digit
number.
Choosing the Dialing
Mode
Make sure your battery
pack is fully charged
before choosing the dialing
mode.
17
Download from Www.Somanuals.com. All Manuals Search And Download.
1. When the phone is in the standby
mode, press and hold CID. The Caller
ID setting screen appears.
2. Press VOL key twice to select ¨Area
Code¨.
3. Press SELECT.
4. Use the number keys (0 - 9), or CH/
DELETE to enter the three-digit area
code.
5. Press SELECT. A confirmation tone
sounds and the displayed area code is
entered.
6. Press END or return the handset to the
base unit to complete the setting. The
handset returns to the standby mode.Ô
Choosing the Dialing Mode
Most phone systems use tone dialing which
sends DTMF tones through the phone lines.
However some phone systems still use
pulse dialing such as in rural areas. Ô
The default setting is tone dialing.
Depending on your dialing system, set the
mode as follows:
1. When the phone is in the standby
mode, press and hold CID.
2. Press
¨Dial¨.
VOL key three times to select
3. Press SELECT to toggle between
¨Tone¨ and ¨Pulse¨ for each setting.
4. Press END or return the handset to the
base unit to complete the setting. The
handset returns to the standby mode.
18
Download from Www.Somanuals.com. All Manuals Search And Download.
• If you are not sure of your dialing
system, set for tone dialing. Make a
trial call.
If the call connects, leave the setting
as is, otherwise set for pulse dialing.
• If your phone system requires pulse
dialing and you need to send the
DTMF tones for certain situations
during a call, you may “switch-over”
to tone dialing. (Refer to “Tone
Dialing Switch-over” on page 15.)
Setting the Language
1. When the phone is in the standby
mode, press and hold CID.
2. Press
VOL key four times to select
¨Language¨.
3. Press SELECT to toggle between ¨Eng¨,
¨Fr.¨ and ¨Esp¨ for each setting.
4. Press END or return the handset to the
base unit to complete the setting. The
handset returns to the standby mode.
MEMORY DIALING
STORING PHONE NUMBERS
Ô NOTE Ô
In memory dialing
operation, you must press
a key within 30 seconds or
the phone will return to the
standby mode. If you
AND NAMES
Memory Dialing allows you to dial a number
using just a few key presses. Your cordless
telephone stores up to ten names/numbers
in the handset. Ô
return the handset to the
base, the phone will return
to the standby mode also.
1. Press MEM, ¨Select Memory¨ is
displayed.
2. Press
VOL or
VOL keys, or enter a
number (0 - 9) to select the memory
location where you would like to store
the number.
19
Download from Www.Somanuals.com. All Manuals Search And Download.
3. Press MEM or SELECT.
4. Press MEM or SELECT. A cursor flashes
indicating that the display is ready for
the name to be entered.
If “Edit MemoryXX” appears, the
selected memory location is already
stored. Then you must either edit the
entry in this location, delete the entry in
this location, or select ¨Go Back¨ to
choose another location.
5. To enter a name (up to 13 characters),
use the number keys.
• See “Steps for Entering Names and
Special Characters” on page 21.
• Use #/> and /TONE/< keys to move
the cursor to the desired location.
• Use CH/DELETE to delete characters
as needed.
• Press and hold CH/DELETE to delete
all the characters.
• If a name is not required, go to step
6.
6. Press MEM or SELECT. ¨Store
Number¨ is displayed.
The cursor flashes indicating that the
display is ready for the number to be
entered.
7. Use the number keys to enter the
phone number.
• The phone number cannot exceed
20 digits.
20
Download from Www.Somanuals.com. All Manuals Search And Download.
• Use PAUSE/REDIAL to enter a pause
in the dialing sequence. The display
shows a ¨P¨. Each pause counts as
one digit and represents a two
second delay of time between the
digits. Ô
Ô NOTE Ô
The pause feature is useful
for long distance calling,
credit card dialing, or
• Use CH/DELETE to delete digits as
needed.
sequences that require a
pause between digits.
8. Press MEM or SELECT. You will hear a
confirmation tone. Memory storage is
complete. For example, if you store a
name and number into memory
location number 01, the display shows
¨Memory01 Stored¨.
After about two seconds, the Select
Memory screen is displayed.
Repeat steps 2 - 8 to store more
numbers.
9. Press END to return to the standby
mode.
STEPS FOR ENTERING NAMES
AND SPECIAL CHARACTERS
Refer to the letters on the number keys to
select the desired characters.
With each press of a numeric key, the
displayed character appears in the following
order: Upper case letters first, lower case
letters next and finally the number
corresponding to the key. Ô
Ô NOTE Ô
If the next character uses
the same number key, you
must press #/> to move the
cursor over. Otherwise the
next time you press the
number key, it changes the
character that was
previously set.
21
Download from Www.Somanuals.com. All Manuals Search And Download.
For example, to enter Movies.
1. Pick up the handset. Press MEM.
2. Enter a number or press
VOL or
VOL keys to select a memory location.
3. Press MEM or SELECT.
4. Press MEM or SELECT. (When there is
information already stored in the
selected memory location, ¨Edit
MemoryXX¨ is displayed. See page 24
for information on “Editing a Stored
Name and/or Phone Number”.)
5. Press 6. Then press #/>to move the
cursor to the right.
6. Press 6 six times.
7. Press 8 six times.
8. Press 4 six times.
9. Press 3 five times.
10. Press 7 eight times.
11. When finished, press MEM or SELECT.
To continue to store the telephone number,
proceed to step 7 on “Steps for Entering
Names and Special Characters” on
Page 21.
If you make a mistake while
entering a name
Use /TONE/< or #/> keys to move the
cursor to the incorrect character.
Press CH/DELETE to erase the wrong
character. Then enter the correct character.
To delete all characters, press and hold CH/
DELETE.
22
Download from Www.Somanuals.com. All Manuals Search And Download.
MAKING CALLS WITH
MEMORY DIALING
Ô NOTES Ô
Memory Dialing from
Standby Mode
Memory Dialing from Standby
Mode
•
If you press SELECT
before TALK/FLASH,
you can confirm the
name and the number
stored in the selected
memory location.
1. Press MEM. The handset displays your
programmed memory locations.
2. Press
VOL or
VOL keys, or enter
the number (0 - 9) to select the memory
location you would like to dial. Ô
•
•
To exit the memory
function without dialing,
press END. The
handset returns to the
standby mode.
3. Press TALK/FLASH. ¨Talk¨ and the
volume setting appear on the display.
Then the displayed number is dialed. Ô
Whenever you are
using a memory menu
screen, you must press
a key within 30 seconds
or the phone will return
to the standby mode.
Memory Dialing from Talk Mode
1. Press TALK/FLASH. ¨Talk¨ and the
volume setting appears.
2. Press MEM.
Memory dialing from Talk
Mode
If you select a memory
3. Press
VOL or
VOL keys or enter a
number (0 - 9) to select the memory
location of the desired phone number.
The selected name is displayed. Ô
location that does not have
a stored number, the
phone will not dial.
4. The phone number in the memory will
be dialed when the SELECT key is
pressed.
5. To hang up, press END.
CHAIN DIALING
The memory locations on the handset are
not limited to phone numbers. You can also
store a group of numbers (up to 20 digits)
that you need to enter once your call
connects. This is referred to as Chain
Dialing.
23
Download from Www.Somanuals.com. All Manuals Search And Download.
An example of this is a bank account
number. Once you have called your bank,
and are prompted to enter the account
number, press MEM and select the location
number where the special number has been
stored. Then press SELECT.
Store your special number with an
identifying name. (Refer to “Memory
Dialing” on page 19.)
EDITING A STORED NAME
AND/OR PHONE NUMBER
1. Press MEM, ¨Select Memory¨ is
displayed.
2. Press
VOL or
VOL keys, or enter a
number (0 - 9) to select the memory
location you would like to edit, and
press MEM or SELECT.
3. Press MEM or SELECT. The screen
appears with the memory location
number that you have selected in the
display.
4. Press
VOL or
VOL keys to select
¨Edit MemoryXX¨. Then press MEM
or SELECT. Store Nameis displayed.
The cursor flashes indicating that the
display is ready for the name to be
edited. When a name has not been
stored, the cursor appears at the
beginning of the second line.
5. Use the number keys, /TONE/<, #/>
keys, or CH/DELETE to edit the name.
(See “Editing a Stored Name and/or
Phone Number” on Page 24.) To edit
only the phone number, skip this step.
24
Download from Www.Somanuals.com. All Manuals Search And Download.
6. Press MEM or SELECT. The cursor
flashes indicating that the display is
ready for the number to be edited.
7. Use the number key, /TONE/<, #/>,
PAUSE/REDIAL or CH/DELETE to edit
the phone number. The phone number
cannot exceed 20 digits.
If you don’t want to change the phone
number, skip this step.
8. Press MEM or SELECT. If you changed
either name or phone number, a
confirmation display shows up. If it is
correct, press
VOL key to select
“Yes” and press SELECT. You hear a
confirmation tone. The memory storage
is complete.
For example, if you store a name and
number into memory location number
01, the display shows ¨Memory01
Stored¨. After about two seconds,
Select Memory screen is displayed.
9. Press END to return to the standby
mode.
ERASING A STORED NAME
AND PHONE NUMBER
1. Press MEM, ¨Select Memory¨ is
displayed.
2. Press
VOL or
VOL keys, or enter a
number (0 - 9) to select the memory
location you would like to erase.
3. Press MEM or SELECT.
The screen appears with the memory
location number that you have selected
in the display.
25
Download from Www.Somanuals.com. All Manuals Search And Download.
4. Press MEM or SELECT.
5. Press VOL key to move the pointer
down to ¨Delete MemoryXX¨.
6. Press MEM or SELECT. The
confirmation screen appears.
7. Press VOL key to move the pointer to
¨Yes¨.
8. Press SELECT or CH/DELETE.
You hear a confirmation tone.
9. After about two seconds, the display
returns to the Select Memory screen.
You may delete the information in
another memory location (return to step
2) or press END to return to the standby
mode.
TESTING STORED EMERGENCY
NUMBERS
If you store an emergency service’s number
(police department, fire department,
ambulance) and you choose to test the
stored number, make the test call during the
late evening or early morning hours to avoid
peak demand periods. Also, remain on the
line to explain the reason for your call.
ONE-TOUCH SPEED DIAL
You can store your most frequently dialed
number in the SPEED DIAL location. The
One-touch speed dial allows you to dial a
number with one key press. (There is no
need to press TALK/FLASH. The phone will
automatically dial the number stored.)
26
Download from Www.Somanuals.com. All Manuals Search And Download.
STORING AND EDITING THE
Ô NOTES Ô
SPEED DIAL Ô
1. When the phone is in the standby
mode, press and hold SPEED DIAL.
•
•
Number stored in
SPEED DIAL is
independent from the
numbers stored in
Memory Dial.
If “Edit Number” appears, there is a
number already stored. Press
or VOL keys to select ¨Edit
Number¨. Then press SELECT.
VOL
If the SPEED DIAL
does not have a stored
number, the handset
will beep rapidly and the
phone will not dial.
2. Store the number by following step 7
under “Storing Phone Numbers and
Names” on page 19.
3. Press SELECT.
You hear a confirmation tone. Memory
storage is complete.
MAKING CALLS WITH THE
SPEED DIAL
When the phone is in the standby mode,
simply press SPEED DIAL. The number
stored in the SPEED DIAL memory location
is instantly dialed.
DELETING THE SPEED DIAL
1. When the phone is in the standby
mode, press and hold SPEED DIAL.
2. Press
VOL or
VOL keys to select
¨Delete Number¨.
3. Press SELECT.
4. Press VOL key to move the pointer to
¨Yes¨.
5. Press SELECT or CH/DELETE.
You hear a confirmation tone. After
about two seconds, the handset returns
to the standby mode.
27
Download from Www.Somanuals.com. All Manuals Search And Download.
CALLER ID
You must subscribe to Caller ID service
to use this feature.
Ô NOTES Ô
When the telephone rings, the Caller ID
feature allows you to view the caller´s name
and phone number on the display before
you answer the phone. The handset
displays the phone number of the incoming
call, the name, and time. Additionally, you
can dial the displayed number and store the
information for memory dialing. Make sure
you have turned on the Caller ID on Call
Waiting feature. (See “Changing the Auto
Talk and CIDCW” on Page 17.)
•
•
If you answer a call
before the Caller ID
message is received
(Example: before the
second ring), the Caller
ID message will not
appear.
When the call is
received via a
telephone company that
does not offer Caller ID
service, the caller´s
phone number and
name do not appear.
(This includes
WHEN THE TELEPHONE RINGS
1. When the Caller ID message is
received, the display shows the caller´s
phone number along with the date and
time. The incoming call information is
stored in the Caller ID record. If the
Caller ID service includes the caller´s
name, the caller´s name appears on
the display (up to 15 letters).Ô
international calls.)
•
•
When the call is via a
private branch
exchange (PBX), the
caller´s phone number
and name may not
appear.
Data errors appear as
¨
¨.
You may receive any one of the
following messages:
Message
Display
When invalid data is “Incomplete Data”
received
When a private name “Private Name”
is received
When a private
number is received
“Private Number”
“Unknown Name”
“Unknown Number”
When an unknown
name is received
When an unknown
number is received
28
Download from Www.Somanuals.com. All Manuals Search And Download.
2. When you pick up the phone, the
display changes to ¨Talk¨. (Auto Talk
feature is set to on.)
VIEWING THE CALLER ID
Ô NOTES Ô
Viewing the Caller ID
Message List
MESSAGE LIST
The Caller ID list stores information for up to
30 incoming calls - even unanswered calls.
Ô
•
In Caller ID operation, if
no key is pressed for
more than 30 seconds,
an error tone sounds
and the telephone
returns to the standby
mode.
1. Press CID.
The summary screen appears. The
screen shows the number of new
messages and total messages.
•
If a call comes in via a
telephone system that
does not offer Caller ID
service, no information
is stored.
2. Press
VOL key to display the latest
Caller ID message.
3. Press
VOL key to see the next
message. Or press
the previous message.
VOL key to see
•
•
Each message can be
up to 15 characters for
the phone number and
the name.
4. Press END to return to the standby
mode.
The number of calls
from the same Caller ID
appears next to the
received time. Once you
view the new message,
the number will
DELETING INFORMATION
FROM THE CALLER ID LIST
The cordless phone stores up to 30
messages. If the phone receives the 31st
message, the oldest one in the list is
automatically deleted and the newest is
stored. Caller ID data can also be deleted
manually.
disappear.
Deleting a Caller ID
Message
While using the ¨Delete
All?¨ or ¨Delete
Message?¨ screen if no
key is pressed for more
than 30 seconds, an error
tone sounds and the
telephone returns to the
standby mode.
Deleting a Caller ID Message
1. Press CID. Display the message to be
deleted from the Caller ID list by
pressing
VOL or
VOL keys. Ô
2. Press CH/DELETE.
29
Download from Www.Somanuals.com. All Manuals Search And Download.
3. Press
VOL or
VOL keys to select
¨Yes¨ or ¨No¨.
4. Press SELECT or CH/DELETE.
When the pointer is at ¨Yes¨: Ô
A tone sounds and the Caller ID
message is deleted. The next Caller ID
message is then displayed.
Ô NOTES Ô
Deleting a Caller ID
Message
If you get an incoming call
or page, the deleting
operation is canceled and
you can answer the call or
page.
When the pointer is at ¨No¨:
The display returns to the Caller ID
message.
Deleting all Caller ID Names/
Numbers Ô
Deleting all Caller ID
Names/Numbers
You cannot make a call
1. Press CID.
from the Caller ID list if
your cordless telephone is
connected to a private
branch exchange (PBX).
2. Press CH/DELETE.
3. Press
VOL or
VOL keys to select
¨Yes¨ or ¨No¨.
Calling a Party from the
Caller ID List
You can place a call from
4. Press SELECT or CH/DELETE.
talk mode.
Press TALK/FLASH. Then
press CID.
Select the phone number
that you want to dial by
When the pointer is at ¨Yes¨:
A tone sounds and all stored Caller ID
messages are deleted.
When the pointer is at ¨No¨:
The display returns to the summary
screen.
pressing the
VOL or
VOL key. Press SELECT.
The displayed phone
number will be dialed.
USING THE CALLER ID LIST
Calling a Party from the Caller
ID List
You can place a call from the Caller ID list.
The cordless phone stores up to 30
messages.Ô
30
Download from Www.Somanuals.com. All Manuals Search And Download.
1. Press CID. Select the phone number
that you want to dial by pressing VOL
or VOL keys.
2. Press TALK/FLASH. The displayed
phone number dials automatically.
Long Distance Calls and Area
Code Setting/Cancellation
Pressing 1 while the incoming Caller ID
information is displayed will place or remove
the prefix 1in the display to set up for a long
distance call or cancel. Pressing 3 will set or
cancel an area code setting. Ô
Ô NOTES Ô
Long Distance Calls and
Area Code Setting/
Cancellation
When a long distance call
has been set, ¨1¨ appears
Storing Caller ID Messages in
Memory Dialing
in the display.
Storing Caller ID
Messages in Memory
Dialing
Messages shown in the Caller ID list can be
stored in memory dialing. Using the
incoming call information (i.e., Caller ID list),
the phone number of the party on the Caller
ID list can be stored in memory.Ô
•
You cannot store a
Caller ID message if no
phone number appears
in the message.
1. Press CID.
•
If a message has
already been stored in
the selected memory
number location, a
confirmation screen is
displayed.
Select the phone number to be stored
from the Caller ID list by pressing
VOL or
VOL keys.
2. Press MEM.
3. Press
Press
VOL key to
select ¨Yes¨. Press
SELECT to overwrite.
The display returns to
the Caller ID list.
VOL or
VOL keys or enter a
number (0 - 9) to select the memory
location to be stored.
4. Press SELECT. Ô
You hear a confirmation tone, and the
number is stored in memory. The
display returns to the Caller ID list.
31
Download from Www.Somanuals.com. All Manuals Search And Download.
ADDITIONAL
INFORMATION
INSTALLING THE BELTCLIP
To attach the beltclip
Insert the beltclip into the holes on each
side of the handset. Press down until it
clicks.
To remove the beltclip
Pull both sides of the beltclip to release the
tabs from the holes.
HEADSET INSTALLATION
You can connect an optional headset with a
3/32-inch (2.5-mm) plug. Contact
RadioShack for a suitable headset.
To connect the headset, open the rubber
cover on the side of the handset. Then
insert the headset’s plug into the jack.Ô
Ô NOTES Ô
•
•
If you place the handset
on the base to recharge
it while the headset is
connected, be sure the
handset seats properly.
When you finish using the headset,
disconnect it from the handset and close the
rubber cover to protect the jack.
You can use a handset
holder (available from
your local RadioShack
store) to hang the
handset on your belt for
greater convenience
when using a headset.
32
Download from Www.Somanuals.com. All Manuals Search And Download.
TROUBLESHOOTING
If your phone is not performing to your expectations, please try these
simple steps first
Problem
Solution
• Make sure the AC adapter is plugged into the
base and wall outlet.
• Make sure the handset is properly seated on the
base.
• Make sure the charging contacts on the handset
and base are clean.
The CHARGE/IN USE
indicator won’t illuminate
when the handset is placed
on the base.
• Make sure that the base antenna is in a vertical
position.
• Move the handset and/or base to a different
location away from metal objects or appliances
and try again.
• Press CH/DELETE to help eliminate
background noise.
The audio sounds weak
and/or scratchy.
• Make sure that you are not too far from the
base.
• Check both ends of the base telephone line cord.
• Make sure the AC adapter is plugged into the
base and wall outlet.
• Disconnect the AC adapter for a few minutes.
Then reconnect it.
Can’t make or receive calls.
• Make sure that you are not too far from the base.
• The battery pack may be weak. Charge the
battery for 15-20 hours.
The handset doesn’t ring or • The handset may be too far away from the base
receive a page.
unit.
• Place the base unit away from appliances or
metal objects.
• Keep the handset away from microwave ovens,
computers, remote control toys, wireless
microphones, alarm systems, intercoms, room
monitors, fluorescent lights, and electrical
appliances.
Severe noise interference.
• Move to another location or turn off the source
of interference.
33
Download from Www.Somanuals.com. All Manuals Search And Download.
Problem
Solution
• The handset was picked up before the second
ring.
The Caller ID does not
display.
• The call was placed through a switchboard.
• Call your local telephone company to verify your
Caller ID service is current.
• Charge the handset.
• Contact your local telephone company to make
sure that your telephone receives FSK message
signaling.
Voice Message Indication
does not work.
If you still have problems, disconnect the
phone. If other phones on the same line
work properly, the fault is in this phone or its
installation. If you cannot find the problem,
take the phone to your local RadioShack
store for assistance.
CARE
Keep the phone dry; if it gets wet, wipe it dry
immediately. Use and store the phone only
in normal temperature environments.
Handle the phone carefully; do not drop it.
Keep the phone away from dust and dirt,
and wipe it with a damp cloth occasionally to
keep it looking new.
SERVICE AND REPAIR
If your phone is not performing as it should,
take it to your local RadioShack store for
assistance. To locate your nearest
RadioShack, use the store locator feature
on RadioShack’s website
Shack (843-7422) and follow the menu
options. Modifying or tampering with the
phone’s internal components can cause a
malfunction and might invalidate its
warranty and void your FCC authorization to
operate it.
34
Download from Www.Somanuals.com. All Manuals Search And Download.
35
Download from Www.Somanuals.com. All Manuals Search And Download.
Limited One-Year Warranty
This product is warranted by RadioShack against manufacturing defects in material and
workmanship under normal use for one (1) year from the date of purchase from RadioShack
company-owned stores and authorized RadioShack franchisees and dealers. EXCEPT AS
PROVIDED HEREIN, RadioShack MAKES NO EXPRESS WARRANTIES AND ANY IM-
PLIED WARRANTIES, INCLUDING THOSE OF MERCHANTABILITY AND FITNESS FOR A
PARTICULAR PURPOSE, ARE LIMITED IN DURATION TO THE DURATION OF THE
WRITTEN LIMITED WARRANTIES CONTAINED HEREIN. EXCEPT AS PROVIDED
HEREIN, RadioShack SHALL HAVE NO LIABILITY OR RESPONSIBILITY TO CUSTOMER
OR ANY OTHER PERSON OR ENTITY WITH RESPECT TO ANY LIABILITY, LOSS OR
DAMAGE CAUSED DIRECTLY OR INDIRECTLY BY USE OR PERFORMANCE OF THE
PRODUCT OR ARISING OUT OF ANY BREACH OF THIS WARRANTY, INCLUDING, BUT
NOT LIMITED TO, ANY DAMAGES RESULTING FROM INCONVENIENCE, LOSS OF
TIME, DATA, PROPERTY, REVENUE, OR PROFIT OR ANY INDIRECT, SPECIAL, INCI-
DENTAL, OR CONSEQUENTIAL DAMAGES, EVEN IF RadioShack HAS BEEN ADVISED
OF THE POSSIBILITY OF SUCH DAMAGES.
Some states do not allow limitations on how long an implied warranty lasts or the exclusion or
limitation of incidental or consequential damages, so the above limitations or exclusions may
not apply to you.
In the event of a product defect during the warranty period, take the product and the Ra-
dioShack sales receipt as proof of purchase date to any RadioShack store. RadioShack will,
at its option, unless otherwise provided by law: (a) correct the defect by product repair with-
out charge for parts and labor; (b) replace the product with one of the same or similar design;
or (c) refund the purchase price. All replaced parts and products, and products on which a re-
fund is made, become the property of RadioShack. New or reconditioned parts and products
may be used in the performance of warranty service. Repaired or replaced parts and prod-
ucts are warranted for the remainder of the original warranty period. You will be charged for
repair or replacement of the product made after the expiration of the warranty period.
This warranty does not cover: (a) damage or failure caused by or attributable to acts of God,
abuse, accident, misuse, improper or abnormal usage, failure to follow instructions, improper
installation or maintenance, alteration, lightning or other incidence of excess voltage or cur-
rent; (b) any repairs other than those provided by a RadioShack Authorized Service Facility;
(c) consumables such as fuses or batteries; (d) cosmetic damage; (e) transportation, ship-
ping or insurance costs; or (f) costs of product removal, installation, set-up service adjust-
ment or reinstallation.
This warranty gives you specific legal rights, and you may also have other rights which vary
from state to state.
RadioShack Customer Relations, 200 Taylor Street, 6th Floor, Fort Worth, TX 76102
12/99
43-3557
UPZZ01040BZ
01A04
Printed in China
RadioShack Corporation
Fort Worth, Texas 76102
Download from Www.Somanuals.com. All Manuals Search And Download.
|