OPERATOR'S MANUAL
13 in. THICKNESS PLANER
TP1300LS
6
15
14
5
13
12
11
4
10
9
3
8
7
6
2
5
ut
4
1
Ind
I
Cut
"
1
3
1
1/8
3/32
3
2.5
2
1
4
8
1.5
1
Repeat 3
2
2
.5
0
1/16
1/32
0
4
1
4
1
1
1
2
1
"
3
0
1
1
0
4
Your new planer has been engineered and manufactured to our high standards for dependability, ease of operation, and
operator safety. When properly cared for, it will give you years of rugged, trouble-free performance.
WARNING:
To reduce the risk of injury, the user must read and understand the operator’s manual before using this product.
Thank you for buying a Ridgid product.
SAVE THIS MANUAL FOR FUTURE REFERENCE
Download from Www.Somanuals.com. All Manuals Search And Download.
SYMBOLS
The purpose of safety symbols is to attract your attention to possible dangers. The safety symbols, and the
explanations with them, deserve your careful attention and understanding. The safety warnings do not by themselves
eliminate any danger. The instructions or warnings they give are not substitutes for proper accident prevention
measures.
SYMBOL MEANING
DANGER: Indicates an imminently hazardous situation, which, if not avoided, will result in death or serious
injury.
WARNING: Indicates a potentially hazardous situation, which, if not avoided, could result in death or serious
injury.
CAUTION: Indicates a potentially hazardous situation, which, if not avoided, may result in minor or moderate
injury. It may also be used to alert against unsafe practices that may cause property damage.
Note:
Advises you of additional information concerning the operation or maintenance of the equipment.
SAFETY AND INTERNATIONAL SYMBOLS
This operator's manual describes safety and international symbols and pictographs that may appear on this product.
Read the operator's manual for complete safety, assembly, operating and maintenance, and repair information.
SYMBOL
NAME
MEANING
Wet Condition Alert
• Do not expose to rain or use in damp locations.
• Failure to keep your hands away from the blade will result in
serious personal injury.
No Hands Symbol
• Toreducetheriskofinjury, theusermustreadand understand
the operator’s manual before using this product.
Read the Operator’s Manual
Eye Protection
• Always wear safety goggles or safety glasses with side shields
and a full face shield when operating this product.
RULES FOR SAFE OPERATION
ꢀ GUARD AGAINST ELECTRICAL SHOCK by preventing
body contact with grounded surfaces such as pipes,
radiators, ranges, refrigerator enclosures.
Safe operation of this power tool requires that you read and
understand this operator's manual and all labels affixed to
the tool. Safety is a combination of common sense, staying
alert, and knowing how your planer works.
ꢀ KEEP GUARDS IN PLACE and in good working order.
ꢀ REMOVE WRENCHES AND ADJUSTING KEYS. Get
in the habit - before turning on tool - that hex keys and
adjusting wrenches are removed from tool.
READ ALL INSTRUCTIONS
ꢀ KNOW YOUR POWER TOOL. Read the operator's
manual carefully. Learn the planer's applications and
limitations as well as the specific potential hazards related
to this tool.
3
Download from Www.Somanuals.com. All Manuals Search And Download.
RULES FOR SAFE OPERATION
ꢀ KEEP THE WORK AREA CLEAN. Cluttered work areas
and work benches invite accidents. DO NOT leave tools
or pieces of wood on the planer while it is in operation.
ꢀ MAINTAIN TOOLS WITH CARE. Keep tools sharp and
clean for better and safer performance. Follow instructions
for lubricating and changing accessories.
ꢀ DO NOT USE IN DANGEROUS ENVIRONMENTS. Do
not use power tools near gasoline or other flammable
liquids, in damp or wet locations, or expose them to rain.
Keep the work area well lit.
ꢀ DISCONNECT ALL TOOLS. When not in use, before
servicing, or when changing attachments, all tools should
be disconnected.
ꢀ AVOID ACCIDENTAL STARTING. Be sure switch is off
ꢀ KEEP CHILDREN AND VISITORS AWAY. All visitors
should wear safety glasses and be kept a safe distance
from work area. Do not let visitors contact tool or extension
cord while operating.
when plugging in any tool.
ꢀ USE RECOMMENDED ACCESSORIES. Consult the
operator's manual for recommended accessories. The
use of improper accessories may cause risk of injury.
ꢀ MAKE WORKSHOP CHILDPROOF with padlocks and
ꢀ NEVER STAND ON TOOL. Serious injury could occur if
master switches or by removing starter keys.
the tool is tipped or if the blade is unintentionally contacted.
ꢀ DO NOT FORCE THE TOOL it will do the job better and
ꢀ CHECK DAMAGED PARTS. Before using the tool, a
guard or other part that is damaged should be carefully
checked to determine that it will operate properly and
perform its intended function. Check for alignment of
moving parts, binding of moving parts, breakage of parts,
mounting and any other conditions that may affect its
operation. A guard or other part that is damaged must be
properly repaired or replaced by an authorized service
center to avoid risk of personal injury.
safer at the rate for which it was designed.
ꢀ USE THE RIGHT TOOL FOR THE JOB. Do not force
the tool or attachment to do a job it was not designed for.
Use it only the way it was intended.
ꢀ USE THE PROPER EXTENSION CORD. Make sure
your extension cord is in good condition. Use only a cord
heavy enough to carry the current your product will draw.
An undersized cord will cause a drop in line voltage
resulting in loss of power and overheating. A wire gage
size (A.W.G.) of at least 14 is recommended for an
extension cord 25 feet or less in length. If in doubt, use
the next heavier gage. The smaller the gage number, the
heavier the cord.
ꢀ DIRECTION OF FEED. Feed work into a blade or cutter
against the direction or rotation of the blade or cutter
only.
ꢀ NEVER LEAVE TOOL RUNNING UNATTENDED, TURN
THE POWER OFF. Do not leave tool until it comes to a
complete stop.
ꢀ INSPECT TOOL CORDS AND EXTENSION CORDS
PERIODICALLY and, if damaged, have repaired at your
nearest authorized service center. Stay constantly aware
of cord location and keep it well away from the moving
blade.
ꢀ FIRMLY CLAMP OR BOLT your tool to a workbench or
table at approximately hip height.
ꢀ KEEP HANDS AWAY FROM CUTTING AREA. Do not
reach underneath work or in blade cutting path with your
hands and fingers for any reason. Always turn the power
off.
ꢀ DRESS PROPERLY. Do not wear loose clothing, gloves,
neckties, rings, bracelets, or other jewelry that can get
caught and draw you into moving parts. Nonslip footwear
is recommended. Also wear protective hair covering to
contain long hair.
ꢀ DO NOT ABUSE CORD. Never yank cord to disconnect
it from receptacle. Keep cord from heat, oil, and sharp
edges.
ꢀ ALWAYS WEAR SAFETY GLASSES WITH SIDE
SHIELDS. Everyday eyeglasses have only impact-
resistant lenses; they are NOT safety glasses.
ꢀ USE ONLY OUTDOOR EXTENSION CORDS. Use only
extension cords with the marking "Acceptable for use
with outdoor appliances; store cords indoors while not in
use". Use extension cords with an electrical rating not
less than the planer's electrical rating. Always disconnect
the extension cord from the outlet before disconnecting
the product from the extension cord.
ꢀ WEAR A DUST MASK to keep from inhaling fine
particles.
ꢀ PROTECT YOUR HEARING. Wear hearing protection
during extended periods of operation.
ꢀ SECURE WORK. Use clamps or a vise to hold work
when practical. It's safer than using your hand and frees
both hands to operate tool.
ꢀ DO NOT USE TOOL IF SWITCH DOES NOT TURN IT
ON AND OFF. Have defective switches replaced by an
authorized service center.
ꢀ DO NOT OVERREACH. Keep proper footing and balance
ꢀ KEEP TOOL DRY, CLEAN, AND FREE FROM OIL
AND GREASE. Always use a clean cloth when cleaning.
Never use brake fluids, gasoline, petroleum-based
products, or any solvents to clean tool.
at all times.
4
Download from Www.Somanuals.com. All Manuals Search And Download.
RULES FOR SAFE OPERATION
ꢀ NEVER USE THIS TOOL IN AN EXPLOSIVE
ATMOSPHERE. Normal sparking of the motor could
ignite fumes.
ꢀ NEVER PERFORM THE PLANING OPERATION with
the cutter head or cutter guard removed.
ꢀ NEVER MAKE A PLANING CUT deeper than 1/8 in.
ꢀ IF ANY PART OF THIS TOOL IS MISSING or should
break, bend, or fail in any way, or should any electrical
component fail to perform properly, shut off the power
switch, remove the plug from the power source and have
damaged, missing, or failed parts replaced before
resuming operation.
(3 mm).
ꢀ DO NOT PLANE MATERIAL shorter than 14 in.
(356 mm) or narrower than 3/4 in. (19 mm).
ꢀ MAINTAIN THE PROPER RELATIONSHIP between the
infeed and outfeed surfaces and the cutter head blade
path.
ꢀ DO NOT OPERATE THIS TOOL WHILE UNDER THE
INFLUENCE OF DRUGS, ALCOHOL, OR ANY
MEDICATION.
ꢀ SUPPORT THE WORKPIECE ADEQUATELY at all
times during operation; maintain control of the work at all
times.
ꢀ ALWAYS STAY ALERT! Do not allow familiarity (gained
from frequent use of your planer) to cause a careless
mistake. ALWAYS REMEMBER that a careless fraction
of a second is sufficient to inflict serious injury.
ꢀ DO NOT BACK THE WORK toward the infeed table.
ꢀ DO NOT ATTEMPT TO PERFORM an abnormal or little
used operation without the use of sturdy and adequate
jigs, fixtures, stops, and the like.
ꢀ STAY ALERT AND EXERCISE CONTROL. Watch what
you are doing and use common sense. Do not operate
tool when you are tired. Do not rush.
ꢀ NEVER plane more than one piece at a time. DO NOT
PLANE more than one workpiece on the planer table at
a time.
ꢀ MAKE SURE THE WORK AREA HAS AMPLE
LIGHTING to see the work and that no obstructions will
interfere with safe operation BEFORE performing any
work using your planer.
ꢀ BEFORE STARTING UP, recheck to make certain all
holding screws are tight.
ꢀ STOP THE MACHINE and recheck the hex head bolts
and blades for tightness after about 50 hours of operation.
ꢀ ALWAYS TURN OFF THE TOOL before disconnecting
it to avoid accidental starting when reconnecting to power
supply. NEVER leave the tool unattended while connected
to a power source.
ꢀ DO NOT FORCE FEED THE WORKPIECE through the
machine. Let the planer apply the proper feed rate.
ꢀ CHECK THE FEED ROLLERS occasionally to be sure
ꢀ SAVE THESE INSTRUCTIONS. Refer to them frequently
and use them to instruct other users. If you loan someone
this tool, loan them these instructions also.
there are no chips or sawdust between any components.
ꢀ PLANE ONLY SOUND LUMBER; there should be no
loose knots and as few tight knots as possible. Make
sure the workpiece is free from nails, screws, stones, or
other foreign objects that could break or chip the blades.
WARNING:
ꢀ NEVER STAND DIRECTLY IN LINE with either the infeed
Some dust created by power sanding, sawing,
grinding, drilling, and other construction activities
contains chemicals known to cause cancer, birth
defectsorotherreproductiveharm. Someexamples
of these chemicals are:
or outfeed sides. Stand off to one side.
ꢀ MAKE SURE THE BLADES ARE ATTACHED as
described in the operation section. The blades are sharp
and can easily cut your hand. Use caution in handling
the blades and cutter head guard.
•
•
lead from lead-based paints,
crystalline silica from bricks and cement and
other masonry products, and
ꢀ NEVER PUT YOUR FINGERS into the dust chute or
under the cutter guard.
•
arsenic and chromium from chemically-treated
ꢀ ALLOW THE CUTTER HEAD to reach full speed before
using the planer.
lumber.
ꢀ REPLACEMENT PARTS. All repairs, whether electrical
or mechanical, should be made at your nearest authorized
service center.
Your risk from these exposures varies, depending
on how often you do this type of work. To reduce
your exposure to these chemicals, work in a well
ventilated area and work with approved safety equip-
ment, such as those dust masks that are specially
designed to filter out microscopic particles.
ꢀ DO NOT attempt to turn cutter head with hands.
ꢀ WHEN SERVICING, use only identical replacement parts.
Use of any other parts may create a hazard or cause
product damage.
SAVE THESE INSTRUCTIONS
5
Download from Www.Somanuals.com. All Manuals Search And Download.
ELECTRICAL
GROUNDING INSTRUCTIONS
EXTENSION CORDS
In the event of a malfunction or breakdown, grounding
provides a path of least resistance for electric current to
reducetheriskofelectricshock. Thistoolisequippedwithan
electric cord having an equipment-grounding conductor and
a grounding plug. The plug must be plugged into a matching
outlet that is properly installed and grounded in accordance
with all local codes and ordinances.
Useonly3-wireextensioncordsthathave3-pronggrounding
plugs and 3-pole receptacles that accept the tool's plug.
When using a power tool at a considerable distance from the
power source, use an extension cord heavy enough to carry
the current that the tool will draw. An undersized extension
cord will cause a drop in line voltage, resulting in a loss of
power and causing the motor to overheat. Use the chart
provided below to determine the minimum wire size required
in an extension cord. Only round jacketed cords listed by
Underwriter's Laboratories (UL) should be used.
Donotmodifytheplugprovided. Ifitwillnotfittheoutlet, have
the proper outlet installed by a qualified electrician. Improper
connectionoftheequipment-groundingconductorcanresult
in a risk of electric shock. The conductor with insulation
having an outer surface that is green with or without yellow
stripes is the equipment-grounding conductor. If repair or
replacement of the electric cord or plug is necessary, do not
connect the equipment-grounding conductor to a live
terminal.
Length of Extension Cord
Up to 25 feet
Wire Size (A.W.G.)
14
12
26-50 feet
When working with the tool outdoors, use an extension cord
that is designed for outside use. This is indicated by the
letters WA on the cord's jacket.
Check with a qualified electrician or service personnel if the
groundinginstructionsarenotcompletelyunderstood, orifin
doubt as to whether the tool is properly grounded.
Before using an extension cord, inspect it for loose or
exposed wires and cut or worn insulation. Repair or replace
a damaged or worn cord immediately.
Repair or replace a damaged or worn cord immediately.
This tool is intended for use on a circuit that has an outlet like
the one shown in Figure 1. It also has a grounding pin like the
one shown.
CAUTION:
Keep the extension cord clear of the working area.
Position the cord so that it will not get caught on
lumber, tools or other obstructions while you are
working with a power tool.
WARNING:
Check extension cords before each use. If dam-
aged replace immediately. Never use tool with a
damaged cord since touching the damaged area
could cause electrical shock resulting in serious
injury.
GROUNDING
PIN
ELECTRICAL CONNECTION
Your Planer is powered by a precision built electric motor. It
should be connected to a power supply that is 120 volts,
60 Hz. If the machine does not operate when plugged into an
outlet, double check the power supply.
COVER OF GROUNDED
OUTLET BOX
Fig. 1
6
Download from Www.Somanuals.com. All Manuals Search And Download.
GLOSSARY OF TERMS FOR PLANERS
Planing
Cutter Head
A rotating piece with adjustable blades. The cutter head
removes material from the workpiece.
Removing wood from the widest surface or face of a board
so as to make it flat and smooth.
Resin
Depth of Cut
A term used to indicate how deep the cutter blades cut into
the workpiece.
A sticky, sap base substance that has hardened.
Revolutions Per Minute (RPM)
Gum
The number of turns completed by a spinning object in one
minute.
A sticky, sap based residue from wood products.
Infeed Table Extension
Snipe
The infeed table extension is where the workpiece is placed
before being picked up by the feed rollers.
A depression made at either end of a workpiece by the cutter
blades when the board is not properly supported.
Kickback
Throw-Back
Throwing of a workpiece in a manner similar to a kickback.
Usually associated with a cause other than the kerf closing,
such as a workpiece being pushed into the rotating cutter
head assembly.
An uncontrolled grabbing and throwing of the workpiece
back toward the operator by the rotating cutter head.
Leading End
The end of the workpiece which is pushed into the cutter
head first.
Trailing End
The end of the workpiece which is last planed by the cutter
head.
Outfeed Table Extension
The outfeed table extension is what supports the workpiece
after it has passed under the cutter blades.
Workpiece
The item on which the cutting operation is being performed.
The surfaces of a workpiece are commonly referred to as
faces, end, and edges.
Planer Table
The combination of infeed and outfeed table surfaces which
support the workpiece during a cutting operation.
FEATURES
SPECIFICATIONS
Feed Rate .................................................................................................................................................................. 26 FPM
Input ......................................................................................................................... 120 volts, 60Hz, AC Only, 15 Amperes
No Load Speed .......................................................................................................................................................9,000/min
Max. Planing Height........................................................................................................................................ 6 in. (152 mm)
Max. Planing Width ....................................................................................................................................... 13 in. (330 mm)
Max. Planing Depth ......................................................................................................................................... 1/8 in. (3 mm)
Net Weight .................................................................................................................................................. 85 lbs. (38.6 kg.)
7
Download from Www.Somanuals.com. All Manuals Search And Download.
FEATURES
KNOW YOUR PORTABLE PLANER
RESET BUTTON
Opens the power line circuit when the motor temperature
exceeds a safe level, when the motor is overloaded, or
when a lower voltage condition exists.
See Figure 2.
Before attempting to use your planer, familiarize yourself
with all operating Features and Rules for Safe Operation.
SCALE
Quickly check the thickness of a workpiece.
WARNING:
Do not allow familiarity with your tool to make you
careless. Remember that a careless fraction of a
second is sufficient to inflict severe injury.
SURE CUT™
Firmly locks the cutter head assembly to help eliminate
snipe.
SWITCH AND SWITCH KEY
15 AMP MOTOR
Your planer has an easy access power switch. To lock in the
OFF position, remove the switch key. Place the key in a
location inaccessible to children and others not qualified to
use the tool.
Your planer has a powerful 15 amp motor with sufficient
power to handle tough cutting jobs.
AUTOMATIC FEED
Infeed and outfeed rollers feed the wood through the planer.
TABLE EXTENSIONS
Infeed and outfeed table extensions are attached to the
machine and fold "upright" for easy storage. These table
extensions are helpful when planing long workpieces.
DEPTH ADJUSTMENT HANDWHEEL
The depth adjustment handwheel is used to raise and lower
the cutter head assembly.
THICKNESS SCALE
The thickness scale accurately displays the height of the
cutter blades to a maximum of 6 in. (152 mm).
DEPTH GAGE
A depth gage is located on the front of your planer and
measures depth of cuts up to 1/8 in. (3 mm).
TOOL STORAGE
For your convenience, a magnetic blade tool, 4 mm hex key,
8 mm/10 mm wrench, and blade changing instructions are
located in the tool storage area on the side of the planer.
REPEAT-A-CUT™
TheRepeat-A-Cut™,locatedontherightsideofthemachine
housing, has preset measurements for repetitive planing.
K
O
SCALE
SURE-CUT™
TOOL STORAGE
RESET
BUTTON
DEPTH ADJUSTMENT
HANDWHEEL
6
15
SWITCH AND
SWITCH KEY
14
5
13
12
11
4
10
9
3
8
7
6
2
REPEAT-A-CUT™
5
4
DEPTH GAGE
Ind
1
3
2
ut
1
I
Cut
3
1/8
3/32
2.5
2
"
1
1.5
1
1
4
8
.5
0
Repeat 3
1/16
1/32
0
1
2
1
4
1
4
0
1
2
1
0
"
3
1
1
4
INFEED TABLE
EXTENSION
THICKNESS SCALE
Fig. 2
8
Download from Www.Somanuals.com. All Manuals Search And Download.
UNPACKING
Your planer has been shipped completely assembled
except for the dust chute and handwheel knob.
ꢀ Do not discard the packing materials until you have
carefully inspected the tool, identified all loose parts, and
satisfactorily operated your new tool.
NOTE:Every Ridgid Thickness Planer is tested at the factory
to insure its performance. You may see small amounts of
wood dust and chips on your new planer.
ꢀ Examine all parts to make sure no breakage or damage
has occurred during shipping.
ꢀ If any parts are damaged or missing, please call
ꢀ Remove all loose parts from the carton. Separate and
1-866-539-1710 for assistance.
check with the list of loose parts. See Figure 4.
ꢀ Remove the packing materials from around your tool.
ꢀ Carefully lift tool from the carton and place it on a level
work surface. This tool is heavy. To avoid back injury,
get help when needed.
WARNING:
If any parts are missing, do not operate this tool
until the missing parts are replaced. Failure to do so
could result in possible serious personal injury.
ꢀ Remove the protective oil that is applied to all unpainted
metal surfaces. Use any ordinary household type grease
and spot remover
TOOLS NEEDED
The following tools (not included) are needed for checking adjustments of your planer:
13 mm COMBINATION WRENCH (2)
FRAMING SQUARE
Fig. 3
9
Download from Www.Somanuals.com. All Manuals Search And Download.
LOOSE PARTS LIST
The following items are included with your Planer:
ꢀ Upper Brace, long (2)
ꢀ Upper Brace, short (2)
ꢀ Lower Brace, long (2)
ꢀ Lower Brace, short (2)
ꢀ Upper Leg (4)
ꢀ Magnetic Blade Wrench
ꢀ Hardware Pack includes:
32 - carriage bolt, M8 x 1-1/4 in. x 16
4 - hex bolt, M8 x 1-1/4 in. x 65
36 - flanged hex nut, M8 x 1-1/4 in.
4 - flat washer
ꢀ Lower Leg (4)
ꢀ Dust Chute
ꢀ Foot (4)
ꢀ Handwheel Knob
ꢀ Screw
ꢀ Switch Key
ꢀ Wrench
ꢀ Operator's Manual
ꢀ Hex Key
HEX BOLT
CARRIAGE BOLT
UPPER BRACE, SHORT
FLAT WASHER
FLANGED HEX NUT
UPPER BRACE, LONG
LOWER BRACE, SHORT
MAGNETIC
BLADE
WRENCH
LOWER BRACE, LONG
SWITCH KEY
K
E
O
PULL OUT TO LOCK
HANDWHEEL KNOB
SCREW
HEX KEY
WRENCH
DUST CHUTE
LOWER LEG
FOOT
UPPER LEG
Fig. 4
WARNING:
The use of attachments or accessories not listed might be hazardous and could cause serious personal injury.
10
Download from Www.Somanuals.com. All Manuals Search And Download.
ASSEMBLY
ꢀ Next, attach lower leg piece to the inside of upper leg
piece placing lower brace on top of both leg pieces (also
on the inside of the leg stand). Insert two carriage bolts
and hand tighten using hex nuts.
ASSEMBLING LEG STAND
See Figures 5 and 6.
ꢀ Separate brace pieces from leg pieces. There are a total
of 16 pieces: 8 brace pieces and 8 leg pieces.
ꢀ Repeat the above steps once.
ꢀ Remove the following hardware from the hardware bag:
This completes two of the four sides of the leg stand.
ꢀ Place upper brace, short, inside upper leg piece.
32 carriage bolts (M8 x 1-1/4 in.)
4 rubber feet
4 hex bolts (M8 x 1-1/4 in. x 65)
4 flat washers
36 flanged hex nuts (M8 x 1-1/4 in.)
NOTE: Upper brace, short, has two large, oval holes in
each end; these holes should be on top when leg stand
is completely assembled.
ꢀ Place upper brace, long, inside upper leg piece.
ꢀ Align holes on upper brace, long, with the holes on the
upper leg piece. Insert two carriage bolts and hand
tighten using hex nuts.
NOTE: Upper brace has two large, oval holes in each
end; these holes should be on top when leg stand is
completely assembled as shown in figure 5.
ꢀ Repeat the above step on the opposite side.
ꢀ Align holes on the upper brace with the holes on the leg
piece. Insert two carriage bolts and hand tighten using
hex nuts.
ꢀ On the inside of the leg stand, place lower brace, short,
on top of both the upper and lower leg pieces. Insert two
carriage bolts and hand tighten using hex nuts.
ꢀ Place lower leg piece inside upper leg brace. Place
ꢀ Repeat the above step on the opposite side.
lower brace, long, on top of both leg pieces.
ꢀ Place one rubber foot on the bottom of each lower leg
ꢀ Align holes on all three pieces. Insert two carriage bolts
piece.
and hand tighten using hex nuts.
ꢀ Using a wrench, securely tighten all hex nuts.
ꢀ Attach a second upper leg piece to the outside of upper
This completes the leg stand.
brace using two carriage bolts and hex nuts.
HEX NUT
UPPER BRACE,
SHORT
CARRIAGE BOLT
UPPER BRACE,
LONG
CARRIAGE
BOLT
UPPER LEG
LOWER
BRACE,
LONG
LOWER LEG
LOWER
BRACE, SHORT
RUBBER FOOT
Fig. 5
11
Download from Www.Somanuals.com. All Manuals Search And Download.
ASSEMBLY
UPPER
BRACE,
SHORT
UPPER
BRACE,
LONG
WARNING:
To prevent accidental starting that could cause pos-
sible serious personal injury, assemble all parts,
make sure all adjustments are complete, and make
sure all fasteners are secure before connecting tool
to power supply. The tool should never be con-
nected to power supply when you are assembling
parts, making adjustments, installing or removing
blades, or when not in use.
INSTALLING HANDWHEEL KNOB
See Figure 6.
LOWER LEG
LOWER
BRACE,
SHORT
ꢀ Remove the handwheel knob and screw from the
hardware bag.
ꢀ Turn the depth adjustment handwheel until the hole for
the handwheel knob is aligned with the slot in the planer
housing.
Fig. 7
ꢀ Place the handwheel knob over the hole and tighten it
using the screw.
MOUNTING THE PLANER TO THE LEG STAND
See Figure 8.
ꢀ Turn leg stand upright as shown in figure 7.
ꢀ Carefully place planer on the top of the leg stand. Align
holes in the planer base with the holes in the leg stand.
ꢀ Insert the hex bolts in each of the four holes and secure
6
15
14
HEX
BOLT
5
13
using flat washers and hex nuts.
12
11
4
10
9
3
8
ꢀ Tighten all hardware with wrenches. You may find it
helpful to use one wrench to hold the head of the bolt
and one to tighten the hex nut.
7
6
2
5
4
ut
8
1"
1
4
1
Repeat3
1
3
2
1
4
1
4
1
2
2
1
"
3
4
1
1
1
0
0
WASHER
HANDWHEEL
KNOB
HEX
NUT
6
15
14
5
13
12
11
4
10
9
3
8
7
6
2
5
4
1
3
2
ut
1
Ind
I
Cut
"
1
3
1/8
3/32
2.5
2
1
4
8
1.5
1
Repeat 3
1
2
.5
0
1/16
1/32
0
0
4
1
4
1
0
1
2
1
"
3
1
1
4
HEX KEY
SCREW
Fig. 6
Fig. 8
12
Download from Www.Somanuals.com. All Manuals Search And Download.
ASSEMBLY
MOUNTING PLANER TO WORKBENCH
If your planer is to be used in a permanent location, it is
recommended you secure it to a workbench or other stable
surface. When mounting the planer to a workbench, holes
should be drilled through the supporting surface of the
workbench.
6
15
14
13
12
11
10
9
5
ꢀ Mark holes on workbench where planer is to be mounted
4
3
8
7
using holes in planer base as a template for hole pattern.
6
2
5
Ind
I
Cut
4
3
2.5
1/8
3/32
2
1
1.5
3
1
.5
ut
0
1/16
1/32
2
1"
1
ꢀ Drill four holes through workbench.
1
Repeat3
0
1
2
8
0
4
0
1
1
4
1
1
"
3
4
4
1
2
1
ꢀ Place planer on workbench aligning holes in the planer
base with holes drilled in the workbench.
ꢀ Insert four bolts (not included) and tighten securely with
lock washers and hex nuts (not included).
NOTE: All bolts should be inserted from the top. Install
the lock washers and hex nuts from the underside of the
workbench.
Supporting surface where planer is mounted should be
examinedcarefullyaftermountingtoinsurethatnomovement
during use can result. If any tipping or walking is noted,
secure workbench or support surface before beginning
planing operation.
Fig. 9
ꢀ From the back of the machine, locate the dust chute
knobs on the cutter head assembly. See Figure 10.
Turning counterclockwise, loosen each screw.
CLAMPING PLANER TO WORKBENCH
See Figure 9.
ꢀ Aligning the dust chute over the holes on the cutter head
assembly, replace the dust chute knobs by turning them
clockwise.
Iftheplaneristobeusedasaportabletool,itisrecommended
youfastenitpermanentlytoamountingboardthatcaneasily
be clamped to a workbench or other stable surface. The
mounting board should be of sufficient size to avoid tipping
while planer is in use. Any good grade plywood or chipboard
with a 3/4 in. (19 mm) thickness is recommended.
NOTE: To minimize sawdust accumulation on your
workpiece, attach either a 2-1/2 in. (64 mm) or 4 in.
(102 mm) shop vac hose to either the left or right end of
the dust chute.
ꢀ Mark holes on board where planer is to be mounted
using holes in planer base as a template for hole
pattern.
ꢀ Follow last three steps in section Mounting Planer to
DUST CHUTE
KNOBS
Workbench.
If lag bolts are used, make sure they are long enough to go
through holes in planer base and material the planer is being
mounted to. If machine bolts are used, make sure bolts are
long enough to go through holes in planer base, the material
being mounted to, and the lock washers and hex nuts.
INSTALLING THE DUST CHUTE
See Figure 10.
ꢀ Unplug your planer.
CUTTER
HEAD
GUARD
OUTFEED
TABLE
EXTENSION
WARNING:
Failure to turn the tool off, remove the switch key,
and unplug the tool before servicing or making ad-
justments could result in accidental starting causing
possible serious personal injury.
DUST
CHUTE
Fig. 10
13
Download from Www.Somanuals.com. All Manuals Search And Download.
ASSEMBLY
LEVELING THE TABLE EXTENSIONS
See Figure 11.
The infeed and outfeed table extensions are attached to the
planer. Shipped in a folded, "upright" position, the table
extensionsmustbeinthe"down"positionbeforeplaningcan
begin. For accurate planing, table extensions must be level
with the planer table.
6
15
14
13
12
11
10
9
TABLE
EXTENSION
5
4
3
8
7
6
2
5
4
1
3
STOP SCREWS
2
1
0
0
NOTE: For optimum performance, always check to make
sure the table extensions are level before beginning planing
operations.
To Level:
ꢀ Unplug your planer.
LOCK NUT
WARNING:
Failure to unplug the tool could result in accidental
starting causing possible serious personal injury.
STRAIGHT
EDGE
6
ꢀ Place a straight edge or level across both the planer
15
14
5
13
12
11
4
table and table extensions.
10
9
TABLE
EXTENSION
3
8
7
6
2
ꢀ If adjustment is necessary, lift table extensions and loosen
lock nuts. Adjust stop screws (one on each side) until
extension table is level with planer table.
5
4
Ind
I
Cut
3
2.5
2
1/8
3/32
1
3
1.5
1
ut
.5
0
2
1/16
1/32
1"
1
1
4
0
Repeat3
1
8
0
0
2
1
4
1
4
1
2
1
"
3
4
1
1
ꢀ Press down on the table extension to ensure the table
extension is properly seated.
ꢀ Tighten lock nuts securely when adjustments are
complete.
PLANER
TABLE
NOTE: Four screws attach table extensions to support
bars; loosening these screws may aid in leveling table
extensions.
Fig. 11
BLADE HEIGHT ADJUSTMENT
See Figure 12.
Raising and lowering the depth adjustment handwheel
controls the depth of cut on your planer.
NOTE: Never adjust blade height with cutter lock in the
"locked" position (pushed to the far right).
To Raise:
ꢀ Push cutter lock to the left to unlock cutter head
assembly.
ꢀ Turn the depth adjustment handwheel clockwise to the
desired height.
SURE-
CUT™
6
15
14
5
13
12
ꢀ Once the cutter head is in desired position, lock the
cutter head assembly in place by pushing the cutter lock
handle to the right.
11
4
10
9
3
8
7
6
2
5
4
To Lower:
ut
1
3
1
"
1
2
1
4
8
ꢀ Push cutter lock to the left to unlock cutter head
Repeat 3
DEPTH
ADJUSTMENT
HANDWHEEL
1
2
0
4
1
1
0
assembly.
ꢀ Turn the depth adjustment handwheel counterclockwise
to the desired height.
ꢀ Once cutter head assembly is in the desired position,
lock cutter head in place by pushing cutter lock handle to
the right.
NOTE: Each complete rotation of the handle moves the
cutter head assembly 1/64 in. (1.60 mm).
Fig. 12
Download from Www.Somanuals.co1m4. All Manuals Search And Download.
ASSEMBLY
THICKNESS SCALE ADJUSTMENT
THICKNESS
SCALE
6
5
4
3
2
1
0
15
14
13
12
11
10
9
See Figure 13.
Located on the right front of the planer, the thickness scale
shows the depth of the finished workpiece. Inaccurate cuts
can be prevented by routinely checking the alignment of the
thickness scale.
SCALE
INDICATOR
SCREWS
ꢀ Table extensions must be level with planer table.
ꢀ Plane a scrap piece of wood and measure the depth of
SCALE
INDICATOR
8
the finished piece.
7
ꢀ If properly adjusted, the depth of the finished piece should
6
be the same as indicated on the thickness scale.
5
ꢀ If out of adjustment, loosen the scale indicator screws
holding the scale indicator and adjust the thickness
indicator to the correct setting.
4
3
2
ꢀ Retighten screws securely.
1
0
REPEAT-A-CUT™
See Figure 14.
Fig. 13
Plane a scrap piece of wood and measure the depth of the
finished piece. If an adjustment is needed:
ꢀ Unplug your planer.
Cut
-
A
-
Repeat
4
WARNING:
2
Failure to turn the tool off, remove the switch key,
and unplug the tool could result in accidental start-
ing causing possible serious personal injury.
SET SCREW
REPLANE
INDICATOR
ꢀ Pull the replane indicator straight out to remove.
ꢀ Remove the set screw on the right-hand side of the
planer Repeat-A-Cut™ cover (see figure 14).
ꢀ Carefully lift and pull the Repeat-A-Cut™ cover off.
LOCK NUT
ꢀ Lower the cutter head assembly until it stops against the
stop screw.
ꢀ Using an accurate ruler or a scrap piece of wood, check
the measurement against the replane indicator setting.
ꢀ If adjustment is necessary, use a wrench to loosen the
lock nut and adjust the stop screw to the correct height.
ꢀ Once the adjustment is made, retighten the lock nut and
stop screw securely.
ꢀ Replace the Repeat-A-Cut™ cover and secure using the
set screw.
ꢀ Replace the replane indicator.
STOP SCREW
Fig. 14
APPLICATIONS
You may use the planer for the purposes listed below:
WARNING:
ꢀ Planing the surface of a piece of lumber.
The use of this planer on materials not listed may
damage the planer and may cause serious per-
sonal injury.
15
Download from Www.Somanuals.com. All Manuals Search And Download.
OPERATION
GETTING STARTED
Before turning on the planer, check for loose fasteners,
fittings, or hardware. Be sure the dust cover is securely
mounted and that the blade cutter rotates freely.
WARNING:
Do not force feed the workpiece through the ma-
chine. Let the planer apply the proper feed rate.
Lower the cutter head assembly to approximately 1 in.
(25 mm) above the planer table surface. Without putting any
loadontheplaner, testthemotorbyturningtheplaneronand
allowingittoreachfullspeed.Iftheplanersoundsexcessively
loud or has excessive vibration, turn off the machine
immediately and check again for any loose hardware,
retightening any you may find.
WARNING:
Always wear safety goggles or safety glasses with
side shields during power tool operation or when
blowing dust. If operation is dusty, also wear a dust
mask.
THICKNESS PLANING
Thickness planing sizes workpiece to desired thickness
whilecreatingasmooth, levelsurface. Thicknessofeachcut
will depend on type of wood (hardwood versus softwood),
width of workpiece, straightness, dryness, and grain
composition. Whenever working with a new type of wood,
makethintestcutsonascrappieceofwoodfirsttodetermine
potential problems with the workpiece.
Worn cutter blades will affect cutting accuracy. Planing with
dull or nicked cutter blades may produce ridges or rough
workpiece surfaces.
Gum and pitch on the cutter blades will cause them to wear
prematurely. Using a gum and pitch remover to keep your
cutter blades clean will prolong their wear.
Refer to the Maintenance Section of this operator's manual
for instructions on how to remove and replace or turn the
cutter blades.
PLANING
Thickness planers work best if at least one side of the
workpiecehasaflatsurface. Whenbothsidesofaworkpiece
is rough, use a surface planer or jointer first to define the
initial flat surface. Plane one side of the workpiece then flip
the workpiece and plane the surface of the reverse side.
NOTE: Cutter blades are double-edged and can be turned
once to the opposite, unused edge before replacement is
required. Cutter blades must ALWAYS be replaced as a set.
LOCKING THE SWITCH
See Figure 15.
Always plane both sides of a workpiece to reach the desired
thickness.Thiswillleavetheworkpiecewithuniformmoisture
to prevent warp during the drying process.
ꢀ Wait until the planer has come to a full and complete
stop.
When one end of the workpiece is thicker than the opposite
end by more than 1/8 in. (3 mm), make several cuts with the
planer starting with light planing cuts first. Remember, light
cuts create a finer finish than heavier cuts.
ꢀ Place the switch in the OFF position, remove the switch
key from the switch assembly. Store key in safe place.
ꢀ Do not plane a workpiece less than 3/16 in. (5 mm) thick.
ꢀ Do not plane a workpiece less than 3/4 in. (19 mm) wide.
SWITCH KEY
ꢀ Do not plane workpiece shorter than 14 in. (356 mm)
long as this will cause kickback.
ꢀ Do not plane more than one workpiece at a time.
RESET ON
PULL OUT TO LOCK
P
ꢀ Do not lower the cutter head assembly lower than 3/16
U
L
L
OFF
P
U
S
H
I
in. (5 mm)
O
Donotcontinuouslyusetheplanersetatthemaximumdepth
of cut (1/8 in., 3 mm) and at full width of cut (13 in., 330 mm).
Continuous use at maximum cutting capacity will damage
the motor.
ON
OFF
PULL OUT TO LOCK
WARNING:
PULL OUT TO LOCK
Never plane workpiece with loose knots or
foreign objects. Do not plane workpieces that are
severely bowed, twisted, or knotted. Cutter blades
can dull, chip, or break causing possible serious
personal injury.
RESET ON
RESET
P
U
L
L
L
L
OFF
OFF
I
I
P
U
S
H
P
U
S
H
O
O
Fig. 15
Download from Www.Somanuals.co1m6. All Manuals Search And Download.
OPERATION
DEPTH GAGE
See Figure 16.
Thedepthgageindicatestheamountofwoodbeingremoved
in a planing pass. The workpiece must be positioned under
the depth gage on the front of the planer.
Never make a planing cut deeper than:
DEPTH GAGE
ꢀ 1/8 in. (3 mm) for material up to 6 in. (152 mm) wide
ꢀ 1/16 in. (1.6 mm) for material 6 in. (152 mm) - 13 in.
(330 mm) wide
6
15
14
13
12
11
10
9
5
4
3
8
Do not continuously use the planer at the maximum depth of
cut,1/8 in. (3 mm), as it will damage the motor.
7
6
2
5
4
1
3
ut
1
Ind
I
2
"
1
Cut
3
1/8
3/32
1
4
2.5
2
8
Repeat 3
1
1.5
1
2
0
.5
0
4
1/16
1/32
0
1
4
1
0
1
2
1
"
3
1
1
4
REPLANING/USING REPEAT-A-CUT™
See Figure 17.
Your planer has a replane feature using preset markers for
repetitive planing. The Repeat-A-Cut™ allows you to plane
material at a set measurement of 1/4 in. (6 mm). The
maximum depth of the replane indicator is 1-3/4 in. (44 mm).
ꢀ Push Sure Cut™ to the left to unlock cutter head
assembly.
Fig. 16
ꢀ Raise cutter head assembly to a height greater than
1-3/4 in. (44 mm).
ꢀ Move the replane indicator to the desired height.
ꢀ Lower the cutter head assembly until it stops.
ꢀ Lock cutter head assembly in place by pushing the Sure
Cut™ to the right.
Avoid using severely warped wood as it can jam the planer.
If it must be used, rip it in half before planing to help minimize
the possibility of jamming. If jamming does occur, turn the
switch off and unplug the planer immediately. Raise the
cutter head assembly high enough to remove the workpiece
easily. Carefully check to make sure no damage to the tool
has occurred before making the next planing pass.
AVOIDING SNIPE
Snipes, or depressions made at either end of a workpiece by
cutter blades, can occur when the board is not properly
supported. Engaging the cutter lock before planing will
minimize snipe. Although snipe may be barely noticeable, it
is important to keep the workpiece parallel and flat with the
planer table to minimize snipe. Butting workpieces end-to-
end as they are fed through the planer will minimize the
problem, especially for shorter pieces, because it provides a
more stable feed.
Always feed the workpiece in the direction of the grain. This
allows the cutter blades to sever the wood fibers instead of
tearing them. Feeding against the grain can also cause the
cutter blades to chip the workpiece.
CUTTER HEAD
ASSEMBLY
For workpieces longer than 48 in. (122 cm), greater care
must be taken to reduce the problem because the additional
length means more of the total weight is unsupported by the
planer table and rollers causing the shifting weight to work
against keeping the stock flat.
To remove snipe from a finished workpiece, cut off the end
of the workpiece where snipe is noticeable.
6
15
14
5
13
12
11
4
10
9
3
8
7
WARPED WOOD
6
2
5
4
1
3
ut
Little or no warpage is the ideal condition for planing a
workpiece. Simply turn the workpiece over and plane it to the
desired thickness. Otherwise, plane the top flat first, turn the
workpiece and plane the bottom half.
Ind
I
2
"
1
Cut
3
1/8
3/32
1
4
2.5
2
1
8
Repeat 3
1
1.5
1
2
0
.5
0
4
1/16
1/32
0
1
4
1
0
1
2
1
"
3
1
1
4
Foraboardthatiscuppedorbowedacrossitswidth, thebest
method is to rip the board lengthwise down the middle and
planethepiecesseparately. Thismethodeliminatesmuchof
the waste in planing cupped or bowed workpieces.
REPLANE
INDICATOR
The only way to remove the bow from a workpiece that is
cupped or bowed down its length is to use a jointer.
Fig. 17
Download from Www.Somanuals.co1m7. All Manuals Search And Download.
MAINTENANCE
WARNING:
To avoid injury, never rotate the cutter block by
hand.
WARNING:
When servicing, use only identical replacement
parts. Use of any other part may create a hazard or
cause product damage.
ꢀ Using the notched end of the magnetic blade wrench,
remove the blade by hooking the notch over the end of
the blade and pulling straight out.
GENERAL
Avoid using solvents when cleaning plastic parts. Most
plastics are susceptible to damage from various types of
commercial solvents and may be damaged by their use. Use
clean cloths to remove dirt, carbon dust, etc.
WARNING:
To reduce the risk of injury, never perform the plan-
ing operation with the cutter head guard removed.
CAUTION:
Do not at any time let brake fluids, gasoline, petro-
leum-based products, penetrating oils, etc. come in
contact with plastic parts. They contain chemicals
that can damage, weaken or destroy plastic.
CUTTERHEAD
(SIDE VIEW)
CUTTER BLADE REPLACEMENT
See Figure 18.
Yourplanerisequippedwithreplaceable/disposabledouble-
edgedcutterbladesattachedtoarotatingcutterblock. Worn
cutter blades will affect cutting accuracy and may produce
ridges on the workpiece.
BLADE
MAGNETIC
BLADE WRENCH
SQUARE
HEAD BOLTS
To Replace:
CUTTER LOCK
ꢀ Unplug your planer.
BLADE
WARNING:
Failure to turn the tool off, remove the switch key,
and unplug the tool before servicing or making
adjustments could result in accidental starting caus-
ing possible serious personal injury.
ꢀ Remove the top of the housing cover by lifting it up.
SQUARE
HEAD
BOLTS
ꢀ Lower the cutter head assembly.
ꢀ From the back of the planer, remove the two dust chute
knobs holding the dust chute in place.
ꢀ Remove the dust chute and the cutter head guard.
NOTE: When cutter head guard is removed, the cutter
head lock will engage when the head is rotated. Do not
operate thickness planer without the dust chute in place
or your planer will be damaged.
ꢀ If necessary, rotate the cutter block until it locks.
NOTE: Rotating the cutter block is accomplished from
beneath the cutter head assembly. Using the planer
table as a mirror, touch the threaded spindle where it
attaches to the planer table. Carefully move your fingers
up until you touch the drive belt. Turn the drive belt with
your fingers until the cutter head locks in place (see
Figure 18).
DRIVE
BELT
Fig. 18
ꢀ Carefully loosen the square head bolts.
18
Download from Www.Somanuals.com. All Manuals Search And Download.
MAINTENANCE
ꢀ If you are changing to the second side of the blade,
rotate the blade “end for end” keeping the same flat side
down. This correctly positions the blade for reinstallation.
ꢀ Lightly oil new cutter blade.
ꢀ Push the installed blade in firmly. Check that the blade
edge is parallel to the cutter head slot.
ꢀ Securely retighten the square head bolts.
ꢀ To rotate the cutter head to the next blade, hold down on
the red cutter lock and rotate the cutter head 180° as
shown in figure 18.
ꢀ Release the cutter lock and continue to rotate the cutter
head until it locks in place. This correctly positions the
blade for removal.
ꢀ Repeat the above steps for the second blade.
ꢀ Tighten square head bolts securely.
ꢀ Replace the cutter head guard, dust chute, the square
BLADE
STORAGE
head bolts, and then the top of the housing.
Fig. 19
BLADE STORAGE
See figure 19.
CORD
STORAGE
For your convenience, an extra set of blades can be stored
under the outfeed table extension.
Dispose of used blades properly. Wrap blades in tape before
disposal to avoid accidental injury.
CORD STORAGE
See figure 20.
For convenience, your planer comes equipped with a cord
storage area. When not in use, the power cord should be
wrapped around the left-hand side of the planer.
CAUTION:
Check extension cords before each use. If dam-
aged, replace immediately. Never use tool with a
damaged cord since touching the damaged area
could cause electrical shock resulting in serious
injury.
WARNING:
Fig. 20
Always wear safety goggles or safety glasses with
side shields during power tool operation or when
blowing dust. If operation is dusty, also wear a dust
mask.
WARNING:
To ensure safety and reliability, all repairs should
be performed by a qualified service technician at a
Authorized Service Center to avoid risk of personal
injury.
19
Download from Www.Somanuals.com. All Manuals Search And Download.
MAINTENANCE
GENERAL MAINTENANCE
WARNING:
Always begin by disconnecting the power supply.
6
15
14
13
12
11
10
9
BRUSH
ꢀ Periodically check all clamps, nuts, bolts, and screws for
tightness and condition. Make sure the throat plate is in
good condition and in position.
5
4
3
8
7
6
2
BRUSH CAP
5
4
t
1
1
3
ꢀ Stop the machine and recheck the cutter head gib screws
Ind
I
Cut
3
"
1
1/8
3/32
2
1
4
8
Repeat 3
1
2
.5
0
1/16
1/32
0
0
1
4
1
4
1
2
0
1
"
3
1
and blades for tightness after about 50 hours of operation.
1
4
ꢀ Clean plastic parts only with a soft damp cloth. DO
NOT use any aerosol or petroleum solvents.
LUBRICATION
Periodically, check all moving parts (spindle, roller surfaces,
handles, etc.) to ensure they are clean and well lubricated.
A light film of oil wiped on the face of the cutter blades will
keep them rust-free. All of the bearings in this tool are
lubricated with a sufficient amount of high grade lubricant for
the life of the unit under normal operating conditions. No
further lubrication is required.
Fig. 21
CLEANING
Sawdustbuildupandotherdebriscancausethetooltoplane
inaccurately. Periodic cleaning and waxing is needed for
accurate, precision planing.
MOTOR/ELECTRICAL
The universal motor is easy to maintain but must be kept
clean. Do not allow water, oil or sawdust to accumulate on or
in it. The sealed bearings are permanently lubricated and
need no further attention.
Do not allow sawdust to accumulate on the planer. Clean the
dust chute after each use. Moving parts should be cleaned
regularly with penetrating oil and lubricated with a light
coating of medium-weight machine oil.
BRUSH REPLACEMENT
Paste wax should be applied to the planing table surface to
ease the movement of workpieces across it. Paste wax can
also be used on infeed and outfeed support surfaces but be
careful not to use so much that it will be absorbed into the
wood and interfere with staining.
See Figure 21.
Your planer has externally accessible brush assemblies that
should be checked every 10 to 15 operating hours for wear.
To inspect or replace these brushes, unscrew the brush cap
located at the right front and left rear of the planer. Be sure
to replace the brush cap securely after inspection or repairs.
Check feed rollers after each use for resin buildup because
they must be clean to be effective. If buildup occurs, use a
mild, nonflammable tar and pitch remover.
20
Download from Www.Somanuals.com. All Manuals Search And Download.
TROUBLESHOOTING
PROBLEM
CAUSE
SOLUTION
1. Replace, turn or sharpen cutter blades
1. Dull cutter blades
Snipe (depressions at ends
of workpiece)
2. Butt pieces end-to-end as they are fed
into planer
2. Incorrect butted stock
3. Securely tighten mounting hardware
4. Lock cutter head
3. Unit not securely mounted
4. Cutter head not locked
1. Too deep a blade setting
Torn grain
1. Reduce depth of cut
2. Feed other end of board first
2. Workpiece being fed against
grain
3. Replace, turn or sharpen cutter blades
1. Dry wood before planing
3. Dull cutter blades
1. High wood moisture content
2. Dull cutter blades
Fuzzy/Rough grain
2. Replace, turn or sharpen cutter blades
3. Reduce depth of cut
3. Too deep a blade setting
4. Incorrect feeding speed
4. Check for adequate power supply,
check cord and plug for damage,
check condition of motor brushes
1. Adjust elevation screws
1. Cutter head assembly not level
with planer surface
Uneven depth of cut
2. Have service performed by an
Authorized Service Center
2. Unstable roller spring pressure
3. Feed roller worn unevenly
3. Have service performed by an
Authorized Service Center
Board thickness does not match
depth scale indicator
1. Adjust depth scale
1. Depth scale incorrectly set
2. Dirty planing table
1. Dirty spindle
2. Clean and wax planing table
1. Clean and lubricate
Cutter head height difficult to
adjust
2. Have service performed by an
Authorized Service Center
2. Worn chain
Will not start
1. Not plugged in
1. Check power source
2. No power at outlet
2. Replace fuse, reset breaker or call
Electrician
3. Have service performed by an
Authorized Service Center
3. Motor failure
4. Loose wire
4. Have service performed by an
Authorized Service Center
5. ON/OFF Switch malfunction
5. Have service performed by an
Authorized Service Center
Interrupted operation
1. Reduce load
1. Unit overloaded
2. Operate on circuit separate from other
appliances or motors or connect to
circuit with adequate amp rating
2. Circuit overloaded
21
Download from Www.Somanuals.com. All Manuals Search And Download.
WARRANTY
RIDGID® HAND HELD AND STATIONARY POWER TOOL
LIMITED THREE YEAR WARRANTY AND 90-DAY SATISFACTION GUARANTEE POLICY
This product is manufactured by One World Technologies,
WHAT IS NOT COVERED
Inc., under a trademark license from Ridgid, Inc. All warranty
This warranty applies only to the original purchaser at retail
communications should be directed to One World
and may not be transferred. This warranty only covers
Technologies, Inc., attn: RIDGID handheld and stationary
defects arising under normal usage and does not cover any
power tool technical service at (toll free) 1-866-539-1710.
malfunction, failure or defect resulting from misuse, abuse,
90-DAY SATISFACTION GUARANTEE POLICY
neglect, alteration, modification or repair by other than an
authorized service center for RIDGID branded hand held
and stationary power tools. RIDGID, INC. AND ONE
WORLD TECHNOLOGIES, INC. MAKE NO
WARRANTIES, REPRESENTATIONS OR PROMISES AS
TO THE QUALITY OR PERFORMANCE OF ITS POWER
TOOLS OTHER THAN THOSE SPECIFICALLY STATED
IN THIS WARRANTY.
During the first 90 days after the date of purchase, if you are
dissatisfied with the performance of this RIDGID tool for any
reason you may return the tool to the dealer from which it
was purchased for a full refund or exchange. To receive a
replacement tool you must present proof of purchase and
return all original equipment packaged with the original
product. The replacement tool will be covered by the limited
warranty for the balance of the three year warranty period.
ADDITIONAL LIMITATIONS
WHAT IS COVERED UNDER THE LIMITED
THREE YEAR WARRANTY
This warranty covers all defects in workmanship or materials
in this RIDGID tool for the three year period from the date of
purchase. This warranty is specific to this tool. Warranties
for other RIDGID products may vary.
To the extent permitted by applicable law, all implied
warranties, including warranties of MERCHANTABILITY or
FITNESS FORAPARTICULAR PURPOSE, are disclaimed.
Any implied warranties, including warranties of
merchantability or fitness for a particular purpose, that cannot
be disclaimed under state law are limited to three years from
the date of purchase. One World Technologies, Inc. is not
responsible for direct, indirect, incidental or consequential
damages. Some states do not allow limitations on how long
an implied warranty lasts and/or do not allow the exclusion
or limitation of incidental or consequential damages, so the
above limitations may not apply to you. This warranty gives
you specific legal rights, and you may also have other rights
which vary from state to state.
HOW TO OBTAIN SERVICE
To obtain service for this RIDGID tool you must return it,
freight prepaid, to an authorized RIDGID service center for
hand held and stationary power tools. You may obtain the
location of the authorized service center nearest you by
calling (toll free) 1-866-539-1710 or by logging on to the
warranty service, you must present the proof of purchase
documentation, which includes a date of purchase. The
authorized service center will repair any faulty workmanship,
and either repair or replace any defective part, at our option
at no charge to you.
One World Technologies, Inc.
Hwy. 8
Pickens, SC 29671
22
Download from Www.Somanuals.com. All Manuals Search And Download.
NOTES
Download from Www.Somanuals2.c3om. All Manuals Search And Download.
OPERATOR'S MANUAL
13 in. THICKNESS PLANER
TP1300LS
CUSTOMER SERVICE INFORMATION
Forpartsorservice, contactyournearestRidgidauthorizedservicecenter. Besure
to provide all relevant information when you call or visit. For the location of the
authorized service center nearest you, please call 1-866-539-1710 or visit us
The model number of this tool is found on a plate attached to the center of the tool
base. Please record the serial number in the space provided below. When ordering
repair parts, always give the following information:
TP1300LS
TP13002
Stock No.
Model No.
Serial No.
983000-316
4 -30-04
Download from Www.Somanuals.com. All Manuals Search And Download.
|