PYLE Audio TV Mount PSW101CM User Guide

Brick, Concrete and Stone wall:  
Using the wall mount as template to mark 6 holes location on the wall. Three holes are  
located at the top row of the slots and three more are located at the bottom row. The  
outer holes must be fall to the left and right of the two holes in the middle of the  
mount. Please make sure these holes are level and at least 6” between any two lines.  
Pre-drill these holes with a 10mm drill bit to at least 80mm deep hole. Insert wall  
anchors(P) into each of these holes. Attach the wall mount to the wall using 6 long  
bolts(O) and washers(Q).  
Tilt Flat Panel TV Bracket  
1
Multifunctional double deck wall mount  
INSTALLATION GUIDE  
Item No.:PSW101CM  
Q
O
Fig 2c  
Fig 2b  
Step 3: Hanging display  
Firstly lift the bracket mounted display over the wall mount. And then hook the  
brackets over the top of the wall mount. Rotate the display let the bottom of the  
brackets hook over the bottom of wall mount, as shown in Fig.3a. Then put safe  
bolts into the bottom of the brackets and lock it, as shown in Fig.3b.  
Warning: Some TV require two people to lift, as we are not responsible for any  
personal injury or product damage due to mishandling.  
Thank you for choosing our products  
Manufacturer: Logitek standard electronics  
cable manufacture co.,ltd.  
Knob  
4
Add: Science and Technology Zone, Jiangshan  
Town, Yinzhou District, Ningbo, China.  
Tel:86-574-88098888(88070226)  
Fax:86-574-88098788  
2,3  
Easy installing: Just hang up the display  
Safety: locking by spinning bolt on the bottom  
Max load capacity:75kg/165lbs  
1
Web: china-logitek.enalibaba.com  
TV size range: 36"~55"  
Adjustable angle: -5 15  
,
Fig 3a  
Fig 3b  
p.c.:315191  
-8-  
IMPORTANT: If don’t understand about right install ways, please  
consult to normal installing specialist.  
Download from Www.Somanuals.com. All Manuals Search And Download.  
3. For display with protruding HDTV tune or deeply  
curved backs(Fig b), two 9/16” spacers(R) or two  
½” spacers(S) should be used. Stack two spacers  
and then install them between display and the  
bracket. As shown in Fig 1c.  
WARNING  
Fig b  
We are not responsible for any personal injury or product damage due to mishandling,  
incorrect mounting, incorrect assembly or incorrect use of this product.  
Note: The supplied wall mounting hardware is not for use on steel stud walls or cold  
cinder block walls. If you are uncertain about the nature of your wall, please consult a  
qualified contractor. If the hardware you required is not included please contact your  
local hardware store .  
M4 Fig bit  
M5 Fig bit  
R
I
3
Caution:  
This Product LCD /Plasma Wall Mount Bracket is intended for use only  
R
N
N
2
with the maximum weights indicated .See apparatus instructions .Use with products  
heavier than the maximum weights indicated may result in instability causing possible  
injury .  
J
Step 1: Attach bracket to TV  
Check your TV manual to confirm the diameter of bolt to be used or choose an  
appropriate bolt according to size, height and position of the holes on your TV. See  
pages 4-6 of these instructions for examples.  
For correct installing, make sure that hook of every bracket must facing down. Use  
selected bolts, spacers and washers for installing bracket at the back of display.  
Adjust two brackets to equal heights and level. Once aligned, tightly secure the  
bolts.  
S
R
3
N
N
K
L
2
M8 Fig bit  
IMPORTANT: Don't force the bolt into the hole, which will cause a damage of  
equipments and injure of person. Don't use electric drill to fasten any bolts.  
M6 Fig bit  
Fig 1c  
-3-  
-6-  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Following examples shows how to use bolts, spacers and square washers.  
2. Some displays have curved backs with  
recessed mounting lands(Fig.a). It will  
require the use of spacer. For this display,  
install a 9/16” spacer(R) or ½”spacer(S)  
between display and the bracket. As  
shown in Fig 1b.  
1.Some displays have vertical backs. No spacer is required. Install the bracket directly  
to the back of display by using bolts and square washers provided. As shown in Fig.1a.  
Fig a  
M4 Fig bit  
M5 Fig bit  
M4 Fig bit  
M5 Fig bit  
R
R
N
A
E
2
3
N
3
N
2
F
N
B
3
S
R
2
N
N
D
G
N
C,M  
N
H
3
2
M6,1/4-20 5/8Fig bit  
M8 Fig bit  
M6 Fig bit  
M8 Fig bit  
Fig 1a  
Fig 1b  
-5-  
-4-  
Download from Www.Somanuals.com. All Manuals Search And Download.  

QSC Audio Speaker System Network Audio Systems User Guide
Remington Hair Dryer D 3310 User Guide
Renesas Stereo System R8C 25 User Guide
ResMed Nebulizer Pixi User Guide
Rival Fryer S12 GN User Guide
Rockford Fosgate Car Stereo System RFX9220M User Guide
Roland Baby Monitor MKS 10 User Guide
Ryobi Drill HP1830M User Guide
Sanyo Projector PLV Z4 User Guide
Scion Automobile Accessories 128 7907A User Guide