QFT5D INSTRUCTIONS 10/5/06 10:27 AM Page 1
®
Qflash
“5d-R” series
Digital Flash
Models QFT5d-R, QFX5d-R
Operating Instructions
QFT5d-R-- powered by Quantum Turbo® batteries
QFX5d-R-- powered by Quantum Qpaq System
Quantum Instruments
Designed and manufactured in the USA
Download from Www.Somanuals.com. All Manuals Search And Download.
QFT5D INSTRUCTIONS 10/5/06 10:27 AM Page 3
Download from Www.Somanuals.com. All Manuals Search And Download.
QFT5D INSTRUCTIONS 10/5/06 10:27 AM Page 4
Flash Display Symbols
Speaker
Flash indicator LEDs
On solid - Flash ready
Blinking - Flash recycling
Front curtain sync
Rear curtain syns
Reflector in normal
Bare bulb reflector
Reflector with diffusing disks,
wide angle dome, or soft box
Telephoto reflector
Auto sensor limit turned off
Download from Www.Somanuals.com. All Manuals Search And Download.
QFT5D INSTRUCTIONS 10/5/06 10:27 AM Page 5
TABLE OF CONTENTS
Section
1.0
Description
Introduction
2.0
Warnings
3.0
Advanced Features Summary
4.0
Features available with QTTL
(D, Dw, Dw-R series) Adapters
5.0
6.0
Getting Started
Basic Navigation
7.0
Common Features
8.0
Basic Options
9.0
Manual Mode Operation
Automatic Mode Operation
TTL and QTTL Mode Operation
Stroboscopic Mode Operation
Program Mode Operation
Wireless Qflash Operation
Wired Control Mode
10.0
11.0
12.0
13.0
14.0
15.0
16.0
Typical Lighting Situations
1. INTRODUCTION
Qflash “5d-R” series flashes provide professional quality lighting for both
digital and film cameras. Quantum’s proprietary QTTL® Adapters dedicate
Qflash seamlessly to your camera. Many features of Qflash5d-R will
enhance your lighting control when used with non-dedicated/manual
cameras.
While powerful and extremely versatile, Qflash operation is intuitive and
straightforward. Advanced features for most lighting needs are accessible
as required.
We highly recommend reading this entire instruction manual.
Whether or not you require all of Qflash’s capability now, you will
want to know it exists when the need arises.
Series Qflash 5d-R adds wireless preflash TTL and wireless remote auto
to the Qflash features. These features apply when Qflash 5d-R is used in
combination with Dw-R series QTTL Adapters, FreeXWire receivers
FW7Q and FW8R, and transmitter FW9T or transceiver FW10w. If you
own FW10 transceivers, they can be upgraded to become FW10w.
Qflash 5d-R models used with Quantum’s proprietary Dw-R Adapters
allow you to create ratios with multiple remote Qflashes in the wireless
TTL mode. Older D and Dw series Adapters can be upgraded to become
Dw-R adapters.
QTTL adapters are optional for specific makes and camera models.
.
1
Download from Www.Somanuals.com. All Manuals Search And Download.
QFT5D INSTRUCTIONS 10/5/06 10:27 AM Page 6
2. WARNINGS AND CAUTIONS
• Disconnect external power before changing the flash tube, or
connecting or disconnecting to/from cameras, power packs,
or any other equipment.
• OPERATE ONLY WITH A FLASH TUBE IN THE SOCKET!!
• DO NOT TOUCH THE FLASH TUBE SOCKET WITH METAL
OBJECTS!!
• THIS IS A PROFESSIONAL INSTRUMENT. KEEP AWAY
FROM CHILDREN!!
• DO NOT ATTEMPT TO OPEN THE FLASH UNIT! DANGEROUS
HIGH VOLTAGE INSIDE!!
• Repairs can be made only by a qualified Quantum service
representative.
3. ADVANCED FEATURES SUMMARY
The chart below summarizes the advanced features for various Qflash
series. A “U” means the Qflash model will have this feature when upgrad-
ed to series 5d-R. An “F” means this feature is available in the model
shown.
Feature
Qflash Models (T and X types)
QF4d
QF5d
QF5d-R
Wireless Control in Nikon/Canon
systems with Qnexus
U
U
F
Wireless multiple ratio TTL- with
Dw-R Adapters & FreeXWire
U
U
F
Wireless preflash TTL with digital cameras
-using Dw/ Dw-R Adapters and FreeXWire
U
U
U
F
F
F
F
F
F
F
F
F
Wireless remote Auto / Auto Fill mode
Zone control of FW7Q from panel of Qflash
Flash ready indication in camera viewfinder
Shutter speed control
(camera detects flash and sets shutter)
F
F
F
F
F
F
F
F
F
F
F
F
Rear Curtain Sync
Auto focus assist
Auto Fill ratio
2
Download from Www.Somanuals.com. All Manuals Search And Download.
QFT5D INSTRUCTIONS 10/5/06 10:27 AM Page 7
4. FEATURES AVAILABLE WITH QTTL
(D, Dw, Dw-R SERIES) ADAPTERS
Quantum’s QTTL® adapters provide a dedicated link between Qflash 5d-R
series and popular digital and film cameras.
Wireless multiple ratio TTL - with Dw-R series Adapters & FreeXWires,
remote Qflashes can be set to ratios of the camera’s TTL metering
system. For example, an on-camera flash could be set 1.6 stops down, a
main flash on the left to +1 stop, and a hairlight to –2 stops from the
camera TTL exposure.
Wireless preflash TTL with digital cameras - when using Dw or Dw-R
series QTTL Adapters, you can control Qflash exposure wirelessly with
your camera’s TTL exposure control system.
Rear curtain sync - If supported by your camera, the QTTL adapter can
fire Qflash in sync with the rear curtain. Rear curtain sync is selected by
a switch located on the back of the adapter.
Auto focus assist - If your camera requires an infrared focus assist, the
QTTL adapter will project a beam when the camera focuses.
Flash Sync speed control - If flash readiness is achieved, the camera’s
automatic system switches the shutter speed to the correct flash sync
speed.
Ready light - Flash readiness is established when the “Ready” indicator
appears in the Qflash display. If “flash ready” is supported by the camera,
then a flash symbol will appear in the viewfinder when Qflash is recycled
and ready.
Pre-flash TTL - Cameras that have advanced TTL metering systems
require a pre-flash to determine proper exposure. This pre-flash is sup-
ported by the QTTL adapters.
QTTL adapters support the features mentioned above only when the
camera connected also supports those features. Please see the list of
adapters available for cameras in the latest Quantum Price List or at
3
Download from Www.Somanuals.com. All Manuals Search And Download.
QFT5D INSTRUCTIONS 10/5/06 10:27 AM Page 8
5. GETTING STARTED
5.1 Inserting the Flash Tube
Match the red dot on the base of the flash tube with the red dot in the sock-
et of Qflash. Push the flash tube in until it is seated snugly into the socket.
Excessive force is not required.
Replace the flash tube only with Quantum type QF30 or QF30uv for Qflash
model T5d / T5d-R. Qflash model X5d / X5d-R requires QF32 or QF32uv
flash tubes. Other flash tubes will not provide proper exposure, may not
work at all, or they may damage the Qflash.
5.2 Reflectors and Bare Bulb
Reflectors are secured by the locking
ring near the base of the reflector.
Rotate the ring in the directions
shown in the diagram to loosen or
tighten the reflectors.
When inserting a reflector, first slowly r
it until the notch in the reflector “drops
into head of the Qflash. Then tighte
locking ring. If you do not let the reflec
fully into the Qflash before locking it, th
may become loose during use.
Approx.
Angle
Guide No. for ISO 200*
QFT5d-R QFX5d-R
200Ws
Reflector
400Ws
226ft / 72m 226ft / 72m 320ft / 100m
Normal QF60
55˚
70˚
QF60 w/ flat diffuser
128ft / 40m 128ft / 40m
180ft / 56m
180ft / 56m
128ft / 40m
QF67A Dome Diffuser
QF68 Soft Box
QF69 Mini Soft Box
90˚
128ft / 40m 128ft / 40m
QF62Bs/g Bare Bulb Reflector
QF63B Tele Reflector
120˚
20˚
90ft / 28m
90ft / 28m
453ft / 143m 453ft / 143m 640ft / 202m
Note to previous Qflash T, T2 ,X or X2 owners: There is no longer a “Wide”
position for the reflectors. The only position is “Normal”. For wide angle
coverage, use the included flat diffusers, or
optional QF67A wide angle or Soft B
QF68 diffusers.
5.3 Bounce and Swivel Head
The head position is locked and can
be changed with a single button (see
diagram). Press and hold this button, th
adjust the head to the desired position.
the button, and slightly move the head u
“clicks” and locks the head into the verti
horizontal planes.
4
Download from Www.Somanuals.com. All Manuals Search And Download.
QFT5D INSTRUCTIONS 10/5/06 10:27 AM Page 9
5.4 Bracket Mounting
Qflash mounts with a 1/4-20 standard tripod thre
ets, light stands, and tripods. Many brackets
especially for Qflash by popular bracket manufa
Quantum has two optional brackets, mode
QF70US and QF70E. The instructions below
describe mounting to both of these brackets
and to other manufacturers brackets, light
stands, and tripods.
Two types of 1/4-20 fasteners screw/knob and
a friction pad are supplied with Qflash. Place
the friction pad between Qflash and the bracket
insert the knob/screw and tighten. (If the moun
surface has a pad, the friction pad is not nec
Note: Brackets vary in thickness - always make sure that
the mounting knob/screw screws into Qflash at least two complete turns.
5.5 Connecting Qflash to a Camera
There are two ways to connect a Qflash to a camera- wired and wireless.
For wired connection use either of these methods:
• Connect a household two-prong sync cord (supplied) to the sync
connector of Qflash.
• Connect a QF series TTL adapter to the camera hot shoe.
• Connect a D, Dw, or Dw-R series QTTL adapter to the camera hot shoe.
• Connect a QF53 Hot Shoe sync to the camera.
For wireless connection
• Use the FreeXWire system. See Section 14 - Wireless Qflash Operation
adapter models.
Note: When using a household type (two-prong) sync cord, if you have
difficulty getting the flash to fire, Remove the two-prong plug from the
Qflash and reinsert it in the opposite direction. This changes the polarity
of the Qflash to match the polarity of the camera.
5.6 Powering Qflash
Before turning on any power to Qflash always make all electrical
connections first, both to the camera and to the power pack. Qflash
“T” models are powered by any Quantum Turbo Battery including Turbo
2x2, Turbo Compact, Turbo Z, and Turbo SC. Quantum “X” models are
powered by the Quantum Qpaq system.
Plug the Qflash power cable into the output connection of the appropriate
power pack. Turn on Turbo or Qpaq power. Normally Qflash will be pow-
ered up and ready to run.
If a “Check Turbo” or “Check Power” message appears on the Qflash
display, turn off the Turbo or Qpaq, wait one second, and turn it on again.
If the message appears again, the power pack needs recharging. If a
“Reset Flash?” message appears in the Qflash display press any button,
except the Mode I button, to resume operation.
5
Download from Www.Somanuals.com. All Manuals Search And Download.
QFT5D INSTRUCTIONS 10/5/06 10:27 AM Page 10
6. BASIC NAVIGATION
This Section explains how to maneuver your way around the
Qflash 5d-R
Very Important Tips
For consistent exposures with your digital camera and Qflash.
• Always do a custom white balance before shooting
• When shooting TTL use Aperture or Shutter priority or Manual
camera modes
• Set your metering area to center weight, partial metering
instead of matrix or multi-spot metering.
• Your Qflash provides 150 watt-seconds of power compared to
50 watt-seconds of a typical shoe mount flash. When shooting
6 ft. (2m) or closer, at ISO 200 or greater, with a wide open F/#,
you must always diffuse the light. Otherwise your subject will
be over-exposed.
6
Download from Www.Somanuals.com. All Manuals Search And Download.
QFT5D INSTRUCTIONS 10/5/06 10:27 AM Page 11
7. COMMON FEATURES
7.1 Flash Ready
The Flash Ready indicator will
blink while Qflash is recycling. It
will stop blinking once the flash
is ready to fire again, and the
speaker will beep.
If flash readiness is supported by the camera, then an LED or flash sym-
bol will appear in the viewfinder when the flash is ready. Many cameras
will automatically switch the shutter to the camera pre-defined flash sync
speed.
7.2 Display, Speaker, and Indicator Lights
Qflash indicates the result of a flash exposure in Automatic and TTL/QTTL
modes via the Display, Speaker and Flash Indicator Lights. The signals
are shown in the table below:
Flash exposure
condition
Speaker/
Earphone
Flash
Display
OK
Indicator Lights
Good exposure
Under/Over
one beep
3“beeps
rapid blink
Undr or Over
3 blinks, pause,
3 blinks, pause…
No flash
No Flash
long steady beep
long steady on
7.3 Sync Turn Off
If you are using Qflash as an on camera flash and want to disable the
flash for a few shots, you can use the ‘sync turn off’ feature. To prevent
Qflash from firing, press Mode I twice. The word ‘OFF’ will appear in the
display. To return to normal operation press any button (except Test M ).
Other Qflashes connected to this on-camera flash, whether by cable or
wirelessly, will fire (unless they also are turned off).
This feature will only prevent the flash from firing, it will not turn off the
Qflash or the Turbo. To completely turn off the Qflash the Turbo must be
turned off.
7.4 Rear Curtain Sync
When using a QTTL Adapter, Qflash can fire the flash with the rear cur-
tain (if supported by your camera). Rear curtain sync is selected with the
switch located on the back of the QTTL Adapter. Set it to “R” for rear cur-
tain, or “F” for front curtain. For some cameras rear curtain is controlled
through a menu on the camera itself. For these cameras leave the switch
in the “F” position. Consult your camera’s manual.
7
Download from Www.Somanuals.com. All Manuals Search And Download.
QFT5D INSTRUCTIONS 10/5/06 10:27 AM Page 12
7.5 Auto Focus Assist
The D/Dw/Dw-R series QTTL Adapters will project a beam whenever the
camera is having difficulty focusing due to low light conditions. A local
Qflash must be connected for this feature. Turn the auto focus assist
switch of the QTTL Adapter to on ( ).
Always turn the auto focus assist switch off (■) under any of the following
conditions:
When no Qflash is connected;
When using Qflash models, T, T2, X or X2. These models do not
support auto focus assist;
When using a QF50 or QF51 extension cables.
If the auto focus switch is not turned off for the above conditions, proper
operation cannot be assured.
8. BASIC OPTIONS
You can cycle through the option menus in this section by pushing
the Option ■ button. Then select an option to change by pressing the
Set G button until the option you want to change blinks. Then use the
Up J/Down L buttons to make the change.
Option Menu 1:
8.1 Flash Sensor Limit for Auto Mode
Flash sensor limit is an option that limits the distance that the sensor
“sees” when the Qflash is in Auto mode. This option is described in detail
in section 10.
Speaker
You may want the speaker off for sensitive shooting, or turn it on for audi-
ble confirmation of flash exposure. The earphone signals always sound
whether the speaker function is set on or off.
Flash Indicator Lights
The red Flash Indicators on four sides of Qflash give visual indication that
a flash fired, weather the exposure was good, over, under, or no flash, indi-
cating that the flash did not fire. You can enable or disable the lights.
Reflector settings
Setting the reflector type is important so that the displayed distance, guide
number and f/# correspond to the reflector in use. The choices are NORM
(for the reflector supplied with Qflash), DIFF (for diffusers supplied with
Qflash, and optional QF67A wide-angle diffuser or softbox QF68), BBE
8
Download from Www.Somanuals.com. All Manuals Search And Download.
QFT5D INSTRUCTIONS 10/5/06 10:27 AM Page 13
(optional Bare Bulb Enhancers QF62Bs and QF62Bg) and TELE (for
optional QF63B Tele photo reflector). The reflectors must be repositioned
manually.
Notes:
When using QF62B s/g the manual parameters are accurate only for an
open area. In medium and small rooms the very widely dispersed light will
bounce off nearby walls and increase exposure. A practical solution when
using QF62B in small rooms is to meter the light, or use Auto, TTL, or QTTL
modes which will provide better exposures and attractive, soft lighting.
When using a Telephoto Reflector QF63B the Auto mode cannot be used
because the flash sensor is blocked. Use Manual, TTL, QTTL, Strobo or
Linked modes.
Use “B” series reflectors (QF61B, QF62B g/s, QF63B) with Qflash 5d-R.
The standard QF60B reflector mounts to Qflash 5d-R as well.
Distance Units
Set your preference for the display of metric (M) or US distance (Ft) units.
Guide numbers also change accordingly.
8.2 Option Menu 2:
Exposure Compensation
Quantum calibrates Qflashes to American National Standards Institute
(ANSI) standards with laboratory equipment traceable to the National
Institute of Standards and Technology (NIST). From time to time, photog-
raphers may wish to fine tune Qflash exposures to match their exposure
meters, to compensate for variations in cameras or films, to match partic-
ular styles, for effects, or for individual taste.
There are two compensations available- one for Manual and one for
Auto mode. In QTTL modes Qflash does not control exposure and
compensation will not apply. The compensation also does not apply
whenever Wireless or Wired appears in the display.
8.2.1 Setting Compensation
Press Set G until the compensation you wish to change blinks. Adjust com-
pensation Up J/Down L in 1/3 steps up to +2 or -2 stops. All exposures
for that mode will be compensated by the amount selected. You cannot limit
compensation settings to individual programs in program mode.
For calibration to a particular light meter you may use the procedures
below. It is very important to note the meter measurement type
(incident, reflected) used for each procedure!
9
Download from Www.Somanuals.com. All Manuals Search And Download.
QFT5D INSTRUCTIONS 10/5/06 10:27 AM Page 14
8.2.2 Manual mode Qflash Compensation
This procedure will calibrate
Qflash to an incident light flash
meter you use and trust. Note
that only incident light measure-
ments are reliable for manual
exposure settings.
1. Place the Qflash 10 feet from the incident light flash meter facing
Qflash.
2. The area surrounding the meter and flash should be similar to the
shooting environment you usually work in. For example, in a large hall,
there will be little light bouncing from walls and ceilings. In a small room,
the light meter reading will be increased by whatever bounce occurs
from nearby surfaces. These factors will affect calibration and should be
considered.
3 Turn Qflash on and change the manual power setting to 1/8.
4. Set the film speed on the flash and the flash meter to the same value.
5. Change the F number on the flash until the distance shown in the
display is 10 feet.
6. Fire Qflash. Push the the Option ■ button, until the compensation
display appears.
7. Use the Set G and Up J/Down L buttons to adjust compensation until
the f/number in the display matches the f the f/number on the meter.
The light output can be increased or decreased by as much as 2 stops
in 1/3 steps.
8.2.3 Auto mode Qflash Compensation
This procedure will calibrate Qflash to a reflected light flash meter you use
and trust. Note that only reflected
light measurements are reliable for
auto exposure settings.
This is because auto mode flash-
es read reflected light from the
scene and subject. In order to
compare those readings to
a meter, the meter must also be
reading the same reflected light.
The reflected light is affected by
the subject and background, and an incident light reading will not typically
provide the same reading (unless the subject is an 18% gray card).
1. Place the Qflash 10 feet from a blank wall. The wall should be larger
than the metering area of the meter, and preferably a wall of continuous
tone (blank wall).
2. Place flash meter next to Qflash, also facing the blank wall. Be sure to
set the flash meter for a reflected reading.
3. Turn Qflash on and change the f/ number to F8.0
4. Set the film speed on the flash and the flash meter to the same value.
10
Download from Www.Somanuals.com. All Manuals Search And Download.
QFT5D INSTRUCTIONS 10/5/06 10:27 AM Page 15
5. Fire Qflash. Push the the Option ■ button, until the compensation dis
play appears.
6. Use the Set G and Up J button to increase light output (if flash meter
reads less than F 8.0), or the Down L button to decrease light output
(if flash meter reads more than F 8.0). The light output can be increased
or decreased by as much as 2 stops in 1/3 steps.
8.3 Option Menu 3
FW7Q Zone Control
This option menu is only available when a FW7Q is attached to the Qflash.
With this option menu you can access the zone and the range settings of
the FW7Q.
You can enter this menu by pushing the Option ■ button until it shows up
on the Qflash’s display. The Set G button will cycle through the available
settings. Use the Up J/Down L buttons to make a change.
8.4 Restoring Factory settings
Qflash options and settings are preset at the factory. You can restore the
factory settings by the following method:
1. Turn Turbo or Qpaq OFF. Connect Qflash to Turbo or Qpaq.
2. Press and hold any button (except Test M ).
3. Turn Turbo or Qpaq ON.
4. The Qflash will display a reset message.
5. Press Mode I to reset the Qflash and restore the factory settings.
If you push any other button or fail to push the Mode I button within 4 sec-
onds, the Factory settings will not be restored.
11
Download from Www.Somanuals.com. All Manuals Search And Download.
QFT5D INSTRUCTIONS 10/5/06 10:27 AM Page 16
9. MANUAL MODE OPERATION
The camera exposure may be set to any mode, and Qflash will emit
the fixed amount of light shown on its display.
9.1 Manual Mode with sync only connection
Power, F/number, ISO are all user adjustable. The Set G button will cycle
through them in that order.
Power settings are adjustable in 1/3 steps from full power to 1/64th power
like this: 1/1, 1/1-, 1/2+, 1/2 ,1/2- …… 1/32, 1/32-, 1/64+, 1/64. Using ISO
and Aperture settings, Qflash calculates the optimal flash distance. Match
these settings to your camera’s film speed and aperture.
Flash Compensation setting allows you to fine tune your Qflash in manu-
al mode from +2 to –2 stops in 1/3 step increments.
For model X5d-R only there is an additional Manual setting for 200/400
watt seconds, which can be set in the option menu.
12
Download from Www.Somanuals.com. All Manuals Search And Download.
QFT5D INSTRUCTIONS 10/5/06 10:27 AM Page 17
9.2 Manual mode with QTTL adapter connection
With a QTTL adapter the camera controls the f/# and ISO shown on the
display - you cannot change it on Qflash. The camera also selects its shut-
ter speed consistent with flash exposure. The camera exposure may be
set to manual, aperture or shutter priority.
The power level is set on the Qflash. Qflash will emit the fixed amount of
light shown on its display, and the distance shown corresponds to the sub-
ject distance for good exposure for the f/# set on the camera.
The following QTTL features are available: Front or Rear curtain sync,
Auto focus assist, and Ready light.
9.3 Manual shooting made easy
Nothing can beat the combination of a flash meter and a flash set manu-
ally. Automatic and TTL are a compromise based on the need for speed.
Setting the flash for a manual power setting and taking an incident meter
reading takes time and resources the average photographer may not
have. So we use automatic flash exposure and know that in some situa-
tions the sensor may be fooled.
The Qflash 5d-R allows for easy manual shooting without metering. Below
is an example of how this is accomplished.
In this example Qflash will produce an F8.0
at the subject (8 ft), and it will be quickly
accomplished without metering.
Start by selecting the F number and Film
speed you are using on your camera. If you
have connected a QTTL adapter these are
already chosen for you. Now adjust the
power setting until the Qflash distance
shown matches the subject distance as
closely as possible.
13
Download from Www.Somanuals.com. All Manuals Search And Download.
QFT5D INSTRUCTIONS 10/5/06 10:27 AM Page 18
Reminder: If the distance to the subject changes (you move in for a head
shot, or move out for a full length) you must change the flash distance
readout by changing the power setting.
10. AUTOMATIC MODE OPERATION
The preferred setup for Auto Mode is to connect Qflash to a camera
with a QTTL (D, Dw, or Dw-R series) Adapter. Then, the ISO and f/#
settings of the camera are set and displayed on the Qflash panel.
Qflash will display “Auto Fill” indicating that fill/flash ratio may be
set on the QTTL Adapter. The camera may be set to manual, shutter
or aperture priority, however light output is controlled by Qflash.
10.1 Automatic Mode with Sync only Connection
Using only a plain sync cord, Qflash displays “Auto” Mode. F/# and
ISO are set on the Qflash display manually. Press Set G to select
f/#, then press the Up J/Down L keys to change the setting. Similarly,
press Set G twice to select ISO and change it.
Flash distance displays the working distance between your Qflash and
Subject based on the current settings. Moving outside this range may
result in an Under or Overexposed picture.
14
Download from Www.Somanuals.com. All Manuals Search And Download.
QFT5D INSTRUCTIONS 10/5/06 10:27 AM Page 19
10.2 Auto mode exposure indications
There are three types of exposure indications. The display will blink either
OK, Over, or Undr. The display will also indicate how much over or under
the last exposure was, from +3 stops to -3 stops. If an arrow appears then
the exposure error is more than 3 stops (for example -3
).
If activated in Options (Section 8.2) the Speaker will sound after a flash.
The audible signal is one “beep” for “OK and ready”, and three “beeps” for
“Undr” or “Over”.
10.3 Auto Fill (Auto mode with QTTL adapter)
Auto Fill is useful when you prefer to control exposure with the Qflash
sensor, instead of a camera’s own TTL or pre-flash metering. Many
photographers find that Auto Fill mode provides more consistent expo-
sures for digital cameras.
Fill flash ratio may be set using the “Fill” dial on the QTTL adapter. Choose
any setting from –3 stops below to +2 stops above the camera’s aperture,
in 1/3 stop increments. As the aperture of the camera changes Qflash will
adjust it’s output to keep the ratio that has been selected.
15
Download from Www.Somanuals.com. All Manuals Search And Download.
QFT5D INSTRUCTIONS 10/5/06 10:27 AM Page 20
Error messages will appear if you choose a fill ratio which is out of range
of the flash. The error indications are:
“OUT OF RANGE - DECREASE FILL OR F#”
For example, the camera is set to F16 and QTTL fill flash is set to +2 stops.
Either decrease the f/# on the camera or decrease the fill flash ratio on the
QTTL adapter.
“OUT OF RANGE - INCREASE FILL OR F#”
For example, the camera is set to F2.8 and QTTL fill flash is set to –3
stops. Increase the f/# on the camera or increase the fill flash ratio on the
QTTL adapter.
Once the adjustment is made and Qflash returns to an acceptable range,
the display will revert to the usual Auto Fill information.
QTTL Fill Dial
10.4 Auto Sensor Limit
Setting Qflash to Auto exposure makes picture taking fast and easy.
However, an automatic flash has a flaw: the sensor on the flash expects
the subject to be wide, flat, and fill the view of the sensor. A person
standing against a wall fits this description; people in a catering hall or
in a park at night do not. When the background is located far behind the
subject, the automatic flash struggles to produce even lighting. The
result is often an over exposed subject, sometimes by as much as two
stops. When a photo lab develops film with a greatly over exposed sub-
ject, it will ‘print down’ to bring the flesh tones back into range. Or, time
will be spent adjusting a digital image, with the resultant loss of detail
and image quality.
To solve this problem use the Flash sensor limit.
16
Download from Www.Somanuals.com. All Manuals Search And Download.
QFT5D INSTRUCTIONS 10/5/06 10:27 AM Page 21
10.5 Setting the Sensor Limit:
Press Option ■ button to bring up this menu. Push Set G once. The sen-
sor limit will blink. Use Up J/Down L buttons to change the sensor limit.
The available limits are:
- No limit placed on sensor distance
∞
20ft / 6m,
15ft / 4m,
10ft / 3m,
5ft / 2m,
When the Flash Sensor Limit is set to the flash will produce the desired
f/# for a subject within the flash’s minimum and maximum flash distance.
∞
With Auto Sensor Limit turned on, a ‘Limit’ indicator is activated. After a
flash, if the subject’s distance exceeds the sensor limit currently set (5, 10,
15 or 20ft. / 2, 3, 4, 6m) the word ‘Limit’ will appear in the display. Three
beeps and/or 3 blink warning may also occur (if those features are set in
Options). If the subject is within the current sensor limit normal exposure
indicators (OK, Undr, Over) will apply.
10.6 Quick turn ON / OFF of Sensor Limit
There are times you may want to quickly change from a Sensor Limit dis-
tance, to no sensor limit [ ]. For example, at a wedding reception you
∞
may shoot close up from 5’ with no background, and next shoot a group
shot from 25’.
To set or cancel a sensor limit quickly: Press the Option ■ button until you
bring up the menu with the Sensor limit setting. Then, without pressing the
Set G button, use the Up J/Down L buttons to toggle between maximum
sensor limit [ ] and the last sensor limit set (in the procedure above).
∞
You can also use Program (Section 13) to preset the sensor limits you
want. Then, just toggle between them using the Up J/Down L buttons.
17
Download from Www.Somanuals.com. All Manuals Search And Download.
QFT5D INSTRUCTIONS 10/5/06 10:27 AM Page 22
10.7 Using the Sensor Limit
The flash Sensor Limit function essentially cuts down on the distance that
Qflash attempts to illuminate. See the examples shown below.
Open field
The subject is located 15 feet from the
camera. The background is an open
field in a park. By setting the Sensor
Limit to 15 feet, the flash will read only
the light from subjects within 15 feet,
ignoring anything further.
Two subjects separated by a gap
Sometimes two subjects are sepa-
rated by a gap. When this occurs the
sensor is ‘looking’ between the two
subjects and may miss them. The
Sensor Limit will correct for this by
reading only the light from objects
within the limit set, in this case, 15
feet. The light from objects further
away will be ignored.
With the Sensor Limit it is no longer
necessary for the subject to be cen-
tered in the frame. As long as the
subject is within the Sensor Limit it
will be lit properly.
18
Download from Www.Somanuals.com. All Manuals Search And Download.
QFT5D INSTRUCTIONS 10/5/06 10:27 AM Page 23
11. TTL and QTTL MODE OPERATION
TTL Mode
TTL mode may be used when the camera exposure is set to manual, aper-
ture or shutter priority, or program mode, and Qflash is connected to the
camera with a compatible QF series Adapter. The camera will determine
flash exposure. The listing for compatible QF series TTL adapters is avail-
generally not compatible with digital cameras.
The exposure indications for TTL mode are similar to those of Auto mode
with one exception. The amount of under or over exposure will not be
shown in the display.
QTTL mode
When using a D, Dw, or Dw-R series QTTL adapter, “TTL” is replaced by
”QTTL” on the Qflash display. QTTL mode has all the features of the Auto
Fill mode including adjustment of fill ratio. The difference is that QTTL
mode lets the camera, not Qflash, control exposure.
Set your camera to manual, aperture or shutter priority, or program mode
for QTTL dedication to Qflash 5d-R.
Some cameras allow compensation (+/-) for flash/fill ratio. Qflash 5d-R
flash/fill can also be set on the QTTL adapter using the “Fill” dial. Choose
any setting from –3 stops below to +2 stops above the camera’s aperture,
in 1/3 stop increments. When desiring flash/fill ratio use either the camera
setting or the QTTL adapter setting, but not both.
19
Download from Www.Somanuals.com. All Manuals Search And Download.
QFT5D INSTRUCTIONS 10/5/06 10:27 AM Page 24
12. STROBOSCOPIC MODE OPERATION
Press the Set G to cycle through Frequency, Number of Flashes, and
Strobo Power, in that order.
Connect a sync cord or any Quantum QF, D, Dw, or Dw-R series Adapter
to the camera. After the flash has finished firing a confirmation message
will be displayed. The flash will display the actual number of flashes fired.
Strobo is a manual exposure mode. Over and Under exposures are not
indicated.
13. PROGRAM MODE OPERATION
The Program mode allows you to store your favorite settings and set-ups
and then quickly recall them just by pressing the Up J/Down L buttons.
Program up to 8 Qflash set-ups of Manual, Auto, or TTL operation, includ-
ing settings for all parameters.
20
Download from Www.Somanuals.com. All Manuals Search And Download.
QFT5D INSTRUCTIONS 10/5/06 10:27 AM Page 25
Your Qflash is factory preset with several Programs (which you are free to
change). To view them, press Mode I, then Up J/Down L until you see
the Program mode displayed, like above. After the “P” stops blinking, press
the Up J/Down L buttons to switch to the next higher, or lower program
number. (Programs which have not been preset are considered “clear” and
will be skipped).
How to set up or change a Program
While in the Program mode, press the Set G button. The program number
will blink, and the Up J/Down L buttons will select the program number
you wish to set or change. All program numbers will be displayed this way,
even those that are “clear”.
Press Set G again (or press it twice if the Program number stopped blink-
ing). The mode (Manual, Auto, TTL, etc.) will be blinking. Up J/Down L
to select your flash mode for this program.
Once your flash mode is selected keep pressing Set G to choose param-
eters to program. To change any settings use the same procedures used
for Manual, Auto, TTL, or Wireless/Wired modes.
There are times when you will want to “clear” a Program from memory.
Clearing unwanted programs allows for quicker switching between
stored programs during actual shoots. For example, if you need just
3 Programs for a job, and you clear out the other 5 Program numbers,
you will cycle through just the 3 Programs you want for a shoot, using the
Up J/Down L buttons.
To clear out a Program
Start in the Program number you wish to clear. Press Set G until
the ‘mode’ blinks in the display. Press Up J/Down L until the word
CLEAR appears. After several seconds the display will stop blinking
and the program will be cleared from memory. Note: You can never clear
out Program 1.
14. WIRELESS QFLASH OPERATION
WITH FreeXWire
Qflash 5d-R are capable of wireless operation using one or more units
connected to FreeXWire radios. Depending upon your needs, select one
of the operating modes below. There are also additional combinations of
modes that are possible for Local and Remote wireless Qflash operation
which are detailed in the chart of Section 14.5
Important: Note the series of FreeXWires and QTTL Adapters indi-
cated in each setup to be assured of proper operation.
21
Download from Www.Somanuals.com. All Manuals Search And Download.
QFT5D INSTRUCTIONS 10/5/06 10:27 AM Page 26
14.1 QTTLw - Wireless TTL mode
QTTLw mode gives exposure control of all Qflashes to your camera’s pre-
flash evaluative TTL metering system. Both Local (on-camera) and
Remote Qflashes will produce the same exposure. The Fill ratio can be
adjusted on the QTTL adapter (or on the camera, if available). However,
use only one Fill compensation at a time.
Set the camera modes: Choose manual, aperture priority, or shutter
priority on your camera. Program mode may be selected, although the
camera will make decisions that reduce your control of lighting.
14.1.1 A Local Qflash is optional.
If a local Qflash is attached to
the camera, Press Mode I, the
Up J/Down L until “QTTL” or
“QTTLw” appears on the display.
Note: “QTTLw” will appear after the
QTTL adapter has established com-
munication with the camera. This occurs when the camera shutter is
pressed 1/2 way.
14.1.2 Set up the Remote Qflash(s)
Connect a FreeXWire receiver to the
remote Qflash(s). FreeXWire model
FW7Q connects directly to Qflash;
models FW8R or FW10w require an
FW31 cable for connection.
Press Mode I on the Remote Qflash, then press the Up J/Down L but-
tons until the display shows “Linked to Local”.
14.2 QTTLwR - Wireless Multiple Flash Ratio TTL mode
QTTLwR mode provides the photographer with the ability to set three
zones of flash exposure, each with different amounts of exposure offset
from the camera’s TTL system. The three available flash zones are : Local,
Group R1, Group R2. Any number of Qflashes can be employed in each
of the 3 groups. For example, an on-camera flash could be set 1.3 stops
down (Local), two main flashes on the left to +1 stop (Group R1), and a
hairlight to –2 stops from the camera TTL exposure (Group R2). The actu-
al settings could be whatever you wish within +/- 3 stops.
22
Download from Www.Somanuals.com. All Manuals Search And Download.
QFT5D INSTRUCTIONS 10/5/06 10:27 AM Page 27
Set the camera modes: Choose manual, aperture priority, or shutter pri-
ority on your camera. Program mode may be selected, although the cam-
era will make decisions that reduce your control.
14.2.1 Always set up the Remote Qflash(s) first
Connect a FreeXWire receiver to
the remote Qflash(s). FreeXWire
model FW7Q connects directly to
Qflash; models FW8R or FW10w
require an FW31 cable for connec-
tion.
To set a Remote flash to the
Local group: Press Mode I, then
Up J/Down L until the display
shows “Linked to Local”. This
Remote Qflash exposure will be the
same as the Local, on-camera
Qflash.
To set a Remote flash to the Group
R1 or Group R2: Press Mode I,
then Up J/Down L until the dis-
play shows “Wireless Group R1”
or “Wireless Group R2”.
“QTTLwR” will appear on the
Remote display only when the Local Qflash is set up. If QTTLwR does not
appear press Mode I on the Local Qflash 3 times to re-sync the Local
Qflash with the Remotes. Also check that the FreeXWire units are con-
nected properly and turned on.
Continue setting all the Remote Qflashes to one of the three Groups.
There is no limit to the number of Qflashes in each Group.
14.2.2 A Local, on-camera flash is required
Press Mode I, then Up J/Down L until “QTTLwR” appears in the dis-
play. You have the ability to turn Remote flash Group R1 or R2, ON / OFF,
and the ability to set offset ratios for these groups. Note: “QTTLwR” will
appear after the QTTL adapter has established communication with the
camera. This occurs when the camera shutter is pressed 1/2 way.
Press the Set G button until ON/OFF next to flash Group R1, or R2, blinks.
Use the Up J/Down L buttons to turn the flash Groups ON or OFF. Next,
press the Set Gbutton until the offset amount blinks (0, -1, -13, etc.). Use
the Up J/Down L buttons to select the desired setting.
The Local Group flash ratio can be set with the Fill dial on the QTTL
Adapter. Use only series DwR QTTL Adapters. The amount of Fill offset
shows on the Local Qflash display.
23
Download from Www.Somanuals.com. All Manuals Search And Download.
QFT5D INSTRUCTIONS 10/5/06 10:27 AM Page 28
14.3 Wireless Auto Fill
Wireless Auto Fill mode has several useful features. It can add light ratio
capability to non-TTL cameras. With digital cameras Auto Fill mode can
decrease the delay between shutter release and image capture, compared
to the camera system’s TTL control. And, Auto Fill with Qflash sensor con-
trol lets the photographer fine tune flash exposure for her/his particular
needs without being locked into camera TTL exposure.
Set the camera modes: Manual, aperture priority, or shutter priority.
Program mode may be selected, although the camera will make decisions
that reduce your control of the shots.
14.3.1 A local, on-camera flash is optional.
To change the linked value Press the Set G button once. Use the
Up J/Down L buttons to select the desired option. To change the Fill
value use the Fill dial located on top of the QTTL adapter.
14.3.2 Set up the Mode of the Remote Qflash(s)
Connect a FreeXWire receiver to the
remote Qflash(s). FreeXWire model
FW7Q connects directly to Qflash; models
FW8R or FW10w require an FW31 cable
for connection.
To set a Remote flash to the Local
group: Press Mode I, then “Linked
to Local”. This Remote Qflash
exposure will be the same as the
Local, on-camera Qflash.
If you are not using a Local on-
camera Qflash: Press Mode I,
then Up J/Down L until the display
shows “Wireless Auto Fill”.
24
Download from Www.Somanuals.com. All Manuals Search And Download.
QFT5D INSTRUCTIONS 10/5/06 10:27 AM Page 29
14.4 Wireless Control Mode
Wireless Control mode can achieve the most control over wireless Remote
Qflashes. From the camera position you can change the modes, settings,
as well as the fill ratios, of Wireless Groups R1 and R2. Wireless Control
mode has the disadvantage, however, of being slower to react than
QTTLwR mode. This is because much more information has to be trans-
mitted to the Remote Qlfashes.
Use Wireless Control mode for maximum control over Remote Qflashes.
Select QTTLwR for faster reactions to changes in lighting ratios only.
14.4.1 A Local Qflash is required.
Press the Mode I button on
the Local Qflash and use the
Up J/Down L button to select
“Wireless Control.” The display will
show the data for Control (C) and
Group R1 and Group R2.
Next, from the Local Qflash panel, select the settings for the Remote
Qflashes.
•
Press Set G until either “C”, “R1” or “R2” blinks in the display.
If necessary, press Up _or Down _ until “R1” blinks to set the
parameters for Group R1, or until “R2” blinks for Group R2.
•
Press Set G again and the Mode of R1 or R2 will blink.
Use the Up J/Down L buttons to select the Mode of the Remote Qflash.
•
•
Press Set G again to set the parameters of the Mode selected.
Press Set G again and the word SEND will appear next to the data for
R1 or R2. The Control Qflash is now sending the data to the Remote
Qflash.
* A QTTLAdapter is not required. If one is used it provides all Qflashes with
ISO and F# setings from the camera. Set a fill/flash ratio (for the Control
Group only) with the “Fill” dial on the Adapter. Fill ratio applies only in TTL
and Auto modes.
25
Download from Www.Somanuals.com. All Manuals Search And Download.
QFT5D INSTRUCTIONS 10/5/06 10:27 AM Page 30
14.4.2 Set up the Remote Qflash Groups
Any number of Remote Qflashes may be used. Set each the Mode of each
Remote to either Wireless Group R1 or R2, or Linked to Local, using the
Mode I and Up J/Down L controls on each Remote Qflash.
The displays on the
Remote Qflashes will
update when the word
SEND appears on the
Local Qflash.
14.4.3 Wireless Control Mode – Important Notes
•
Qflash cannot fire while sending data to wireless Remotes, or when the
display is blinking. To speed up data transmission, press Set G on the
Control Qflash until SEND appears in the display to make Qflashes
ready.
•
When using a QTTL adapter, the camera settings for f/# and ISO will
appear on the Control Qflash display. Generally, to update the camera
settings, press the camera shutter 1/2 way (to wake up the camera or
metering function). The Qflash display will then update to the current
camera settings. (On some cameras updating takes place automatically).
26
Download from Www.Somanuals.com. All Manuals Search And Download.
QFT5D INSTRUCTIONS 10/5/06 10:27 AM Page 31
14.5 Available Modes and Features of Qflash Wireless Operation
In addition to the setups described in Section 14.1, 14.2 and 14.3, other
combination of modes are possible for Local and Remote Qlfashes. In the
table below, pay particular attention to the models of FreeXWires and
QTTL adapters required to achieve the results in the chart. We recom-
mend some testing when using one of the combinations of operating
modes before shooting an assignment.
27
Download from Www.Somanuals.com. All Manuals Search And Download.
QFT5D INSTRUCTIONS 10/5/06 10:27 AM Page 32
14.6 SYNC only setup
By employing this type of setup each Qflash operates independently of the
others. This is the simplest and most straightforward way of using multi-
ple, wireless Qflashes.
For independent Qflash operation the Qflashes must be in Manual,
Auto (Auto Fill), or Strobo. If any one of the Qflashes is in TTL, QTTL, or
Wireless, the Qflashes will no longer behave independently.
Example of independent Qflash operation
28
Download from Www.Somanuals.com. All Manuals Search And Download.
QFT5D INSTRUCTIONS 10/5/06 10:27 AM Page 33
15. WIRED CONTROL MODE
Qflash’s Wired Control Mode is a versatile tool for precise lighting control.
One Qflash is designated as the “Control”, and from its panel the photog-
rapher can change the modes or settings on one or two “Remote”
Qflashes.
The physical setup for Control Mode is shown below. The camera adapter
must be a QTTL series D, Dw, or Dw-R series:
Wired Control
The basic steps for Wired Control Mode setup are:
•
Set the on-camera flash to Wired Control. Usually this is the one at the
camera. Connect a QTTL Adapter (D, Dw, or Dw-R series).
•
Using the Control Qflash panel, select the operating Mode and settings
for Control, Remote 1 and/or 2.
15.1 Set up the Control Unit
The number of Qflashes can be 2 or 3. Turn on all Qflashes. The Qflash
displays will prompt you to select the Control flash for the “Wired Control”
setup. Press the Mode I button on the Qflash that you want to be the
Control Qflash (usually the one at the camera).
The display will change to ”Wired Control”, and show the data for Remote
1 ( R1 ) and Remote 2 ( R2 ).
29
Download from Www.Somanuals.com. All Manuals Search And Download.
QFT5D INSTRUCTIONS 10/5/06 10:27 AM Page 34
The displays of the two Remote Qflashes will automatically change to R1
and R2.
15.2
Select the Mode and settings for all flashes
Always select the settings you desire for the Control Qflash first. Those
settings determine the choices you have for the Remotes.
• Press Set G until “C” is blinking. (If “R1” or “R2” is blinking instead,
press the Up J/Down L buttons until “C” blinks).
• Press Set G again. The mode of the Control flash will blink.
Use the Up J/Down L buttons to select the mode. The choices are Man,
Auto, QTTL and OFF* (see 15.3 – Wireless Setup - Important Notes)
• Press Set G again to set the parameters for the mode selected. For
example, power (1/64 to 1/1) for Man, F# for Auto, etc. There are no
settings for TTL or OFF modes.
• Set the fill/flash ratio. To change the ratio, turn the “Fill” dial on the
QTTL adapter.
Next, from the Control Qflash panel, select the settings for the Remote
Qflash(s):
• Press Set G until either “C”, “R1” or “R2” blinks in the display.
If necessary, press Up J/Down L until “R1” blinks to set the
parameters for Remote 1, or until “R2” blinks for Remote 2.
• Press Set G again and the Mode of R1 or R2 will blink.
Use the Up J/Down L buttons to select the Mode of the Remote Qflash.
• Press Set G again to set the parameters of the Mode selected.
15.3 Selecting a different flash as the control flash
To select a different flash as the control, press the Mode I button on the
Control Qflash and use the Up J/Down L button. The Qflash displays will
prompt you to select the Control flash for the “Wired Control” setup. Press
the Mode I button on the Qflash that you want to be the Control Qflash.
15.4 Changing Remote 1 to Remote 2 or Remote 2 to Remote 1
Press the Mode I button on the Remote Qflash and use the Up J/Down
L button to change from Remote 1 to Remote2.
Note : If there is already a Remote 2 Qflash connected, it will automatical-
ly change to Remote 1
30
Download from Www.Somanuals.com. All Manuals Search And Download.
QFT5D INSTRUCTIONS 10/5/06 10:27 AM Page 35
16. TYPICAL LIGHTING SITUATIONS
This section covers some typical lighting situations that photographers find
themselves in. Here is how Qflash can help.
16.1 Portrait
Setting up a 3:1 portrait ratio (or any other ratio) has always been time
consuming. It is usually accomplished with three flashes: Main, Fill,
Background set to manual. Each flash needs to be adjusted and metered
separately. If the Main is in an umbrella or soft box this becomes even
more time consuming.
The Qflash ‘Wireless Control’ mode (with a FreeXWire) or ‘Wired Control’
mode (with a QF50 cable) provides a method for setting up portrait light-
ing which takes only a few moments. See Section 15 for details of the
Control Modes.
Set the Qflashes as shown in
the diagram to the right.
Place the camera at the Fill
Qflash position. The Main
Qflash can be placed in an
umbrella or soft box.
Once the Qflashes are
set up, make the fol-
lowing settings to the
Control Qflash:
Now the system is set up for perfect portrait lighting, with no metering
needed. The on-camera Qflash (Control) which is producing a flat light will
shut off one stop below the lens setting (Fill). Remote 1 Qflash will pro-
duce a light from the left (loop lighting) that is equal to the lens setting
(Main). This will achieve the portrait 3:1 ratio. The ratio can be adjusted
by changing the F number of the Control Qflash and the linked ratio.
For a ratio of 5:1 set the F number of the Control Qflash to 2 stops below
the lens setting, and set the Linked ratio to +2.
31
Download from Www.Somanuals.com. All Manuals Search And Download.
QFT5D INSTRUCTIONS 10/5/06 10:27 AM Page 36
16.2 Wireless lighting ratios made easy
When using multiple lights to light a subject it’s very easy to set up a light-
ing ratio between the
stops to +3 stops.
Equipment needed:
• One Qflash 5d-R
• One Qflash
(any version)
located to the right
of the subject
• Two FreeXWires
• Two QF30 cables
• Two Quantum
Turbo batteries
Set up:
• Connect the equipm
• Set the Main flash to
• Set the Fill flash, loc
position to Auto modl
F number set on the camera. Typically it is set to one stop under the
camera’s aperture, but can be as low as 2-1/2 stops under.
• Next Adjust the Linked ratio for the difference between Fill flash and the
camera’s aperture.
Example. If the camera is set for F8.0, and the Fill is set for F5.6, the Linked
ratio needs to be set to +1 ( the camera is one stop higher than the Fill)
16.3 Lighting ratios using a control cable
This set up is similar to the wire-
less one above, only Qflashes
are connected with QF50
cables instead of FreeXWires.
Equipment needed:
• One Qflash 5d-R located
at camera position
• One Qflash / 2/ 2d/4d/5d
located to the right of the
subject
• One QF50 control cable
• Two Quantum Turbo batteries
Set up: Same set up as above.
32
Download from Www.Somanuals.com. All Manuals Search And Download.
QFT5D INSTRUCTIONS 10/5/06 10:27 AM Page 37
11. CUSTOMER SERVICE
Having any trouble in using your Quantum product? We are here to help.
Mail, call, fax, or email our Service Department:
Service Department
Quantum Instruments
10 Commerce Drive
Hauppauge, NY 11788
Tel: (631) 656-7400
Fax: (631) 656-7410
Support, FAQ. If you suspect a malfunction or require adjustment, return
the unit to us with an accurate description of the problem. Please be sure
your problem is not caused by improper operating procedure or malfunc-
tions in your other equipment. Send all equipment carefully packaged and
insured to our address above.
An estimate of repair cost on out-of-warranty merchandise may be for-
warded if you desire. This will require that we contact you for approval
before proceeding and will delay return of your equipment. For fastest
repair time, you may pre-approve repairs up to a limit of $85 with your
credit card. We will bill you only for actual costs up to that limit. If repair
costs exceed your pre-approval, we will contact you.
Paying by check will delay the repair until the check clears (up to 15 days).
Payment by money order is acceptable.
Normal repair time is 10-15 days. For expedited service, contact our
Service Department.
Summary:
•
•
•
Ship via UPS, Parcel Post, or other carrier, insured.
Give a clear, detailed description of the problem.
Give your mailing address and daytime phone number, fax #,
and/or email.
For warranty repairs include a copy of the receipt.
•
In addition, for out-of-warranty repairs with pre-approval:
•
Provide your Visa, MasterCharge, or American Express card # and
expiration date.
•
•
Give us authority to charge repair costs up to $85.00.
Provide your billing address.
Note: Please do not e-mail your credit card information
LIMITED WARRANTY
Quantum products have a 1 year limited warranty. Please refer to the
Limited Warranty card for complete details, conditions, and terms.
33
Download from Www.Somanuals.com. All Manuals Search And Download.
QFT5D INSTRUCTIONS 10/5/06 10:27 AM Page 38
Qflash ACCESSORIES
QF63T / QF36X
REMOTE FLASH
HEAD
QFT2/X2
QFT2d/X2d
QFT4d/X4d
QFT5d/X5d
QF68 SOFTBOX
QF69 FOLDING SOFT BOX
& HOT SPOT REDUCER
34
Download from Www.Somanuals.com. All Manuals Search And Download.
QFT5D INSTRUCTIONS 10/5/06 10:27 AM Page 39
OTHER QUANTUM PRODUCTS
TURBO 2X2
TURBO COMPACT
QNEXUS
FW7Q
TURBO SC
FREE WIRE™
RADIO SLAVE
X
35
Download from Www.Somanuals.com. All Manuals Search And Download.
QFT5D INSTRUCTIONS 10/5/06 10:27 AM Page 40
Quantum Instruments, Inc
10 Commerce Drive, Hauppauge NY 11788-3968 USA
Tel: 1-631-656-7400
Fax: 1-631-656-7410
P635
Download from Www.Somanuals.com. All Manuals Search And Download.
|