Model No. PFTL54509.0
Serial No.
USERʼS MANUAL
Write the serial number in the space
above for reference.
Serial Number
Decal
QUESTIONS?
If you have questions, or if parts are
damaged or missing, DO NOT CON-
TACT THE STORE; please contact
Customer Care.
IMPORTANT: Please register this
product (see the limited warranty
on the back cover of this manual)
before contacting Customer Care.
CALL TOLL-FREE:
1-888-533-1333
Mon.–Fri. 6 a.m.–6 p.m. MT
Sat. 8 a.m.–4 p.m. MT
ON THE WEB:
CAUTION
Read all precautions and instruc-
tions in this manual before using
this equipment. Save this manual
for future reference.
Download from Www.Somanuals.com. All Manuals Search And Download.
IMPORTANT PRECAUTIONS
WARNING:
To reduce the risk of serious injury, read all important precautions and in-
structions in this manual and all warnings on your treadmill before using your treadmill. ICON as-
sumes no responsibility for personal injury or property damage sustained by or through the use of
this product.
1. Before beginning any exercise program, con-
sult your physician. This is especially impor-
tant for persons over age 35 or persons with
pre-existing health problems.
carrying 15 or more amps. No other appliance
should be on the same circuit. Do not use an
extension cord.
12. Use only a single-outlet surge suppressor that
meets all of the specifications described on
page 13. To purchase a surge suppressor, see
your local PROFORM dealer or call the tele-
phone number on the front cover of this man-
ual and order part number 146148, or see your
local electronics store.
2. It is the responsibility of the owner to ensure
that all users of this treadmill are adequately
informed of all warnings and precautions.
3. Use the treadmill only as described.
4. Place the treadmill on a level surface, with at
least 8 ft. (2.4 m) of clearance behind it and 2
ft. (0.6 m) on each side. Do not place the
treadmill on any surface that blocks air open-
ings. To protect the floor or carpet from dam-
age, place a mat under the treadmill.
13. Failure to use a properly functioning surge
suppressor could result in damage to the con-
trol system of the treadmill. If the control sys-
tem is damaged, the walking belt may slow,
accelerate, or stop unexpectedly, which may
result in a fall and serious injury.
5. Keep the treadmill indoors, away from mois-
ture and dust. Do not put the treadmill in a
garage or covered patio, or near water.
14. Keep the power cord and the surge suppres-
sor away from heated surfaces.
6. Do not operate the treadmill where aerosol
products are used or where oxygen is being
administered.
15. Never move the walking belt while the power
is turned off. Do not operate the treadmill if
the power cord or plug is damaged, or if the
treadmill is not working properly. (See TROU-
BLESHOOTING on page 22 if the treadmill is
not working properly.)
7. Keep children under age 12 and pets away
from the treadmill at all times.
8. The treadmill should be used only by persons 16. Read, understand, and test the emergency
weighing 300 lbs. (136 kg) or less.
stop procedure before using the treadmill (see
HOW TO TURN ON THE POWER on page 15).
9. Never allow more than one person on the
treadmill at a time.
17. Never start the treadmill while you are stand-
ing on the walking belt. Always hold the
handrails while using the treadmill.
10. Wear appropriate exercise clothes when
using the treadmill. Do not wear loose clothes
that could become caught in the treadmill.
Athletic support clothes are recommended
for both men and women. Always wear ath-
letic shoes. Never use the treadmill with bare
feet, wearing only stockings, or in sandals.
18. The treadmill is capable of high speeds.
Adjust the speed in small increments to avoid
sudden jumps in speed.
19. The pulse sensor is not a medical device.
Various factors, including the user's move-
ment, may affect the accuracy of heart rate
readings. The pulse sensor is intended only
as an exercise aid in determining heart rate
trends in general.
11. When connecting the power cord (see page
13), plug the power cord into a surge sup-
pressor (not included) and plug the surge
suppressor into a grounded circuit capable of
3
Download from Www.Somanuals.com. All Manuals Search And Download.
20. Never leave the treadmill unattended while it
is running. Always remove the key, unplug
the power cord, and switch the reset/off cir-
cuit breaker to the off position when the
treadmill is not in use. (See the drawing on
page 5 for the location of the circuit breaker.)
24. Inspect and properly tighten all parts of the
treadmill regularly.
25.
DANGER:
Always unplug the power
cord immediately after use, before cleaning the
treadmill, and before performing the mainte-
nance and adjustment procedures described in
this manual. Never remove the motor hood un-
less instructed to do so by an authorized ser-
vice representative. Servicing other than the
procedures in this manual should be performed
by an authorized service representative only.
21. Do not attempt to raise, lower, or move the
treadmill until it is properly assembled. (See
ASSEMBLY on page 6, and HOW TO FOLD
AND MOVE THE TREADMILL on page 20.)
You must be able to safely lift 45 lbs. (20 kg)
to raise, lower, or move the treadmill.
26. This treadmill is intended for in-home use
only. Do not use this treadmill in a commer-
cial, rental, or institutional setting.
22. When folding or moving the treadmill, make
sure that the storage latch is holding the
frame securely in the storage position.
27. Over exercising may result in serious injury
or death. If you feel faint or if you experience
pain while exercising, stop immediately and
cool down.
23. Never insert any object into any opening on
the treadmill.
SAVE THESE INSTRUCTIONS
4
Download from Www.Somanuals.com. All Manuals Search And Download.
BEFORE YOU BEGIN
®
Thank you for selecting the revolutionary PROFORM
ing this manual, please see the front cover of this man-
ual. To help us assist you, please note the product
model number and serial number before contacting us.
The model number and the location of the serial num-
ber decal are shown on the front cover of this manual.
8.5 ZT treadmill. The 8.5 ZT treadmill offers an impres-
sive selection of features designed to make your work-
outs at home more enjoyable and effective. And when
youʼre not exercising, the unique treadmill can be
folded up, requiring less than half the floor space of
other treadmills.
Before reading further, please review the drawing
below and familiarize yourself with the labeled parts.
For your benefit, read this manual carefully before
using the treadmill. If you have questions after read-
Tray
Console
Pulse Sensor
Handrail
Upright
Key/Clip
Reset/Off
Walking Belt
Foot Rail
Circuit Breaker
Power Cord
Platform Cushion
Idler Roller
Adjustment Bolts
5
Download from Www.Somanuals.com. All Manuals Search And Download.
ASSEMBLY
To hire an authorized service technician to assemble the treadmill, call 1-800-445-2480.
Assembly requires two persons. Set the treadmill in a cleared area and remove all packing materials. Do not
dispose of the packing materials until assembly is completed. Note: The underside of the treadmill walking
belt is coated with high-performance lubricant. During shipping, some lubricant may be transferred to the top of
the walking belt or the shipping carton. This is normal and does not affect treadmill performance. If there is lubri-
cant on top of the walking belt, simply wipe off the lubricant with a soft cloth and a mild, non-abrasive cleaner.
Assembly requires the included hex keys and your own Phillips screwdriver
adjustable wrench , needlenose pliers , and scissors
,
.
Use the drawings below to identify the assembly hardware. The number in parentheses below each drawing is
the key number of the part, from the PART LIST near the end of this manual. The number after the parentheses
is the quantity needed for assembly. Note: If a part is not in the hardware kit, check to see if it is preattached
to one of the parts to be assembled. To avoid damaging plastic parts, do not use power tools for assem-
bly. Extra hardware may be included.
1/4" Star
5/16" Star
3/8" Nut (11)–3
3/8" Star
Washer (14)–2
Washer (13)–4
Base Foot Spacer
(89)–2
Washer (12)–4
#8 x 3/4" Screw
(1)–4
#8 x 1" Tek Screw
(4)–4
Bolt Spacer (81)–4
3/8" x 1 3/4" Bolt (8)–1
5/16" x 1" Bolt (6)–6
3/8" x 2" Bolt (7)–3
3/8" x 4" Bolt (9)–4
1/4" x 1 1/4" Bolt (10)–2
6
Download from Www.Somanuals.com. All Manuals Search And Download.
1. Make sure that the power cord is unplugged.
1
A
B
With the help of a second person, carefully tip
the treadmill onto its left side. Partially fold the
Frame (51) so that the treadmill is more stable;
do not fully fold the Frame yet.
Hole
79
87
84
Remove and discard the indicated bolts (A) and
the shipping bracket (B).
4
Cut the shipping tie securing the Upright Wire
(79) to the Base (87). Locate the plastic tie in
the indicated hole in the Base, and use the tie to
pull the Upright Wire out of the hole.
89
51
84
4
Attach two Base Feet (84) to the Base (87) in the
locations shown with two Base Foot Spacers
(89) and two #8 x 1" Tek Screws (4).
84
Then, attach the other two Base Feet (84) with
two #8 x 1" Tek Screws (4).
4
84
4
89
2. Attach a Wheel (88) to the Base (87) with a 3/8"
x 2" Bolt (7) and a 3/8" Nut (11). Do not over-
tighten the Nut; the Wheel must turn freely.
2
83
Press a Base Cap (83) into the Base (87).
7
87
88
11
7
Download from Www.Somanuals.com. All Manuals Search And Download.
3. Identify the Right Upright (80) and the Right
Upright Spacer (82), which are marked with
“Right” stickers.
3
80
Insert the Upright Wire (79) through the Right
Upright Spacer (82) as shown. Set the Right
Upright Spacer on the Base (87).
79
Wire Tie
79
82
Have a second person hold the Right Upright
(80) near the Base (87). See the inset drawing.
Tie the wire tie in the Right Upright securely
around the end of the Upright Wire (79). Then,
pull the other end of the wire tie until the Upright
Wire is routed completely through the Right
Upright.
87
80
Wire
Tie
79
4. Hold a Bolt Spacer (81) inside the lower end of
the Right Upright (80). Insert a 3/8" x 4" Bolt (9)
with a 3/8" Star Washer (12) into the Right
Upright and the Bolt Spacer. Repeat this step
with a second Bolt Spacer (81), 3/8" x 4" Bolt
(9), and 3/8" Star Washer (12).
4
9
80
12
79
Hold the Right Upright (80) against the Right
Upright Spacer (82). Be careful not to pinch
the Upright Wire (79). Tighten the 3/8" x 4"
Bolts (9) until the heads of the Bolts touch the
Upright; do not fully tighten the Bolts yet.
81
81
82
8
Download from Www.Somanuals.com. All Manuals Search And Download.
5. With the help of a second person, carefully tip
the treadmill onto its right side. Partially fold the
Frame (51) so that the treadmill is more stable;
do not fully fold the Frame yet.
5
B
A
Remove and discard the indicated bolts (A) and
the shipping bracket (B).
Attach a Wheel (88) to the Base (87) with a 3/8"
x 2" Bolt (7) and a 3/8" Nut (11). Do not over-
tighten the Nut; the Wheel must turn freely.
7
51
87
88
11
6. Press a Base Cap (83) into the Base (87).
6
Hold a Bolt Spacer (81) inside the lower end of
the Left Upright (75). Insert a 3/8" x 4" Bolt (9)
with a 3/8" Star Washer (12) into the Left
Upright and the Bolt Spacer. Repeat this step
with a second Bolt Spacer (81), 3/8" x 4" Bolt
(9), and 3/8" Star Washer (12).
9
75
12
86
81
Hold the Left Upright Spacer (86) and the Left
Upright (75) against the Base (87). Tighten the
3/8" x 4" Bolts (9) until the heads of the Bolts
touch the Upright; do not fully tighten the
Bolts yet.
81
87
83
With the help of a second person, tip the tread-
mill so that the Base (87) is flat on the floor.
9
Download from Www.Somanuals.com. All Manuals Search And Download.
7. Set the console assembly face down on a soft
surface to avoid scratching the console assem-
bly. Hold the Right Handrail (104) near the con-
sole assembly. Next, insert the console wire into
the large hole in the Right Handrail and pull it
out of the top as shown. If necessary, use
7
Console
Wire
1
104
needlenose pliers to pull the console wire out.
Attach the Right Handrail (104) and the Left
Handrail (not shown) with four #8 x 3/4" Screws
(1) (only two are shown). Make sure that no
wires are pinched. Start all four Screws be-
fore tightening any of them; do not over-
tighten the Screws.
Console
Assembly
8. Start a 1/4" x 1 1/4" Bolt (10) with a 1/4" Star
Washer (14) into the bracket and the Crossbar
(102) on each side of the console assembly (only
one side is shown). Do not fully tighten the
Bolts yet.
8
Console
Wire
Wire
Tie
Plastic Tie
10
14
Remove the wire tie from the console wire and
the plastic ties (only one side is shown). If neces-
sary, press the Cage Nuts (74) back into place
(only one is shown).
Bracket
74
Console
Assembly
102
10
Download from Www.Somanuals.com. All Manuals Search And Download.
9. Have a second person hold the console assem-
bly near the Right Upright (80) and the Left
Upright (not shown). Connect the Upright Wire
(79) to the console wire. See the inset draw-
ing. The connectors should slide together
easily and snap into place. If they do not, turn
one connector and try again. IF THE CONNEC-
TORS ARE NOT CONNECTED PROPERLY,
THE CONSOLE MAY BE DAMAGED WHEN
THE POWER IS TURNED ON. Then, remove
the wire tie from the Upright Wire.
9
Console
Assembly
Console
Wire
Set the console assembly on the Right Upright
(80) and the Left Upright (not shown). Be care-
ful not to pinch the wires.
79
Console
Wire
Wire
Tie
80
79
10. Attach the console assembly with six 5/16" x 1"
Bolts (6) and four 5/16" Star Washers (13) (only
one side is shown).
10
Console
Assembly
See steps 4 and 6. Tighten the 3/8" x 4" Bolts
(9).
6
13
13
6
11
Download from Www.Somanuals.com. All Manuals Search And Download.
11. If necessary, press the Left Tray (94) and the
Right Tray (103) into the Console Back (98).
11
94
103
See step 8. Firmly tighten the two 1/4" x 1 1/4"
Bolts (10).
98
12. Raise the Frame (51) to the position shown.
Have a second person hold the Frame until
this step is completed.
12
Orient the Storage Latch (48) so that the large
barrel and the Latch Knob (49) are oriented as
shown.
51
Attach the upper end of the Storage Latch (48)
to the bracket on the Frame (51) with a 3/8" x 2"
Bolt (7) and a 3/8" Nut (11).
11
7
48
49
Attach the lower end of the Storage Latch (48) to
the Base (87) with a 3/8" x 1 3/4" Bolt (8). Note:
It may be necessary to move the Frame (51)
back and forth to align the Storage Latch with
the Base.
Large
Barrel
Lower the Frame (51) (see HOW TO LOWER
THE TREADMILL FOR USE on page 21).
87
8
13. Make sure that all parts are properly tightened before you use the treadmill. If there are sheets of clear
plastic on the treadmill decals, remove the plastic. To protect the floor or carpet, place a mat under the tread-
mill. Note: Extra hardware may be included. Keep the included hex keys in a secure place; one of the hex
keys is used to adjust the walking belt (see pages 23 and 24).
12
Download from Www.Somanuals.com. All Manuals Search And Download.
OPERATION AND ADJUSTMENT
THE PRE-LUBRICATED WALKING BELT
tric shock. This product is equipped with a cord having
an equipment-grounding conductor and a grounding
plug. Plug the power cord into a surge suppressor,
and plug the surge suppressor into an appropriate
outlet that is properly installed and grounded in
accordance with all local codes and ordinances.
IMPORTANT: The treadmill is not compatible with
GFCI-equipped outlets.
Your treadmill features a walking belt coated with high-
performance lubricant. IMPORTANT: Never apply sil-
icone spray or other substances to the walking
belt or the walking platform. Such substances will
deteriorate the walking belt and cause excessive
wear.
HOW TO PLUG IN THE POWER CORD
This product is for use on a nominal 120-volt circuit,
and has a grounding plug that looks like the plug illus-
trated in drawing 1 below. A temporary adapter that
looks like the adapter illustrated in drawing 2 may be
used to connect the surge suppressor to a 2-pole
receptacle as shown in drawing 2 if a properly
grounded outlet is not available.
DANGER:
Improper connection
of the equipment-grounding conductor can
result in an increased risk of electric shock.
Check with a qualified electrician or service-
man if you are in doubt as to whether the
product is properly grounded. Do not modify
the plug provided with the product—if it will
not fit the outlet, have a proper outlet
1
Grounded Outlet Box
Surge Suppressor
Grounding Pin
installed by a qualified electrician.
Your treadmill, like any other type of sophisticated
electronic equipment, can be seriously damaged by
sudden voltage changes in your homeʼs power.
Voltage surges, spikes, and noise interference can
result from weather conditions or from other appliances
being turned on or off. To decrease the possibility of
your treadmill being damaged, always use a surge
suppressor with your treadmill (see drawing 1 at
the right). To purchase a surge suppressor, see
your local PROFORM dealer or call the telephone
number on the front cover of this manual and order
part number 146148, or see your local electronics
store.
Grounding Pin
Grounded Outlet
Grounding Plug
2
Grounded Outlet Box
Adapter
Surge Suppressor
Use only a single-outlet surge suppressor that is
UL 1449 listed as a transient voltage surge sup-
pressor (TVSS). The surge suppressor must have a
UL suppressed voltage rating of 400 volts or less
and a minimum surge dissipation of 450 joules.
The surge suppressor must be electrically rated for
120 volts AC and 15 amps. There must be a moni-
toring light on the surge suppressor to indicate
whether it is functioning properly. Failure to use a
properly functioning surge suppressor could result
in damage to the control system of the treadmill. If
the control system is damaged, the walking belt
may slow, accelerate, or stop unexpectedly, which
may result in a fall and serious injury.
Lug
Metal Screw
Grounding Plug
The temporary adapter should be used only until a
properly grounded outlet (drawing 1) can be installed
by a qualified electrician.
The green-colored rigid ear, lug, or the like extending
from the adapter must be connected to a permanent
ground such as a properly grounded outlet box cover.
Whenever the adapter is used it must be held in place
by a metal screw. Some 2-pole receptacle outlet box
covers are not grounded. Contact a qualified elec-
trician to determine if the outlet box cover is
grounded before using an adapter.
This product must be grounded. If it should malfunc-
tion or break down, grounding provides a path of least
resistance for electric current to reduce the risk of elec-
13
Download from Www.Somanuals.com. All Manuals Search And Download.
CONSOLE DIAGRAM
Compatible Music Port for iPod
Navigation Buttons
FEATURES OF THE CONSOLE
out. iFit cards are available separately. To purchase
the telephone number on the front cover of this
manual. iFit cards are also available at select
The treadmill console offers an impressive array of
features designed to help you get the most from your
workouts. When the manual mode of the console is se- stores.
lected, the speed and incline of the treadmill can be
changed with the touch of a button. As you exercise,
the console will display continuous exercise feedback.
You can even measure your heart rate using the built-
in handgrip pulse sensor.
You can even listen to your favorite workout music or
audio books with the consoleʼs premium stereo sound
system while you get in shape. This treadmill has been
designed specifically to work with iPod and has been
certified by the developer to meet Apple performance
standards.
In addition, the console features fifteen preset work-
outs—five weight loss, five performance, and five aero-
bic workouts. Each workout automatically controls the
speed and incline of the treadmill as it guides you
through an effective exercise session.
To turn on the power, see page 15. To use the man-
ual mode, see page 15. To use a preset workout,
see page 17. To use an iFit workout, see page 18.
To use the information mode, see page 19. To use
the stereo sound system, see page 19.
The console also features the new iFit interactive
workout system. The iFit system enables the console
to accept iFit interactive workout cards containing
workouts designed to help you achieve specific fitness
goals. For example, lose unwanted pounds with the 8-
week weight loss workout, or train for a long-distance
run with the marathon workout. iFit workouts automati-
cally control the treadmill while the voice of a personal
trainer coaches you through every step of your work-
Note: The console can display speed and distance in
either miles or kilometers. To find out which unit of
measurement is selected or to change the unit of mea-
surement, see THE INFORMATION MODE on page
19. Note: For simplicity, all instructions in this section
refer to miles.
14
Download from Www.Somanuals.com. All Manuals Search And Download.
HOW TO TURN ON THE POWER
HOW TO USE THE MANUAL MODE
1. Insert the key into the console.
See HOW TO TURN ON THE POWER to the left.
2. Select the manual mode.
IMPORTANT: If the treadmill has been exposed to
cold temperatures, allow it to warm to room tem-
perature before turning on the power. If you do not
do this, you may damage the console displays or
other electrical components.
Plug in the power cord
(see page 13). Next, lo-
cate the reset/off circuit
When the key is
inserted, the man-
ual mode will be
breaker on the treadmill
frame near the power
selected. If a
Reset
workout has been
cord. Switch the circuit
breaker to the reset position.
selected, reselect
the manual mode
by removing the key and then reinserting it.
IMPORTANT: The console features a display demo
mode, designed to be used if the treadmill is dis-
played in a store. If the displays light as soon as
you plug in the power cord and switch the reset/off
circuit breaker to the reset position, the demo
mode is turned on. To turn off the demo mode,
hold down the Stop button for a few seconds. If the
displays remain lit, see THE INFORMATION MODE
on page 19 to turn off the demo mode.
3. Start the walking belt.
To start the walking belt, press the Start button, the
Speed increase button, or one of the speed but-
tons numbered 1 through 10.
If you press the Start button or the Speed increase
button, the walking belt will begin to move at 1
mph. As you exercise, change the speed of the
walking belt as desired by pressing the Speed in-
crease and decrease buttons. Each time you press
the Speed increase or decrease button, the speed
setting will change by 0.1 mph; if you hold down
the button, the speed setting will change in incre-
ments of 0.5 mph. Note: After you press the but-
tons, it may take a moment for the walking belt to
reach the selected speed setting.
Next, stand on the foot
rails of the treadmill. Find
the clip attached to the key
(see the drawing to the
right) and slide the clip
onto the waistband of your
clothes. Then, insert the
Clip
Key
key into the console. After a moment, the displays will
light. IMPORTANT: In an emergency situation, the
key can be pulled from the console, causing the
walking belt to slow to a stop. Test the clip by
carefully taking a few steps backward; if the key is
not pulled from the console, adjust the position of
the clip.
If you press one of the speed buttons numbered 1
through 10, the walking belt will gradually increase
in speed until it reaches the selected speed setting.
To stop the walking belt, press the Stop button. To
restart the walking belt, press the Start button, the
Speed increase button, or one of the numbered
speed buttons.
IMPORTANT: If there are sheets of clear plastic on
the console, remove the plastic. To prevent dam-
age to the walking platform, wear clean athletic
shoes while using the treadmill. The first time you
use the treadmill, observe the alignment of the
walking belt, and center the walking belt if neces-
sary (see page 24).
4. Change the incline of the treadmill as desired.
To change the incline of the treadmill, press the
Incline increase and decrease buttons. Each time
you press the Incline increase or decrease button,
the incline will change by 0.5 percent. To change
the incline quickly, press one of the incline buttons
numbered 0 through 10. Note: After you press the
Incline buttons, it may take a moment for the tread-
mill to reach the selected incline setting.
15
Download from Www.Somanuals.com. All Manuals Search And Download.
5. Select a display mode and monitor your
progress with the display.
6. Measure your heart rate if desired.
Before using the
handgrip pulse
sensor, remove
the clear plastic
film from the
When the manual mode is selected, the console
offers three display modes. The display mode that
you select will determine which workout informa-
tion is shown. Press the Display button repeatedly
to select the desired display mode.
metal contacts. In
addition, make
sure that your
Contacts
As you walk or run on the treadmill, the display can
show the following workout information:
hands are clean.
• The speed of the walking belt.
To measure your heart rate, stand on the foot
rails and hold the metal contacts—avoid moving
your hands. When your pulse is detected, your
heart rate will be shown. For the most accurate
heart rate reading, continue to hold the con-
tacts for about 15 seconds.
• Your walking or running pace, in minutes per
mile or minutes per kilometer.
• The approximate number of calories you have
burned.
7. Turn on the fan if desired.
• The elapsed time.
The fan features high, low, and auto speed set-
tings. Press the Fan button repeatedly to select a
fan speed or to turn off the fan. When the auto
mode is selected, the speed of the fan will auto-
matically increase and decrease as the speed of
the walking belt increases and decreases. Note: If
the fan is on when the walking belt is stopped, the
fan will turn off automatically after a few minutes.
• The distance that you have walked or run.
• The number of laps you have completed. Each
lap represents 1/4 mile (400 meters).
• The incline setting of the treadmill whenever the
incline setting changes.
• Your heart rate. Note: Your heart rate can be
displayed only while you use the handgrip pulse
sensor.
8. When you are finished exercising, remove the
key from the console.
Step onto the foot rails, press the Stop button, and
adjust the incline of the treadmill to the lowest
setting. The incline must be at the lowest set-
ting or you may damage the treadmill when you
fold it to the storage position. Next, remove the
key from the console and put it in a secure place.
• The display can also show an animation of a
road.
Regardless of which display mode you select, the
speed or incline setting will appear in the display for
a few seconds each time you change the setting.
When you are finished using the treadmill, switch
the reset/off circuit breaker to the off position and
unplug the power cord. IMPORTANT: If you do
not do this, the treadmillʼs electrical compo-
nents may wear prematurely.
You can change the volume level by pressing the
Volume increase and decrease buttons.
To reset the console, press the Stop button, re-
move the key, and then reinsert the key.
16
Download from Www.Somanuals.com. All Manuals Search And Download.
HOW TO USE A PRESET WORKOUT
1. Insert the key into the console.
A profile of the
speed settings of
the workout will
appear in the
See HOW TO TURN ON THE POWER on page
15.
display. A small
arrow below the
profile will indi-
cate your progress.
2. Select one of the preset workouts.
To select a
At the end of the first one-minute segment of the
workout, a series of tones will sound. If a different
speed setting and/or incline setting is programmed
for the second segment, the speed setting and/or
incline setting will flash in the display for a moment
to alert you. The treadmill will then automatically
adjust to the speed and incline settings for the sec-
ond segment.
weight loss
workout or a
performance
workout, press
the Weight Loss
Workouts but-
ton or the Performance Workouts button. Profiles
of the speed settings of the workouts will appear in
the display. To select an aerobic workout, press
the Weight Loss Workouts button and then press
the down Navigation button until the aerobic pro-
files appear in the display. Use the Navigation but-
tons to highlight the desired profile. The maximum
speed setting and maximum incline setting of the
workout will be shown. Press Enter to select the
workout.
The workout will continue in this way until the small
arrow reaches the right end of the profile and the
last segment ends. The walking belt will then slow
to a stop.
If the speed or incline setting is too high or too low
at any time during the workout, you can override
the setting by pressing the speed or incline but-
tons; however, when the next segment begins,
the treadmill will automatically adjust to the
speed and incline settings for the next
segment.
As each preset
workout is se-
lected, the max-
imum speed
setting and the
To stop the workout at any time, press the Stop
button. To restart the workout, press the Start but-
ton. The walking belt will begin to move at 1 mph.
When the next segment of the workout begins, the
treadmill will automatically adjust to the speed and
incline settings for the next segment.
maximum in-
cline setting of
the workout will flash in the displays for a few sec-
onds. The workout duration and a profile of the
speed settings of the workout will appear in the dis-
play.
4. Select a display mode and monitor your
progress with the display.
3. Start the workout.
Press the Start button or the Speed increase but-
ton to start the workout. A moment after you press
the button, the treadmill will automatically adjust to
the first speed and incline settings for the workout.
Hold the handrails and begin walking.
See step 5 on page 16.
5. Measure your heart rate if desired.
See step 6 on page 16.
Each workout is divided into one-minute segments.
One speed setting and one incline setting are pro-
grammed for each segment. Note: The same
speed and/or incline setting may be programmed
for consecutive segments.
6. Turn on the fan if desired.
See step 7 on page 16.
7. When you are finished exercising, remove the
key from the console.
See step 8 on page 16.
17
Download from Www.Somanuals.com. All Manuals Search And Download.
HOW TO USE AN IFIT WORKOUT
the button, the treadmill will automatically adjust to
the first speed and incline settings for the workout.
Hold the handrails and begin walking.
or call the telephone number on the front cover of this
manual. iFit cards are also available at select stores.
During the workout, the voice of a personal trainer
will guide you through the workout. You can select
an audio setting for your personal trainer (see THE
INFORMATION MODE on page 19).
1. Insert the key into the console.
See HOW TO TURN ON THE POWER on page
15.
If the speed or incline setting for the current seg-
ment is too high or too low, you can manually over-
ride the setting by pressing the Speed or Incline
buttons; however, when the next segment be-
gins, the treadmill will automatically adjust to
the speed and incline settings for the next seg-
ment.
2. Insert an iFit card and select a workout.
To use an iFit workout, insert an iFit card into the
iFit slot; make sure that the iFit card is oriented so
the metal contacts are face-down and are inserted
into the iFit slot.
To stop the workout at any time, press the Stop
button. To restart the workout, press the Start but-
ton or the Speed increase button. The walking belt
will begin to move at 1 mph. When the next seg-
ment of the workout begins, the treadmill will auto-
matically adjust to the speed and incline settings
for the next segment.
iFit Slot
iFit Card
4. Select a display mode and monitor your
progress with the display.
See step 5 on page 16.
5. Measure your heart rate if desired.
See step 6 on page 16.
Next, select an iFit workout by pressing the iFit in-
crease and decrease buttons next to the iFit slot.
When an iFit workout is selected, the maximum
speed setting and the maximum incline setting of
the workout will flash in the displays for a few sec-
onds. The workout duration and a profile of the
speed settings of the workout will appear in the dis-
play.
6. Turn on the fan if desired.
See step 7 on page 16.
Each iFit workout is divided into several one-
minute segments. One speed setting and one in-
cline setting are programmed for each segment.
Note: The same speed and/or incline setting may
be programmed for consecutive segments.
7. When you are finished exercising, remove the
key from the console.
See step 8 on page 16.
CAUTION: Always remove iFit cards from the
iFit slot when you are not using them.
3. Start the workout.
Press the Start button or the Speed increase but-
ton to start the workout. A moment after you press
18
Download from Www.Somanuals.com. All Manuals Search And Download.
THE INFORMATION MODE
and insert the key into the console. However, when
you remove the key, the displays will remain lit, al-
though the buttons will not function. If the demo mode
is turned on, the word ON will appear in the display
while the information mode is selected. To turn on or
off the demo mode, press the Speed decrease button.
The console features a userʼs mode that allows you to
choose an audio setting for your iFit workouts. The
userʼs mode also keeps track of the total number of
miles that the walking belt has moved and the total
number of hours that the treadmill has been operated.
You can also select miles or kilometers as the unit of
measurement and turn on and turn off the demo mode.
To exit the information mode, remove the key from the
console.
To select the information mode, hold down the Stop
button while inserting the key into the console and then HOW TO USE THE STEREO SOUND SYSTEM
release the Stop button. When the information mode is
selected, the following information will be shown:
This treadmill has been designed specifically to work
with iPod and has been certified by the developer to
meet Apple performance standards. To play music or
audio books through the consoleʼs stereo speakers,
you must connect your iPod, MP3 player, CD player,
or other personal audio player to the console through
the audio jack or through the compatible music port for
iPod. The music port will charge your iPod while you
use it.
To use the audio wire, locate the audio wire and plug it
into the audio jack near the speakers. Then plug the
audio wire into a jack on your MP3 player, CD player,
or other personal audio player. Make sure that the
audio wire is fully plugged in.
You can select an audio setting for your personal
trainer if desired. When you use an iFit card, a per-
sonal trainer will guide you through your workouts. If
you select the ON setting, the personal trainer will give
you detailed instructions. If you select the OFF setting,
your personal trainer will simply guide you through
your iFit workouts. To change the audio setting, press
the Incline decrease button.
To use the compatible music port for iPod, you need
an iFit universal iPod connector (not included). To pur-
chase an iFit universal iPod connector, please call
the telephone number on the front cover of this
manual. Plug one end into the music port near the
speakers and the other end into your iPod. Make sure
that the iFit universal iPod connector is fully
plugged in.
The display will show the total number of hours the
treadmill has been used. The display will also show the
total number of miles (or kilometers) that the walking
belt has moved.
The word ENGLISH for miles or METRIC for kilome-
ters will appear in the display. Press the Speed in-
crease button to change the unit of measurement if de-
sired.
Next, press the Play button on your iPod, MP3 player,
CD player, or other personal audio player. Adjust the
volume on your personal audio player or press the
Volume increase and decrease buttons on the con-
sole.
Note: The console features a display demo mode, de-
signed to be used if the treadmill is displayed in a
store. While the demo mode is turned on, the console
will function normally when you plug in the power cord,
switch the reset/off circuit breaker to the reset position,
If you are using a personal CD player and the CD
skips, set the CD player on the floor or another flat sur-
face and not on the console.
19
Download from Www.Somanuals.com. All Manuals Search And Download.
HOW TO FOLD AND MOVE THE TREADMILL
HOW TO FOLD THE TREADMILL FOR STORAGE
Before folding the treadmill, adjust the incline to the
lowest position. If you do not do this, you may damage the
treadmill when you fold it. Remove the key and unplug the
power cord. CAUTION: You must be able to safely lift 45
Frame
lbs. (20 kg) to raise, lower, or move the treadmill.
1. Hold the metal frame firmly in the location shown by
the arrow at the right. CAUTION: To decrease the pos-
sibility of injury, do not lift the frame by the plastic
foot rails. Make sure to bend your legs and keep your
back straight as you raise the frame. Raise the frame
about halfway to the vertical position.
2. Raise the frame until the latch knob locks into the storage
position. Make sure that the latch knob is locked in the
storage position.
To protect the floor or carpet from damage, place a
mat under the treadmill. Keep the treadmill out of di-
rect sunlight. Do not leave the treadmill in the storage
position in temperatures above 85° F (30° C).
Frame
Latch Knob
HOW TO MOVE THE TREADMILL
Before moving the treadmill, convert the treadmill to the stor-
age position as described above. Make sure that the latch
knob is locked in the storage position.
Handrail
Frame
1. Hold a handrail and the frame and place one foot against
one of the wheels.
2. Tip the treadmill back until it rolls freely on the wheels.
Carefully move the treadmill to the desired location. Never
move the treadmill without tipping it back. To reduce
the risk of injury, use extreme caution while moving
the treadmill. Do not attempt to move the treadmill
over an uneven surface.
Wheel
3. Place one foot against a wheel, and carefully lower the
treadmill until it is resting in the storage position.
20
Download from Www.Somanuals.com. All Manuals Search And Download.
HOW TO LOWER THE TREADMILL FOR USE
1. Hold the upper end of the treadmill with your right hand.
Pull the latch knob to the left and hold it. It may be neces-
sary to push the frame forward as you pull the knob to
the left. Pivot the frame downward and release the latch
knob.
Latch Knob
2. Hold the metal frame firmly with both hands and lower
it to the floor. CAUTION: Do not grip only the plastic
foot rails or drop the frame to the floor. Bend your
legs and keep your back straight.
Frame
21
Download from Www.Somanuals.com. All Manuals Search And Download.
TROUBLESHOOTING
Most treadmill problems can be solved by following the simple steps below. Find the symptom that
applies, and follow the steps listed. If further assistance is needed, see the front cover of this manual.
PROBLEM: The power does not turn on
SOLUTION: a. Make sure that the power cord is plugged into a surge suppressor, and that the surge suppressor
is plugged into a properly grounded outlet (see page 13). Use only a single-outlet surge suppres-
sor that meets all of the specifications described on page 13. IMPORTANT: The treadmill is not
compatible with GFCI-equipped outlets.
b. After the power cord has been plugged in, make sure that the key is inserted into the console.
c. Check the reset/off circuit breaker located on the
c
treadmill frame near the power cord. If the switch
protrudes as shown, the circuit breaker has
tripped. To reset the circuit breaker, wait for five
Tripped
Reset
minutes and then press the switch back in.
PROBLEM: The power turns off during use
SOLUTION: a. Check the reset/off circuit breaker (see the drawing above). If the circuit breaker has tripped, wait
for five minutes and then press the switch back in.
b. Make sure that the power cord is plugged in. If the power cord is plugged in, unplug it, wait for
five minutes, and then plug it back in.
c. Remove the key from the console. Reinsert the key into the console.
d. If the treadmill still will not run, please see the front cover of this manual.
PROBLEM: The console displays remain lit when you remove the key from the console
SOLUTION: a. The console features a display demo mode, designed to be used if the treadmill is displayed in a
store. If the displays remain lit when you remove the key, the demo mode is turned on. To turn off
the demo mode, hold down the Stop button for a few seconds. If the displays are still lit, see THE
INFORMATION MODE on page 19 to turn off the demo mode.
PROBLEM: The displays of the console do not function properly
SOLUTION: a. Remove the key from the console and UNPLUG
THE POWER CORD. With the help of a second
person, carefully tip down the Uprights (75, 80).
There may be three #8 x 2" Screws (16) in the bot-
tom of the Belly Pan (73). If there are, remove them.
Note: A Phillips screwdriver with a shaft at least 5
in. (13 cm) long is required.
a
75
73
16
80
Then, raise the Uprights (75, 80).
16
22
Download from Www.Somanuals.com. All Manuals Search And Download.
Remove the three #8 x 3/4" Screws (1) and care-
fully pivot the Motor Hood (60) off.
1
60
Locate the Reed Switch (71) and the Magnet (45)
on the left side of the Pulley (46). Turn the Pulley
until the Magnet is aligned with the Reed Switch.
Make sure that the gap between the Magnet and
the Reed Switch is about 1/8 in. (3 mm). If nec-
essary, loosen the 3/4" Screw (17), move the Reed
Switch slightly, and then retighten the Screw.
Reattach the Motor Hood (not shown). Reattach
the #8 x 2" Screws (not shown) if necessary. Run
the treadmill for a few minutes to check for a cor-
rect speed reading.
1/8 in.
17
45
46
71
Top
View
PROBLEM: The incline of the treadmill does not change correctly
SOLUTION: a. With the key in the console, press one of the Incline buttons. While the incline is changing, re-
move the key. After a few seconds, re-insert the key. The treadmill will automatically rise to the
maximum incline level and then return to the minimum level. This will recalibrate the incline system.
PROBLEM: The walking belt slows when walked on
SOLUTION: a. Use only a single-outlet surge suppressor that meets all of the specifications described on page 13.
b. If the walking belt is overtightened, treadmill perfor-
b
mance may decrease and the walking belt may be-
2–3 in.
come damaged. Remove the key and UNPLUG
THE POWER CORD. Using the hex key, turn both
idler roller bolts counterclockwise, 1/4 of a turn.
When the walking belt is properly tightened, you
should be able to lift each edge of the walking belt
2 to 3 in. (5 to 7 cm) off the walking platform. Be
careful to keep the walking belt centered. Then,
plug in the power cord, insert the key, and run the
Idler Roller Bolts
treadmill for a few minutes. Repeat until the walking
belt is properly tightened.
c. If the walking belt still slows when walked on, see the front cover of this manual.
23
Download from Www.Somanuals.com. All Manuals Search And Download.
PROBLEM: The walking belt is off-center or slips when walked on
SOLUTION: a. If the walking belt is off-center, first remove the
key and UNPLUG THE POWER CORD. If the
walking belt has shifted to the left, use the hex
key to turn the left idler roller bolt clockwise 1/2 of a
turn; if the walking belt has shifted to the right,
turn the bolt counterclockwise 1/2 of a turn. Be
careful not to overtighten the walking belt. Then,
plug in the power cord, insert the key, and run the
treadmill for a few minutes. Repeat until the walk-
ing belt is centered.
a
b. If the walking belt slips when walked on, first re-
move the key and UNPLUG THE POWER CORD.
Using the hex key, turn both idler roller bolts clock-
wise, 1/4 of a turn. When the walking belt is cor-
rectly tightened, you should be able to lift each
edge of the walking belt 2 to 3 in. (5 to 7 cm) off
the walking platform. Be careful to keep the walk-
ing belt centered. Then, plug in the power cord, in-
sert the key, and carefully walk on the treadmill for
a few minutes. Repeat until the walking belt is
properly tightened.
b
24
Download from Www.Somanuals.com. All Manuals Search And Download.
EXERCISE GUIDELINES
Burning Fat—To burn fat effectively, you must exer-
cise at a low intensity level for a sustained period of
time. During the first few minutes of exercise, your
body uses carbohydrate calories for energy. Only after
the first few minutes of exercise does your body begin
to use stored fat calories for energy. If your goal is to
burn fat, adjust the intensity of your exercise until your
heart rate is near the lowest number in your training
zone. For maximum fat burning, exercise with your
heart rate near the middle number in your training
zone.
WARNING:
Before beginning this
or any exercise program, consult your physi-
cian. This is especially important for persons
over age 35 or persons with pre-existing
health problems.
The pulse sensor is not a medical device.
Various factors may affect the accuracy of
heart rate readings. The pulse sensor is in-
tended only as an exercise aid in determining
heart rate trends in general.
Aerobic Exercise—If your goal is to strengthen your
cardiovascular system, you must perform aerobic exer-
cise, which is activity that requires large amounts of
oxygen for prolonged periods of time. For aerobic ex-
ercise, adjust the intensity of your exercise until your
heart rate is near the highest number in your training
zone.
These guidelines will help you to plan your exercise
program. For detailed exercise information, obtain a
reputable book or consult your physician. Remember,
proper nutrition and adequate rest are essential for
successful results.
WORKOUT GUIDELINES
EXERCISE INTENSITY
Warming Up—Start with 5 to 10 minutes of stretching
and light exercise. A warm-up increases your body
temperature, heart rate, and circulation in preparation
for exercise.
Whether your goal is to burn fat or to strengthen your
cardiovascular system, exercising at the proper inten-
sity is the key to achieving results. You can use your
heart rate as a guide to find the proper intensity level.
The chart below shows recommended heart rates for
fat burning and aerobic exercise.
Training Zone Exercise—Exercise for 20 to 30 min-
utes with your heart rate in your training zone. (During
the first few weeks of your exercise program, do not
keep your heart rate in your training zone for longer
than 20 minutes.) Breathe regularly and deeply as you
exercise–never hold your breath.
Cooling Down—Finish with 5 to 10 minutes of stretch-
ing. Stretching increases the flexibility of your muscles
and helps to prevent post-exercise problems.
EXERCISE FREQUENCY
To find the proper intensity level, find your age at the
bottom of the chart (ages are rounded off to the near-
est ten years). The three numbers listed above your
age define your “training zone.” The lowest number is
the heart rate for fat burning, the middle number is the
heart rate for maximum fat burning, and the highest
number is the heart rate for aerobic exercise.
To maintain or improve your condition, complete three
workouts each week, with at least one day of rest be-
tween workouts. After a few months of regular exer-
cise, you may complete up to five workouts each
week, if desired. Remember, the key to success is to
make exercise a regular and enjoyable part of your
everyday life.
25
Download from Www.Somanuals.com. All Manuals Search And Download.
PART LIST—Model No. PFTL54509.0
To locate the parts listed below, see the EXPLODED DRAWING near the end of this manual.
R0110A
Key No. Qty.
Description
Key No. Qty.
Description
1
26
2
4
4
1
6
3
1
4
2
3
4
4
2
5
3
9
2
2
2
2
1
1
2
7
8
2
4
2
2
4
4
3
1
2
1
1
2
1
1
2
2
2
1
1
1
1
1
1
1
#8 x 3/4" Screw
#8 x 1/2" Screw
Console Fan Screw
#8 x 1" Tek Screw
Console Fan
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
85
86
87
88
89
90
91
92
93
94
95
96
97
98
99
100
1
1
1
1
1
2
1
1
1
1
1
1
3
1
1
1
1
1
1
1
1
1
1
2
1
1
1
1
1
1
4
1
2
4
2
1
1
2
2
2
6
6
1
1
1
1
1
1
2
4
Frame
2
Left Rear Foot
Idler Roller Ground Wire
Right Rear Foot
Idler Roller
3
4
5
6
5/16" x 1" Bolt
3/8" x 2" Bolt
Idler Roller Bracket
5/32" Hex Key
Hex Key
7
8
3/8" x 1 3/4" Bolt
3/8" x 4" Bolt
9
Hood Accent
Motor Hood
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
1/4" x 1 1/4" Bolt
3/8" Nut
Lift Frame
3/8" Star Washer
5/16" Star Washer
1/4" Star Washer
#8 x 3/4" Tek Screw
#8 x 2" Screw
3/4" Screw
Lift Frame Ground Wire
Wire Tie
Drive Belt
Drive Motor
Controller Ground Wire
Power Cord
5/16" x 1 1/2" Bolt
5/16" x 3 5/8" Bolt
3/8" x 1" Bolt
Power Cord Grommet
Reset/Off Circuit Breaker
Controller
Idler Roller Bolt
3/8" x 1 3/4" Incline Bolt
3/8" x 1 1/2" Bolt
3/8" x 3/4" Bolt
#8 x 1/2" Bright Screw
#12 x 1 1/4" Screw
Motor Bolt
Reed Switch
Reed Switch Clamp
Belly Pan
Cage Nut
Left Upright
Incline Motor
Incline Motor Spacer
Incline Motor Wire
Upright Wire
Right Upright
Bolt Spacer
Belt Guide Screw
1/4" Washer
1/4" Split Washer
3/8" Jam Nut
5/16" Flange Nut
Hood Clip
Right Upright Spacer
Base Cap
Access Door
Base Foot
Foot Rail Decal
Left Foot Rail
Caution Decal
Left Upright Spacer
Base
Warning Decal
Platform Cushion
Walking Platform
Walking Belt
Wheel
Base Foot Spacer
15 1/2" Wire Tie
Releaseable Tie
8" Tie
Belt Guide
Frame Cap
Frame Spacer
1/4" x 1" Bolt
Key Clip
Left Tray
Magnet
Audio Cable
Drive Roller/Pulley
Latch Cap
Console
Wire Tie
Storage Latch
Latch Knob
Console Back
#8 x 1 1/2" Screw
Handrail Cap
Right Foot Rail
26
Download from Www.Somanuals.com. All Manuals Search And Download.
Key No. Qty.
Description
Key No. Qty.
Description
101
102
103
1
1
1
Left Handrail
Crossbar
104
*
1
–
Right Handrail
Userʼs Manual
Right Tray
Note: Specifications are subject to change without notice. For information about ordering replacement parts, see
the back cover of this manual. *These parts are not illustrated.
27
Download from Www.Somanuals.com. All Manuals Search And Download.
EXPLODED DRAWING A—Model No. PFTL54509.0
R0110A
8
7
4
2
3
4
4
6
2
4
4
2
1
5
3
4
3
8
2
6
2
7
1
8
3
5
4
6
6
4
2
7
1
3
4
2
0
4
5
1
5
6
2
2
6
3
2
0
4
6
5
2
3
8
2
1
3
4
5
6
2
9
5
3
2
7
1
9
5
9
3
8
3
6
3
6
2
7
5
2
5
3
8
2
5
5
3
7
1
9
9
5
6
7
2
5
5
6
2
28
Download from Www.Somanuals.com. All Manuals Search And Download.
EXPLODED DRAWING B—Model No. PFTL54509.0
R0110A
1
33
1
33
1
33
60
59
27
61
25
20
62
64
25
63
25
65
20
66
25
2
71
67
15
70
15
17
72
68
69
15
15
16
73
16
16
29
Download from Www.Somanuals.com. All Manuals Search And Download.
EXPLODED DRAWING C—Model No. PFTL54509.0
R0110A
6
13
6
22
78
31
75
76
23
31
77
9
6
6
13
83
24
86
80
79
12
31
81
85
24
84
4
87
31
83
12
7
9
79
85
89
11
84
4
88
84
81
82
4
11
88
12
9
81
90
89
84
4
7
91
92
30
Download from Www.Somanuals.com. All Manuals Search And Download.
EXPLODED DRAWING D—Model No. PFTL54509.0
R0110A
5
96
3
95
3
94
1
1
1
1
98
93
1
1
34
1
100
1
1
103
1
1
1
1
102
14
74
101
10
1
100
100
1
1
14
97
10
1
104
74
100
31
Download from Www.Somanuals.com. All Manuals Search And Download.
ORDERING REPLACEMENT PARTS
To order replacement parts, please see the front cover of this manual. To help us assist you, be prepared to pro-
vide the following information when contacting us:
• the model number and serial number of the product (see the front cover of this manual)
• the name of the product (see the front cover of this manual)
• the key number and description of the replacement part(s) (see the PART LIST and the EXPLODED
DRAWING near the end of this manual)
LIMITED WARRANTY
IMPORTANT: You must register this product within 30 days of the purchase date to avoid added
ICON Health & Fitness, Inc. (ICON) warrants this product to be free from defects in workmanship and
material, under normal use and service conditions. The frame is warranted for a lifetime. The drive motor
is warranted for twenty-five (25) years from the date of purchase. Parts and labor are warranted for one
(1) year from the date of purchase.
This warranty extends only to the original purchaser. ICONʼs obligation under this warranty is limited to
repairing or replacing, at ICONʼs option, the product through one of its authorized service centers. All re-
pairs for which warranty claims are made must be preauthorized by ICON. If the product is shipped to a
service center, freight charges to and from the service center will be the customerʼs responsibility. For
replacement parts shipped while the product is under warranty, the customer will be responsible for a
minimal handling charge. For in-home service, the customer will be responsible for a minimal trip charge.
This warranty does not extend to any damage to a product caused by or attributable to freight damage,
abuse, misuse, improper or abnormal usage, or repairs not provided by an ICON authorized service cen-
ter; to products used for commercial or rental purposes or as store display models; or to products trans-
ported or purchased outside the US. No other warranty beyond that specifically set forth above is autho-
rized by ICON.
ICON is not responsible or liable for indirect, special, or consequential damages arising out of or in con-
nection with the use or performance of the product; damages with respect to any economic loss, loss of
property, loss of revenues or profits, loss of enjoyment or use, or costs of removal or installation; or other
consequential damages of whatsoever nature. Some states do not allow the exclusion or limitation of in-
cidental or consequential damages. Accordingly, the above limitation may not apply to you.
The warranty extended hereunder is in lieu of any and all other warranties, and any implied warranties of
merchantability or fitness for a particular purpose are limited in their scope and duration to the terms set
forth herein. Some states do not allow limitations on how long an implied warranty lasts. Accordingly, the
above limitation may not apply to you.
This warranty gives you specific legal rights. You may also have other rights that vary from state to state.
ICON Health & Fitness, Inc., 1500 S. 1000 W., Logan, UT 84321-9813
Part No. 294657 R0110A
Printed in China © 2010 ICON IP, Inc.
Download from Www.Somanuals.com. All Manuals Search And Download.
|