OPERATOR’S MANUAL
18 VOLT/24 VOLT
MaxSelect™ HAND PLANER
WITH SPIRAL CUT
R888
NEW LITHIUM-ION BATTERY PACKS
MUST BE CHARGED BEFORE FIRST USE
BATTERIES AND CHARGERS SOLD
SEPARATELY
Your hand planer has been engineered and manufactured to our high standards for dependability, ease of operation, and
operator safety. When properly cared for, it will give you years of rugged, trouble-free performance.
WARNING:
To reduce the risk of injury, the user must read and understand the operator’s manual before using this product.
Thank you for buying a RIDGID product.
SAVE THIS MANUAL FOR FUTURE REFERENCE
1
Download from Www.Somanuals.com. All Manuals Search And Download.
GENERAL SAFETY RULES
Use safety equipment. Always wear eye protection.
Safety equipment such as dust mask, non-skid safety
shoes, hard hat, or hearing protection used for appropriate
conditions will reduce personal injuries.
Avoid accidental starting. Ensure the switch is in the
off-position before plugging in. Carrying power tools
with your finger on the switch or plugging in power tools
that have the switch on invites accidents.
WARNING!
Read all instructions. Failure to follow all
instructions listed below may result in electric
shock, fire and/or serious injury. The term “power
tool” in all of the warnings listed below refers
to your mains-operated (corded) power tool or
battery-operated (cordless) power tool.
Remove any adjusting key or wrench before turning
the power tool on. A wrench or a key left attached to
a rotating part of the power tool may result in personal
injury.
SAVE THESE INSTRUCTIONS
WORK AREA SAFETY
Keep work area clean and well lit. Cluttered or dark
Do not overreach. Keep proper footing and balance
at all times. This enables better control of the power tool
in unexpected situations.
Dress properly. Do not wear loose clothing or jewelry.
Keep your hair, clothing and gloves away from moving
parts. Loose clothes, jewelry or long hair can be caught
in moving parts.
If devices are provided for the connection of dust
extraction and collection facilities, ensure these are
connected and properly used. Use of these devices can
reduce dust-related hazards.
Do not wear loose clothing or jewelry. Contain long
hair. Loose clothes, jewelry, or long hair can be drawn
into air vents.
areas invite accidents.
Do not operate power tools in explosive atmospheres,
such as in the presence of flammable liquids, gases
or dust. Power tools create sparks which may ignite the
dust or fumes.
Keep children and bystanders away while operating a
power tool. Distractions can cause you to lose control.
ELECTRICAL SAFETY
Power tool plugs must match the outlet. Never modify
the plug in any way. Do not use any adapter plugs with
earthed (grounded) power tools. Unmodified plugs and
matching outlets will reduce risk of electric shock.
Avoid body contact with earthed or grounded surfaces
such as pipes, radiators, ranges and refrigerators.
There is an increased risk of electric shock if your body
is earthed or grounded.
Do not use on a ladder or unstable support. Stable
footing on a solid surface enables better control of the
power tool in unexpected situations.
Do not expose power tools to rain or wet conditions.
Water entering a power tool will increase the risk of
electric shock.
POWER TOOL USE AND CARE
Do not force the power tool. Use the correct power tool
for your application. The correct power tool will do the job
better and safer at the rate for which it was designed.
Do not abuse the cord. Never use the cord for carrying,
pulling or unplugging the power tool. Keep cord away
from heat, oil, sharp edges or moving parts. Damaged
or entangled cords increase the risk of electric shock.
Do not use the power tool if the switch does not turn
it on and off. Any power tool that cannot be controlled
with the switch is dangerous and must be repaired.
When operating a power tool outdoors, use an Disconnect the plug from the power source and/or
extension cord suitable for outdoor use. Use of a
cord suitable for outdoor use reduces the risk of electric
shock.
the battery pack from the power tool before making
any adjustments, changing accessories, or storing
power tools. Such preventive safety measures reduce
the risk of starting the power tool accidentally.
Use battery only with charger listed.
Store idle power tools out of the reach of children and
do not allow persons unfamiliar with the power tool
or these instructions to operate the power tool. Power
tools are dangerous in the hands of untrained users.
Maintain power tools. Check for misalignment or
binding of moving parts, breakage of parts and any
other condition that may affect the power tool’s
operation. If damaged, have the power tool repaired
before use. Many accidents are caused by poorly
maintained power tools.
MODEL
R888
BATTERY PACK
(18V) 130254007
CHARGER
(18V) 140276003
or 140276004
(24V) 130377001
(24V) 140315001
(R85008)
(R85009)
PERSONAL SAFETY
Stay alert, watch what you are doing and use common
sense when operating a power tool. Do not use a
power tool while you are tired or under the influence of
drugs, alcohol or medication. A moment of inattention
while operating power tools may result in serious personal
injury.
Keep cutting tools sharp and clean. Properly maintained
cutting tools with sharp cutting edges are less likely to
bind and are easier to control.
3
Download from Www.Somanuals.com. All Manuals Search And Download.
GENERAL SAFETY RULES
connection from one terminal to another. Shorting the
battery terminals together may cause burns or a fire.
Use the power tool, accessories and tool bits etc., in
accordance with these instructions and in the manner
intended for the particular type of power tool, taking
into account the working conditions and the work
to be performed. Use of the power tool for operations
different from those intended could result in a hazardous
situation.
Under abusive conditions, liquid may be ejected from
the battery, avoid contact. If contact accidentally
occurs, flush with water. If liquid contacts eyes,
additionally seek medical help. Liquid ejected from the
battery may cause irritation or burns.
BATTERY TOOL USE AND CARE
SERVICE
Ensure the switch is in the off position before inserting
battery pack. Inserting the battery pack into power tools
that have the switch on invites accidents.
Have your power tool serviced by a qualified repair
person using only identical replacement parts. This will
ensure that the safety of the power tool is maintained.
Recharge only with the charger specified by the
manufacturer. A charger that is suitable for one type
of battery pack may create a risk of fire when used with
another battery pack.
Use power tools only with specifically designated
battery packs. Use of any other battery packs may create
a risk of injury and fire.
When battery pack is not in use, keep it away from
other metal objects like paper clips, coins, keys, nails,
screws, or other small metal objects that can make a
WARNING!
To reduce the risk of injury, user must read
instruction manual.
When servicing a power tool, use only identical
replacement parts. Follow instructions in the
Maintenancesectionofthismanual.Useofunauthorized
parts or failure to follow Maintenance instructions may
create a risk of shock or injury.
SPECIFIC SAFETY RULES
Wait for the cutter to stop before setting the tool down.
An exposed cutter may engage the surface leading to
possible loss of control and serious injury.
Do not place battery tools or their batteries near fire
or heat. This will reduce the risk of explosion and possibly
injury.
Do not crush, drop or damage battery pack. Do not
use a battery pack or charger that has been dropped
or received a sharp blow. A damaged battery is subject
to explosion. Properly dispose of a dropped or damaged
battery immediately.
Batteries vent hydrogen gas and can explode in the
presence of a source of ignition, such as a pilot light.
To reduce the risk of serious personal injury, never use
any cordless product in the presence of open flame. An
exploded battery can propel debris and chemicals. If
exposed, flush with water immediately.
Do not charge battery tool in a damp or wet location.
Following this rule will reduce the risk of electric shock.
For best results, your battery tool should be charged
in a location where the temperature is more than
50°F but less than 100°F. To reduce the risk of serious
personal injury, do not store outside or in vehicles.
Under extreme usage or temperature conditions,
battery leakage may occur. If liquid comes in contact
with your skin, wash immediately with soap and water,
then neutralize with lemon juice or vinegar. If liquid
gets into your eyes, flush them with clean water for
at least 10 minutes, then seek immediate medical
attention. Following this rule will reduce the risk of serious
personal injury.
Use clamps or another practical way to secure and
support the workpiece to a stable platform. Holding
the work by hand or against your body leaves it unstable
and may lead to loss of control.
Hold power tools by insulated gripping surfaces when
performing an operation where the cutting tool may
contact hidden wiring or its own cord. Contact with a
“live” wire will also make exposed metal parts of the tool
“live” and shock the operator.
Know your power tool. Read operator’s manual
carefully. Learn its applications and limitations, as well
as the specific potential hazards related to this tool.
Following this rule will reduce the risk of electric shock,
fire, or serious injury.
Always wear safety glasses with side shields. Everyday
glasses have only impact resistant lenses. They are NOT
safety glasses. Following this rule will reduce the risk of
eye injury.
Protect your lungs. Wear a face or dust mask if the
operation is dusty. Following this rule will reduce the risk
of serious personal injury.
Protect your hearing. Wear hearing protection during
extended periods of operation. Following this rule will
reduce the risk of serious personal injury.
Battery tools do not have to be plugged into an
electrical outlet; therefore, they are always in
operating condition. Be aware of possible hazards
when not using your battery tool or when changing
accessories. Following this rule will reduce the risk of
electric shock, fire, or serious personal injury.
Ifthepowersupplycordisdamaged,itmustbereplaced
only by the manufacturer or by an authorized service
center to avoid risk.
4
Download from Www.Somanuals.com. All Manuals Search And Download.
SAFETY RULES FOR CHARGER
Do not let gasoline, oils, petroleum-based products,
etc. come in contact with plastic parts. They contain
chemicals that can damage, weaken, or destroy
plastic.
An extension cord should not be used unless
absolutely necessary. Use of improper extension cord
could result in a risk of fire and electric shock. If extension
cord must be used, make sure:
WARNING!
READ AND UNDERSTAND ALL INSTRUCTIONS.
Failure to follow all instructions listed below, may
result in electric shock, fire and/or serious personal
injury.
Before using battery charger, read all instructions and
cautionary markings in this manual, on battery charger,
battery, and product using battery to prevent misuse of
the products and possible injury or damage.
a. That pins on plug of extension cord are the same
number, size and shape as those of plug on charger.
b. That extension cord is properly wired and in
good electrical condition; and
c. That wire size is large enough for AC ampere
rating of charger as specified below:
CAUTION:
To reduce the risk of electric shock or damage
to the charger and battery, charge only lithium-
ion or nickel-cadmium rechargeable batteries as
specifically designated on your charger. Other
types of batteries may burst, causing personal
injury or damage.
Cord Length (Feet)
Cord Size (AWG)
25'
16
50'
16
100'
16
NOTE: AWG = American Wire Gauge
Do not operate charger with a damaged cord or
plug, which could cause shorting and electric shock. If
damaged, have the charger replaced by an authorized
serviceman.
Do not use charger outdoors or expose to wet or damp
conditions. Water entering charger will increase the risk
of electric shock.
Use of an attachment not recommended or sold by the
battery charger manufacturer may result in a risk of
fire, electric shock, or injury to persons. Following this
rule will reduce the risk of electric shock, fire, or serious
personal injury.
Do not abuse cord or charger. Never use the cord to
carry the charger. Do not pull the charger cord rather than
the plug when disconnecting from receptacle. Damage
to the cord or charger could occur and create an electric
shock hazard. Replace damaged cords immediately.
Make sure cord is located so that it will not be stepped
on, tripped over, come in contact with sharp edges
or moving parts or otherwise subjected to damage or
stress. This will reduce the risk of accidental falls, which
could cause injury, and damage to the cord, which could
result in electric shock.
Do not operate charger if it has received a sharp blow,
been dropped, or otherwise damaged in any way.
Take it to an authorized serviceman for electrical check
to determine if the charger is in good working order.
Do not disassemble charger. Take it to an authorized
serviceman when service or repair is required. Incorrect
reassembly may result in a risk of electric shock or fire.
Unplug charger from outlet before attempting any
maintenance or cleaning to reduce the risk of electric
shock.
Disconnect charger from the power supply when
not in use. This will reduce the risk of electric shock or
damage to the charger if metal items should fall into the
opening. It also will help prevent damage to the charger
during a power surge.
Risk of electric shock. Do not touch uninsulated portion
of output connector or uninsulated battery terminal.
Save these instructions. Refer to them frequently and
use them to instruct others who may use this tool. If you
loan someone this tool, loan them these instructions also
to prevent misuse of the product and possible injury.
Keep cord and charger from heat to prevent damage
to housing or internal parts.
IMPORTANT SAFETY INSTRUCTIONS
1. SAVE THESE INSTRUCTIONS
This manual contains important safety and operating instructions for battery chargers (24V) 140315001 (R85009) and
(18V) 140276003 or 140276004.
2. Before using battery charger, read all instructions and cautionary markings on battery charger, battery, and product
using battery.
3. CAUTION: To reduce the risk of injury, charge only RIDGID lithium-ion batteries on the RIDGID lithium ion charger
and RIDGID nickel-cadmium batteries on RIDGID nickel-cadmium chargers. These batteries and chargers are not
interchangeable. Other types of batteries may burst, causing personal injury or damage.
5
Download from Www.Somanuals.com. All Manuals Search And Download.
SYMBOLS
Some of the following symbols may be used on this tool. Please study them and learn their meaning. Proper interpretation
of these symbols will allow you to operate the tool better and safer.
SYMBOL
NAME
DESIGNATION/EXPLANATION
V
Volts
Voltage
Current
A
Hz
W
Amperes
Hertz
Frequency (cycles per second)
Power
Watt
min
Minutes
Time
Alternating Current
Direct Current
No Load Speed
Class II Tool
Type of current
Type or a characteristic of current
Rotational speed, at no load
Double-insulated construction
Revolutions, strokes, surface speed, orbits etc., per minute
n
o
.../min
Per Minute
Wet Conditions Alert
Do not expose to rain or use in damp locations.
To reduce the risk of injury, user must read and understand
operator’s manual before using this product.
Read The Operator’s Manual
Always wear safety goggles or safety glasses with side shields and,
as necessary, a full face shield when operating this product.
Eye Protection
Safety Alert
Precautions that involve your safety.
Failure to keep your hands away from the blade will result in serious
personal injury.
No Hands Symbol
Failure to keep your hands away from the blade will result in serious
personal injury.
No Hands Symbol
No Hands Symbol
No Hands Symbol
Failure to keep your hands away from the blade will result in serious
personal injury.
Failure to keep your hands away from the blade will result in serious
personal injury.
To reduce the risk of injury or damage, avoid contact with any hot
surface.
Hot Surface
6
Download from Www.Somanuals.com. All Manuals Search And Download.
SYMBOLS
The following signal words and meanings are intended to explain the levels of risk associated with this product.
SYMBOL
SIGNAL
MEANING
Indicates an imminently hazardous situation, which, if not avoided, will result
in death or serious injury.
DANGER:
Indicates a potentially hazardous situation, which, if not avoided, could result
in death or serious injury.
WARNING:
CAUTION:
CAUTION:
Indicates a potentially hazardous situation, which, if not avoided, may result in
minor or moderate injury.
(Without Safety Alert Symbol) Indicates a situation that may result in property
damage.
SERVICE
WARNING:
Servicing requires extreme care and knowledge and should
be performed only by a qualified service technician. For
service we suggest you return the product to your nearest
AUTHORIZED SERVICE CENTER for repair. When servic-
ing, use only identical replacement parts.
To avoid serious personal injury, do not attempt
to use this product until you read thoroughly and
understand completely the operator’s manual.
If you do not understand the warnings and
instructions in the operator’s manual, do not use
this product. Call RIDGID customer service for
assistance.
WARNING:
The operation of any power tool can result in foreign objects being thrown into your eyes, which can result
in severe eye damage. Before beginning power tool operation, always wear safety goggles or safety glasses
with side shields and, when needed, a full face shield. We recommend Wide Vision Safety Mask for use
over eyeglasses or standard safety glasses with side shields. Always use eye protection which is marked
to comply with ANSI Z87.1.
SAVE THESE INSTRUCTIONS
7
Download from Www.Somanuals.com. All Manuals Search And Download.
FEATURES
PRODUCT SPECIFICATIONS
Planing Depth..........................................................1/16 in.
Setting Increment....................................................1/64 in.
Rabbet Depth.........................................................0-1/2 in.
Charger Input ................................... 120 V, 60 Hz, AC only
Switch ........................................................... Single Speed
No Load Speed
18V Nickel-Cadmium Battery Pack.....11,000 r/min. (RPM)
24V Lithium-Ion Battery Pack..............13,000 r/min. (RPM)
Planing Width.........................................................3-1/4 in.
LOCK-OFF BUTTON
SWITCH
TRIGGER
DUST BAG
BLADE WRENCH
CHIP EXHAUST
DEPTH
ADJUSTMENT
KNOB
EDGE GUIDE/
RABBET GUIDE
AUTOMATIC
REAR STAND
Fig. 1
8
Download from Www.Somanuals.com. All Manuals Search And Download.
FEATURES
KNOW YOUR HAND PLANER
EDGE GUIDE/RABBET GUIDE
The edge guide may be attached for planing edges and
making rabbet cuts.
See Figure 1.
The safe use of this product requires an understanding of
the information on the tool and in this operator’s manual as
well as a knowledge of the project you are attempting. Before
use of this product, familiarize yourself with all operating
features and safety rules.
AUTOMATIC REAR STAND
The automatic rear stand allows the planer to sit on a
workpiece or table without damaging the workpiece or the
blades.
CHIP EXHAUST
LOCK-OFF BUTTON
The dust bag attaches to the chip exhaust of the planer to
keep the work area free of debris. A 1-1/4 in. vacuum hose
can also be attached for chip collection.
The lock-off button locks the switch trigger in the OFF
position when the switch is released.
SPIRAL CUT BLADE
The blade is attached to a cylinder-shaped blade holder for
spiral cut action that creates a smooth finish.
DEPTH ADJUSTMENT KNOB
The depth adjustment knob selects 0-1/16 in. planing
depths, in increments of 1/64 in.
9
Download from Www.Somanuals.com. All Manuals Search And Download.
ASSEMBLY
NOTE: For secure installation of the dust bag, align the slot
on the neck of the dust bag with the alignment tab on the
bottom of the chip exhaust.
UNPACKING
This product has been shipped completely assembled.
Carefully remove the tool and any accessories from the
box. Make sure that all items listed in the packing list are
included.
ATTACHING THE PLANER TO A VACUUM
See Figure 3.
Inspect the tool carefully to make sure no breakage or
The chip collection system of the hand planer has a 1-1/4 in.
port for inserting a vacuum hose.
damage occurred during shipping.
Do not discard the packing material until you have care-
Remove the dust bag.
fully inspected and satisfactorily operated the tool.
Attach a vacuum hose to the chip exhaust.
If any parts are damaged or missing, please call
Connect the vacuum to a power supply.
1-866-539-1710 for assistance.
PACKING LIST
18V/24V Hand Planer
Edge Guide/Rabbet Guide
Blade Wrench
WARNING:
When the tool is not connected to a vacuum,
always reinstall the dust bag back onto the tool.
Failure to do so could cause dust or foreign objects
to be thrown into your face or eyes, which could
result in possible serious injury.
Dust Bag
Operator’s Manual
WARNING:
CHIP EXHAUST
If any parts are damaged or missing do not operate
this tool until the parts are replaced. Failure to
heed this warning could result in serious personal
injury.
WARNING:
Do not attempt to modify this tool or create
accessories not recommended for use with this
tool. Any such alteration or modification is misuse
and could result in a hazardous condition leading
to possible serious personal injury.
DUST BAG
Fig. 2
WARNING:
To prevent accidental starting that could cause
serious personal injury, always remove the battery
CHIP EXHAUST
pack from the tool when assembling parts.
INSTALLING/REMOVING THE DUST BAG
See Figure 2.
The dust bag located on the right side of the hand planer
provides a dust collection system. Wood particles are drawn
up through the base and collect in the dust bag during op-
eration. For more efficient operation, empty the dust bag
when half full.
VACUUM HOSE
Fig. 3
To install, slide the dust bag adaptor onto the dust port on
the planer. To remove the dust bag, grasp the adaptor and
pull the dust bag away from the planer.
10
Download from Www.Somanuals.com. All Manuals Search And Download.
OPERATION
THE FOLLOWING INSTRUCTIONS ARE
FOR RIDGID 24V LITHIUM-ION BATTERY
PACKS AND THE 24V RIDGID LITHIUM-ION
CHARGER.
WARNING:
Do not allow familiarity with tools to make you
careless. Remember that a careless fraction of a
second is sufficient to inflict severe injury.
CHARGING THE BATTERY PACK
NOTE: New 24 Volt lithium-ion battery packs will not
work without first being charged. Before first time use,
charge the battery pack to activate it.
WARNING:
Always wear safety goggles or safety glasses with
side shields when operating tools. Failure to do so
could result in objects being thrown into your eyes
resulting in possible serious injury.
It is not necessary to drain the battery pack completely
before recharging. Lithium-ion battery packs have no
“memory” and can be recharged at any time. It is therefore
possible to charge the battery pack before extended usage
even if the battery pack is not completely drained of charge.
Use the charge level indicator to determine the amount of
charge in the battery pack.
WARNING:
Do not use any attachments or accessories
not recommended by the manufacturer of this
tool. The use of attachments or accessories not
recommended can result in serious personal
injury.
Lithium-ion batteries deliver fade free power for their entire
run time. 24 Volt lithium-ion tools will not gradually lose
power due to decreasing battery charge. Instead, power from
the battery pack will drop from full to zero once the full charge
has been drained from the battery. Once this happens, the
tool’s power drops from full to zero, and recharging of the
battery is required
APPLICATIONS
You may use this tool for the purposes listed below:
CHARGE
LEVEL INDICATOR
Planing the surface of a piece of lumber
Planing the edge of a piece of lumber
Making rabbet cuts in a piece of lumber
24vXLi
CAUTION:
?
If at any point during the charging process none
of the LEDs are lit, remove the battery pack from
the charger to avoid damaging the product. DO
NOT insert another battery. Return the charger and
battery to your nearest service center for service
or replacement.
CAUTION:
Charge in a well ventilated area. Do not block
charger vents. Keep them clear to allow proper
ventilation.
NOTE: Charge only RIDGID lithium-ion batteries on the
RIDGID lithium-ion charger and RIDGID nickel-cadmium
batteries on RIDGID nickel-cadmium chargers. These
batteries and chargers are not interchangeable.
Refer to the General Safety Rules for compatibility.
Fig. 4
11
Download from Www.Somanuals.com. All Manuals Search And Download.
OPERATION
FULL
3/4
TO CHARGE
CAPACITY
CAPACITY
A fully discharged battery pack with a temperature between
32°F (0°C) and 150°F (65°C) will charge in about an hour.
Charge the 24 Volt lithium-ion battery pack only with the
charger provided.
1/2
CAPACITY
Connect the charger to a power supply.
NOTE: If needed, the charger can operate with most
generators and inverters rated at 300 Watts or higher.
Attach the battery pack to the charger by aligning the
raised ribs on the battery pack with the grooves in the
charger, then slide the battery pack onto the charger. See
Figure 4.
Do not place the charger in an area of extreme heat or
cold. It will work best at normal room temperature.
After charging is complete, the continuous green light
will come on and the charge level indicator lights on the
battery will go off.
24vXL
i
?
CHARGE
LEVEL
INDICATOR
BUTTON
1/4
CHARGE
LEVEL INDICATOR
CAPACITY
Fig. 5
The charger will keep the battery pack fully charged if left
on the charger.
GREEN LED
RED LED
CHARGING
INDICATOR
CHARGE LEVEL INDICATOR
See Figure 5.
The charge level indicator shows that the battery is charged
at 1/4, 1/2, 3/4, or full capacity. To display the amount of
charge left in the battery, press and hold the charge level
indicator button.
FULL
INDICATOR
EVALUATE
INDICATOR
NOTE: When the battery pack contains less than 10%
charge, the 1/4 charge level indicator will flash.
CHARGING A HOT BATTERY PACK
If the battery pack is above normal temperature range, the
red LED will begin flashing and the green LED will be off.
When the battery pack cools down to approximately 150°F
(65°C), the charger will automatically begin fast charge mode.
DEFECTIVE
INDICATOR
NOTE: Refer to CHARGING THE BATTERY PACK for
normal recharging of batteries. If the charger does not charge
the battery pack under normal circumstances, return both
the battery pack and charger to your nearest repair center
for electrical check. For the location of your nearest repair
center, please call 1-866-539-1710.
Fig. 6
CHARGING A COOL BATTERY PACK
If the battery pack is below normal temperature range, the
red LED will begin flashing and the green LED will be off.
When the battery warms to a temperature of more than 14°F
(-10°C), the charger will automatically begin charge mode.
COLD WEATHER OPERATION
The lithium-ion battery pack can be used in temperatures
down to -4°F. When the battery pack is very cold, it may
“buzz” for the first minute of use to warm itself up. Put
the battery pack on a tool and use the tool in a light duty
application. After about a minute, the pack will have warmed
itself up and begin operating normally.
12
Download from Www.Somanuals.com. All Manuals Search And Download.
OPERATION
LED FUNCTION OF RIDGID 24V LITHIUM-ION CHARGER
See Figure 6.
LED
INDICATOR
BATTERY
PACK
RED
LED
GREEN
LED
ACTION
Charging Fast charging
ON
OFF
Charges in 1 hour
Charger pre-charges battery until normal voltage
is reached, then begins fast charge mode. May
take longer than 1 hour to fully charge.
Deeply
Charging
ON
OFF
Discharged
Maintenance
charging
Fast charging is complete;
Charger maintains charge mode.
Full
OFF
ON
Hot battery
Evaluate
When battery pack reaches cooled temperature,
charger begins fast charge mode.
Flashing OFF
Flashing OFF
pack
Cold battery
Whenbatterypackreacheswarmedtemperature,
charger begins fast charge mode.
Evaluate
pack
Defective Defective
Flashing Flashing Battery pack or charger is defective
• If defective, try to repeat the conditions a second time by removing and reinstalling the battery
pack. If the LED status repeats a second time, try charging a different battery.
• If a different battery charges normally, dispose of the defective pack (see Maintenance section).
• If a different battery also indicates “Defective,” the charger may be defective.
13
Download from Www.Somanuals.com. All Manuals Search And Download.
OPERATION
THE FOLLOWING INSTRUCTIONS ARE FOR
RIDGID NICKEL-CADMIUM BATTERY PACKS
AND CHARGERS.
Battery packs for this tool are shipped in a low charge
condition to prevent possible problems. Therefore, you
should charge the pack until the light on the front of the
charger changes from flashing green to continuous green.
NOTE: Batteries will not reach full charge the first time they
are charged. Allow several cycles (operation followed by
recharging) for them to become fully charged. This is normal
for nickel-cadmium batteries.
TO CHARGE
Charge the battery pack only with the charger provided.
Make sure the power supply is normal household voltage,
120 volts, 60 Hz, AC only.
Connect the charger to a power supply.
Attach the battery pack to the charger by aligning the
raised ribs on the battery pack with the grooves in the
charger, then slide the battery pack onto the charger. See
Figure 7.
The battery pack will become slightly warm to the touch
while charging. This is normal and does not indicate a
problem.
Fig. 7
Do not place the charger in an area of extreme heat or
cold. It will work best at normal room temperature.
For average charge times, refer to the chart on the
following page.
When the batteries become fully charged, unplug the
charger from the power supply and remove the battery
pack.
GREEN
LED
RED
LED
POWER
INDICATOR
EVALUATE
INDICATOR
CHARGING A HOT BATTERY PACK
When using the tool continuously, the batteries in the battery
pack will become hot. You should let a hot battery pack
cool down for approximately 30 minutes before attempting
to recharge. When the battery pack becomes discharged
and is hot, the green LED will be off and the red LED will
begin flashing.
DEFECTIVE
INDICATOR
CHARGING
INDICATOR
When the battery pack cools down to approximately 104°F
(40°C), the charger will automatically begin fast charge
mode.
CHARGING A COOL BATTERY PACK
If the battery pack is below normal temperature range, the
red LED will begin flashing and the green LED will be off.
When the battery warms to a temperature of more than 41°F
(5°C), the charger will automatically begin fast charge mode.
NOTE: Refer to CHARGING THE BATTERY PACK for
normal recharging of batteries. If the charger does not charge
your battery pack under normal circumstances, return both
the battery pack and charger to your nearest repair center
for electrical check. For the location of your nearest repair
center, please call 1-866-539-1710.
FULL
INDICATOR
Fig. 8
14
Download from Www.Somanuals.com. All Manuals Search And Download.
OPERATION
LED FUNCTION OF RIDGID NICKEL-CADMIUM CHARGERS
See Figure 8.
LED
INDICATOR
BATTERY
PACK
RED
LED
GREEN
LED
ACTION
Power
Without battery pack ON
OFF
OFF
OFF
Ready to charge battery pack.
When battery pack reaches cooled
temperature, charger begins fast
charge mode.
Evaluate
Evaluate
Hot battery pack
Cold battery pack
Flashing
When battery pack reaches warmed
temperature, charger begins fast
charge mode.
Flashing
Charger pre-charges battery until
normal voltage is reached, then
begins fast charge mode.
Evaluate
Defective
Deeply discharged
Defective
Flashing
Flashing
OFF
Flashing
Battery pack or charger is defective.
• If defective, try to repeat the conditions a second time by removing and reinstalling the battery
pack. If the LED status repeats a second time, try charging a different battery.
• If a different battery charges normally, dispose of the defective pack (see Maintenance section).
• If a different battery also indicates “Defective,” the charger may be defective.
Charging
Full
Fast charging
Slow charging
ON
Flashing
ON
See chart below for charge times.
Fast charging is complete;
charger maintains charge mode.
OFF
BATTERY
COMPACT SERIES
HC
AVERAGE CHARGE TIME
18 min.
27 min.
34 min.
HC 2.5
15
Download from Www.Somanuals.com. All Manuals Search And Download.
OPERATION
LOCK-OFF
BUTTON
WARNING:
Battery tools are always in operating condition.
Therefore, the switch should always be locked
when not in use or carrying at your side.
STARTING/STOPPING THE PLANER
See Figure 9.
To start: Push the lock-off button from either side, and
then depress the switch trigger.
To stop: Release the switch trigger.
TO INSTALL BATTERY PACK
See Figure 10.
Make sure the lock-off button is in the center position.
Slide the battery pack into the tool.
Make sure the latches on each side of the battery pack
snap into place and the battery pack is secured in the
tool before beginning operation.
TO REMOVE BATTERY PACK
See Figure 10.
SWITCH
TRIGGER
Make sure the lock-off button is in the center position.
Locate the latches on the side of the battery pack and
Fig. 9
depress to release the battery pack from the tool.
The battery pack will automatically disconnect in
the direction to be removed when the buttons are
depressed.
18V BATTERY
PACK
LATCH
24V BATTERY
PACK
LATCH
DEPRESS LATCHES TO
RELEASE BATTERY PACK
Fig. 10
16
Download from Www.Somanuals.com. All Manuals Search And Download.
OPERATION
AUTOMATIC REAR STAND
See Figure 11.
The planer has been equipped with an automatic rear stand
that will prevent the blade from contacting the workbench
when not in use. As you begin your planing operation, the
stand will automatically retract as it passes over the edge
of the workpiece. When setting the planer down on your
workbench, the rear stand will automatically pivot down to
prevent the blade from making any contact.
WARNING:
Make sure the automatic rear stand operates freely
at all times and that the area surrounding the stand
is clear of debris. Failure to do so could result in
serious personal injury.
WORKPIECE
AUTOMATIC REAR
STAND
Fig. 11
PLANING DEPTH
See Figure 12.
DEPTH
ADJUSTMENT
KNOB
Always work from a rough cut to a finish cut. The approximate
setting for rough planing is 1/32 in. For finish planing use
a setting of approximately 1/64 in. Make test cuts in scrap
wood after each adjustment to make sure that the planer is
removing the desired amount of wood.
To set the planing depth:
Make sure the lock-off button is in the center position.
NOTE: The switch automatically locks when the lock-off
button is not depressed to the left or the right.
Turn the depth adjustment knob to the desired setting.
NOTE: To protect the blades during storage, transporting,
etc., set the depth adjustment to 0.
Fig. 12
17
Download from Www.Somanuals.com. All Manuals Search And Download.
OPERATION
FRONT
HANDLE
OPERATING THE PLANER
See Figure 13.
Clamp the work securely.
WARNING:
Work moving during a cut could result in loss of
control of the planer and cause serious injury.
Support the work so that the operation is on your right.
REAR
HANDLE
Adjust the planing depth.
Hold the planer with both hands. Hold the front handle
with your left hand and the rear handle with your right
hand.
WARNING:
Always use two hands on the tool for any operation.
This assures that you maintain control and avoid
risk of serious personal injury. Always properly
support and clamp the work so that both hands
are free to control the planer.
DUST BAG
Place the front shoe on the edge of work to be planed.
NOTE: Make sure the blades are not touching the
work.
CLAMP
Apply pressure to the front handle so that the front shoe
is completely flat on the work.
WORKPIECE
Start the planer and let the motor reach maximum
Fig. 13
speed.
Hold the planer firmly and push it forward into the work,
using a slow, steady motion.
CAUTION:
Apply downward pressure toward the rear handle as you
reach the end of the planed cut. This helps keep the rear
section of the planer base in contact with the work and
prevents the front of the planer from gouging the cut.
Planing too fast results in a poor finish and
increases chip build-up in the chip exhaust. Chip
build-up restricts air flow and can cause motor
overheating.
WARNING:
Be careful to avoid hitting nails or any other foreign
objects during planing operation; this action could
nick, crack, or damage blades.
WARNING:
Do not attempt to clear a blocked chip exhaust
until the blades stop and you have removed the
battery. Failure to heed this warning can result in
serious personal injury.
NOTE: We suggest that you always keep an extra set of
blades on hand. As soon as the blades show signs of
becoming dull, replace them.
Plane slowly and empty the dust bag often.
NOTE: Using a battery in a low charge condition will cause
chip build-up and clogging of the chip exhaust. This will
also affect the quality of the cut. Keep a freshly-charged
battery available and replace the discharged battery when
you notice a decrease in performance.
18
Download from Www.Somanuals.com. All Manuals Search And Download.
OPERATION
GROOVE
CHAMFERING
See Figure 14.
The planer is designed with a chamfering groove in the front
shoe to chamfer edges of boards as shown. Before making
a cut on good lumber, practice cutting on scrap lumber to
determine the amount to be removed.
Clamp the work securely.
Hold the front handle with your left hand and the rear
FRONT
HANDLE
handle with your right hand.
Place the chamfering groove on the surface to be cut.
Start the planer and let the motor reach maximum
speed.
Hold the planer firmly and push it forward into the work,
using a slow, steady motion.
Apply downward pressure to keep the planer flat at the
beginning and the end of the work surface.
PLANING EDGES AND MAKING RABBET CUTS
The planer comes with an adjustable edge guide for precision
edge planing and rabbet cutting. Attach the edge guide to
either side of the planer for planing edges. Attach the edge
guide to the left side for making rabbet cuts.
WORKPIECE
ATTACHING THE EDGE GUIDE FOR PLANING
EDGES
See Figure 15.
Remove the battery pack from the tool.
Attach the bracket to the desired side of the planer using
the knob bolt.
CLAMP
Attach the edge guide to the bracket using the knob nut
and the carriage head bolt.
Fig. 14
Tighten the knob nut, knob bolt, and carriage head bolt
securely.
Reinstall the battery pack.
KNOB
BOLT
CARRIAGE
HEAD BOLT
BRACKET
EDGE
GUIDE
KNOB
NUT
Fig. 15
19
Download from Www.Somanuals.com. All Manuals Search And Download.
OPERATION
PLANING EDGES
See Figure 16.
Follow the directions in the “Operating the Planer” section
earlier in this manual. Hold the edge guide firmly against the
edge of the work surface.
ATTACHING THE EDGE GUIDE FOR MAKING
RABBET CUTS
See Figure 15.
Remove the battery pack from the tool.
Attach the bracket to the left side of the planer using the
knob bolt.
Attach the edge guide loosely to the bracket using the
WORKPIECE
knob nut and the carriage head bolt.
Adjust the edge guide to the desired width for the rabbet
cut.
Tighten the retaining knob securely.
EDGE GUIDE
Reinstall the battery pack.
MAKING RABBET CUTS
See Figure 17.
Fig. 16
Follow the directions in the “Operating the Planer” section
earlier in this manual. Hold the edge guide firmly against the
edge of the work surface.
The depth of the rabbet is determined by the depth of the cut
and the number of passes made along the work surface. The
maximum depth of the rabbet cut is 1/2 in. Cuts should be
made in 1/16 in. passes, or less, to reach the desired depth.
The width of the rabbet cut may be adjusted by moving the
edge guide.
WORKPIECE
EDGE GUIDE
Fig. 17
20
Download from Www.Somanuals.com. All Manuals Search And Download.
MAINTENANCE
GENERAL MAINTENANCE
WARNING:
When servicing use only identical RIDGID
replacement parts. Use of any other parts may
create a hazard or cause product damage.
Avoid using solvents when cleaning plastic parts. Most
plastics are susceptible to damage from various types of
commercial solvents and may be damaged by their use. Use
clean cloths to remove dirt, dust, oil, grease, etc.
WARNING:
WARNING:
Do not at any time let brake fluids, gasoline,
petroleum-based products, penetrating oils, etc.,
come in contact with plastic parts. Chemicals can
damage, weaken or destroy plastic which may
result in serious personal injury.
Always wear safety goggles or safety glasses with
side shields during power tool operation or when
blowing dust. If operation is dusty, also wear a
dust mask.
Only the parts shown on the parts list are intended to be
repaired or replaced by the customer. All other parts should
be replaced at a RIDGID authorized service center.
WARNING:
To avoid serious personal injury, always remove
the battery pack from the tool when cleaning or
performing any maintenance.
BATTERY PACK REMOVAL AND PREPARATION
BATTERIES
This tool will accept 24V lithium-ion batteries or 18V nickel-
cadmium batteries. Length of service from each charging
will depend on the type of work you are doing.
FOR RECYCLING
To preserve natural resources, please
recycle or dispose of batteries properly.
The batteries for this tool have been designed to provide
maximum trouble-free life. However, like all batteries, they
will eventually wear out. Do not disassemble battery pack
and attempt to replace the batteries. Handling of these
batteries, especially when wearing rings and jewelry, could
result in a serious burn.
This product uses lithium-ion or nickel-
cadmium batteries. Local, state or federal
laws may prohibit disposal of batteries in
ordinary trash.
Li - Ion
Consult your local waste authority for
information regarding available recycling
and/or disposal options.
To obtain the longest possible battery life, we suggest the
following:
For lithium-ion batteries:
Remove the battery pack from the charger once it is fully
WARNING:
charged and ready for use.
Upon removal, cover the battery pack’s terminals
with heavy-duty adhesive tape. Do not attempt to
destroy or disassemble battery pack or remove
any of its components. Lithium-ion and nickel-
cadmium batteries must be recycled or disposed
of properly. Also, never touch both terminals with
metal objects and/or body parts as short circuit
may result. Keep away from children. Failure to
comply with these warnings could result in fire
and/or serious injury.
For battery pack storage longer than 30 days:
Store the battery pack where the temperature is below
80°F and away from moisture.
Store battery packs in a 30%-50% charged condition.
Every six months of storage, charge the pack as
normal.
For nickel-cadmium batteries:
Remove the battery pack from the charger once it is fully
charged and ready for use.
For battery pack storage longer than 30 days:
Store the battery pack where the temperature is below
80°F.
Store battery packs in a “discharged” condition.
21
Download from Www.Somanuals.com. All Manuals Search And Download.
MAINTENANCE
REPLACING BLADES
See Figures 18 - 19.
BLADE
Always replace blades in pairs. Do not attempt to sharpen
blades. If the blades become dull, replace them.
BLADE CLAMP
SCREWS
BLADE
WRENCH
When replacing the blades, use recommended replacement
blade only, RIDGID part number 671480001.
WARNING:
Blades are sharp. Use extreme caution when
replacing the blades. Failure to heed this warning
can result in serious personal injury.
Remove the battery pack from the tool.
Secure the planer in an upside-down position.
Loosen the three screws securing the blade and blade
clamp on the blade holder using the blade wrench pro-
vided.
NOTE: Before removing the old blades, take notice of
the direction of cut as well as how the tapered edge of
the old blades are oriented. The tapered edge of the new
blades must be in the same orientation as the original
blades, with the tapered edge on the same side as the
screw heads and the flat edge facing the cylinder.
Fig. 18
BLADE
Remove the blade and blade clamp.
TAPERED
EDGE OF
BLADE
Remove the old blade from the blade holder.
Clean any sawdust or wood chips from around the blade
area.
BLADE
CLAMP
Place the new blade in position on the blade holder, with
the three screws aligned with the screw holes.
Replace the blade clamp.
Replace and retighten the three blade-securing screws
using the blade wrench.
Repeat the above procedure to change the other
blade.
BLADE
HOLDER
BLADE
SCREWS
Fig. 19
22
Download from Www.Somanuals.com. All Manuals Search And Download.
MAINTENANCE
REPLACING THE BELT
See Figures 20 - 21.
SMALL
PULLEY
BELT
COVER
When replacing the belt, use the recommended replacement
belt only, RIDGID part number 570279001.
Remove the battery pack from the tool.
Remove belt cover screws.
Remove the belt cover.
Remove the old drive belt from the large pulley by turning
the small pulley in a counterclockwise direction. As you
turn the belt, pull and work it off the large pulley until it
has been completely removed from both pulleys.
LARGE
PULLEY
BELT
Install the new belt over the small pulley. As you turn the
belt, push and work it onto the large pulley, turning the
pulley clockwise until the belt is in place.
SCREWS
Fig. 20
Replace the belt cover.
Install belt cover screws and tighten securely, but do not
overtighten.
CLEANING THE CHIP EXHAUST AND EMPTY-
ING THE DUST BAG
See Figure 22.
After using the planer for an extended period of time or when
planing wet or green lumber, chips may build up in the chip
exhaust. Chip build-up restricts air flow and causes the
motor to overheat. Clean the chip exhaust port and empty
the dust bag regularly.
SMALL
PULLEY
Remove the battery pack from the tool.
Remove the dust bag from the exhaust port.
Clean the build-up from the exhaust port with a small
LARGE
PULLEY
BELT
piece of wood. Do not use your hands or fingers.
Unzip the dust bag.
Fig. 21
Empty all debris from the dust bag and ensure that the
collar is free of debris.
Replace the dust bag.
CHIP EXHAUST
DUST BAG
Fig. 22
23
Download from Www.Somanuals.com. All Manuals Search And Download.
NOTES
24
Download from Www.Somanuals.com. All Manuals Search And Download.
WARRANTY
RIDGID® HAND HELD AND STATIONARY POWER TOOL 3 YEAR LIMITED SERVICE WARRANTY
Proof of purchase must be presented when requesting war-
ranty service.
WHAT IS NOT COVERED
This warranty applies only to the original purchaser at retail
and may not be transferred. This warranty only covers de-
fects arising under normal usage and does not cover any
malfunction, failure or defect resulting from misuse, abuse,
neglect, alteration, modification or repair by other than an
authorized service center for RIDGID® branded hand held
and stationary power tools. Consumable accessories pro-
vided with the tool such as, but not limited to, blades, bits
and sand paper are not covered.
Limited to RIDGID® hand held and stationary power tools
purchased 2/1/04 and after. This product is manufactured
by One World Technologies, Inc. The trademark is licensed
from RIDGID, Inc. All warranty communications should be
directed to One World Technologies, Inc., attn: RIDGID Hand
Held and Stationary Power Tool Technical Service at (toll
free) 1-866-539-1710.
90-DAY SATISFACTION GUARANTEE POLICY
During the first 90 days after the date of purchase, if you are
dissatisfied with the performance of this RIDGID® Hand Held
and Stationary Power Tool for any reason you may return
the tool to the dealer from which it was purchased for a full
refund or exchange. To receive a replacement tool you must
present proof of purchase and return all original equipment
packaged with the original product. The replacement tool
will be covered by the limited warranty for the balance of
the 3 YEAR service warranty period.
RIDGID, INC. AND ONE WORLD TECHNOLOGIES, INC.
MAKE NO WARRANTIES, REPRESENTATIONS OR
PROMISES AS TO THE QUALITY OR PERFORMANCE
OF ITS POWER TOOLS OTHER THAN THOSE SPECIFI-
CALLY STATED IN THIS WARRANTY.
ADDITIONAL LIMITATIONS
To the extent permitted by applicable law, all implied war-
ranties, including warranties of MERCHANTABILITY or FIT-
NESS FOR A PARTICULAR PURPOSE, are disclaimed. Any
implied warranties, including warranties of merchantability
or fitness for a particular purpose, that cannot be disclaimed
under state law are limited to three years from the date of
purchase. One World Technologies, Inc. and RIDGID, Inc.
are not responsible for direct, indirect, incidental or conse-
quential damages. Some states do not allow limitations on
how long an implied warranty lasts and/or do not allow the
exclusion or limitation of incidental or consequential dam-
ages, so the above limitations may not apply to you. This
warranty gives you specific legal rights, and you may also
have other rights which vary from state to state.
WHAT IS COVERED UNDER THE 3 YEAR
LIMITED SERVICE WARRANTY
This warranty on RIDGID® Hand Held and Stationary Power
Tools covers all defects in workmanship or materials and nor-
mal wear items such as brushes, chucks, motors, switches,
cords, gears and even cordless batteries in this RIDGID®
tool for three years following the purchase date of the tool.
Warranties for other RIDGID® products may vary.
HOW TO OBTAIN SERVICE
To obtain service for this RIDGID® tool you must return it;
freight prepaid, or take it in to an authorized service center
for RIDGID® branded hand held and stationary power tools.
You may obtain the location of the authorized service center
nearest you by calling (toll free) 1-866-539-1710 or by log-
ging on to the RIDGID® website at www.ridgid.com. When
requesting warranty service, you must present the original
dated sales receipt. The authorized service center will re-
pair any faulty workmanship, and either repair or replace
any part covered under the warranty, at our option, at no
charge to you.
One World Technologies, Inc.
P.O. Box 35, Hwy. 8
Pickens, SC 29671
25
Download from Www.Somanuals.com. All Manuals Search And Download.
OPERATOR’S MANUAL
18 VOLT/24 VOLT
MaxSelect™ HAND PLANER
WITH SPIRAL CUT
R888
Customer Service Information:
For parts or service, contact your nearest RIDGID authorized service center. Be
sure to provide all relevant information when you call or visit. For the location of
the authorized service center nearest you, please call 1-866-539-1710 or visit us
The model number of this tool is found on a plate attached to the motor housing.
Please record the serial number in the space provided below. When ordering repair
parts, always give the following information:
R888
Model No.
Serial No.
983000-989
8-04-2006 (REV:00)
Download from Www.Somanuals.com. All Manuals Search And Download.
|