Model No. PFTL79506.0
Serial No.
USER'S MANUAL
Serial Number Decal
QUESTIONS?
As a manufacturer, we are com-
mitted to providing complete
customer satisfaction. If you
have questions, or if parts are
damaged or missing, PLEASE
CONTACT OUR CUSTOMER
SERVICE DEPARTMENT
DIRECTLY.
CALL TOLL-FREE:
1-888-533-1333
Mon.–Fri., 6 a.m.–6 p.m. MST
ON THE WEB:
CAUTION
Read all precautions and instruc-
tions in this manual before using
this equipment. Save this manual
for future reference.
Visit our website at
new products, prizes,
fitness tips, and much more!
Download from Www.Somanuals.com. All Manuals Search And Download.
IMPORTANT PRECAUTIONS
WARNING:
To reduce the risk of burns, fire, electric shock, or injury to persons, read the
following important precautions and information before operating the treadmill.
1. It is the responsibility of the owner to ensure
that all users of this treadmill are adequately
informed of all warnings and precautions.
see your local PROFORM dealer or call the
toll-free telephone number on the front cover
of this manual and order part number 146148,
or see your local electronics store.
2. Use the treadmill only as described.
12. Failure to use a properly functioning surge
suppressor could result in damage to the con-
trol system of the treadmill. If the control sys-
tem is damaged, the walking belt may change
speed, accelerate, or stop unexpectedly,
3. Place the treadmill on a level surface, with at
least eight feet of clearance behind it and two
feet on each side. Do not place the treadmill
on any surface that blocks air openings. To
protect the floor or carpet from damage, place
a mat under the treadmill.
which may result in a fall and serious injury.
13. Keep the power cord and the surge suppres-
sor away from heated surfaces.
4. Keep the treadmill indoors, away from mois-
ture and dust. Do not put the treadmill in a
garage or covered patio, or near water.
14. Never move the walking belt while the power
is turned off. Do not operate the treadmill if
the power cord or plug is damaged, or if the
treadmill is not working properly. (See TROU-
BLESHOOTING on page 20 if the treadmill is
not working properly.)
5. Do not operate the treadmill where aerosol
products are used or where oxygen is being
administered.
6. Keep children under the age of 12 and pets
away from the treadmill at all times.
15. Read, understand, and test the emergency
stop procedure before using the treadmill (see
HOW TO TURN ON THE POWER on page 12).
7. The treadmill should be used only by persons
weighing 300 pounds or less.
16. Never start the treadmill while you are stand-
ing on the walking belt. Always hold the
handrails while using the treadmill.
8. Never allow more than one person on the
treadmill at a time.
9. Wear appropriate exercise clothes when
using the treadmill. Do not wear loose clothes
that could become caught in the treadmill.
Athletic support clothes are recommended for
both men and women. Always wear athletic
shoes. Never use the treadmill with bare feet,
wearing only stockings, or in sandals.
17. The treadmill is capable of high speeds.
Adjust the speed in small increments to avoid
sudden jumps in speed.
18. The pulse sensor is not a medical device.
Various factors, including the user's move-
ment, may affect the accuracy of heart rate
readings. The pulse sensor is intended only
as an exercise aid in determining heart rate
trends in general.
10. When connecting the power cord (see page
10), plug the power cord into a surge sup-
pressor (not included) and plug the surge
suppressor into a grounded circuit capable of
carrying 15 or more amps. No other appliance
should be on the same circuit. Do not use an
extension cord.
19. Use the included dumbbells only as de-
scribed in this manual. Properly store the
dumbbells in the dumbbell holders on the
console when you are not using them (see
page 5). If the dumbbells are improperly
stored, they may fall off the console, causing
the user to trip.
11. Use only a single-outlet surge suppressor
that meets all of the specifications described
on page 10. To purchase a surge suppressor,
3
Download from Www.Somanuals.com. All Manuals Search And Download.
20. Never leave the treadmill unattended while it
is running. Always remove the key, unplug
the power cord, and switch the reset/off cir-
cuit breaker to the off position when the
treadmill is not in use. (See the drawing on
page 5 for the location of the circuit breaker.)
24. Inspect and properly tighten all parts of the
treadmill regularly.
25.
DANGER:
Always unplug the power
cord immediately after use, before cleaning the
treadmill, and before performing the mainte-
nance and adjustment procedures described in
this manual. Never remove the motor hood un-
less instructed to do so by an authorized ser-
vice representative. Servicing other than the
procedures in this manual should be performed
by an authorized service representative only.
21. Do not attempt to raise, lower, or move the
treadmill until it is properly assembled. (See
ASSEMBLY on page 6, and HOW TO FOLD
AND MOVE THE TREADMILL on page 19.)
You must be able to safely lift 45 pounds (20
kg) to raise, lower, or move the treadmill.
26. This treadmill is intended for in-home use
only. Do not use this treadmill in a commer-
cial, rental, or institutional setting.
22. When folding or moving the treadmill, make
sure that the storage latch is fully closed.
23. Never insert any object into any opening on
the treadmill.
WARNING:
Before beginning this or any exercise program, consult your physician. This
is especially important for persons over the age of 35 or persons with pre-existing health problems.
Read all instructions before using. ICON assumes no responsibility for personal injury or property
damage sustained by or through the use of this product.
SAVE THESE INSTRUCTIONS
The decals shown here have been placed on the treadmill. If a
decal is missing, or if it is illegible, call the toll-free telephone
number on the front cover of this manual and order a free re-
placement decal. Apply the decal in the location shown.
4
Download from Www.Somanuals.com. All Manuals Search And Download.
BEFORE YOU BEGIN
Thank you for selecting the revolutionary PROFORM®
755 CROSSTRAINER treadmill. The 755 CROSS-
TRAINER treadmill offers an impressive array of fea-
tures designed to make your workouts at home more
enjoyable and effective. And when you’re not exercis-
ing, the unique 755 CROSSTRAINER treadmill can be
folded up, requiring less than half the floor space of
other treadmills.
ual. To help us assist you, note the product model num-
ber and serial number before contacting us. The model
number of the treadmill is PFTL79506.0. The serial
number can be found on a decal attached to the tread-
mill (see the front cover of this manual for the location).
To avoid a registration fee for any service needed
under warranty, you must register the treadmill at
For your benefit, read this manual carefully before
you use the treadmill. If you have questions after read- Before reading further, please review the drawing
ing this manual, please see the front cover of this man-
below and familiarize yourself with the labeled parts.
Fan
Console
Dumbbell/Water Bottle Holder*
Handgrip Pulse Sensor
Key/Clip
Handrail
Upright
Walking Belt
Reset/Off
Circuit Breaker
Power Cord
Foot Rail
RIGHT SIDE
Cushioned Walking Platform
for maximum exercise comfort
BACK
Rear Roller
Adjustment Bolts
*No water bottle is included
5
Download from Www.Somanuals.com. All Manuals Search And Download.
ASSEMBLY
To hire an authorized service technician to assemble the treadmill, call toll-free 1-800-445-2480.
Assembly requires two persons. Set the treadmill in a cleared area and remove all packing materials. Do not
dispose of the packing materials until assembly is completed. Note: The underside of the treadmill walking belt is
coated with high-performance lubricant. During shipping, a small amount of lubricant may be transferred to the
top of the walking belt or the shipping carton. This is a normal condition and does not affect treadmill perfor-
mance. If there is lubricant on top of the walking belt, simply wipe off the lubricant with a soft cloth and a mild,
non-abrasive cleaner.
Assembly requires the included hex key
shaft at least 6" long) and wire cutters
and your own phillips screwdriver
.
(with a
Use the drawings below to identify the hardware used during assembly. Note: If a part is not in the parts bag,
check to see if it has been preattached to one of the parts to be assembled. To avoid damaging plastic
parts, do not use power tools for assembly.
Screw (3)–9
Ground Screw
(33)–1
3/4” Screw (22)–4
Upper Latch Shock Bolt (50)–1
Lower Latch Shock Bolt (39)–1
Extension Leg Nut (67)–4
Nut (30)–2
Extension Leg Bolt (65)–4
Handrail Bolt (64)–4
Star Washer (8)–4
1. Make sure that the power cord is unplugged.
1
With the help of a second person, carefully tip
the treadmill onto its left side as shown.
84
65
Insert an Extension Leg (89) into the base of the
Uprights (84) as shown. Hold two Extension Leg
Nuts (67) in the bottom of the Extension Leg.
Next, insert two Extension Leg Bolts (65) into the
top of the Extension Leg, and firmly tighten the
Extension Leg Bolts into the Extension Leg Nuts.
82
22
82
22
Attach two Base Pads (82) to the base of the
Uprights (84) with two 3/4” Tek Screws (22).
89
67
6
Download from Www.Somanuals.com. All Manuals Search And Download.
2. With the help of a second person, carefully tip
the treadmill onto its right side as shown.
2
84
Insert the other Extension Leg (89) into the base
of the Uprights (84) as shown. Hold two
Extension Leg Nuts (67) in the bottom of the
Extension Leg. Next, insert two Extension Leg
Bolts (65) into the top of the Extension Leg, and
firmly tighten the Extension Leg Bolts into the
Extension Leg Nuts.
65
22
82
22
58
Attach two Base Pads (82) to the base of the
Uprights (84) with two 3/4” Tek Screws (22).
67
89
With the help of a second person, carefully raise
the treadmill so that all four Base Pads (22) are
on the floor and the Frame (58) is in a vertical
position (see drawing 3).
3. Make sure that the sleeve has been slid over
hole 1 and that the latch knob is locked into hole
1. Pull on the sleeve to make sure it is locked
into place.
3
Hole 2
Next, make sure that the latch knob is locked
into hole 2. If it is not, pull out the tube until you
see hole 2 and then slide the tube back in until
the latch knob locks into hole 2.
Latch Knob
Hole 1
Tube
Sleeve
4. Remove the plastic ties from the ends of the
Latch Shock (69).
4
58
Hold the Latch Shock (29) with the large barrel
and latch knob positioned as shown; make sure
all of the holes are aligned (see the inset draw-
ings). Next, attach the lower end of the Latch
Shock to the bracket on the Upright (84) with the
Lower Latch Shock Bolt (39) and a Nut (30).
30
50
Top
Holes
Latch Knob
29
Then, attach the upper end of the Latch Shock
(29) to the bracket on the Frame (58) with the
Upper Latch Shock Bolt (50) and a Nut (30).
Note: It may be necessary to move the Frame
back and forth to align the Latch Shock with the
Bracket.
Large
Barrel
84
Holes
30
Bottom
39
7
Download from Www.Somanuals.com. All Manuals Search And Download.
5. Lower the treadmill frame (see HOW TO
LOWER THE TREADMILL FOR USE on page
19).
5
6
7
64
8
Have a second person hold the Handrail (20)
near the Uprights (84). Insert the Upright Wire
Harness (77) into the hole in the bottom of the
Handrail and out of the top as shown.
20
64
8
77
Next, set the Handrail (20) on the Uprights (84).
Do not let the Upright Wire Harness (77) fall
into the right Upright.
84
Attach the Handrail (20) with four Handrail Bolts
(64) and four Star Washers (8); start all four
Handrail Bolts and then firmly tighten them.
84
6. While a second person holds the console as-
sembly near the Handrail (20), attach the ground
wire to the indicated hole in the Handrail with a
Ground Screw (33).
Ground
Wire
33
Hole
20
Console
Assembly
7. While the second person continues to hold the
console assembly, locate the wire harness un-
derneath the console assembly.
Connect the wire harness from the console as-
sembly to the Upright Wire Harness (77). Make
sure to connect the connectors properly (see
the inset drawing). The connectors should
slide together easily and snap into place. If
the connectors do not slide together easily and
snap into place, turn one connector and then try
again. IF THE CONNECTORS ARE NOT CON-
NECTED PROPERLY, THE CONSOLE MAY
BE DAMAGED WHEN THE POWER IS
77
Wire
Console
Assembly
77
TURNED ON. Then, insert the connectors down-
ward into the Handrail (20).
20
8
Download from Www.Somanuals.com. All Manuals Search And Download.
8. Set the console assembly on the Handrail (20).
Be careful to avoid pinching any of the wires.
Make sure that the ground wire (see step 6)
and the wire harness from the console as-
sembly (see step 7) are in the indicated chan-
nel.
8
Console Assembly
Channel
Hand tighten five Screws (3) into the Handrail
(20) and the console assembly. Start all five
Screws, but do not tighten them yet. Do not
put Screws into the two indicated holes.
20
3
3
3
No Screws
9. Hand tighten four additional Screws (3) into the
Handrail (20) and the console assembly. Then,
tighten all nine Screws used in step 8 and
this step; do not overtighten the Screws.
9
Console Assembly
3
20
3
10.Make sure that all parts are properly tightened before you use the treadmill. If there are sheets of clear
plastic on the treadmill decals, remove the plastic. To protect the floor or carpet, place a mat under the tread-
mill. Note: Extra hardware may be included. Keep the included hex key in a secure place; the large hex key is
used to adjust the walking belt (see page 21).
If you purchase the optional chest pulse sensor (see page 18), follow the steps below to install the receiver
included with the chest pulse sensor.
1. Remove the key from the console and unplug
85
the power cord.
Remove the Screw (3) and the Access Door (76)
from the back of the Console Base (85).
2. Connect the wire on the receiver (A) to the indi-
cated wire extending from the Console Base
(85). Hold the receiver so the small cylinder is
oriented as shown and is facing the Console
Small Screws
Base. Attach the receiver to the plastic posts on
Wire
the Access Door (76) with the two included small
screws.
A
Small
Cylinder
3. Make sure that no wires are pinched. Reattach
the Access Door (76) with the Screw (3). Discard
3
76
the other wires included with the receiver.
9
Download from Www.Somanuals.com. All Manuals Search And Download.
OPERATION AND ADJUSTMENT
THE PRE-LUBRICATED WALKING BELT
tric shock. This product is equipped with a cord having
an equipment-grounding conductor and a grounding
plug. Plug the power cord into a surge suppressor,
and plug the surge suppressor into an appropriate
outlet that is properly installed and grounded in
accordance with all local codes and ordinances.
Important: The treadmill is not compatible with
GFCI-equipped outlets.
Your treadmill features a walking belt coated with high-
performance lubricant. IMPORTANT: Never apply sil-
icone spray or other substances to the walking
belt or the walking platform. Such substances will
deteriorate the walking belt and cause excessive
wear.
HOW TO PLUG IN THE POWER CORD
This product is for use on a nominal 120-volt circuit,
and has a grounding plug that looks like the plug illus-
trated in drawing 1 below. A temporary adapter that
looks like the adapter illustrated in drawing 2 may be
used to connect the surge suppressor to a 2-pole
receptacle as shown in drawing 2 if a properly
grounded outlet is not available.
DANGER:
Improper connection
of the equipment-grounding conductor can
result in an increased risk of electric shock.
Check with a qualified electrician or service-
man if you are in doubt as to whether the
product is properly grounded. Do not modify
the plug provided with the product—if it will
not fit the outlet, have a proper outlet
1
Grounded Outlet Box
Surge Suppressor
Grounding Pin
installed by a qualified electrician.
Your treadmill, like any other type of sophisticated
electronic equipment, can be seriously damaged by
sudden voltage changes in your home’s power.
Voltage surges, spikes, and noise interference can
result from weather conditions or from other appliances
being turned on or off. To decrease the possibility of
your treadmill being damaged, always use a surge
suppressor with your treadmill (see drawing 1 at
the right). To purchase a surge suppressor, see
your local PROFORM dealer or call the toll-free
telephone number on the front cover of this man-
ual and order part number 146148, or see your local
electronics store.
Grounding Pin
Grounded Outlet
Grounding Plug
2
Grounded Outlet Box
Adapter
Surge Suppressor
Use only a single-outlet surge suppressor that is
UL 1449 listed as a transient voltage surge sup-
pressor (TVSS). The surge suppressor must have a
UL suppressed voltage rating of 400 volts or less
and a minimum surge dissipation of 450 joules.
The surge suppressor must be electrically rated for
120 volts AC and 15 amps. There must be a moni-
toring light on the surge suppressor to indicate
whether it is functioning properly. Failure to use a
properly functioning surge suppressor could result
in damage to the control system of the treadmill. If
the control system is damaged, the walking belt
may change speed, accelerate or stop unexpect-
edly, which may result in a fall and serious injury.
Lug
Metal Screw
The temporary adapter should be used only until a
properly grounded outlet (drawing 1) can be installed
by a qualified electrician.
The green-colored rigid ear, lug, or the like extending
from the adapter must be connected to a permanent
ground such as a properly grounded outlet box cover.
Whenever the adapter is used it must be held in place
by a metal screw. Some 2-pole receptacle outlet box
covers are not grounded. Contact a qualified elec-
trician to determine if the outlet box cover is
grounded before using an adapter.
This product must be grounded. If it should malfunc-
tion or break down, grounding provides a path of least
resistance for electric current, reducing the risk of elec-
10
Download from Www.Somanuals.com. All Manuals Search And Download.
CONSOLE DIAGRAM
Key
Clip
FEATURES OF THE CONSOLE
programs to choose among. Note: The strength exer-
cises require the use of dumbbells and an inflatable
exercise ball (not included). To purchase dumbbells
or an exercise ball, call the toll-free telephone
number on the front cover of this manual.
The revolutionary treadmill console offers a selection
of features designed to make your workouts more
effective and enjoyable.
When you select the manual mode of the console, you
can change the speed and incline of the treadmill with
the touch of a button. As you exercise, the console will
display continuous exercise feedback. You can even
measure your heart rate using the handgrip pulse sen-
sor or the optional chest pulse sensor (see page 18 for
information about the optional chest pulse sensor).
In addition to the cross trainer programs, you can even
create your own custom workout programs and save
them in memory for future use.
To use the manual mode of the console, follow the
steps beginning on page 12. To use a cross trainer
program, see page 14. To create and use a custom
program, see pages 16 and 17.
The console also features nine interactive cross trainer
programs designed to help you to burn calories and
enhance your cardiovascular system while toning and
strengthening your muscles. These programs feature
the voice of a personal trainer to guide you through
your workouts. The cross trainer programs automati-
cally control the speed and incline of the treadmill and
prompt you to perform a variety of strength exercises
during your workout. There are three whole body,
three upper body, and three lower body cross trainer
Note: If there is a sheet of clear plastic on the face
of the console, remove the plastic. To prevent dam-
age to the walking platform, wear clean athletic
shoes while using the treadmill. The first time the
treadmill is used, observe the alignment of the
walking belt, and center the walking belt if neces-
sary (see page 21).
11
Download from Www.Somanuals.com. All Manuals Search And Download.
HOW TO TURN ON THE POWER
Speed increase and decrease buttons. Each time
a button is pressed, the speed setting will change
by 0.1 mph; if a button is held down, the speed
setting will change in increments of 0.5 mph. Note:
After the buttons are pressed, it may take a moment
for the walking belt to reach the selected speed set-
ting.
Plug in the power cord (see page 10).
1
Locate the reset/off
circuit breaker near
the power cord. Make
sure that the circuit
breaker is in the reset
position.
2
Reset
Position
If one of the numbered speed buttons is pressed,
the walking belt will gradually change speed until it
reaches the selected speed setting.
To stop the walking belt, press the Stop button.
The time will begin to flash in the display. To
restart the walking belt, press the Start button, the
Speed increase button, or one of the numbered
speed buttons.
Next, stand on the foot rails of the treadmill. Find
the clip attached to the key (see the drawing on
page 11) and slide the clip onto the waistband of
your clothes. Then, insert the key into the console.
After a moment, the display will light. Important:
In an emergency situation, the key can be
pulled from the console, causing the walking
belt to slow to a stop. Test the clip by carefully
taking a few steps backward; if the key is not
pulled from the console, adjust the position of
the clip.
3
Change the incline of the treadmill as desired.
4
5
To change the incline of
the treadmill, press the
Incline increase and de-
crease buttons or one of
the incline buttons num-
bered 0 to 10. Each time
the Incline increase or decrease button is
pressed, the incline will change by 0.5%. If one of
the numbered incline buttons is pressed, the
treadmill will adjust to the selected incline setting.
Note: After the buttons are pressed, it may take a
moment for the treadmill to reach the selected in-
cline setting.
HOW TO USE THE MANUAL MODE
Insert the key into the console.
1
See HOW TO TURN ON THE POWER above.
Select the manual mode.
2
Follow your progress with the display.
When the
key is in-
serted, the
manual
Note: The display features several different
background colors. To select a background
color, press the Display Color button repeat-
edly.
mode will be
selected. If a
program has
Track
When the
manual mode
is selected,
the display
been selected, reselect the manual mode by
pressing any of the four Programs buttons repeat-
edly until a track appears in the display.
will show a
track that
Track
Start the walking belt.
3
represents
1/4 mile. As you walk or run, indicators will appear
in succession around the track until the entire track
appears. The track will then disappear and the in-
dicators will again begin to appear in succession.
To start the walking belt, press the Start button,
the Speed increase button, or one of the speed
buttons numbered 1 to 10.
If the Start button or the
Speed increase button
is pressed, the walking
belt will begin to move
at 1 mph. As you exer-
cise, change the speed
of the walking belt as desired by pressing the
12
Download from Www.Somanuals.com. All Manuals Search And Download.
The left side of the dis-
play will show the
elapsed time, the dis-
tance that you have
Before using
the handgrip
pulse sensor,
remove the
sheets of
walked or run, and the
incline level of the tread-
clear plastic
from the
metal con-
tacts. In addi-
Contacts
mill. Note: When a cross trainer program is se-
lected, the display will show the time remaining in
the program instead of the elapsed time.
tion, make sure that your hands are clean.
The right side of the dis-
play will show the ap-
proximate number of
To measure your heart rate, stand on the foot
rails and hold the metal contacts on the
calories you have
burned while walking or
running, the speed of
the walking belt, and your pace in minutes per
mile. The right side of the display will also show
your heart rate when you use the handgrip pulse
sensor or the optional chest pulse sensor.
handrail—avoid moving your hands. When your
pulse is detected, one or two dashes will appear in
the right side of the display and then your heart
rate will be shown. For the most accurate heart
rate reading, continue to hold the contacts for
about 15 seconds.
Turn on the fan if desired.
7
8
Note: The console can display speed and dis-
tance in either miles or kilometers. To find out
which unit of measurement is selected or to
change the unit of measurement, see THE IN-
FORMATION MODE/DEMO MODE on page 18.
Note: For simplicity, all instructions in this sec-
tion refer to miles.
To turn on the fan, press the Fan button. To turn
on the fan at high speed, press the button a sec-
ond time. To turn off the fan, press the button a
third time. Note: If the fan is on when the walking
belt stops, the fan will automatically turn off after a
few minutes.
To reset the display, press the Stop button, re-
move the key, and then reinsert the key.
When you are finished exercising, remove the
key.
To see the total number
of miles that the walking
belt has moved since the
last reset, press the
odometer (ODOM.) but-
Step onto the foot rails, press the Stop button, and
adjust the incline of the treadmill to the lowest
setting. The incline must be at the lowest setting
when the treadmill is folded to the storage posi-
tion or the treadmill will be damaged. Next, re-
move the key from the console and put it in a se-
cure place. Note: If the display remains lit after
the key is removed, the console is in the
“demo” mode. See page 18 and turn off the
demo mode.
ton; the total number of
miles will appear in the matrix. To reset this num-
ber, hold down the odometer button for a few sec-
onds.
The number will appear in the display for a few
seconds.
When you are finished using the treadmill,
switch the reset/off circuit breaker to the “off”
position and unplug the power cord.
Measure your heart rate if desired.
6
Note: If you use the handgrip pulse sensor and
the optional chest pulse sensor at the same
time, the console will not display your heart
rate accurately.
13
Download from Www.Somanuals.com. All Manuals Search And Download.
The speed
setting for
the first seg-
ment will be
shown in the
flashing
HOW TO USE A CROSS TRAINER PROGRAM
Insert the key into the console.
1
Current Segment
See HOW TO TURN ON THE POWER on page
12.
Current
Segment column of the matrix. (The incline set-
tings are not shown in the matrix.) The speed set-
tings for the next several segments will be shown
in the columns to the right.
Select one of the nine cross trainer programs.
2
To select a
cross trainer
program,
press the
Upper Body
Programs
button, the
Lower Body
Programs
When only three seconds remain in the first seg-
ment of the program, both the Current Segment
column and the column to the right will flash. If the
speed and/or incline of the treadmill is about to
change, the personal trainer will alert you, and the
speed setting and/or the incline setting will flash in
the display.
button, or the Whole Body Programs button re-
peatedly until “P 1,” “P 2,” “P 3,” “P 4,” “P 5,” “P 6,”
“P 7,” “P 8,” or “P 9” appears in the display. When
a cross trainer program is selected, the program
time will appear in the display, the maximum in-
cline setting of the program and the maximum
speed setting of the program will flash in the dis-
play for a few seconds, and a profile of the speed
settings of the program will scroll across the matrix
in the display.
When the first segment is completed, all speed
settings will move one column to the left. The
speed setting for the second segment will then be
shown in the flashing Current Segment column
and the treadmill will automatically adjust to the
speed and incline settings for the second seg-
ment. Note: If all of the indicators in the Current
Segment column are lit, the speed settings may
move downward so that only the highest indicators
appear in the matrix.
Note: During the program, a personal trainer will
guide you through the workout. You can adjust the
volume or select an audio setting for your personal
trainer (see THE INFORMATION MODE on page
18).
If the speed or incline setting for the current seg-
ment is too high or too low, you can manually
override the setting by pressing the Speed and
Incline buttons. Every few times a Speed button is
pressed, an additional indicator will appear or dis-
appear in the Current Segment column; if any of
the columns to the right of the Current Segment
column have the same number of lit indicators as
the Current Segment column, an additional indica-
tor may appear or disappear in those columns as
well. Important: When the current segment of
the program ends, the treadmill will automati-
cally adjust to the speed and incline settings
for the next segment.
Press the Start button to start the program.
3
A moment after the button is pressed, the tread-
mill will automatically adjust to the first speed and
incline settings of the program. Hold the handrails
and begin walking.
Each program is divided into 25, 30, or 45 one-
minute segments. One speed setting and one in-
cline setting are programmed for most segments.
(Note: The same speed setting and/or incline set-
ting may be programmed for two or more consecu-
tive segments.) During other segments, the console
will prompt you to perform strength exercises.
To stop the program at any time, press the Stop
button. The time will begin to flash in the display.
To restart the program, press the Start button or
the Speed increase button. The walking belt will
begin to move at 1 mph. When the next segment
of the program begins, the treadmill will automati-
cally adjust to the speed and incline settings for
that segment.
14
Download from Www.Somanuals.com. All Manuals Search And Download.
Perform the first strength exercise when
prompted.
Continue the cross trainer program.
4
5
When you have performed the recommended
number of repetitions, the words PRESS START
will appear in the display. To continue the cross
trainer program, step onto the treadmill, slide the
clip back onto the waistband of your clothes,
and press the Start button. The treadmill will auto-
matically adjust to the speed and incline settings
for the next segment.
When the
first strength
exercise
segment be-
gins (only
one indica-
tor will flash
in the Current Segment column), the walking belt
will slow to a stop and the name of the first
strength exercise will appear in the display for a
few seconds.
The program will continue in this way until the last
segment ends. The walking belt will then slow to a
stop.
Next, the personal trainer will tell you the recom-
mended number of repetitions for the first strength
exercise.
Follow your progress with the display.
6
7
8
9
See step 5 on pages 12 and 13.
Measure your heart rate if desired.
Remove the clip from the waistband of your
clothes, step off the treadmill, and prepare to
begin the first strength exercise. The personal
trainer and the display will count the repetitions;
perform one repetition of the exercise on each
count. Exercise with a slow, steady motion; do not
perform more than one repetition for each count.
See step 6 on page 13.
Turn on the fan if desired.
See step 7 on page 13.
When you are finished exercising, remove the
key from the console.
Note: Refer to the accompanying exercise chart to
see the correct form for each exercise. When per-
forming lunges, alternate legs with each repetition.
When performing dumbbell rows, perform half the
repetitions with your right arm and half the repeti-
tions with your left arm. The strength exercises re-
quire the use of dumbbells and an inflatable exer-
cise ball (not included). To purchase dumbbells
or an exercise ball, call the toll-free telephone
number on the front cover of this manual.
See step 8 on page 13.
15
Download from Www.Somanuals.com. All Manuals Search And Download.
be shown in the flashing Current Segment column
of the matrix. (The incline settings are not shown
in the matrix.) To program a speed setting and an
incline setting for the first segment, simply adjust
the speed and incline of the treadmill as desired
by pressing the Speed and Incline buttons. Every
few times a Speed button is pressed, an addi-
tional indicator will appear or disappear in the
Current Segment column.
HOW TO CREATE A CUSTOM PROGRAM
Insert the key into the console.
1
See HOW TO TURN ON THE POWER on page
12.
Select one of the custom programs.
2
When the first segment of the program ends, the
current speed setting and the current incline set-
ting will be saved in memory. The three columns
of indicators will then move one column to the left,
and the speed setting for the second segment will
be shown in the flashing Current Segment column.
Program a speed setting and an incline setting for
the second segment as described above.
To select a
custom pro-
gram, press
the Custom
Programs
button once
or twice, until
“P10” or
“P11” ap-
pears in the display.
Continue programming speed and incline settings
for as many segments as desired; custom pro-
grams can have up to forty segments. When you
are finished with your workout, press the Stop but-
ton twice. The speed and incline settings that you
have programmed and the number of segments
that you have programmed will then be saved in
memory.
Note: If the custom program has not yet been
defined, only three columns of indicators will
scroll across the matrix. If more than three
columns of indicators appear, see HOW TO
USE A CUSTOM PROGRAM on page 17.
Press the Start button and program the desired
speed and incline settings.
3
When you are finished exercising, remove the
key from the console.
4
A moment after the button is pressed, the walking
belt will begin to move. Hold the handrails and
begin walking.
See step 8 on page 13.
See the ma-
trix in the
display.
Each cus-
tom program
is divided
into one-
Current Segment
minute segments. One speed setting and one in-
cline setting can be programmed for each seg-
ment. The speed setting for the first segment will
16
Download from Www.Somanuals.com. All Manuals Search And Download.
When the first segment is completed, all speed
settings will move one column to the left. The
speed setting for the second segment will then be
shown in the flashing Current Segment column
and the treadmill will automatically adjust to the
speed and incline settings for the second segment.
HOW TO USE A CUSTOM PROGRAM
Insert the key into the console.
1
See HOW TO TURN ON THE POWER on page
12.
The program will continue in this way until the
speed setting for the last segment is shown in the
Current Segment column and the last segment
ends. The walking belt will then slow to a stop.
Select one of the custom programs.
2
To select a custom program, press the Custom
Programs button once or twice, until “P10” or “P11”
appears in the display.
If desired, you can redefine the program while
using it. To change the speed or incline setting
for the current segment, simply press the Speed
or Incline buttons. When the current segment ends,
the new setting will be saved in memory. To in-
crease the length of the program, first wait until
the program is completed. Then, press the Start but-
ton and program speed and incline settings for as
many additional segments as desired. When you
have added as many segments as desired, press
the Stop button twice. To decrease the length of
the program, press the Stop button twice at any
time before the program is completed.
When a custom program is selected, the maxi-
mum speed setting of the program and the maxi-
mum incline setting of the program will flash in the
display for a few seconds. The display will also
show how long the program will last. A profile of
the speed settings of the program will scroll
across the matrix. Note: If only three columns of
indicators scroll across the matrix, see HOW
TO CREATE A CUSTOM PROGRAM on page
16.
Press the Start button to start the program.
3
To stop the program at any time, press the Stop
button. The time will begin to flash in the display.
To restart the program, press the Start button or
the Speed increase button. The walking belt will
begin to move at 1 mph. When the next segment
of the program begins, the treadmill will automati-
cally adjust to the speed and incline settings for the
next segment.
A moment after the button is pressed, the tread-
mill will automatically adjust to the first speed and
incline settings that you programmed previously.
Hold the handrails and begin walking.
Each custom program is divided into several one-
minute segments. One speed setting and one in-
cline setting are programmed for each segment.
Follow your progress with the displays.
See step 5 on pages 12 and 13.
Measure your heart rate if desired.
See step 6 on page 13.
4
5
6
7
The speed
setting for
the first seg-
ment will be
shown in the
flashing
Current
Segment column of the matrix. (The incline set-
tings are not shown in the matrix.) The speed set-
tings for the following segments will be shown in
the columns to the right.
Current Segment
Turn on the fan if desired.
See step 7 on page 13.
When you are finished exercising, remove the
key from the console.
When only three seconds remain in the first seg-
ment of the program, both the Current Segment
column and the column to the right will flash. If the
speed and/or incline of the treadmill is about to
change, the personal trainer will alert you, and the
speed setting and/or the incline setting will flash in
the display.
See step 8 on page 13.
17
Download from Www.Somanuals.com. All Manuals Search And Download.
THE INFORMATION MODE/DEMO MODE
IMPORTANT: If a “d” ap-
pears in the display, the con-
The console features an information mode that keeps
track of treadmill usage information. The information
mode also allows you to select miles or kilometers as
the unit of measurement, to select an audio trainer set-
ting, and to turn on and turn off the demo mode.
sole is in the “demo” mode.
This mode is intended to be
used only when a treadmill is
displayed in a store. When
the console is in the demo mode, the power cord can
be plugged in, the key can be removed from the con-
sole, and the indicators in the display will automatically
To select the information mode, hold down the Stop
button, insert the key into the console, and then release appear in a preset sequence; the buttons on the con-
the Stop button. When the information mode is se-
lected, the following information will appear in the dis-
play:
sole will not operate. If a “d” appears when the infor-
mation mode is selected, press the Speed decrease
button so that the “d” disappears.
The center of
the display will
To exit the information mode, remove the key from the
console.
show the total
number of hours
THE OPTIONAL CHEST PULSE SENSOR
that the tread-
mill has been
operated. The
lower part of the
display will
show total number of miles or kilometers that the walk-
ing belt has moved. In addition, an “E” for English miles
or an “M” for metric kilometers will appear in the lower
part of the display. To change the unit of measurement,
press the Speed increase button.
An optional chest pulse sensor offers hands-free oper-
ation as it tracks your heart rate during your workouts.
To purchase the optional chest pulse sensor, call
the toll-free telephone number on the front cover
of this manual.
The upper left part of the dis-
play will show the personal
trainer audio setting. If you
select “ON” as the audio set-
ting, the personal trainer will
guide you through your work-
outs and give detailed in-
structions. If you select the “OFF” setting, your per-
sonal trainer will simply guide you through your work-
outs. Press the Incline decrease button to change the
audio setting if desired.
You can adjust the volume
of the personal trainer
audio (0 through 5) by
pressing the Incline in-
crease button repeatedly.
The volume setting ap-
pears as the upper right digit in the display.
18
Download from Www.Somanuals.com. All Manuals Search And Download.
HOW TO FOLD AND MOVE THE TREADMILL
HOW TO FOLD THE TREADMILL FOR STORAGE
Before folding the treadmill, adjust the incline to the
lowest position. If this is not done, the treadmill may be-
come permanently damaged. Next, unplug the power cord.
CAUTION: You must be able to safely lift 45 pounds (20 kg)
to raise, lower, or move the treadmill.
Frame
1. Hold the metal frame firmly in the location shown by the
arrow at the right. CAUTION: To decrease the possibility
of injury, do not lift the frame by the plastic foot rails.
Make sure to bend your legs and keep your back straight.
As you raise the frame, make sure to lift with your legs
rather than with your back.
2. Raise the frame until the latch knob locks into the storage po-
sition. Make sure that the latch knob is locked in the stor-
age position.
Frame
To protect the floor or carpet from damage, place a mat
under the treadmill. Keep the treadmill out of direct sun-
light. Do not leave the treadmill in the storage position in
temperatures above 85° Fahrenheit.
Latch Knob
HOW TO MOVE THE TREADMILL
Before moving the treadmill, convert the treadmill to the storage
position as described above. Make sure that the latch knob is
locked in the storage position.
1. Hold the handrails and place one foot against one of the
wheels.
Handrail
2. Tilt the treadmill backward until it rolls freely on the front
wheels. Carefully move the treadmill to the desired location.
To reduce the risk of injury, use extreme caution while
moving the treadmill. Do not move the treadmill over an
uneven surface.
Wheel
3. Place one foot against one of the wheels, and carefully lower
the treadmill until it is resting in the storage position.
HOW TO LOWER THE TREADMILL FOR USE
1. Hold the upper end of the treadmill with your left hand. Pull the latch knob to the left and hold it. It may be nec-
essary to push the frame forward as you pull the knob to the left. Pivot the frame downward and release the
latch knob.
2. Hold the metal frame firmly with both hands, and lower it to the floor. CAUTION: To decrease the possibility
of injury, do not lower the frame by gripping only the plastic foot rails. Do not drop the frame to the floor.
Make sure to bend your legs and keep your back straight.
19
Download from Www.Somanuals.com. All Manuals Search And Download.
TROUBLESHOOTING
Most treadmill problems can be solved by following the steps below. Find the symptom that applies, and
follow the steps listed. If you need further assistance, please call the toll-free telephone number on the
front cover of this manual.
PROBLEM: The power does not turn on
SOLUTION: a. Make sure that the power cord is plugged into a surge suppressor, and that the surge suppressor
is plugged into a properly grounded outlet (see page 10). Use only a single-outlet surge suppres-
sor that meets all of the specifications described on page 10. Important: The treadmill is not com-
patible with GFCI-equipped outlets.
b. After the power cord has been plugged in, make sure that the key is inserted into the console.
c. Check the reset/off circuit breaker located on the
c
treadmill frame near the power cord. If the switch
protrudes as shown, the circuit breaker has
tripped. To reset the circuit breaker, wait for five
minutes, and then press the switch back in.
Reset
Tripped
PROBLEM: The power turns off during use
SOLUTION: a. Check the reset/off circuit breaker (see the drawing above). If the circuit breaker has tripped, wait
for five minutes and then press the switch back in.
b. Make sure that the power cord is plugged in. If the power cord is plugged in, unplug it, wait for
five minutes, and then plug it back in.
c. Remove the key from the console. Reinsert the key into the console.
d. If the treadmill still will not run, please see the front cover of this manual.
PROBLEM: The display of the console does not function properly
SOLUTION: a. Remove the key from the console and UNPLUG THE
a
POWER CORD. Next, carefully lower the Uprights
(84). Remove the two indicated 3/4” Screws (2). Note:
A phillips screwdriver with a shaft at least 8” long is re-
quired.
2
84
7
Raise the Uprights (84) to the vertical position.
Remove the three Hood Screws (7) from the Hood
(41), and carefully pivot the Hood off.
84
41
20
Download from Www.Somanuals.com. All Manuals Search And Download.
Locate the Reed Switch (63) and the Magnet (46) on
the left side of the Front Roller (47). Turn the Front
Roller until the Magnet is aligned with the Reed
Switch. Make sure that the gap between the Magnet
and the Reed Switch is about 1/8". If necessary,
move the Reed Switch slightly using a slotted screw-
driver. Reattach the Hood (not shown), making sure
that the Screws (not shown) are inserted into the same
holes from which they were removed. Then, run the
treadmill for a few minutes to check for a correct speed
reading.
Top
View
47
46
63
1/8"
PROBLEM: The walking belt slows when walked on
SOLUTION: a. Use only a single-outlet surge suppressor that meets all the specifications described on page 10.
b. If the walking belt is overtightened, treadmill perfor-
b
mance may decrease and the walking belt may be-
come damaged. Remove the key and UNPLUG THE
POWER CORD. Using the hex key, turn both rear
roller bolts counterclockwise, 1/4 of a turn. When the
walking belt is properly tightened, you should be able
to lift each edge of the walking belt 2 to 3 inches
above the walking platform. Be careful to keep the
walking belt centered. Then, plug in the power cord,
insert the key, and run the treadmill for a few minutes.
Repeat until the walking belt is properly tightened.
2"–3"
Rear Roller Bolts
c. If the walking belt still slows when walked on, please see the front cover of this manual.
PROBLEM: The walking belt is off-center or slips when walked on
SOLUTION: a. If the walking belt is off-center, first remove the key
a
and UNPLUG THE POWER CORD. If the walking
belt has shifted to the left, use the hex key to turn
the left rear roller bolt clockwise 1/2 of a turn; if the
walking belt has shifted to the right, turn the left
bolt counterclockwise 1/2 of a turn. Be careful not to
overtighten the walking belt. Then, plug in the power
cord, insert the key, and run the treadmill for a few
minutes. Repeat until the walking belt is centered.
b. If the walking belt slips when walked on, first re-
b
move the key and UNPLUG THE POWER CORD.
Using the hex key, turn both rear roller bolts clock-
wise, 1/4 of a turn. When the walking belt is correctly
tightened, you should be able to lift each edge of the
walking belt 2 to 3 inches above the walking platform.
Be careful to keep the walking belt centered. Then,
plug in the power cord, insert the key, and carefully
walk on the treadmill for a few minutes. Repeat until
the walking belt is properly tightened.
PROBLEM: The incline of the treadmill does not change correctly
SOLUTION: a. With the key in the console, press one of the Incline buttons. While the incline is changing, re-
move the key. After a few seconds, reinsert the key. The treadmill will automatically rise to the
maximum incline level and then return to the minimum level. This will recalibrate the incline system.
21
Download from Www.Somanuals.com. All Manuals Search And Download.
CONDITIONING GUIDELINES
ergy. Only after the first few minutes does your body
begin to use stored fat calories for energy. If your goal
is to burn fat, adjust the speed and incline of the tread-
mill until your heart rate is near the lowest number in
your training zone.
WARNING:
Before beginning this
or any exercise program, consult your physi-
cian. This is especially important for individu-
als over the age of 35 or individuals with pre-
existing health problems.
For maximum fat burning, adjust the speed and incline
of the treadmill until your heart rate is near the middle
number in your training zone.
The pulse sensor is not a medical device.
Various factors, including your movement,
may affect the accuracy of heart rate readings.
The sensor is intended only as an exercise aid
in determining heart rate trends in general.
Aerobic Exercise
If your goal is to strengthen your cardiovascular sys-
tem, your exercise must be “aerobic.” Aerobic exercise
is activity that requires large amounts of oxygen for
prolonged periods of time. This increases the demand
on the heart to pump blood to the muscles, and on the
lungs to oxygenate the blood. For aerobic exercise,
adjust the speed and incline of the treadmill until your
heart rate is near the highest number in your training
zone.
The following guidelines will help you to plan your ex-
ercise program. For more detailed exercise informa-
tion, obtain a reputable book or consult your physician.
EXERCISE INTENSITY
Whether your goal is to burn fat or to strengthen your
cardiovascular system, the key to achieving the
desired results is to exercise with the proper intensity.
The proper intensity level can be found by using your
heart rate as a guide. The chart below shows recom-
mended heart rates for fat burning and aerobic exercise.
WORKOUT GUIDELINES
Each workout should include the following three parts:
A Warm-up—Start each workout with 5 to 10 minutes
of stretching and light exercise. A proper warm-up in-
creases your body temperature, heart rate and circula-
tion in preparation for exercise.
Training Zone Exercise—After warming up, increase
the intensity of your exercise until your heart rate is in
your training zone for 20 to 60 minutes. (During the
first few weeks of your exercise program, do not keep
your heart rate in your training zone for longer than 20
minutes.) Breathe regularly and deeply as you exer-
cise—never hold your breath.
To find the proper heart rate for you, first find your age
near the bottom of the chart (ages are rounded off to
the nearest ten years). Next, find the three numbers
above your age. The three numbers define your “train-
ing zone.” The lower two numbers are recommended
heart rates for fat burning; the higher number is the
recommended heart rate for aerobic exercise.
A Cool-down—Finish each workout with 5 to 10 min-
utes of stretching to cool down. This will increase the
flexibility of your muscles and will help prevent post-
exercise problems.
EXERCISE FREQUENCY
Fat Burning
To maintain or improve your condition, complete three
workouts each week, with at least one day of rest be-
tween workouts. After a few months, you may com-
plete up to five workouts each week if desired. The key
to success is to make exercise a regular and enjoyable
part of your everyday life.
To burn fat effectively, you must exercise at a relatively
low intensity level for a sustained period of time.
During the first few minutes of exercise, your body
uses easily accessible carbohydrate calories for en-
22
Download from Www.Somanuals.com. All Manuals Search And Download.
PART LIST—Model No. PFTL79506.0
R1006A
To locate the parts listed below, see the EXPLODED DRAWING on pages 24 to 27.
Key
Key
Key
No. Qty. Description
No. Qty. Description
No. Qty. Description
1
2
3
4
2
8
41
1
Foot Rail Cover
3/4" Screw
Screw
40
41
42
1
1
1
Filter Wire
Hood
Front Roller
Bushing
Lift Frame
Front Endcap
Front Roller Bolt
Magnet
Front Roller
Walking Belt
Walking Platform
Latch Shock
Bolt, Upper
Rear Roller
Left Rear Endcap
Rear Roller Bolt
Right Rear Endcap
Hex Key
Incline Stop
Bracket
Base Ground Wire
Frame
Belly Pan
U-nut
Reed Switch Clip
Handrail Endcap
Reed Switch
Handrail Bolt
Base Leg Bolt
Hood Cover
Washer
Extension Leg Nut
Caution Decal
Warning Decal
Platform Nut
Cable Tie
Cotter Pin
Belly Pan Clip
Tie Clamp
Releasable Tie
Access Door
Wire Harness
Extension Leg
Endcap
81
82
83
84
85
86
87
88
89
90
2
4
8
1
1
1
2
1
2
2
Wheel Pin
Base Pad
1" Tek Screw
Upright
Console Base
Incline Motor Pin
Hair Pin Cotter Pin
Incline Motor
Extension Leg
Rear Roller
Reset/Off
Circuit Breaker
Foot Rail Screw
Isolator
Hood Screw
Star Washer
Platform Bolt, Back
Platform Bolt, Front
Belt Guide Screw
Belt Guide
Power Cord
Grommet
Front Endcap
Screw
Frame Pivot Bolt
Left Foot Rail
Right Foot Rail
Isolator Bracket
Cover
Isolator Bolt
Handrail
Rear Roller
Washer
3/4” Tek Screw
Rear Roller Lock
Washer
Motor Bolt
Transformer
Motor Belt
Drive Motor
Frame Spacer
Latch Shock
Latch Shock Nut
Lift Frame Bolt
Lock Nut
Ground Screw
Console
Fan Screw
43
44
45
46
47
48
49
50
1
2
1
1
1
1
1
1
5
6
7
8
9
10
11
12
13
10
2
5
8
2
2
4
2
1
Bracket
Static Decal
91
92
93
94
95
1
1
1
1
1
Idler Arm Pivot Bolt
Optic Disk
Photo Switch Nut
Photo Switch
Star Washer
Photo Switch
Photo Switch Bolt
Dumbbell
Idler Arm Spacer
Wire Tie
Roller Ground Wire
Photo Switch Wire
Idler Arm Spring
Pulley Bolt
Idler Arm
Idler Arm Pulley
Idler Arm
51
52
53
54
55
56
1
1
2
1
1
1
14
2
15
16
17
18
2
1
1
2
96
97
98
1
1
2
1
4
1
1
1
1
1
1
1
57
58
59
60
61
62
63
64
65
66
1
1
1
4
1
2
1
4
4
4
99
100
101
102
103
104
105
106
107
19
20
21
2
1
2
22
23
4
2
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
2
1
1
1
2
1
2
2
6
16
1
2
1
1
1
1
Pulley Nut
Idler Arm Pivot Nut
Idler Arm
108
109
1
1
67
68
69
70
71
72
73
74
75
76
77
78
4
2
1
4
9
1
3
2
1
1
1
2
Pivot Washer
Thin Base Pad
Latch Catch
Front Isolator
4" Blue Wire, 2F
10" Red Wire, M/F
12" Blue Wire, 2F
8" Black Wire, M/F
12" Blue Wire, M/F
User’s Manual
110
111
112
#
#
#
#
#
#
2
1
2
1
1
1
1
1
1
Power Cord
Console Fan
Controller
Latch Shock
Bolt, Lower
“#” indicates a non-illustrated part.
Specifications are subject to
change without notice.
79
80
1
2
Key/Clip
Front Wheel
23
Download from Www.Somanuals.com. All Manuals Search And Download.
EXPLODED DRAWING—Model No. PFTL79506.0
R1006A
24
Download from Www.Somanuals.com. All Manuals Search And Download.
Part 2 of 4
41
7
114
7
7
66
66
2
2
66
33
66
2
2
73
2
38
2
73
103
73
2
26
59
2
27
4
2
2
92
40
99
36
103
109
104
105
24
108
13
106
33
107
43
25
28
32
42
61
45
63
32
28
25
Download from Www.Somanuals.com. All Manuals Search And Download.
Part 3 of 4
8
3
64
8
3
20
3
8
64
3
60
62
3
8
3
3
3
77
3
84
62
60
44
14
32
31
33
57
65
32
82
22
68
31
77
82
67
78
22
33
65
14
44
89
86
87
82
22
81
88
110
22
89
72
68
80
94
95
96
82
22
102
93
67
87
56
97
81
110
22
80
78
26
Download from Www.Somanuals.com. All Manuals Search And Download.
Part 4 of 4
37
35
35
34
79
33
85
3
3
91
76
100
3
3
98
71
75
33
74
27
Download from Www.Somanuals.com. All Manuals Search And Download.
ORDERING REPLACEMENT PARTS
To order replacement parts, see the front cover of this manual. To help us assist you, please be prepared to give
the following information:
• the MODEL NUMBER of the product (PFTL79506.0)
• the NAME of the product (PROFORM 755 CROSSTRAINER treadmill)
• the SERIAL NUMBER of the product (see the front cover of this manual)
• the KEY NUMBER and DESCRIPTION of the part(s) (see pages 23 to 27)
LIMITED WARRANTY
ICON Health & Fitness, Inc. (ICON) warrants this product to be free from defects in workmanship and
material under normal use and service conditions. The drive motor is warranted for twelve (12) years
after the date of purchase. Parts and labor are warranted for ninety (90) days after the date of purchase.
This warranty extends only to the original purchaser. ICON's obligation under this warranty is limited to
replacing or repairing, at ICON's option, the product through one of its authorized service centers. All re-
pairs for which warranty claims are made must be pre-authorized by ICON. If the product is shipped to a
service center, freight charges to and from the service center will be the customer’s responsibility. For in-
home service, the customer will be responsible for a minimal trip charge. This warranty does not extend
to any product or damage to a product caused by or attributable to freight damage, abuse, misuse, im-
proper or abnormal usage or repairs not provided by an ICON authorized service center; products used
for commercial or rental purposes; or products used as store display models. No other warranty beyond
that specifically set forth above is authorized by ICON.
ICON is not responsible or liable for indirect, special or consequential damages arising out of or in con-
nection with the use or performance of the product or damages with respect to any economic loss, loss
of property, loss of revenues or profits, loss of enjoyment or use, costs of removal or installation or other
consequential damages of whatsoever nature. Some states do not allow the exclusion or limitation of in-
cidental or consequential damages. Accordingly, the above limitation may not apply to you.
The warranty extended hereunder is in lieu of any and all other warranties and any implied warranties of
merchantability or fitness for a particular purpose is limited in its scope and duration to the terms set
forth herein. Some states do not allow limitations on how long an implied warranty lasts. Accordingly, the
above limitation may not apply to you.
This warranty gives you specific legal rights. You may also have other rights which vary from state to state.
ICON HEALTH & FITNESS, INC., 1500 S. 1000 W., LOGAN, UT 84321-9813
Part No. 239906 R1006A
Printed in USA © 2006 ICON IP, Inc.
Download from Www.Somanuals.com. All Manuals Search And Download.
|