Radio Shack Amplified Phone 43 3241 User Guide

$KI"$WVVQP"#ORNKHKGF"35//GOQT["2JQPG  
43-3241  
OWNER’S MANUAL — Please read before using this equipment.  
(%%"56#6'/'06  
"+/2146#06"  
#
#
If an icon appears at the end of a paragraph,  
go to the box on that page with the  
corresponding icon for pertinent information.  
Your telephone complies with Part 68 of  
notifies you as soon as possible and advises  
you of your right to file a complaint with the  
FCC.  
FCC Rules. You must, upon request,  
provide the FCC registration number and the  
REN (see below) to your telephone  
company. Both numbers are on the bottom  
of your phone. ±  
— Warning  
— Important  
#
Rý  
± — Note  
Also, the phone company can make  
. — Caution  
° — Hint  
changes to its lines, equipment, operations,  
or procedures that could affect the operation  
of this telephone. The telephone company  
notifies you of these changes in advance, so  
you can take the necessary steps to prevent  
interruption of your telephone service.  
We have designed your telephone to  
conform to federal regulations, and you can  
connect it to most telephone lines. However,  
each telephone (and each device, such as a  
telephone or answering machine) that you  
connect to the telephone line draws power  
from the telephone line. We refer to this  
power draw as the device's ringer  
WARNING: To reduce the risk of fire or shock hazard, do not expose this  
product to rain or moisture.  
CAUTION: TO REDUCE THE  
..CAUTION..  
RISK OF ELECTRIC SHOCK, DO  
NOT REMOVE COVER OR BACK.  
NO USER-SERVICEABLE PARTS  
INSIDE. REFER SERVICING TO  
QUALIFIED PERSONNEL.  
RISK OF ELECTRIC  
!
SHOCK DO NOT OPEN  
The lightning symbol is intended to  
alert you to the presence of uninsulated  
dangerous voltage within this  
The exclamation symbol is  
intended to inform you that  
important operating and  
.+)*60+0)  
!
product’s enclosure that might be of  
maintenance instructions are  
included in the literature accompanying  
this product.  
sufficient magnitude to constitute a risk of electric  
shock. Do not open the product’s case.  
Your telephone has built-in protection  
circuits to reduce the risk of damage from  
surges in telephone line and power line  
current. These protection circuits meet or  
exceed the FCC requirements. However,  
lightning striking the telephone or power  
lines can damage your telephone.  
equivalence number, or REN on the bottom  
of your phone.  
If you use more than one phone or other  
device on the line, add up all of the RENs. If  
the total is more than five (three in rural  
areas), your telephones might not ring. If  
ringer operation is impaired, remove a  
device from the line.  
±"016'"±"  
FCC Statement  
You must not connect your telephone to:  
coin-operated systems  
Lightning damage is not common.  
Nevertheless, if you live in an area that has  
severe electrical storms, we suggest that  
you unplug your phone when storms  
approach to reduce the possibility of  
damage.  
party-line systems  
most electronic key telephone systems  
In the unlikely event that your phone causes  
problems on the phone line, the phone  
company can temporarily discontinue your  
service. If this happens, the phone company  
attempts to notify you in advance. If advance  
notice is not practical, the phone company  
Connecting the Phone  
The USOC number of the jack to be  
installed is RJ11C (or RJ11W for a wall  
plate jack).  
Your phone is ETL listed to UL standards  
and meets applicable FCC requirements.  
You can set the phone on a flat surface or  
mount it directly on a wall or a wall plate  
using the supplied mounting bracket.  
%100'%6+0)"6*'"2*10'  
Your telephone connects directly to a  
modular telephone line jack. If your  
telephone wiring does not have a modular  
jack, you can update the wiring yourself  
using jacks and adapters (available at your  
local RadioShack store), or have the  
telephone company update the wiring for  
you. You must use compatible modular  
jacks that are compliant with Part 68 of FCC  
Rules. ±  
supplied) into each hole, letting the heads  
3
16  
extend about / inch (5 mm) from the wall.  
Connect the supplied long modular cord to  
the phone’s line jack. Fit the keyhole slots  
over the screw heads and slide the phone  
downward to secure it. Plug the line cord  
into the telephone line jack.  
To mount the phone on a wall plate, connect  
the supplied short modular cord as shown.  
Fit the keyhole slots over the wall plate studs  
and slide the phone downward to secure it.  
Position the supplied mounting bracket so  
the mounting hole’s open end is facing  
downward, then insert the supplied  
mounting bracket’s two tabs into the  
matching slots on the bottom of the base,  
then snap the bracket into place.  
To mount the  
phonedirectly  
on a wall, drill  
Before you hang up the handset on a wall-  
mounted phone, slide up the handset holder  
out of its slot, turn it, and slide it back into its  
slot.  
two holes  
15  
16  
3 / inches  
(100 mm)  
apart. Then  
thread a  
Plug the handset cord into the jacks on the  
handset and the base.  
screw (not  
© 2002 RadioShack Corporation.  
All Rights Reserved.  
RadioShack and RadioShack.com are trademarks  
used by RadioShack Corporation.  
Download from Www.Somanuals.com. All Manuals Search And Download.  

Q See Home Security System QT208 818 User Guide
RocketFish Headphones RF CNA2 User Guide
Roland Electronic Keyboard ep 77 User Guide
Samsung Digital Camera DV300BK User Guide
Samsung Flat Panel Television 320MP User Guide
Sanyo Camcorder VPC TH1 User Guide
Sanyo Projector PLC SU33 User Guide
Seagate Computer Drive U Series 9 CE User Guide
Seagate Computer Hardware ST31000524NS User Guide
Sekonic Camera Accessories 57 User Guide