OPERATOR’S MANUAL
7-1/4 in. CIRCULAR SAW
DOUBLE INSULATED
R3202
Your circular saw has been engineered and manufactured to our high standards for dependability, ease of operation, and
operator safety. When properly cared for, it will give you years of rugged, trouble-free performance.
WARNING:
To reduce the risk of injury, the user must read and understand the operator’s manual before using this product.
Thank you for buying a RIDGID® product.
SAVE THIS MANUAL FOR FUTURE REFERENCE
Download from Www.Somanuals.com. All Manuals Search And Download.
GENERAL POWER TOOL SAFETY WARNINGS AND
INSTRUCTIONS
Use personal protective equipment. Always wear eye
WARNING!
Read all safety warnings and instructions.
Failure to follow the warnings and instructions may
result in electric shock, fire and/or serious injury.
protection. Protective equipment such as dust mask,
non-skid safety shoes, hard hat, or hearing protection
used for appropriate conditions will reduce personal
injuries.
Prevent unintentional starting. Ensure the switch is in
the off-position before connecting to power source
and/or battery pack, picking up or carrying tool.
Carrying power tools with your finger on the switch or
energising power tools that have the switch on invites
accidents.
Save all warnings and instructions for future
reference.
The term “power tool” in the warnings refers
to your mains-operated (corded) power tool or
battery-operated (cordless) power tool.
Remove any adjusting key or wrench before turning
the power tool on. A wrench or a key left attached to
a rotating part of the power tool may result in personal
injury.
WORk AREA SAFETY
keep work area clean and well lit. Cluttered or dark
areas invite accidents.
Do not overreach. keep proper footing and balance
at all times. This enables better control of the power tool
in unexpected situations.
Dress properly. Do not wear loose clothing or
jewellery. keep your hair, clothing, and gloves away
from moving parts. Loose clothes, jewellery or long hair
can be caught in moving parts.
If devices are provided for the connection of dust
extraction and collection facilities, ensure these are
connected and properly used. Use of dust collection
can reduce dust-related hazards.
Do not operate power tools in explosive atmo-
spheres, such as in the presence of flammable
liquids, gases, or dust. Power tools create sparks which
may ignite the dust or fumes.
keep children and bystanders away while operating a
power tool. Distractions can cause you to lose control.
ELECTRICAL SAFETY
Power tool plugs must match the outlet. Never modify
the plug in any way. Do not use any adapter plugs with
earthed (grounded) power tools. Unmodified plugs and
matching outlets will reduce risk of electric shock.
POWER TOOL USE AND CARE
Avoid body contact with earthed or grounded surfaces
such as pipes, radiators, ranges and refrigerators.
There is an increased risk of electric shock if your body
is earthed or grounded.
Do not force the power tool. Use the correct power
tool for your application. The correct power tool will
do the job better and safer at the rate for which it was
designed.
Do not expose power tools to rain or wet conditions.
Water entering a power tool will increase the risk of
electric shock.
Do not use the power tool if the switch does not turn
it on and off. Any power tool that cannot be controlled
with the switch is dangerous and must be repaired.
Do not abuse the cord. Never use the cord for carrying,
pulling or unplugging the power tool. keep cord away
from heat, oil, sharp edges, or moving parts. Damaged
or entangled cords increase the risk of electric shock.
Disconnect the plug from the power source and/or
the battery pack from the power tool before making
any adjustments, changing accessories, or storing
power tools. Such preventive safety measures reduce
the risk of starting the power tool accidentally.
Store idle power tools out of the reach of children and
do not allow persons unfamiliar with the power tool
or these instructions to operate the power tool. Power
tools are dangerous in the hands of untrained users.
Maintain power tools. Check for misalignment or
binding of moving parts, breakage of parts, and any
other condition that may affect the power tool’s
operation. If damaged, have the power tool repaired
before use. Many accidents are caused by poorly
maintained power tools.
When operating a power tool outdoors, use an
extension cord suitable for outdoor use. Use of a
cord suitable for outdoor use reduces the risk of electric
shock.
If operating a power tool in a damp location is
unavoidable, use a residual current device (RCD)
protected supply. Use of an RCD reduces the risk of
electric shock.
Note: The term “residual current device (RCD)” may be
replaced by the term “ground fault circuit interrupter
(GFCI)” or “earth leakage circuit breaker (ELCB).”
keep cutting tools sharp and clean. Properly maintained
cutting tools with sharp cutting edges are less likely to
bind and are easier to control.
Use the power tool, accessories and tool bits etc. in
accordancewiththeseinstructions,takingintoaccount
the working conditions and the work to be performed.
Use of the power tool for operations different from those
intended could result in a hazardous situation.
PERSONAL SAFETY
Stay alert, watch what you are doing and use
common sense when operating a power tool. Do
not use a power tool while you are tired or under the
influence of drugs, alcohol or medication. A moment
of inattention while operating power tools may result in
serious personal injury.
3
Download from Www.Somanuals.com. All Manuals Search And Download.
GENERAL POWER TOOL SAFETY WARNINGS AND
INSTRUCTIONS
SERVICE
Have your power tool serviced by a qualified repair
person using only identical replacement parts. This will
ensure that the safety of the power tool is maintained.
CIRCULAR SAW SAFETY WARNINGS AND INSTRUCTIONS
Kickback is the result of saw misuse and/or incorrect
operating procedures or conditions and can be avoided by
taking proper precautions as given below:
DANGER:
keep hands away from cutting area and the
blade. keep your second hand on auxiliary
handle, or motor housing. If both hands are
holding the saw, they cannot be cut by the
blade.
Maintain a firm grip with both hands on the saw and
position your arms to resist kickback forces. Position
your body to either side of the blade, but not in line
with the blade. Kickback could cause the saw to jump
backwards, but kickback forces can be controlled by the
operator, if proper precautions are taken.
When blade is binding, or when interrupting a cut
for any reason, release the trigger and hold the saw
motionless in the material until the blade comes to a
completestop.Neverattempttoremovethesawfrom
the work or pull the saw backward while the blade
is in motion or kickback may occur. Investigate and
take corrective actions to eliminate the cause of blade
binding.
Donotreachunderneaththeworkpiece.Theguardcan
not protect you from the blade below the workpiece.
Adjust the cutting depth to the thickness of the
workpiece.Lessthanafulltoothofthebladeteethshould
be visible below the workpiece.
Never hold piece being cut in your hands or across
your leg. Secure the workpiece to a stable platform.
It is important to support the work properly to minimize
body exposure, blade binding, or loss of control.
Hold power tool by insulated gripping surfaces when
performing an operation where the cutting tool may
contact hidden wiring or its own cord. Contact with
a “live” wire will also make exposed metal parts of the
power tool “live” and shock the operator.
When restarting a saw in the workpiece, centre the
saw blade in the kerf and check that saw teeth are
not engaged into the material. If saw blade is binding,
it may walk up or kickback from the workpiece as the
saw is restarted.
When ripping always use a rip fence or straight edge
guide. This improves the accuracy of cut and reduces
the chance of blade binding.
Always use blades with correct size and shape
(diamond versus round) of arbour holes. Blades that
do not match the mounting hardware of the saw will run
eccentrically, causing loss of control.
Never use damaged or incorrect blade washers or
bolt. Thebladewashersandboltwerespeciallydesigned
for your saw, for optimum performance and safety of
operation.
Support large panels to minimise the risk of blade
pinching and kickback. Large panels tend to sag under
their own weight. Supports must be placed under the
panel on both sides, near the line of cut and near the
edge of the panel.
Do not use dull or damaged blades. Unsharpened
or improperly set blades produce narrow kerf causing
excessive friction, blade binding and kickback.
Bladedepthandbeveladjustinglockingleversmustbe
tightandsecurebeforemakingcut.Ifbladeadjustment
shifts while cutting, it may cause binding and kickback.
Use extra caution when making a “plunge cut” into
existingwallsorotherblindareas.Theprotrudingblade
may cut objects that can cause kickback.
CAUSES AND OPERATOR PREVENTION OF
kICkBACk
Kickback is a sudden reaction to a pinched, bound, or
misaligned saw blade, causing an uncontrolled saw to lift
up and out of the workpiece toward the operator.
Checklowerguardforproperclosingbeforeeachuse.
Donotoperatesawiflowerguarddoesnotmovefreely
andcloseinstantly.Neverclamportiethelowerguard
into the open position. If saw is accidentally dropped,
lower guard may be bent. Raise the lower guard with the
retracting handle and make sure it moves freely and does
not touch the blade or any other part, in all angles and
depths of cut.
Whenthebladeispinchedorboundtightlybythekerfclosing
down, the blade stalls and the motor reaction drives the unit
rapidly back toward the operator.
If the blade becomes twisted or misaligned in the cut, the
teeth at the back edge of the blade can dig into the top
surface of the wood causing the blade to climb out of the
kerf and jump back toward the operator.
4
Download from Www.Somanuals.com. All Manuals Search And Download.
CIRCULAR SAW SAFETY WARNINGS AND INSTRUCTIONS
Check the operation of the lower guard spring. If the
Inspect tool cords periodically and, if damaged, have
guard and the spring are not operating properly, they
repaired at your nearest authorized service center.
must be serviced before use. Lower guard may operate
Constantly stay aware of cord location. Following this
sluggishly due to damaged parts, gummy deposits, or a
rule will reduce the risk of electric shock or fire.
build-up of debris.
Check damaged parts. Before further use of the
Lower guard should be retracted manually only for
tool, a guard or other part that is damaged should
be carefully checked to determine that it will operate
properly and perform its intended function. Check for
alignment of moving parts, binding of moving parts,
breakage of parts, mounting, and any other conditions
that may affect its operation. A guard or other part that
is damaged should be properly repaired or replaced
special cuts, such as “plunge cuts” and “compound
cuts.” Raise lower guard by retracting handle and as
soon as blade enters the material, the lower guard
must be released. For all other sawing, the lower guard
should operate automatically.
Always observe that the lower guard is covering the
blade before placing saw down on bench or floor. An
by an authorized service center. Following this rule will
unprotected, coasting blade will cause the saw to walk
reduce the risk of shock, fire, or serious injury.
backwards, cutting whatever is in its path. Be aware
of the time it takes for the blade to stop after switch is
released.
Make sure your extension cord is in good condition.
When using an extension cord, be sure to use one
heavy enough to carry the current your product will
draw. A wire gauge size (A.W.G.) of at least 12 is
recommended for an extension cord 50 feet or less in
length. Acordexceeding100feetisnotrecommended.
If in doubt, use the next heavier gauge. The smaller
the gauge number, the heavier the cord. An undersized
cord will cause a drop in line voltage resulting in loss of
power and overheating.
ADDITIONAL SAFETY RULES
Hold power tools by insulated gripping surfaces when
performing an operation where the cutting tool may
contact hidden wiring or its own cord. Contact with a
“live” wire will make exposed metal parts of the tool “live”
and shock the operator.
know your power tool. Read operator’s manual
carefully. Learn its applications and limitations, as well
as the specific potential hazards related to this tool.
Following this rule will reduce the risk of electric shock,
fire, or serious injury.
Inspect for and remove all nails from lumber before
using this tool. Following this rule will reduce the risk of
serious personal injury.
Ifthepowersupplycordisdamaged,itmustbereplaced
only by the manufacturer or by an authorized service
center to avoid risk.
Always wear safety glasses. Everyday eyeglasses
have only impact-resistant lenses; they are NOT safety
glasses. Following this rule will reduce the risk of serious
personal injury.
Do not wear loose clothing or jewellery. Contain long
hair. Loose clothes, jewellery, or long hair can be drawn
into air vents.
Do not use on a ladder or unstable support. Stable
footing on a solid surface enables better control of the
tool in unexpected situations.
Protect your lungs. Wear a face or dust mask if the
operation is dusty. Following this rule will reduce the
risk of serious personal injury.
Protect your hearing. Wear hearing protection during
extended periods of operation. Following this rule will
reduce the risk of serious personal injury.
Save these instructions. Refer to them frequently and
use them to instruct others who may use this tool. If you
loan someone this tool, loan them these instructions
also.
WARNING:
Some dust created by power sanding, sawing, grinding, drilling, and other construction activities contains chemicals
known to cause cancer, birth defects or other reproductive harm. Some examples of these chemicals are:
• lead from lead-based paints,
• crystalline silica from bricks and cement and other masonry products, and
• arsenic and chromium from chemically-treated lumber.
Your risk from these exposures varies, depending on how often you do this type of work. To reduce your exposure
to these chemicals: work in a well ventilated area, and work with approved safety equipment, such as those dust
masks that are specially designed to filter out microscopic particles.
5
Download from Www.Somanuals.com. All Manuals Search And Download.
SYMBOLS
Some of the following symbols may be used on this product. Please study them and learn their meaning. Proper
interpretation of these symbols will allow you to operate the product better and safer.
SYMBOL
NAME
DESIGNATION/EXPLANATION
V
Volts
Voltage
Current
A
Hz
W
Amperes
Hertz
Frequency (cycles per second)
Watt
Power
min
Minutes
Time
Alternating Current
Type of current
Direct Current
Type or a characteristic of current
Rotational speed, at no load
n
No Load Speed
o
Class II Tool
Per Minute
Double-insulated construction
Revolutions, strokes, surface speed, orbits etc., per minute
.../min
Do not expose to rain or use in damp locations.
Wet Conditions Alert
To reduce the risk of injury, user must read and understand
operator’s manual before using this product.
Read The Operator’s Manual
Always wear safety goggles, safety glasses with side shields, or
a full face shield when operating this product.
Eye Protection
Safety Alert
Precautions that involve your safety.
Failure to keep your hands away from the blade will result in seri-
ous personal injury.
No Hands Symbol
Failure to keep your hands away from the blade will result in
serious personal injury.
No Hands Symbol
No Hands Symbol
Failure to keep your hands away from the blade will result in
serious personal injury.
Failure to keep your hands away from the blade will result in
serious personal injury.
No Hands Symbol
Hot Surface
To reduce the risk of injury or damage, avoid contact with any
hot surface.
6
Download from Www.Somanuals.com. All Manuals Search And Download.
SYMBOLS
The following signal words and meanings are intended to explain the levels of risk associated with this product.
SYMBOL
SIGNAL
MEANING
Indicates an imminently hazardous situation, which, if not avoided, will
result in death or serious injury.
DANGER:
Indicates a potentially hazardous situation, which, if not avoided, could
result in death or serious injury.
WARNING:
CAUTION:
Indicates a potentially hazardous situation, which, if not avoided, may
result in minor or moderate injury.
(Without Safety Alert Symbol) Indicates a situation that may result in
property damage.
CAUTION:
SERVICE
WARNING:
Servicing requires extreme care and knowledge and should
be performed only by a qualified service technician. For
service we suggest you return the product to your nearest
AUTHORIZEDSERVICECENTERforrepair. Whenservicing,
use only identical replacement parts.
To avoid serious personal injury, do not attempt
to use this product until you read thoroughly and
understand completely the operator’s manual.
If you do not understand the warnings and
instructions in the operator’s manual, do not use
this product. Call RIDGID® customer service for
assistance.
WARNING:
The operation of any power tool can result in foreign objects being thrown into your eyes, which can result
in severe eye damage. Before beginning power tool operation, always wear safety goggles or safety glasses
with side shields and, when needed, a full face shield. We recommend Wide Vision Safety Mask for use
over eyeglasses or standard safety glasses with side shields. Always use eye protection which is marked
to comply with ANSI Z87.1.
SAVE THESE INSTRUCTIONS
7
Download from Www.Somanuals.com. All Manuals Search And Download.
ELECTRICAL
DOUBLE INSULATION
EXTENSION CORDS
Double insulation is a concept in safety in electric power
tools, which eliminates the need for the usual three-wire
grounded power cord. All exposed metal parts are isolated
from the internal metal motor components with protecting
insulation. Double insulated tools do not need to be
grounded.
When using a power tool at a considerable distance from
a power source, be sure to use an extension cord that has
the capacity to handle the current the tool will draw. An
undersized cord will cause a drop in line voltage, resulting in
overheating and loss of power. Use the chart to determine
the minimum wire size required in an extension cord. Only
round jacketed cords listed by Underwriter’s Laboratories
(UL) should be used.
WARNING:
When working outdoors with a tool, use an extension
cord that is designed for outside use. This type of cord is
designated with “W-A” or “W” on the cord’s jacket.
The double insulated system is intended to protect
the user from shock resulting from a break in the
product’s internal wiring. Observe all normal safety
precautions to avoid electrical shock.
Before using any extension cord, inspect it for loose or
exposed wires and cut or worn insulation.
NOTE: Servicing of a tool with double insulation requires
extreme care and knowledge of the system and should
be performed only by a qualified service technician. For
service, we suggest you return the tool to your nearest
authorized service center for repair. Always use original
factory replacement parts when servicing.
**Ampere rating (on tool data plate)
0-ꢀ.0
ꢀ.1-3.4 3.5-5.0 5.1-7.0 7.1-1ꢀ.0 1ꢀ.1-16.0
Cord Length
Wire Size (A.W.G.)
ꢀ5'
50'
16
16
16
16
16
16
16
16
14
16
14
1ꢀ
14
14
10
14
1ꢀ
—
ELECTRICAL CONNECTION
100'
This tool has a precision-built electric motor. It should be
connected to a power supply that is 120 volts, AC only
(normal household current), 60 Hz. Do not operate this
tool on direct current (DC). A substantial voltage drop will
cause a loss of power and the motor will overheat. If your
tool does not operate when plugged into an outlet, double-
check the power supply.
**Used on 12 gauge - 20 amp circuit.
NOTE: AWG = American Wire Gauge
WARNING:
Keep the extension cord clear of the working area.
Position the cord so that it will not get caught on
lumber, tools or other obstructions while you are
working with a power tool. Failure to do so can
result in serious personal injury.
WARNING:
Check extension cords before each use. If
damaged replace immediately. Never use tool with
a damaged cord since touching the damaged area
could cause electrical shock resulting in serious
injury.
8
Download from Www.Somanuals.com. All Manuals Search And Download.
FEATURES
PRODUCT SPECIFICATIONS
Cutting Depth at 51.5°...........................................1-5/8 in.
Input ................................ 1ꢀ0 V, AC only, 60 Hz, 15 Amps
No Load Speed ....................................5,800 r/min. (RPM)
Net Weight............................................................... 10 lbs.
Blade Diameter......................................................7-1/4 in.
Blade Arbor ..............................................................5/8 in.
Cutting Depth at 0°................................................ꢀ-3/8 in.
Cutting Depth at 45°..............................................1-3/4 in.
SPINDLE
LOCK
SwITCH
TRIGGER
DUST CHUTE
FRONT HANDLE
BLADE
HANDLE
DEPTH OF
CUT SCALE
BEvEL
ADJUSTMENT
LEvER
POSITIvE 56°
DEPTH
ADJUSTMENT
LEvER
STOP BUTTON
FULL LENGTH
KERF INDICATOR
1
4
3
8
1
2
UPPER
BLADE GUARD
5
8
3
4
1
2
1
ILLUMINATED PLUG
2
1
BLADE
wRENCH
STORAGE
LOwER
BLADE GUARD
6 mm BLADE wRENCH
Fig. 1
9
Download from Www.Somanuals.com. All Manuals Search And Download.
FEATURES
kNOW YOUR CIRCULAR SAW
ILLUMINATED PLUG
See Figure 1.
This saw is equipped with a plug that illuminates when
power is supplied to the tool. This allows the operator to
easily identify live tools.
The safe use of this product requires an understanding of
the information on the product and in this operator’s manual
as well as a knowledge of the project you are attempting.
Before use of this product, familiarize yourself with all
operating features and safety rules.
BLADE WRENCH STORAGE
Blade wrench storage is located on saw housing below the
cord exit. The storage area can be accessed by adjusting
the saw to a bevel position.
DUST CHUTE
To direct saw dust and chips away from the operator, a dust
chute is located on the side of the upper blade guard.
POWER CORD
The 1ꢀ-foot cord has a built-in cord wrap.
ERGONOMIC DESIGN
The design provides comfort when operating in different
positions and at different angles.
SPINDLE LOCk
The spindle lock allows you to secure the blade when turning
the blade screw.
FULL LENGTH kERF INDICATOR
Indicates blade position for more accurate cutting.
ASSEMBLY
UNPACkING
This product requires assembly.
WARNING:
Do not attempt to modify this product or create
accessories not recommended for use with this
product. Any such alteration or modification is
misuse and could result in a hazardous condition
leading to possible serious personal injury.
Carefully remove the product and any accessories from
the box. Make sure that all items listed in the packing list
are included.
Inspect the product carefully to make sure no breakage
or damage occurred during shipping.
Do not discard the packing material until you have carefully
inspected and satisfactorily operated the product.
WARNING:
If any parts are damaged or missing, please call
Do not connect to power supply until assembly
is complete. Failure to comply could result in
accidental starting and possible serious personal
injury.
1-866-539-1710 for assistance.
PACkING LIST
7-1/4 in. Circular Saw
Blade
6 mm Blade Wrench
Operator’s Manual
WARNING:
7-1/4 in. blade is the maximum blade capacity of
the saw. Also, never use a blade that is too thick
to allow outer blade washer to engage with the
flat on the spindle. Larger blades will come in
contact with the blade guides, while thicker blades
will prevent blade screw from securing blade on
spindle. Either of these situations could result in a
serious accident.
WARNING:
If any parts are damaged or missing, do not
operate this product until the parts are replaced.
Failure to heed this warning could result in serious
personal injury.
CAUTION:
To prevent damage to the spindle or spindle lock,
always allow motor to come to a complete stop
before engaging spindle lock.
10
Download from Www.Somanuals.com. All Manuals Search And Download.
ASSEMBLY
SPINDLE
LOCK
ATTACHING BLADE
See Figures 2 - 3.
Unplug the saw.
INNER
FLANGE
BUSHING
Depress and hold spindle lock.
Remove blade screw by turning it counterclockwise with
the 6 mm blade wrench, while keeping the spindle lock
button depressed.
BLADE
Remove outer blade washer (“D” washer).
WARNING:
If inner flange bushing has been removed, replace
it before placing blade on spindle. Failure to do
so will prevent blade from tightening properly and
could result in serious personal injury.
Retract the lower guard into the upper guard, making
sure the lower guard spring works properly, allowing the
guard to move freely.
SPINDLE
BLADE SCREw
OUTER BLADE wASHER
(“D” wASHER)
Check to see that the saw teeth and arrow on the saw
blade and the arrow on the lower guard are pointing in
the same direction.
Fig. ꢀ
SPINDLE
LOCK
NOTE: The saw teeth point upward at the front of the
saw as shown.
Fit the saw blade inside the lower blade guard and onto
the spindle.
Replace “D” washer.
Depress spindle lock and replace blade screw.
Tighten blade screw securely by turning it clockwise with
the 6 mm blade wrench.
NOTE: Never use a blade that is too thick to allow the
“D” washer to engage with the flats on the spindle.
REMOVING BLADE
See Figure 2 - 3.
Unplug the saw.
Depress and hold spindle lock.
Remove blade screw by turning it counterclockwise with
the provided 6 mm blade wrench, while keeping the
spindle lock depressed.
6 mm BLADE
wRENCH
TO
LOOSEN
TO
TIGHTEN
Remove outer blade washer (“D” washer).
Lift lower blade guard.
Fig. 3
Remove blade.
11
Download from Www.Somanuals.com. All Manuals Search And Download.
OPERATION
WARNING:
Do not allow familiarity with products to make you
careless. Remember that a careless fraction of a
second is sufficient to inflict serious injury.
WARNING:
Always wear safety goggles or safety glasses with
side shields when operating power tools. Failure
to do so could result in objects being thrown into
your eyes resulting in possible serious injury.
KICKBACK - BLADE SET TOO DEEP
Fig. 4
APPLICATIONS
You may use this product for the purposes listed below:
Cutting all types of wood products (lumber, plywood,
paneling, composition board, and hard board)
Cross cutting/Rip cutting
Bevel cutting
Pocket cutting
NOTE: The use of abrasive cut-off wheels is not recom-
mended for this saw.
kICkBACk
See Figures 4 - 7.
Kickback occurs when the blade stalls rapidly and the saw
is driven back towards you. Blade stalling is caused by any
action which pinches the blade in the wood.
INCORRECT SUPPORT
Fig. 5
DANGER:
LOwER BLADE GUARD IS IN UP
POSITION wHEN MAKING A CUT
Release switch immediately if blade binds or saw
stalls. Kickback could cause you to lose control
of the saw. Loss of control can lead to serious
personal injury.
To guard against kickback, avoid dangerous practices such
as the following:
Setting blade depth incorrectly.
Sawing into knots or nails in workpiece.
Twisting the blade while making a cut.
Making a cut with a dull, gummed up, or improperly set
blade.
Supporting the workpiece incorrectly.
Forcing a cut.
CORRECT BLADE DEPTH SETTING = LESS THAN A FULL
TOOTH OF THE BLADE TEETH SHOULD BE vISIBLE BELOw
Cutting warped or wet lumber.
Operating the tool incorrectly or misusing the tool.
Fig. 6
THE wORKPIECE.
To lessen the chance of kickback, follow these safety
practices:
Make straight cuts. Always use a straight edge guide
when rip cutting. This helps prevent twisting the blade.
Keep the blade at the correct depth setting. Less than a
full tooth of the blade teeth should be visible below the
workpiece.
Use clean, sharp, and properly set blades. Never make
cuts with dull blades.
Support the workpiece properly before beginning a
Inspect the workpiece for knots or nails before cutting.
cut.
Never saw into a knot or nail.
1ꢀ
Download from Www.Somanuals.com. All Manuals Search And Download.
OPERATION
Use steady, even pressure when making a cut. Never
force a cut.
Do not cut warped or wet lumber.
Hold the saw firmly with both hands and keep your body
in a balanced position so as to resist the forces if kickback
should occur.
WARNING:
When using the saw, always stay alert and exercise
control. Do not remove the saw from the workpiece
while the blade is moving.
SAW BLADES
The best of saw blades will not cut efficiently if they are not
kept clean, sharp, and properly set. Using a dull blade will
place a heavy load on the saw and increase the danger of
kickback. Keep extra blades on hand, so that sharp blades
are always available.
CORRECT SUPPORT
Fig. 7
LOwER BLADE GUARD IS IN UP
POSITION wHEN MAKING A CUT
Gum and wood pitch hardened on blades will slow the
saw down. Remove saw blade from the saw and use gum
and pitch remover, hot water, or kerosene to remove these
accumulations. DO NOT USE GASOLINE.
BLADE GUARD SYSTEM
See Figure 8.
The lower blade guard attached to the circular saw is there
for your protection and safety. Do not alter it for any reason.
If it becomes damaged, do not operate the saw until you
have the guard repaired or replaced. Always leave guard in
operating position when using the saw.
DANGER:
Fig. 8
When sawing through work, lower blade guard
does not cover blade on the underside of work.
Since blade is exposed on underside of work, keep
hands and fingers away from cutting area. Any part
of your body coming in contact with moving blade
will result in serious injury.
WARNING:
Never tie the lower blade guard in a raised position.
Leaving the blade exposed could lead to serious
injury.
If at any time the lower blade guard does not snap closed,
unplug the saw from the power supply. Exercise the lower
guard by moving it rapidly back and forth from the full open
position to the closed position several times. Normally this
will restore the guard to its normal operating condition. If
it does not correct a slow or sluggish closing lower guard,
do not use the saw. Take it to an authorized factory service
center for repair.
CAUTION:
To avoid possible serious injury, never use saw
when guard is not operating correctly. Check the
guard for correct operation before each use. The
guard is operating correctly when it moves freely,
and instantly returns to the closed position. If you
drop the saw, check the lower blade guard and
bumper for damage at all depth settings before
reuse.
13
Download from Www.Somanuals.com. All Manuals Search And Download.
OPERATION
STARTING/STOPPING THE SAW
See Figure 9.
To start the saw: Depress the switch trigger.
Always let the blade reach full speed, then guide the saw
into the workpiece.
SwITCH
TRIGGER
WARNING:
The blade coming in contact with the workpiece
before it reaches full speed could cause the saw
to “kickback” towards you resulting in serious
injury.
To stop the saw: Release the switch trigger.
After you release the switch trigger, allow the blade to come
to a complete stop. Do not remove the saw from the
workpiece while the blade is moving.
Fig. 9
ADJUSTING BLADE DEPTH
See Figure 10.
DEPTH OF
CUT SCALE
Always keep correct blade depth setting. Less than a
full tooth of the blade teeth should be visible below the
workpiece. More blade depth will increase the chance of
kickback and cause the cut to be rough.
1
3
1
2
5
8
INDEx
POINT
Unplug the saw.
3
4
Pull depth adjustment lever upward to release.
Determine the desired depth of cut.
1
1
2
Hold base flat against the workpiece and raise or lower
saw until the index point or mark on the saw aligns with
the desired depth on the scale.
2
2716
Push down on depth adjustment lever to lock into
position.
INDEXABLE LEVERS
See Figure 11.
DEPTH
ADJUSTMENT LEvER
The levers on the saw can be repositioned for the best
tightening position.
Fig. 10
Pull the lever out from the saw and to desired position.
Push lever back in and down to lock into place.
Check to be sure the base is clamped securely.
PUSH IN AND
DOwN TO LOCK
PULL OUT AND
UP TO POSITION
Fig. 11
14
Download from Www.Somanuals.com. All Manuals Search And Download.
OPERATION
OPERATING THE SAW
See Figures 12 - 14.
Itisimportanttounderstandthecorrectmethodforoperating
thesaw.Refertothefiguresinthissectiontolearnthecorrect
and incorrect ways for handling the saw.
WARNING:
To make sawing easier and safer, always maintain
proper control of the saw. Loss of control could
cause an accident resulting in possible serious
injury.
DANGER:
When lifting the saw from the workpiece, the blade
is exposed on the underside of the saw until the
lower blade guard closes. Make sure the lower
blade guard is closed before setting the saw
down.
Fig. 1ꢀ
To make the best possible cut, follow these helpful hints.
Hold the saw firmly with both hands.
Avoid placing your hand on the workpiece while making
a cut.
Support the workpiece so that the cut (kerf) is always to
your side.
Support the workpiece near the cut.
Clamp the workpiece securely so that the workpiece will
not move during the cut.
Always place the saw on the workpiece that is supported,
not the “cut off” piece.
Place the workpiece with the “good” side down.
Draw a guideline along the desired line of cut before
beginning the cut.
Keep the cord away from the cutting area. Always place
the cord to prevent it from hanging up on the workpiece
while making a cut.
Fig. 13
DANGER:
If the cord hangs up on the workpiece during a
cut, release the switch trigger immediately. Unplug
the saw and reposition the cord to prevent it from
hanging up again.
GUIDELINE
DANGER:
Using a saw with a damaged cord could result
in serious injury or death. If the cord has been
damaged, have it replaced before using the saw
again.
FULL LENGTH
KERF INDICATOR
Fig. 14
15
Download from Www.Somanuals.com. All Manuals Search And Download.
OPERATION
RIP CUTTING
See Figures 15 - 16.
Use a guide when making long or wide rip cuts with the
saw.
To rip cut using optional edge guide:
Slide the edge guide into the slot.
LOCK SCREw
Adjust the guide so that the "0" on the guide is aligned
with the edge of your workpiece.
Secure the guide with the lock screw provided with the
saw.
Secure the workpiece.
Position the face of the edge guide firmly against the edge
of workpiece.
NOTE: The guiding edge of the workpiece must be
straight for your cut to be straight. Use caution to prevent
the blade from binding in the cut.
EDGE GUIDE
Fig. 15
Saw along workpiece keeping guide firmly against edge
C-CLAMP
to achieve a straight rip cut.
To rip cut using a straight edge:
Secure the workpiece.
Clamp a straight edge to the workpiece using
STRAIGHT
EDGE
C-clamps.
Saw along the straight edge to achieve a straight rip
cut.
NOTE: Do not bind the blade in the cut.
BEVEL CUTTING
See Figures 17 - 19.
To make the best possible cut, follow these helpful hints:
Align the line of cut with the inner blade guide notch on
GUIDELINE
the base when making 45° bevel cuts.
Make a trial cut in scrap material along a guideline to
determine how much you should offset the guideline on
the cutting material.
wORKPIECE
C-CLAMP
Fig. 16
Adjust the angle of cut to any desired setting between
zero and 56°. Positive stops are located at 0°, 45° and 56°.
Refer to Adjusting Bevel Setting later in this manual.
56° BEvEL
BUTTON
NOTE: Push the positive 56° stop button in while raising
the motor housing to set the bevel setting above 45° and
up to 56°.
56
Adjusting Bevel Setting:
56
Unplug the saw.
Pull the bevel adjustment lever upward until the motor
housing moves freely.
0
Rotate motor housing end of saw until you reach the
desired angle setting on bevel scale.
NOTE: Positive stops are located at 0°, 45° and 56°.
Push the positive 56° stop button in while raising the
motor housing to set the bevel setting above 45° and up
to 56°.
BEvEL
ADJUSTMENT
LEvER
Push downward on the bevel adjustment lever until the
Fig. 17
motor housing is securely locked in place.
16
Download from Www.Somanuals.com. All Manuals Search And Download.
OPERATION
56°
BEvEL
SCALE
WARNING:
Attempting a bevel cut without having the bevel
adjustment lever securely locked in place can
result in serious injury.
ADJUSTMENT
BUTTON
56
56
Bevel Cutting:
Hold the saw firmly with both hands as shown.
Rest the front edge of the base on the workpiece.
Start the saw and let the blade reach full speed.
Guide the saw into the workpiece and make the cut.
0
Release the trigger and allow the blade to come to a
complete stop.
BEvEL
BLADE
GUIDE NOTCH
Lift the saw from the workpiece.
ADJUSTMENT
LEvER
POCkET CUTTING
See Figure 20.
GUIDELINE
Fig. 18
WARNING:
Always adjust bevel setting to zero before making
a pocket cut. Attempting a pocket cut at any other
setting can result in loss of control of the saw
possibly causing serious injury.
Adjust the bevel setting to zero.
Set the blade to the correct blade depth setting.
Swing the lower blade guard up using the lower blade
guard handle.
NOTE:Alwaysraisethelowerbladeguardwiththehandle
to avoid serious injury.
Hold the lower blade guard by the handle.
Rest the front of the base flat against the workpiece with
the rear of the handle raised so the blade does not touch
the workpiece.
Fig. 19
Start the saw and let the blade reach full speed.
Guide the saw into the workpiece and make the cut.
LOwER
BLADE GUARD
WARNING:
Always cut in a forward direction when pocket
cutting. Cutting in the reverse direction could
cause the saw to climb up on the workpiece and
back toward you.
Release the trigger and allow the blade to come to a
complete stop.
Lift the saw from the workpiece.
Clear corners out with a hand saw or sabre saw.
LOwER BLADE
GUARD HANDLE
Fig. ꢀ0
17
Download from Www.Somanuals.com. All Manuals Search And Download.
ADJUSTMENTS
COMBINATION
SQUARE
BLADE
WARNING:
Before performing any adjustment, make sure the
tool is unplugged from the power supply and the
switch is in the OFF position. Failure to heed this
warning could result in serious personal injury.
TORx® T-8
ADJUSTMENT
SCREw
POSITIVE 0° BEVEL STOP
See Figures 21 - 22.
The saw has a positive 0° bevel stop that has been factory
adjustedtoassure0°angleofthesawbladewhenmaking90°
cuts. However, misalignment can occur during shipping.
To check positive 0° bevel stop:
Unplug the saw.
Place the saw in an upside down position on a
workbench.
TORx® T-8
wRENCH
Move the lower blade guard out of the way so that the
saw blade is exposed.
TORx® T-8
ADJUSTMENT
SCREw
Check the squareness of the saw blade to the base of
the saw using a combination square.
Fig. ꢀ1
To adjust positive 0° bevel stop:
Unplug the saw.
Pull bevel adjustment lever upward to release.
TurnTORX® T-8adjustmentscrewwithTORX® T-8wrench
and adjust base until it is square with the saw blade.
56
Securely lock the bevel adjustment lever.
56
WARNING:
Attempting a bevel cut without having the bevel
adjustment lever securely locked in place can
result in serious injury.
0
POSITIvE 0º
BEvEL STOP
TORx® T-8
ADJUSTMENT
SCREw
BEvEL
ADJUSTMENT LEvER
Fig. ꢀꢀ
18
Download from Www.Somanuals.com. All Manuals Search And Download.
MAINTENANCE
Electric tools used on fiberglass material, wallboard,
spackling compounds, or plaster are subject to accelerated
wear and possible premature failure because the fiberglass
chips and grindings are highly abrasive to bearings, brushes,
commutators, etc. Consequently, we do not recommend
using this tool for extended work on these types of materials.
However, if you do work with any of these materials, it is
extremely important to clean the tool using compressed
air.
WARNING:
When servicing use only identical RIDGID®
replacement parts. Use of any other parts may
create a hazard or cause product damage.
WARNING:
Always wear safety goggles or safety glasses with
side shields during power tool operation or when
blowing dust. If operation is dusty, also wear a
dust mask.
LUBRICATION
All of the bearings in this product are lubricated with a
sufficient amount of high grade lubricant for the life of the
unit under normal operating conditions. Therefore, no further
lubrication is required.
GENERAL MAINTENANCE
Avoid using solvents when cleaning plastic parts. Most
plastics are susceptible to damage from various types of
commercial solvents and may be damaged by their use. Use
clean cloths to remove dirt, dust, oil, grease, etc.
POWER SUPPLY CORD REPLACEMENT
If replacement of the power supply cord is necessary, this
has to be done by the manufacturer or his agent in order to
avoid a safety hazard.
WARNING:
Do not at any time let brake fluids, gasoline,
petroleum-based products, penetrating oils, etc.,
come in contact with plastic parts. Chemicals can
damage, weaken or destroy plastic which may
result in serious personal injury.
ACCESSORIES
To order these accessories, call 1-866-539-1710.
Edge Guide.......................................................................................................................................................690119003
WARNING:
Current attachments and accessories available for use with this product are listed above. Do not use any
attachments or accessories not recommended by the manufacturer of this product. The use of attachments or
accessories not recommended can result in serious personal injury.
19
Download from Www.Somanuals.com. All Manuals Search And Download.
NOTES
ꢀ0
Download from Www.Somanuals.com. All Manuals Search And Download.
WARRANTY
RIDGID® HAND HELD AND STATIONARY POWER TOOL
3 YEAR LIMITED SERVICE WARRANTY
Proof of purchase must be presented when requesting war-
ranty service.
WHAT IS NOT COVERED
This warranty applies only to the original purchaser at retail
and may not be transferred. This warranty only covers de-
fects arising under normal usage and does not cover any
malfunction, failure or defect resulting from misuse, abuse,
neglect, alteration, modification or repair by other than an
authorized service center for RIDGID® branded hand held
and stationary power tools. Consumable accessories pro-
vided with the tool such as, but not limited to, blades, bits
and sand paper are not covered.
Limited to RIDGID® hand held and stationary power tools
purchased ꢀ/1/04 and after. This product is manufactured
by One World Technologies, Inc. The trademark is licensed
from RIDGID, Inc. All warranty communications should be
directed to One World Technologies, Inc., attn: RIDGID Hand
Held and Stationary Power Tool Technical Service at (toll
free) 1-866-539-1710.
90-DAY SATISFACTION GUARANTEE POLICY
During the first 90 days after the date of purchase, if you are
dissatisfied with the performance of this RIDGID® Hand Held
and Stationary Power Tool for any reason you may return
the tool to the dealer from which it was purchased for a full
refund or exchange. To receive a replacement tool you must
present proof of purchase and return all original equipment
packaged with the original product. The replacement tool
will be covered by the limited warranty for the balance of
the 3 YEAR service warranty period.
RIDGID, INC. AND ONE WORLD TECHNOLOGIES, INC.
MAkE NO WARRANTIES, REPRESENTATIONS OR
PROMISES AS TO THE QUALITY OR PERFORMANCE
OF ITS POWER TOOLS OTHER THAN THOSE SPECIFI-
CALLY STATED IN THIS WARRANTY.
ADDITIONAL LIMITATIONS
To the extent permitted by applicable law, all implied war-
ranties, including warranties of MERCHANTABILITY or FIT-
NESS FOR A PARTICULAR PURPOSE, are disclaimed. Any
implied warranties, including warranties of merchantability
or fitness for a particular purpose, that cannot be disclaimed
under state law are limited to three years from the date of
purchase. One World Technologies, Inc. and RIDGID, Inc.
are not responsible for direct, indirect, incidental or conse-
quential damages. Some states do not allow limitations on
how long an implied warranty lasts and/or do not allow the
exclusion or limitation of incidental or consequential dam-
ages, so the above limitations may not apply to you. This
warranty gives you specific legal rights, and you may also
have other rights which vary from state to state.
WHAT IS COVERED UNDER THE 3 YEAR
LIMITED SERVICE WARRANTY
This warranty on RIDGID® Hand Held and Stationary Power
Tools covers all defects in workmanship or materials and nor-
mal wear items such as brushes, chucks, motors, switches,
cords, gears and even cordless batteries in this RIDGID®
tool for three years following the purchase date of the tool.
Warranties for other RIDGID® products may vary.
HOW TO OBTAIN SERVICE
To obtain service for this RIDGID® tool you must return it;
freight prepaid, or take it in to an authorized service center
for RIDGID® branded hand held and stationary power tools.
You may obtain the location of the authorized service center
nearest you by calling (toll free) 1-866-539-1710 or by log-
ging on to the RIDGID® website at www.ridgid.com. When
requesting warranty service, you must present the original
dated sales receipt. The authorized service center will re-
pair any faulty workmanship, and either repair or replace
any part covered under the warranty, at our option, at no
charge to you.
One World Technologies, Inc.
P.O. Box 35, Hwy. 8
Pickens, SC ꢀ9671
ꢀ1
Download from Www.Somanuals.com. All Manuals Search And Download.
OPERATOR’S MANUAL
7-1/4 in. CIRCULAR SAW
DOUBLE INSULATED
R3202
Customer Service Information:
For parts or service, contact your nearest RIDGID authorized service center. Be
sure to provide all relevant information when you call or visit. For the location of
the authorized service center nearest you, please call 1-866-539-1710 or visit us
The model number of this tool is found on a plate attached to the motor housing.
Please record the serial number in the space provided below. When ordering repair
parts, always give the following information:
R3ꢀ0ꢀ
Model No.
Serial No.
987000-316
5-ꢀ7-08 (REV: 01)
Download from Www.Somanuals.com. All Manuals Search And Download.
|