RCA Flat Panel Television D61W17B User Guide

HDTV Monitor

User’s Guide

Changing Entertainment. Again.

Download from Www.Somanuals.com. All Manuals Search And Download.

Important Information

IMPORTANT SAFETY INSTRUCTIONS

1. Read these instructions.

2. Keep these instructions.

3. Heed all warnings.

4. Follow all instructions.

5. Do not use this apparatus near water.

6. Clean only with dry cloth.

7. Do not block any ventilation openings. Install in accordance with the manufacturer’s instructions.

8. Do not install near any heat sources such as radiators, heat registers, stoves, or other apparatus (including ampliﬁers) that produce

heat.

9. Do not defeat the safety purpose of the polarized or grounding-type plug. A polarized plug has two blades with one wider than the

other. A grounding type plug has two blades and a third grounding prong. The wide blade or the third prong is provided for your

safety. If the provided plug does not ﬁt into your outlet, consult an electrician for replacement of the obsolete outlet.

10. Protect the power cord from being walked on or pinched particularly at plugs, convenience receptacles, and the point where they

exit from the apparatus.

11. Only use attachments/accessories speciﬁed by the manufacturer.

12. Use only with the cart, stand, tripod, bracket, or table speciﬁed by the manufacturer, or sold with the apparatus. When a

cart is used, use caution when moving the cart/apparatus combination to avoid injury from tip-over.

13. Unplug this apparatus during lightning storms or when unused for long periods of time.

14. Refer all servicing to qualiﬁed service personnel. Servicing is required when the apparatus has been damaged in any way, such as

power-supply cord or plug is damaged, liquid has been spilled or objects have fallen into the apparatus, the apparatus has been

exposed to rain or moisture, does not operate normally, or has been dropped.

If an outside antenna is connected to the TV receiver, be sure the antenna system is

grounded so as to provide some protection against voltage surges and built up static

Example of Antenna Grounding as per

(NEC) National Electrical Code

��

charges. In the U.S. Section 810-21 of the National Electrical Code and in Canada, Part 1 of

��

the Canadian Electrical Code provides information with respect to proper grounding of the

antenna system. See the ﬁgure on the right for details.

��

To assure adequate ventilation for this product, maintain a spacing

of 4 inches from the top and sides of the TV receiver and 2 inches

from the rear of the TV receiver and other surfaces.

Download from Www.Somanuals.com. All Manuals Search And Download.

Introduction

Key Features Overview

Your TV is equipped with features that will add to your TV viewing experience. The following

information summarizes a few of these features. Chapter 3 provides more information about the

rest of the TV’s features and how to use them.

Precision CRTs

Your HDTV Monitor features Precision CRTs. These Precision CRTs (cathode ray tubes) produce

sharp, high-resolution images, with great detail and better transition between images than

regular CRTs.

DVI-HDTV Input

Lets you connect a component with a DVI (Digital Visual Interface) output. DVI provides an

uncompressed, digital video interface developed for high-bandwidth digital connection. It

supports the overlay of high-resolution graphics needed by some electronic program guide

navigation and other interactive services. DVI, when combined with HDCP (High bandwidth

Digital Content Protection) technology, creates a protected digital connection. The DVI-HDTV

connection is designed to display either progressive scan (480p) or HDTV (1080i) signals at a

bandwidth of up to 1.78 Gigabits per second.

PIP (Picture-In-Picture) and POP (Picture-Outside-Picture)

Description: PIP lets you watch two channels at one time – one channel on the main screen

and the other in a smaller window. POP also lets you watch two channels at one time – one

channel on the left side of the screen (the main picture) and the other on the right.

Requirements: Press the PIP button to bring up the PIP window. Press again to bring up POP.

Chapter 3 has detailed instructions on how to use the PIP and POP features.

Note: PIP and POP are not available for DVI or component video sources (CMP1 or CMP2).

V-Chip: Parental Controls (for the U.S. and Canada)

Description: You can block programs and movies by content, age-based ratings, and/or movie

ratings.

Requirements:

•

Set up the Parental Control menu in the TV’s main menu (Chapter 3 has details).

The broadcasters must use the rating system when they send the program to your TV in

order for your TV to block the program.

•

Parental controls must be locked for these settings to take affect.

Download from Www.Somanuals.com. All Manuals Search And Download.

Table of Contents

Important Safety Instructions.......................................... 1

Channel 3: Special Features

Channel Banner............................................................... 24

Autotuning...................................................................... 24

Why You Should Use the Autotuning Feature ....... 24

How to Set Up the Autotuning Feature.................. 25

Parental Controls and V-Chip......................................... 26

How V-Chip Works for USA and Canada................. 26

Canada V-Chip Ratings............................................. 29

Blocking Canadian V-Chip Ratings .......................... 30

Lock/Unlock Parental Controls ............................... 31

V-Chip Movie Rating Limit ....................................... 31

Blocking Unrated/Exempt Programs .................... 31

Introduction

Key Features Overview .................................................... 2

Chapter 1: Setup & Connections

Things to Consider Before You Connect ......................... 4

Choose Your Connection.................................................. 5

Cables Needed to Connect Components

to Your TV............................................................... 5

TV + HDTV Tuner + VCR + DVD Player............................. 7

TV + Satellite Receiver + VCR........................................... 9

TV + DVD + VCR .............................................................. 11

TV+ A/V Receiver or Speakers........................................ 12

Explanation of Jacks ....................................................... 13

The Front of Your TV....................................................... 14

Front Input Jacks....................................................... 14

Front Panel Buttons.................................................. 15

Plug in the TV.................................................................. 15

Put batteries in the remote............................................ 15

PIP (Picture-in-Picture) and

POP (Picture-outside-Picture) Operation.................... 32

PIP and POP Buttons................................................. 32

Chapter 4: Using the Menu System

Sound Menu.................................................................... 33

Picture Menu ................................................................... 34

Channel Guide Menu...................................................... 36

Time Menu....................................................................... 36

Parental Control Menu ................................................... 36

PIP Menu.......................................................................... 37

Setup Menu..................................................................... 37

How to Use the Remote Control to Complete

the Initial Setup............................................................ 15

Complete Auto Channel Search............................... 16

Turn on the TV................................................................. 16

Complete the Initial Setup ............................................. 16

Set the Menu Language .......................................... 16

Changing Lists and Labels........................................ 17

Auto Convergence.................................................... 17

Chapter 5: Additional Information

Troubleshooting.............................................................. 39

FCC Information .............................................................. 41

Care and Cleaning........................................................... 41

RCA HDTV Monitor Limited Warranty........................... 42

Accessory Information.................................................... 44

Chapter 2: Using the Remote Control

The Buttons on the Remote Control.............................. 18

Programming the Remote.............................................. 20

Find Out If You Need to Program the Remote ...... 20

How to Use the Remote After You’ve

Programmed It ...................................................... 21

Using the INPUT Button.................................................. 22

Remote Control Codes.................................................... 22

Download from Www.Somanuals.com. All Manuals Search And Download.

Connections & Setup

Things to Consider Before You Connect

Protect Against Power Surges

•

Connect all components before you plug any of their power cords into the wall outlet.

Turn off the TV and/or component before you connect or disconnect any cables.

Make sure all antennas and cables are properly grounded. Refer to the Important Safety

Instructions on page 1.

Protect Components from Overheating

•

Don’t block ventilation holes on any of the components. Arrange the components so that air

can circulate freely.

•

Don’t stack components.

If you place components in a stand, make sure you allow adequate ventilation.

If you connect an audio receiver or ampliﬁer, place it on the top shelf so the heated air from it

won’t ﬂow around other components.

Position Cables Properly to Avoid Audio Interference

•

Insert each cable ﬁrmly into the designated jack.

•

If you place components above the TV, route all cables down the side of the back of the TV

instead of straight down the middle of the TV.

•

If your antenna uses 300-ohm twin lead cables, do not coil the cables. Also, keep the twin

lead cables away from audio/video cables.

Important Stand and Base Safety Information

Choose the location for your TV carefully. Place the TV on a stand or base that is of adequate size

and strength to prevent the TV from being accidentally tipped over, pushed off, or pulled off. This

could cause personal injury and/or damage the TV. Refer to the Important Safety Instructions on

page 1.

Use Indirect Light

Don’t place the TV where sunlight or room lighting will be directed toward the screen. Use soft or

indirect lighting.

Graphics contained within this publication are for representation only.

Chapter 1

Download from Www.Somanuals.com. All Manuals Search And Download.

Connections & Setup

Choose Your Connection

There are several ways to connect your TV. Please use the following chart to determine which connection is best for you.

Proceed to the appropriate page and connect your TV.

Note for US customers: If you prefer, we can provide you with the name of an Authorized Service Representative who

will visit your home for a fee to install your electronic entertainment system and to instruct you in its operation. For

details about this service, call 1-888-206-3359.

For additional assistance while using your RCA product, please visit www.rca.com/customersupport.

Components

Cables

Needed

Connection

Title

Go to...

Coaxial

Audio/video

TV + HDTV Tuner pages 6-7

+ DVD + VCR

Component

video

DVI-HDTV

Coaxial

TV + Satellite

Receiver + VCR

pages 8-9

Audio/video

S-Video

TV + DVD + VCR

Coaxial

pages 10-11

Audio/video

Component video

For general information on connecting an A/V receiver or speakers to your TV, go to page 12.

Cables Needed to Connect Components to Your TV

The pictures below show the cables needed for the connections represented in this book.

Audio/Video

cables

Component Video

(Y•Pb•Pr) cables

DVI-HDTV Cable

Coaxial cable

S-Video cable

Graphics contained within this publication are for representation only.

Chapter 1

Download from Www.Somanuals.com. All Manuals Search And Download.

Connections & Setup

��

�

��

�

��

�

��

�

��

�

��

�

��

�

��

�

AUDIO/VIDEO OUTPUT

��

�

��

�

��

�

��

�

��

�

��

�

��

�

��

�

��

�

��

Graphics contained within this publication are for representation only.

Chapter 1

Download from Www.Somanuals.com. All Manuals Search And Download.

Connections & Setup

TV + HDTV Tuner + VCR + DVD Player

1. Make sure cable or antenna and/or satellite is connected to your VCR.

A. Connect the coaxial cable from your cable outlet or antenna to the antenna input on the HDTV Tuner.

B. Connect the satellite dish antenna to the satellite input on the HDTV Tuner.

2. Make the video connection between your HDTV Tuner and the TV.

A. Best Connection: DVI-HDTV

Connect a DVI-HDTV cable to the DVI-HDTV jack on the back of your HDTV Tuner. Connect the other end of the

cable to the DVI-HDTV input on the back of TV.

– OR –

B. Very Good Connection: Connect three video grade cables to the CMP1 Y PB PR jacks on the back of the TV and to

the Y PB PR jacks on the HDTV Tuner.

Notes: The DVI-HDTV and Y PB PR jacks send the digital cable signal to the TV in digital and analog formats,

respectively.

3. Make the audio connection between your HDTV Tuner and the TV (to match your video connection).

A. If you used the DVI-HDTV jack:

Connect the audio (white and red) cables to the DVI-HDTV L and R audio jacks on the back of the TV and to the

Audio Output jacks on the HDTV Tuner.

– OR –

B. If you used the Component Video jacks:

Connect the audio (white and red) cables to the CMP1 L and R audio jacks on the back of the TV and to the Audio

Output jacks on the HDTV Tuner.

4. Connect your HDTV Tuner to your VCR.

A. Connect a coaxial cable to the HDTV Tuner’s antenna output and to VCR’s antenna input.

B. Connect the audio (white and red) cables to the Audio Output jacks on the HDTV Tuner and to the Audio Input

jacks on the VCR.

C. Connect the video cable to the Video Output jack on the HDTV Tuner and to the Video Input jack on the VCR.

5. Connect your VCR to your TV.

A. Connect a coaxial cable to the VCR’s antenna output and to the ANTENNA/CABLE Input jack on the TV.

B. Connect the audio (white and red) cables to the VID2 L/MONO and R audio jacks on the back of the TV and to the

Audio Output jacks on the VCR.

C. Connect the video cable to the VID2 V (video) jack on the back of the TV and to the Video Output jack on the VCR.

6. Connect your DVD player to your TV.

A. Connect the audio (white and red) cables to the CMP2 L and R audio jacks on the back of the TV and to the Audio

Output jacks on the DVD player.

B. Connect three video grade cables to the CMP2 Y PB PR jacks on the back of the TV and to the Y PB PR jacks on the

DVD player.

Notes: If your DVD player doesn’t have Y PB PR jacks, but does have an S-Video jack, connect the player to the TV’s

VID1 S-VIDEO jack using an S-Video cable.

If your DVD player doesn’t have an S-Video jack, connect the player to the TV’s VID1 V (video) jack using a video

cable.

Important: If you use the TV’s VID1 S-VIDEO or V (video) jack to connect the DVD player, you must connect the

audio cables to the TV’s VID1 L/MONO and R jacks.

Go to page 15

Graphics contained within this publication are for representation only.

Chapter 1

Download from Www.Somanuals.com. All Manuals Search And Download.

Connections & Setup

��

�

��

�

��

�

��

�

AUDIO/VIDEO OUTPUT

��

�

��

�

��

�

��

�

��

�

��

�

��

�

��

�

��

�

��

�

��

Graphics contained within this publication are for representation only.

Chapter 1

Download from Www.Somanuals.com. All Manuals Search And Download.

Connections & Setup

TV + Satellite Receiver + VCR

1. Connect your VCR to your TV.

A. Connect a coaxial cable to the VCR’s antenna output and to the ANTENNA/CABLE Input

jack on the TV.

B. Connect the audio (white and red) cables to the VID2 L/MONO and R Audio jacks on the

back of the TV and to the Audio Output jacks on the VCR.

C. Connect the video cable to the VID2 V (Video) jack on the back of the TV and to the Video

Output jack on the VCR.

2. Make sure cable or antenna is connected to your VCR.

Connect the coaxial cable from your cable outlet or antenna to the antenna input on the VCR.

3. Connect your Satellite Receiver to your TV.

A. Connect the audio (white and red) cables to the VID1 L/MONO and R Audio jacks on the

back of the TV and to the Audio Output jacks on the Satellite Receiver.

B. Connect the video cable to the VID1 V (Video) jack on the back of the TV and to the Video

Output jack on the Satellite Receiver.

C. If your Satellite Receiver has an S-Video jack, connect an S-Video cable (instead of the

video cable in step B) to the S-VIDEO jack on the TV and to the S-VIDEO jack on the

satellite receiver.

Go to page 15

Graphics contained within this publication are for representation only.

Chapter 1

Download from Www.Somanuals.com. All Manuals Search And Download.

Connections & Setup

��

�

��

�

��

AUDIO/VIDEO OUTPUT

��

�

��

�

��

�

��

�

��

�

��

�

��

�

��

�

��

�

��

�

��

Graphics contained within this publication are for representation only.

Chapter 1

Download from Www.Somanuals.com. All Manuals Search And Download.

Connections & Setup

TV + DVD + VCR

1. Connect your DVD Player to your TV.

A. Connect the audio (white and red) cables to the CMP1 L and R Audio jacks on the back of

the TV and to the Audio Output jacks on the DVD player.

B. Connect three video grade cables to the CMP1 Y PB PR jacks on the back of the TV and to

the Y PB PR jacks on the DVD player.

Notes:

If your DVD player does not have Y PB PR jacks, but does have an S-Video jack, connect the

player to the VID1 S-VIDEO jack on the TV using an S-Video cable.

If your DVD player does not have an S-Video jack, connect the player to the VID1 V (Video)

jack on the back of the TV using a video cable.

Important: If you use the VID1 S-VIDEO or V (Video) jack to connect your TV to the DVD

player, you must connect the audio cables to the VID1 L/MONO and R jacks on the TV.

2. Connect your VCR to your TV.

A. Connect a coaxial cable to the VCR’s antenna output and to the ANTENNA/CABLE Input

jack on the TV.

B. Connect the audio (white and red) cables to the VID2 L/MONO and R Audio jacks on the

back of the TV and to the Audio Output jacks on the VCR.

C. Connect the video cable to the VID2 V (Video) jack on the back of the TV and to the Video

Output jack on the VCR.

3. Make sure cable or antenna is connected to your VCR.

Connect the coaxial cable from your cable outlet or antenna to the antenna input on the VCR.

Go to page 15

Graphics contained within this publication are for representation only.

Chapter 1

Download from Www.Somanuals.com. All Manuals Search And Download.

Connections & Setup

TV+ A/V Receiver or Speakers

These are two different ways your TV uses a component to hear audio.

1. Connect audio cables to either the FIXED or VARIABLE AUDIO L and R OUTPUT jacks and

to the Audio Inputs on the A/V receiver.

• FIXED provides ﬁxed-level audio output from the TV. This audio output is ideal for

connecting to an A/V receiver that has its own volume control.

• VARIABLE provides variable-level audio output. Volume levels can be controlled by

the volume controls on the TV and TV remote control.

-OR-

2. Use speaker wire to connect the TV to external speakers.

• The EXT/INT switch beside the jacks let you turn the TV’s internal speakers on or

off. If you connect external speakers, slide the switch to EXT so the audio is sent to

the external speakers only. Choosing INT sends the audio to the TV’s speakers only.

Note: The external speaker rating is 8 ohms with 15 watts power handling capabilities.

��

�

��

�

��

�

AUDIO/VIDEO OUTPUT

��

Connect to either FIXED

�

��

�

��

�

��

�

��

�

��

VARIABLE Output

��

�

��

�

Graphics contained within this publication are for representation only.

Chapter 1

Download from Www.Somanuals.com. All Manuals Search And Download.

Connections & Setup

Explanation of Jacks (in alphabetical order)

This section describes the jacks you can use to make connections. There are several ways to

connect components to your TV.

ANTENNA/CABLE Lets you connect a coaxial cable to receive the signal from the

antenna, cable, cable box, or if using the examples on pages 6-11, a VCR.

��

AUDIO/VIDEO OUTPUT Lets you connect an ampliﬁer or audio receiver for improved

sound quality or an external video monitor.

AUDIO/VIDEO OUTPUT

��

�

•

FIXED AUDIO L/R Provides ﬁxed-level audio output from the TV. This audio

output is ideal for connecting an A/V receiver when you want to control the volume

through the A/V receiver.

��

�

•

VARIABLE AUDIO Provides variable-level audio output. Volume levels are

controlled by the volume controls on the TV and remote control.

SUBWOOFER Provides lower bass audio frequencies from the TV to a subwoofer.

Note: If you’ve connected a subwoofer, make sure you set the External Subwoofer

option in the Sound menu. Go to page 33 for instructions.

COMPONENT INPUTS Lets you connect a component video source, such as a DVD

player.

��

•

CMP1 Y PB PR (Component Video) Provides optimum picture quality because

the video is separated into three signals. Use three video-grade cables for the

connection. When using CMP1 Y PB PR, make sure to connect left and right audio

cables to the CMP1 L and R Audio Input jacks.

�

��

�

•

CMP1 L (Audio) Provides left audio connection. The left audio connector is

usually white.

��

�

CMP1 R (Audio) Provides right audio connection. The right audio connector is

usually red.

CMP2 Y PB PR, and L and R Audio Allows you to connect a second component

video source. Their description is the same as CMP1 above. When using CMP2 Y PB

PR, make sure you connect the left and right audio cables to the CMP2 Audio jacks.

COMPOSITE INPUTS Lets you connect another component such as a VCR, DVD

��

player, or laserdisc player. Its AUDIO jacks are the same as described for CMP1 above.

��

�

��

•

VID1 S-VIDEO Provides better picture quality than the video jacks (VID1 and 2

Video) because the color part of the picture is separated from the black and white

part of the picture. When using VID1 S-VIDEO, make sure to connect left and right

audio cables to the VID1 L/MONO and R Audio Input jacks.

��

�

•

VID1 V (Video) Provides composite video connection. The video connector is

usually yellow.

VID2 S-VIDEO, V and L/MONO and R Audio Allows you to connect a component

such as a VCR, DVD player, or laserdisc player. Their description is the same as

VID1 above.

Note: For each VID jack group (VID1 and VID2), you may connect either an S-Video

or Video cable. Do not connect both at the same time in either of the VID jack

groups.

Continues on next page...

Graphics contained within this publication are for representation only.

Chapter 1

Download from Www.Somanuals.com. All Manuals Search And Download.

Connections & Setup

DVI-HDTV Input Lets you connect an HDTV Tuner with a DVI output.

•

DVI (Digital Visual Interface) Provides an uncompressed, digital video interface

developed for high-bandwidth digital connection. It supports the overlay of high-

resolution graphics needed by some electronic program guide navigation and other

interactive services. DVI, when combined with HDCP (High bandwidth Digital

Content Protection) technology, creates a protected digital connection. The DVI-

HDTV connection is designed to display either progressive scan (480p) or HDTV

(1080i) signals at a bandwidth of up to 1.78 Gigabits per second.

�

��

�

•

L (Audio) Provides left audio connection when using the DVI jack. The left audio

connector is usually white.

R (Audio) Provides right audio connection when using the DVI jack. The right

audio connector is usually red.

Note: Remember to connect the left and right audio cables because the DVI cable

carries only the picture signal, not the sound.

EXTERNAL SPEAKERS

•

Right and Left Speaker Terminals Let you connect external left and right

speakers to the TV to receive left and right sound.

��

•

EXT/INT (switch) Lets you turn the TV’s internal speakers on or off. EXT sends

audio to external speakers only. INT sends audio to the TV’s internal speakers

only.

Wired IR This jack is for connecting a wired remote control system, which is

primarily for professional installers. If you’re using the remote that was included with

your TV, don’t plug anything into this jack.

��

The Front of Your TV

Front Input Jacks

The TV has front inputs for convenience: one set of audio/video input jacks, an S-Video jack and a headphones jack. The

jacks are ideal for using a video game console or a camcorder. Locate the jacks either on the front of the TV or on one of

the sides. To access the component you connected to the front of the TV, press the INPUT button on your remote until

FRNT appears on the screen.

Note: When connecting a component that uses a monaural cable, such as some camcorders, use the Left (mono) input

jack to get sound from both speakers.

PHONES Allows you to connect headphones to listen to the sound coming from the TV. To adjust volume control of

the headphones, press the VOL > or VOL < button (the volume display appears). Press the arrow up or down button (the

headphone volume display appears), then press the right or left arrow button to adjust the headphone volume.

VIDEO (in) Receives video from another component such as a camcorder, video game console or VCR.

L/MONO and R AUDIO Receives audio from another component such as a camcorder, video game console or VCR.

S-VIDEO (in) Allows you to connect an S-Video cable from another component. Make sure you also connect audio cables

from the component to the TV.

Note: Do not connect an S-Video and a regular video cable to the FRNT jacks at the same time.

Graphics contained within this publication are for representation only.

Chapter 1

Download from Www.Somanuals.com. All Manuals Search And Download.

Connections & Setup

Front Panel Buttons

If you cannot locate your remote, you can use the front panel buttons of your TV to operate many of the TV’s features.

MENU/OK Brings up the Main menu. In the menu system, it selects highlighted items.

Scans down through the current channel list. In the menu system, acts like down arrow button on the remote control

and adjusts menu controls.

Scans up through the channel list. In the menu system, acts like up arrow button on the remote control and adjusts

menu controls.

VOL < Decreases the volume. In the menu system, acts like left arrow button on the remote control and adjusts menu

controls.

VOL > Increases the volume. In the menu system, acts like right arrow button on the remote control and adjusts menu

controls.

POWER Turns the TV on and off.

Plug in the TV

Plug the end of the power cord into a grounded wall outlet. Insert the plug

completely into the outlet.

Put batteries in the remote

•

Remove the battery compartment cover from the back of the remote by

pushing the tab and lifting off the cover.

Insert two fresh batteries. Make sure the polarities (+ and -) are aligned

correctly.

Replace the cover.

How to Use the Remote Control to

Complete the Initial Setup

The technical term is “Navigation” – how you move through the on-screen menus.

The theory is the same throughout the menu screens: highlight your choice and

select it.

��

TV button

��

button

��

To highlight a menu item, press the arrow buttons on the remote to highlight one

of the items listed on the screen. Use the up or down arrow button to move up or

down. Use the right or left arrow button to move right or left.

��

Arrows

To select the item that you’ve highlighted, press OK.

Note: Highlighted means that the menu item stands out from other menu

items on the list (appears darker, brighter, or a different color).

Graphics contained within this publication are for representation only.

Chapter 1

Download from Www.Somanuals.com. All Manuals Search And Download.

Connections & Setup

Turn on the TV

Press TV on the remote, or press POWER on the TV’s front panel.

Note: Pressing the TV button not only turns on the TV, but puts the

remote into TV mode. “TV mode” means that the buttons on the remote

control operate the TV’s functions.

Tip

Complete the Initial Setup

The menu system in your TV allows the TV’s features to work properly. The

ﬁrst time you turn on your TV, the setup screens appear.

To access the setup menus manually, press

MENU and choose SETUP.

Set the Menu Language

The ﬁrst part of the setup allows you to select your preferred language for the

menu system.

If English is your preferred language, press OK. If you want to choose another

language, press the down arrow button until that language is highlighted, and

press OK.

Complete Auto Channel Search

The next screen asks you to make sure you've connected the TV to a cable,

satellite, or off-air signal. When you're sure that a signal is connected to your

TV, press OK on your remote to go to the Channel setup screen.

In the Channel setup screen, you can launch the Auto channel search by

pressing OK. The Auto channel search allows the TV to search for all channels

viewable through your antenna or cable TV system. This is sometimes called

auto programming. When the channel search is complete, press OK to access

the List & Labels screen.

Graphics contained within this publication are for representation only.

Chapter 1

Download from Www.Somanuals.com. All Manuals Search And Download.

Connections & Setup

Changing Lists and Labels

The List & Labels part of the setup lets you edit your channel list and choose or

create a personal six-character label for each channel.

Note: Changing List and Labels can be time consuming. You can change

these at a later time by accessing the Setup menu.

1. Press the left or right arrow to scroll through the channels and choose the

one you want to edit.

2. Press the down arrow to highlight the In channel list option. Press the left

or right arrow button to add (the box is checked) or remove (the box is

unchecked) the channel from the list.

3. Press the down arrow to highlight the Channel label option. Press the left

or right arrow button to scroll through the available list of 25 most common

labels. The last option in the list allows you to create your own six-

character label for the channel (the ﬁrst letter of the label is highlighted).

4. Press the 1 or 2 number button to change the ﬁrst letter of the label.

5. Press the right arrow to highlight the second letter, then press the 1 or 2

number button to change the second letter, etc...

6. When you are ﬁnished creating your label, press OK. Select Go back to go

to the Auto Convergence menu.

Auto Convergence

Your TV’s picture tubes might have been disturbed during delivery or after you

moved the TV, causing the color in your TV to be out of alignment. The colors

adjust by starting auto convergence.

IMPORTANT: Auto convergence works best once the TV has warmed up

for at least an hour. If you've just unpacked your TV, it's a good idea to

repeat the Auto convergence function when the TV's been running for at

least an hour. See page 38 for more information about Auto convergence.

1. Press OK to begin auto convergence.

2. When the auto convergence is complete, the Red center convergence menu

appears. The cross in the middle of the screen should be yellow. If it is not,

use the arrow buttons to move the red cross to overlap the green cross.

Press OK when adjustments are complete.

Note:

If you're using an HD source (such as an

HDTV tuner or HDTV satellite receiver) on the

CMPNT or DVI input, you should run Auto

convergence separately for that input as well.

Tune to the input you're using for the HD

source, then go to page 38 for information

on Auto convergence.

3. The Blue center convergence menu appears with a cyan cross in the middle

of the screen. If it is not, use the arrow buttons to move the blue cross

to overlap the green cross. Press OK (the TV tunes to the last selected/

available channel in the channel list).

Graphics contained within this publication are for representation only.

Chapter 1

Download from Www.Somanuals.com. All Manuals Search And Download.

Using the Remote Control

Indicator

The Buttons on the Remote Control

(0-9) Number Buttons Enter channel numbers and time settings directly

through the remote control.

To enter a one-digit channel, enter a zero ﬁrst. To enter a two-digit channel,

press the two digits. To enter a three-digit channel, press and hold the 1 button

until 1 and two dashes (– –) appear, then add the second two digits. Example:

to tune to channel 123, press and hold 1 until 1– – appears, release the 1 button

and then press 2 and 3.

��

ANTENNA In VCR mode (if programmed), this button works as a TV/VCR

button for some VCRs. In SAT mode (if programmed), this button works as a

TV/SAT button for some satellite receivers.

��

Arrows Used to highlight different items in the TV menu and to adjust the

menu controls. The up and down arrows move the PIP window when no

menus are on the screen. When watching TV without the PIP window or

menu system in use, the left and right arrows (ZOOM– and ZOOM+) change

the current format of the screen (4:3, Zoom 14:9, Zoom 16:9, Zoom 16:9 ^/v,

Cinerama, regular mode 16:9).

��

AUX•HD Puts the remote in AUX/HD mode. As a default, this button controls

some models of RCA HDTV Tuners. It can also be programmed to operate

some brands of an additional remote-controllable components. The Autotuning

feature for this button works only with HDTV tuners (see page 24 for more

information on Autotuning).

��

CH + or CH - Scans up or down through the current channel list. Press once

to change the channel up or down; press and hold to continue changing

channels. In DVD mode (if programmed), these buttons work as chapter

advance or chapter reverse buttons with some DVD players.

CLEAR Removes any menu or display from the screen and returns you to

normal viewing. Also exits PIP or POP if no menu is displayed.

��

DVD Puts the remote in DVD mode and, if Autotuning is enabled, will turn on

the TV and tune to the correct input channel.

��

FREEZE When watching TV, freezes the picture until you press any button

on the remote to resume normal TV viewing. The FREEZE feature automatically

times out after a short time. Please note that when you "unfreeze" you go back

to live programming (skipping any programming that occurred during the

freeze).

��

Note: The FREEZE feature does not work on signals from the DVI-HDTV, CMP1

or CMP2 inputs in progressive scan (480p) or HDTV (1080i) modes.

Do not use the Freeze feature for an extended period of time. This can cause

the image to be permanently imprinted on the picture tube. Such damage is

not covered by your warranty. Press any button to unfreeze the picture at any

time.

GO BACK Returns you to the previous channel.

GUIDE Brings up the Channel Guide menu.

Indicator Indicates the programming mode when programming the remote

to control components. The indicator lights up when you press a valid button

on the remote. It ﬂickers when the remote batteries are low and you press a

button.

Chapter 2

Graphics contained within this publication are for representation only.

Download from Www.Somanuals.com. All Manuals Search And Download.

Using the Remote Control

INFO Brings up channel banner; press again to clear the screen.

Tip

INPUT Press to toggle through the available input sources (VID1, VID2, FRNT,

CMP1, CMP2 and DVI. Press the CH+ or CH- button to resume TV viewing).

The indicator ﬂashes when the remote

batteries are low and you press a button on

the remote.

MENU Brings up the Main menu.

A warning banner may also appear on the

screen when you press a remote button and

your batteries are low.

MUTE Reduces the TV’s volume to its minimum level. Press again to restore

the volume.

OK When in the menu system, selects highlighted items. When watching

TV, freezes the picture until you press any button on the remote to resume

normal TV viewing. Please note that when you "unfreeze" you go back to live

programming (skipping any programming that occurred during the freeze).

Tip

To turn off all the RCA, GE, and Proscan

components that are connected to the TV,

press ON•OFF twice within two seconds.

ON•OFF When in TV mode, turns the TV on and off. If in another component

mode (DVD or AUX•HD) and programmed, will turn the component on and

off. When pressed twice within two seconds, the ON•OFF button turns off most

RCA, GE and Proscan components.

This feature only works with most RCA, GE,

and Proscan products.

PIP Press once to bring up the small picture-in-picture window. Press again to

bring up the picture-outside-picture (POP) windows. Press to remove POP. (See

Chapter 3 for more information about using PIP.)

PIP + or PIP – When using PIP or POP, changes the channel in the picture

window.

PRESETS Displays the Picture and Sound preset settings. Use the up and down

arrow buttons to highlight either Picture or Sound settings. Use the left and right

arrow buttons to change to a different Picture or Sound preset.

Note:

The DVD and AUX•HD buttons also turn on

most RCA, GE, and Proscan products.

REVERSE, PLAY, FORWARD, RECORD, STOP, PAUSE If programmed,

provides transport control for some remote-controllable VCRs and DVD players.

SKIP Press once before changing channels and the TV will wait 30 seconds

before returning you to the original channel. Press repeatedly to add more time.

TV Turns on the TV and puts the remote in TV mode. Also displays current

status.

VOL – or VOL + Decreases or increases the TV’s volume.

Chapter 2

Graphics contained within this publication are for representation only.

Download from Www.Somanuals.com. All Manuals Search And Download.

Using the Remote Control

Programming the Remote to Operate

Other Components

Indicator

The universal remote can be programmed to operate most brands of remote

controllable components. The remote is already programmed to operate most

RCA, GE, and Proscan components.

Also, the AUX•HD button can be programmed to operate most brands of an

additional remote-controllable component (such as a VCR, DVD player, satellite

receiver or cable box).

Note: The TV button can’t be programmed on this remote.

Find Out If You Need to Program the Remote

To determine whether the universal remote needs to be programmed to operate

one of the components connected to your TV, such as a DVD player, do the

following:

1. Turn on the component (in this example, a DVD player).

2. Point the remote at the component.

3. Press the corresponding component button (in this example, the DVD

button).

4. Press ON•OFF to see if the DVD player responds. If the DVD player

doesn’t respond, you need to program the remote to operate it.

You’ll use these buttons when

you program the remote.

Programming the Remote

There are two ways to program the remote control:

Important: The remote may not

be compatible with all models of

all brands of components. It also

may not operate all functions of

the remote that came with your

component.

•

automatic code search

direct entry

Using Automatic Code Search

The following instructions can be used to program the remote to operate each

of your components. If you want to stop the automatic code search without

programming any of your components, press CLEAR until the indicator on the

remote turns off.

Note: The AUX•HD button on this remote is set by default to search

for codes for DVD players only. If you want to program it for use with a

different component, use the direct entry method.

1. Turn on the component you want to operate (VCR, DVD player, etc.)

2. Press and hold the component button you want to program (DVD or

AUX•HD). While holding the component button, press and hold ON•OFF

until the indicator on the remote turns on, then release both buttons.

Tip

3. Point the remote at the component. Press and release PLAY, then wait 5

seconds or until the indicator on the remote stops ﬂashing.

To stop the automatic code search without

programming any components, press and hold

CLEAR until the indicator on the remote turns

off.

At this point the remote is searching for the correct code to program. If,

after 5 seconds, the component you want to operate does not turn off,

press PLAY again to tell the remote to search the next set of codes.

Chapter 2

Graphics contained within this publication are for representation only.

Download from Www.Somanuals.com. All Manuals Search And Download.

Using the Remote Control

Continue pressing PLAY until the component turns off or the indicator light

on the remote turns off. If the indicator light turns off, then all codes for that

particular component have been tested once. If the component does not turn

off, then the remote can’t be programmed to operate that component.

If the component you want to control does turn off:

1. Press and release REVERSE, then wait 2 seconds. Repeat this step until the

device turns back ON.

2. To ﬁnish, press and hold STOP until the indicator on the remote turns off.

A code that controls your component has been saved to that remote button.

Using Direct Entry

1. Turn on the component to be programmed.

Important

You must continue pressing the component

button while you enter the code.

2. Look up the brand and code number(s) for the component on the code list

in this section.

Let’s say you have a Zenith DVD player. To

program the universal remote to operate the

DVD player, you would:

3. Press and hold the component button you want to program on the remote.

4. Enter the code from the remote control code list on the following pages. If

the indicator ﬂashes, you have either entered an invalid code or the button

isn’t programmable.

Press and hold the DVD button while you

enter the ﬁrst code listed for Zenith in the

DVD Codes column.

5. Release the component button, point the remote at the component and

then press ON•OFF to see if the component responds to the command. If it

doesn’t, try pressing the component button and then ON•OFF again.

Release the DVD button. Press ON•OFF to

see if the DVD player responds. If it doesn’t,

follow the same steps, but enter the second

code for Zenith DVD players instead of the

ﬁrst.

•

If you get no response, repeat these steps using the next code listed for

your brand, until the component responds to the remote commands.

•

If you try all the codes for your component brand and none work, try the

automatic code search method. If automatic code search doesn’t ﬁnd the

code, the remote is not compatible with your component.

Chapter 2

Graphics contained within this publication are for representation only.

Download from Www.Somanuals.com. All Manuals Search And Download.

Using the Remote Control

Component buttons

How to Use the Remote After You’ve Programmed It

Because this universal remote can control several different components (TV,

DVD, VCR, satellite receiver, etc.) it uses operational modes triggered by the

component buttons. For example, if you want the remote to control the TV, you

would press the TV button to put the remote into TV mode before you could

control the TV.

��

�

��

1. Press the appropriate component button (DVD or AUX•HD) to set the

remote to control the component.

2. Press ON•OFF to turn the component ON or OFF.

3. Use the remote buttons that apply to that component.

Notes:

•

The remote may not be compatible with all brands and models of

components. It also may not operate all functions of the remote that

came with your component.

•

If you keep pressing buttons and nothing happens, the remote is

probably in the wrong mode. You must press the component button

that matches the component you want to operate (i.e., if you want to

operate the DVD player, press DVD on the remote control to put the

remote in DVD mode.)

Using the INPUT Button

Use the INPUT button to scroll through the available input channels and view

components you have connected to the TV.

1. Press TV to place the remote in TV mode. Make sure the component you

want to view is turned ON.

2. Press INPUT to tune to an available input channel.

3. To return to the channel you were previously watching on TV, press CH+ or

CH- button.

Chapter 2

Graphics contained within this publication are for representation only.

Download from Www.Somanuals.com. All Manuals Search And Download.

Remote Control Codes

Olympus ...................................................................... 2021

VCR Codes

Programmable for the AUX•HD button.

Cable Box Codes

Programmable for the AUX•HD button.

Optimus ............................................................. 2014, 2132

Optonica ...................................................................... 2096

Panasonic....................2021, 2022, 2109, 2125, 2126, 2127

Pentax ...................................2016, 2055, 2056, 2107, 2120

Pentex Research .......................................................... 2018

Philco ..............................................2021, 2022, 2062, 2063

Philips .............................................2021, 2062, 2096, 2124

Pilot.............................................................................. 2014

Pioneer..................................2010, 2055, 2080, 2081, 2123

Portland...........................................2016, 2017, 2019, 2110

Proscan..................................................... 2000, 2001, 2131

Protec........................................................................... 2061

Pulsar ........................................................................... 2104

Quarter......................................................................... 2011

Quartz .......................................................................... 2011

Quasar...................................................... 2021, 2022, 2125

RCA ........2000, 2001, 2003, 2013, 2021, 2055, 2056, 2082,

2083, 2084, 2085, 2086, 2087, 2088, 2089,

Admiral......................................................................... 2132

Adventura .................................................................... 2026

Aiko.............................................................................. 2027

Aiwa............................................................................. 2026

Akai.........2003, 2004, 2005, 2007, 2008, 2111, 2112, 2113

American High............................................................. 2021

Asha ............................................................................. 2013

Audio Dynamics................................................ 2009, 2010

Audiovox ..................................................................... 2014

Bell & Howell.............................................................. 2011

Beaumark..................................................................... 2013

Broksonic........................................................... 2012, 2025

Calix ............................................................................. 2014

Candle...............2013, 2014, 2015, 2016, 2017, 2018, 2019

Canon....................................................... 2021, 2022, 2114

Capehart............................................................. 2020, 2110

Carver........................................................................... 2062

CCE..................................................................... 2027, 2061

Citizen ...2013, 2014, 2015, 2016, 2017, 2018, 2019, 2027

Colortyme .................................................................... 2009

Colt............................................................................... 2061

Craig................................................2013, 2014, 2023, 2061

Curtis-Mathes.......................2000, 2009, 2013, 2016, 2018,

2021, 2022, 2024, 2115, 2131

Cybernex...................................................................... 2013

Daewoo...2015, 2017, 2019, 2025, 2026, 2027, 2028, 2110

Daytron........................................................................ 2110

DBX.................................................................... 2009, 2010

Dimensia............................................................ 2000, 2131

Dynatech...................................................................... 2026

Electrohome....................................................... 2014, 2029

Electrophonic............................................................... 2014

Emerson.....................2012, 2014, 2015, 2021, 2024, 2025,

2026, 2029, 2030, 2031, 2032, 2033, 2034,2035, 2036,

2037, 2038, 2039, 2040, 2041, 2042,2044, 2045, 2046,

2047, 2065, 2113, 2116, 2117, 2130

Fisher.......2011, 2023, 2048, 2049, 2050, 2051, 2052, 2118

Fuji...................................................................... 2021, 2119

Funai ............................................................................ 2026

Garrard......................................................................... 2026

GE ..................................................2000, 2001, 2013, 2021,

2022, 2053, 2115, 2120, 2131

Goldstar...........................................2009, 2014, 2018, 2054

Gradiente ..................................................................... 2026

Harley Davidson.......................................................... 2026

Harman Kardon........................................................... 2009

Harwood...................................................................... 2061

Headquarter................................................................. 2011

Hitachi...............2055, 2056, 2057, 2107, 2111, 2120, 2122

Hi-Q ............................................................................. 2023

Instant Replay.............................................................. 2021

JCL................................................................................ 2021

JC Penney ........2009, 2010, 2011, 2013, 2014, 2021, 2022,

2055, 2056, 2058, 2059, 2060, 2107, 2118

Jensen....................................................... 2055, 2056, 2111

JVC ..............................2009, 2010, 2011, 2018, 2111, 2123

Kenwood ..........2009, 2010, 2011, 2016, 2018, 2111, 2123

KLH .............................................................................. 2061

Kodak................................................................. 2014, 2021

Lloyd ............................................................................ 2026

Logik ............................................................................ 2061

LXI................................................................................ 2014

Magnavox ......................................2021, 2022, 2062, 2063,

2104, 2105, 2108, 2124

Magnin ......................................................................... 2013

Marantz ...2009, 2010, 2011, 2016, 2018, 2021, 2062, 2064

Marta ............................................................................ 2014

Masushita ..................................................................... 2021

Mei ............................................................................... 2021

Memorex........................................2011, 2013, 2014, 2021,

2023, 2026, 2104, 2132

MGA......................................................... 2029, 2065, 2113

MGN Technology ........................................................ 2013

Midland........................................................................ 2053

Minolta..................................................... 2055, 2056, 2107

Mitsubishi.........2029, 2055, 2056, 2065, 2066, 2067, 2068,

2069, 2070, 2071, 2072, 2073, 2074, 2106, 2113, 2123

Montgomery Ward............................................. 2075, 2132

Motorola............................................................. 2021, 2132

MTC.................................................................... 2013, 2126

Multitech ...............................2013, 2016, 2026, 2053, 2061

NEC ............................2009, 2010, 2011,2016, 2018, 2064,

2076, 2078, 2079, 2111, 2123

ABC.......................................5002, 5003, 5004, 5006, 5053

Antronix............................................................. 5008, 5009

Archer....................................................... 5008, 5009, 5010

Cabletenna................................................................... 5008

Cableview .................................................................... 5008

Colour Voice...................................................... 5012, 5013

Comtronic .................................................................... 5014

Contec.......................................................................... 5016

Eastern ......................................................................... 5017

GC Electronics............................................................. 5009

GE ...................................................................... 5000, 5001

Gemini ............................................................... 5018, 5019

General Instrument ..................................................... 5003

Hamlin ........................5020, 5021, 5022, 5028, 5035, 5045

Hitachi.......................................................................... 5003

Jerrold .........................5003, 5018. 5023, 5024, 5046, 5053

Magnavox .................................................................... 5025

Memorex...................................................................... 5026

Movie Time.................................................................. 5027

NEC .............................................................................. 5005

NSC............................................................................... 5027

Oak..................................................................... 5016, 5029

Panasonic........................................................... 5048, 5052

Philips ............................................5011, 5012, 5013, 5015,

5019, 5025, 5030, 5031, 5032

Pioneer............................................................... 5033, 5034

Proscan............................................................... 5000, 5001

RCA .................................................5007, 5047, 5049, 5052

Realistic........................................................................ 5009

Regal .................................................................. 5022, 5035

Regency........................................................................ 5017

Rembrandt ................................................................... 5003

Samsung....................................................................... 5034

Scientiﬁc Atlanta.............................5006, 5036, 5037, 5038

Signal............................................................................ 5018

Signature...................................................................... 5003

Sprucer......................................................................... 5052

Standard Components....................................... 5039, 5044

Starcom .............................................................. 5018, 5053

Stargate......................................................................... 5018

Starquest....................................................................... 5018

Tocom................................................................ 5004, 5023

Tusa.............................................................................. 5018

TV86............................................................................. 5027

Unika.................................................................. 5008, 5009

United Cable................................................................ 5053

Universal.................................................. 5008, 5009, 5010

Viewstar ............................................................. 5025, 5027

Zenith................................................................. 5050, 5051

2090, 2091, 2107, 2115, 2120, 2125, 2131, 2133

Radioshack/Realistic ...........2011, 2013, 2014, 2021, 2022,

2023, 2026, 2029, 2049, 2050, 2096, 2132

Radix ............................................................................ 2014

Randex......................................................................... 2014

Ricoh............................................................................ 2128

Runco........................................................................... 2104

Samsung......................2005, 2013, 2015, 2033, 2053, 2112

Sanky.................................................................. 2104, 2132

Sansui..............................................2010, 2092, 2111, 2123

Sanyo........................................................ 2011, 2013, 2023

Scott.........2012, 2015, 2025, 2032, 2038, 2065, 2093, 2116

Sears...........................2011, 2014, 2021, 2023, 2048, 2049,

2050, 2051, 2055, 2056, 2107, 2118

Sharp.................2017, 2029, 2094, 2095, 2096, 2097, 2132

Shintom...........................................2004, 2056, 2061, 2098

Shogun......................................................................... 2013

Signature...................................................................... 2132

Singer ....................................................... 2021, 2061, 2128

Sony ................................................2004, 2098, 2099, 2119

STS...................................................................... 2021, 2107

Sylvania.............2021, 2022, 2026, 2062, 2063, 2065, 2124

Symphonic................................................................... 2026

Tandy ........................................................................... 2011

Tashiko......................................................................... 2014

Tatung.......................................................................... 2111

TEAC ........................................................ 2026, 2085, 2111

Technics............................................................. 2021, 2109

Teknika .................................2014, 2021, 2026, 2100, 2129

TMK.......................................................... 2013, 2024, 2047

Toshiba..............2015, 2049, 2051, 2055, 2065, 2093, 2116

Totevsion ........................................................... 2013, 2014

Unitech......................................................................... 2013

Vector Research..............................2009, 2010, 2015, 2016

Victor............................................................................ 2010

Video Concepts ....................2009, 2010, 2015, 2016, 2113

Videosonic ................................................................... 2013

Wards .....2013, 2014, 2015, 2021, 2023, 2026, 2029, 2055,

2056, 2061, 2096, 2101, 2102, 2103, 2107, 2116, 2132

XR-1000.................................................... 2021, 2026, 2061

Yamaha .................................2009, 2010, 2011, 2018, 2111

Zenith....................................2004, 2098, 2104, 2119, 2128

Satellite Receiver Codes

Programmable for the AUX•HD button.

Alphastar...................................................................... 5079

Chapparal........................................................... 5056, 5057

Dishnet......................................................................... 5078

Drake ................................................................. 5058, 5059

Echostar ....................................................................... 5089

GE ..............................................5000 (SAT1), 5001 (SAT2)

General Instruments................................ 5060, 5061, 5062

Hitachi................................................................ 5083, 5084

Hughes Network ............................................... 5077, 5090

JVC ............................................................................... 5082

Panasonic..................................................................... 5075

Philips .......................................................................... 5085

Primestar...................................................................... 5076

Proscan.......................................5000 (SAT1), 5001 (SAT2)

RCA ..............5000 (SAT1), 5001 (SAT2), 5071, 5080, 5081

Realistic........................................................................ 5063

Sony ............................................................................. 5072

STS1.............................................................................. 5064

STS2.............................................................................. 5065

STS3.............................................................................. 5066

STS4.............................................................................. 5067

Toshiba............................................................... 5068, 5073

Uniden ............................................................... 5069, 5086

DVD codes

Programmable for the DVD and AUX•HD buttons.

Aiwa............................................................................. 3009

Apex................................................................... 3023, 3024

GE ................................................................................ 3000

Hitachi.......................................................................... 3008

JVC ..................................................................... 3002, 3010

Konka................................................................. 3011, 3012

Magnavox .................................................................... 3003

Mitsubishi..................................................................... 3004

Panasonic..................................................................... 3013

Philips .............................................3003, 3019, 3021, 3022

Pioneer......................................................................... 3005

Proscan......................................................................... 3000

RCA .................................................................... 3000, 3001

Samsung....................................................................... 3025

Sanyo............................................................................ 3014

Sony ......................................................... 3006, 3015, 3016

Toshiba..................................................... 3007, 3017, 3020

Zenith........................................................................... 3018

HDTV Tuner Codes

Programmable for the AUX•HD button.

RCA .............................................................................. 7000

Nikko ........................................................................... 2014

Noblex.......................................................................... 2013

Chapter 2

Graphics contained within this publication are for representation only.

Download from Www.Somanuals.com. All Manuals Search And Download.

Using the TV’s Features

Channel Banner

There are several indicators that might appear when you press the TV or INFO button on the

remote. This display is called the Channel Banner. The following list describes the items on the

Channel Banner screen (left to right and top to bottom).

4/3 format

Current screen format.

Mono

(or Stereo)

Mono appears when the current channel is broadcasting in

mono. Stereo appears when the current channel is broadcasting

in stereo.

SAP

The current channel is broadcasting SAP (Second Audio

Program) information.

Parental Controls are locked.

Sample displays on a Channel Banner.

Closed Captioning is available on the current channel.

Current time.

03:45 pm

15 NBC

Current channel and label assigned to the channel.

Commercial Shows the time remaining on the commercial skip (SKIP)

skip 0:30

timer.

Sound is muted.

Autotuning

The autotuning feature automatically tunes the TV to the correct channel/input for different

components you have connected to your TV (like a VCR, DVD Player, etc.) When you set up

autotuning in the menu system you don’t have to remember to change your TV to the VID1

input, for example, when you want to watch a DVD on your DVD player.

Why You Should Use the Autotuning Feature

��

With the autotuning feature, you can set up the TV to tune to the channel/input

��

you need to watch by pressing that component’s button.

Your remote's component buttons

Chapter 3

Graphics contained within this publication are for representation only.

Download from Www.Somanuals.com. All Manuals Search And Download.

Using the TV’s Features

How to Set Up the Autotuning Feature

The way you set up the autotuning feature in the TV’s menu corresponds to the component

buttons on the remote and the way you have each component connected to your TV. When you

set up autotuning, you’re telling the TV what channel/input to tune to when you press the DVD or

AUX•HD button on the remote control.

1. Press MENU (the MAIN MENU appears).

2. Highlight Setup and press OK on your remote control.

3. Highlight Autotuning and press OK.

4. Choose which component button you would like to set:

Set DVD Channel Lets you set up the channel the TV tunes to when you

press the VCR button.

Set AUX/HD Channel Lets you set up the channel the TV tunes to when

you press the AUX/HD button.

5. Press the right arrow button to select the choice that matches the way you

have the component connected to this TV, and press OK.

You can select from the following inputs or channels:

N/A Choose this if you don’t have this particular component connected

to the TV, or if you don’t want the TV to automatically tune to the correct

channel/input when you’re using this component.

Channel 3 or 4 Component is connected to the CABLE/ANTENNA jack on

the back of the TV, and you want the TV to tune to channel 3 when you

press the corresponding button on the remote. Reminder: make sure the

component’s Channel 3/4 switch is set to channel 3.

VID1 or VID2 (Video Input) Component is connected to a VIDEO or

S-Video jack on the back of the TV and you want the TV to tune to a VID

input channel when you press the corresponding component button.

FRNT (Front Video Input) Component is connected to the VIDEO jack

on the front of the TV and you want the TV to tune to the front VID input

channel (FRNT) when you press the corresponding component button.

CMP1 or CMP2 (Component Video Input) Compatible component video

source, such as a DVD player or digital TV converter box, is connected to the

three COMPONENT VIDEO INPUT jacks (Y,PB,PR) on the back of the TV and

you want the TV to tune to the component video input channel (CMP) when

you press the corresponding component button.

DVI Component is connected to the DVI-HDCP jack on the back of the TV

and you want the TV to tune to the DVI input channel when you press the

corresponding component button.

Chapter 3

Graphics contained within this publication are for representation only.

Download from Www.Somanuals.com. All Manuals Search And Download.

Using the TV’s Features

Parental Controls and V-Chip

The choices in the US V-CHIP and Canada V-CHIP menus involve software inside your TV

(referred to as V-Chip) which allows you to block TV programs and movies based on violence,

sex, or other content you may believe children should not view.

Once you block programs, you can unblock programs by entering a password.

By default, the software inside your TV is turned “off.” For instructions to turn on V-Chip, go to

page 31.

Note: Parental Control settings are not available for DVI, CMP1, or CMP2 inputs.

How V-Chip Works for USA and Canada

V-Chip reads the program’s age-based rating (TV-MA, TV-14, etc.) and content themes [(Violence

(V), Adult Language (L), etc.)]. If you have blocked the rating and/or content themes that the

program contains, you will receive the message This channel has not been approved for viewing.

Change channel or press OK to enter password and temporarily deactivate the Parental Control.

Broadcasters are not required to provide content themes, so programs received with no content

themes will only be blocked if you block their age-based rating. You can also block out programs

that have been given an Exempt rating, and programs that are considered unrated. The next

several pages have tables showing the TV age-based ratings and content themes for the US and

Canada.

US V-Chip TV Rating Limit

The V-Chip TV Rating Limit lets you decide which TV programs can and cannot

be viewed.

To set TV programming limits:

1. Choose Parental Control from the MAIN MENU. If Parental Controls have

previously been locked, you must enter your password.

2. Highlight and select US V-Chip. Then select V-Chip TV Rating.

3. Once you get to the V-Chip TV rating limit screen, use the arrow buttons

and OK on your remote to change the status of a TV program rating or

content theme from View to Block.

4. For TV rating limits to take effect, lock Parental Controls by accessing the

Lock parental controls menu.

The following sections give you more details about how to change the status of

TV program limits.

Note: If you forget your password, follow step one above to get to the

password entry screen. Then press the VOL+ and CH+ buttons on the TV's

front panel at the same time for at least 8 seconds. You will receive an

on-screen message that Parental Controls have been unlocked once you've

successfully reset the password.

Chapter 3

Graphics contained within this publication are for representation only.

Download from Www.Somanuals.com. All Manuals Search And Download.

Using the TV’s Features

The V-Chip Rating Screen

The following is an example of where items are located within the Rating Limit screen.

Rating Status Field

Lets you select whether the status of the age-based rating limit to

the left is View or Block.

Content Themes

Lists the content themes you can block or

view.

Rating Field

Content Status Fields

Lets you select from a

list of age-based ratings

you can block or view.

Lets you select which content themes to

view for the selected rating, and whether

the status of the content theme is currently

unlocked ( ) or locked ( ).

Rating Settings Area

Lets you see the current block/view state of age-based ratings and as-

sociated content. The View ( ) settings are coded in green, and the

Block ( ) settings are coded in red.

Age-Based

USA Description and Content Themes for Age-Based Ratings

Rating

Mature Audience Only. Speciﬁcally designed to be viewed by adults and may be unsuitable for

children under 17. It contains one or more of the following content themes: crude indecent language

(L), explicit sexual activity (S), or graphic violence (V).

TV-MA

Parents Strongly Cautioned. Contains some material that many parents would ﬁnd unsuitable for

children under 14. Parents are strongly urged to exercise greater care in monitoring this program and

are cautioned against letting children under the age of 14 watch unattended. This program contains

one or more of the following content themes: intensely suggestive dialogue (D), strong coarse

language (L), intense sexual situations (S), or intense violence (V).

TV-14

Parental Guidance Suggested. Contains material that parents may ﬁnd unsuitable for younger

children. Many parents may want to watch it with their younger children. The program contains one

or more of the following content themes: some suggestive dialogue (D), infrequent coarse language

(L), some sexual situations (S), or moderate violence (V).

TV-PG

TV-G

General Audience. Most parents would ﬁnd this program suitable for all ages. It contains little or no

sexual dialogue (D) or situations (S), no strong language (L), and little or no violence (V).

Directed to Children 7 years and older. Designed for children ages 7 and above. It may be more

appropriate for children who have acquired the developmental skills needed to distinguish between

make-believe and reality. Themes and elements in this program may include mild fantasy violence

(FV) or comedic violence, or may frighten children under the age of 7.

TV-Y7

TV-Y

All Children. Themes and elements in this program are designed for a young audience, including

children from ages 2-6. It is not expected to frighten younger children.

Chapter 3

Graphics contained within this publication are for representation only.

Download from Www.Somanuals.com. All Manuals Search And Download.

Using the TV’s Features

Blocking Age-Based Ratings

You can automatically block all program ratings above a speciﬁed age-

based rating level. To block programs with higher ratings:

1. Press the up or down arrow button to scroll to the rating

corresponding with the lowest rating you do not want the child to

watch.

2. Press the OK button to toggle between View and Block. The status

for the rating listed to the left and all higher ratings automatically

changes to Block (and ).

3. Use the up/down arrow buttons to highlight Go back and press OK.

4. Select Lock Parental Controls from the Parental Control menu for

rating limits to take effect.

Viewing Age-Based Ratings

After you block age-based ratings, you can change some of the ratings

back to View.

Hierarchy of Age-Based Ratings

Mature Audience Only

TV-MA

TV-14

TV-PG

TV-G

Parents Strongly Cautioned

Parental Guidance Suggested

General Audience

1. Use the up/down arrows to select the rating with a status of Block.

2. Press OK to select View.

TV-Y7

TV-Y

Directed to Children 7 years and older

All Children

Blocking Speciﬁc Content Themes

Content Themes

Sexually explicit dialogue

Adult language

You can block programs based on their content. (Content is represented

by the D, L, S, V and FV on your screen.) When you block a content

theme for a particular rating, you automatically block that content theme

for higher rated programs as well.

Sexual situations

Violence

To block program content:

1. Determine the content themes you want to block.

Fantasy Violence

2. Press the down arrow button to scroll to the rating whose content

theme you want to change.

3. Press the right arrow button to move the yellow highlight to a

particular content theme status.

4. Press the OK button to change its status to . (In the example to

the left, you block the language (L) corresponding with TV-14. The

language for TV-MA is blocked as well.)

Notes: Broadcasters are not required to provide content themes or

age-based ratings.

You must remember to lock Parental Controls for rating limits to

take effect.

Tip

To change all V-Chip movie or TV ratings to View, press

the 0 number button.

Chapter 3

Graphics contained within this publication are for representation only.

Download from Www.Somanuals.com. All Manuals Search And Download.

Using the TV’s Features

Viewing Speciﬁc Content Themes

If you block speciﬁc content themes, you have the option of going back and changing some of the them back to ( ) View:

1. Determine the content themes you want to change to ( ) View.

2. Press the down arrow button to scroll to the rating whose content theme you want to change, such as under

language (L) corresponding with TV-14.

3. Press the right arrow button to move the yellow highlight to a particular content theme status.

4. Press the OK button to change the status back to . Your child would then be able to watch programs with the TV-14

adult language content, but not programs with TV-MA language content.

Note: Only the content theme status corresponding to TV-14 (L) language changes to (V) View. Higher rated content

themes, such as that for TV-MA language, do not change.

Canada V-Chip Ratings

Canadian TV V-Chip supports two different Canadian rating systems: English and French.

Rating

18+

Canadian English V-Chip Rating System

Adults. Programming intended for adults 18 and older. It may contain elements of violence, language, and

sexual content which could make it unsuitable for viewers under 18. Violence Guidelines: May contain

violence integral to the development of the plot, character or theme, intended for adult audiences. Other

Content Guidelines: May contain graphic language and explicit portrayals of nudity and/or sex.

Viewers 14 and over. Programming contains themes or content which may not be suitable for viewers

under the age of 14. Parents are strongly cautioned to exercise discretion in permitting viewing by pre-

teens and early teens. Violence Guidelines: May contain intense scenes of violence. Could deal with mature

themes and societal issues in a realistic fashion. Other Content Guidelines: May contain scenes of nudity

and/or sexual activity. There could be frequent use of profanity.

14+

Parental Guidance. Programming intended for a general audience but which may not be suitable for

younger children (under the age of 8). Parents may consider some content inappropriate for unsupervised

viewing by children aged 8-13. Violence Guidelines: Depictions of conﬂict and/or aggression will be limited

and moderate; may include physical, fantasy, or supernatural violence. Other Content Guidelines: May

contain infrequent mild profanity, or mildly suggestive language. Could also contain brief scenes of nudity.

General Audience. Programming considered acceptable for all ages groups. While not designed

speciﬁcally for children, it is understood younger viewers may be part of the audience. Violence Guidelines:

Will contain very little violence, either physical or verbal or emotional. Will be sensitive to themes which

could frighten a younger child, will not depict realistic scenes of violence which minimize or gloss over the

effects of violent acts. Other Content Guidelines: There may be some inoffensive slang, no profanity and no

nudity.

Children 8 and older. Programming generally considered acceptable for children 8 years and over to

watch on their own. Violence Guidelines: Violence will not be portrayed as the preferred, acceptable,

or only way to resolve conﬂict or encourage children to imitate dangerous acts which they may see on

television. Any realistic depictions of violence will be infrequent, discreet, of low intensity and will show

the consequences of the acts. Other Content Guidelines: There will be no profanity, nudity or sexual

content.

C8+

Children. Programming intended for children under age 8. Violence Guidelines: Careful attention is paid to

themes which could threaten children’s sense of security and well being. There will be no realistic scenes

of violence. Depictions of aggressive behavior will be infrequent and limited to portrayals that are clearly

imaginary, comedic or unrealistic in nature. Other Content Guidelines: There will be no offensive language,

nudity or sexual content.

Chapter 3

Graphics contained within this publication are for representation only.

Download from Www.Somanuals.com. All Manuals Search And Download.

Using the TV’s Features

Rating

Canadian French V-Chip Rating System

Adults. Programming is for adults only. This program contains sustained violence or extremely violent

scenes.

18 ans +

Viewers 16 and over. Programming is not suitable for those under age 16. This program contains

frequent scenes of violence or intensely violent scenes.

16 ans +

13 ans +

Viewers 13 and over. Programming may not be suitable for children under the age of 13. This

program either contains several violent scenes or one or more scenes that are violent enough to affect

them. Viewing in the company of an adult is therefore strongly recommended for children under the

age of 13.

Viewers 8 and over. Not recommended for young children. This program is suitable for most

audiences, but it contains mild or occasional violence that could upset young children. Viewing in

the company of an adult is therefore recommended for young children (under the age of 8) who

do not distinguish between reality and imagination. Programming generally considered acceptable

for children 8 years and over to watch on their own. Violence Guidelines: Violence will not be

portrayed as the preferred, acceptable, or only way to resolve conﬂict or encourage children to

imitate dangerous acts which they may see on television. Any realistic depictions of violence will

be infrequent, discreet, of low intensity and will show the consequences of the acts. Other Content

Guidelines: There will be no profanity, nudity or sexual content.

8 ans +

General Audience. This program is suitable for audiences of all ages. It contains no violence, or any

violence that it does contain is either minimal or is presented in a humorous manner, as a caricature,

or in an unrealistic way.

Blocking Canadian V-Chip Ratings

If you receive Canadian programs you can block Canadian English and

French V-Chip by ratings only. When you block a particular rating, you

automatically block the higher rated programs as well.

To block Canadian English and French program ratings:

1. Select Canada V-Chip from the Parental Control menu.

2. Highlight English ratings or French ratings and press OK.

3. Determine the rating you want to block.

4. Press the down arrow button to scroll to the rating you want to

change.

5. Press the OK button to change its status to block (the lock icon

appears and all ratings above the one you selected change to lock).

Chapter 3

Graphics contained within this publication are for representation only.

Download from Www.Somanuals.com. All Manuals Search And Download.

Using the TV’s Features

V-Chip Movie Rating Limit

Set movie rating limits by blocking movies rated above a speciﬁed level.

To access the Movie Rating Limit menu:

1. Press MENU on the remote control (the TV's MAIN MENU appears).

2. Select Parental Control.

3. Select US V-Chip.

4. Select V-Chip movie rating.

Blocking Movie Ratings

Once you are in the Movie Ratings menu, follow the same steps

described for blocking TV ratings.

Blocking Unrated/Exempt Programs

The Unrated/Exempt Prog. option lets you decide if programs that the

V-Chip recognizes as unrated can be viewed. Unrated TV programs may

include news, sports, political, religious, local and weather programs,

emergency bulletins, public announcements, and programs without

ratings. The Exempt option applies to both USA and Canadian unrated

programs and Canadian programs rated E.

View All unrated programs are available.

Block All unrated programs are not available.

Note: You must remember to activate V-Chip for rating limits to

take effect.

Press the down arrow to highlight Unrated/Exempt Prog. Then press the

right arrow to toggle between View and Block.

Lock/Unlock Parental Controls

Selecting this option lets you lock and unlock parental controls settings using a password.

If you do not lock parental controls, none of the settings for V-Chip, Channel Block, or Front Panel Block will

take effect.

If you forget your password, press the MENU button, then select Parental Control (the password entry screen appears).

Simultaneously press and hold CH+ and VOL+ on the front panel for 8 seconds. Parental Controls unlock and the Parental

Control menu appears. You can enter a new password by locking the Parental Controls again.

Front Panel Block

Selecting this option lets you block (disable) or unblock (enable) the TV’s front panel. The remote still tunes to any channel.

When using this as a Parental Control method, remove access to any remote that is capable of operating the television while

you have the front panel blocked.

Don’t forget to lock parental controls after you change the status. If you don’t, the front panel block will not take effect.

Chapter 3

Graphics contained within this publication are for representation only.

Download from Www.Somanuals.com. All Manuals Search And Download.

Using the TV’s Features

PIP (Picture-in-Picture) and POP

(Picture-outside-Picture) Operation

The PIP (picture-in-picture) feature lets you display a second, smaller

picture on top of the main picture. POP (picture-outside-picture) lets you

display two windows side by side.

Note: PIP and POP are not available for DVI or component video

sources (CMP1 or CMP2).

PIP example

POP example

PIP and POP Buttons

There are several remote buttons that control the way the PIP window

works:

��

PIP Brings up the PIP window. Press again to bring up POP. Press again

to remove the window.

�

Up and down arrow buttons Let you move the PIP window to

different corners of the screen. Up arrow moves PIP counterclockwise;

down arrow moves PIP clockwise.

��

Left and right arrow buttons Switches the main POP window, where

the sound is coming from, with the other window.

��

�

PIP + and PIP - Lets you change channels in the PIP and right POP

window.

�

��

�

��

Chapter 3

Graphics contained within this publication are for representation only.

Download from Www.Somanuals.com. All Manuals Search And Download.

Using the TV’s Menu System

Sound Menu

The Sound menu lets you adjust audio output. To access the Sound menu,

press MENU on the remote, and then select Sound from the main menu. The

following audio items can be adjusted: Sound settings, Sound type, Sound mode,

SAP, Sound Logic, Dynamic bass, Headphone settings, and Graphic equalizer.

Sound settings The Sound settings submenu contains the following items:

Left & Right balance Use the left or right arrow to center the bar under the

arrow to balance the left and right speakers.

Ampliﬁer Use the left or right arrow button to select External (if your TV is

using external ampliﬁer only) or Internal (if your TV is using the speakers

in the TV).

Subwoofer Select External if the TV is using an external subwoofer, or None

if the TV is not using a subwoofer.

Sound type Press the right arrow button to scroll through the available audio

types, which control the way the sound comes through your speakers. The

options available vary according to the input selected.

Mono (available for regular TV viewing only) Plays the sound in mono

only. Use this setting when receiving broadcasts with weak stereo signals.

Stereo Splits the incoming stereo audio signal into left and right channels.

Most TV programs and recorded materials have stereo audio. The word

Stereo appears in the channel banner when you tune to a program that is

broadcast in stereo.

Automatic (available for regular TV viewing only) Chooses the sound type

according to the current signal.

Left and Right (available for audio/video inputs only) Isolates either the

left or right channel of the incoming audio.

Sound Mode Press the right arrow button to scroll through the available audio

modes, which provides special processing through your speakers (depending on

the setting you chose as your Sound type).

Normal Does not give any special processing, simply provides the mono

or stereo sound provided by the signal you're watching.

Wide Available only for mono signals. “Widens” sound from mono

broadcasts and mono components connected to your TV for a fuller, more

spacious sound.

Magic Available only for stereo signals. Gives a surround effect with more

bass.

Second Audio Program (SAP) Plays the program’s audio in a second

language, if one is available. The letters "SAP" appear in the channel banner

when you tune to a program that is broadcast with SAP information. SAP audio

is broadcast in mono. SAP is also used to broadcast a program’s audio with

descriptions of the video for the visually impaired.

Continues on next page...

Chapter 4

Graphics contained within this publication are for representation only.

Download from Www.Somanuals.com. All Manuals Search And Download.

Using the TV’s Menu System

Sound logic Reduces the annoying blasts in volume during commercial

breaks, and also ampliﬁes softer sounds in program material. Eliminates the

need to constantly adjust the volume.

Dynamic bass Enhances your TV's low-frequency response. The options are

Off, Medium and High.

Headphone settings Displays a choice list of available settings you can

adjust: Volume, Bass and Treble. The Headphone sound option allows you to

choose stereo, mono or automatic. These descriptions are same as for Sound

Type (see the previous page).

Graphic equalizer Allows you to choose a speciﬁc preset through the Sound

Preset option. Press the right arrow to cycle through the options: Standard,

Movie, Voice, Music, Flat, Videogame, Video camera and Personal.

The Frequency range displays the different treble and bass bands set for each

Sound Preset option. You can choose a band and make adjustments. When you

make adjustments, the Sound Preset option automatically changes to Personal.

Press the left or right arrow button to select the frequency (Bass 100Hz, Mid

Bass 500Hz, Medium 1.5kHz, Mid Treble 5kHz, Treble 10kHz) you want to

adjust. Then use the up or down arrow button to adjust the level.

To view the frequency range of another Sound Preset option, press the right or

left arrow until no band is selected and Frequency range is highlighted. Then

press the up arrow to highlight Sound Preset.

Picture Menu

The Picture menu contains menus and controls to conﬁgure the following video

settings: Advanced picture settings, Picture presets, Black level, Color, Contrast,

Sharpness, Color Warmth, and Tint. The Picture menu options apply to the

video for the main TV and video input selections.

Advanced picture settings

Contrast expand You can adjust the contrast of the picture to suit the light

of the room. Press the right arrow to choose which of the following best

describes the lighting in the room: Low, Medium or High.

Scan Velocity Modulation Improves the sharpness of the picture by

changing the speed of the cathode-ray tube’s electron beam when it

transitions between dark and light areas of the screen. Choose to have it on

(box checked) or off (box unchecked), depending on your preference.

Autoformat When enabled (box checked) the TV automatically detects

the screen format the signal is sending for each channel, as well as input

channels.

Tip:

If the picture is switching screen formats

abruptly during normal TV viewing, switch the

Autoformat feature off.

Chapter 4

Graphics contained within this publication are for representation only.

Download from Www.Somanuals.com. All Manuals Search And Download.

Using the TV’s Menu System

Video noise reduction Reduce picture “static” or any type of interference.

This feature is especially useful for providing a clearer picture in weak

analog signal conditions. Press the right arrow to choose between: Off for

no noise reduction; Minimum for a softer, smoother picture that retains

picture sharpness and detail; Medium for a slightly softer picture than the

Minimum setting; Maximum for an even softer, smoother picture than the

other settings (the picture detail is somewhat decreased).

Optimized still picture When enabled (box checked), enhances the picture

speciﬁcally for still frames (for example, if you're watching a slideshow on

your HDTV monitor, or if you've paused a frame of a DVD).

Auto Skin Tone When enabled (box checked), minimizes the ﬂesh tone

variations of the TV picture.

Film mode (3:2 Pulldown) Automatically detects video sources that were

originally recorded on ﬁlm (like most movies) and subsequently converted

to a different format (for TV broadcast, for example). Film mode processes

the converted signal so that it looks as close as possible to the original.

Another name for this process is reverse 3:2 pulldown.

Advanced (recommended) enables the feature only when the TV

detects that movie playback quality could be improved. Advanced is

the default setting.

The On setting should only be used in rare circumstances when the TV

is used solely with ﬁlm-based sources (like DVDs on a non-progressive-

scan player).

The Off setting turns off ﬁlm mode upconversion. Try using this

setting if you think the reverse 3:2 pulldown is causing distortions in

your picture.

Note: Autoformat and Video noise reduction are available for CMP1 and

CMP2 inputs only if the signal is 480i.

Picture Presets Displays a choice list that lets you select one of the preset

picture settings: Vibrant, Cinematic, Natural, Sports, Videogame, Video Camera

or Personal. Choose the setting that is best for your viewing environment. You

can set a different picture preset for each input (including one for your regular

TV channels).

Tip:

You can select a different picture preset

(or set up a different personal preset)

for each input. The ANTENNA/CABLE

jack counts as a single input.

Black Level Adjusts the brightness of the picture.

Color Adjusts the richness of the color.

Contrast Adjusts the difference between the light and dark areas of the

picture.

Sharpness Adjusts the crispness of the edges in the picture.

Note: You can adjust sharpness for each channel and input. This is useful if

the signal appears fuzzy.

Color Warmth Displays a choice list that lets you set one of three automatic

color adjustments: Cool for a more blue palette of picture colors; Normal; or

Warm for a more red palette of picture colors. The warm setting corresponds to

the NTSC standard of 6500 K.

Tint Adjusts the balance between the red and green levels.

When you change any of these picture settings, the Picture Preset changes to

Personal. Use the left or right arrow button to make adjustments. To return to

the Picture menu, press the up or down arrow button.

Chapter 4

Graphics contained within this publication are for representation only.

Download from Www.Somanuals.com. All Manuals Search And Download.

Using the TV’s Menu System

Channel Guide Menu

Allows you to view and select from the entire channel list and their labels. Press

the GUIDE button to bring up the Channel Guide menu. Use the up or down

arrow to scroll through the list. Press OK to select and tune to the highlighted

channel. Press the last digit of one of the channels in the guide to tune to that

channel and leave the Channel Guide on the screen.

Time Menu

Sleep Timer Lets you set the TV to turn off after a given amount of time.

Time Lets you enter the current time. If it is eight o’clock, for example, you

must ﬁrst enter the number zero, then number eight. Use the OK button to

choose between AM and PM.

Wake up timer Lets you set the TV to turn itself on. When you turn on Wake

up timer, the following options appear:

Wake up time Lets you set the time you want the TV to turn itself on.

Wake up duration Lets you set how long you want the TV to stay on when

it turns on.

Channel number Lets you select a speciﬁc channel the TV tunes to when

the wake up timer is set.

Daily Lets you choose if you want the wake up timer to turn on daily.

Note: The Wake up timer is available only when the time has been set.

Parental Control Menu

The Parental Control Menu was explained in Chapter 3. Go to page 26 for more

information.

Chapter 4

Graphics contained within this publication are for representation only.

Download from Www.Somanuals.com. All Manuals Search And Download.

Using the TV’s Menu System

PIP Menu

Display Mode

Off No window is displayed.

PIP PIP window is displayed.

POP POP window is displayed.

PIP channel Allows you to choose the channel displayed in the PIP or main

POP window. Scroll through channel list as well as the VID1, VID2 and FRNT

input channels.

PIP size Allows you to choose the size of the PIP window: Small, Medium or

Large.

PIP position Allows you to choose where the PIP window appears on the

screen: Top right, Top left, Bottom right or Bottom left.

Note: Pip size and position are not available for POP.

Setup Menu

The Setup menu lets you conﬁgure the TV to ﬁt its surroundings and your

preferences. To access the Setup menu, press MENU on the remote, and then

select Setup from the main menu.

Channel setup

Signal Type The TV chooses the signal type during the initial setup. If you

change how you receive broadcasts through the antenna input, you must

change the Signal type setting. Choose Cable if you are using cable or a

cable box for TV signals. Choose UHF/VHF Antenna if you are using an off-

air antenna for TV signals.

Auto channel search Searches for channels the signal is receiving. Go to

page 16 for more information.

Auto channel update Searches for any new channels that are not in your

channel list and adds them to the list.

List and labels Edit the channels in the list or choose labels for each

channel. Go to page 17 for more information.

Preferences

Language Displays a choice list that lets you select your preferred

language for the menus: English, Español or Français.

Maximum TV volume Allows you to set how high volume turns up when

you press the VOL+ button. Highlight Maximum volume, then press and

hold OK to hear the maximum volume. Make sure the volume has not been

muted or turned down all the way.

Continues on next page...

Chapter 4

Graphics contained within this publication are for representation only.

Download from Www.Somanuals.com. All Manuals Search And Download.

Using the TV’s Menu System

Curtain effect Reveals the picture by "opening" it from the middle of the

screen when the TV is switched on. Hides the picture by "closing" it from the

sides when the TV is switched off.

Short-term vs. Long-term

Power Outages

The Auto channel and Auto volume settings

don’t take effect after short-term power

outages (usually less than two to three

minutes). The TV will turn back on at the

same volume and channel as before the

power outage.

Special features The Auto on setting switches your TV on after a power

outage; Auto channel tunes the TV to the channel you specify as the Initial

channel when Auto on is enabled; Auto volume tunes the TV to the volume

you set in Initial volume when Auto on is enabled.

The Auto channel and Auto volume settings

take effect after power outages of several

minutes or more.

Closed Caption Many programs are encoded with closed-captioning

information, which lets you display the audio portion of a program as text on the

TV screen.

Closed captioning is not available on all channels at all times. Only speciﬁc

programs encoded with closed-captioning information. When a program is

closed captioned, CC is displayed in the channel banner. See Chapter 3 for more

information about the channel banner. The closed caption options are:

Closed caption setting Lets you choose the way closed captioning

information appears on the screen. The Closed caption setting does not effect

the DVI-HDTV input.

Off No captioning information displayed.

On always Captioning information shown always, when available.

On when mute Displays captioning information, when available,

whenever the TV’s sound is muted by pressing the MUTE button. The

captioning information is not displayed when the sound is not muted.

Closed-Caption Mode Displays a choice list that lets you choose which

captioning mode is used for displaying captioning information. If you are

unsure of the differences among the modes, you may prefer to leave the

closed captioned mode set to CC1, which displays complete text of the

program in the primary language in your area.

Autotuning Displays a choice list that lets you set up the TV to automatically

tune to the correct input channel when you press a component button (DVD

or AUX/HD) on the remote. Go to Chapter 3 for details about the Autotuning

feature.

Convergence The Auto convergence feature automatically adjusts the TV’s

tubes (this may take several minutes, after which you can make ﬁne adjustments

to the convergence settings); Red convergence displays the Red convergence

screen, allowing you to use the arrow buttons to align the red and green images;

Blue convergence displays the Blue convergence screen, allowing you to use the

arrow buttons to align the blue and green images.

Chapter 4

Graphics contained within this publication are for representation only.

Download from Www.Somanuals.com. All Manuals Search And Download.

Other Information

Troubleshooting

Most problems you encounter with your TV can be corrected by consulting the following troubleshooting list.

Note for US customers: If you prefer, we can provide you with the name of an Authorized Service Representative who

will visit your home for a fee to install your electronic entertainment system and to instruct you in its operation. For

details about this service, call 1-888-206-3359.

For additional assistance while using your RCA product, please visit www.rca.com/customersupport.

TV Problems

TV won’t turn on

•

Press the TV button.

Make sure the TV is plugged in.

Check the wall receptacle (or extension cord) to make sure it is “live” by plugging in something else.

Something might be wrong with your remote control. Press the POWER button on the front of the TV. If the TV turns on, check the

remote control solutions on the next page.

•

The front panel controls may be locked (disabled). Use the remote control to unlock the front panel controls by selecting the Front

Panel Block in the Parental Control menu and press OK to uncheck the box.

The TV might be performing a periodic diagnostic check. Wait for a few minutes for the TV to turn on.

Buttons don’t work

•

If you’re using the remote control, press the TV button ﬁrst to make sure the remote is in TV mode.

•

The front panel controls may be locked (disabled). Use the remote control to unlock the front panel controls by selecting the Front

Panel Block in the Parental Control menu and press OK to uncheck the box.

•

Unplug the TV for ten minutes and then plug it back in. Turn the TV on and try again.

TV turns off unexpectedly

•

Sleep timer may have been activated. Go to page 36 for instructions.

•

Electronic protection circuit may have been activated because of a power surge. Wait 30 seconds and then turn on again. If this

happens frequently, the voltage in your house may be abnormally high or low.

•

Unplug. Wait ten minutes. Plug in again.

TV turns on unexpectedly

•

Wake up timer might have been activated. Go to page 36 for instructions.

Auto on might have been activated. Go to page 38 for instructions.

You might have pressed CH+, CH- or INPUT on the remote accidentally.

Blank screen

•

Make sure the component connected to the TV is turned on.

Try another channel.

If you're trying to watch something that's playing on a component connected to the TV (like a DVD or a VCR tape), press the TV

button on the remote, then press INPUT until you get to the correct video input channel.

No sound, picture okay

•

Maybe the sound is muted. Try pressing the volume up button to restore sound.

•

If using S-Video or Y, PB, PR, remember to also connect the component’s left and right audio output jacks to the TV’s L and R Audio

Input jacks.

•

If you're using the TV's internal speakers, make sure the INT/EXT switch on the back of the TV is put on “INT”.

The sound settings may not be set correctly. Go to page 33 for more information.

Can’t select certain channel

•

Make sure the remote control is in TV mode. Press the TV button and enter the channel number using the number buttons.

Channel may be blocked or not approved in the Parental Controls menu.

If using a VCR, check to make sure the TV/VCR button on the VCR is in the correct mode (press the TV/VCR button on your VCR).

Continues on next page...

Chapter 5

Graphics contained within this publication are for representation only.

Download from Www.Somanuals.com. All Manuals Search And Download.

Other Information

Noisy stereo reception

•

May be a weak station. Use Sound menu to choose mono sound.

No picture, no sound but TV is on

•

Maybe the cable/air function is set to the wrong position. Go to page 37 for detailed instructions.

The channel might be blank — change channels.

If you’re watching your VCR and it’s connected with coaxial cable to the CABLE/ANTENNA jack, tune the TV to channel 3 or 4

(whichever channel is selected on the 3/4 switch on the back of your VCR). Also check to make sure the TV/VCR button on the VCR

is in the correct mode (press the TV/VCR button on your VCR).

Sound okay, picture poor

•

Check antenna connections. Make sure all of the cables are ﬁrmly connected to the jacks.

•

Try adjusting sharpness function to improve weak signals. Go to page 35 for more instructions.

Volume buttons not adjusting volume louder

•

Check to make sure volume isn’t limited by the maximum volume feature. Go to page 37 for more instructions.

Picture not moving

•

You have activated the Freeze feature by pressing FREEZE or OK on the remote. Press any button to “unfreeze” the picture.

Black box appears on the screen

•

Closed-captioning might be on. Check Closed Caption in the Setup menu. Go to page 38 for more instructions.

Freeze not working

•

The freeze feature is not available for Component video (CMP1 or CMP2) or DVI inputs.

Low battery warning appears on screen

•

Place new batteries in remote.

TV picture keeps switching between screen formats abruptly

•

Switch the Auto format feature to Off. See page 34 for more information.

The Remote Control Doesn’t Work

•

Something might be between the remote and the remote sensor on the component. Make sure there is a clear path.

Maybe the remote isn’t aimed directly at the component (TV, VCR, DVD player, etc.) that you’re trying to operate.

Maybe remote is not in TV Mode. Press the TV button so remote will control TV.

Maybe batteries in remote are weak, dead, or installed incorrectly. Put new batteries in the remote. (Note, if you remove the

batteries, you may have to reprogram the remote to operate other components.)

•

You might need to drain the remote’s microprocessor: remove batteries and press the number 1 button for at least 60 seconds.

Release the 1 button, replace the batteries, and (if necessary) program the remote again.

Make sure there’s nothing plugged into the WIRED IR jack on the TV’s back panel. The remote that came with your TV won’t work if

anything is plugged into this jack.

Problems with V-Chip/Parental Controls

The rating limits don’t work

•

You must lock the settings. Go to the MAIN MENU (press MENU on your remote), select Parental Control, select Lock Parental

Controls.

I don’t remember my password and I want to unlock the TV

•

If you forget your password, press MENU, then select Parental Control (the password entry screen appears). Simultaneously press

and hold CH+ and VOL+ on the TV’s front panel for 8 seconds. The Parental control menu appears on the screen, and you can re-

enter a password via Lock Parental Controls.

The V-Chip won’t let me watch a program even though it’s not rated as violent.

•

Maybe the movie was given an NR (Not Rated) status. After you block movie ratings, you must set NR to View separately in order to

view movies with an NR rating.

Chapter 5

Graphics contained within this publication are for representation only.

Download from Www.Somanuals.com. All Manuals Search And Download.

Other Information

FCC Information

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of

the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential

installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in

accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee

that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or

television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct

the interference by one or more of the following measures:

•

Reorient or relocate the receiving antenna.

Increase the separation between the equipment and receiver.

Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.

Consult the dealer or an experienced radio/TV technician for help.

This Class B digital apparatus complies with Canadian ICES-003.

Care and Cleaning

CAUTION: Turn OFF your TV before cleaning.

You can clean the TV as required, using a soft lint-free cloth. Be sure to occasionally dust the ventilation slots in the cabinet

to help assure adequate ventilation.

The TV’s screen may be cleaned with a soft, lint-free cloth as well. Take care not to scratch or mar the screen. If

necessary, you may use a cloth dampened with warm water. Never use strong cleaning agents, such as ammonia-

based cleaners, or abrasive powder. These types of cleaners will damage the TV.

While cleaning do not spray liquid directly on the screen, or allow liquid to run down the screen and inside the TV. Also,

never place drinks or vases with water on top of the TV. This could increase the risk of ﬁre or shock hazard or damage to

the TV.

Caution: Using video games or any external accessory with ﬁxed images for extended periods of time can cause them to

be permanently imprinted on the picture tube (or projection TV picture tubes). ALSO, some network/program logos, phone

numbers, etc. may cause similar damage. This damage is not covered by your warranty.

Chapter 5

Graphics contained within this publication are for representation only.

Download from Www.Somanuals.com. All Manuals Search And Download.

Other Information

RCA HDTV Monitor Limited Warranty

What your warranty covers:

•

Defects in materials or workmanship.

For how long after your purchase:

•

One year from date of purchase for labor.

One year from date of purchase for parts.

Two years from date of purchase for the picture tube.

The warranty period for rental units begins with the ﬁrst rental or 45 days from date of shipment

to the rental ﬁrm, whichever comes ﬁrst.

What we will do:

•

Pay an Authorized Service Center the labor charges to repair your unit.

•

Pay an Authorized Service Center for the new, or at our option, refurbished replacement parts

and picture tube required to repair your unit.

How you get service:

•

Call 1-877-RCA-HDTV and have your unit’s date of purchase and model number ready.

A representative will troubleshoot your problem over the phone.

If the representative determines that you should receive service, they will provide you with

the name(s) of the Authorized Service Center in your area.

•

Contact the Service Center and arrange for home or pick up, repair, and return service,

provided that your unit is located within the geographic territory covered by an Authorized

Service Center. If not, you must take your unit to the Service Center location at your own

expense, or pay for the cost the Service Center may charge to transport your unit to and from

your home.

Proof of purchase in the form of a bill of sale or receipted invoice which is evidence that the

product is within the warranty period must be presented to obtain warranty service. For rental

ﬁrms, proof of ﬁrst rental is also required.

What your warranty does not cover:

•

Customer instruction. (Your Owner’s Manual describes how to install, adjust, and operate

your unit. Any additional information should be obtained from your dealer.)

•

Installation and related adjustments.

Signal reception problems not caused by your unit.

Damage from misuse or neglect.

Batteries.

Images burnt onto the screen.

A unit that has been modiﬁed or incorporated into other products.

A unit purchased or serviced outside the U.S.A.

Acts of nature, such as but not limited to lightning damage.

Product Registration:

•

Please complete the online Product Registration on RCA.com or complete and mail the

Product Registration Card packed with your unit. It will make it easier to contact you should

it ever be necessary. The return of the card is not required for warranty coverage.

Chapter 5

Graphics contained within this publication are for representation only.

Download from Www.Somanuals.com. All Manuals Search And Download.

Other Information

Limitation of Warranty:

•

THE WARRANTY STATED ABOVE IS THE ONLY WARRANTY APPLICABLE TO THIS

PRODUCT. ALL OTHER WARRANTIES, EXPRESS OR IMPLIED (INCLUDING ALL IMPLIED

WARRANTIES OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE) ARE

HEREBY DISCLAIMED. NO VERBAL OR WRITTEN INFORMATION GIVEN BY THOMSON

INC., ITS AGENTS OR EMPLOYEES SHALL CREATE A GUARANTY OR IN ANY WAY

INCREASE THE SCOPE OF THIS WARRANTY.

•

REPAIR OR REPLACEMENT AS PROVIDED UNDER THIS WARRANTY IS THE EXCLUSIVE

REMEDY OF THE CONSUMER. THOMSON INC. SHALL NOT BE LIABLE FOR INCIDENTAL

OR CONSEQUENTIAL DAMAGES RESULTING FROM THE USE OF THIS PRODUCT

OR ARISING OUT OF ANY BREACH OF ANY EXPRESS OR IMPLIED WARRANTY ON

THIS PRODUCT. THIS DISCLAIMER OF WARRANTIES AND LIMITED WARRANTY ARE

GOVERNED BY THE LAWS OF THE STATE OF INDIANA. EXCEPT TO THE EXTENT

PROHIBITED BY APPLICABLE LAW, ANY IMPLIED WARRANTY OF MERCHANTABILITY

OR FITNESS FOR A PARTICULAR PURPOSE ON THIS PRODUCT IS LIMITED TO THE

APPLICABLE WARRANTY PERIOD SET FORTH ABOVE.

How State Law relates to warranty:

•

Some states do not allow the exclusion nor limitation of incidental or consequential damages,

or limitations on how long an implied warranty lasts, so the above limitations or exclusions

may not apply to you.

•

This warranty gives you speciﬁc legal rights, and you also may have other rights that vary

from state to state.

If you purchased your unit outside the United States:

•

This warranty does not apply. Contact your dealer for warranty information.

Service calls which do not involve defective materials or workmanship are not covered by

this warranty. Costs of such service calls are the sole responsibility of the purchaser.

Chapter 5

Graphics contained within this publication are for representation only.

Download from Www.Somanuals.com. All Manuals Search And Download.

Other Information

Accessory Information

There are various accessories available to complement your HDTV Monitor. Prices are subject to change without notice. All

accessories are subject to availability.

A shipping and handling fee will be charged upon ordering, and we are required by law to collect the appropriate sales tax

for each individual state, county and locality to which the merchandise is being sent.

HOW TO ORDER

To place an order by phone, have your Visa, MasterCard or Discover Card ready and call the toll-free number listed below.

Use this number only to place an order for accessory items.

1-800-338-0376

You can buy some accessories on-line at:

www.rca.com.

Screw-on Cable attaches to the round

antenna connectors (called 75-ohm

F-type) on the back of your VCR or TV.

The ends screw onto the connectors

for a secure connection.

S-Video Cable has multi-

pin connectors on each

end for connecting S-Video

components to your TV.

VH976 (6-ft.),

price: $7.95

VH913 (12-ft.),

price: $14.95

VH81 (3-ft), price: $3.95

VH82 (6-ft), price: $4.95

2-way Signal Splitter helps

you connect to a second TV

or VCR.

Push-on antenna cable attaches to

the round antenna connectors (called

75-ohm F-type). The ends push on for

a quick connection

VH47, price: $3.95

Ampliﬁed VHF/UHF/FM

Antenna allows you to easily

switch from the antenna signal

to cable or satellite easily

VH89 (6-ft.), price: $5.95

without disconnecting antenna.

Surge Protector provides eight

outlets, coaxial and telephone line

protection. Audible alarm for surge

failure. $100,000 Surge Equipment

Guarantee.

r e s e t

o f f

ANT200, price: $49.95

SCTV4000C,

price: $49.95

Remote Control This is

the remote control that

came packed with your TV.

Replacements or spares can be

ordered as needed.

Component Video Cables Triple

cable used to connect a video source

with Y, PR_,PBjacks to the TV.

261669, price: $28.25

Standard Audio/Video cable

with RCA-type phono plugs.

Gold-Tipped cable

VH83 (6-ft., mono), price: $5.95

VH84 (6-ft., stereo), price: $9.95

DT6DC (6-ft), price: $24.95

DT12DC (12-ft), price: $34.95

Chapter 5

Graphics contained within this publication are for representation only.

Download from Www.Somanuals.com. All Manuals Search And Download.

Index

Second audio program (SAP)

24, 33

Setup menu 16, 37, 38

Sharpness 35

Signal type 37

SKIP button 19, 24

Sleep timer 19, 36

Sound

Maximum TV volume 37

A/V receiver 12

Accessories 44

Direct entry 20, 21

DVD

Button 18, 25

Connection 6, 7, 10, 11

DVI input 13, 25

Dynamic bass 34

Button 16, 19

Channel guide 36

Language 16, 37

Parental control 36

Picture 34, 35

PIP 37

Setup 16, 37, 38

Sound 33, 34

Time 36

Age-based ratings 28

Ampliﬁer 33

ANTENNA/CABLE 14, 35

Arrow buttons 18, 32

Audio/Video cables 44

Audio jacks

Menu 33, 34

Mode 33

Front 14

Settings 19, 33

Type 33

Sound logic 34

Stereo 24, 33, 40

Subwoofer 14, 33

SWAP button 19, 32

Exempt programs 31

External speakers 12, 14

Outputs (ﬁxed/variable) 14

Autoformat 34, 40

Automatic code search 20

Autotuning 24, 25, 38

Auto channel search 16, 37

Auto channel update 37

Auto convergence 17, 38

Auto on 38

Mute 19, 24

FCC information 41

Film mode 35

Freeze 18, 40

FRNT input 25

Front panel

Block 31

Buttons 15

Jacks 14

ON•OFF button 19

Optimized still picture 35

Time 24, 36

Tint 35

Transport buttons 19

Troubleshooting 39, 40

TV button 16, 19

TV problems 39

Auto skin tone 35

AUX/HD button 18, 25

Parental control

Menu 36

Problems 40

Parental controls 2, 24, 26

Lock/unlock 31

Password 40

Picture menu 34

Picture presets 19, 35

PIP (Picture-in-picture) 2, 32

Button 19, 32

Channel 37

Menu 37

POP (Picture-outside-picture) 2,

19, 32, 37

Preferences 37, 38

Balance 33

Black level 35

Graphic equalizer 34

GUIDE button 18, 36

Cables

Audio/Video 5, 44

Coaxial 5, 44

Component video 5, 44

DVI 5

Unrated programs 31

US V-Chip ratings 26, 27, 31

HDTV Tuner 6, 7

Headphones

Jack 14

V-Chip 2, 26, 27

Canadian ratings 30

Movie rating limit 31

Problems 40

US ratings 31

VCR

Settings 34

S-Video 5, 44

Canadian V-Chip ratings 26, 30

English system 29

French system 30

Care and cleaning 41

Channel banner 24

Channel Guide menu 36

Channel number 24

Channel setup 37

CLEAR button 18

Closed captions 24, 38

CMP1/CMP2 inputs 13, 25

Coaxial cable 5, 44

Codes for the remote 23

Color 35

Initial setup 15, 16

Inputs

ANTENNA/CABLE 14, 35

Button 19, 22

CMP1 and CMP2 13, 25

DVI 13, 25

Button 19, 25

Rating limits

Problems 40

Connection 6, 7, 8, 9, 10, 11

Video input jacks

Front 14

VID1/VID2 13, 25

Video noise reduction 35

Volume punchthrough 22

Remote control

Backlight 19

Batteries 15, 40

Buttons 18, 19

Codes 23

FRNT 14, 25

VID1 and VID2 13, 25

Problems 40

Programming 20

Replacement 44

Use 15, 21

Jacks 13, 14

ANTENNA/CABLE 14, 25, 35

Audio 13, 14

Component video 13, 25

DVI 2, 13, 25

Front 14, 25

Wake up timer 36

Warranty 42

Color warmth 35

Commercial skip 19, 24

Component buttons 19, 21,

24, 38

Reverse 3:2 pulldown 2, 35

ZOOM button 19, 32

Connections 5

S-Video 13, 14, 25

Video 13, 14, 25

S-Video

Back input jacks 13, 25

Cable 44

Front input jack 14

Safety information 4

SAT/CAB button 19, 25

Satellite receiver 8, 9

Scan velocity modulation 34

Screen format 24, 34, 40

DVD 6, 7, 10, 11

HDTV Tuner 6, 7

Satellite receiver 8, 9

Things to consider before 4

VCR 6, 7, 8, 9, 10, 11

Content themes 28, 29

Contrast 35

Language 16, 37

Lists and labels 17, 37

Contrast expand 34

Convergence 38

Curtain effect 38

Chapter 5

Download from Www.Somanuals.com. All Manuals Search And Download.

Visit the RCA website at www.rca.com

Please do not send any products to the Indianapolis address listed in this manual or on the carton. This will only

add delays in service for your product.

Thomson Inc.

10330 North Meridian Street

Indianapolis, IN 46290

Trademark(s)® Registered

Marca(s) Registrada(s)

Printed in USA

TOCOM 1620611B

Download from Www.Somanuals.com. All Manuals Search And Download.

Radio Shack Headphones 33 1113 User Guide
Radio Shack Pager 17 8002 05 User Guide
Radio Shack Radar Detector XKKa User Guide
Renesas Computer Hardware H8SX 1648 User Guide
RIDGID Camping Equipment AM2500 User Guide
Salton Coffee Grinder SG8SS User Guide
Samsung Flat Panel Television 203B User Guide
Samsung MP3 Player SPF 85P User Guide
Sanus Systems TV Mount VMSA User Guide
Schwinn Home Gym 113 213 User Guide