OPERATOR’S MANUAL
13 in. THICKNESS PLANER
R4330
Your new planer has been engineered and manufactured to our high standards for dependability, ease of operation, and
operator safety. When properly cared for, it will give you years of rugged, trouble-free performance.
WARNING:
To reduce the risk of injury, the user must read and understand the operator’s manual before using this product.
Thank you for buying a RIDGID® product.
SAVE THIS MANUAL FOR FUTURE REFERENCE
Download from Www.Somanuals.com. All Manuals Search And Download.
GENERAL SAFETY RULES
ALWAYS WEAR SAFETY GLASSES WITH SIDE
SHIELDS. Everyday eyeglasses have only impact-
resistant lenses, they are NOT safety glasses.
WARNING:
Read and understand all instructions. Failure to
follow all instructions listed below, may result in
electric shock, fire and/or serious personal injury.
SECURE WORK. Useclampsoravisetoholdworkwhen
practical. It’s safer than using your hand and frees both
hands to operate tool.
DON’T OVERREACH. Keep proper footing and
READ ALL INSTRUCTIONS
balance at all times.
KNOWYOURPOWERTOOL.Readtheoperator’smanual
carefully. Learn the tool’s applications and limitations
as well as the specific potential hazards related to this
tool.
MAINTAIN TOOLS WITH CARE. Keep tools sharp
andcleanforbetterandsaferperformance.Followinstruc-
tions for lubricating and changing accessories.
DISCONNECT TOOLS. When not in use, before
servicing, or when changing attachments, blades, bits,
cutters, etc., all tools should be disconnected.
GUARDAGAINSTELECTRICALSHOCKbYPREVENT-
ING bODY CONTACT WITH GROUNDED SURFACES.
For example: pipes, radiators, ranges, refrigerator enclo-
sures.
AVOID ACCIDENTAL STARTING. Be sure switch is off
when plugging in any tool.
KEEP GUARDS IN PLACE and in good working order.
USE RECOMMENDED ACCESSORIES. Consult the
operator’s manual for recommended accessories. The
use of improper accessories may risk injury.
REMOVE ADJUSTING KEYS AND WRENCHES. Form
habitofcheckingtoseethatkeysandadjustingwrenches
are removed from tool before turning it on.
NEVER STAND ON TOOL. Serious injury could occur if
the tool is tipped or if the cutting tool is unintentionally
contacted.
KEEPWORKAREACLEAN.Clutteredareasandbenches
invite accidents. DO NOT leave tools or pieces of wood
on the tool while it is in operation.
CHECK DAMAGED PARTS. Before further use of the
tool, a guard or other part that is damaged should be
carefullycheckedtodeterminethatitwilloperateproperly
and perform its intended function. Check for alignment
of moving parts, binding of moving parts, breakage of
parts, mounting and any other conditions that may affect
its operation. A guard or other part that is damaged must
be properly repaired or replaced by an authorized service
center to avoid risk of personal injury.
DO NOT USE IN DANGEROUS ENVIRONMENTS. Do
not use power tools in damp or wet locations or expose
to rain. Keep the work area well lit.
KEEP CHILDREN AND VISITORS AWAY. All visi-
tors should wear safety glasses and be kept a safe
distance from work area. Do not let visitors contact
tool or extension cord while operating.
MAKE WORKSHOP CHILDPROOF with padlocks and
master switches, or by removing starter keys.
USE THE RIGHT DIRECTION OF FEED. Feed work into
a blade or cutter against the direction of rotation of blade
or cutter only.
DON’T FORCE TOOL. It will do the job better and safer
at the feed rate for which it was designed.
NEVER LEAVE TOOL RUNNING UNATTENDED. TURN
THE POWER OFF. Don’t leave tool until it comes to a
complete stop.
USE RIGHT TOOL. Don’t force the tool or attachment to
do a job it was not designed for. Don’t use it for a purpose
not intended.
PROTECT YOUR LUNGS. Wear a face or dust mask if
USE THE PROPER ExTENSION CORD. Makesureyour
extensioncordisingoodcondition.Useonlyacordheavy
enough to carry the current your product will draw. An
undersized cord will cause a drop in line voltage result-
ing in loss of power and overheating. A wire gauge size
(A.W.G.) of at least 12 is recommended for an extension
cord 50 feet or less in length. If in doubt, use the next
heaviergauge.Thesmallerthegaugenumber,theheavier
the cord.
the cutting operation is dusty.
PROTECT YOUR HEARING. Wear hearing protection
during extended periods of operation.
DO NOT AbUSE CORD. Never yank cord to disconnect
from receptacle. Keep cord from heat, oil, and sharp
edges.
USE OUTDOOR ExTENSION CORDS. When tool
is used outdoors, use only extension cords with
approved ground connection that are intended for use
outdoors and so marked.
DRESS PROPERLY. Do not wear loose clothing, gloves,
neckties, or jewelry. They can get caught and draw you
into moving parts. Rubber gloves and nonskid footwear
are recommended when working outdoors. Also wear
protective hair covering to contain long hair.
NEVER USE IN AN ExPLOSIVE ATMOSPHERE.
Normal sparking of the motor could ignite fumes.
3
Download from Www.Somanuals.com. All Manuals Search And Download.
GENERAL SAFETY RULES
INSPECT TOOL CORDS PERIODICALLY. If dam-
aged, have repaired by a qualified service technician at
anauthorizedservicefacility.Theconductorwithinsulation
havinganoutersurfacethatisgreenwithorwithoutyellow
stripes is the equipment-grounding conductor. If repair
or replacement of the electric cord or plug is necessary,
do not connect the equipment-grounding conductor to a
live terminal. Repair or replace a damaged or worn cord
immediately. Stay constantly aware of cord location and
keep it well away from the rotating blade.
use brake fluids, gasoline, petroleum-based products, or
any solvents to clean tool.
STAY ALERT AND ExERCISE CONTROL. Watch what
you are doing and use common sense. Do not operate
tool when you are tired. Do not rush.
DO NOT USE TOOL IF SWITCH DOES NOT TURN IT
ON AND OFF. Have defective switches replaced by an
authorized service center.
NEVER TOUCH bLADE or other moving parts during
use.
INSPECT ExTENSION CORDS PERIODICALLY and
NEVER START A TOOL WHEN ANY ROTATING
COMPONENT IS IN CONTACT WITH THE
WORKPIECE.
replace if damaged.
GROUND ALL TOOLS. If tool is equipped with three-
prong plug, it should be plugged into a three-hole
electrical receptacle.
DO NOT OPERATE A TOOL WHILE UNDER THE
INFLUENCE OF DRUGS, ALCOHOL, OR ANY
MEDICATION.
CHECK WITH A QUALIFIED ELECTRICIAN or service
personnelifthegroundinginstructionsarenotcompletely
understoodorifindoubtastowhetherthetoolisproperly
grounded.
WHEN SERVICING useonlyidenticalreplacementparts.
Use of any other parts may create a hazard or cause
product damage.
USE ONLY CORRECT ELECTRICAL DEVICES: 3-wire
extension cords that have 3-prong grounding plugs and
3-pole receptacles that accept the tool’s plug.
USE ONLY RECOMMENDED ACCESSORIES listed
in this manual or addendums. Use of accessories that
are not listed may cause the risk of personal injury.
Instructions for safe use of accessories are included
with the accessory.
DO NOT MODIFY the plug provided. If it will not fit the
outlet, have the proper outlet installed by a qualified
electrician.
DOUbLE CHECK ALL SETUPS. Makesurebladeistight
and not making contact with tool or workpiece before
connecting to power supply.
KEEP TOOL DRY, CLEAN, AND FREE FROM OIL AND
GREASE. Always use a clean cloth when cleaning. Never
SPECIFIC SAFETY RULES
bEFORE STARTING UP, recheck to make certain all
NEVER PERFORM THE PLANING OPERATION with
holding screws are tight.
the cutterhead or dust hood removed.
STOP THE MACHINE and recheck the hex head bolts
and blades for tightness after about 50 hours of opera-
tion.
NEVER MAKE A PLANING CUT deeper than 1/8 in.
DO NOT PLANE MATERIAL shorter than 14 in. or
narrower than 3/4 in.
DO NOT FORCE FEED THE WORKPIECE through the
MAINTAIN THE PROPER RELATIONSHIP between the
infeed and outfeed surfaces and the cutterhead blade
path.
machine. Let the planer apply the proper feed rate.
CHECK THE FEED ROLLERS occasionally to be sure
there are no chips or sawdust between any compo-
nents.
SUPPORT THE WORKPIECE ADEQUATELY at all
times during operation; maintain control of the work at
all times.
PLANE ONLY SOUND LUMbER; there should be no
loose knots and as few tight knots as possible. Make sure
the workpiece is free from nails, screws, stones, or other
foreign objects that could break or chip the blades.
NEVER FEED THE WORK from the rear of the planer.
DO NOT ATTEMPT TO PERFORM an abnormal or little
used operation without the use of sturdy and adequate
jigs, fixtures, stops, and the like.
NEVER STAND DIRECTLY IN LINE witheithertheinfeed
or outfeed sides. Stand off to one side.
NEVER plane more than one piece at a time. DO NOT
PLANE more than one workpiece on the planer table at
a time.
MAKESURETHEbLADESAREATTACHEDasdescribed
in the operation section. The blades are sharp and can
easily cut your hand. Use caution in handling the blades
and cutterhead guard.
4
Download from Www.Somanuals.com. All Manuals Search And Download.
SPECIFIC SAFETY RULES
NEVERPUTYOURFINGERSintothedusthoodorunder
ALWAYS TURN OFF TOOL before disconnecting it to
avoid accidental starting when reconnecting to power
supply.
the cutter guard.
ALLOW THE CUTTERHEAD to reach full speed before
IF THE POWER SUPPLY CORD IS DAMAGED, it must
be replaced only by the manufacturer or by an authorized
service center to avoid risk.
using the planer.
REPLACEMENTPARTS.Allrepairs,whetherelectricalor
mechanical, should be made at your nearest authorized
service center.
THIS TOOL should have the following markings:
a) Wear eye protection.
DO NOT attempt to turn cutterhead with hands.
b) Keep hands away from cutterhead.
c) Do not operate saw without guards in place.
d) Do not perform any operation freehand.
e) Never reach around saw blade.
f) Turn off tool and wait for blades to stop before
moving workpiece or changing settings.
g) Disconnect power (or unplug tool as applicable)
before changing blades or servicing.
h) No load speed.
IF ANY PART OF THIS TOOL IS MISSING or should
break, bend, or fail in any way, or should any electrical
component fail to perform properly, shut off the power
switch, remove the plug from the power source, and
have damaged, missing, or failed parts replaced before
resuming operation.
ALWAYS STAY ALERT! Do not allow familiarity (gained
from frequent use of your planer) to cause a careless
mistake. ALWAYS REMEMbER that a careless fraction
of a second is sufficient to inflict serious injury.
SAVE THESE INSTRUCTIONS. Refer to them
frequently and use to instruct other users. If you loan
someone this tool, loan them these instructions also.
MAKESURETHEWORKAREAHASAMPLELIGHTING
toseetheworkandthatnoobstructionswillinterferewith
safe operation bEFORE performing any work using your
planer.
WARNING:
Some dust created by power sanding, sawing, grinding, drilling, and other construction activities contains chemi-
cals known to cause cancer, birth defects or other reproductive harm. Some examples of these chemicals are:
• lead from lead-based paints,
• crystalline silica from bricks and cement and other masonry products, and
• arsenic and chromium from chemically-treated lumber.
Your risk from these exposures varies, depending on how often you do this type of work. To reduce your
exposure to these chemicals: work in a well ventilated area, and work with approved safety equipment, such as
those dust masks that are specially designed to filter out microscopic particles.
5
Download from Www.Somanuals.com. All Manuals Search And Download.
SYMbOLS
Some of the following symbols may be used on this tool. Please study them and learn their meaning. Proper interpreta-
tion of these symbols will allow you to operate the tool better and safer.
SYMbOL
NAME
DESIGNATION/ExPLANATION
V
Volts
Voltage
Current
A
Hz
W
Amperes
Hertz
Frequency (cycles per second)
Watt
Power
min
Minutes
Time
Alternating Current
Type of current
Direct Current
Type or a characteristic of current
Rotational speed, at no load
n
No Load Speed
o
Class II Construction
Per Minute
Double-insulated construction
Revolutions, strokes, surface speed, orbits etc., per minute
.../min
Do not expose to rain or use in damp locations.
Wet Conditions Alert
To reduce the risk of injury, user must read and understand
operator’s manual before using this product.
Read The Operator’s Manual
Always wear safety goggles, safety glasses with side shields, or
a full face shield when operating this product.
Eye Protection
Safety Alert
Precautions that involve your safety.
Failure to keep your hands away from the blade will result in
serious personal injury.
No Hands Symbol
To reduce the risk of injury or damage, avoid contact with any
hot surface.
Hot Surface
6
Download from Www.Somanuals.com. All Manuals Search And Download.
SYMbOLS
The following signal words and meanings are intended to explain the levels of risk associated with this product.
SYMbOL
SIGNAL
MEANING
Indicates an imminently hazardous situation, which, if not avoided, will
result in death or serious injury.
DANGER:
Indicates a potentially hazardous situation, which, if not avoided, could
result in death or serious injury.
WARNING:
CAUTION:
Indicates a potentially hazardous situation, which, if not avoided, may
result in minor or moderate injury.
(Without Safety Alert Symbol) Indicates a situation that may result in
property damage.
CAUTION:
SERVICE
WARNING:
Servicing requires extreme care and knowledge and should
be performed only by a qualified service technician. For
service we suggest you return the product to your nearest
AUTHORIZED SERVICE CENTER for repair. When servic-
ing, use only identical replacement parts.
To avoid serious personal injury, do not attempt
to use this product until you read thoroughly and
understand completely the operator’s manual.
If you do not understand the warnings and
instructions in the operator’s manual, do not use
this product. Call RIDGID® customer service for
assistance.
WARNING:
The operation of any power tool can result in foreign objects being thrown into your eyes, which can result
in severe eye damage. Before beginning power tool operation, always wear safety goggles or safety
glasses with side shields and, when needed, a full face shield. We recommend Wide Vision Safety Mask
for use over eyeglasses or standard safety glasses with side shields. Always use eye protection which
is marked to comply with ANSI Z87.1.
SAVE THESE INSTRUCTIONS
7
Download from Www.Somanuals.com. All Manuals Search And Download.
ELECTRICAL
ExTENSION CORDS
SPEED AND WIRING
Use only 3-wire extension cords that have 3-prong ground-
ing plugs and 3-pole receptacles that accept the tool’s plug.
When using a power tool at a considerable distance from the
power source, use an extension cord heavy enough to carry
the current that the tool will draw. An undersized extension
cord will cause a drop in line voltage, resulting in a loss of
power and causing the motor to overheat. Use the chart
provided below to determine the minimum wire size required
in an extension cord. Only round jacketed cords listed by
Underwriter's Laboratories (UL) should be used.
Theno-loadspeedofthistoolisapproximately10,000RPM.
This speed is not constant and decreases under a load or
with lower voltage. For voltage, the wiring in a shop is as
important as the motor’s horsepower rating. A line intended
only for lights cannot properly carry a power tool motor. Wire
that is heavy enough for a short distance will be too light for
a greater distance. A line that can support one power tool
may not be able to support two or three tools.
GROUNDING INSTRUCTIONS
**Ampere rating (on tool faceplate)
In the event of a malfunction or breakdown, grounding
provides a path of least resistance for electric current to
reduce the risk of electric shock. This tool is equipped
with an electric cord having an equipment-grounding
conductor and a grounding plug. The plug must be plugged
intoamatchingoutletthatisproperlyinstalledandgrounded
in accordance with all local codes and ordinances.
0-ꢀ.0
ꢀ.1-3.4
3.5-5.0
5.1-7.0 7.1-1ꢀ.0 1ꢀ.1-16.0
Cord Length
Wire Size (A.W.G.)
ꢀ5'
50'
16
16
16
16
16
16
16
16
14
16
14
1ꢀ
14
14
10
14
1ꢀ
—
100'
Do not modify the plug provided. If it will not fit the outlet,
have the proper outlet installed by a qualified electrician.
Improperconnectionoftheequipment-groundingconductor
can result in a risk of electric shock. The conductor with
insulation having an outer surface that is green with or with-
out yellow stripes is the equipment-grounding conductor. If
repair or replacement of the electric cord or plug is neces-
sary, do not connect the equipment-grounding conductor
to a live terminal.
**Used on 12 gauge - 20 amp circuit.
NOTE: AWG = American Wire Gauge
When working with the tool outdoors, use an extension cord
that is designed for outside use. This is indicated by the
letters “WA” on the cord’s jacket.
Before using an extension cord, inspect it for loose or
exposed wires and cut or worn insulation.
Check with a qualified electrician or service personnel if the
grounding instructions are not completely understood, or if
in doubt as to whether the tool is properly grounded.
WARNING:
Keep the extension cord clear of the working area.
Position the cord so that it will not get caught on
lumber, tools or other obstructions while you are
working with a power tool. Failure to do so can
result in serious personal injury.
Repair or replace a damaged or worn cord immediately.
This tool is intended for use on a circuit that has an outlet
like the one shown in figure 1. It also has a grounding pin
like the one shown.
WARNING:
Check extension cords before each use. If
damaged replace immediately. Never use tool with
a damaged cord since touching the damaged area
could cause electrical shock resulting in serious
injury.
ELECTRICAL CONNECTION
This tool is powered by a precision built electric motor. It
should be connected to a power supply that is 120 V, 60
Hz, AC only (normal household current). Do not operate
this tool on direct current (DC). A substantial voltage drop
will cause a loss of power and the motor will overheat. If the
tool does not operate when plugged into an outlet, double
check the power supply.
GroundinG
Pin
120 V Grounded outlet
Fig. 1
8
Download from Www.Somanuals.com. All Manuals Search And Download.
ELECTRICAL
MOTOR SAFETY PROTECTION
This motor should be blown out or vacuumed frequently to
prevent sawdust buildup which can interfere with normal
motor ventilation.
Connect this tool to a power source with the appropriate
voltage for your model and a 15-amp branch circuit with
a 15-amp time delay fuse or circuit breaker. Using the
wrong size fuse can damage the motor.
oVerloAd
ProteCtor / reSet
Button
If the motor won’t start, turn off the power switch
immediately and unplug the tool. Check the cutterhead
to make sure it turns freely. If the head is free, try to start
the motor again. If the motor still does not start, refer to
the Troubleshooting section.
Frequent “blowing” of fuses or tripping of circuit breakers
may result if:
Fig. ꢀ
Improper or dull blades are used.
NOTE: Do not continuously use the thickness planer set
at maximum depth of cut (1/8 in.) and at full 13 in. width
of cut. Continuous use at maximum cutting capacity will
damage your motor.
MOTOR OVERLOAD PROTECTOR
See Figure 2.
WARNING:
Motorisoverloaded.Overloadingcanoccurifaworkpiece
To reduce the risk of serious personal injury from
thrown objects or blade contact from unexpected
starting, immediately turn off the tool if the
protector stops the motor. Remove the switch
key and allow the motor time to cool.
is fed too rapidly or if the tool is misaligned.
Motor circuit is fused differently from recommendations.
Always follow instructions for the proper fuse / breaker.
Do not use a fuse/breaker of greater capacity without
consulting a qualified electrician.
Lowvoltage.Althoughthemotorisdesignedforoperation
on the voltage and frequency specified on the motor,
normal loads will be handled safely on voltage no more
than ten percent above or below that figure. Heavy loads,
however, require that voltage at motorterminals equal the
voltage specified on the motor.
This planer is equipped with a overload protector device
which will automatically “trip” and cause the planer to shut
down if the motor is overheating due to continuous heavy
cutting.
The planer overload protector can only be reset manually
by the user after the planer has been allowed to adequately
cool. Allow 15 - 30 minutes.
NOTE: Always check the connections, the load, and the
supply circuit whenever the motor fails to perform satis-
factorily.
Should the overload protector “trip”:
Turn switch OFF ( O ).
Raise carriage and remove board.
After 15 - 30 minutes, reset the overload protector by
pushing the red reset button on the front of the tool. An
audible click will indicate the overload protector is reset.
Once the button is reset, the tool may be started and
operated as normal.
NOTE:Iftheredbuttonwon’tclickintoplaceimmediately,
the motor is still too hot and must be allowed to cool.
If motor has cooled, button will remain in.
9
Download from Www.Somanuals.com. All Manuals Search And Download.
GLOSSARY OF TERMS
Non-Through Cuts
Any cutting operation where the blade does not extend
completely through the thickness of the workpiece.
Anti-Kickback Pawls (radial arm and table saws)
A device which, when properly installed and maintained,
is designed to stop the workpiece from being kicked back
toward the front of the saw during a ripping operation.
Push blocks (for jointer planers)
Device used to feed the workpiece over the jointer planer
cutterhead during any operation. This aid helps keep the
operator's hands well away from the cutterhead.
Arbor
The shaft on which a blade or cutting tool is mounted.
bevel Cut
A cutting operation made with the blade at any angle other
Push blocks and Push Sticks (for table saws)
than 90° to the table surface.
Devices used to feed the workpiece through the saw blade
during cutting operations. A push stick (not a push block)
should be used for narrow ripping operations. These aids
help keep the operator's hands well away from the blade.
Chamfer
A cut removing a wedge from a block so the end (or part of
the end) is angled rather than at 90°.
Pilot Hole (drill presses)
A small hole drilled in a workpiece that serves as a guide for
drilling large holes accurately.
Compound Cut
A cross cut made with both a miter and a bevel angle.
Cross Cut
Resaw
A cutting or shaping operation made across the grain or the
width of the workpiece.
A cutting operation to reduce the thickness of the workpiece
to make thinner pieces.
Cutterhead (planers and jointer planers)
A rotating cutterhead with adjustable blades or knives. The
blades or knives remove material from the workpiece.
Resin
A sticky, sap-based substance that has hardened.
Revolutions Per Minute (RPM)
The number of turns completed by a spinning object in one
minute.
Dado Cut
A non-through cut which produces a square-sided notch or
trough in the workpiece (requires a special blade).
Ripping or Rip Cut
A cutting operation along the length of the workpiece.
Featherboard
A device used to help control the workpiece by guiding
it securely against the table or fence during any ripping
operation.
Riving Knife/Spreader/Splitter (table saws)
A metal piece, slightly thinner than the blade, which helps
keep the kerf open and also helps to prevent kickback.
FPM or SPM
Feet per minute (or strokes per minute), used in reference
to blade movement.
Saw blade Path
The area over, under, behind, or in front of the blade. As it
applies to the workpiece, that area which will be or has been
cut by the blade.
Freehand
Performing a cut without the workpiece being guided by a
fence, miter gauge, or other aids.
Set
The distance that the tip of the saw blade tooth is bent (or
set) outward from the face of the blade.
Gum
A sticky, sap-based residue from wood products.
Snipe (planers)
Heel
Depression made at either end of a workpiece by cutter
blades when the workpiece is not properly supported.
Alignment of the blade to the fence.
Kerf
Through Sawing
Any cutting operation where the blade extends completely
through the thickness of the workpiece.
The material removed by the blade in a through cut or the
slot produced by the blade in a non-through or partial cut.
Kickback
A hazard that can occur when the blade binds or stalls,
throwing the workpiece back toward operator.
Throw-back
The throwing back of a workpiece usually caused by the
workpiece being dropped into the blade or being placed
inadvertently in contact with the blade.
Leading End
The end of the workpiece pushed into the tool first.
Miter Cut
Workpiece or Material
The item on which the operation is being done.
A cutting operation made with the workpiece at any angle
to the blade other than 90°.
Worktable
Surface where the workpiece rests while performing a
cutting, drilling, planing, or sanding operation.
10
Download from Www.Somanuals.com. All Manuals Search And Download.
FEATURES
PRODUCT SPECIFICATIONS
Feed Rate...............................................................ꢀ6 FPM
Input ..................................1ꢀ0 V, 60 Hz, AC Only, 15 Amp
No Load Speed ...................................10,000 r/min. (RPM)
Max. Planing Height .....................................................6 in.
Max. Planing Width ....................................................13 in.
Max. Planing Depth...................................................1/8 in.
Cord
StorAGe
BlAde / tool
StorAGe
reSet
Button
dePth
AdjuStment
hAndwheel
SwitCh ASSemBly
And SwitCh key
outFeed tABle
extenSion
ind-i-Cut™
dePth GAuGe
rePeAt-A-Cut™
inFeed tABle
extenSion
thiCkneSS SCAle
Fig. 3
11
Download from Www.Somanuals.com. All Manuals Search And Download.
FEATURES
KNOW YOUR PLANER
IND-I-CUT™ DEPTH GAUGE
See Figure 3.
The Ind-I-Cut™ depth gauge is located on the front of your
planer and measures depth of cuts up to 1/8 in.
The safe use of this product requires an understanding of
the information on the tool and in this operator’s manual as
wellasaknowledgeoftheprojectyouareattempting.Before
use of this product, familiarize yourself with all operating
features and safety rules.
REPEAT-A-CUT™
The Repeat-A-Cut™, located on the right side of the planer,
has preset measurements for repetitive planing.
RESET bUTTON
Opens the power line circuit when the motor temperature
exceeds a safe level, when the motor is overloaded, or when
a lower voltage condition exists.
15 AMP MOTOR
Theplanerhasapowerful15ampmotorwithsufficientpower
to handle tough cutting jobs.
AUTOMATIC FEED
Infeed and outfeed rollers feed the wood through the
planer.
SCALE
Quickly check the thickness of a workpiece.
SWITCH ASSEMbLY AND SWITCH KEY
The planer has an easy access switch. To lock in the OFF
position, remove the switch key. Place the key in a location
inaccessible to children and others not qualified to use the
tool.
bLADE / TOOL STORAGE
A magnetic blade tool and 4 mm hex key are located in
blade / tool storage under the rear table extension. For your
convenience, an extra set of blades can be stored in the
blade / tool storage.
TAbLE ExTENSIONS
Infeed and outfeed table extensions are attached to the
machine and fold upright for easy storage. These table ex-
tensions are helpful when planing long workpieces.
DEPTH ADJUSTMENT HANDWHEEL
The depth adjustment handwheel is used to raise and lower
the cutterhead assembly.
DUST HOOD
Attaching either a ꢀ-1/ꢀ in. or 4 in. shop vac hose to the
dust hood helps minimize sawdust accumulation on the
workpiece.
THICKNESS SCALE
The thickness scale accurately displays the height of the
cutter blades to a maximum of 6 in.
TOOLS NEEDED
The following tools (not included) are needed for assembly and alignment:
FrAminG SquAre
Fig. 4
1ꢀ
Download from Www.Somanuals.com. All Manuals Search And Download.
LOOSE PARTS
The following items are included with the tool:
Blade / tool storage
Dust hood
Switch key
Dust hood knobs (ꢀ)
Handwheel knob
Operator’s manual
Hex key (4 mm)
Magnetic blade tool
Hex head screw (ꢀ)
Depth adjustment handwheel
duSt hood
knoBS
duSt
hood
SwitCh key
hex
heAd
SCrew
hex
heAd
SCrew
hex key
mAGnetiC
BlAde tool
dePth
AdjuStment
hAndwheel
hAndwheel
knoB
BlAde / tool
StorAGe
Fig. 5
WARNING:
The use of attachments or accessories not listed might be hazardous and could cause serious personal injury.
13
Download from Www.Somanuals.com. All Manuals Search And Download.
ASSEMbLY
Mark holes on workbench where planer is to be mounted
UNPACKING
This product requires assembly.
using holes in planer base as a template for hole pattern.
Drill four holes through workbench.
NOTE: Every RIDGID® Thickness Planer is tested at the
factorytoinsureitsperformance.Youmayseesmallamounts
of wood dust and chips on your new planer.
Carefully lift the tool from the carton and place it on a
level work surface.
Place planer on workbench aligning holes in the planer
base with holes drilled in the workbench.
Insert four bolts (not included) and tighten securely with
lock washers and hex nuts (not included).
NOTE: This tool is heavy. To avoid back injury, lift with
your legs, not your back, and get help when needed.
Inspect the tool carefully to make sure no breakage or
damage occurred during shipping.
Do not discard the packing material until you have care-
fully inspected and satisfactorily operated the tool.
Remove the dust hood from its position on top of the
motor housing then remove the cardboard from the
cutterhead.
NOTE: All bolts should be inserted from the top. Install
the lock washers and hex nuts from the underside of the
workbench.
Supporting surface where planer is mounted should be
examined carefully after mounting to insure that no move-
ment during use can result. If any tipping or walking is noted,
secure workbench or support surface before beginning
planing operation.
NOTE: Install the dust hood before using this product.
Remove the blue plastic covering the planer table prior
to turning on this product.
The tool is factory set for accurate cutting. After
assembling it, check for accuracy. If shipping has influ-
encedthesettings,refertospecificproceduresexplained
in this manual.
CLAMPING PLANER TO WORKbENCH
See Figure 6.
Iftheplaneristobeusedasaportabletool,itisrecommended
you fasten it permanently to a mounting board that can eas-
ily be clamped to a workbench or other stable surface. The
mounting board should be of sufficient size to avoid tipping
while planer is in use. Any good grade plywood or chipboard
with a 3/4 in. thickness is recommended.
If any parts are damaged or missing, please call
1-866-539-1710 for assistance.
Mark holes on board where planer is to be mounted using
holes in planer base as a template for hole pattern.
Follow last three steps in section Mounting Planer to
WARNING:
Workbench.
If any parts are damaged or missing, do not
operate this tool until the missing parts are
replaced. Failure to heed this warning could result
in serious personal injury.
If lag bolts are used, make sure they are long enough to go
through holes in planer base and material the planer is being
mounted to. If machine bolts are used, make sure bolts are
long enough to go through holes in planer base, the material
being mounted to, and the lock washers and hex nuts.
WARNING:
Do not attempt to modify this tool or create
accessories not recommended for use with this
tool. Any such alteration or modification is misuse
and could result in a hazardous condition leading
to possible serious personal injury.
WARNING:
Do not connect to power supply until assembly
is complete. Failure to comply could result in
accidental starting and possible serious personal
injury.
MOUNTING THE PLANER TO WORKbENCH
If your planer is to be used in a permanent location, it is
recommended you secure it to a workbench or other stable
surface. When mounting the planer to a workbench, holes
should be drilled through the supporting surface of the
workbench.
Fig. 6
14
Download from Www.Somanuals.com. All Manuals Search And Download.
ASSEMbLY
duSt hood
knoBS
INSTALLING HANDWHEEL KNOb
See Figure 7.
Slot
duSt
AdAPtor
Locate the handwheel knob and screw from among
the loose parts. Insert the screw through the hole in the
handwheel and tighten screw securely.
Using the hex head screw, attach the depth adjustment
handwheel securely to the planer.
INSTALLING THE DUST HOOD
See Figure 8.
From the back of the machine, slip the slot on the dust hood
overthetabinsidetheplanerandalignthedusthoodoverthe
holesonthesideoftheplaner. Installthedusthoodknobsby
turning them clockwise. To minimize sawdust accumulation
on your workpiece, attach either a ꢀ-1/ꢀ in. shop vac or a
4 in. dust collection system to the dust hood.
NOTE: The end of a 4 in. hose fits over the dust adaptor and
requires a clamp (not included) to secure.
To open and close the dust hood door, align the arrows on
the side.
NOTE: With the dust hood open, the sawdust is ejected
from the back. With the dust hood closed, the sawdust is
ejected from the adaptor.
dePth
AdjuStment
hAndwheel
to oPen
duSt hood
door
hex heAd
SCrew
ArrowS
hAndwheel
SCrew
knoB
Fig. 7
to CloSe
Fig. 8
15
Download from Www.Somanuals.com. All Manuals Search And Download.
ASSEMbLY
LEVELING THE TAbLE ExTENSIONS
See Figure 9.
The infeed and outfeed table extensions are attached to
the planer. Shipped in a folded, upright position, the table
extensions must be in the down position before planing can
begin. For accurate planing, table extensions must be level
with the planer table.
NOTE: For optimum performance, always check to make
sure the table extensions are level before beginning planing
operations.
StoP
SCrewS
Place a straight edge or level across both the planer table
and table extensions.
If adjustment is necessary, lift table extensions and loosen
lock nuts. Adjust stop screws (one on each side) until
extension table is level with planer table.
Press down on the table extension to ensure the table
extension is properly seated.
Tighten lock nuts securely when adjustments are
complete.
loCk nut
tABle
extenSion
StrAiGht
edGe
tABle
extenSion
PlAner
tABle
Fig. 9
16
Download from Www.Somanuals.com. All Manuals Search And Download.
OPERATION
THICKNESS PLANING
WARNING:
Do not allow familiarity with tools to make you
careless. Remember that a careless fraction of a
second is sufficient to inflict serious injury.
Thicknessplaningsizesworkpiecetodesiredthicknesswhile
creating a smooth, level surface. Thickness of each cut will
depend on type of wood (hardwood versus softwood), width
of workpiece, straightness, dryness, and grain composition.
Whenever working with a new type of wood, make thin test
cuts on a scrap piece of wood first to determine potential
problems with the workpiece.
WARNING:
Always wear safety goggles or safety glasses
with side shields when operating power tools.
Failure to do so could result in objects being
thrown into your eyes resulting in possible seri-
ous injury.
PLANING TIPS
Thickness planers work best if at least one side of the
workpiece has a flat surface. When both sides of a
workpiece are rough, use a surface planer or jointer first
to define the initial flat surface. Plane one side of the
workpiece then flip the workpiece and plane the surface
of the reverse side.
WARNING:
Always plane both sides of a workpiece to reach the
desired thickness. This will leave the workpiece with
uniform moisture to prevent warp during the drying
process.
Do not use any attachments or accessories
not recommended by the manufacturer of this
tool. The use of attachments or accessories not
recommended can result in serious personal
injury.
When one end of the workpiece is thicker than the
opposite end by more than 1/8 in., make several cuts with
the planer starting with light planing cuts first. Remember,
light cuts create a finer finish than heavier cuts.
WARNING:
The use of this planer on materials not listed
may damage the planer and may cause serious
personal injury.
Do not plane a workpiece less than 5/16 in. thick.
Do not plane a workpiece less than 3/4 in. wide.
Do not plane workpiece shorter than 14 in. long as this
will cause kickback.
Do not plane more than one workpiece at a time.
WARNING:
Do not lower the cutterhead assembly lower than
Never plane workpiece with loose knots or
foreign objects. Do not plane workpieces that
are severely bowed, twisted, or knotted. Cutter
blades can dull, chip, or break causing possible
serious personal injury.
5/16 in.
Do not continuously use the planer set at the maximum
depth of cut (1/8 in.) and at full width of cut (13 in.).
Continuous use at maximum cutting capacity will damage
the motor.
Worn cutter blades will affect cutting accuracy. Planing
with dull or nicked cutter blades may produce ridges or
rough workpiece surfaces.
WARNING:
Do not force feed the workpiece through the
machine. Let the planer apply the proper feed
rate.
Gum and pitch on the cutter blades will cause them to
wear prematurely. Using a gum and pitch remover to keep
your cutter blades clean will prolong their wear.
Refer to the Maintenance section of this operator’s
manual for instructions on how to remove and replace
or turn the cutter blades.
APPLICATIONS
You may use this tool for the purpose listed below:
NOTE: Cutter blades are double-edged and can be turned
once to the opposite, unused edge before replacement
is required. Cutter blades must ALWAYS be replaced as
a set.
Planing the surface of a piece of lumber.
17
Download from Www.Somanuals.com. All Manuals Search And Download.
OPERATION
AVOIDING SNIPE
POWER SWITCH
See Figure 10.
Snipes, or depressions made at either end of a workpiece
by cutter blades, can occur when the board is not properly
supported. Although snipe may be barely noticeable, it is
important to keep the workpiece parallel and flat with the
planer table to minimize snipe. Butting workpieces end-
to-end as they are fed through the planer will minimize the
problem, especially for shorter pieces, because it provides
a more stable feed.
Theplanerisequippedwithapowerswitchthathasabuilt-in
locking feature. This feature is intended to prevent unauthor-
ized and possible hazardous use by children and others.
TO TURN THE PLANER ON:
With the switch key inserted into the switch, lift the switch
to turn ON (l).
TO TURN THE PLANER OFF:
For workpieces longer than 48 in., greater care must be
taken to reduce the problem because the additional length
means more of the total weight is unsupported by the planer
table and rollers, causing the shifting weight to work against
keeping the stock flat.
With the switch key inserted into the switch, push the
switch down to turn OFF (O).
TO LOCK THE PLANER:
Place the switch in the OFF (O) position.
To remove snipe from a finished workpiece, cut off the end
of the workpiece where snipe is noticeable.
Remove the switch key from the switch and store in a
secure location.
WARPED WOOD
Little or no warpage is the ideal condition for planing a
workpiece. Simply turn the workpiece over and plane it to
the desired thickness. Otherwise, plane the top first, turn
the workpiece and plane the bottom.
WARNING:
Always remove the switch key when the tool is
not in use and keep it in a safe place. In the event
of a power failure, turn the switch OFF (O) and
remove the key. This action will prevent the tool
from accidentally starting when power returns.
Foraboardthatiscuppedorbowedacrossitswidth,thebest
method is to rip the board lengthwise down the middle and
plane the pieces separately. This method eliminates much
of the waste in planing cupped or bowed workpieces.
The only way to remove the bow from a workpiece that is
cupped or bowed down its length is to use a jointer.
WARNING:
Always make sure the workpiece is not in contact
with the blade before operating the switch to start
the tool. Failure to heed this warning may cause the
workpiece to be kicked back toward the operator
and result in serious personal injury.
Avoid using severely warped wood as it can jam the planer.
If it must be used, rip it in half before planing to help mini-
mize the possibility of jamming. If jamming does occur, turn
the switch off and unplug the planer immediately. Raise the
cutterhead assembly high enough to remove the workpiece
easily. Carefully check to make sure no damage to the tool
has occurred before making the next planing pass.
Always feed the workpiece in the direction of the grain. This
allows the cutter blades to sever the wood fibers instead of
tearing them. Feeding against the grain can also cause the
cutter blades to chip the workpiece.
SwitCh key
oFF
on
Fig. 10
18
Download from Www.Somanuals.com. All Manuals Search And Download.
OPERATION
ADJUSTING THE PLANING DEPTH
See Figure 11.
The depth adjustment handwheel is used to set the amount
of wood being removed in a planing pass. Never make a
planing cut deeper than 1/8 in. for material up to 6 in. wide
or 1/16 in. for material between 6 in. and 13 in. wide.
NOTE: Do not continuously use the planer at the maximum
depth of cut (1/8 in.) as it will damage the motor.
Rotate the depth adjustment handwheel to position the
cutterhead at the desired planing depth. Each full revolution
of the handle will raise or lower the cutterhead 1/16 in.
DEPTH GAUGE
See Figure 12.
Thedepthgaugeindicatestheamountofwoodbeingremoved
in a planing pass. The workpiece must be positioned under
the depth gauge on the front of the planer.
dePth
AdjuStment
hAndwheel
"
8
1
1
4
1
2
3
4
1
1
Never make a planing cut deeper than:
1/8 in. for material up to 6 in. wide
1/16 in. for material 6 in. - 13 in. wide
Do not continuously use the planer at the maximum depth
of cut, 1/8 in., as it will damage the motor.
PLANING
See Figure 13.
Fig. 11
Use scrap wood for your first planing attempt. Once you
haveplanedthewood,checkallmeasurementsforaccuracy.
If measurements are not exact, see Adjustment section for
further instruction.
Before each use of the planer, check for loose fasteners,
fittings, or hardware; be sure the dust hood is securely
mounted; and ensure the blade cutter rotates freely. Lower
the cutterhead assembly to approximately 1 in. above the
planer table surface. Without putting any load on the planer,
test the motor by turning the planer on and allowing it to
reach full speed. If the planer sounds excessively loud or
has excessive vibration, turn off the machine immediately
and check again for any loose hardware, retightening any
you may find.
dePth
GAuGe
WARNING:
To avoid serious personal injury, do not stand
directly in line with the front or rear of the planer.
If an object is thrown from the planer, it will travel
in this direction.
Fig. 1ꢀ
Stand to one side of the planer infeed area.
Turn switch ON ( l ).
Lift the work to the table by grasping the edges of the
board at approximately the middle of the length. Rest the
board end on the feed table and direct the board into the
planer.
NOTE: Boards longer than ꢀ4 in. should have additional
support from free-standing material stands.
19
Download from Www.Somanuals.com. All Manuals Search And Download.
OPERATION
Push slightly on the board and allow the automatic feed
to take the board.
Release the board to allow the automatic feed to function
properly. Do not push or pull on the workpiece.
Move to one side at the rear of the planer and receive
the planed lumber by grasping it in the same manner as
it was fed. Do not grasp any portion of the board which
has not gone past the outfeed area of the table.
REPLANING USING REPEAT-A-CUT™
See Figure 14.
The planer has a replane feature using preset markers for
repetitive planing. The Repeat-A-Cut™ allows you to plane
material at a set measurement. The maximum depth of the
replane indicator is 1-3/4 in.
Raise cutterhead assembly to a height greater than
1-3/4 in.
Move the replane indicator to the desired height.
Lower the cutterhead assembly until it stops.
Stand to one side of the planer infeed area.
Fig. 13
Turn switch ON ( l ).
Plane the workpiece (see Depth Gauge on page 19 for
CutterheAd
ASSemBly
maximum depth of cut).
Repeat above steps until desired planing depth.
rePlAne
indiCAtor
Fig. 14
ꢀ0
Download from Www.Somanuals.com. All Manuals Search And Download.
ADJUSTMENTS
thiCkneSS
SCAle
WARNING:
Before performing any adjustment, make sure the
tool is unplugged from the power supply and the
switch is in the OFF position. Failure to heed this
warning could result in serious personal injury.
SCAle
indiCAtor
SCrewS
SCAle
indiCAtor
THICKNESS SCALE ADJUSTMENT
See Figure 15.
Located on the right front of the planer, the thickness scale
shows the depth of the finished workpiece. Inaccurate cuts
can be prevented by routinely checking the alignment of
the thickness scale.
Table extensions must be level with planer table.
Plane a scrap piece of wood then measure the depth of
the finished piece.
If properly adjusted, the depth of the finished piece should
be the same as indicated on the thickness scale.
Fig. 15
If out of adjustment, loosen the scale indicator screws
holding the scale indicator and adjust the thickness
indicator to the correct setting.
Retighten screws securely.
bLADE ADJUSTMENT
See Figure 16.
Tiny nicks may appear on the blades as a result of picking
up sand or other particles on a workpiece and then run-
ning the workpiece through the planer. Slight adjustments
can be made to one or both blades to offset such planing
imperfections.
Unplug the planer.
Lower the cutterhead assembly.
Remove the dust hood knobs holding the dust hood in
place; remove hood and set aside.
BlAde
loCkinG
SCrewS
BlAde
WARNING:
To avoid injury, NEVER rotate the cutterhead by
hand.
Fig. 16
Using the hex key, loosen the blade locking screws that
secure the blade in the cutterhead.
Push the notched end of the cutter blade on either the
left or right side to shift the blade as desired. The blade
can be shifted up to 3/64 in.
Retighten the blade locking screws securely.
Replace the dust hood and reinstall dust hood knobs to
secure.
ꢀ1
Download from Www.Somanuals.com. All Manuals Search And Download.
ADJUSTMENTS
REPEAT-A-CUT™
See Figure 17.
Plane a scrap piece of wood and measure the depth of the
finished piece. If an adjustment is needed:
Unplug the planer.
Pull the replane indicator straight out to remove.
Using the hex key provided, remove the hex head screw
from the depth adjustment handwheel. Remove the
handwheel.
Remove the screws on the top and right side panel of the
planer. Carefully lift and pull the side panel cover off.
Lower the cutterhead assembly until it stops against the
stop screw.
rePlAne
indiCAtor
Using an accurate ruler or a scrap piece of wood, check
the measurement against the replane indicator setting.
If adjustment is necessary, use a wrench to loosen
the lock nut and adjust the stop screw to the correct
height.
Once the adjustment is made, retighten the lock nut and
stop screw securely.
Replace the top and side panel, and secure using the set
screw.
Replace the handwheel and hex head screw.
loCk nut
Replace the replane indicator.
StoP SCrew
Fig. 17
ꢀꢀ
Download from Www.Somanuals.com. All Manuals Search And Download.
MAINTENANCE
CLEANING
WARNING:
When servicing, use only identical replacement
parts. Use of any other part may create a hazard
or cause product damage.
Sawdust buildup and other debris can cause the tool to
plane inaccurately. Periodic cleaning and waxing is needed
for accurate, precision planing.
Do not allow sawdust to accumulate on the planer. Clean
the dust hood after each use.
WARNING:
DANGER:
Rotating blades under dust hood. In order to
avoid personal injury, keep fingers away.
Always wear safety goggles or safety glasses with
side shields during power tool operation or when
blowing dust. If operation is dusty, also wear a
dust mask.
Moving parts should be cleaned regularly with penetrating
oil and lubricated with a light coating of medium-weight
machine oil.
GENERAL MAINTENANCE
Avoid using solvents when cleaning plastic parts. Most
plastics are susceptible to damage from various types of
commercial solvents and may be damaged by their use. Use
clean cloths to remove dirt, carbon dust, etc.
Paste wax should be applied to the planing table surface to
ease the movement of workpieces across it, but be careful
not to use so much that it will be absorbed into the wood
and interfere with staining.
Check feed rollers after each use for resin buildup, because
feed rollers must be clean to be effective. If buildup occurs,
use a mild, nonflammable tar and pitch remover.
WARNING:
Do not at any time let brake fluids, gasoline,
petroleum-based products, penetrating oils, etc.,
come in contact with plastic parts. They contain
chemicals that can damage, weaken, or destroy
plastic.
bLADE / TOOL STORAGE
See figure 18.
For your convenience, an extra set of blades can be
stored under the outfeed table extension in the blade / tool
storage.
LUbRICATION
All of the bearings in this tool are lubricated with a sufficient
amount of high grade lubricant for the life of the unit under
normal operating conditions. Therefore, no further lubrica-
tion is required.
Dispose of used blades properly. Wrap blades in tape before
disposal to avoid accidental injury.
WARNING:
To ensure safety and reliability, all repairs should
be performed by a qualified service technician
at an authorized service center to avoid risk of
personal injury.
MOTOR/ELECTRICAL
The universal motor is easy to maintain but must be kept
clean. Do not allow water, oil, or sawdust to accumulate on
or in it. The sealed bearings are permanently lubricated and
need no further attention.
BlAde / tool
StorAGe
Fig. 18
ꢀ3
Download from Www.Somanuals.com. All Manuals Search And Download.
MAINTENANCE
CORD STORAGE
See Figure 19.
For convenience, your planer comes equipped with cord
storage.Whennotinuse,thepowercordshouldbewrapped
around the planer.
CAUTION:
Check extension cords before each use. If
damaged, replace immediately. Never use tool with
a damaged cord since touching the damaged area
could cause electrical shock resulting in serious
injury.
bRUSH REPLACEMENT
See Figure 20.
Externally accessible brush assemblies are located at the
right front and the left rear of the planer. These brushes
should be inspected every 10 to 15 operating hours for wear.
Replacebothbrusheswheneitherbrushhaslessthan1/4 in.
of carbon remaining.
Cord
StorAGe
Fig. 19
NOTE: The dust hood may be removed for easier access
when removing the rear brush cap.
Unplug planer and remove the switch key.
Using a flat-head screwdriver, unscrew the brush cap.
The brush assembly is spring-loaded and will pop out
when you remove the cap.
Remove the brush assembly (brush and spring) and
inspect for wear. If less than 1/4 in. of carbon remains
on brush, replace both brush assemblies. Never replace
one side without replacing the other.
BruSh
BruSh
CAP
Install new brush assembly, if required, or reinstall old
brush assembly.
Replace cap and tighten to secure.
Fig. ꢀ0
ꢀ4
Download from Www.Somanuals.com. All Manuals Search And Download.
MAINTENANCE
CutterheAd
loCk
bLADE REPLACEMENT
See Figures 21 - 23.
The planer is equipped with replaceable/disposable double-
edged cutter blades attached to a rotating cutterhead. Worn
cutter blades will affect cutting accuracy and may produce
ridges on the workpiece.
Unplug the planer.
Lower the cutterhead assembly.
From the back of the planer, remove the two dust hood
knobs holding the dust hood in place.
Remove the dust hood.
driVe
Belt
NOTE: The cutterhead lock will engage when the head
is rotated. Do not operate thickness planer without the
dust hood in place or the planer will be damaged.
Fig. ꢀ1
If necessary, rotate the cutterhead until it locks.
NOTE: Rotating the cutterhead is accomplished from
beneath the cutterhead assembly. Using the planer table
as a mirror, touch the threaded spindle where it attaches
to the planer table. Carefully move your fingers up until
you touch the drive belt. Turn the drive belt with your
fingers until the cutterhead locks in place.
hex key
to
tiGhten
to
looSen
Carefully loosen, but do not remove, the blade locking
screws.
Using the magnetic blade tool, remove the blade by
placing the blade tool on the blade, lifting slightly, then
pulling the blade straight out.
If you are changing to the second side of the blade, rotate
the blade “end for end” keeping the same flat side down.
This correctly positions the blade for reinstallation.
Using the magnetic blade tool, push the installed blade
in firmly. Check that the blade edge is parallel to the
cutterhead slot.
BlAde loCkinG
SCrewS
Securely retighten the blade locking screws.
To rotate the cutterhead to the next blade, hold down on
the red cutterhead lock and rotate the cutterhead 1ꢀ0°
as shown in figure ꢀ1.
Fig. ꢀꢀ
Release the cutterhead lock and continue to rotate the
cutterhead until it locks in place. This correctly positions
the blade for removal.
Repeat the above steps for each blade.
Replace the dust hood.
mAGnetiC
BlAde tool
BlAde
Fig. ꢀ3
ꢀ5
Download from Www.Somanuals.com. All Manuals Search And Download.
TROUbLESHOOTING
PRObLEM
POSSIbLE CAUSE
SOLUTION
Snipe (depressions at ends of
workpiece)
Dull cutter blades
Replace or turn cutter blades.
Incorrect butted stock
Butt pieces end-to-end as they are
fed into planer.
Unit not securely mounted
Tighten lag bolts.
Torn grain
Too deep a blade setting
Workpiece being fed against grain
Dull cutter blades
Reduce depth of cut.
Feed other end of board first.
Replace or turn cutter blades.
Fuzzy/rough grain
High wood moisture content
Dull cutter blades
Dry wood before planing.
Replace or turn cutter blades.
Reduce depth of cut.
Too deep a blade setting
Incorrect feeding speed
Check for adequate power supply.
Check cord and plug for damage.
Check condition of motor brushes.
Uneven depth of cut
Cutterhead assembly not level with
planer surface
Adjust elevation nuts.
Unstable roller spring pressure
Have service performed by an
authorized service center.
Feed roller worn unevenly
Have service performed by an
authorized service center.
Board thickness does not match
depth scale indicator
Depth scale incorrectly set
Dirty planing table
Adjust depth scale.
Clean and wax planing table.
Cutterhead height difficult to adjust
Dirty spindle
Worn chain
Clean and lubricate spindle.
Have service performed by an
authorized service center.
Will not start
Not plugged in
Blown circuit
Check power source.
Replace fuse, reset breaker, or call
electrician.
Motor failure
Loose wire
Have service performed by an
authorized service center.
Have service performed by an
authorized service center.
ON/OFF switch malfunction
Motor is overloaded
Have service performed by an
authorized service center.
Push reset button.
Interrupted operation
Unit overloaded
Reduce load.
Circuit overloaded
Operate on circuit separate from
other appliances or motors or con-
nect to circuit with adequate amp
rating.
ꢀ6
Download from Www.Somanuals.com. All Manuals Search And Download.
WARRANTY
RIDGID® HAND HELD AND STATIONARY POWER TOOL
3 YEAR LIMITED SERVICE WARRANTY
Proof of purchase must be presented when requesting
warranty service.
WHAT IS NOT COVERED
This warranty applies only to the original purchaser at
retail and may not be transferred. This warranty only covers
defects arising under normal usage and does not cover any
malfunction, failure or defect resulting from misuse, abuse,
neglect, alteration, modification or repair by other than
an authorized service center for RIDGID® branded hand
held and stationary power tools. Consumable accessories
provided with the tool such as, but not limited to, blades,
bits and sand paper are not covered.
Limited to RIDGID® hand held and stationary power tools
purchased ꢀ/1/04 and after. This product is manufactured
by One World Technologies, Inc. The trademark is licensed
from RIDGID®, Inc. All warranty communications should be
directed to One World Technologies, Inc., attn: RIDGID®
Hand Held and Stationary Power Tool Technical Service at
(toll free) 1-866-539-1710.
90-DAY SATISFACTION GUARANTEE POLICY
RIDGID®, INC. AND ONE WORLD TECHNOLOGIES, INC.
MAKENOWARRANTIES,REPRESENTATIONSORPROM-
ISES AS TO THE QUALITY OR PERFORMANCE OF ITS
POWER TOOLS OTHER THAN THOSE SPECIFICALLY
STATED IN THIS WARRANTY.
During the first 90 days after the date of purchase, if you are
dissatisfied with the performance of this RIDGID® Hand Held
and Stationary Power Tool for any reason you may return
the tool to the dealer from which it was purchased for a full
refund or exchange. To receive a replacement tool you must
present proof of purchase and return all original equipment
packaged with the original product. The replacement tool
will be covered by the limited warranty for the balance of
the 3 YEAR service warranty period.
ADDITIONAL LIMITATIONS
Totheextentpermittedbyapplicablelaw, allimpliedwarran-
ties,includingwarrantiesofMERCHANTABILITYorFITNESS
FORAPARTICULARPURPOSE,aredisclaimed.Anyimplied
warranties, including warranties of merchantability or fitness
for a particular purpose, that cannot be disclaimed under
statelawarelimitedtothreeyearsfromthedateofpurchase.
One World Technologies, Inc. and RIDGID®, Inc. are not
responsible for direct, indirect, incidental or consequential
damages. Some states do not allow limitations on how long
an implied warranty lasts and/or do not allow the exclusion
or limitation of incidental or consequential damages, so the
above limitations may not apply to you. This warranty gives
you specific legal rights, and you may also have other rights
which vary from state to state.
WHAT IS COVERED UNDER THE 3 YEAR
LIMITED SERVICE WARRANTY
This warranty on RIDGID® Hand Held and Stationary Power
Toolscoversalldefectsinworkmanshipormaterialsandnor-
mal wear items such as brushes, chucks, motors, switches,
cords, gears and even cordless batteries in this RIDGID®
tool for three years following the purchase date of the tool.
Warranties for other RIDGID® products may vary.
HOW TO ObTAIN SERVICE
To obtain service for this RIDGID® tool you must return it;
freight prepaid, or take it in to an authorized service center
for RIDGID® branded hand held and stationary power tools.
You may obtain the location of the authorized service center
nearest you by calling (toll free) 1-866-539-1710 or by log-
requesting warranty service, you must present the original
dated sales receipt. The authorized service center will
repair any faulty workmanship, and either repair or replace
any part covered under the warranty, at our option, at no
charge to you.
One World Technologies, Inc.
P.O. Box 35, Hwy. 8
Pickens, SC ꢀ9671
ꢀ7
Download from Www.Somanuals.com. All Manuals Search And Download.
OPERATOR’S MANUAL
13 in. THICKNESS PLANER
R4330
CUSTOMER SERVICE INFORMATION
For parts or service, contact your nearest RIDGID authorized service
center.Besuretoprovideallrelevantinformationwhenyoucallorvisit.
For the location of the authorized service center nearest you, please
Themodelnumberofthistoolisfoundonaplateattachedtothemotor
housing. Pleaserecordtheserialnumberinthespaceprovidedbelow.
When ordering repair parts, always give the following information:
R4330
Model No.
Serial No.
983000-555
9-ꢀ5-07 (REV:01)
Download from Www.Somanuals.com. All Manuals Search And Download.
|