NEW!
Cinema Loudspeaker System
SC-414
Features
• Four-way selectable, tri or quad- amplified screen channel system
• Unique HF/VHF diaphragm has less mass than traditional diaphragms
resulting in exceptional dynamic range, extended high frequency response
and lower distortion
• LF-4115 is constructed of MDF and is heavily braced
• Low-distortion waveguides provide highly articulate dialogue
• Shallow depth (20") facilitates installation
• THX™ approved for professional cinema applications
SC-414
Developed specifically for the unique requirements
of professional motion picture playback, the SC-414
extends QSC’s commitment to the cinema market.
As a member of the DCS Digital Cinema Speaker
Series, the SC-414 is a four-way, selectable tri or
quad-amplified screen channel loudspeaker system
comprised of two main units — the MHV-1090 mid-
high-very high-frequency system and the LF-4115
low-frequency system.
Specifications
Nominal Coverage
90° horizontal x +20 to -30° vertical
33 - 20 kHz
Frequency Range (-6 dB)
Active Crossover Frequencies
250, 1700 and 6000 Hz, 24 dB per octave
LF-4115
MH-1090
MF: 8Ω HF: 8Ω VHF: 8Ω
Impedance
4Ω
Sensitivity 1 watt/1 meter,
half space
93.5 dB
Tri-amp
Quad-amp
The MHV-1090 mid-high-very high system features
a high output, horn loaded 10" midrange cone
driver and a coaxial neodymium high-frequency/very
high-frequency compression driver. The MHV-1090
includes a driver protection network and a passive
crossover for tri-amp operation. The protection circuitry
prevents low-frequency signals from damaging the
high-frequency and very high-frequency driver. A
high power 10" cone driver allows operation as low
as 250 Hz and the advanced phase plug coupling
permits a crossover point of up to 1800 Hz to the
high-frequency horn. This ensures that most of the
dialog range is reproduced by a single element for
unmatched intelligibility.
MF:105 dB
HF/VHF: 110 dB
MF: 105 dB
HF: 110 dB
VHF: 110 dB
Maximum Input Power1
8 hours of 6 db crest factor
IEC 268 noise spectrum
400 W RMS
MF: 275 W RMS
MF: 275 W RMS
HF/VHF: 230 W RMS HF: 150 W RMS
VHF: 80 W RMS
2 hours of 6 db crest factor
pink noise, 50 Hz - 20 kHz,
AES method
500 W RMS
MF: 800 W RMS
HF/VHF: 500 W RMS maximum
Recommended
Amplifier Power
800 W RMS maximum
MF: 800 W RMS
HF: 500 W RMS
VHF: 300 W RMS maximum
The coaxial neodymium high-frequency/very high-
frequency compression driver provides a dramatic
improvement in dynamic response, clarity and
transparency. The annular high-frequency diaphragm
covers the frequency range between 1800 and
7000 Hz with a smooth, linear response. The large
diaphragm excursion of +/-0.8 mm results in high
output and increased power handling. The very high-
frequency driver covers the frequency range from
7,000 to 22,000 Hz and eliminates the dome break
up of conventional drivers that can cause resonance
and harsh, metallic sound.
Recommended Processing
Subsonic filter below 30 Hz,
>18 dB per octave
4th order LR crossover at 250, 1700 and
6000 Hz via QSC DCM or QSControl.net
Connectors
Transducers
Barrier strip screw terminals accept up to #10 AWG stranded wire
One 15" (381mm) high
efficiency, extended bass
woofer featuring a 4" copper
voice coil
MF: 10" high-effeciency, horn-loaded
cone with pahse plug
HF/VHF: coaxial neodymium compression
driver with 3.5" (90 mm) HF diaphram
and 1.75" (44 mm) VHF diaphram
Enclosure
Quasi B4 alignment, ported
enclosure with fully flared
ports, symmetrical port design,
tuned to 36 Hz, constructed
of MDF and heavily braced.
Features vandal resistant
woofer mounting bolts
Tilt/Pan Bracket
10° vertical tilt
10° horizontal pan
The LF-4115 single 15" (381mm) low-frequency
enclosure is designed specifically to address the
extended low-frequency response required for cinema
applications. The LF-4115 covers the frequency range
from 35 Hz to 250 Hz.
Dimensions (HWD)
18.5" x 30" x 20.3"
39" x 30" x 20"
(470 mm x 762 mm x 516 mm) (990 mm x 762 mm x 508 mm)
83 lbs (38 kg) 84 lbs (38.5 kg)
167 lbs (76.5 kg)
58.75" x 32"
The SC-414 is designed for ease of installation. The
MHV-1090 components come pre-assembled to
reduce field assembly time. Three bolts are all that are
required to secure the MHV-1090 to the top of the
LF-4115 enclosure.
Weight - Net
System Weight
Baffle Cut-Out
THX is a trademark of THX Ltd.
1) Maximum input power tested in accordance with IEC 268-5 recommendations, 50 Hz - 20 kHz band limiting, 6 dB signal crest factor.
Download from Www.Somanuals.com. All Manuals Search And Download.
|