Model No. PFTL94105.1
Serial No.
USER'S MANUAL
Write the serial number in the space
above for future reference.
Serial Number
Decal
QUESTIONS?
As a manufacturer, we are com-
mitted to providing complete
customer satisfaction. If you
have questions, or if parts are
damaged or missing, PLEASE
CONTACT OUR CUSTOMER
SERVICE DEPARTMENT
DIRECTLY.
CALL TOLL-FREE:
1-888-533-1333
Mon.–Fri., 6 a.m.–6 p.m. MST
ON THE WEB:
CAUTION
Read all precautions and instruc-
tions in this manual before using
this equipment. Save this man-
ual for future reference.
Visit our website at
new products, prizes,
fitness tips, and much more!
Download from Www.Somanuals.com. All Manuals Search And Download.
IMPORTANT PRECAUTIONS
WARNING:
To reduce the risk of burns, fire, electric shock, or injury to persons, read the
following important precautions and information before operating the treadmill.
1. It is the responsibility of the owner to ensure
that all users of this treadmill are adequately
informed of all warnings and precautions.
11. Failure to use a properly functioning surge
suppressor could result in damage to the con-
trol system of the treadmill. If the control sys-
tem is damaged, the walking belt may change
speed, accelerate, or stop unexpectedly,
which may result in a fall and serious injury.
2. Use the treadmill only as described in this
manual.
3. Place the treadmill on a level surface, with at
least eight feet of clearance behind it and two
feet on each side. Do not place the treadmill
on any surface that blocks air openings. To
protect the floor or carpet from damage, place
a mat under the treadmill.
12. Keep the power cord and the surge suppres-
sor away from heated surfaces.
13. Never move the walking belt while the power
is turned off. Do not operate the treadmill if
the power cord or plug is damaged, or if the
treadmill is not working properly. (See
BEFORE YOU BEGIN on page 6 if the tread-
mill is not working properly.)
4. Keep the treadmill indoors, away from mois-
ture and dust. Do not put the treadmill in a
garage or covered patio, or near water.
14. Read, understand, and test the emergency
stop procedure before using the treadmill (see
TREADMILL OPERATION on page 10).
5. Do not operate the treadmill where aerosol
products are used or oxygen is administered.
6. Keep children under the age of 12 and pets
away from the treadmill at all times.
15. Never start the treadmill while you are stand-
ing on the walking belt. Always hold the
handrails while using the treadmill.
7. The treadmill should not be used by persons
weighing more than 350 pounds. Never allow
more than one person on the treadmill at a time.
16. To protect the treadmill and TV during light-
ning storms, unplug the power cord from the
wall outlet and disconnect the cable system.
This will prevent damage due to lightning and
power line surges.
8. Wear appropriate exercise clothes when
using the treadmill. Do not wear loose clothes
that could become caught in the treadmill.
Athletic support clothes are recommended
for both men and women. Always wear ath-
letic shoes. Never use the treadmill with bare
feet, wearing only stockings, or in sandals.
17. The treadmill is capable of high speeds.
Adjust the speed in small increments to avoid
sudden jumps in speed.
18. The pulse sensor is not a medical device.
Various factors, including the user's move-
ment, may affect the accuracy of heart rate
readings. The pulse sensor is intended only
as an exercise aid in determining heart rate
trends in general.
9. When connecting the power cord (see page 10),
plug the power cord into a surge suppressor
(not included) and plug the surge suppressor
into a grounded circuit capable of carrying 15
or more amps. No other appliance should be on
the same circuit. Do not use an extension cord.
19. Never leave the treadmill unattended while it
is running. Always remove the key, unplug
the power cord, and move the reset/off circuit
breaker to the “off” position when the tread-
mill is not in use. (See the drawing on page 6
for the location of the circuit breaker.)
10. Use only a single-outlet surge suppressor
that meets all of the specifications described
on page 10. To purchase a surge suppressor,
see your local PROFORM dealer or call the
toll-free telephone number on the front cover
of this manual and order part number 146148,
or see your local electronics store.
3
Download from Www.Somanuals.com. All Manuals Search And Download.
20. Do not attempt to raise, lower, or move the
treadmill until it is properly assembled. (See
ASSEMBLY on page 7, and HOW TO FOLD
AND MOVE THE TREADMILL on page 22.)
You must be able to safely lift 45 pounds (20
kg) to raise, lower, or move the treadmill.
25. The treadmill is intended for in-home use
only. Do not use the treadmill in any
commercial, rental, or institutional setting.
26. To reduce the risk of electric shock, do not
remove the cover or the back of the televi-
sion. There are no user serviceable parts in-
side. Refer servicing to qualified service per-
sonnel.
21. When folding or moving the treadmill, make
sure that the storage latch is fully closed.
27. Upon completion of any service or repairs to
the treadmill or the television, ask the service
technician to perform safety checks to con-
firm that the unit is in proper operating con-
dition.
22. Inspect and properly tighten all parts of the
treadmill every three months.
23. Never drop or insert any object into any open-
ing.
Note to CATV system installer: This reminder
is provided to call the CATV system in-
staller’s attention to Article 820-40 of the NEC
that provides guidelines for proper grounding
and, in particular, specifies that the cable
ground shall be connected to the grounding
system of the building, as close to the point
of cable entry as practical.
24.
DANGER:
Always unplug the power
cord immediately after use, before cleaning
the treadmill, and before performing the main-
tenance and adjustment procedures de-
scribed in this manual. Never remove the
motor hood unless instructed to do so by an
authorized service representative. Servicing
other than the procedures in this manual
should be performed by an authorized service
representative only.
4
Download from Www.Somanuals.com. All Manuals Search And Download.
Power Lines
Service
Entrance
Conductors
75 ohm Terminal
Service
Entrance
Equipment
Power Service Grounding
Electrode System (e.g.
Interior Metal Water Pipe)
Ground
Clamps
WARNING:
Before beginning this or any exercise program, consult your physician. This
is especially important for persons over the age of 35 or persons with pre-existing health problems.
Read all instructions before using. ICON assumes no responsibility for personal injury or property
damage sustained by or through the use of this product.
SAVE THESE INSTRUCTIONS
The decals shown here have been applied in the indicated locations. If a decal is miss-
ing, or if it is not legible, call the telephone number on the front cover of this man-
ual and request a free replacement decal. Apply the decal in the location shown.
Note: The decals are not shown at actual size.
5
Download from Www.Somanuals.com. All Manuals Search And Download.
BEFORE YOU BEGIN
Congratulations for purchasing the PROFORM® PRO
SERIES 1500 treadmill. The PRO SERIES 1500 tread-
mill offers an impressive array of features designed to
help you achieve your fitness goals in the convenience
of your home. From the advanced console to the cush-
ioned walking platform, the PRO SERIES 1500 tread-
mill is designed to make each workout more effective
and enjoyable. And when you’re not exercising, the
treadmill can be folded away, taking less than half the
floor space of conventional treadmills.
reading this manual, please see the front cover of this
manual. To help us assist you, note the product model
number and serial number before contacting us. The
model number and the location of the serial number
decal are shown on the front cover of this manual.
To avoid a registration fee for any service needed
under warranty, you must register the treadmill at
Before reading further, please review the drawing
below and familiarize yourself with the labeled parts.
For your benefit, read this manual carefully before
you use the treadmill. If you have questions after
Personal Television
Accessory Tray
Fan
Console
Key/Clip
Handrail
Handgrip Pulse Sensor
Reset/Off
Circuit Breaker
Walking Belt
Foot Rail
Power Cord
Adjustable Cushioned
Walking Platform (see page 20)
RIGHT SIDE
Rear Roller
Adjustment Bolts
6
Download from Www.Somanuals.com. All Manuals Search And Download.
ASSEMBLY
To hire an authorized service technician to assemble the treadmill, call toll-free 1-800-445-2480. Assembly
requires two persons. Place the treadmill in a cleared area and remove all packing materials. Do not dispose of
the packing materials until the treadmill is assembled.
Note: The underside of the treadmill walking belt is coated with high-performance lubricant. During shipping, a
small amount of lubricant may be transferred to the top of the walking belt, the sides of the walking platform, or
the shipping carton. This does not affect treadmill performance. If there is lubricant on top of the walking belt or
on the sides of the walking platform, wipe off the lubricant with a soft cloth and a mild, non-abrasive cleaner.
Assembly requires a phillips screwdriver
and the included allen wrench
.
1. With the help of a second person, carefully raise the
Uprights (65) to a vertical position.
1
Console
Assembly
Have the second person hold the console assembly near
the Uprights (65) as shown. Look under the console as-
sembly and locate the Console Wire Harness (71) and the
TV cable.
Cut the plastic ties securing the Upright Wire Harness
(85) and the Upright TV Cable (100) to the Uprights (65).
Connect the Upright TV Cable to the TV cable in the con-
sole assembly. Connect the Upright Wire Harness to the
Console Wire Harness (71). Make sure to connect the
connectors properly (see the inset drawing). The con-
nectors should slide together easily and snap into
place. If the connectors do not slide together easily and
snap into place, turn one connector and try again. IF THE
CONNECTORS ARE NOT CONNECTED PROPERLY,
THE CONSOLE MAY BE DAMAGED WHEN THE
POWER IS TURNED ON.
TV Cable
85
71
100
65
65
71
85
2. Insert the slack in the Wire Harnesses (71, 85) and the
TV cable into the Uprights (65).
2
Console
Assembly
Set the console assembly on the Uprights (65). While a
second person holds the console assembly, attach the
console assembly with four 1” Console Bolts (133) and
four Console Washers (69) as shown. Firmly tighten the
Console Bolts.
71, 85
69
133
69
133
65
65
69
133
7
Download from Www.Somanuals.com. All Manuals Search And Download.
3. With the help of a second person, raise the treadmill
Frame (55). Hold the Latch Housing (68) and the Latch
Housing Cover (5) against the sides of the Frame as
shown. Loosely thread the two blunt-tipped 1/2” Screws
(132) into the Latch Housing Cover and the Latch Housing
as shown. Do not tighten the Screws yet.
3
Hole
Knob
132
Remove the knob from the pin. Make sure that the collar
and the spring are on the pin. The collar should be on the
side of the spring shown. Insert the pin into the Latch
Housing (68), and tighten the knob back onto it.
140
114
5
68
Small
Holes
Align the pin with the hole in the Left Handgrip (140) by
sliding the Latch Housing (68) up or down. Make sure that
the pin can be inserted fully into the hole. Hold the Latch
Housing in place as you tighten two 1/2” Tek Screws (114)
into the Latch Housing and the Frame (55). Then, tighten
the 1/2” Screws (132). Note: It may be necessary to pull
on the knob to access and tighten the Screws.
Collar
55
Spring
Pin
132
114
4. Note the location of the 75 ohm terminal on the treadmill.
For the television to operate properly, a 75 ohm CATV
cable must be connected to the 75 ohm terminal (see page
9).
4
75 Ohm
Terminal
5. Make sure that all parts are properly tightened before you use the treadmill. Place a mat beneath the
treadmill to protect the floor or carpet. Note: Extra hardware may be included. Keep the included allen
wrench in a secure place; the allen wrench is used to adjust the walking belt (see page 23). For your benefit,
we recommend that you familiarize yourself with the TROUBLESHOOTING section on pages 23 and 24.
8
Download from Www.Somanuals.com. All Manuals Search And Download.
Before operating the television, you must connect a 75 ohm CATV cable to the 75 ohm terminal on the
treadmill. Note: Use a CATV cable to connect to an external source such as a cable box, analog cable, satellite
TV box, or VCR. No CATV cable is included.
HOW TO CONNECT A 75 OHM CATV CABLE
HOW TO CONNECT AN EXTERNAL SOURCE
USING A CATV CABLE
1. Connect a 75 ohm
CATV cable to the 75
ohm terminal near the
power cord.
1. Connect one end of a 75 ohm CATV cable to the 75
ohm output jack on your external source.
75 Ohm CATV Cable
75 Ohm Terminal
2. Plug in the power cord of your external source. See
your external source’s user’s manual for proper
grounding instructions.
3. Connect the 75 ohm CATV cable to the 75 ohm ter-
minal near the power cord.
9
Download from Www.Somanuals.com. All Manuals Search And Download.
TREADMILL OPERATION
THE PRE-LUBRICATED WALKING BELT
tric shock. This product is equipped with a cord having
an equipment-grounding conductor and a grounding
plug. Plug the power cord into a surge suppressor,
and plug the surge suppressor into an appropriate
outlet that is properly installed and grounded in
accordance with all local codes and ordinances.
Important: The treadmill is not compatible with
GFCI-equipped outlets.
Your treadmill features a walking belt coated with high-
performance lubricant. IMPORTANT: Never apply sil-
icone spray or other substances to the walking
belt or the walking platform. Such substances will
deteriorate the walking belt and cause excessive
wear.
HOW TO PLUG IN THE POWER CORD
This product is for use on a nominal 120-volt circuit,
and has a grounding plug that looks like the plug illus-
trated in drawing 1 below. A temporary adapter that
looks like the adapter illustrated in drawing 2 may be
used to connect the surge suppressor to a 2-pole
receptacle as shown in drawing 2 if a properly
grounded outlet is not available.
DANGER:
Improper connection
of the equipment-grounding conductor can
result in an increased risk of electric shock.
Check with a qualified electrician or service-
man if you are in doubt as to whether the
product is properly grounded. Do not modify
the plug provided with the product—if it will
not fit the outlet, have a proper outlet
1
Grounded Outlet Box
Surge Suppressor
Grounding Pin
installed by a qualified electrician.
Your treadmill, like any other type of sophisticated
electronic equipment, can be seriously damaged by
sudden voltage changes in your home’s power.
Voltage surges, spikes, and noise interference can
result from weather conditions or from other appliances
being turned on or off. To decrease the possibility of
your treadmill being damaged, always use a surge
suppressor with your treadmill (see drawing 1 at
the right). To purchase a surge suppressor, see
your local PROFORM dealer or call the toll-free
telephone number on the front cover of this man-
ual and order part number 146148, or see your local
electronics store.
Grounding Pin
Grounded Outlet
Grounding Plug
2
Grounded Outlet Box
Adapter
Surge Suppressor
Use only a single-outlet surge suppressor that is
UL 1449 listed as a transient voltage surge sup-
pressor (TVSS). The surge suppressor must have a
UL suppressed voltage rating of 400 volts or less
and a minimum surge dissipation of 450 joules.
The surge suppressor must be electrically rated for
120 volts AC and 15 amps. There must be a moni-
toring light on the surge suppressor to indicate
whether it is functioning properly. Failure to use a
properly functioning surge suppressor could result
in damage to the control system of the treadmill. If
the control system is damaged, the walking belt
may change speed, accelerate or stop unexpect-
edly, which may result in a fall and serious injury.
Lug
Metal Screw
The temporary adapter should be used only until a
properly grounded outlet (drawing 1) can be installed
by a qualified electrician.
The green-colored rigid ear, lug, or the like extending
from the adapter must be connected to a permanent
ground such as a properly grounded outlet box cover.
Whenever the adapter is used it must be held in place
by a metal screw. Some 2-pole receptacle outlet box
covers are not grounded. Contact a qualified elec-
trician to determine if the outlet box cover is
grounded before using an adapter.
This product must be grounded. If it should malfunc-
tion or break down, grounding provides a path of least
resistance for electric current to reduce the risk of elec-
10
Download from Www.Somanuals.com. All Manuals Search And Download.
Key
Clip
FEATURES OF THE CONSOLE
treadmill to keep your heart rate near target heart rate
settings while you exercise.
The treadmill console offers an impressive array of
features designed to help you get the most from your
workouts.
Whether you select the manual mode or a program,
you can enjoy the shows of your choice on the per-
sonal television while you get in shape.
When the manual mode of the console is selected, the
speed and incline of the treadmill can be changed with
the touch of a button. As you exercise, the console
will display continuous exercise feedback. You can
even measure your heart rate using the handgrip pulse
sensor.
To use the manual mode of the console, follow the
steps beginning on page 12. To use a preset program,
see page 14. To create and use a custom program,
see pages 16 and 17. To use a heart rate program,
see page 18. To operate the personal television, see
page 20.
In addition, the console offers ten preset programs.
Each program automatically controls the speed and in-
cline of the treadmill as it guides you through an effec-
tive workout. You can even create custom workout pro-
grams and store them in memory for future use.
Note: If there is a sheet of clear plastic on the face of
the console, peel off the plastic. To prevent damage to
the walking platform, wear clean athletic shoes while
using the treadmill. The first time the treadmill is used,
observe the alignment of the walking belt, and center
the walking belt if necessary (see page 24).
Four heart rate programs are also offered. Each pro-
gram automatically adjusts the speed and incline of the
11
Download from Www.Somanuals.com. All Manuals Search And Download.
mph; if a button is held down, the speed setting
will change in increments of 0.5 mph. Note: After
the buttons are pressed, it may take a moment for
the walking belt to reach the selected speed setting.
HOW TO TURN ON THE POWER
IMPORTANT: If the treadmill has been exposed to
cold temperatures, allow it to warm to room tem-
perature before turning on the power. If you do not
do this, the console displays or other electrical
components may become damaged.
If one of the numbered Speed buttons is pressed,
the walking belt will gradually increase in speed
until it reaches the selected speed setting.
Plug in the power cord
(see page 10). Next, locate
To stop the walking belt, press the Stop button.
The time will begin to flash in the left display. To
restart the walking belt, press the Start button, the
Speed increase button, or one of the numbered
Speed buttons.
the reset/off circuit breaker
near the power cord. Make
sure that the circuit
breaker is in the reset po-
sition.
Reset
Position
Change the incline of the treadmill as desired.
4
5
Stand on the foot rails of the treadmill. Find the clip at-
tached to the key (see the drawing on page 11) and at-
tach the clip securely to the waistband of your clothes.
Next, insert the key into the console. After a moment,
the displays will light, and after a few seconds, the
television will turn on. Important: In an emergency
situation, the key can be pulled from the console,
causing the walking belt to slow to a stop. Test the
clip by carefully taking a few steps backward until
the key is pulled from the console. If the key is not
pulled from the console, adjust the position of the
clip as needed.
To change the incline of the treadmill, press the
Incline buttons. Each time a button is pressed, the
incline will change by 0.5%. To change the incline
setting quickly, press the numbered Incline buttons.
Note: After the buttons are pressed, it may take a
moment for the treadmill to reach the selected in-
cline setting.
Follow your progress with the two displays.
The left display—This display will show the
elapsed time, your pace (in minutes per mile), and
the incline level of the treadmill. Note: When a pro-
gram is selected, this display will show the time
remaining in the program instead of the elapsed
time. Each time the incline of the treadmill
changes, the display will show the incline setting
for several seconds.
HOW TO USE THE MANUAL MODE
Insert the key into the console.
1
See HOW TO TURN ON THE POWER above.
Training Zone Bar Track
Select the manual mode.
2
When the key is inserted, the manual mode will be
selected. If you have selected a program, press
the Manual button to reselect the manual mode.
Start the walking belt.
3
The left display will also show a workout intensity
bar that indicates the relative intensity of your exer-
cise.
To start the walking belt, press the Start button,
the Speed increase button, or one of the twelve
numbered Speed buttons.
When the manual mode is selected, the left display
will also show a track. As you exercise, the indica-
tors around the track will appear in succession
until the entire track is lit. The track will then dis-
appear the indicators will again begin to appear in
succession.
If the Start button or the Speed increase button is
pressed, the walking belt will begin to move at 1
mph. As you exercise, change the speed of the
walking belt as desired by pressing the Speed in-
crease and decrease buttons. Each time a button
is pressed, the speed setting will change by 0.1
12
Download from Www.Somanuals.com. All Manuals Search And Download.
The right display—This display will show the dis-
tance that you have walked or run, the number of
1/4-mile laps you have completed, the speed of
the walking belt, and the approximate numbers of
calories and fat calories you have burned (see
FAT BURNING on page 25).
make sure that your hands are clean. Next, hold
the handgrip pulse sensor with your palms resting
on the metal contacts; avoid moving your hands.
When your pulse is detected, the heart-shaped in-
dicator in the right display will flash each time your
heart beats, one or two dashes (– –) will appear,
and then your heart rate will be shown. For the
most accurate heart rate reading, continue to
hold the contacts for about 15 seconds.
Note: The handgrip pulse sensor is intended to be
used only for heart rate measurement. Do not
use the handgrip pulse sensor as a handlebar.
Always hold the handrails for support when
you are not measuring your heart rate.
The right display will also show your heart rate
when you use the handgrip pulse sensor. In addi-
tion, during heart rate programs the right display
will show a heart rate bar that shows your heart
rate as a percentage of your age-predicted maxi-
mum heart rate (see step 3 on page 18 for an ex-
planation of your age-predicted maximum heart
rate). For example, if four to six segments of the
bar appear, your heart rate is between 60% and
70% of your age-predicted maximum heart rate.
Turn on the fan if desired.
7
8
To turn on the fan, press the button below the fan.
To turn on the fan at high speed, press the button
a second time. To turn off the fan, press the but-
ton a third time. Note: If the fan is on when the
walking belt is stopped, the fan will automatically
turn off after a few minutes.
When you are finished exercising, remove the
key from the console.
Heart Rate Bar
Step onto the foot rails, press the Stop button, and
adjust the incline of the treadmill to the lowest
setting. The incline must be at the lowest setting
when the treadmill is folded to the storage posi-
tion or the treadmill will become damaged. Next,
remove the key from the console and put it in a se-
cure place. Note: If the displays remain lit after
the key is removed, the console is in the
“demo” mode. See HOW TO USE THE INFOR-
MATION MODE on page 20 and turn off the
demo mode.
Note: The console can display speed and dis-
tance in either miles or kilometers. The letters
“MPH” or “Km/H” will appear in the right display to
show which unit of measurement is selected. To
change the unit of measurement, see HOW TO
USE THE INFORMATION MODE on page 20. For
simplicity, all instructions in this section refer
to miles.
When you are finished using the treadmill, switch
the reset/off circuit breaker to the “off” position and
unplug the power cord. IMPORTANT: If you do
not do this, the treadmill’s electrical compo-
nents may wear prematurely.
To reset the displays, press the Stop button, re-
move the key, and then reinsert the key.
Measure your heart rate if desired.
6
Before using
the handgrip
pulse sensor,
remove the
sheets of clear
plastic from the
metal contacts.
In addition,
Contacts
13
Download from Www.Somanuals.com. All Manuals Search And Download.
The speed setting for the
first segment will be
HOW TO USE A PRESET PROGRAM
Current Segment
Column
shown in the flashing
Current Segment column
of the matrix. (The in-
cline settings are not
shown in the matrix.)
The speed settings for
the next seven segments
Insert the key into the console.
1
See HOW TO TURN ON THE POWER on
page 12.
Select a preset program.
2
will be shown in the columns at the right.
To select a preset program, press the Speed &
Incline button repeatedly. The right display will
show which preset program (P-1 through P-10) is
selected.
When only three seconds remain in the first seg-
ment of the program, both the Current Segment
column and the column to the right will flash, and
a series of tones will sound. If the speed and/or in-
cline of the treadmill is about to change, the left
display and/or the right display will flash to alert
you. When the first segment ends, all speed set-
tings in the matrix will move one column to the
left. The speed setting for the second segment will
then be shown in the flashing Current Segment
column, and the treadmill will automatically adjust
to the speed and incline settings for the second
segment. Note: If all of the indicators in the
Current Segment column are lit after the speed
settings have moved to the left, the speed settings
may move downward so that only the highest indi-
cators appear in the matrix. If some indicators in
the Current Segment column are not lit when the
speed settings move to the left again, the speed
settings will move back up.
When a preset program is selected, the left dis-
play will flash the maximum incline setting of the
program for a few seconds, and the right display
will flash the maximum speed setting. The left dis-
play will then show how long the program will last.
In addition, the first ten speed settings of the pro-
gram will appear the matrix in the left display.
The program will continue in this way until the
speed setting for the last segment is shown in the
Current Segment column and the last segment
ends. The walking belt will then slow to a stop.
Matrix
If the speed or incline setting is too high or too low
at any time during the program, you can manually
override the setting by pressing the Speed or
Incline buttons. Every few times a Speed button is
pressed, an additional indicator will appear or dis-
appear in the Current Segment column. (If any of
the columns to the right of the Current Segment
column have the same number of indicators as the
Current Segment column, an additional indicator
may appear or disappear in those columns as
well.) Note: When the next segment of the pro-
gram begins, the treadmill will automatically
adjust to the speed and incline settings for the
next segment.
Press the Start button or the Speed increase
button to start the program.
3
A moment after the button is pressed, the tread-
mill will automatically adjust to the first speed and
incline settings of the program. Hold the handrails
and begin walking.
Each program is divided into several one-minute
segments. One speed setting and one incline set-
ting are programmed for each segment. Note: The
same speed setting and/or incline setting may be
programmed for two or more consecutive seg-
ments.
14
Download from Www.Somanuals.com. All Manuals Search And Download.
To stop the program at any time, press the Stop
button. The time will begin to flash in the left dis-
play. To restart the program, press the Start button
or the Speed increase button. The walking belt will
begin to move at 1 mph. When the next segment
of the program begins, the treadmill will automati-
cally adjust to the speed and incline settings for the
next segment.
Turn on the fan if desired.
6
7
See step 7 on page 13.
When you are finished exercising, remove the
key from the console.
When the program ends, make sure that the in-
cline of the treadmill is at the lowest setting.
Next, remove the key from the console and put it in
a secure place. Note: If the displays and various
indicators remain lit after the key is removed,
the console is in the “demo” mode. See HOW
TO USE THE INFORMATION MODE on page 20
and turn off the demo mode.
Follow your progress with the displays.
See step 5 on page 12.
4
5
Measure your heart rate if desired.
See step 6 on page 13.
When you are finished using the treadmill,
switch the reset/off circuit breaker to the “off”
position and unplug the power cord.
15
Download from Www.Somanuals.com. All Manuals Search And Download.
See the matrix in the left
display. Each custom
program is divided into
one-minute segments.
One speed setting and
one incline setting can
be programmed for each
segment. The speed set-
ting for the first segment
will be shown in the flashing Current Segment col-
umn of the matrix. (The incline settings are not
shown in the matrix.) To program a speed setting
and an incline setting for the first segment, simply
adjust the speed and incline of the treadmill as de-
sired by pressing the Speed and Incline buttons.
Every few times a Speed button is pressed, an
additional indicator will appear or disappear in the
Current Segment column.
HOW TO CREATE A CUSTOM PROGRAM
Current Segment
Column
Insert the key into the console.
1
See HOW TO TURN ON THE POWER on
page 12.
Select a custom program.
2
To select a custom program, press the Custom
button repeatedly until “P-15” or “P-16” appears in
the right display.
When the first segment of the program ends, the
current speed setting and the current incline set-
ting will be stored in memory. The three columns
of indicators will then move one column to the left,
and the speed setting for the second segment will
be shown in the flashing Current Segment column.
Program a speed setting and an incline setting for
the second segment as described above.
If the custom program has not yet been defined,
three columns of indicators will appear in the ma-
trix in the left display. If more than three
columns of indicators appear, see HOW TO
USE A CUSTOM PROGRAM on page 17.
Continue programming speed and incline settings
for as many segments as desired; custom pro-
grams can have up to forty segments. When you
are finished with your workout, press the Stop but-
ton twice. The speed and incline settings that you
have programmed and the number of segments
that you have programmed will then be saved in
memory.
Matrix
Press the Start button or the Speed increase
button and program the desired speed and in-
cline settings.
When you are finished exercising, remove the
key from the console.
3
4
See step 7 on page 15.
A moment after the button is pressed, the walking
belt will begin to move. Hold the handrails and
begin walking.
16
Download from Www.Somanuals.com. All Manuals Search And Download.
ries of tones will sound, the speed setting and the
incline setting will flash in the displays, and all
speed settings will move one column to the left.
The speed setting for the second segment will then
be shown in the flashing Current Segment column
and the treadmill will automatically adjust to the
second speed and incline settings that you pro-
grammed previously.
HOW TO USE A CUSTOM PROGRAM
Insert the key into the console.
1
See HOW TO TURN ON THE POWER on
page 12.
Select a custom program.
2
The program will continue until the speed setting
for the last segment is shown in the Current
Segment column and the last segment ends. The
walking belt will then slow to a stop.
To select a custom program, press the Custom
button repeatedly until “P-15” or “P-16” appears in
the right display.
When a custom program is selected, the left dis-
play will flash the maximum incline setting of the
program for a few seconds, and the right display
will flash the maximum speed setting. The left dis-
play will then show how long the program will last.
In addition, the first ten speed settings of the pro-
gram will appear in the matrix in the left display.
Note: If only three columns of indicators ap-
pear, see HOW TO CREATE A CUSTOM PRO-
GRAM on page 16.
If desired, you can redefine the program while
using it. To change the speed or incline setting
during the current segment, simply press the
Speed or Incline buttons. When the current segment
ends, the new setting will be saved in memory. To
increase the length of the program, first wait until
the program ends. Then, press the Start button, and
program speed and incline settings for as many ad-
ditional segments as desired. When you have
added as many segments as desired, press the
Stop button twice. To decrease the length of the
program, press the Stop button twice at any time
before the program ends.
Press the Start button or the Speed increase
button to start the program.
3
To stop the program at any time, press the Stop
button. The time will begin to flash in the left dis-
play. To restart the program, press the Start but-
ton or the Speed increase button.
A moment after the button is pressed, the tread-
mill will automatically adjust to the first speed and
incline settings that you programmed previously.
Hold the handrails and begin walking.
Each program is divided into several one-minute
segments. One speed setting and one incline set-
ting are programmed for each segment. The
speed setting for the first segment will be shown in
the flashing Current
Follow your progress with the displays.
See step 5 on page 12.
4
5
6
7
Measure your heart rate if desired.
See step 6 on page 13.
Segment column of the
Current Segment
matrix. (The incline set-
Column
tings are not shown in
the matrix.) The speed
settings for the next
several segments will
be shown in the
Turn on the fan if desired.
See step 7 on page 13.
columns to the right.
When you are finished exercising, remove the
key from the console.
When only three seconds remain in the first seg-
ment of the program, both the Current Segment
column and the column to the right will flash, a se-
See step 7 on page 15.
17
Download from Www.Somanuals.com. All Manuals Search And Download.
Enter your age.
HOW TO USE A HEART RATE PROGRAM
3
When a heart rate program is selected, the word
“AGE” and the current age setting will begin to
flash in the right display. If you have already en-
tered your age, press the Enter button. If you have
not entered your age, press the + or – button be-
side the Enter button to enter your age, and then
press the Enter button.
CAUTION:
If you have heart prob-
lems, or if you are over 60 years of age and
have been inactive, do not use the heart rate
programs. If you are taking medication regu-
larly, consult your physician to find whether
the medication will affect your exercise heart
rate.
Follow the steps below to use a heart rate program.
Insert the key into the console.
1
See HOW TO TURN ON THE POWER on
page 12.
Enter a target heart rate setting for the program.
4
If heart rate program 11 is selected, the letters
“PLS” and the target heart rate setting for the pro-
gram will begin to flash in the right display. If de-
sired, change the target heart rate setting by
pressing the + or – button beside the Enter button
(see EXERCISE INTENSITY on page 25). Then,
press the Enter button.
Select a heart rate program.
2
To select a heart rate program, press the Heart
Rate button repeatedly until “P-11,” “P-12,” “P-13,”
or “P-14” appears in the right display.
If heart rate program 11 is selected, a pulse
symbol will scroll across the matrix in the left dis-
play. If heart rate program 12, 13, or 14 is se-
lected, a profile of the target heart rate settings of
the program will appear in the matrix in the left
display.
If heart rate program 12, 13, or 14 is selected,
the letters “PLS” and the maximum target heart
rate setting for the program will begin to flash in
the right display. If desired, change the maximum
target heart rate setting by pressing the + or – but-
ton beside the Enter button (see EXERCISE IN-
TENSITY on page 25). Then, press the Enter but-
ton. Note: If the maximum target heart rate setting
is changed, the intensity level of the entire pro-
gram will change.
Note: During heart rate program 11, your heart
rate will remain near a target heart rate setting
that you select. During heart rate programs 12,
13, or 14, your heart rate will reach approximately
85% of your age-predicted maximum heart rate.
Note: Your maximum heart rate is estimated by
subtracting your age from 220. For example, if
you are 30 years old, your age-predicted maxi-
mum heart rate is 190 beats per minute (220 – 30
= 190).
18
Download from Www.Somanuals.com. All Manuals Search And Download.
Hold the handgrip pulse sensor.
During all heart rate programs, the console will
regularly compare your heart rate to the target
heart rate setting for the current segment. If your
heart rate is too far below or above the target
heart rate setting, the speed of the walking belt
will automatically increase or decrease to bring
your heart rate closer to the target heart rate set-
ting.
5
6
It is not necessary to hold the handgrip pulse sen-
sor continuously during a pulse program; how-
ever, you must hold the handgrip pulse sensor fre-
quently. Each time you hold the handgrip pulse
sensor, keep your hands on the metal con-
tacts for at least 15 seconds. Note: When you
are not holding the handgrip pulse sensor, the let-
ters “PLS” will appear in the display instead of
your heart rate.
If the speed or incline setting is too high or too low
at any time during the program, you can adjust the
setting with the Speed or Incline buttons. However,
when the console compares your heart rate to the
target heart rate setting, the speed of the treadmill
may automatically change to bring your heart rate
closer to the target heart rate setting.
Press the Start button or the Speed increase
button to start the program.
A moment after the button is pressed, the tread-
mill will automatically adjust to the first speed and
incline settings of the program. Hold the handrails
and begin walking.
If your pulse is not detected during the program,
the letters “PLS” will flash in the right display and
the speed of the treadmill may automatically de-
crease.
Heart rate program 11 is divided into several
one-minute segments. The same target heart rate
setting is programmed for all segments. (For a
shorter workout, simply stop the program before it
ends.) Heart rate programs 12, 13, and 14 are
divided into either 20 or 30 one-minute segments.
One target heart rate setting is programmed for
each segment. Note: The same target heart rate
setting may be programmed for two or more con-
secutive segments.
To stop the program at any time, press the Stop
button. To restart the program, press the Start but-
ton or the Speed increase button. The walking belt
will begin to move at 1 mph. When the console
compares your heart rate to the target heart rate
setting, the speed and/or incline of the treadmill
may automatically change to bring your heart rate
closer to the target heart rate setting.
If heart rate program
12, 13, or 14 is se-
lected, the target heart
rate setting for the first
segment will be shown
in the flashing Current
Segment column of
the matrix. The target
Follow your progress with the displays.
See step 5 on page 12.
Current Segment
7
8
9
Column
Turn on the fan if desired.
See step 7 on page 13.
heart rate settings for
When you are finished exercising, remove the
key from the console.
the next several segments will be shown in the
columns to the right. When only three seconds re-
main in the first segment of the program, both the
Current Segment column and the column to the
right will flash and a series of tones will sound.
See step 7 on page 15.
When the first segment ends, all target heart rate
settings will move one column to the left. The tar-
get heart rate setting for the second segment will
then be shown in the flashing Current Segment
column.
19
Download from Www.Somanuals.com. All Manuals Search And Download.
HOW TO OPERATE THE PERSONAL TELEVISION
HOW TO USE THE INFORMATION MODE
The console features an information mode that allows
you to view treadmill usage information, select a sys-
tem of measurement for the console, and turn on and
turn off the demo mode. The information mode also al-
lows you to adjust the settings of the television and to
save channels into the television’s memory.
IMPORTANT: Before operating the television, you
must connect a 75 ohm CATV cable to the 75 ohm
terminal on the treadmill. See page 9 for instruc-
tions.
Follow the steps below to operate the television.
Follow the steps below to use the information mode.
Insert the key into the console.
1
Hold down the Stop button while inserting the
key into the console.
See HOW TO TURN ON THE POWER on page
12.
1
When the information mode is selected, the left
display will show the total number of hours that the
treadmill has been used. The right display will
show the total number of miles or kilometers that
the walking belt has moved.
Press the Power button to turn on the
television.
2
When the key is inserted, the television will auto-
matically turn on. If you have turned off the televi-
sion, turn it on by pressing the Power button.
In addition, the right display will show the letter “E”
for English miles or the letter “M” for metric kilome-
ters. Press the Speed increase button to change
the unit of measurement if desired.
Press the Channel buttons to select the
desired cable channel.
3
Note: Complete this step only if you are using
analog cable. Otherwise, change channels
through an external source such as your cable
box or your VCR.
IMPORTANT: If the letter “d” appears in the right
display, the “demo” mode is selected. This mode
is intended to be used only when a treadmill is
displayed in a store. When the demo mode is se-
lected, the power cord can be plugged in, the key
can be removed from the console, and the dis-
plays and indicators on the console will automati-
cally light in a preset sequence. The buttons on
the console will not function. If a “d” appears in
the right display when the information mode is
selected, press the Speed decrease button.
When the television is turned on, the screen will
show the last cable channel that was selected. To
select a different channel, press the Channel but-
tons. The selected cable channel number will ap-
pear on the screen for a few seconds. Note: The
television is equipped with a channel memorizing
function that allows you to go directly from the cur-
rent channel to the next channel saved in mem-
ory. Before channels can be selected in this way,
they must be saved in the television’s memory.
See HOW TO USE THE INFORMATION MODE
at the right.
Press the Power button and adjust the
brightness, contrast, color, sharpness, and/or
hue of the television.
2
When the Power button is pressed, the brightness
level indicator will appear on the television screen.
Press the Volume buttons to adjust the brightness
setting if desired.
Press the Volume buttons to adjust the volume.
4
When either Volume button is pressed, the vol-
ume level indicator will appear on the screen for a
few seconds. To temporarily mute the sound,
press the Mute button. Press the Mute button
again to listen to the television. Note: To use ear-
phones or headphones (not included), plug them
into the headphone jack on the console.
Next, press the Channel buttons until the contrast,
color, sharpness, or hue level indicator appears.
Adjust the settings, if desired, by pressing the
Volume buttons.
When you are finished using the television,
press the Power button.
5
Press the Power button to turn off the television.
Note: Removing the key from the console will also
turn off the television.
20
Download from Www.Somanuals.com. All Manuals Search And Download.
able in your area. When no cable signal is de-
tected on a channel, the channel will be skipped.
When a cable signal is detected, the channel will
be saved into memory and the next channel will
be selected. This process will continue until the
highest channel is reached. Do not remove the
key while the television is scanning channels.
Note: If you are viewing channels through an ex-
ternal source such as a cable box or a VCR, the
television will save only the channel used by the
external source.
Press the Power button again and add or
delete cable channels.
3
Note: Complete this step only if you are using
analog cable.
After all valid cable channels available in your
area have been saved into the television’s mem-
ory (see step 5 below), you can manually add
channels or delete unwanted channels.
To add or delete a cable channel, first press the
Channel buttons until the desired channel number
appears on the screen. Then, press the Volume
increase button to add the channel, or the Volume
decrease button to delete the channel. Continue
this process until you have added all desired
channels and deleted all unwanted channels.
When you are finished using the information
mode, remove the key.
6
To exit the information mode at any time (except
while the television is scanning channels), remove
the key from the console.
Press the Power button again and select a
cable connection.
4
5
HOW TO ADJUST THE CUSHIONING SYSTEM
If you have connected a CATV cable, one of the
three Cable settings should be selected; try all
three Cable settings, if necessary, to find the opti-
mal setting. Press the Volume increase button to
select the Standard Cable setting, the Channel
decrease button to select the Cable IRC setting,
or the Channel increase button to select the Cable
HRC setting. Note: The setting that you select will
not appear on the screen.
The treadmill features
a cushioning system
that reduces the im-
pact as you walk or
run on the treadmill.
To increase the firm-
ness of the walking
platform, turn the ad-
justment knob coun-
terclockwise. To de-
crease the firmness,
Adjustment
Knob
Press the Power button again and save cable
channels into the television’s memory.
turn the knob clockwise. Note: The faster you run on
the treadmill, or the more you weigh, the firmer the
walking platform should be.
When the Power button is pressed, the television
will begin scanning all of the cable channels avail-
21
Download from Www.Somanuals.com. All Manuals Search And Download.
HOW TO FOLD AND MOVE THE TREADMILL
HOW TO FOLD THE TREADMILL FOR STORAGE
1
Before folding the treadmill, adjust the incline to the
lowest position. If this is not done, the treadmill may be
permanently damaged. Next, unplug the power cord.
CAUTION: You must be able to safely lift 45 pounds (20
kg) to raise, lower, or move the treadmill.
1. Hold the treadmill in the locations shown at the right. To
decrease the possibility of injury, bend your legs and
keep your back straight. As you raise the frame, make
sure to lift with your legs rather than your back. Raise
the frame about halfway to the vertical position.
2. Hold the frame firmly with your left hand. Using your right
2
hand, pull the latch knob to the right and hold it. Raise
the treadmill until the pin on the latch knob is aligned with
the hole in the left handgrip. Then, release the latch
knob. Make sure that the latch knob is fully released
so the pin is fully inserted into the hole in the left
Frame
handgrip.
Latch
Knob
Latch
Knob
Pin
To protect the floor or carpet from damage, place a
mat under the treadmill. Keep the treadmill out of
direct sunlight. Do not leave the treadmill in the stor-
age position in temperatures above 85° Fahrenheit.
Handgrip
Pin
Handgrip
HOW TO MOVE THE TREADMILL
Before moving the treadmill, convert the treadmill to the
storage position as described above. Make sure that the
pin on the latch knob is fully inserted into the hole in the
left handgrip.
1. Hold the handgrips and place one foot against one of the
wheels.
2. Tilt the treadmill back until it rolls freely on the wheels.
Carefully move the treadmill to the desired location. To re-
duce the risk of injury, use extreme caution while
moving the treadmill. Do not attempt to move the
treadmill over an uneven surface.
Base
3. Place one foot against a wheel, and carefully lower the
treadmill until the base is in the storage position.
Wheel
HOW TO LOWER THE TREADMILL FOR USE
1. See drawing 2 above. Hold the treadmill frame firmly with your left hand. Pull the latch knob to the right. Pivot
the frame down until the pin on the latch knob is below the handgrip. Then, slowly release the latch knob.
2. See drawing 1 above. Hold the frame firmly with both hands, and lower the frame to the floor. To decrease
the possibility of injury, bend your legs and keep your back straight.
22
Download from Www.Somanuals.com. All Manuals Search And Download.
TROUBLESHOOTING
Most treadmill problems can be solved by following the steps below. Find the symptom that applies, and
follow the steps listed. If further assistance is needed, see the front cover of this manual.
PROBLEM: The power does not turn on
SOLUTION: a. Make sure that the power cord is plugged into a surge suppressor, and that the surge suppressor
is plugged into a properly grounded outlet (see page 10). Use only a single-outlet surge suppres-
sor that meets all of the specifications described on page 10. Important: The treadmill is not com-
patible with GFCI-equipped outlets.
b. After the power cord has been plugged in, make sure that the key is inserted into the console.
c. Check the reset/off circuit breaker located on the treadmill frame
near the power cord. If the switch protrudes as shown, the circuit
breaker has tripped. To reset the circuit breaker, wait for five min-
utes and then press the switch to the reset position.
Reset
Tripped
PROBLEM: The power turns off during use
SOLUTION: a. Check the reset/off circuit breaker (see the drawing above). If the circuit breaker has tripped, wait
for five minutes and then press the switch to the reset position.
b. Make sure that the power cord is plugged in. If the power cord is plugged in, unplug it, wait for
five minutes, and then plug it back in.
c. Remove the key from the console and then reinsert it.
d. Make sure that the reset/off circuit breaker is in the on position (see 1. d. above).
e. If the treadmill still will not run, see the front cover of this manual.
PROBLEM: The walking belt slows when walked on
SOLUTION: a. Use only a single-outlet surge suppressor that meets all of the specifications described on page 10.
b. If the walking belt is overtightened, treadmill performance
b
may decrease and the walking belt may be permanently
damaged. Remove the key and UNPLUG THE POWER
CORD. Using the included allen wrench, turn both rear
roller bolts counterclockwise 1/4 of a turn. When the walk-
ing belt is properly tightened, you should be able to lift
each edge of the walking belt 3 to 4 inches off the walking
platform. Be careful to keep the walking belt centered.
Then, plug in the power cord, insert the key and run the
treadmill for a few minutes. Repeat until the walking belt
is properly tightened.
3–4”
Rear Roller Bolts
c. If the walking belt still slows when walked on, see the front cover of this manual.
23
Download from Www.Somanuals.com. All Manuals Search And Download.
PROBLEM: The walking belt is off-center or slips when walked on
SOLUTION: a. If the walking belt is off-center, first remove the key and
UNPLUG THE POWER CORD. If the walking belt has
shifted to the left, use the allen wrench to turn the left
rear roller bolt clockwise 1/2 of a turn; if the walking belt
has shifted to the right, turn the bolt counterclockwise
1/2 of a turn. Be careful not to overtighten the walking belt.
Then, plug in the power cord, insert the key, and run the
treadmill for a few minutes. Repeat until the walking belt is
centered.
a
b. If the walking belt slips when walked on, first remove the
key and UNPLUG THE POWER CORD. Using the allen
wrench, turn both rear roller bolts clockwise 1/4 of a turn.
When the walking belt is correctly tightened, you should be
able to lift each edge of the walking belt 3 to 4 inches off
the walking platform. Be careful to keep the walking belt
centered. Then, plug in the power cord, insert the key, and
walk on the treadmill for a few minutes. Repeat until the
walking belt is properly tightened.
b
PROBLEM: The displays of the console do not function properly
SOLUTION: a. Remove the key from the console and UNPLUG THE
POWER CORD. Next, remove the screws from the hood
and carefully remove the hood. Locate the Reed Switch
(17) and the Magnet (12) on the left side of the Pulley (11).
Turn the Pulley until the Magnet is aligned with the Reed
Switch. Make sure that the gap between the Magnet
and the Reed Switch is about 1/8”. If necessary, move
the Reed Switch slightly using a slotted screwdriver. Re-at-
tach the hood and run the treadmill for a few minutes to
check for a correct speed reading.
a
1/8”
17
11
12
Top
View
PROBLEM: Television reception is poor
SOLUTION: a. Check for the problems listed below and follow the applicable instructions.
• Ignition (black spots or horizontal streaks that appear or a picture that flutters or drifts)—Usually
this is caused by interference from automobile ignition systems, neon lamps, electric drifts, or
other electric appliances. Try changing the position of other electric appliances to correct the
problem. Make sure that the treadmill is plugged into its own electrical circuit.
• Ghosts—Ghosts are caused by the television signal following two paths—one is the direct path
and the other is reflected from tall buildings, hills, or other objects.
• Blue Screen—If the cable channel signal is weak, the picture may be of poor quality or a blue
screen may appear.
Note: If one of these symptoms appears, the symptom may be caused by the local cable com-
pany signal reception. Contact the local cable company.
24
Download from Www.Somanuals.com. All Manuals Search And Download.
EXERCISE GUIDELINES
begin to use stored fat calories for energy. If your goal
is to burn fat, adjust the speed or incline of the tread-
mill until your heart rate is near the lowest number in
your training zone.
WARNING:
Before beginning this
or any exercise program, consult your physi-
cian. This is especially important for individu-
als over the age of 35 or individuals with pre-
existing health problems.
For maximum fat burning, adjust the speed or incline
of the treadmill until your heart rate is near the middle
number in your training zone.
The pulse sensor is not a medical device.
Various factors, including the user's move-
ment, may affect the accuracy of heart rate
readings. The pulse sensor is intended only
as an exercise aid in determining heart rate
trends in general.
Aerobic Exercise
If your goal is to strengthen your cardiovascular sys-
tem, your exercise must be “aerobic.” Aerobic exercise
is activity that requires large amounts of oxygen for
prolonged periods of time. This increases the demand
on the heart to pump blood to the muscles, and on the
lungs to oxygenate the blood. For aerobic exercise,
adjust the speed or incline of the treadmill until your
heart rate is near the highest number in your training
zone.
The following guidelines will help you to plan your ex-
ercise program. For more detailed exercise informa-
tion, obtain a reputable book or consult your physician.
EXERCISE INTENSITY
WORKOUT GUIDELINES
Whether your goal is to burn fat or to strengthen your
cardiovascular system, the key to achieving the
desired results is to exercise with the proper intensity.
The proper intensity level can be found by using your
heart rate as a guide. The chart below shows recom-
mended heart rates for fat burning and aerobic exercise.
Each workout should include the following three parts:
A Warm-up—Start each workout with 5 to 10 minutes
of stretching and light exercise. A proper warm-up in-
creases your body temperature, heart rate and circula-
tion in preparation for exercise.
Training Zone Exercise—After warming up, increase
the intensity of your exercise until your pulse is in your
training zone for 20 to 60 minutes. (During the first few
weeks of your exercise program, do not keep your
pulse in your training zone for longer than 20 minutes.)
Breathe regularly and deeply as you exercise—never
hold your breath.
To find the proper heart rate for you, first find your age
near the bottom of the chart (ages are rounded off to
the nearest ten years). Next, find the three numbers
above your age. The three numbers define your “train-
ing zone.” The lower two numbers are recommended
heart rates for fat burning; the highest number is the
recommended heart rate for aerobic exercise.
A Cool-down—Finish each workout with 5 to 10 min-
utes of stretching to cool down. This will increase the
flexibility of your muscles and will help prevent post-ex-
ercise problems.
EXERCISE FREQUENCY
Fat Burning
To maintain or improve your condition, complete three
workouts each week, with at least one day of rest be-
tween workouts. After a few months, you may com-
plete up to five workouts each week if desired. The key
to success is to make exercise a regular and enjoyable
part of your everyday life.
To burn fat effectively, you must exercise at a relatively
low intensity level for a sustained period of time.
During the first few minutes of exercise, your body
uses easily accessible carbohydrate calories for en-
ergy. Only after the first few minutes does your body
25
Download from Www.Somanuals.com. All Manuals Search And Download.
PART LIST—Model No. PFTL94105.1
R1207A
To locate the parts listed below, see the EXPLODED DRAWING attached in the center of this manual.
Key No. Qty.
Description
Key No. Qty.
Description
1
2
3
4
5
6
7
8
2
1
1
4
1
1
2
1
2
4
1
1
9
2
2
1
1
1
2
2
10
1
4
1
1
4
4
1
2
1
1
2
2
1
1
1
1
1
1
48
1
2
6
12
1
1
1
2
1
1
Foot Rail
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
85
86
87
88
89
90
91
92
93
94
95
96
97
98
99
100
1
2
2
1
1
1
2
1
4
2
1
4
1
1
1
4
1
1
4
5
1
1
4
1
2
2
2
2
1
1
1
1
2
4
1
1
2
2
1
1
1
1
2
2
2
1
12
2
1
1
Hood Cover
Left Outside Housing
Left Handgrip, Top
Isolator
Latch Housing Cover
Platform
Walking Platform Screw
Walking Belt
Frame Pivot Bolt
Frame Pivot Washer
Front Wheel/Pulley
Magnet
Front Roller Nut/Front Wheel Nut
Spacer Insert
Frame Pivot Spacer
Reed Switch Clip
Reed Switch
Lift Frame
Foot Rail Insert
Gear Rack
Foot Rail Screw
Motor Belt
1” Screw
Drive Motor
Transformer
Cushion Adj. Housing Screw
Hood Bracket
Ground Wire
Isolator Screw
Right Rear Endcap
Lift Motor Bolt
Base Pad Screw
Rear Roller Adjustment Bolt
Left Rear Endcap
Frame
Allen Wrench
Rear Platform Screw
Rear Roller
Foot Screw
Cable Nut
Pulse Bar
Spring Nut
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
Idler Arm
Idler Spring
Upright/Base
Belt Guide Screw
Console Frame
Latch Housing
Console Washer
Hood Screw
Console Wire Harness
iFIT.com Wire
Wire Tie
Flywheel
Spring
Spring Pad Screw
Front Wheel
Wheel Bolt
Pulley Nut
Console
Console Base
Console Fan
Spring Pad
Belly Pan Screw
Upright Wire Harness
Shock
Spring Plate Spacer
Upright Endcap
Filter Wire
Latch Warning Decal
Incline Motor
Motor Controller Wire
Fan Screw
Motor Bolt
Cushion Plate
Left Inside Housing
Right Inside Housing
Right Outside Housing
Controller
Controller Bracket
Motor Hood
3/4” Screw
Motor Belly Pan
Belt Guide
3/4” Tek Screw
Electronics Screw
Left Front Endcap
Right Front Endcap
Ground Screw
Rear Foot
Tie Holder Screw
Tie Holder
Tie
8” Cable Tie
Base Pad
Console Ground Wire
Fan Housing
Idler Arm Bolt
Upright TV Cable
26
Download from Www.Somanuals.com. All Manuals Search And Download.
Key No. Qty.
Description
Key No. Qty.
Description
101
102
103
104
105
106
107
108
109
110
111
112
113
114
115
116
117
118
119
120
121
122
123
124
125
126
127
1
1
1
2
2
1
1
2
2
1
1
5
1
2
1
8
1
1
4
2
2
1
1
1
1
1
1
Pulse Wire
Power Cord Assembly
TV Console
Warning Decal
Spring Plate
Left Handgrip, Bottom
Warning Decal, Pulse Bar
Rear Roller Star Washer
Idler Arm Washer
Idler Pulley
Pulley Spacer
Outlet Bracket Star Washer
Static Decal
1/2” Tek Screw
Idler Pulley Bolt
Spring Washer/Deck Rail Washer
Console Back
Latch Assembly
Spring Bolt
Cushion Adj. Pin
Motor Bushing
Idler Arm Spacer
Cushion Adj. Rod
Incline Bracket
Incline Motor Bolt, Bottom
Right Handgrip, Top
Motor Isolator Plate
128
129
130
131
132
133
134
135
136
137
138
139
140
141
142
#
#
#
#
#
#
#
#
2
2
1
1
2
4
4
1
1
2
1
4
2
4
1
1
1
1
1
1
1
1
1
Cushion Adj. Gear
Cushion Adj. Wheel
Cushion Adj. Knob
Cushion Adj. Screw
1/2” Screw
1” Console Bolt
Pulse Bar Screw
Access Door
Key/Clip
Wheel Housing
Right Handgrip, Bottom
U-nut
Handgrip Screw
Rear Foot Lock Washer
Transformer Bracket
8” Blue Wire, 2 F
4” Blue Wire, M/F
4” Blue Wire, 2 F
Blue Wire, M/F
12” Green Wire, F/Ring
8” Green Wire, 2 Ring
14” White Wire, 2 F
4” Black Wire, 2 F
#These parts are not illustrated
Specifications are subject to change without notice.
27
Download from Www.Somanuals.com. All Manuals Search And Download.
EXPLODED DRAWING—Model No. PFTL94105.1
R1207A
To identify the parts shown on this
EXPLODED DRAWING, see the
PART LIST on pages 26 and 27.
Download from Www.Somanuals.com. All Manuals Search And Download.
EXPLODED DRAWING—Model No. PFTL94105.1
R1207A
Download from Www.Somanuals.com. All Manuals Search And Download.
ORDERING REPLACEMENT PARTS
To order replacement parts, please see the front cover of this manual. To help us assist you, be prepared to
provide the following information:
• the MODEL NUMBER of the product (PFTL94105.1)
• the NAME of the product (PROFORM PRO SERIES 1500 treadmill)
• the SERIAL NUMBER of the product (see the front cover of this manual)
• the KEY NUMBER and DESCRIPTION of the part(s) (see the PART LIST on pages 26 and 27 and the EX-
PLODED DRAWING in the center of this manual)
LIMITED WARRANTY
ICON Health & Fitness, Inc. (ICON) warrants this product to be free from defects in workmanship and
material under normal use and service conditions. The drive motor is warranted for twenty (20) years
after the date of purchase. Parts and labor are warranted for one (1) year after the date of purchase.
This warranty extends only to the original purchaser. ICON's obligation under this warranty is limited to
replacing or repairing, at ICON's option, the product through one of its authorized service centers. All re-
pairs for which warranty claims are made must be pre-authorized by ICON. If the product is shipped to a
service center, freight charges to and from the service center will be the customer’s responsibility. For in-
home service, the customer will be responsible for a minimal trip charge. This warranty does not extend
to any product or damage to a product caused by or attributable to freight damage, abuse, misuse, im-
proper or abnormal usage or repairs not provided by an ICON authorized service center; products used
for commercial or rental purposes; or products used as store display models. No other warranty beyond
that specifically set forth above is authorized by ICON.
ICON is not responsible or liable for indirect, special or consequential damages arising out of or in con-
nection with the use or performance of the product or damages with respect to any economic loss, loss
of property, loss of revenues or profits, loss of enjoyment or use, costs of removal or installation or other
consequential damages of whatsoever nature. Some states do not allow the exclusion or limitation of in-
cidental or consequential damages. Accordingly, the above limitation may not apply to you.
The warranty extended hereunder is in lieu of any and all other warranties and any implied warranties of
merchantability or fitness for a particular purpose is limited in its scope and duration to the terms set
forth herein. Some states do not allow limitations on how long an implied warranty lasts. Accordingly, the
above limitation may not apply to you.
This warranty gives you specific legal rights. You may also have other rights which vary from state to state.
ICON HEALTH & FITNESS, INC., 1500 S. 1000 W., LOGAN, UT 84321-9813
Part No. 262674 R1207A
Printed in USA © 2007 ICON IP, Inc.
Download from Www.Somanuals.com. All Manuals Search And Download.
|