SETTING DATE & TIME
PARTS
OPERATION
INTRODUCTION
To ensure that your camera records the proper
date and time on the files, you should run the
Setting Time Tools V2.0 program located in the
folder of the same name on the included mini-CD.
1. Operation Button
CHARGING
Thank you for your purchase of the Q-See QD113P
Portable Surveillance Device. This versatile tool is
built around an ultra-mini camera which combines
1.3-megapixel still photography and high-resolution
real-time video with audio in a compact, discrete
package. Store nearly 4,000 pictures or 2 hours of
video on the internal 4GB memory. View or save
your files on any PC with a USB port. Recharge the
pen with the included charger or from a computer’s
USB port. The ease of use, small size and el-
egant design make this a valuable tool for security
personnel, business people, students, tourists and
others.
The pen features a high-capacity rechargable
lithium polymer battery. This form of battery does
not have a “memory” effect meaning that it can
be recharged at any time without loss of capacity.
However, it is recommended that you fully charge
the battery and then use the camera normally until
it is fully discharged before recharging. Cycling the
battery in this manner for the first five times will
ensure maximum battery capacity and operation
time.
2. Status indicator light
3. Camera lens
When the program launches, a Command window
will open and the program will update the date and
time based on your computer’s settings.
4. Microphone
(behind pocket clip)
5. Reset button
6. USB plug
When charging the battery – whether using the
included charger, or plugged into an active USB
port – the status light will flash yellow/amber until
the battery is fully charged. During the first few
uses, allow the pen to continue charging for an
hour after the light stops flashing.
Depending upon your computer’s settings, you
may see a warning about the pen’s drive not
being available. The warning is normal as the
program re-mounts the pen. Click “Continue” and
the status of the update will be displayed in the
Command window. Keep clicking “Continue” until
you see the “Success” message in the window.
Your pen now is set to the proper date and time.
7. Mode Switch
Left = Video
Right = Still Image
When using the charger, both the green and red
lights will illuminate until the battery is fully charged.
When fully charged, only the red light will remain
illuminated.
8. Ball-point pen
STILL IMAGE CAPTURE
VIDEO RECORDING
PEN
HELPFUL HINTS
Rotate the metal collar at the tip to
extend or retract the writing nib.
1. Move the Mode Switch to the
left (use the pen’s tip if needed).
• When taking pictures, you will get the best
results if both you and your subject are relatively
still.
1. Move the Mode Switch to
the right (use the pen’s tip if
needed.)
2. Press the Operation Button for
1 second. The Status Indicator
light will briefly illuminate
amber before switching to blue
indicating that the camera is
recording.
• The camera should be at least one foot from
your subject when taking pictures.
2. Press the Operation Button for
1 second. The Status Indicator
light will briefly illuminate amber
before switching to the blue
“Ready” status.
USB DRIVE
The pen can be used as a standard USB Flash
memory stick for transporting and transferring files.
• While recording video, you should try to keep
the camera steady and avoid rapid movements
for best video quality.
3. Press the Operation Button
again to end the recording. The
INSUFFICIENT MEMORY OR BATTERY
3. Press once on the Operation
Button to take a picture. The
Status Indicator light will briefly
flash amber in addition to the
steady blue. The camera is
ready to take another picture.
• You should not hold the pocket clip while taking
video in order to avoid blocking the microphone
or lens.
When the camera’s memory is full or the battery
has run out of power, the Status Indicator light will
alternately flash amber and blue for five seconds.
It will then save the current file and shut down. You
must remove the files stored on the memory to
make space available to record further or recharge
the battery as appropriate.
Powering Up
Ready
Status Indicator light will switch
from blue to amber indicating
that the recording has been
saved and the camera is now on
“standby” and ready to record
more video.
Powering Up Recording
4. To turn off the camera, press
and hold the Operation Button
until the Status Indicator light
goes off. To conserve energy,
the camera will automatically
turn off after a few minutes of
inactivity as well.
4. To turn off the camera, press
and hold the Operation Button
until the Status Indicator light
goes off. To conserve energy,
the camera will automatically
turn off after a few minutes of
inactivity as well.
Standby
Recording Image
Download from Www.Somanuals.com. All Manuals Search And Download.
|