RTD215 EN 6/2/07 3:36 PM Page 3
User manual
Guide de l’utilisateur
Manual de usuario
RTD215
It is important to read this instruction book prior to using your new product for the first time.
Nous vous recommandons de lire ce manuel d’instructions avant d’utiliser votre nouveau produit pour la première fois.
Es importante leer este manual antes de usar por vez primera su euipo.
Download from Www.Somanuals.com. All Manuals Search And Download.
RTD215 EN[E] 16/5/07 2:20 PM Page 5
For Your Safety
Service Information
The AC power plug is
This product should be serviced only by those
specially trained in appropriate servicing
techniques. For instructions on how to obtain
service, refer to the warranty included in this
Guide. RFC: CTM-9800723-KS5
polarized (one blade is
wider than the other) and
only fits into AC power
outlets one way. If the plug
EN
won’t go into the outlet
completely, turn the plug over and try to insert it
the other way. If it still won’t fit, contact a
qualified electrician to change the outlet, or use
a different one. Do not attempt to bypass this
safety feature.
Main plug is used as the disconnect device, it
shall remain operable and should not be
obstructed during intended use. To be completely
disconnected the apparatus from supply mains,
the main plug of the apparatus shall be
disconnected from the mains socket outlet
completely.
CAUTION:
• To prevent electric shock, match wide blade of
plug to wide slot, fully insert.
Caution!
Invisible laser radiation when open. Avoid
exposure to beam. Class 1 laser product. This
system must be opened only by qualified
technicians to prevent accidents caused by the
laser beam.
Note:
This DVD player is designed and manufactured to
respond to the Region Management Information.
If the Region number of a DVD disc does not
correspond to the Region number of this DVD
player, this player cannot play the disc. The
Region number for this DVD player is
Region 1.
DVD copy protection
In accordance with the DVD standard, your DVD
player is equipped with a Copy Protection system,
which can be switched on and off by the DVD
disc itself, in order to make any recording of the
relevant DVD disc onto a videotape of very poor
picture quality, or even impossible. This product
incorporates copyright protection technology
that is protected by method claims of certain
U.S. patents and other intellectual property rights
owned by Macrovision Corporation and other
rights owners. Use of this copyright protection
technology must be authorized by Macrovision
Corporation, and is intended for home use only
unless otherwise authorized by Macrovision
Corporation. Reverse engineering or disassembly
is prohibited.
Download from Www.Somanuals.com. All Manuals Search And Download.
RTD215 EN 6/2/07 3:36 PM Page 6
FCC Information
Important Battery Information
• Do not mix different types of batteries or new
CAUTION
THIS PRODUCT UTILIZES A LASER. USE OF
CONTROLS OR ADJUSTMENTS OR
PERFORMANCE OF PROCEDURES OTHER THAN
THOSE SPECIFIED HEREIN MAY RESULT IN
HAZARDOUS RADIATION EXPOSURE. DO NOT
OPEN COVERS AND DO NOT REPAIR YOURSELF.
REFER SERVICING TO QUALIFIED PERSONNEL.
and old batteries. Do not use rechargeable
batteries.
EN
• In order to avoid any risk of explosion, observe
the polarities indicated inside the battery
compartment. Replace only with the type of
batteries specified. Do not dispose of them in a
fire or recharge them.
This Class B digital apparatus complies with
Canadian ICES-003.
Cet appareil numérique de la class B est
conforme à la norme du NMB-003 du Canada
• If you are not using the remote control for a
long period of time, remove the batteries.
Please respect the environment and
prevailing regulations. Before you
dispose of batteries or accumulators,
ask your dealer whether they are
subject to special recycling and if they
will accept them for disposal.
WARNING
To reduce the risk of fire or electric shock, do
not expose this product to rain or moisture. No
objects filled with liquids, such as vases, should
be placed on the apparatus.
Illustrations contained in this document are for
representation only.
CAUTION
RISK OF ELECTRIC SHOCK
DO NOT OPEN
THE LIGHTNING
FLASH AND ARROW-
HEAD WITHIN THE
CAUTION: TO REDUCE THE THE EXCLAMATION
RISK OF ELECTRIC SHOCK, POINT WITHIN THE
DO NOT REMOVE COVER TRIANGLE IS
A
TRIANGLE IS
A
WARNING
SIGN
ALERTING YOU OF
M P O R TA N T
(OR BACK). NO USER-
SERVICEABLE PARTS IN-
SIDE. REFER SERVICING
TO QUALIFIED SERVICE
PERSONNEL.
WARNING SIGN
ALERTING YOU OF
" D A N G E R O U S
VOLTAGE" INSIDE
THE PRODUCT.
I
I NSTRUCTI ONS
ACCOMPANYING
THE PRODUCT.
SEE MARKING ON BOTTOM / BACK OF PRODUCT
WARNING:TO PREVENT FIRE OR ELECTRICAL
DO NOT EXPOSETHIS PRODUCT
SHOCK HAZARD,
TO RAIN OR MOISTURE.
Download from Www.Somanuals.com. All Manuals Search And Download.
RTD215 EN 6/2/07 3:36 PM Page 7
Important Safety Instructions
PLEASE READ AND SAVE FOR FUTURE
REFERENCE
Some of the following information may not apply
to your particular product; however, as with any
electronic product, precautions should be
observed during handling and use.
• Unplug this apparatus during lightning storms
or when unused for long periods of time.
• Refer all servicing to qualified service
personnel. Servicing is required when the
apparatus has been damaged in any way, such
as power-supply cord or plug is damaged, liquid
has been spilled or objects have fallen into the
apparatus, the apparatus has been exposed to
rain or moisture, does not operate normally, or
has been dropped.
EN
• Read these instructions.
• Keep these instructions.
• Heed all warnings.
• Follow all instructions.
• Do not use this apparatus near water.
• Clean only with dry cloth.
• Do not block any ventilation openings. Install in
accordance with the manufacturer’s
instructions.
• Do not install near any heat sources such as
radiators,heat registers, stoves, or other
apparatus (including amplifiers) that produce
heat.
ADDITIONAL SAFETY INFORMATION
• Apparatus shall not be exposed to dripping or
splashing and no objects filled with liquids,
such as vases, shall be placed on the apparatus.
• Always leave sufficient space around the
product for ventilation. Do not place product in
or on a bed, rug, in a bookcase or cabinet that
may prevent air flow through vent openings.
• Do not place lighted candles, cigarettes, cigars,
etc. on the product.
• Do not defeat the safety purpose of the
polarized or grounding-type plug. A polarized
plug has two blades with one wider than the
other. A grounding type plug has two blades
and a third grounding prong. The wide blade
or the third prong is provided for your safety. If
the provided plug does not fit into your outlet,
consult an electrician for replacement of the
obsolete outlet.
• Protect the power cord from being walked on
or pinched particularly at plugs, convenience
receptacles, and the point where they exit from
the apparatus.
• Connect power cord only to AC power source
as marked on the product.
• Care should be taken so that objects do not fall
into the product.
• Do not attempt to disassemble the cabinet. This
product does not contain customer serviceable
components.
IF YOUR PRODUCT OPERATES ON BATTERIES,
adhere to the following precautions:
A. Any battery may leak electrolyte if mixed with
a different battery type, if inserted incorrectly,
or if all batteries are not replaced at the same
time.
B. Any battery may leak electrolyte or explode if
disposed of in fire or an attempt is made to
charge a battery not intended to be recharged.
C. Discard leaky batteries immediately. Leaking
batteries can cause skin burns or other
personal injury. When discarding batteries, be
sure to dispose of them in the proper manner,
according to your state/provincial and local
regulations.
• Only use attachments/accessories specified by
the manufacturer.
• Use only with the cart, stand, tripod, bracket,
or table specified by the manufacturer, or sold
with the apparatus. When a cart is used, use
caution when moving the cart/apparatus
combination to avoid injury from tip-over.
]
Portable Cart Warning
Download from Www.Somanuals.com. All Manuals Search And Download.
RTD215 EN 6/2/07 3:36 PM Page 8
Table of Contents
Connections and Setup . . . . . . . . . . .1
USB Device . . . . . . . . . . . . . . . . . . . . . .16
Connecting/Disconnecting USB devices
to the Main Unit
Connecting to audiovisual equipments . . . . . .2
Connecting the speakers . . . . . . . . . . . . . . . . . .3
EN
Positioning speakers . . . . . . . . . . . . . . . . . . . . .4
USB Device Playback Features
Front speaker placement.
Better surround placement . . . . . . . . . . . . . . .5
Test tone/Channel balance
CD Ripping . . . . . . . . . . . . . . . . . . . . . .17
An overview
Ripping CD to USB device
Start Ripping CD
File Names of Ripped Files
Deleting Files
Overview of Controls . . . . . . . . . . . . .6
Front panel controls
Remote control
Remote control functions in TUNER mode . . .7
Using the remote to Navigate through
On Screen Menus . . . . . . . . . . . . . . . . . . . . . . . .8
The Setup Menu . . . . . . . . . . . . . . . .18
General Setup
Password
Playing Discs – Basic Functions . . .8
Compatible discs/formats
Regional coding
Operating the DVD receiver
Basic Playback Operations . . . . . . . . . . . . . . . .9
Types of Menus
Rating . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .19
Slide Time
Default
Display Setup
Display Type
Dark Level
Video . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .20
Speaker Setup
Night Mode
Distance
The Info Menu . . . . . . . . . . . . . . . . . .10
Using the Info menu
Title/chapter (DVD)/track
(audio CD and VCD)
Test Tone
Time Display . . . . . . . . . . . . . . . . . . . . . . . . . . .11
Audio (DVD,VCD)/Subtitles (DVD)/
Camera Angle (DVD) . . . . . . . . . . . . . . . . . . .12
Play mode
Creating a Program list for Play Mode
Bookmark/Sleep/PBC/Introscan(CD) . . . . . . . .13
Lanugage Setup . . . . . . . . . . . . . . . . . . . . . . . .21
Player Menu
Audio
Subtitles
Disc Menu
Additional Information . . . . . . . . .22
Troubleshooting
Precautions . . . . . . . . . . . . . . . . . . . . . . . . . . . .23
Compatible Formats . . . . . . . . . . . . . . . . . . . . .24
Sound Enhancement Systems . . . . . . . . . . . . .25
Technical Specifications . . . . . . . . . . . . . . . . . .26
Mp3/WMA Files and jpeg Files . .14
Playing mp3/WMA Files or displaying
jpeg files
Radio . . . . . . . . . . . . . . . . . . . . . . . . . . . .15
Manual Tuning
Storing radio stations
Limited Warranty . . . . . . . . . . . . . . .27
Download from Www.Somanuals.com. All Manuals Search And Download.
RTD215 EN 6/2/07 3:36 PM Page 9
Connections and Setup
Accessories provided
EN
+
-
+
-
RCR 192 AD1
Remote control and
2 AAA batteries
Left and right
Surround
Speakers
Subwoofer
Center speaker
Left and right
front speakers
Composite
Video Cable
One external AM loop
antenna
One Pig-Tail
antenna wire
Things to consider before you connect
• The humidity of the room should not exceed
75%. If you have to use the unit outdoors, do
not expose it to rain or splashing water. The
apparatus should not be exposed to dripping
or splashing and no objects filled with liquids,
such as vases, should be placed on
• Ensure that the mains supply in your house
complies with that indicated on the
identification sticker located on the back of
your unit.
• Install your unit horizontally, away from any
source of heat (fireplace) or appliances
creating strong magnetic or electric fields. The
components of this unit are sensitive to heat.
The maximum ambient temperature should
not exceed 35°C/95°F.
• Leave enough space around the unit to allow
adequate ventilation: 10 cm/4 inches on either
side and above the top, and 5 cm/2 inches at
the rear.
the apparatus.
• Moving the unit from a cold place to a warm
one can cause condensation on some
components inside the unit. Let the
condensation disappear on its own before
turning the unit on again.
• Before moving the unit, make sure the disc
tray is empty.
• Where the mains plug or an appliance coupler
is used as a disconnect device, the disconnect
device shall remain readily operable.
• Other important use and cleaning information
at the end of the booklet.
1
Download from Www.Somanuals.com. All Manuals Search And Download.
RTD215 EN 6/2/07 3:36 PM Page 10
Connections and Setup
from the receiver to the screen). The audio jacks
are IN jacks, which need to be connected to OUT
jacks on the component you are connecting to, so
the sound from the component comes into the
receiver (and out through the speakers).
Connecting the antennas
EN
FM 75Ω
White
Antenna
Video cables
Composite video cable
(included)
GND
The basic Video jack (color-
coded yellow) is also referred
to as composite video.
The AM and FM antennas connect to the AM and
FM terminals on the system’s back panel. They
must be hooked up in order to receive clear
reception.
Component video cables (Pr,
Pb, Y) (not included)
The Y, Pb, Pr jacks provide
optimum picture quality by
separating the video signal into
three parts. To ensure
maximum picture quality, use three video-grade
cables for the connection. You can also buy
bundled component video cables that are color-
coded to match the Y, Pb, Pr inputs (green, blue
and red).
AM Loop Antenna and FM Indoor
Antenna
1. Uncoil the AM Antenna wire.
2. Press down on the Antennas tab to open the
terminal.
3. Make sure the white wire on the AM loop
antenna is inserted into the AM loop terminal
and the other wire is inserted into the ground
loop terminal.
Audio cables (not included)
AUDIO IN L (left) and AUDIO
IN R (right)
Connecting to audiovisual equipment
These jacks and cables are
often color-coded (red=right
audio, white=left audio).
VIDEO OUT
Pr
AUDIO IN
Pb
L
Notes:
• If your television is a high definition
television, use the unit's progressive scan
output to get the highest possible video
resolution. Set the Progressive Scan option
in the Video menu to On. See page 20.
• If one of the devices is not working, check
that all the cables have been inserted
properly into the jacks.
• If your component has only one input for
audio (mono), connect it to the left (white
L/Mono) audio jack on the TV and don’t
connect the right audio part of the cable.
VIDEO
Y
R
COMPONENT VIDEO
AUX
(REGULAR AND PROG SCAN)
The jacks on the back of your receiver (shown
above) and the cables shown below are used to
connect to other components.
The video jacks are OUT jacks, which need to be
connected to IN jacks on the TV or monitor
you’re connecting to (so the video content goes
2
Download from Www.Somanuals.com. All Manuals Search And Download.
RTD215 EN 6/2/07 3:36 PM Page 11
Connecting the speakers
Note: When connecting the speakers,
make sure the polarities (“+” speaker wire to
“+” on the receiver. For example, red wire to
red terminal on the receiver) of speaker
wires and terminals match. If the cords are
reversed, the sound will be distorted. Do not
let the speaker wires touch each other, it will
damage the speaker.
Speaker wires are color-coded to match the
terminals. Connect the speaker wire from the
back of each speaker to the corresponding color
terminal at the back of the unit. Press down the
tab to open the terminal and insert the wire.
Release the tab to lock wire in the terminal.
EN
Front Speakers
Center Speaker
Right
Left
Green/Grey
or Black Striped
Purple/Grey or
Black Striped
Subwoofer
SPEAKERS
SR
SL
SUB
3
CEN
FR
FL
4
4
Right
Left
Rear Speakers
(Surround Sound)
3
Download from Www.Somanuals.com. All Manuals Search And Download.
RTD215 EN 6/2/07 3:36 PM Page 12
Connections and Setup
Positioning speakers
Front speaker placement
For best results, follow the speaker placement
below.
3
EN
1
2
1
Alignment
Align the center speaker evenly with (A) or
slightly behind (B) (the left and right speakers),
but not ahead of them.
4
3
Courtesy Dolby Laboratories
1. Left, Right (Front Speakers)
Front speakers carry primarily music and sound
effects.
Angle
2. Center
Place the left and right speakers to form a
45-degree angle with your favorite viewing
position to duplicate the soundtrack mixer’s
perspective.
In surround mode, the center speaker carries
most of the dialog as well as music and effects.
It should be set between the left and right
speakers.
Height
3. Surround (Rear Speakers)
The three front speakers should be as close as
possible to the same height. This often requires
placing the center speaker directly on top (A) or
beneath (B) the TV set.
The surround speakers’ overall sound balance
should be as close as possible to the front
speakers. Proper placement is vital to establish
an evenly distributed sound field.
4. Subwoofer
A
B
A subwoofer is designed to reproduce powerful
low bass effects (explosions, the rumble of
spaceships, etc.).
Note: Front, Center speakers provided with
this unit are magnetically shielded to protect
your TV set. It is not recommended to place
the surround speakers and subwoofer near the
TV set.
4
Download from Www.Somanuals.com. All Manuals Search And Download.
RTD215 EN 6/2/07 3:36 PM Page 13
Better surround placement
Location
If possible, place surround speakers to either side
of the listening area, not behind it.
No adjacent walls
Surround speakers can go on stands facing each
other to approximate sidewall mounting (A), or
to the sides or rear of the viewing area, aimed
upwards; they can go right on the floor, or
preferably, a few feet off the floor such as on end
tables (B).
EN
Height
If space permits, install surround speakers 2-3 feet
above viewers. This helps to minimize localization
effects.
Aiming
Aim surround speakers straight across the room,
not down at viewers, to help create a more open,
spacious surround sound field.
Test tone/Channel balance
Channel balance
Your receiver is equipped with a test signal
generator for balancing the channels. As the
signal “travels” from channel to channel, adjust
the level controls until each channel plays at the
same loudness level (see page 20).
Level adjustment and surround channel
level expectation
Alternative Surround Placement
Rear wall
Even though you adjust the surround channel to
be as loud as the others on the test signal, on
actual program material the surround channel is
usually much lower than the front. Don’t re-
adjust the surround level; program producers use
surround for subtle atmospherics and ambience,
and only rarely for special effects.
If rear wall mounting is the only choice, aim the
speakers at each other (A), towards the front (B)
or towards the sidewalls (C, D). Experiment with
placement until sounds seem to surround you,
rather than come from behind you.
5
Download from Www.Somanuals.com. All Manuals Search And Download.
RTD215 EN 6/2/07 5:24 PM Page 14
Overview of Controls
Front panel controls
EN
Starts/pause
playing a disc.
Adjusts the
volume.
Switches the unit
on and off.
Selects the input
source.
Toggles between
different
subwoofer
Opens and closes
the disc tray.
output levels
among
soft/balance/
strong/powerful.
Stops disc
playback.
Connects USB
devices for
playing music
and photos.
Remote Control
Use the direction buttons to navigate through
the menus. Press the OK button on the remote
control to confirm your selection.
TITLE - Accesses the disc menu for DVD disc.
DISC MENU - Accesses the disc menu during
playback. Turn PBC on/off for VCD disc.
OK - Confirm your selection.
Remote control functions in DVD mode
MUTE - Mutes and restores the sound.
SETUP - Enter Setup menu.
ON•OFF - Switches the unit on and off.
DVD - Selects the DVD mode.
RETURN - In DVD mode, returns to the
previous menu.
TUNER - Selects the TUNER and selects between
FM/AM.
VOL +/- Adjusts the sound volume.
USB - Selects the USB.
AUX - Selects the AUX.
0-9 - Number entry.
CH +/- Directly accesses the next or previous
chapter (DVD) or track (CD).
REV - Starts reverse accelerated play or reverse
slow motion when playback is paused.
CLEAR - Quit the current setting manually from
the TV screen without saving change or delete
files on the USB device.
PLAY - Starts playing a disc.
INFO - Accesses the Info menu.
6
Download from Www.Somanuals.com. All Manuals Search And Download.
RTD215 EN 6/2/07 3:36 PM Page 15
PAUSE - Freeze frame, frame advance or slow
motion.
EN
AUDIO - Accesses the audio function.
ANGLE - Accesses the camera angle function for
DVD disc.
ZOOM - Accesses the Zoom function.
SUBTITLE - Selects the subtitle languages or turns
subtitle off (if available).
MEMORY - Stores station in tuner mode.
SLEEP - Enters sleep mode and selects sleep time.
SUBWOOFER - Selects among subwoofer output
levels among soft/balance/strong/powerful.
RANDOM - Turns on/off random playback for
CDDA/MP3/WMA/jpeg disc.
REPEAT - Accesses the repeat function.
EQ. LEVEL - Toggles channels for different
channel level settings. Adjusts the value using
VOL +/-.
SURROUND - Changes the Surround sound
setting.
Remote control functions in Tuner mode
TUNER - Selects the TUNER and switch between
FM/AM.
VOL+/- Adjusts the sound volume.
MUTE - Mutes and Restores the sound.
TUNER +/- Tunes up and down the radio
RCR 192 AD1
frequencies.
FWD - Starts forward accelerated play or forward
slow motion when playback is paused. Moves
forward one frame at a time after pressing PAUSE
twice.
MEMORY - Stores a station.
CH+/- Selects programmed stations.
AUDIO - Selects between Stereo and Mono mode
for Tuner (FM).
REC - Accesses or quits the CD Ripping menu.
STOP - Stops playback. Press and hold to open
the disc tray.
7
Download from Www.Somanuals.com. All Manuals Search And Download.
RTD215 EN 6/2/07 3:36 PM Page 16
Overview of Controls
Using the remote to Navigate
through On-Screen Menus
No matter what on-screen display you’re using
(the unit's menu, the Info Display that appears
during playback, or a disc’s menu), you’ll use the
same buttons on the remote control to navigate
through the on-screen display; the four arrow
buttons and the OK button.
Notes:
•
•
Sleep function is not available in AUX/TUNER
mode.
Insert 2 "AAA"("UM-4"/"R03") batteries to
the remote control prior to use.
EN
Use the arrow buttons on the remote to move
through on-screen menus in the direction of the
arrow button (to move right, press the right
arrow button, etc.). The arrow buttons are used
to highlight an option. Once highlighted, press
the OK button to select the option that is
highlighted.
Playing Discs - Basic Functions
Compatible discs
Operating the DVD receiver
1. Turn on your television set.
•
DVD, DVD-R,DVD-RW, DVD+R, DVD+RW
•
CD, CD-R, CD-RW
2. Press ON•OFF on the remote or ON/STANDBY
located on the unit’s front panel. Press DVD on
the remote control.
Compatible formats
•
DVD, VCD (Video Compact Disc), SVCD (Super
Video Compact Disc), jpeg
CD, mp3, WMA
Loading disc
1. Press
on the front panel or press and hold
•
STOP on the remote control to open the disc
tray.
2. Insert a compatible disc into the disc slot.
See page 24 and 25 for more information about
discs and compatible formats.
3. Press
again to close the disc tray.
Regional coding
Your unit has been designed to process regional
management information stored on DVD
discs. The regional code for your unit is 1. Discs
that have a different regional code will not play.
8
Download from Www.Somanuals.com. All Manuals Search And Download.
RTD215 EN 6/2/07 3:36 PM Page 17
Basic playback operations
Zoom
1. While a disc is playing, press ZOOM until you
reach the zoom size you want. The ZOOM
button toggles through 2x, 3x, 4x and then
zooms out to 1/2x, 1/3x and 1/4x, then returns
to normal playback.
2. Move from one area to another (pan) using
the arrow buttons.
3. To turn ZOOM off, press ZOOM unitil you get
to the ZOOM OFF option.
Playback
EN
Switch the unit and the TV set on.
1. After loading a disc, playback starts
automatically, or the disc menu appears.
If the disc menu appears, select the Play
option to begin playback.
2. Press STOP to stop playback.
Accelerated play
Types of menus
While the disc is playing, press REVERSE or
FORWARD one or more times to vary the
speed and direction of the accelerated play. Press
PLAY to resume normal playback.
• Disc menu — The appearance and contents of
this menu varies according to the type of disc
you have inserted. It is separate from the Setup
menu.
• Info menu — The unit’s Info menu appears at
the top of the screen while the disc is playing.
Press INFO on the remote to switch the Info
menu on or off.
Pause
While the disc is playing, press PAUSE once for
freeze frame. Press PLAY to resume normal
playback.
TT
CH
Frame advance
• Setup menu — Press SETUP to access this menu.
1. Press PAUSE twice. FRAME is displayed.
2. Press FWD to move forward one frame
at a time.
GENERAL SETUP
3. Press PLAY to resume normal playback.
PASSWORD
RATING
SLIDE TIME
DEFAULT
Variable slow motion
1. While the disc is playing, press PAUSE once.
PAUSE is displayed.
EXIT SETUP
2. Press REV or FWD a number of times to vary
the speed.
3. Press PLAY to resume normal playback.
Changing chapter/track
While the disc is playing, press the CH+/- button
to go immediately to the next or previous
chapter, or to the next or previous track.
9
Download from Www.Somanuals.com. All Manuals Search And Download.
RTD215 EN 6/2/07 3:36 PM Page 18
Playing Discs - Basic Functions
Notes:
If the unit is left in STOP mode for more than
five minutes without any user interaction, a
screen saver is activated. At the end of 30
minutes without any user interaction, the
unit switches off automatically.
• When you press STOP, the unit stores the
EN
point where playback was interrupted. If you
press PLAY again, playback resumes from this
point. To stop playback completely or to start
again from the beginning, press STOP twice.
• REV slow motion is not available on VCDs.
The Info Menu
Using the Info menu
DVD Info Display
1. Press INFO on the remote while a disc is
playing to display the Info menu. The first
banner shows title, chapter, and time display
information.
title
chapter
time display
TT
CH
2. Press INFO again for audio language, subtitles,
and camera angle.
audio language
subtitles
camera angle
3. Press INFO a third time for play mode,
bookmark and sleep timer.
5
.
1
C
H
OFF
4. Use the right/left arrow buttons on the remote
to select an icon.
play mode
bookmark
sleep timer
5. Use the up/down buttons to scroll through the
options.
P
LA
Note:
VCD Info Display
INVALID KEY will be displayed if the
function you select is not available.
track
time display
P
BC
T
RK
play mode
bookmark
sleep timer
PLA
10
Download from Www.Somanuals.com. All Manuals Search And Download.
RTD215 EN 6/2/07 3:36 PM Page 19
Audio (DVD, VCD)
CD Info Display
Some discs have several audio tracks used for
different languages or different audio formats.
To change the language or audio format during
playback:
track
time display
EN
T
R
K
1. Press the INFO button twice.
play mode
bookmark
sleep timer
2. Use the left/right arrow buttons to select the
Audio icon, or press the AUDIO button on the
remote control.
PLA
3. Choose a language or an audio format with
the up/down arrow buttons.
Title/chapter (DVD)/track
(audio CD and VCD)
To directly access a title, chapter (DVD) or a track
(audio CD and VCD), press INFO, press OK. Select
the Title(TT), Track(TRK) or Chapter(CH) icon and
enter a number directly with the numeric
buttons. Press OK again to confirm.
This option is only available if the disc offers
dialog languages or audio formats. When you
change the dialog language using the Info menu,
it only changes the dialog language of the disc
being played. When you eject the disc or switch
off the unit, the language will revert to the one
you selected in the Language Setup menu (see
page 21).
Subtitles (DVD)
Subtitles are turned off by default. Turn on
Subtitles as follows:
Note:
• Many discs only have one title.
Time display
To access the Time Display, press INFO on the
remote. Press the up/down buttons repeatedly to
display:
DVD: Chapter elapsed time, Chapter remaining
time, Title elapsed time and Title remaining time.
VCD and audio CD: Track elapsed time, track
remaining time, disc elapsed time, disc remaining
time.
1. While the disc is playing, press INFO twice,
then select the Subtitles icon using the
left/right arrow buttons.
2. Select a language using the up/down arrow
buttons.
3. To turn subtitles off, select the Off option or
press SUBTITLE on the remote.
When you change the language of the subtitles
using the Info menu, it only applies to the disc
currently being played. When you eject the disc
and switch off the unit, the subtitles will default
to the subtitle language you selected in the
Languages menu (see page 21). This function may
not be available on all discs.
To directly access a location on the disc which
does not correspond to the start of a title or
chapter, press INFO once and press OK, highlight
the Time Display icon using the arrow buttons,
then enter a time with the number buttons
(hh:mm:ss) and press OK.
Note: Time display function may not be
available on all discs.
11
Download from Www.Somanuals.com. All Manuals Search And Download.
RTD215 EN 6/2/07 3:36 PM Page 20
The Info Menu
Camera angle (DVD)
Creating a Program List for Program Play
Mode (Audio CDs, DVD and VCD discs)
Some discs offer different camera angles for
specific scenes.
EN
To use program play mode, you must first create
a program list.
1. To change the camera angle, press the ANGLE
button on the remote or press the INFO button
twice and select the Camera angle icon with
the left/right buttons.
2. Choose the angle with the up/down arrow
buttons.
1. To create a program list, press the INFO button
three times. Highlight the Play Mode option
and press the up arrow to select the Program
option.
2. Press OK. The Program screen is displayed.
3. The first spot in the list is highlighted. Use the
number buttons on the remote to enter a track
number. As for DVD discs: T stands for Title
while C stands for Chapter. As for VCD discs
and Audio CDs: T stands for Track.
4. Use the arrow buttons to move to the next
spot in the list. Enter the next track number.
5. Continue entering tracks until you have
completed your list.
6. Highlight the Play option at the bottom of the
screen and press OK or press PLAY to start
playback. The program list will play in the
order you programmed it.
If the disc was recorded using a single camera
angle, this function is not available.
Play mode (all discs except
mp3/WMA/jpeg)
1. While the disc is playing, press the INFO button
twice for CD/VCD and three times for DVD.
2. Select the Play Mode icon using the left/right
arrow buttons.
3. Use the up/down arrow buttons to select an
option.
• DVD play modes: standard, program, A-B
repeat, title repeat, chapter repeat.
To stop program play, press STOP or select
Standard from the Play Mode option in the INFO
display.
Program play mode is only available if a program
list has been created (see below).
Repeat mode is only available with discs that
display elapsed time and remaining time.
To repeat a sequence between points A and B,
choose the A-B repeat option, and then follow
the instructions for entering the two points.
• VCD and SVCD play modes: standard, program,
disc repeat, track repeat, A-B repeat.
If you want to cancel the list, repeat steps 1 and 2
to select CLEAR and press OK.
• Audio CD play modes: standard, introscan,
random, program, repeat A-B, repeat disc,
repeat track.
4. To stop repeat playback, select the Play Mode
icon and use the up/down arrow buttons to
choose the Standard option.
Note:
• For mp3 play modes, please refer to
page 14.
12
Download from Www.Somanuals.com. All Manuals Search And Download.
RTD215 EN 6/2/07 3:36 PM Page 21
Creating a program List for program
play mode (mp3 CDs)
To use program play mode with an mp3 disc, you
must first create a program list. You can program
up to 16 songs.
1. To create a program list, press the INFO button
twice. Highlight the Play Mode option and
press the down arrow to select the Program
option.
2. Press OK. The Program screen is displayed.
3. The F stands for Folder, and the T stands for
Track. Highlight the space below the Folder
indicator (F) and use the number buttons to
enter the desired folder number.
Note: This function is only available
with discs whose elapsed time or remaining
time appears in the Info menu.
EN
Sleep
1. Press INFO twice for CD/VCD and three times
for DVD. Select Sleep icon with the left/right
arrow buttons.
2. Select one of the available options using the
OK button or pressing the SLEEP button on the
remote: Off, 30, 60, 90 or 120 minutes.
PBC (Playback Control – VCD)
When playing a VCD, PBC gives you access to
scenes and information that can be selected
through a menu. PBC also lets you display high-
resolution pictures, if the disc contains any.
1. Press INFO, then select the PBC icon with the
left/right arrow buttons.
4. Use the arrow buttons to move to the space
beneath the Track indicator (T). Use the
number buttons to enter the track number.
5. Repeat steps 3 and 4 until you have completed
your list.
6. Highlight the Play option at the bottom of the
screen and press OK or press PLAY to start
playback. The program list will play in the
order you programmed it.
2. Press OK.
3. Use the up/down arrow buttons to turn PBC on
or off, or press the DISC MENU button on the
remote.
To stop program play, press STOP or select
Standard from the Play Mode option in the INFO
display.
Introscan (CD)
This option plays the first ten seconds of each
track on a CD.
If you want to cancel the list, repeat steps 1 and 2
to select CLEAR and press OK.
1. Press the INFO button twice, then select the
Playmode icon with the left/right arrow
buttons.
2. Press the up/down arrow buttons to select the
INTRO option and press OK to start IntroScan.
3. Press STOP to stop Introscan, and press PLAY to
resume normal playback.
Bookmark (DVD and audio CD)
1. Press INFO twice for CD/VCD and three times
for DVD. Select the Bookmark icon with the
left/right buttons, and press OK. A menu is
displayed with five bookmarks.
2. The first bookmark space is highlighted. Press
OK to set the bookmark. The book mark is
saved and is indicated by the number 1. You
can set up to five bookmarks on a disc.
3. To start playback from a bookmark, press the
PLAY button on the remote.
4. To delete a bookmark, highlight it and press
CLEAR.
13
Download from Www.Somanuals.com. All Manuals Search And Download.
RTD215 EN 6/2/07 3:36 PM Page 22
Mp3/WMA Files and jpeg Files
Playing mp3/WMA files or displaying
jpeg files
During the slide show you can use the
left/right button to rotate the picture, the up
arrow button to rotate the image vertically,
the down arrow button to rotate the image
horizontally. Use the ZOOM button to magnify
the picture. Use the CH- button to go back to
the previous picture or the CH+ button to go
to the next one, and the STOP button to
interrupt the slide show and display the disc’s
contents.
EN
Mp3/WMA is an audio file format which
compresses recorded music. The main advantage
of the mp3/WMA format is that CD-quality music
tracks can be stored on a personal computer in
user friendly compressed files.
Jpeg files are image files. Make sure that they
have a resolution of less than 2 megapixels.
5. Press INFO to display the Info menu during
playback. mp3/WMA file: with the disc playing,
press INFO two times and select the Play Mode
icon using the left/right arrow buttons. Press
the up/down arrow button to select a play
mode (Standard, Random, Program, Repeat
Folder, Repeat Disc and Repeat Track), and
press OK.
1. Open the disc tray.
2. Place the disc with the printed side facing up
and close the disc tray.
The folders on the disc will be listed in
numerical order on the left side of the screen.
When you highlight a folder, the list of songs
or pictures in the folder are listed in numerical
order on the right side of the screen.
3. Select a folder using the up/down arrow
buttons on the remote, then press the left
arrow button to move to the music/picture
icons at the bottom of the screen. Use the
left/right arrow buttons to select either music
or picture mode.
6. When the unit has played all the files, the
music or slide show stops and the disc’s
contents are displayed again.
7. Press STOP to end playback.
Notes:
4. Press the up arrow button to move to the file
list on the right side of the screen. Use the
up/down arrow buttons to select a file. Press
OK or PLAY to start playback.
• mp3/WMA files and jpeg files could not
playback simultaneously.
• The time taken for the contents of the disc
to be displayed varies according to the size
and number of jpeg files on the disc. If
nothing is displayed after a few minutes, the
file sizes may be too large. Reduce the files’
resolution and write another disc.
• Before inserting a disc, make sure it is
compatible with the unit.
• mp3/WMA file: the unit begins playing the
selected file, then all the files and subfolders
contained in the same folder. The unit then
plays the contents of the folders at the same
level as the folder containing the file selected
at the start.
• jpeg file: the unit starts the slide show with
the jpeg file you have selected, then displays
all the jpeg files in the same folder, then all the
jpeg files in the subfolders located in the same
folder. You can set the amount of time a
picture remains on the screen in the General
Setup menu (see page 19).
14
Download from Www.Somanuals.com. All Manuals Search And Download.
RTD215 EN 6/2/07 3:36 PM Page 23
Radio
The unit has a built-in tuner that allows for FM
radio function. The AM loop antenna allows for
AM radio function.
Manual preset
1. Tune to a radio station (see “Manual tuning”
for details).
EN
2. Press MEMORY. While the Program Preset
number is still flashing, input your desired
preset number using the numeric buttons or
press the CH+/- buttons, then press MEMORY
to store it.
Manual tuning
1. Connect the FM antenna and the AM loop
antenna at the back of the unit. Rotate the
AM loop for better reception.
2. Press TUNER.
Retrieving preset stations
3. Tune a station by pressing TUNER+/- repeatedly
until the desired station is found. Alternatively,
you can press and hold the same buttons down
for about one second to activate the automatic
search function. In this mode the unit will
automatically tune frequencies until it finds a
station.
1. Press TUNER to enter the Tuner mode.
2. Press CH +/- to search up or down for the
preset stations or directly press the numeric
buttons.
4. Repeat step 3 to tune to another radio
station.
5. Press TUNER to toggle between FM and AM.
Tips:
• When the FM station broadcasts Stereo
sound is found, ST is displayed.
• When you manually tune into a weak FM
station, press AUDIO on remote control to
switch from Stereo to Mono mode. This
will reduce the background noise.
• If there is any interference, change the
antenna’s position until ideal sound
reception is obtained. TV and other
electronic devices could be the cause of
interference, so try to position the antenna
away from them.
Storing radio stations
The unit can store up to 30 radio stations in its
memory. You can enter every single radio station
yourself or the unit can store all available radio
stations automatically in ascending order.
Automatic preset programming
1. Press TUNER to enter the Tuner mode.
2. Press and hold TUNER for two seconds to start
automatic preset programming.
3. Radio frequencies will be browsed and radio
stations stored automatically. When all the
available radio stations are stored or all 30
memory locations are full, the auto preset
programming function will stop.
• A weak signal can affect the “Automatic
preset programming” function’s efficiency.
Adjust the antenna for better reception
and a more efficient search.
15
Download from Www.Somanuals.com. All Manuals Search And Download.
RTD215 EN 6/2/07 3:36 PM Page 24
USB Device
An overview
USB device playback features
This unit supports MSC devices. You can connect
1. Press USB to select USB mode.
2. Playback starts automatically. Press PAUSE to
pause playback and press PLAY again to
resume.
your own USB storage devices, then you can start
playback.
EN
3. Press STOP to end playback.
Connecting/Disconnecting USB device
to the Unit
Insert the USB drive's connector into the main
unit’s USB jack of the unit. To disconnect, unplug
the drive.
4. Press CH+/- buttons on the remote control to
skip to the previous or next file.
5. You may also follow the playback instruction
steps 3-7 on playing mp3/WMA files and jpeg
files on P.14.
Note: The unit only support
mp3/WMA/jpeg files on USB device.
16
Download from Www.Somanuals.com. All Manuals Search And Download.
RTD215 EN 6/2/07 3:36 PM Page 25
CD Ripping
An overview
When ripping has finished, press REC to quit the
ripping menu.
CD ripping allows you to rip tracks on CD to USB
device. This unit supports Mass Storage Class (MSC)
devices. Connect the USB device first before
ripping.
EN
File Names of Ripped Files
You can find the ripped files saved in a folder
named “CDRECORD” with file name as
“CDTKxx01”, “CDTKxx02”...etc.
Ripping CD to USB device
1. During CD playback, press REC on the remote
to activate the Ripping Menu.
2. Select one of the menu items using the
up/down arrow buttons. Press the left/right
arrow buttons or OK to change the setting.
Deleting Files
In USB mode, select the unwanted files by
pressing the arrow buttons. Press and hold CLEAR
on remote to delete files and select YES and press
OK to confirm deletion.
Speed
[
\
]
008_AP-1.MP3
High speed ripping mode can save time when
ripping from CDs. Select 1x(normal speed) or
2x(double speed) by pressing the left/right arrow
buttons. Press the down arrow button to move to
the next menu item.
01
ARE YOU SURE YOU WANT
02
03
TO DELETE IT?
RETURN TO ORIGINAL
SETTING IN 14 SECONDS.
Source
You can select to rip one track(TRACK), the whole
disc(ALL TRACKS) or programed tracks
(PROGRAM). Press the down arrow button to
move to the next menu item.
Notes:
• The USB device for CD ripping must be
connected to the unit in Mass Storage Class
(MSC) mode. Your device should be shown
as a drive letter, instead of the name of
the USB device, when connected to the
computer in MSC mode.
Destination
The destination of the ripped files is defaulted as
USB. No selection is needed.
Start Ripping CD
Highlight START and press OK to start ripping.
• CD Ripping function only supports CDDA
discs.
• No sound will be heard during ripping if
you select 2x(double speed).
• CD Ripping function does not support
ripping files to Multi Card Reader via USB
port.
• “NO USB DEVICE” will be displayed if no
USB device is connected to the unit.
“NO PROGRAM TRACK” will be displayed
if no program list is created.
“USB DEVICE IS FULL” will be displayed if
the USB device is full.
The screen above appears when ripping start.
The first progress bar represents the progress
percentage of the current ripping track while
the second progress bar represents the total
percentage. The percentage of both bars will
be identical if there is only one track to rip.
“USB WRITE PROTECT” will be displayed if
the USB device is write-protected. You
should switch off the write protection first.
• You can select ripping speed even after
ripping is started. Highlight the SPEED
option and press the left/right arrow
buttons.
To stop ripping during the process, highlight
STOP button and press OK.
• “DEVICE REMAIN” indicates the total
remaining time of the USB device.
17
Download from Www.Somanuals.com. All Manuals Search And Download.
RTD215 EN 6/2/07 3:36 PM Page 26
The Setup Menu
There are four options in the main setup menu:
General Setup, Display Setup, Speaker Setup and
Language Setup.
GENERAL SETUP
EN
LOCK
UNLOCK
PASSWORD
RATING
SLIDE TIME
DEFAULT
Press SETUP to bring up the main menu. Select
one of the menu icons across the top of the
screen using the left/right arrow buttons. The
menu’s options are displayed on the left side of
the screen. Press the right arrow button to move
to the option’s choices on the right. Highlight
EXIT SETUP and press OK if you want to exit
setup.
EXIT SETUP
Password for Unlocking the Unit
1. To unlock the unit or set a new password,
highlight the PASSWORD option using the
up/down arrow buttons and select UNLOCK.
2. Enter your password and press OK.
General Setup
You can control access to the unit and the type
of discs your family can watch with the lock
function. Locking the unit prevents playback of
DVDs that may not be suitable for all audiences
by using the rating level encoded on the disc (not
all discs are rated). If the rating level of the disc is
higher than the preset level, playback is
GENERAL SETUP
prohibited unless a password is entered.
EXIT SETUP
GENERAL SETUP
PASSWORD
RATING
Changing the Password
SLIDE TIME
DEFAULT
When you unlock the unit, you must assign a new
password the next time you lock the unit.
To change the current password, unlock the unit
as described above, and then relock it.
EXIT SETUP
Password for Locking the Unit
1. To activate locking according to your preset
rating limits, highlight the PASSWORD option
using the up/down arrow buttons and select
LOCK and press OK.
2. You are asked for a new password. Enter four
digits using the number buttons and press OK.
3. You are asked for confirmation; enter the four
digits again and press OK.
Note:
• Choose a password that is easy to remember,
or write it down.
• Use the super password: 9688 if you have
forgotten your password.
18
Download from Www.Somanuals.com. All Manuals Search And Download.
RTD215 EN 6/2/07 3:36 PM Page 27
Rating Explanations
Display Setup
1. Select the Display icon in the main menu using
the left/right arrow buttons.
•
The disc publisher is responsible for coding
scenes according to the rating limits. Below is
an explanation of Ratings.
EN
2. Select a menu option using the up/down arrow
buttons and press OK.
•
To change the rating limit, highlight the
RATING option and press the right arrow
button. Select the rating limit using the
up/down arrow buttons and press OK.
Rating limits take affect only when the unit is
locked.
DISPLAY SETUP
•
DISPLAY TYPE
DARK LEVEL
VIDEO
1 KID SAFE – Kid safe; it is safe even for kids.
2 G – General Audience; recommended as
acceptable for viewers of all ages.
3 PG – Parental Guidance suggested.
4 PG13 – Material is unsuitable for children
under age 13.
5 PG-R – Parental Guidance-restricted;
recommended that parents restrict children
under age 17 from viewing or allow
children to view only when supervised by a
parent or adult guardian.
6 R – Restricted, under 17 requires
accompanying parent or adult guardian.
7 NC17 – NO children under age 17; not
recommended viewing for children under
age 17.
EXIT SETUP
Display Type
Depending on the format of the DVD disc, you
can choose the picture format (aspect ratio) best
suited to the format of your TV screen:
4x3 PS: reproduces a 4x3 picture without
distortion.
4x3 LB: gives best reproduction of pictures
recorded in this format (i.e. with horizontal
bands at the top and bottom of the screen) or
in 16x9.
16x9 (widescreen): reproduces 16x9 format
films in full on a 16x9 screen.
•
•
•
8 ADULT – Mature material; should be viewed
only by adults, due to graphic sexual
material, violence, or language.
Dark level
This option lets you adjust the video brightness
level on a scale of 0 to 12, with 12 being the
brightest.
Slide Time
The Slide Time option lets you select the amount
of time a picture is displayed in a slide show. The
choices are 3 seconds, 5 seconds, or 10 seconds.
DISPLAY SETUP
DISPLAY TYPE
DARK LEVEL
VIDEO
Default
This option allows you to return the unit’s
settings to the original factory settings. Any
changes you have made to the unit’s settings will
be reverted back to the original settings, except
the password.
EXIT SETUP
19
Download from Www.Somanuals.com. All Manuals Search And Download.
RTD215 EN 6/2/07 3:36 PM Page 28
The Setup Menu
Video
Night Mode
Progressive Function provides high quality
pictures with less flickering. Turn on Progressive
Scan if you used the Component Video jacks of
the unit to connect a TV or monitor compatible
with a progressive scan signal.
You can use this function to control the different
sound levels via dynamic compression. It improves
the quality of the sound track at a low volume,
and quiets the loudest sounds. You can choose
between Quiet, Moderate or Off.
EN
Distance
Select ON and press OK to activate Progressive
Scan.
Basic settings have been preset for the speakers
included with your unit. However, to suit the
acoustic conditions in your listening room and to
make the sound more effective, you may need to
delay the signal coming from some of the
speakers. Channel delay compensates for center
or surround speakers that are closer to the
listening position than the front speakers.
1. Highlight a distance option using the up/down
arrow buttons.
IMPORTANT!
!
Once Progressive Scan has been activated,
an image will only be visible on a progressive
scan TV or monitor. If you choose this option
and you do not have a progressive scan TV or
monitor, you may get a picture with incorrect
color or no color.
Press and hold SUBWOOFER on the front panel.
The video output will be restored to the
standard setting and a picture will once again
be visible on a conventional analog TV or
monitor.
• Front (FL/FR DISTANCE)
• Center (CT DISTANCE)
• Surround (SL/SR DISTANCE)
2. Press the right arrow button to move to the
default distance.
3. Press the up/down arrow buttons to adjust the
distance.
Speaker Setup
You can adapt your unit to other equipment and
access specific functions with the Speaker
Setup menu.
1. Select the Speaker Setup icon in the main
menu using the left/right arrow buttons.
2. Select an option using the up/down arrow
buttons. Press the right arrow to move to the
option’s choices.
Test Tone
This function is used to test the speaker setting
and change the speaker level. A short noise
comes successively from each speaker.
Notes:
• Night mode function is available only on
DVD discs recorded in Dolby Digital.
• The receiver speaker distance default
settings are as follows:
SPEAKER SETUP
NIGHT MODE
FL/FR DISTANCE
CT DISTANCE
SL/SR DISTANCE
TEST TONE
Front (FR/FL Dist.)
Center (Cen Dist.)
15 ft
15 ft
Surroudn (SR/SL Dist.) 10 ft
EXIT SETUP
20
Download from Www.Somanuals.com. All Manuals Search And Download.
RTD215 EN 6/2/07 3:36 PM Page 29
Language Setup
With this menu, you can set the language for unit
menus, dialog, subtitles and the disc menus.
Subtitles
Select the subtitle language using up/down arrow
buttons and press OK.
EN
To change the language of the subtitles during
playback, press INFO twice for DVD and use the
left/right arrow buttons to highlight the Subtitle
icon. Press the up/down arrow buttons or the
SUBTITLE button on the remote to select a
subtitle language.
If you chose “English” during initial set-up, any
menus generated by the disc are in English, and
so is the language of the dialogs (if this language
is available on the disc).
LANGUAGE SETUP
Disc Menu
PLAYER MENU
AUDIO
To change the language of the disc menus, select
the language using the up/down arrow buttons
and press OK.
SUBTITLE
DISC MENU
EXIT SETUP
The language you select will only be displayed if
the disc is programmed with that language.
1. Select the Language Setup icon in the main
menu using the left/right arrow buttons.
2. Select one of the options using the up/down
arrow buttons.
3. Press the right arrow button to move to the
language choices.
Notes:
• If the selected language is not available
on a disc, the disc’s language will be used
instead.
• If the language chosen is available, it is
automatically selected when you display
the subtitles or press SUBTITLE on the
remote control. Otherwise, the subtitle
language indicated on the disc is selected.
4. Use the up/down arrow buttons to highlight
the language of your choice and press OK.
Player Menu
Select the language of player menus and press
OK.
Audio
Select the dialog language using up/down arrow
buttons and press OK.
To change the Audio language during playback,
press INFO twice for DVD and use the left/right
arrow buttons to highlight the Audio icon.
Press the up/down arrow buttons or AUDIO on
the remote control to select audio language.
21
Download from Www.Somanuals.com. All Manuals Search And Download.
RTD215 EN 6/2/07 3:36 PM Page 30
Additional Information
Troubleshooting
Problem
Solution
Problem
Solution
EN
The unit
does not
switch on.
• Make sure it is plugged in.
• Press the ON•OFF button
on the remote control or the
ON/STANDBY button on the front
of the unit.
No surround • Check the speaker
sound.
configuration in the Setup
menu (See Positioning speaker
on pages 4-5 or Speaker Setup
on page 20).
The device
switches off
spontane-
ously.
• The device switches off
automatically when it is in STOP
mode for more than 30 minutes
without any user intervention.
Switch it on again.
I can’t find
my file in
the
WMA/mp3/
jpeg listing.
• Make sure the filename is
valid (see page 24 and 25).
• It might be impossible to
read the disc.
• Insert the disc with the printed
side facing up.
The remote • Check that batteries are
control does inserted or change them.
not work or • Aim the remote control at the
• Check that the disc can actually
be played by this device
(see page 24).
• Check that the disc’s regional
code matches the unit’s regional
code. This unit’s regional code is 1.
• Clean the disc.
works only
intermittently
unit. The infrared beam must
not be blocked or interrupted.
• Check that the remote control
is configured to control the
device you are trying to
operate with it.
The subtitles • Check that the DVD disc
• Check you have switched on
the TV set.
• Check the connections (see pages
2, 20 and Quick Start Guide).
• Select the AV input assigned to
the unit on the TV.
do not
appear.
provides subtitles.
• Refer to the section on how to
display subtitles (see page 11).
There is no
picture.
The disc
menu
• The disc menu language has
not been set up (see page 21).
• Check the connections (see pages language is • The language of your choice
The picture
is of poor
quality
2 and 20 and Quick Start Guide).
not the
correct one.
is not available on the disc
(see page 21).
(with snow
or lines).
You have
forgotten
your
password
(Parental
control).
• Use the super password: 9688.
• Check the connections (see
page 2 and 3).
• Make sure the speakers are
connected.
• Make sure the MUTE function
is not on.
There is no
sound or
the sound
is of poor
quality.
22
Download from Www.Somanuals.com. All Manuals Search And Download.
RTD215 EN 6/2/07 3:36 PM Page 31
Precautions
Use
Handling and caring for discs
• Handle your discs with care. Hold the disc with
your fingers at the edges or through the hole.
• Insert the disc with the label facing up (for a
single-sided disc).
• Place the disc properly into the tray in the
allotted holder.
• Use a soft cloth to clean discs if necessary,
always wiping from the centre to the edge.
• Always put discs back in their cases after use
and store in a vertical position.
• Do not close the tray with two discs in it or
with a disc not sitting correctly in the holder.
• Do not play cracked, chipped or warped
discs nor try to repair them with adhesive
tape or glue.
EN
• If your unit has been stored in a cool place for
any length of time, during a journey for
example, wait for about 2 hours before
using it.
• The openings located on the top and bottom
are for ventilation and must not be obstructed.
• During thunderstorms, we recommend that
you isolate the unit from the electrical supply
so that it is not damaged by electrical or
electromagnetic surges.
• This unit is designed for continuous use.
Switching off the unit to standby mode does
not disconnect it from the mains supply. To
completely isolate the equipment, remove the
plug from the mains jack as some components
remain connected to the electrical supply.
• If you notice any burning or smoke, disconnect
the unit immediately to avoid any risk of
electrocution.
• Do not attempt to look inside the unit through
the disk tray opening or any other opening.
You may be electrocuted or exposed to
laser radiation.
• Do not write on a disc.
• Do not move the unit when a disc is
being played.
• Do not scratch discs or store them in places
exposed to direct sunlight, high humidity or
high temperatures.
• Do not use aerosol cleaners, benzene, anti-
static liquids or any other solvent for cleaning
discs. When cleaning, wipe gently with a soft
damp (water only) cloth from the centre to the
edge, avoiding circular motions, which could
cause scratches and interference
• This unit is for domestic use only and must not
be used for industrial purposes.
• Total or partial copying of recordings protected
by copyright legislation, without the explicit
permission of the holder of the rights,
contravenes current legislation. Copying or
downloading music files for sale or any other
business purpose constitutes or could
constitute a violation of copyright law.
during playback.
Cleaning
• Use a soft, dry, clean cloth. Regularly dust the
vents at the back or sides.
• Using solvents, abrasive or alcohol-based
products risks damaging the unit.
• If an object or liquid enters inside the unit,
unplug it immediately and have it checked by
an authorized servicer or service center.
23
Download from Www.Somanuals.com. All Manuals Search And Download.
RTD215 EN 6/2/07 3:36 PM Page 32
Additional Information
Compatible Formats
software). However, depending on the
condition of the CD-writer, computer and the disc
used, you may find that not all discs will play.
When playing a CD-R disc, it is normal for the
unit to take up to 20 seconds to recognize
the disc before starting to play.
In order to ensure playback, discs must conform
with DVD, CD, VCD or SVCD standards. This unit
EN
may not play some recordings or files due to
differences in recording formats, software used
and disc types.
If the disc is not recognized after a period of 20
seconds, remove the disc, and insert it again.
DVD-Video
Digital video discs - 12 cm, single or
double sided, single or dual layer. DVDs
are high density optical discs on which
high quality picture and audio are recorded by
means of digital signals.
• Do not use its full capacity.
• CD-Rs should be preferably used instead of
CD-RWs (rewritable CDs) as, in certain cases,
CD-RW playback may be faulty.
• Use reliable, good-quality CD write software.
• Close all other applications on the computer to
ensure reliable CD-R disc recording.
DVD-R,DVD-RW, DVD+R, DVD+RW
Most DVD-R and DVD+R (one recording
only), DVD-RW and DVD+RW discs
(rewritable), depending on the DVD writer
and discs used. Recordings using DVD-R
and DVD-RW discs must be made in Video
DVD mode. Recordings using DVD+RW discs must
be made in accordance with the specifications for
DVD+RW discs with a 4.7 GB capacity.
Mp3 files
DVD+Rewritable
CD-R and CD-RW discs containing
audio files in mp3 format. For CD-R
mp3 discs, please follow all the
recommendations for CD-R, along with the
comments below:
Video Compact Disc (VCD)
• Your mp3 files should be ISO 9660 or JOLIET
format. ISO 9660 format and Joliet mp3 files
are compatible with Microsoft’s DOS and
Windows, as well as with Apple Mac.
• Mp3 filenames should not exceed 8 characters,
and should end with the “.mp3” extension.
General name format: Title.mp3. When
composing your title, use 10 characters or less,
no spaces, and avoid the use of special
characters including (. , / , \ , = ,+).
CD on which you can record up to 74 min.
of VHS quality video associated with still
images, audio tracks and interactive
menus.
Super Video Compact Disc (SVCD)
Most SVCDs comply with the IEC62107 standard.
SVCDs can be used to record up to 70 minutes of
digital sound and images in accordance with
MPEG-2 standards for video and MPEG-1
standards for audio.
• The total number of files on a disc should be
less than 400.
• Use a decompression transfer rate of at least
128 kB/sec (kilobytes/second) when recording
mp3 files. Sound quality with mp3 files
basically depends on the rate of compression/
decompression you choose. Obtaining audio
CD quality sound requires an analog/digital
sampling rate, that is conversion to mp3
format, of at least 128 kB/sec and up to 160
kB/sec. Choosing higher rates, such as 192
kB/sec or more, only rarely produces even
better sound quality. Conversely, files with
sampling rates below 128 kB/sec will not
play properly.
Audio CDs
Audio CDs (12 cm).
CD-R, CD-RW
Most CD-R (one recording only) and CD-
RW discs (rewritable).
CD-Rs written during a multisession recording can
be played, provided that the session has ended
before the disc is played (depending on the write
24
Download from Www.Somanuals.com. All Manuals Search And Download.
RTD215 EN 6/2/07 3:36 PM Page 33
• Do not record copyright-protected mp3 files.
“Securized” files are encrypted and code
protected to prevent illegal copying.
Sound Enhancement Systems
This receiver is equipped with several built-in
sound enhancement systems.
EN
Important: The above recommendations
do not guarantee that the unit will play
mp3 recordings, or as an assurance of sound
quality. Certain technologies and methods
for mp3 file recording on CD-Rs prevent
optimal playback of these files on your unit
(i.e. degraded sound quality and in some cases,
inability of the unit to read the file).
Dolby Digital
Manufactured under license
from Dolby Laboratories.
"Dolby", "Pro Logic", and
the double-D symbol are
trademarks of Dolby
Laboratories.
The Dolby Digital mode lets you enjoy full digital
surround from software processed in the Dolby
Digital format. Dolby Digital provides better
sound quality and a more powerful presence than
conventional Dolby Surround. This unit is
jpeg files
CD-R and CD-RW with jpeg files. Certain jpeg
files, including progressive jpeg files, cannot be
read by this unit.
equipped with Dolby Digital 5.1-channel so that
you can enjoy enhanced full digital surround
sound. Different from Dolby Pro Logic in that
only four channels (Front Left, Front Right, Centre
and Rear ) are used, the new system provides
stereo separation of the rear speakers (Rear-
Right, Rear-Left ). Adding the to the 5 channels
the subwoofer channel for bass sounds (counted
as 0.1 channel) results in 5.1 channels (or 6
Channels) that bring you the most sophisticated
Dolby Digital sound enjoyment.
The total number of files and folders on the disc
should be less than 650. Make sure that files have
the “.jpg” extension. Files without the “.jpg”
extension will not be able to be read by the
unit — even though the files are shown as jpeg
images on your computer.
WMA files
CD-R and CD-RW discs containing audio
files in WMA (Windows Media Audio)
format. Please follow all the
recommendations for CD-R above.
25
Download from Www.Somanuals.com. All Manuals Search And Download.
RTD215 EN 6/2/07 3:36 PM Page 34
Additional Information
Technical Specifications:
Amplifier Section:
AM Tuner Section:
Frequency Response: 2kHz +/-3dB, 400Hz ref.
Usable Sensitivity: 3000uV/m @ S/N 20dB
Signal to Noise: 38dB
EN
RMS Output Power: Dolby Digital Mode with
10% Total Harmonic Distortion
Rear Channels: 32 Watts each Channel
(1KHz, 4Ohm)
Front and Center Channel: 32 Watts each Channel
(1KHz, 4Ohm)
Subwoofer Channel: 40 Watts (100Hz, 3Ohm)
Total RMS Output Power, Dolby Digital mode:
200W
IF Rejection: 35dB
FM Tuner Section:
Frequency Response: 15kHz +/-3dB, 1kHz ref.
Quieting: 24dB
Signal to Noise: 62dB(stereo) / 65dB(mono)
IF Rejection: 70dB
Dimensions (H x W x D mm) :
Unit: 66 x 360 x 334
FTC Output Power: Dolby Digital Mode with 10%
Total Harmonic Distortion
Front Speakers and Stands: 198 x 102 x 63
Front Speakers without Stands: 109 x 81 x 90
Center Speaker: 102 x 253 x 73
Rear Speakers: 198 x 102 x 63
Front Channels (L and R): 20 Watts per Channel
(1KHz, 4Ohm)
Rear Channels (L and R): 20 Watts per Channel
(1KHz, 4Ohm)
Center Channel: 30 Watts (1KHz, 4Ohm)
Subwoofer Channel: 35 Watts (100Hz, 3Ohm)
Total FTC Output Power, Dolby Digital mode:
145 Watts
Subwoofer: 308 x 162 x 265
Muting Attenuation: 70 dB
Frequency Response: 200Hz – 20KHz/3dB,
1KHz ref.
Subwoofer Frequency Response: 20Hz – 200Hz/
-3dB, 100Hz ref.
Signal to Noise Ratio: 70 dB (Dolby digital mode)
26
Download from Www.Somanuals.com. All Manuals Search And Download.
RTD215 EN 6/2/07 3:36 PM Page 35
Limited Warranty
What your warranty covers:
• Defects in materials or workmanship.
EN
For how long after your purchase:
• One year from date of purchase - Unit exchange, which includes parts and labor.
• The warranty for rental units begins with the first rental or 45 days from date of shipment to the
rental firm, whichever comes first.
What we will do:
• Exchange the defective unit for a new, or at our option, refurbished unit.
How you get service:
• Call 1-580-634-0366 and have your unit’s date of purchase and model/serial number ready. The
model/serial number information is on the back of your unit.
• A representative will troubleshoot your problem over the phone.
• If the representative determines that you should receive a replacement unit you will be provided
with a Service Request (SR) number. No returns will be accepted without the SR number.
• Proof of purchase in the form of a bill of sale or receipted invoice which is evidence that the product
is within the warranty period must be presented to obtain warranty service. For rental firms, proof
of first rental is also required.
Option I: Send you a replacement unit.
1. Provide your Discover, MasterCard or Visa account number and expiration date to your phone
representative. This is for security purposes only and your account will not be charged at this time.
2. We will send you a replacement unit.
3. If you return the defective unit to us within 14 days from the date you were provided a SR number,
only items not covered by warranty will be charged to your account. If your unit is not received
within 14 days, the suggested retail value of the unit will be charged to your credit card. This
amount will be credited, less a handling fee, if the unit is subsequently received.
4. Ship your defective unit back to us, less accessories, using the replacement unit’s carton. Shipping
instructions will be included in the carton along with your SR number which will allow you to easily
ship the unit back to us. Make sure you insure your shipment in case of damage or loss. Include with
the shipment:
• Evidence of purchase date such as a bill of sale.
• A brief note describing your unit’s problem.
• Your name, address and phone number.
Option II: Provide you a replacement unit at our exchange point.
1. For a fee, we will send a replacement unit to our exchange point.
2. The exchange location will notify you of its arrival.
3. Take your unit and evidence of purchase date, such as a bill of sale, to the exchange location and
you will be provided the new or refurbished unit. Please retain all accessories such as the remote
control hand unit.
4. If the repairs are covered by your warranty, you will not be billed. Thomson assumes no responsibility
for warranty shipments from the customer to the factory if not shipped in the manner prescribed by
Thomson.
To receive a replacement unit after we have received your unit:
• Write the SR number on the outside of the carton used to return the unit. Make sure you insure your
shipment in case of damage or loss.
• Carefully pack the unit using the original box and packing material if possible. Please retain all
accessories that were included with your unit such as the remote control hand unit.
27
Download from Www.Somanuals.com. All Manuals Search And Download.
RTD215 EN 6/2/07 3:36 PM Page 36
Limited Warranty
• Include with the shipment:
1. Evidence of purchase date such as a bill of sale.
2. A brief note describing your unit’s problem.
3. Your name, address and phone number.
EN
• The representative will advise the address to mail a cashier’s check or money order for payment if
there are any out of warranty labor or parts charges, and you elect not to use your credit card.
• After we receive your product, a new or refurbished unit will be shipped to you.
What your warranty does not cover:
• Acts of nature, such as but not limited to lightning damage.
• Adjustment of customer controls.
• Damage from misuse or neglect.
• A unit that has been modified or incorporated into other products or is used for institutional or
other commercial purposes.
• Batteries.
• Units purchased, serviced or operated outside the U.S.A.
• Loss of programming. It is recommended that you retain all original CD software that was loaded in
the unit.
• Installation.
• Shipping damage if the unit was not packed and shipped in the manner prescribed by Thomson.
• Storage fees may be charged by the exchange point if you fail to pick up the replacement unit in a
timely manner.
Product Registration:
• Please complete the online Product Registration on RCA.com/productregistration or complete and
mail the Product Registration Card packed with your product. This will make it easier to contact you
should it ever be necessary. The return of the card is not required for warranty coverage.
Limitation of Warranty:
• The warranty stated above is the only warranty applicable to this product. All other
warranties, express or implied (including all implied warranties of merchantability or
fitness for a particular purpose) are hereby disclaimed. No verbal or written information
given by Thomson, its agents or employees shall create a guaranty or in any way increase
the scope of this warranty.
• Repair or replacement as provided under this warranty is the exclusive remedy of the
consumer. Thomson shall not be liable for incidental or consequential damages resulting
from the use of this product or arising out of any breach of any express or implied
warranty on this product. This disclaimer of warranties and limited warranty are
governed by the laws of the state of Indiana. Except to the extent prohibited by
applicable law, any implied warranty of merchantability or fitness for a particular purpose
on this product is limited to the applicable warranty period set forth above.
How state law relates to warranty:
• Some states do not allow the exclusion nor limitation of incidental or consequential damages, or
limitations on how long an implied warranty lasts, so the above limitations or exclusions may not
apply to you.
• This warranty gives you specific legal rights, and you also may have other rights that vary from state
to state.
If you purchased your product outside the United States:
• This warranty does not apply. See your dealer for warranty information.
28
Download from Www.Somanuals.com. All Manuals Search And Download.
RTD215 EN[E] 16/5/07 2:22 PM Page 2
IMPORTADOR
Comercializadora Thomson de México, S.A. de C.V.
Álvaro Obregón No. 151. Piso 13.
Col. Roma. Delegación Cuauhtémoc
C.P. 06700. México, D.F.
Telefono: 52-55-11-020360
RFC: CTM-980723-KS5
EXPORTER
Thomson Inc.
P.O. Box 1976
Indianapolis, IN 46206-1976
© 2007 Thomson Inc.
Trademark(s)® Registered
Marque (s)® de commerce enregistrée (s)
Marca(s) Registrada(s)
Printed in China/
Imprimé en Chine
Impreso en China
5642498A (EN/E)
Download from Www.Somanuals.com. All Manuals Search And Download.
|