v5.0 (EN/E)
equipment off and on, the user is
encouraged to try to correct the
interference by one or more of
the following measures:
PLEASE READ AND SAVE THIS FOR FUTURE REFERENCE
This Class B digital apparatus
complies with Canadian ICES-003.
Cet appareil numérique de la
classe B est conforme à la norme
NMB-003 du Canada.
FCC information
This equipment has been tested
and found to comply with the
limits for a Class B digital device,
pursuant to Part 15 of FCC Rules.
These limits are designed to
provide reasonable protection
against harmful interference in
a residential installation. This
equipment generates, uses, and
can radiate radio frequency
energy and, if not installed
and used in accordance with
the instructions, may cause
harmful interference to radio
communications.
IMPORTANT SAFETY INSTRUCTIONS
user manual
manual de usuario
Some of the following
the provided plug does not
fit into your outlet, consult an
electrician for replacement of
the obsolete outlet.
Protect the power cord
from being walked on or
pinched particularly at plugs,
convenience receptacles, and
the point where they exit from
the apparatus.
plug is damaged, liquid has
been spilled or objects have
fallen into the apparatus, the
apparatus has been exposed
to rain or moisture, does not
operate normally, or has been
dropped.
information may not apply to
your particular product; however,
as with any electronic product,
precautions should be observed
during handling and use.
•
•
Reorient or relocate the
receiving antenna.
Increase the separation
between the equipment and
receiver.
Manufacturer/Responsible
Party
Audiovox Electronics Corp.,
150 Marcus Blvd., Hauppauge, NY
11788
•
RP5415
RP5415PK
•
•
•
•
•
Read these instructions.
Keep these instructions.
Heed all warnings.
•
•
Connect the equipment into
an outlet on a circuit different
from that to which the
receiver is connected.
Consult the dealer or
an experienced radio/TV
technician for help.
ADDITIONAL SAFETY
INFORMATION
Follow all instructions.
Do not use this apparatus near
water.
•
•
Only use attachments/
accessories specified by the
manufacturer.
•
Main plug is used as
disconnect device and it
•
•
Clean only with dry cloth.
Do not block any ventilation
openings. Install in accordance
with the manufacturer’s
instructions.
Do not install near any heat
sources such as radiators, heat
registers, stoves, or other
apparatus (including amplifiers)
that produce heat.
Do not defeat the safety
purpose of the polarized
or grounding-type plug. A
polarized plug has two blades
with one wider than the
other. A grounding type plug
has two blades and a third
grounding prong. The wide
blade or the third prong is
provided for your safety. If
should remain readily operable
during intended use. In order
to disconnect the apparatus
from the mains completely,
the mains plug should be
disconnected form the mains
socket outlet completely.
Apparatus shall not be exposed
to dripping or splashing and
no objects filled with liquids,
such as vases, shall be placed
on the apparatus.
Use only with the
cart, stand, tripod,
However, there is no guarantee
that interference will not occur
in a particular installation. If
this equipment does cause
harmful interference to radio or
television reception, which can
be determined by turning the
]
Modifications not expressly
approved by the party responsible
for compliance could void the
user’s authority to operate the
equipment.
bracket, or table
specified by the
manufacturer,
•
•
or sold with the apparatus.
When a cart is used, use
caution when moving the cart/
apparatus combination to
avoid injury from tip-over.
Unplug this apparatus during
lightning storms or when
unused for long periods of
time.
Refer all servicing to qualified
service personnel. Servicing is
required when the apparatus
has been damaged in any way,
such as power-supply cord or
•
•
WARNING:
TO PREVENT FIRE
OR ELECTRICAL
SHOCK HAZARD,
DO NOT EXPOSE
THIS PRODUCT TO
RAIN OR MOISTURE.
•
•
Always leave sufficient space
around the product for
ventilation. Do not place
product in or on a bed, rug,
in a bookcase or cabinet that
may prevent air flow through
vent openings.
EN/E
It is important to read this user manual prior to using your new product for the first time.
Es importante leer este manual antes de usar por vez primera su equipo.
SEE MARKING ON BOTTOM OF PRODUCT
•
•
•
•
Do not place lighted candles,
cigarettes, cigars, etc. on the
product.
Connect power cord only to
AC power source as marked on
the product.
Care should be taken so that
objects do not fall into the
product.
Do not attempt to disassemble
the cabinet. This product
does not contain customer
serviceable components.
The marking information
is located at the bottom of
apparatus.
Important Battery Precautions
The descriptions and
For your records
•
•
•
Any battery may present a risk
of fire, explosion, or chemical
burn if abused. Do not try to
charge a battery that is not
intended to be recharged, do
not incinerate, and do not
puncture.
Non-rechargeable batteries,
such as alkaline batteries, may
leak if left in your product for
a long period of time. Remove
the batteries from the product
if you are not going to use it
for a month or more.
If your product usaes more
than one battery, do not mix
types and make sure they are
inserted correctly. Mixing types
or inserting incorrectly may
cause them to leak.
characteristics in this owner’s
manual are for the purpose of
general reference only and not as
a guarantee. In order to provide
you with the highest quality
product, we may make changes
or modifications without prior
notice.
Before you begin
In the event that service should
be required, you may need the
model number and the serial
number. In the space below,
record the date and place of
purchase and the serial number:
Model No.:
Battery back-up operation
The power failure protection
circuit will not operate unless
battery is installed.
Plugging in for power
AC OUTLET POWER SUPPLY:
120V~60Hz
Power failure indicator
When AC power is interrupted
(disconnected) for a short period
of time, both time and alarm
settings will change (unless
battery is installed). After AC
power is restored (reconnected),
the Digital Display will blink
to indicate that power was
interrupted and you should
readjust the time and alarm
settings.
Alkaline (NEDA 1604A/
IEC 6LR61) battery is
recommended. Carbon-
zinc battery may be used but
memory holding time will
be substantially reduced.
Memory holding time for
a fresh alkaline battery is
approximately 8 hours (if radio
or alarm are not operated)
which should take care of
short, nuisance-type AC power
failures. To preserve battery
life, the unit should remain
plugged into an AC outlet.
As the battery gets older, its
voltage drops and memory may
be lost. Be sure to replace the
battery periodically. Battery
should be removed if the unit
will be stored for more than
one month. Leaky battery can
badly damage the clock radio.
The AC power plug is
polarized (one blade is
wider than the other)
and only fits into AC
Date of Purchase:
Place of Purchase:
Serial No.:
When the battery backup
functions, the digital display will
not light, however, the wake
function still occurs during the
power interruption if remaining
battery power is adequate.
power outlets one way.
Technical information
Product: Clock Radio
Brand: RCA
Model: RP5415/RP5415PK
Power Supply: 120V ~ 60Hz
Power Consumption: 4 Watts
If the plug will not go into the
outlet completely, turn the plug
over and try to insert it the other
way. If it still does not fit, contact
a qualified electrician to change
the outlet, or use a different one.
Do not attempt to bypass this
safety feature.
•
•
Normal operation will resume
after AC power is restored so you
will not have to reset the time or
wake.
Caution marking is located at
bottom of apparatus.
This is CLASS II apparatus
with double insulation,
and no protective earth
provided.
Install battery as follow:
1. Remove battery compartment
door (located at the bottom of
the radio) by applying thumb
pressure to the tab on battery
door and then lift the door
out and off the cabinet.
2. Connect a 9-volt battery (not
supplied) to the connector
plug.
•
•
Discard any leaky or deformed
battery immediately. They
may cause skin burns or other
personal injury.
Please help to protect the
environment by recycling
or disposing of batteries
according to federal, state, and
local regulations.
Power is fed to the unit even
when it is not functioning. To cut
the power supply off, the power
cable must be unplugged.
•
Do not expose batteries to
excessive heat (for example,
by leaving them in sunlight or
close to fire).
3. Replace the compartment door.
Radio
General controls
Clock
Front view
Right view
Setting clock
Left view
Selecting between
analogue and digital clock
Press DISPLAY to select between
analogue and digital clock display.
Back view
Changing position of the power
cord may improve reception.
Switching on/off
Turn the clock setting knob
the back of the unit to adjust
on
Press to turn on or off the radio.
clock time. The time decrements
or increments will follow by a
faster rate when you turn and
hold the knob. The digital clock
shows and a clock icon flashes
on the display while you are
adjusting the time.
Built-In AFC – The Built In
Automatic Frequency Control
(AFC) works only on FM. It helps
reducing drift on FM reception
and keeping the radio locked in
on the FM station to which it is
tuned.
Switching band
Slide the BAND AM/FM switch on
the back of the unit to select FM
or AM band.
BAND AM/FM – selects radio
band
Tuning radio
Turn the TUNING knob on the
left of the unit to adjust radio
frequency.
– turns on or off the radio; turns
off the wake function
AUX ON/OFF – selects auxiliary
input mode
When tuning in FM stations, you
may notice that the station you
are tuning can be well-tuned on
two or three nearby points on the
dial. Always tune carefully at the
loudest and clearest point.
TUNING – selects radio frequency
+ VOLUME – – adjusts volume
Top view
– adjusts Wake 2 time
– adjusts clock time
– adjusts Wake 1 time
Antennas
Display brightness
– Slide to activate
Wake 1 settings and change Wake
1 mode:
– Slide to activate
Wake 2 settings and change Wake
2 mode:
AM Antenna – A built-in ferrite
rod antenna eliminates the need
for an outside antenna for AM
reception. Rotating the unit
slightly may improve reception of
distant AM stations.
Clock time and radio frequency
are displayed on the display area
at the front of the unit. You
can adjust the brightness of the
display by rotating BRIGHTNESS
on the back of the unit.
•
(wake to alarm) – selects
alarm as the waking mode
(wake to radio) – selects
radio as the waking mode
•
(wake to alarm) – selects
alarm as the waking mode
(wake to radio) – selects
radio as the waking mode
•
•
– BRIGHTNESS + – adjusts display
brightness
SLEEP – activates sleep function
• OFF – deactivates Wake 1
waking mode
• OFF – deactivates Wake 2
waking mode
FM Antenna – The power cord
acts as your FM antenna. The
power cord picks up moderate
to strong stations and eliminates
the need for an external antenna
in most strong signal areas. Be
sure the power cord is stretched
out to its full length. Do not
coil or bunch the cord together.
SNOOZE – turns off the wake
function temporarily; cancels the
sleep function
WAKE 1 CHECK TIME – checks
the waking time for Wake 1
WAKE 2 CHECK TIME – checks
the waking time for Wake 2
DISPLAY – switches between
analog and digital clock displays
AUX IN – jack for external audio
input
Sleep function
Auxiliary input
Wake function
Checking wake time
SmartSnoozeTM operation
This operation allows extra sleep
time after the wake function
is on. The alarm will be off by
pressing SNOOZE, SLEEP or
DISPLAY until the snooze period
is over. Snooze period can be
set between 1 and 30 minutes
(default: 9 min).
In sleep mode, you can set the
duration (up to 2 hours) before
the radio turn off automatically.
Setting wake time
This unit allows two wake times
to be set.
Connecting auxiliary
device
Connect your auxiliary audio
player (e.g. mp3 player) with an
audio cable (not included) to the
AUX IN jack on the left side of
the unit.
Switching off wake
function
Adjust the auxiliary
device to mid-range
volume and adjust the
If you set Sleep function
with low volume level
before going to bed, we
advise using Wake to alarm
mode.
•
Press WAKE 1 CHECK TIME
or WAKE 2 CHECK TIME on
the sides of the unit to check
respective wake time. Wake
time shows briefly on the
display.
Slide the switches on the sides
of the unit to OFF to switch off
respective wake function. The set
wake time will not be erased and
can be used the next day when
you switch on wake function
again.
•
•
•
Turn the wake time setting
knob or on the back
master volume by rotating
VOLUME knob on the unit.
Do not turn the volume of the
auxiliary device too high as this
may affect the sound quality.
For other playback operations,
control them on your auxiliary
device.
1. Press and hold SLEEP and turn
the clock setting knob
on
of the unit to adjust wake
time 1 and 2 respectively.
The time decrements or
increments will follow by a
faster rate when you turn and
hold the knob.
“WAKE 1” or “WAKE 2” icon
flashes on the display while
you are adjusting respective
wake time.
the back of the unit to adjust
the duration up to 2 hours.
The time decrements or
increments will follow by a
faster rate when you turn and
hold the knob.
•
“OFF” shows on the display
if no wake source is selected
while you are checking the
wake time.
Selecting AUX IN mode
•
Press AUX ON/OFF on the
back of the unit to select AUX
IN mode.
Set the “quiet” period as follow:
1. Press and hold SNOOZE.
2. Turn the clock setting knob
on the back of the unit to
adjust the snooze “quiet”
period (default: 9 min). The
time decrements or increments
will follow by a faster rate
when you turn and hold the
knob.
•
Note: The radio will be
switched on.
Turning off the wake
alarm or radio
•
Press AUX ON/OFF again to
exit from the AUX IN mode
and resume to standby mode.
To listen to the radio again,
2. To check the remaining
•
Press SNOOZE on the top of
the unit. The wake alarm or
radio will be switched off
temporarily. The alarm or
radio will be on again when
the snooze period is over. (see
“SmartSnoozeTM Operation”)
To turn off the wake alarm
duration before the radio turns
off, press and hold SLEEP.
3. To cancel the sleep function,
Selecting wake source
You may be woken up by radio
or alarm.
1. Select an AM or FM station
(see directions on “Radio”).
2. Set a wake time (see above
direction).
press
.
press SNOOZE or
.
•
or radio completely, press
.
3. Slide the switches on the sides
The wake alarm or radio will
activate again the next day
unless you switch off the wake
function (see “Switching off
wake function”).
of the unit to
by alarm) or
/
(wake
(wake
/
by radio). Corresponding icon
lights on the front of the unit.
– Wake 1 by alarm
– Wake 1 by radio
– Wake 2 by alarm
– Wake 2 by radio
Warranty information
12 Month Limited Warranty
Applies to RCA Audio/Video
Products
interruptions of broadcast
or internet service, to costs
incurred for installation,
THE PURCHASE PRICE PAID
BY PURCHASER FOR THE
PRODUCT.
This Warranty is in lieu of
all other express warranties
or liabilities. ANY IMPLIED
WARRANTIES, INCLUDING
ANY IMPLIED WARRANTY
OF MERCHANTABILITY,
SHALL BE LIMITED TO THE
DURATION OF THIS WRITTEN
WARRANTY. ANY ACTION FOR
BREACH OF ANY WARRANTY
HEREUNDER INCLUDING ANY
IMPLIED WARRANTY OF
MERCHANTABILITY MUST BE
BROUGHT WITHIN A PERIOD
OF 24 MONTHS FROM DATE
OF ORIGINAL PURCHASE.
IN NO CASE SHALL THE
COMPANY BE LIABLE FOR
ANY CONSEQUENTIAL OR
INCIDENTAL DAMAGES FOR
BREACH OF THIS OR ANY
OTHER WARRANTY. No person
or representative is authorized
to assume for the Company
any liability other than
expressed herein in connection
with the sale of this product.
Some states do not allow
limitations on how long an
implied warranty lasts or the
exclusion or limitation of
incidental or consequential
damage so the above
limitations or exclusions
may not apply to you. This
Warranty gives you specific
legal rights and you may also
have other rights which vary
from state to state.
LOST CONTENT OR DATA, OR
FOR THE SECURITY OF ANY
PERSONAL CONTENT OR DATA
ON THE RETURNED DEVICE.
Product will be returned
with factory default settings,
and without any pre-loaded
content which may have been
installed in the originally
purchased products. Consumer
will be responsible for
reloading data and content.
Consumer will be responsible
to restore any personal
preference settings.
Properly pack your unit.
Include any remotes, memory
cards, cables, etc. which were
originally provided with the
product. However DO NOT
return any removable batteries,
even if batteries were included
with the original purchase. We
recommend using the original
carton and packing materials.
Include evidence of purchase
date such as the bill of sale.
Also print your name and
Audiovox Electronics Corp.
Attn: Service Department.
150 Marcus Blvd.
Hauppauge N.Y. 11788
1-877-833-3491
•
AUDIOVOX ELECTRONICS
CORP. (the Company) warrants
to the original retail purchaser
of this product that should
this product or any part
removal or reinstallation of
product, to corruptions caused
by computer viruses, spyware
or other malware, to loss of
media, files, data or content,
or to damage to tapes, discs,
removable memory devices or
cards, speakers, accessories,
computers, computer
peripherals, other media
players, home networks or
vehicle electrical systems.
This Warranty does not
apply to any product or
part thereof which, in the
opinion of the Company, has
suffered or been damaged
through alteration, improper
installation, mishandling,
misuse, neglect, accident, or by
removal or defacement of the
factory serial number/bar code
label(s). THE EXTENT OF THE
COMPANY’S LIABILITY UNDER
THIS WARRANTY IS LIMITED TO
THE REPAIR OR REPLACEMENT
PROVIDED ABOVE AND,
•
•
Insure your shipment for loss or
damage. Audiovox accepts no
liability in case of damage or
loss en route to Audiovox.
Pay any charges billed to you by
the Exchange Center for service
not covered by the warranty.
A new or refurbished unit
will be shipped to you freight
prepaid.
thereof, under normal use and
conditions, be proven defective
in material or workmanship
within 12 months from the
date of original purchase, such
defect(s) will be repaired or
replaced with reconditioned
product (at the Company’s
option) without charge for
parts and repair labor.
•
•
How to make a warranty
claim:
If your product is capable
of storing content (such
as an mp3 player, digital
voice recorder, etc), it is
•
•
•
recommended to make
What we will do:
•
To obtain repair or
periodic backup copies of
content stored on the product.
If applicable, before shipping a
product, make a back up copy
of content or data stored on
the device. Also, it is advisable
to remove any personal
content which you would not
want exposed to others. IT IS
LIKELY THAT CONTENTS AND
DATA ON THE DEVICE WILL BE
LOST DURING SERVICE AND
REFORMATTING. AUDIOVOX
ACCEPTS NO LIABILITY FOR
Provide you with a new, or at our
option, a refurbished unit. The
exchange unit is under warranty
for the remainder of the original
product’s warranty period.
replacement within the terms
of this Warranty, the product
is to be delivered with proof
of warranty coverage (e.g.
dated bill of sale), specification
of defect(s), transportation
prepaid, to the Company at
the address shown below.
This Warranty does not
Audiovox Electronics Corp.
150 Marcus Blvd,
For Canada Customers, please
ship to:
Audiovox Return Centre
c/o Genco
6685 Kennedy Road,
Unit#3, Door 16,
Mississuaga, Ontario
L5T 3A5
Hauppauge, NY 11788
•
©2009 Audiovox Electronics Corp.
Trademark(s) ® Registered
Marque(s) ® Deposée(s)
Marca(s) ® Registrada(s)
Printed in China
•
extend to the elimination
of externally generated
static or noise, to correction
of antenna problems, loss/
address and a description of
the defect. Send via standard
UPS or its equivalent to:
IN NO EVENT, SHALL THE
COMPANY’S LIABILITY EXCEED
•
Download from Www.Somanuals.com. All Manuals Search And Download.
|