Model No. PFTL71330
Serial No.
Write the serial number in the space
above for future reference.
USER'S MANUAL
Serial Number
Decal
QUESTIONS?
If you have questions, or if there
are missing parts, we will guar-
antee complete satisfaction
through direct assistance from
our factory.
TO AVOID DELAYS, PLEASE
CALL DIRECT TO OUR TOLL-
FREE CUSTOMER HOT LINE.
The trained technicians on our
customer hot line will provide
immediate assistance, free of
charge.
CUSTOMER HOT LINE:
1-800-999-3756
Mon.–Fri., 6 a.m.–6 p.m. MST
CAUTION
Read all precautions and instruc-
tions in this manual before using
this equipment. Save this manual
for future reference.
Visit our website at
new products, prizes,
fitness tips, and much more!
Download from Www.Somanuals.com. All Manuals Search And Download.
IMPORTANT PRECAUTIONS
WARNING:
To reduce the risk of burns, fire, electric shock, or injury to persons, read the
following important precautions and information before operating the treadmill.
1. It is the responsibility of the owner to ensure
that all users of this treadmill are adequately
informed of all warnings and precautions.
tem is damaged, the walking belt may change
speed or stop unexpectedly, which may result
in a fall and serious injury.
2. Use the treadmill only as described.
12. Keep the power cord and the surge suppres-
sor away from heated surfaces.
3. Place the treadmill on a level surface, with at
least eight feet of clearance behind it and two
feet on each side. Do not place the treadmill
on any surface that blocks air openings. To
protect the floor or carpet from damage,
place a mat under the treadmill.
13. Never move the walking belt while the power
is turned off. Do not operate the treadmill if
the power cord or plug is damaged, or if the
treadmill is not working properly. (See
BEFORE YOU BEGIN on page 5 if the tread-
mill is not working properly.)
4. Keep the treadmill indoors, away from mois-
ture and dust. Do not put the treadmill in a
garage or covered patio, or near water.
14. Never start the treadmill while you are stand-
ing on the walking belt. Always hold the
handrails while using the treadmill.
5. Do not operate the treadmill where aerosol
products are used or where oxygen is being
administered.
15. The treadmill is capable of high speeds.
Adjust the speed in small increments to avoid
sudden jumps in speed.
6. Keep children under the age of 12 and pets
away from the treadmill at all times.
16. Do not use the optional hand weights at
speeds faster than walking speeds. Using hand
weights and not holding the handrails may
compromise your ability to maintain your bal-
ance. Exercises using hand weights should be
attempted only by experienced users.
7. The treadmill should not be used by persons
weighing more than 275 pounds. Never allow
more than one person on the treadmill at a time.
8. Wear appropriate exercise clothing when
using the treadmill. Do not wear loose cloth-
ing that could become caught in the treadmill.
Athletic support clothes are recommended
for both men and women. Always wear ath-
letic shoes. Never use the treadmill with bare
feet, wearing only stockings, or in sandals.
17. The pulse sensor is not a medical device.
Various factors, including the user's move-
ment, may affect the accuracy of heart rate
readings. The pulse sensor is intended only
as an exercise aid in determining heart rate
trends in general.
9. When connecting the power cord (see page 7),
plug the power cord into a surge suppressor
(not included) and plug the surge suppressor
into a grounded circuit capable of carrying 15
or more amps. No other appliance should be on
the same circuit. Do not use an extension cord.
18. Never leave the treadmill unattended while it
is running. Always remove the key, unplug
the power cord, and move the on/off switch to
the off position when the treadmill is not in
use. (See the drawing on page 5 for the loca-
tion of the on/off switch.)
10. Use only a single-outlet surge suppressor that
meets all of the specifications described on
page 7. To purchase a surge suppressor, see
your local PROFORM 725i dealer or call 1-800-
806-3651 and order part number 146148.
19. Do not attempt to raise, lower, or move the
treadmill until it is properly assembled. (See
ASSEMBLY on page 6, and HOW TO FOLD
AND MOVE THE TREADMILL on page 21.)
You must be able to safely lift 45 pounds (20
kg) to raise, lower, or move the treadmill.
11. Failure to use a properly functioning surge
suppressor could result in damage to the con-
trol system of the treadmill. If the control sys-
20. When folding or moving the treadmill, make
sure that the storage latch is fully closed.
3
Download from Www.Somanuals.com. All Manuals Search And Download.
21. When using iFIT.com CDs and videos, an
electronic “chirping” sound will alert you
when the speed and/or incline of the treadmill
is about to change. Always listen for the
“chirp” and be prepared for speed and/or in-
cline changes. In some instances, the speed
and/or incline may change before the per-
sonal trainer describes the change.
24. Inspect and properly tighten all parts of the
treadmill every three months.
25. Never drop or insert any object into any open-
ing.
26.
DANGER:
Always unplug the power
cord immediately after use, before cleaning
the treadmill, and before performing the main-
tenance and adjustment procedures de-
scribed in this manual. Never remove the
motor hood unless instructed to do so by an
authorized service representative. Servicing
other than the procedures in this manual
should be performed by an authorized service
representative only.
22. When using iFIT.com CDs and videos, you can
manually override the speed and incline set-
tings at any time by pressing the speed and in-
cline buttons. However, when the next “chirp”
is heard, the speed and/or incline will change
to the next settings of the CD or video program.
23. Always remove iFIT.com CDs and videos from
your CD player or VCR when you are not
using them.
27. The treadmill is intended for in-home use
only. Do not use the treadmill in any
commercial, rental, or institutional setting.
WARNING:
Before beginning this or any exercise program, consult your physician. This
is especially important for persons over the age of 35 or persons with pre-existing health problems.
Read all instructions before using. ICON assumes no responsibility for personal injury or property
damage sustained by or through the use of this product.
SAVE THESE INSTRUCTIONS
The decals shown below have been placed on your treadmill. If a decal is missing or illegible, please call
our Customer Service Department toll-free at 1-800-999-3756 to order a free replacement decal. Apply the
decal in the location shown. Note: The long decal is shown at 38% of actual size.
4
Download from Www.Somanuals.com. All Manuals Search And Download.
BEFORE YOU BEGIN
Congratulations for purchasing the PROFORM® 725i
treadmill. The 725i offers an impressive array of fea-
tures to help you achieve your fitness goals in the con-
venience of your home. From the advanced console to
the cushioned walking platform, the 725i is designed to
make each workout more effective and enjoyable. And
when you’re not exercising, the 725i can be folded
away, taking less than half the floor space of conven-
tional treadmills.
please call our Customer Service Department toll-free
at 1-800-999-3756, Monday through Friday, 6 a.m.
until 6 p.m. Mountain Time (excluding holidays). To
help us assist you, please note the product model
number and serial number before calling. The model
number is PFTL71330. The serial number can be
found on a decal attached to the treadmill (see the
front cover of this manual for the location).
Before reading further, please familiarize yourself with
the parts that are labeled in the drawing below.
For your benefit, read this manual carefully before
using the treadmill. If you have additional questions,
Hand Weight Holder*
Chest Pulse Sensor Holder*
Water Bottle Holder†
Book Holder
Console
Latch Knob
Handrail
Key/Clip
On/Off Switch
Circuit Breaker
Walking Belt
Foot Rail
Power Cord
Cushioned Walking Platform
*See page 20 for information about the op-
tional chest pulse sensor and hand weights
Rear Roller
Adjustment Bolts
†No water bottle is included
5
Download from Www.Somanuals.com. All Manuals Search And Download.
ASSEMBLY
Assembly requires two people. Place the treadmill in a cleared area and remove all packing materials. Do not
dispose of the packing materials until the treadmill is assembled. No tools are required.
Note: The underside of the treadmill walking belt is coated with high-performance lubricant. During shipping, a
small amount of lubricant may be transferred to the top of the walking belt, the sides of the walking platform, or
the shipping carton. This does not affect treadmill performance. If there is lubricant on top of the walking belt or
on the sides of the walking platform, wipe off the lubricant with a soft cloth and a mild, non-abrasive cleaner.
1. With the help of a second person, carefully raise the
1
Uprights (65) until the Wheels (77) are resting on the floor
as shown.
65
77
2. Remove the Latch Knob (67) from the Latch Pin (72).
2
Make sure that the Latch Pin Collar (70) and the Spring
67
(69) are on the Latch Pin. (Note: If there are two Latch Pin
Collars, there should be one on each side of the Spring.)
Insert the Latch Pin through the Left Foam Grip (62), and
tighten the Latch Knob onto it.
62
After assembly is completed, pull the Left Foam Grip (62)
in the direction shown until the Latch Pin (72) slides
freely.
70
72
69
3. Make sure that all parts are tightened before you use the treadmill. Place a mat beneath the treadmill
to protect the floor or carpet. For your benefit, we recommend that you familiarize yourself with the
TROUBLESHOOTING AND MAINTENANCE section on pages 23 and 24.
6
Download from Www.Somanuals.com. All Manuals Search And Download.
TREADMILL OPERATION
THE PERFORMANT LUBETM WALKING BELT
an equipment-grounding conductor and a grounding
plug. Plug the power cord into a surge suppressor,
and plug the surge suppressor into an appropriate
outlet that is properly installed and grounded in
accordance with all local codes and ordinances.
Important: The treadmill is not compatible with
GFCI-equipped outlets.
Your treadmill features a walking belt coated with
PERFORMANT LUBETM, a high-performance lubricant.
IMPORTANT: Never apply silicone spray or other
substances to the walking belt or the walking plat-
form. Such substances will deteriorate the walking
belt and cause excessive wear.
This product is for use on a nominal 120-volt circuit,
and has a grounding plug that looks like the plug illus-
trated in drawing 1 below. A temporary adapter that
looks like the adapter illustrated in drawing 2 may be
used to connect the surge suppressor to a 2-pole
receptacle as shown in drawing 2 if a properly
grounded outlet is not available.
HOW TO PLUG IN THE POWER CORD
DANGER:
Improper connection
of the equipment-grounding conductor can
result in an increased risk of electric shock.
Check with a qualified electrician or service-
man if you are in doubt as to whether the
product is properly grounded. Do not modify
the plug provided with the product—if it will
not fit the outlet, have a proper outlet
1
Grounded Outlet Box
Surge Suppressor
Grounding Pin
installed by a qualified electrician.
Your treadmill, like any other type of sophisticated
electronic equipment, can be seriously damaged by
sudden voltage changes in your home’s power.
Voltage surges, spikes, and noise interference can
result from weather conditions or from other appli-
ances being turned on or off. To decrease the pos-
sibility of your treadmill being damaged, always
use a surge suppressor with your treadmill (see
drawing 1 at the right). To purchase a surge sup-
pressor, see your local PROFORM dealer or call 1-
800-806-3651 and order part number 146148.
Grounding Pin
Grounded Outlet
Grounding Plug
2
Grounded Outlet Box
Adapter
Surge Suppressor
Use only a single-outlet surge suppressor that is
UL 1449 listed as a transient voltage surge sup-
pressor (TVSS). The surge suppressor must have a
UL suppressed voltage rating of 400 volts or less
and a minimum surge dissipation of 450 joules.
The surge suppressor must be electrically rated
for 120 volts AC and 15 amps. There must be a
monitoring light on the surge suppressor to indi-
cate whether it is functioning properly. Failure to
use a properly functioning surge suppressor could
result in damage to the control system of the
treadmill. If the control system is damaged, the
walking belt may change speed or stop unexpect-
edly, which may result in a fall and serious injury.
Lug
Metal Screw
The temporary adapter should be used only until a
properly grounded outlet (drawing 1) can be installed
by a qualified electrician.
The green-colored rigid ear, lug, or the like extending
from the adapter must be connected to a permanent
ground such as a properly grounded outlet box cover.
Whenever the adapter is used it must be held in place
by a metal screw. Some 2-pole receptacle outlet box
covers are not grounded. Contact a qualified elec-
trician to determine if the outlet box cover is
grounded before using an adapter.
This product must be grounded. If it should malfunc-
tion or break down, grounding provides a path of least
resistance for electric current to reduce the risk of elec-
tric shock. This product is equipped with a cord having
7
Download from Www.Somanuals.com. All Manuals Search And Download.
DIAGRAM OF THE CONSOLE
K
L
Q
P
M
C
G
B
N
O
R
S
A
U
D E
F
H
T
Note: If there is a thin
sheet of clear plastic
on the face of the
console, remove it.
J
I
FEATURES OF THE CONSOLE
ing a personal trainer in your home. Using the included
audio cable, you can connect the treadmill to your
home stereo, portable stereo, computer, or VCR and
play special iFIT.com CD and video programs
The treadmill console offers an impressive selection of
features to help you get the most from your exercise.
(iFIT.com CDs and videocassettes are available sepa-
rately). iFIT.com CD and video programs automatically
control the speed and incline of the treadmill as a per-
sonal trainer coaches you through every step of your
workout. High-energy music provides added motivation.
To purchase iFIT.com CDs or videocassettes, call
toll-free 1-800-735-0768.
When the console is in the manual mode, the speed
and incline of the treadmill can be changed with the
touch of a button. As you exercise, the four displays
will show your workout time, the number of calories
you have burned, the distance you have walked, the
incline level of the treadmill, and the speed of the walk-
ing belt. The console will also show your heart rate
when you use the handgrip pulse sensor or the op-
tional chest pulse sensor (see page 20).
With the treadmill connected to your computer, you
cess programs directly from the internet. Additional op-
tions are soon to be available. See www.iFIT.com for
more information.
The console also offers four preset workout programs.
Each program automatically controls the speed and
incline of the treadmill as it guides you through an ef-
fective workout; the optional hand weights can be used
for upper body exercise as well (see page 20). Two
pulse programs are also offered. Each program auto-
matically adjusts the speed and incline of the treadmill
to keep your heart rate within a preset range during
your workout.
To use the manual mode of the console, follow the
steps beginning on page 10. To use preset programs,
see page 12. To use pulse programs, see page 13. To
use iFIT.com CD or video programs, see page 17.
To use iFIT.com programs directly from our Web
site, see page 19.
In addition, the console features new iFIT.com interac-
tive technology. Having iFIT.com technology is like hav-
8
Download from Www.Somanuals.com. All Manuals Search And Download.
DESCRIPTION OF THE CONSOLE
M. Pulse/Calories display—This display shows the
approximate number of calories you have burned.
When the handgrip pulse sensor is used, the display
will show your heart rate. If the optional chest pulse
sensor is worn, the display will show your heart rate
and the number of calories you have burned, alter-
nating between one number and the other every
seven seconds.
Refer to the drawing on page 8 to identify the features
described below.
A. Water bottle holder—This convenient holder keeps
your water bottle handy during your workouts.
B. Hand weight holder—These compartments hold the
optional hand weights.
N. Distance/Incline display—This display shows the
distance you have walked and the incline level of
the treadmill. The display will alternate between one
number and the other every seven seconds. Note:
Each time the Incline buttons are pressed, the dis-
play will change to show the incline setting.
C. Book holder—This area is designed to hold a book
or magazine.
D. Incline buttons—These buttons control the incline of
the treadmill. Each time a button is pressed, the
incline will change by 0.5%.
O. Speed display—This display shows the speed of
the walking belt.
E. Speed buttons—These buttons control the speed of
the walking belt. Each time a button is pressed, the
speed will change by 0.1 mph; if a button is held
down, the speed will change in increments of 0.5
mph. The speed range is 0.5 mph to 10 mph.
P. Enter button and + and – buttons—These buttons
are used to enter your age when pulse programs
are used.
Q. Program display—When the manual mode or the
iFIT.com mode is selected, this display will show
your progress on an LED track. When a preset
program or a pulse program is selected, the display
will show the settings for the program.
F. Start button—This button is used to start the walking
belt.
G. OneTouch Speed buttons—These buttons allow
you to quickly select speed settings.
R. Select Workout button—This button is used to select
the manual mode, the preset programs, and the
pulse programs. Note: If the walking belt is moving
when the Select Workout button is pressed, the
walking belt will slow to a stop, the displays will be
reset, and a new program or the manual mode will
be selected.
H. Stop button—This button is used to stop the walking
belt.
I. Waistband clip—This clip is designed to be worn on
the waistband of your clothes. If the key is pulled
from the console, the walking belt will automatically
stop.
S. IFIT.com button—This button is used to select the
iFIT.com mode.
J. Key—This key turns the console on and off.
K. Time/Segment Time display—When the manual
mode or the iFIT.com mode is selected, this display
will show the elapsed time. When a preset program
or a pulse program is selected, the display will show
both the time remaining in the program and the time
remaining in the current segment of the program.
The display will alternate between one number and
the other every seven seconds.
T. Mode indicators—These indicators show whether
the manual mode, a preset program, a pulse pro-
gram, or the iFIT.com mode is selected.
U. Program profiles—These profiles show how the
speed and incline of the treadmill will change during
preset programs and how the target heart rate will
change during pulse programs.
L. Cross Training indicator—During the two cross
training programs, this indicator will periodically
flash. The optional hand weights can be used while
the indicator is flashing to add upper body exercise
to your workouts.
Note: The console can display exercise feedback
in either miles or kilometers (see SPEED DISPLAY
on page 11). For simplicity, all instructions in this
section refer to miles.
9
Download from Www.Somanuals.com. All Manuals Search And Download.
HOW TO USE THE MANUAL MODE
WARNING:
To reduce the risk of
serious injury, read the following precautions
before operating the console.
Insert the key into the console.
1
• Do not stand on the walking belt when turn-
ing on the power or starting the walking belt.
See HOW TO TURN ON THE POWER at the left.
Select the manual mode.
2
• Always wear the clip (see “I”on page 8) on
the waistband of your clothes while you are
using the treadmill. If the key is pulled from
the console, the walking belt will stop.
When the key is in-
serted, the manual
Manual Indicator
mode will be selected
and the manual indica-
tor will light. If a program
is selected, press the
Select Workout button
repeatedly to select the
manual mode.
• The treadmill is capable of high speeds.
Adjust the speed in small increments.
• To reduce the risk of electric shock, keep
liquids away from the console and place only
a sealed water bottle in the console.
Press the Start button or the Speed + button to
start the walking belt.
3
HOW TO TURN ON THE POWER
A moment after the button is pressed, the walking
belt will begin to move at 1 mph. Hold the hand-
rails and begin walking.
Plug in the power cord (see HOW TO PLUG IN
THE POWER CORD on page 7).
1
Locate the on/off
switch on the front of
the treadmill near the
power cord. Move
the on/off switch to
the on position.
As you exercise, adjust
2
the speed of the walking
belt as desired by press-
ing the Speed buttons or
the OneTouch Speed
On
Position
buttons. Note: After the
buttons are pressed, it
Stand on the foot
may take a moment for the walking belt to reach
the selected speed setting.
3
rails of the treadmill.
Find the clip attached
to the key and slide
the clip fully onto the
waistband of your
To stop the walking belt, press the Stop button.
The displays will pause and the Time/Segment
Time display will begin to flash. To restart the
walking belt, press the Start button or the Speed +
button. To stop the walking belt and reset the dis-
plays, press the Stop button, remove the key, and
then reinsert the key.
clothes. Next, insert
the key into the console. After a moment, the
displays, the LED track, and various indicators will
light. Test the clip by carefully taking a few
steps backward until the key is pulled from the
console. If the key is not pulled from the con-
sole, adjust the position of the clip as needed.
Then, reinsert the key into the console.
During the first few minutes that you use the tread-
mill, inspect the alignment of the walking belt, and
align the walking belt if necessary (see page 24).
Adjust the incline of the treadmill as desired.
4
To vary the intensity of
your exercise, adjust the
incline of the treadmill
by pressing the Incline
buttons. Note: After the
buttons are pressed, it
may take a moment for
the treadmill to reach the selected incline setting.
10
Download from Www.Somanuals.com. All Manuals Search And Download.
Distance/Incline
display—This display
shows the distance you
Follow your progress with the LED track and
the four displays.
5
have walked and the
LED Track—When the
incline level of the tread-
manual mode or the
mill. The display will al-
iFIT.com mode is
ternate between one
selected, the program
number and the other every seven seconds. Note:
Each time the Incline buttons are pressed, the dis-
play will change to show the incline setting.
display will show a
track representing a
distance of 1/4 mile. As
you exercise, the indicators around the track will
light one at a time until the entire track is lit. A new
lap will then begin.
Speed display—This
display shows the speed
of the walking belt.
Time/Segment Time
display—When the
manual mode or the
iFIT.com mode is
Note: The speed can be
selected, this display
displayed in either miles
will show the elapsed
per hour or kilometers
time. When a preset
per hour. The MPH or
Km/H indicator below
the Speed display will
light to show which unit
of measurement is selected. To change the unit of
measurement, first hold down the Stop button
while inserting the key into the console. The
Speed display will show an E for English miles or
an M for metric kilometers. Pressing the Speed +
button will change the unit of measurement. When
the desired unit of measurement is selected, re-
move and then reinsert the key.
program or a pulse program is selected, the dis-
play will show both the time remaining in the pro-
gram and the time remaining in the current seg-
ment of the program. The display will alternate be-
tween one number and the other every seven sec-
onds.
Pulse/Calories
display—This display
shows the approximate
number of calories you
have burned. If the op-
tional chest pulse sen-
sor is worn, the display
When you are finished exercising, stop the
walking belt and remove the key.
6
will also show your heart rate. The display will al-
ternate between one number and the other every
seven seconds. If the handgrip pulse sensor is
used, the display will show your heart rate contin-
uously while your hands are on the pulse sensor.
Step onto the foot rails, press the Stop button, and
adjust the incline of the treadmill to the lowest
level. The incline must be at the lowest level
when the treadmill is raised to the storage po-
sition or the treadmill will be damaged. Next, re-
move the key from the console and put it in a se-
cure place. Note: If the displays and indicators
on the console remain lit after the key is re-
moved, the console is in the “demo” mode.
Refer to page 20 and turn off the demo mode.
To use the hand-
grip pulse sensor,
stand on the foot
rails and place
Metal
Contacts
your hands on the
metal contacts on
the handrail as
shown—avoid
moving your
hands. After a few
When you are finished using the treadmill, move
the on/off switch near the power cord to the off
position and unplug the power cord.
seconds, one or two dashes will appear in the
Pulse/Calories display and then your heart rate
will be shown. For the most accurate heart rate
reading, hold the contacts for about 15 seconds.
11
Download from Www.Somanuals.com. All Manuals Search And Download.
in the program display.) The speed settings for the
next five segments will be shown in the five
columns to the right.
HOW TO USE THE PRESET PROGRAMS
Insert the key into the console.
1
When only three seconds remain in the first seg-
ment of the program, both the Current Segment
column and the column to the right will flash and a
tone will sound. In addition, if the speed and/or
incline of the treadmill is about to change, the
Speed display and/or the Distance/Incline display
will flash to alert you, and three tones will sound.
When the first segment is completed, all speed
settings will move one column to the left. The
speed setting for the second segment will then be
shown in the flashing Current Segment column
and the treadmill will automatically adjust to the
speed and incline settings for the second seg-
ment.
See HOW TO TURN ON THE POWER on page 10.
Select one of the four preset programs.
2
When the key is
inserted, the
manual mode
will be selected.
To select one of
the preset pro-
grams, press
the Select
Workout button
repeatedly until one of the four preset program in-
dicators lights. When a preset program is se-
lected, the Distance/Incline display will flash the
maximum incline setting for the program for six
seconds, and the Speed display will flash the
maximum speed setting.
The program will continue in this way until the
speed setting for the final segment is shown in the
Current Segment column and no time remains in
the Time/Segment Time display. The walking belt
will then slow to a stop.
Note: Each time a segment ends and the speed
settings move one column to the left, if all of the
indicators in the Current Segment column are lit,
the speed settings will move downward so that only
the highest indicators in the columns will appear in
the program display. When the speed settings
move to the left again and not all of the indicators
in the Current Segment column are lit, the speed
settings will move back up.
The profiles printed on the right side of the console
show how the speed and incline of the treadmill will
change during the preset programs. The numbers
at the left ends of the profiles show the speed and
incline ranges for the programs. The program dis-
play will show a simplified profile of the program.
The Time/Segment Time display will show how
long the selected program will last.
Press the Start button or the Speed + button to
start the program.
3
If the speed or incline setting for the current
segment is too high or too low, you can manually
override the setting by pressing the Speed or
Incline buttons on the console. Every few times
one of the Speed buttons is pressed, an additional
indicator will light or darken in the Current Segment
column. If any of the columns to the right of the
Current Segment column have the same number
of lit indicators as the Current Segment column,
an additional indicator will light or darken in those
columns as well. Note: If you manually adjust the
speed setting so that all of the indicators in the
Current Segment column are lit, the speed settings
in the program display will not move downward as
described above. When the current segment of
the program ends, the treadmill will automati-
cally adjust to the speed and incline settings
for the next segment.
A moment after the button is pressed, the tread-
mill will automatically adjust to the first speed and
incline settings for the program. Hold the handrails
and begin walking.
Each program is divided into several time seg-
ments of different lengths. The Time/Segment
Time display shows both the time remaining in the
program and the time remaining in the current
segment. One speed setting and one incline set-
ting are programmed
for each segment. The
Current Segment
speed setting for the
first segment will be
shown in the flashing
Current Segment col-
umn of the program
display. (The incline
settings are not shown
12
Download from Www.Somanuals.com. All Manuals Search And Download.
To stop the program temporarily, press the Stop
button. All displays will pause and the Time/
Segment Time display will begin to flash. To
restart the program, press the Start button or the
Speed + button. To end the program, press the
Stop button, remove the key, and then reinsert the
key.
HOW TO USE THE PULSE PROGRAMS
WARNING:
If you have heart prob-
lems, or if you are over 60 years of age and
have been inactive, do not use the pulse pro-
grams. If you are taking medication regularly,
consult your physician to find whether the
medication will affect your exercise heart rate.
Use the optional hand weights, if desired.
4
If one of the two cross
training programs is se-
lected, the Cross
Training Indicator
below the Time/
Segment Time display
Insert the key into the console.
1
See HOW TO TURN ON THE POWER on page 10.
will periodically flash.
Put on the optional chest pulse sensor.
While the indicator is flashing, use the optional
hand weights for upper body exercise as you walk
on the treadmill.
2
To use a pulse program, you must wear the op-
tional chest pulse sensor (see page 20). To put
on the chest pulse sensor, follow the instructions
included with the chest pulse sensor.
WARNING:
Using the
Select one of the two pulse programs.
optional hand weights and not holding the
handrails may compromise your ability to
maintain your balance. Exercises using
hand weights should be attempted only by
experienced users.
3
When the key is
inserted, the
manual mode will
be selected. To
select one of the
pulse programs,
press the Select
Workout button
repeatedly until one of the two pulse program indi-
cators lights.
Follow your progress with the four displays.
Refer to step 5 on page 11.
5
6
When the program has ended, remove the key.
The profiles on the console show how the target
heart rate will change during the programs. The
program display will show a simplified profile of
the program. The Time/Segment Time display will
show how long the selected program will last.
Step onto the foot rails and make sure that the in-
cline of the treadmill is at the lowest setting. The
incline must be at the lowest setting when the
treadmill is raised to the storage position. Next,
remove the key from the console and put it in a se-
cure place. Note: If the displays and indicators
on the console remain lit after the key is re-
moved, the console is in the “demo” mode.
Refer to page 20 and turn off the demo mode.
Enter your age.
4
When a pulse
program is se-
lected, the word
AGE will appear
in the Pulse/
Calories display.
When you are finished using the treadmill, move
the on/off switch near the power cord to the off
position and unplug the power cord.
If you have al-
ready entered your age, simply press the Enter
button. If you have not entered your age, press the
+ or – button. The current age setting will then ap-
pear in the display. Press the buttons again to
enter your age. The buttons can be held down to
enter your age quickly. When your age is shown,
press the Enter button.
13
Download from Www.Somanuals.com. All Manuals Search And Download.
When only three seconds remain in the first seg-
ment of the program, both the Current Segment
column and the column to the right will flash, a se-
ries of tones will sound, and the Speed display
and the Distance/Incline display will flash. When
the first segment is completed, all heart rate set-
tings will move one column to the left. The heart
rate setting for the second segment will then be
shown in the flashing Current Segment column,
and the speed and/or incline of the treadmill will
change, if needed, to bring your heart rate closer to
the heart rate setting for the second segment.
Enter a maximum heart rate setting.
5
After you have
entered your
age, the letters
PLS will appear
in the Pulse/
Calories display.
Press the + or –
button. A number will then appear in the display.
This number is the maximum heart rate setting for
the program. If Pulse program 1 is selected, the
maximum heart rate setting can be from 65% to
85% of your maximum possible heart rate; if Pulse
program 2 is selected, the maximum heart rate
setting can be from 65% to 80% of your maximum
possible heart rate.
The program will continue until no time remains in
the Time/Segment Time display. The walking belt
will then slow to a stop.
If the speed or incline setting for the current seg-
ment is too high or too low, you can adjust the set-
ting with the Speed or Incline buttons. However, if
you decrease the speed, the incline will automati-
cally increase; if you increase the speed, the in-
cline will decrease. If you increase the incline, the
speed will decrease; if you decrease the incline,
the speed will increase. The treadmill will always
attempt to keep your heart rate near the target
heart rate setting for the current segment. Note:
When the incline reaches the lowest setting, the
speed cannot be increased any further. When the
incline reaches the highest setting, the speed can-
not be decreased any further.
Note: Your maximum possible heart rate is esti-
mated by subtracting your age from 220. For ex-
ample, if you are 30 years old, your maximum pos-
sible heart rate is 190 beats per minute (220 – 30
= 190). Therefore, if Pulse program 1 is selected,
the maximum heart rate setting can be from 123 to
161 beats per minute (65% of 190 is 123; 85% of
190 is 161).
If you want to change the maximum heart rate set-
ting, press the + and – buttons. The buttons can
be held down to change the setting quickly. When
the desired setting is shown, press the Enter button.
If your pulse is not detected during the program,
the letters PLS will flash in the Pulse/Calories dis-
play. In addition, the speed and/or incline of the
treadmill may automatically decrease until your
pulse is detected. If this occurs, refer to the instruc-
tions included with the chest pulse sensor.
Press the Start button or the Speed + button to
start the program.
6
A moment after the button is pressed, the tread-
mill will automatically adjust to the first speed and
incline settings for the program. Hold the handrails
and begin walking.
Pulse programs cannot be stopped temporarily
and then restarted. To stop the program at any
time, press the Stop button.
Each program is divided into several time segments
of different lengths. The Time/Segment Time dis-
play will show both the time remaining in the pro-
gram and the time remaining in the current seg-
ment. One target heart rate setting is programmed
for each segment. The heart rate setting for the
first segment will be
Follow your progress with the four displays.
Refer to step 5 on page 11.
7
8
shown in the flashing
When the program has ended, remove the key.
See step 6 on page 13.
Current Segment
Current Segment col-
umn of the program
display. The heart rate
settings for the next five
segments will be shown
in the five columns to
the right.
14
Download from Www.Somanuals.com. All Manuals Search And Download.
HOW TO CONNECT YOUR PORTABLE STEREO
HOW TO CONNECT THE TREADMILL TO
YOUR CD PLAYER, VCR, OR COMPUTER
Note: If your stereo has an RCA-type AUDIO OUT
jack, see instruction A below. If your stereo has a
3.5mm LINE OUT jack, see instruction B. If your
stereo has only a PHONES jack, see instruction C.
To use iFIT.com CDs, the treadmill must be con-
nected to your portable CD player, portable stereo,
home stereo, or computer with CD player. See pages
15 and 16 for connecting instructions. To use iFIT.com
videocassettes, the treadmill must be connected to
your VCR. See page 17 for connecting instructions. To
use iFIT.com programs directly from our Web site,
the treadmill must be connected to your home com-
puter. See page 16 for connecting instructions.
A. Plug one end of the audio cable into the jack on the
front of the treadmill near the power cord. Plug the
other end of the cable into the included adapter. Plug
the adapter into an AUDIO OUT jack on your stereo.
A
HOW TO CONNECT YOUR PORTABLE CD PLAYER
AUDIO OUT
RIGHT
LEFT
Note: If your CD player has separate LINE OUT and
PHONES jacks, see instruction A below. If your CD
player has only one jack, see instruction B.
Audio
Cable
Adapter
A. Plug one end of the audio cable into the jack on the
front of the treadmill near the power cord. Plug the
other end of the cable into the LINE OUT jack on
your CD player. Plug your headphones into the
PHONES jack.
B. Plug one end of the audio cable into the jack on the
front of the treadmill near the power cord. Plug the
other end of the cable into the LINE OUT jack on
your stereo.
A
PHONES LINE OUT
LINE OUT
PHONES
B
Head-
phones
Audio
Cable
LINE OUT
Audio
Cable
B. Plug one end of the audio cable into the jack on the
front of the treadmill near the power cord. Plug the
other end of the cable into a 3.5mm Y-adapter
(available at electronics stores). Plug the Y-adapter
into the PHONES jack on your CD player. Plug your
headphones into the other side of the Y-adapter.
C. Plug one end of the audio cable into the jack on the
front of the treadmill near the power cord. Plug the
other end of the cable into a 3.5mm Y-adapter
(available at electronics stores). Plug the Y-adapter
into the PHONES jack on your stereo. Plug your
headphones into the other side of the Y-adapter.
B
PHONES
C
PHONES
3.5mm
Y-adapter
Audio
Cable
PHONES
3.5mm
Y-adapter
Audio
Cable
Headphones
Headphones
15
Download from Www.Somanuals.com. All Manuals Search And Download.
HOW TO CONNECT YOUR HOME STEREO
HOW TO CONNECT YOUR COMPUTER
Note: If your stereo has an unused LINE OUT jack,
see instruction A below. If the LINE OUT jack is
being used, see instruction B.
Note: If your computer has a 3.5mm LINE OUT jack,
see instruction A. If your computer has only a
PHONES jack, see instruction B.
A. Plug one end of the audio cable into the jack on the
front of the treadmill near the power cord. Plug the
other end of the cable into the included adapter.
Plug the adapter into the LINE OUT jack on your
stereo.
A. Plug one end of the audio cable into the jack on the
front of the treadmill near the power cord. Plug the
other end of the cable into the LINE OUT jack on
your computer.
A
A
CD
LINE OUT
VCR
Amp
LINE OUT
Audio
Cable
LINE OUT
Audio
Cable
Adapter
B. Plug one end of the audio cable into the jack on the
front of the treadmill near the power cord. Plug the
other end of the cable into a 3.5mm Y-adapter
(available at electronics stores). Plug the Y-adapter
into the PHONES jack on your computer. Plug your
headphones or speakers into the other side of the
Y-adapter.
B. Plug one end of the audio cable into the jack on the
front of the treadmill near the power cord. Plug the
other end of the cable into the included adapter.
Plug the adapter into an RCA Y-adapter (available
at electronics stores). Next, remove the wire that is
currently plugged into the LINE OUT jack on your
stereo and plug the wire into the unused side of the
Y-adapter. Plug the Y-adapter into the LINE OUT
jack on your stereo.
B
PHONES
B
CD
Audio
Cable
3.5mm
Y-adapter
VCR
Amp
LINE OUT
Headphones/Speakers
RCA Y-adapter
Audio
Adapter
Cable
Wire removed from
LINE OUT jack
16
Download from Www.Somanuals.com. All Manuals Search And Download.
HOW TO CONNECT YOUR VCR
HOW TO USE IFIT.COM CD AND VIDEO
PROGRAMS
Note: If your VCR has an unused AUDIO OUT jack,
see instruction A below. If the AUDIO OUT jack is
being used, see instruction B. If you have a TV
with a built-in VCR, see instruction B. If your VCR
is connected to your home stereo, see HOW TO
CONNECT YOUR HOME STEREO on page 16.
To use iFIT.com CDs or videocassettes, the treadmill
must be connected to your portable CD player, portable
stereo, home stereo, computer with CD player, or
VCR. See HOW TO CONNECT THE TREADMILL TO
YOUR CD PLAYER, VCR, OR COMPUTER on page
15. Note: To purchase iFIT.com CDs or iFIT.com
videocassettes, call toll-free 1-800-735-0768.
A. Plug one end of the audio cable into the jack on the
front of the treadmill near the power cord. Plug the
other end of the cable into the included adapter.
Plug the adapter into the AUDIO OUT jack on your
VCR.
Follow the steps below to use an iFIT.com CD or video
program.
A
Insert the key into the console.
ANT IN
.
VIDEO AUDIO
IN
RF OUT
1
CH
3
4
OUT
AUDIO OUT
See HOW TO TURN ON THE POWER on page 10.
RIGHT
LEFT
Select the iFIT.com mode.
2
Audio
Cable
Adapter
When the key is in-
serted, the manual
mode will be selected.
To use iFIT.com CDs or
videocassettes, press
the iFIT.com button.
The interactivity indica-
tor will light.
B. Plug one end of the audio cable into the jack on the
front of the treadmill near the power cord. Plug the
other end of the cable into the included adapter.
Plug the adapter into an RCA Y-adapter (available
at electronics stores). Next, remove the wire that is
currently plugged into the AUDIO OUT jack on your
VCR and plug the wire into the unused side of the
Y-adapter. Plug the Y-adapter into the AUDIO OUT
jack on your VCR.
Insert the iFIT.com CD or videocassette.
3
If you are using an iFIT.com CD, insert the CD into
your CD player. If you are using an iFIT.com video-
cassette, insert the videocassette into your VCR.
Press the PLAY button on your CD player or
VCR.
4
B
ANT IN
.
VIDEO AUDIO
IN
RF OUT
CH
3
4
OUT
A moment after the button is pressed, your per-
sonal trainer will begin guiding you through your
workout. Simply follow your personal trainer’s
instructions. Note: If the Time/Segment Time dis-
play is flashing, press the Start button or the
Speed + button on the console. The treadmill will
not respond to a CD or video program when the
Time/Segment Time display is flashing.
RCA Y-adapter
Adapter
Audio
Cable
Wire removed from
AUDIO OUT jack
During the CD or video program, an electronic
“chirping” sound will alert you when the speed
and/or incline of the treadmill is about to change.
CAUTION: Always listen for the “chirp” and be
prepared for speed and/or incline changes. In
some instances, the speed and/or incline may
change before the personal trainer describes
the change.
17
Download from Www.Somanuals.com. All Manuals Search And Download.
If the speed or incline settings are too high or too
low, you can manually override the settings at any
time by pressing the Speed or Incline buttons on
the console. However, when the next “chirp” is
heard, the speed and/or incline will change to
the next settings of the CD or video program.
• Adjust the volume of your CD player or VCR.
If the volume is too high or too low, the con-
sole may not detect the program signals.
• Make sure that the audio cable is properly
connected, that it is fully plugged in, and that
it is not wrapped around a power cord.
To stop the walking belt at any time, press the
Stop button on the console. The Time/Segment
Time display will begin to flash. To restart the pro-
gram, press the Start button or the Speed + but-
ton. After a moment, the walking belt will begin to
move at 1 mph. When the next “chirp” is heard,
the speed and incline will change to the next
settings of the CD or video program. The pro-
gram can also be stopped by pressing the Stop
button on your CD player or VCR.
• If you are using your portable CD player and
the CD skips, set the CD player on the floor or
another flat surface instead of on the console.
Follow your progress with the four displays.
5
6
See step 5 on page 11.
When the program is completed, remove the
key.
When the CD or video program is completed, the
walking belt will stop and the Time/Segment Time
display will begin to flash. Note: To use another
CD or video program, press the Stop button or re-
move the key and go to step 1 on page 17.
See step 6 on page 13.
CAUTION: Always remove iFIT.com CDs and
videos from your CD player or VCR when you
are not using them.
Note: If the speed or incline of the treadmill
does not change when a “chirp” is heard:
• Make sure that the iFIT.com indicator is lit and
that the Time/Segment Time display is not
flashing. If the Time/Segment Time display is
flashing, press the Start button or the Speed
+ button on the console.
18
Download from Www.Somanuals.com. All Manuals Search And Download.
Return to the treadmill and stand on the foot
rails. Find the clip attached to the key and slide
the clip onto the waistband of your clothes.
HOW TO USE PROGRAMS DIRECTLY FROM
OUR WEB SITE
7
When the on-screen countdown ends, the program
will begin and the walking belt will begin to move.
Hold the handrails, step onto the walking belt, and
begin walking. During the program, an electronic
“chirping” sound will alert you when the speed
and/or incline of the treadmill is about to change.
CAUTION: Always listen for the “chirp” and be
prepared for speed and/or incline changes.
basic programs, audio programs, and video programs
directly from the internet. Additional options, such as
on-line competitions, personal training sessions via the
internet, and online tracking of your workout history are
To use programs from our Web site, the treadmill must
be connected to your home computer. See HOW TO
CONNECT YOUR COMPUTER on page 16. In
addition, you must have an internet connection and
an internet service provider. A list of specific system
requirements will be found on our Web site.
If the speed or incline settings are too high or too
low, you can manually override the settings at any
time by pressing the Speed or Incline buttons on
the console. However, when the next “chirp” is
heard, the speed and/or incline will change to
the next settings for the program.
Follow the steps below to use a program from our
Web site.
To stop the walking belt at any time, press the
Stop button on the console. The Time/Segment
Time display will begin to flash. To restart the pro-
gram, press the Start button or the Speed + but-
ton. After a moment, the walking belt will begin to
move at 1 mph. When the next “chirp” is heard,
the speed and incline will change to the next
settings for the program.
Insert the key into the console.
1
See HOW TO TURN ON THE POWER on page 10.
Select the iFIT.com mode.
2
When the key is in-
serted, the manual
mode will be selected.
To use a program from
our Web site, press the
iFIT.com button. The
interactivity indicator
will light.
When the program is completed, the walking belt
will stop and the Time/Segment Time display will
begin to flash. Note: To use another program,
press the Stop button and go to step 5.
Note: If the speed or incline of the treadmill
does not change when a “chirp” is heard, make
sure that the iFIT.com indicator is lit and that
the Time/Segment Time display is not flashing.
In addition, make sure that the audio cable is
properly connected, that it is fully plugged in,
and that it is not wrapped around a power cord.
Go to your computer and start an internet
connection.
3
Start your web browser, if necessary, and go to
4
Follow your progress with the four displays.
See step 5 on page 11.
8
9
Follow the desired links on our Web site to se-
lect a program.
5
Read and follow the on-line instructions for using a
program.
When the program has ended, remove the key.
See step 6 on page 13.
Follow the on-line instructions to start the
program.
6
When you start the program, an on-screen count-
down will begin.
19
Download from Www.Somanuals.com. All Manuals Search And Download.
THE INFORMATION MODE/DEMO MODE
THE OPTIONAL CHEST PULSE SENSOR
The console features an information mode that keeps
track of the total number of hours that the treadmill has
been operated and the total number of miles that the
walking belt has moved. The information mode also al-
lows you to switch the console from miles per hour to
kilometers per hour. In addition, the information mode
allows you to turn on and turn off the demo mode.
An optional chest pulse sensor adds even more
features to the console. The chest pulse sensor contin-
uously monitors your heart rate during your workouts
and allows you to use the console’s two pulse pro-
grams. To purchase the optional chest pulse sen-
sor, call toll-free 1-800-734-2377.
To select the information mode, hold down the Stop
button while inserting the key into the console. When
the information mode is selected, the following informa-
tion will be shown:
The Time/Segment Time
display will show the total
number of hours that the
treadmill has been used.
OPTIONAL HAND WEIGHTS
The Distance/Incline display
will show the total number of
miles that the walking belt
has moved.
Optional hand weights
let you exercise your
upper body while you
walk on the treadmill.
The hand weights fit
into convenient holders
in the console. To pur-
chase hand weights,
call toll-free 1-800-
772-0257.
An E for English miles or an
M for metric kilometers will
appear in the Speed display.
Press the Speed + button to
change the unit of measure-
ment.
IMPORTANT: The
Pulse/Calories display
should be blank. If a “d”
appears in the display, the
console is in the “demo”
mode. This mode is in-
tended to be used only
when a treadmill is displayed in a store. When the con-
sole is in the demo mode, the power cord can be
plugged in, the key can be removed from the console,
and the displays and indicators on the console will au-
tomatically light in a preset sequence, although the but-
tons on the console will not operate. If a “d” appears
in the Pulse/Calories display when the information
mode is selected, press the Speed – button so the
Pulse/Calories display is blank.
To exit the information mode, remove the key from the
console.
20
Download from Www.Somanuals.com. All Manuals Search And Download.
HOW TO FOLD AND MOVE THE TREADMILL
HOW TO FOLD THE TREADMILL FOR STORAGE
Before folding the treadmill, adjust the incline to the
lowest position. If this is not done, the treadmill may be
permanently damaged. Next, unplug the power cord.
CAUTION: You must be able to safely lift 45 pounds (20
kg) to raise, lower, or move the treadmill.
1. Hold the treadmill in the locations shown at the right. To
decrease the possibility of injury, bend your legs and
keep your back straight. As you raise the treadmill,
make sure to lift with your legs rather than your back.
Raise the treadmill about halfway to the vertical position.
2. Move your right hand to the position shown and hold the
treadmill firmly. Using your left hand, pull the latch knob
to the left and hold it. Raise the treadmill until all parts of
the treadmill are past the latch pin. Then, release the
latch knob. Make sure that the latch knob is fully re-
leased so that the latch pin is securely holding the
catch.
Latch
Pin
To protect the floor or carpet from damage, place a
mat under the treadmill. Keep the treadmill out of
direct sunlight. Do not leave the treadmill in the stor-
age position in temperatures above 85° Fahrenheit.
Latch
Knob
Catch
HOW TO MOVE THE TREADMILL
Before moving the treadmill, convert the treadmill to the
storage position as described above. Make sure that the
latch pin is securely holding the catch.
1. Hold the handrails and place one foot on the base.
2. Tilt the treadmill back until it rolls freely on the wheels.
Carefully move the treadmill to the desired location. To re-
duce the risk of injury, use extreme caution while
moving the treadmill. Do not attempt to move the
treadmill over an uneven surface.
Base
Front Wheels
3. Place one foot on the wheel, and carefully lower the
treadmill until the base is resting in the storage position.
21
Download from Www.Somanuals.com. All Manuals Search And Download.
HOW TO LOWER THE TREADMILL FOR USE
1. Hold the upper end of the treadmill with your right hand
as shown. Using your left hand, pull the latch knob to the
left and hold it. Pivot the treadmill down until the catch is
past the pin. Slowly release the latch knob.
Latch
Pin
Latch
Knob
Catch
2. Hold the treadmill firmly with both hands, and lower the
treadmill to the floor. Do not drop the treadmill frame
to the floor. CAUTION: To decrease the possibility of
injury, bend your legs and keep your back straight.
22
Download from Www.Somanuals.com. All Manuals Search And Download.
TROUBLESHOOTING AND MAINTENANCE
Most treadmill problems can be solved by following the instructions below. If further assistance is
needed, please call our Customer Service Department toll-free at 1-800-999-3756, Monday through Friday,
6 a.m. until 6 p.m. Mountain Time (excluding holidays).
PROBLEM
SOLUTION
1. The power does not
turn on
a. Make sure that the power cord is plugged into a surge suppressor, and that the
surge suppressor is plugged into a properly grounded outlet (see page 7). Use
only a single-outlet surge suppressor that meets all of the specifications described
on page 7. Important: The treadmill is not compatible with GFCI-equipped outlets.
b. Make sure that the key is fully inserted into the console.
c. Check the circuit breaker located on the frame near
c
the power cord. If the switch protrudes as shown, the
circuit breaker has tripped. To reset the circuit
breaker, wait for five minutes and then press the
switch back in.
Tripped
Reset
d. Check the on/off switch located on the frame near
the power cord. The switch must be in the on posi-
tion.
d
On
Position
2. The power turns off
during use
a. Check the circuit breaker located on the treadmill frame near the power cord (see
1. c. above). If the circuit breaker has tripped, wait for five minutes and then press
the switch back in.
b. Make sure that the power cord is plugged in. If the power cord is plugged in, un-
plug it, wait for five minutes, and then plug it back in.
c. Remove the key from the console and then reinsert it.
d. Unplug the power cord, wait for five minutes, and then plug the power cord back in.
e. Make sure that the on/off switch is in the on position (see 1. d. above).
3. The walking belt
slows when walked
on
a. Use only a single-outlet surge suppressor that meets all of the specifications de-
scribed on page 7.
b. If the walking belt is overtightened, tread-
b
3”–4”
mill performance may decrease and the
walking belt may be permanently dam-
aged. Remove the key and UNPLUG THE
POWER CORD. Using the included allen
wrench, turn both rear roller adjustment
bolts counterclockwise 1/4 of a turn. When
the walking belt is properly tightened, you
should be able to lift the edges of the
walking belt 3 to 4 inches off the walking
platform. Be careful to keep the walking
belt centered. Plug in the power cord, in-
Rear Roller Adjustment Bolts
sert the key and run the treadmill for a few minutes. Repeat until the walking belt
is properly tightened.
23
Download from Www.Somanuals.com. All Manuals Search And Download.
PROBLEM
SOLUTION
4. The walking belt is
off-center or slips
when walked on
a. If the walking belt is off-center, first re-
move the key and UNPLUG THE POWER
CORD. If the walking belt has shifted to
the left, use the allen wrench to turn the
left rear roller bolt clockwise 1/2 of a turn; if
the walking belt has shifted to the right,
turn the bolt counterclockwise 1/2 of a turn.
Be careful not to overtighten the walking
belt. Plug in the power cord, insert the key
and run the treadmill for a few minutes.
Repeat until the walking belt is centered.
a
b. If the walking belt slips when walked on,
first remove the key and UNPLUG THE
POWER CORD. Using the allen wrench,
turn both rear roller bolts clockwise 1/4 of a
turn. When the walking belt is correctly
tightened, you should be able to lift each
side of the walking belt 3 to 4 inches off the
walking platform. Be careful to keep the
walking belt centered. Plug in the power
cord, insert the key and carefully walk on
b
the treadmill for a few minutes. Repeat until the walking belt is properly tightened.
5. The displays of the
console do not func-
tion properly
a. Remove the key from the console and UN-
a
PLUG THE POWER CORD. Next, remove
the screws from the hood and carefully re-
move the hood. Locate the Reed Switch
(17) and the Magnet (12) on the left side of
the Pulley (11). Turn the Pulley until the
Magnet is aligned with the Reed Switch.
Make sure that the gap between the
Magnet and the Reed Switch is about
1/8”. If necessary, loosen the Reed Switch
1/8”
11
99
12
17
Top
View
Screw (99) and move the Reed Switch slightly. Retighten the Screw. Re-attach the
hood and run the treadmill for a few minutes to check for a correct speed reading.
24
Download from Www.Somanuals.com. All Manuals Search And Download.
EXERCISE GUIDELINES
uses easily accessible carbohydrate calories for en-
ergy. Only after the first few minutes does your body
begin to use stored fat calories for energy. If your goal
is to burn fat, adjust the speed or incline of the tread-
mill until your heart rate is near the lowest number in
your training zone.
WARNING:
Before beginning this
or any exercise program, consult your physi-
cian. This is especially important for individu-
als over the age of 35 or individuals with pre-
existing health problems.
For maximum fat burning, adjust the speed or incline
of the treadmill until your heart rate is near the middle
number in your training zone.
The pulse sensor is not a medical device.
Various factors, including your movement,
may affect the accuracy of heart rate readings.
The sensor is intended only as an exercise aid
in determining heart rate trends in general.
Aerobic Exercise
If your goal is to strengthen your cardiovascular sys-
tem, your exercise must be “aerobic.” Aerobic exercise
is activity that requires large amounts of oxygen for
prolonged periods of time. This increases the demand
on the heart to pump blood to the muscles, and on the
lungs to oxygenate the blood. For aerobic exercise,
adjust the speed or incline of the treadmill until your
heart rate is near the highest number in your training
zone.
The following guidelines will help you to plan your ex-
ercise program. For more detailed exercise informa-
tion, obtain a reputable book or consult your physician.
EXERCISE INTENSITY
Whether your goal is to burn fat or to strengthen your
cardiovascular system, the key to achieving the
desired results is to exercise with the proper intensity.
The proper intensity level can be found by using your
heart rate as a guide. The chart below shows recom-
mended heart rates for fat burning and aerobic exercise.
WORKOUT GUIDELINES
Each workout should include the following three parts:
A Warm-up—Start each workout with 5 to 10 minutes
of stretching and light exercise. A proper warm-up in-
creases your body temperature, heart rate and circula-
tion in preparation for exercise.
Training Zone Exercise—After warming up, increase
the intensity of your exercise until your pulse is in your
training zone for 20 to 60 minutes. (During the first few
weeks of your exercise program, do not keep your
pulse in your training zone for longer than 20 minutes.)
Breathe regularly and deeply as you exercise—never
hold your breath.
To find the proper heart rate for you, first find your age
near the bottom of the chart (ages are rounded off to
the nearest ten years). Next, find the three numbers
above your age. The three numbers define your “train-
ing zone.” The lower two numbers are recommended
heart rates for fat burning; the highest number is the
recommended heart rate for aerobic exercise.
A Cool-down—Finish each workout with 5 to 10 min-
utes of stretching to cool down. This will increase the
flexibility of your muscles and will help prevent post-ex-
ercise problems.
To measure your heart rate during exercise, use the
handgrip pulse sensor or the optional chest pulse sen-
sor (see page 20). If your heart rate is too high or too
low, adjust the speed or incline of the treadmill.
EXERCISE FREQUENCY
To maintain or improve your condition, complete three
workouts each week, with at least one day of rest be-
tween workouts. After a few months, you may com-
plete up to five workouts each week if desired. The key
to success is to make exercise a regular and enjoyable
part of your everyday life.
Fat Burning
To burn fat effectively, you must exercise at a relatively
low intensity level for a sustained period of time.
During the first few minutes of exercise, your body
25
Download from Www.Somanuals.com. All Manuals Search And Download.
SUGGESTED STRETCHES
The correct form for several basic stretches is shown at the right. Move slowly as you stretch—never bounce.
1. Toe Touch Stretch
1
Stand with your knees bent slightly and slowly bend forward from
your hips. Allow your back and shoulders to relax as you reach
down toward your toes as far as possible. Hold for 15 counts,
then relax. Repeat 3 times. Stretches: Hamstrings, back of knees
and back.
2. Hamstring Stretch
Sit with one leg extended. Bring the sole of the opposite foot to-
2
ward you and rest it against the inner thigh of your extended leg.
Reach toward your toes as far as possible. Hold for 15 counts,
then relax. Repeat 3 times for each leg. Stretches: Hamstrings,
lower back and groin.
3. Calf/Achilles Stretch
With one leg in front of the other, reach forward and place your
hands against a wall. Keep your back leg straight and your back
foot flat on the floor. Bend your front leg, lean forward and move
your hips toward the wall. Hold for 15 counts, then relax. Repeat
3
3 times for each leg. To cause further stretching of the achilles
tendons, bend your back leg as well. Stretches: Calves, achilles
tendons and ankles.
4
4. Quadriceps Stretch
With one hand against a wall for balance, reach back and grasp
one foot with your other hand. Bring your heel as close to your
buttocks as possible. Hold for 15 counts, then relax. Repeat 3
times for each leg. Stretches: Quadriceps and hip muscles.
5. Inner Thigh Stretch
Sit with the soles of your feet together and your knees outward.
Pull your feet toward your groin area as far as possible. Hold for
15 counts, then relax. Repeat 3 times. Stretches: Quadriceps
and hip muscles.
5
26
Download from Www.Somanuals.com. All Manuals Search And Download.
PART LIST—Model No. PFTL71330
R0803A
To locate the parts listed below, see the EXPLODED DRAWING attached in the center of this manual.
Key
Key
Key
No. Qty. Description
No. Qty. Description
No. Qty. Description
1
2
3
4
5
6
7
8
9
10
11
12
13
2
1
1
4
1
1
4
1
2
1
1
1
9
Foot Rail
Flywheel
Right Rail Endcap
Isolator
Latch Catch
Platform
Walking Deck Screw
Walking Belt
Frame Pivot Bolt
Latch Assembly
Front Roller/Pulley
Magnet
Front Wheel Nut/
Pivot Nut
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
1
2
4
4
1
2
2
1
1
1
2
1
1
2
1
1
2
1
1
4
1
1
1
1
1
1
2
1
Ground Wire
Rear Foot
Isolator Washer
Isolator Nut
Filter Wire
Roller Adj. Washer
Rear Roller Adj. Bolt
Rear Endcap
Frame
Allen Wrench
Rear Platform Screw
Rear Roller
Pulse Wire Harness
Frame Star Washer
Book Rack
Left Foam Grip
Roller Star Washer
Pulse Sensor
Upright
Base Mounting Screw
Latch Knob
Latch Knob Sleeve
Latch Knob Spring
Latch Pin Collar
Pin Clip
93
94
2
6
Incline Motor Spacer
Sensor Cover Screw/
Rear Foot
Tie Holder
Tie
8” Cable Tie
Bumper
Bumper Screw
On/Off Switch
Circuit Breaker
Power Cord
Power Cord Grommet
Warning Decal
Foot Rail Insert
Jack
iFIT.com Audio Cable
Foam Grip Screw/
Belt Guide Screw
Left Rail Endcap
Foam Pad
12” Audio Wire
Long Console Screw
Hood Screw
Frame Pivot Washer
Console Ground Wire
Lift Motor Bolt
95
96
97
98
99
100
101
102
103
104
105
106
107
2
2
5
4
4
1
1
1
1
2
2
1
1
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
2
2
1
1
1
1
1
2
1
1
1
1
2
4
1
1
4
1
1
1
4
1
1
1
1
1
6
Spacer Insert
Frame Pivot Spacer
Reed Switch Clip
Reed Switch
108 10
Lift Frame
109
110
111
112
113
114
115
116
117
118
119
1
2
1
3
4
4
1
1
2
1
2
Motor Sleeve
Motor Pivot Nut
Pulse Bar Bolt
Motor Belt
Motor Flange Nut
Motor
Motor Tension Bolt
Static Warning Decal
Hood Bracket
Motor Tension Washer
Lift Motor Bracket
Front Belly Pan Screw
Lift Motor Bolt
Motor Bolt
Outlet Bracket
Plastic Standoff
Power Supply
Power Supply Bracket
Controller
Latch Pin
Incline Pivot Bolt
Wire Harness
Grommet
Console Screw
Wheel Spacer
Front Wheel
Motor Isolator
Audio Wire Nut
Outlet Bracket
Star Washer
Controller Screw
Motor/Pulley/
75
76
77
78
79
80
81
82
83
84
85
86
87
88
8
2
2
2
1
1
1
1
1
1
1
1
2
5
120
121*
6
1
Wheel Bolt
Flywheel/Fan
Right Foam Grip
Console Base (Top)
Console
122
123
#
#
#
#
#
#
#
1
3
1
1
1
1
1
1
1
1
Tension Star Washer
Nylon Washer
8” Blue Wire, M/F
4” Blue Wire, 2F
4” Black Wire, M/F
4” Black Wire, 2 F
14” White Wire, 2 F
8” Green Wire, 2 Ring
8” Red Wire, M/F
User’s Manual
Key/Clip
Console Base (Bottom)
Pulse Sensor Plate
Upright Wire Harness
Shock
Upright Endcap
Pulley Washer/
Wheel Washer
Pulse Sensor Cover
Latch Warning Decal
Incline Motor
Controller Bracket
Motor Hood
Latch Catch Screw/
Rear Endcap Screw
Motor Belly Pan
Belt Guide
41
42
43
44
45
46
1
2
21
13
1
#
Misc. Screw
89
90
91
92
1
1
1
1
* Includes all parts shown in the box
# These parts are not illustrated
Plastic Fastener
Frame Belly Pan
Pulse Bar
1
Motor Controller Wire
27
Download from Www.Somanuals.com. All Manuals Search And Download.
EXPLODED DRAWING—Model No. PFTL71330
R0803A
Download from Www.Somanuals.com. All Manuals Search And Download.
EXPLODED DRAWING—Model No. PFTL71330
R0803A
Download from Www.Somanuals.com. All Manuals Search And Download.
HOW TO ORDER REPLACEMENT PARTS
To order replacement parts, call our Customer Service Department toll-free at 1-800-999-3756, Monday through
Friday, 6 a.m. until 6 p.m. Mountain Time (excluding holidays). To help us assist you, please be prepared to give
the following information:
• The MODEL NUMBER of the product (PFTL71330)
• The NAME of the product (PROFORM® 725i treadmill)
• The SERIAL NUMBER of the product (see the front cover of this manual)
• The KEY NUMBER and DESCRIPTION of the part(s) (see the PART LIST on page 27)
LIMITED WARRANTY
ICON Health & Fitness, Inc. (ICON), warrants this product to be free from defects in workmanship and
material, under normal use and service conditions, for a period of ninety (90) days from the date of pur-
chase. This warranty extends only to the original purchaser. ICON's obligation under this warranty is lim-
ited to replacing or repairing, at ICON's option, the product through one of its authorized service centers.
All repairs for which warranty claims are made must be pre-authorized by ICON. This warranty does not
extend to any product or damage to a product caused by or attributable to freight damage, abuse, mis-
use, improper or abnormal usage or repairs not provided by an ICON authorized service center; prod-
ucts used for commercial or rental purposes; or products used as store display models. No other war-
ranty beyond that specifically set forth above is authorized by ICON.
ICON is not responsible or liable for indirect, special or consequential damages arising out of or in con-
nection with the use or performance of the product or damages with respect to any economic loss, loss
of property, loss of revenues or profits, loss of enjoyment or use, costs of removal or installation or other
consequential damages of whatsoever nature. Some states do not allow the exclusion or limitation of in-
cidental or consequential damages. Accordingly, the above limitation may not apply to you.
The warranty extended hereunder is in lieu of any and all other warranties and any implied warranties of
merchantability or fitness for a particular purpose is limited in its scope and duration to the terms set
forth herein. Some states do not allow limitations on how long an implied warranty lasts. Accordingly, the
above limitation may not apply to you.
This warranty gives you specific legal rights. You may also have other rights which vary from state to state.
ICON HEALTH & FITNESS, INC., 1500 S. 1000 W., LOGAN, UT 84321-9813
Part No. 199603 R0803A
Printed in USA © 2003 ICON Health & Fitness, Inc.
Download from Www.Somanuals.com. All Manuals Search And Download.
|