¨
Model No. PFTL79192
Serial No.
USER'S MANUAL
Find the serial number in the location
shown below. Write the serial number
in the space above for reference.
Serial Number Decal
QUESTIONS?
As a manufacturer, we are com-
mitted to providing complete
customer satisfaction. If you
have questions, or if there are
missing parts, we will guarantee
complete satisfaction through di-
rect assistance from our factory.
TO AVOID UNNECESSARY DE-
LAYS, PLEASE CALL DIRECT TO
OUR TOLL-FREE CUSTOMER
HOT LINE. The trained techni-
cians on our Customer Hot Line
will provide immediate assis-
tance, free of charge to you.
Patent Pending
CUSTOMER HOT LINE:
1-800-999-3756
Mon.ÐFri., 6 a.m.Ð6 p.m. MST
CAUTION
Visit our website at
Read all precautions and instruc-
tions in this manual before using
this equipment. Save this manual
for future reference.
new products, prizes,
fitness tips, and much more!
Download from Www.Somanuals.com. All Manuals Search And Download.
IMPORTANT PRECAUTIONS
WARNING:
To reduce the risk of burns, fire, electric shock, or injury to persons, read the
following important precautions and information before operating the treadmill.
1. It is the responsibility of the owner to ensure
that all users of this treadmill are adequately
informed of all warnings and precautions.
less in length. Do not use an extension cord.
12. Keep the power cord and the surge protector
away from heated surfaces.
2. Use the treadmill only as described in this
manual.
13. Never move the walking belt while the power
is turned off. Do not operate the treadmill if
the power cord or plug is damaged, or if the
treadmill is not working properly. (See
BEFORE YOU BEGIN on page 5 if the tread-
mill is not working properly.)
3. Place the treadmill on a level surface, with at
least eight feet of clearance behind it. Do not
place the treadmill on any surface that blocks
air openings. To protect the floor or carpet
from damage, place a mat under the treadmill.
14. Never start the treadmill while you are stand-
ing on the walking belt. Always hold the
handrails while using the treadmill.
4. Keep the treadmill indoors, away from mois-
ture and dust. Do not put the treadmill in a
garage or covered patio, or near water.
15. The treadmill is capable of high speeds.
Adjust the speed in small increments to avoid
sudden jumps in speed.
5. Do not operate the treadmill where aerosol
products are used or where oxygen is being
administered.
16. The pulse sensor is not a medical device.
Various factors, including the user's move-
ment, may affect the accuracy of heart rate
readings. The pulse sensor is intended only
as an exercise aid in determining heart rate
trends in general.
6. Keep children under the age of 12 and pets
away from the treadmill at all times.
7. The treadmill should not be used by persons
weighing more than 250 pounds.
8. Never allow more than one person on the
treadmill at a time.
17. Never leave the treadmill unattended while it
is running. Always remove the key, unplug
the power cord and move the on/off switch to
the off position when the treadmill is not in
use. (See the drawing on page 5 for the loca-
tion of the on/off switch.)
9. Wear appropriate exercise clothing when
using the treadmill. Do not wear loose cloth-
ing that could become caught in the treadmill.
Athletic support clothes are recommended for
both men and women. Always wear athletic
shoes. Never use the treadmill with bare feet,
wearing only stockings, or in sandals.
18. Do not attempt to raise, lower, or move the
treadmill until it is properly assembled. (See
ASSEMBLY on page 6, and HOW TO FOLD
AND MOVE THE TREADMILL on page 19.) You
must be able to safely lift 45 pounds (20 kg) in
order to raise, lower, or move the treadmill.
10. When connecting the power cord (see page 8),
plug the power cord into a surge protector (not
included) and plug the surge protector into a
grounded circuit capable of carrying 15 or
more amps. No other appliance should be on
the same circuit. Do not use an extension cord.
19. Do not change the incline of the treadmill by
placing objects under the treadmill.
20. When folding or moving the treadmill, make
sure that the storage latch is fully closed.
11. Use only a UL-listed surge protector, rated at
15 amps, with a 14-gauge cord of five feet or
3
Download from Www.Somanuals.com. All Manuals Search And Download.
21. When using iFit.com CDÕs and videos, an
electronic ÒchirpingÓ sound will alert you
when the speed and/or incline of the treadmill
is about to change. Always listen for the
ÒchirpÓ and be prepared for speed and/or in-
cline changes. In some instances, the speed
and/or incline may change before the per-
sonal trainer describes the change.
24. Inspect and tighten all parts of the treadmill
regularly.
25. Never insert or drop any object into any
opening.
26.
DANGER:
Always unplug the power
cord immediately after use, before cleaning
the treadmill, and before performing the main-
tenance and adjustment procedures de-
scribed in this manual. Never remove the
motor hood unless instructed to do so by an
authorized service representative. Servicing
other than the procedures in this manual
should be performed by an authorized service
representative only.
22. When using iFit.com CDÕs and videos, you
can manually override the speed and incline
settings at any time by pressing the speed
and incline buttons. However, when the next
ÒchirpÓ is heard, the speed and/or incline will
change to the next settings of the CD or video
program.
23. Always remove iFit.com CDÕs and videos from
your CD player or VCR when you are not
using them.
27. This treadmill is intended for in-home use
only. Do not use this treadmill in any commer-
cial, rental, or institutional setting.
WARNING:
Before beginning this or any exercise program, consult your physician. This
is especially important for persons over the age of 35 or persons with pre-existing health problems.
Read all instructions before using. ICON assumes no responsibility for personal injury or property
damage sustained by or through the use of this product.
SAVE THESE INSTRUCTIONS
The decals shown below have been placed on your treadmill. If the decal is missing, or if it is not legible,
please call our Customer Service Department, toll-free, to order a free replacement decal (see ORDERING
REPLACEMENT PARTS on the back cover of this manual). Apply the decal in the location shown.
Note: This decal is shown at 38% of actual size.
4
Download from Www.Somanuals.com. All Manuals Search And Download.
BEFORE YOU BEGIN
Thank you for selecting the revolutionary PROFORM¨
785Pi treadmill. The 785Pi treadmill combines ad-
vanced technology with innovative design to help you
get the most from your exercise program in the conve-
nience of your home. And when youÕre not exercising,
the unique 785Pi can be folded up, requiring less than
half the floor space of other treadmills.
at 1-800-999-3756, Monday through Friday, 6 a.m.
until 6 p.m. Mountain Time (excluding holidays). To
help us assist you, please note the product model
number and serial number before calling. The model
number of the treadmill is PFTL79192. The serial num-
ber can be found on a decal attached to the treadmill
(see the front cover of this manual for the location).
For your benefit, read this manual carefully before
using the treadmill. If you have additional questions,
please call our Customer Service Department toll-free
Before reading further, please familiarize yourself with
the parts that are labeled in the drawing below.
Book Holder
Hand Weight Holder*
Water Bottle
Holder (Bottle
not included)
Console
Pulse Sensor
Key/Clip
Handrail
Lock Knob
LEFT SIDE
RIGHT SIDE
Walking Belt
On/Off Switch
Circuit
Breaker
Foot Rail
Power Cord
Cushioned Walking Platform
Rear Roller
Adjustment Bolts
*For information about optional
hand weights, see page 18.
5
Download from Www.Somanuals.com. All Manuals Search And Download.
ASSEMBLY
Assembly requires two people. Set the treadmill in a cleared area and remove all packing materials. Do not
dispose of the packing materials until assembly is completed. Assembly requires the included allen wrench
and your own phillips screwdriver
and rubber mallet
.
Note: The underside of the treadmill walking belt is coated with high-performance lubricant. During shipping, a
small amount of lubricant may be transferred to the top of the walking belt or the shipping carton. This is a normal
condition and does not affect treadmill performance. If there is lubricant on top of the walking belt, simply wipe off
the lubricant with a soft cloth and a mild, non-abrasive cleaner.
1. With the help of a second person, carefully raise the
treadmill to the upright position.
1
While a second person tips the treadmill to one side
and holds it, insert one of the Extension Legs (102) into
the treadmill as shown. Make sure that the Extension
Leg is turned so the Base Pad (99) is on the bottom.
Next, tip the treadmill to the other side and insert the
other Extension Leg (not shown) in the same way. Lower
the side of the treadmill so that both Extension Legs
102
(102) are resting flat on the floor.
99
2. With the help of a second person, carefully lower the
treadmill frame and then tip the Uprights (69) down as
2
shown. Make sure that the Extension Legs (102) remain
in the Uprights.
99
Attach each Extension Leg (102) with two 3/4Ó Screws
(100) as shown.
Frame
With the help of a second person, carefully tip the
Uprights (69) back to the vertical position.
69
100
69
99
102
Note: One replacement Base Pad (99) may be included.
Use the extra Pad if one becomes worn or needs to be re-
placed.
100
102
3. Using the included allen wrench, tighten the Pulse Bar
Bolt (78) on each side of the treadmill.
3
76
Find the plastic tie inside the post on the right Upright (69).
Insert the plastic tie through a Handrail Extension (66) and
insert the Handrail Extension into the post as shown. Make
sure that the indicated holes are on top. Tap the Handrail
Extension with a rubber mallet to fully insert it. Attach the
Handrail Extension with two 1/2Ó Screws (67) as shown.
67
78
Holes
Cutout
75
69
Post
66
Tie
Identify the Right Foam Grip (75), which has a cutout in the
left side for the Pulse Bar (76). Slide the Right Foam Grip as
far as possible onto the post on the right Upright (69).
6
Download from Www.Somanuals.com. All Manuals Search And Download.
4. Make sure that the Right Foam Grip (75) is flush with the
Console Base (82) as shown. Tighten one of the two
1 1/4Ó Screws (33) into the side of the Right Foam Grip as
shown. Note: It may be necessary to pull the Foam Grip
out (see arrow A) to align the Screw with the hole in the
post.
4
82
A
33
Attach the Left Foam Grip (not shown) as described in
step 3 and this step. Note: There is no plastic tie in the left
side.
75
5. Press the Lock Knob Sleeve (70) into the left Upright (69).
5
Make sure that the Lock Pin Collar (72) and the Spring (71)
are on the Lock Pin. Insert the Lock Pin into the left Upright
(69) and tighten the Lock Knob (68) onto the Lock Pin.
69
70
68
71
72
74
6. Look at the Endcap (58). If the left or right foot on the End-
cap does not touch the floor, the included thick base pads
should be attached to the treadmill as described below.
6
Refer to assembly step 2. Lower the treadmill frame and
the Uprights (69) as shown. If the left foot of the Endcap
(58) was off the ground, remove the two Base Pads (99)
from the right Upright (69). Attach the included thick
base pads to the Upright. If the right side of the Endcap
was off the ground, attach the thick base pads to the left
Upright.
Foot
58
Foot
If either side of the Endcap (58) lifts off the floor when the
treadmill is used, attach the thick base pads as described.
7. Make sure that all parts are tightened before you use the treadmill. Keep the included allen wrench in a
secure place. The allen wrench is used to adjust the walking belt (see page 21). To protect the floor or carpet
from damage, place a mat under the treadmill.
7
Download from Www.Somanuals.com. All Manuals Search And Download.
OPERATION AND ADJUSTMENT
THE PERFORMANT LUBETM WALKING BELT
electric shock. This product is equipped with a cord
having an equipment-grounding conductor and a
grounding plug. Plug the power cord into a surge
protector, and plug the surge protector into an ap-
propriate outlet that is properly installed and
grounded in accordance with all local codes and
ordinances.
Your treadmill features a walking belt coated with
PERFORMANT LUBETM, a high-performance lubricant.
IMPORTANT: Never apply silicone spray or other
substances to the walking belt or the walking plat-
form. They will deteriorate the walking belt and
cause excessive wear.
This product is for use on a nominal 120-volt circuit,
and has a grounding plug that looks like the plug illus-
trated in drawing 1 below. A temporary adapter that
looks like the adapter illustrated in drawing 2 may be
used to connect the surge protector to a 2-pole recep-
tacle as shown in drawing 2 if a properly grounded out-
let is not available.
HOW TO PLUG IN THE POWER CORD
DANGER:
Improper connection
of the equipment-grounding conductor can
result in an increased risk of electric shock.
Check with a qualified electrician or service-
man if you are in doubt as to whether the
product is properly grounded. Do not modify
the plug provided with the productÑif it will
not fit the outlet, have a proper outlet in-
stalled by a qualified electrician.
The temporary adapter should be used only until a
properly grounded outlet (drawing 1) can be installed
by a qualified electrician.
The green-colored rigid ear, lug, or the like extending
from the adapter must be connected to a permanent
ground such as a properly grounded outlet box cover.
Whenever the adapter is used it must be held in place
by a metal screw. Some 2-pole receptacle outlet box
covers are not grounded. Contact a qualified elec-
trician to determine if the outlet box cover is
grounded before using an adapter.
Your treadmill, like any other type of sophisticated
electronic equipment, can be seriously damaged by
sudden voltage changes in your homeÕs power.
Voltage surges, spikes, and noise interference can re-
sult from weather conditions or from other appliances
being turned on or off.
To decrease the pos-
sibility of your tread-
1
Grounded Outlet Box
mill being damaged,
always use a surge
protector (not in-
cluded) with your
treadmill.
Treadmill Power Cord
Grounding Pin
Grounding Plug
Grounding Plug
Grounding Pin
Surge protectors are
sold at most hardware
stores and department
stores. Use only a UL-
listed surge protector,
rated at 15 amps, with a
14-gauge cord of five
feet or less in length.
Grounded Outlet
2
Grounded Outlet Box
Adapter
Grounding Pin
Grounding Plug
This product must be
grounded. If it should
malfunction or break
Surge Protector
down, grounding pro-
vides a path of least re-
sistance for electric cur-
rent to reduce the risk of
Lug
Metal Screw
8
Download from Www.Somanuals.com. All Manuals Search And Download.
CONSOLE DIAGRAM
Manual/Program Indicators
Display
Program Display
Display
Program Indicators
Note: If there is a thin sheet
of clear plastic on the face
of the console, remove it.
Key
Clip
Pulse Display
Thumb Pulse Sensor
The console also features new iFit.com interactive tech-
nology. IFit.com technology is like having a personal
trainer right in your home. Using the included audio
cable, you can connect the treadmill to your home
stereo, portable stereo, or computer and play special
iFit.com CD programs (CDÕs are available separately).
IFit.com CD programs automatically control the speed
and incline of the treadmill as a personal trainer guides
you through every step of your workout. High-energy
music provides added motivation. Each CD features
two programs designed by certified personal trainers.
CAUTION:Before operating the
console, read the following precautions.
¥ Do not stand on the walking belt when turn-
ing on the power.
¥ Always wear the clip (see the drawing
above) while operating the treadmill.
¥ Adjust the speed in small increments to
avoid sudden jumps in speed.
In addition, you can connect the treadmill to your VCR
and TV and play iFit.com video programs (videocas-
settes are available separately). Video programs offer
the same benefits as iFit.com CD programs, but add
the excitement of working out with a class and an
instructorÑthe hottest new trend at health clubs.
¥ To reduce the possibility of electric shock,
keep the console dry. Avoid spilling liquids
on the console and place only a sealed water
bottle in the water bottle holder.
FEATURES OF THE CONSOLE
With the treadmill connected to your computer, you
and access basic programs, audio programs, and
video programs directly from the internet. And by
adding an optional upgrade module to the treadmill,
you can use virtually endless features from our internet
The advanced console offers an impressive array of
features to help you get the most from your exercise.
When the console is in the manual mode, the speed
and incline of the treadmill can be changed with a touch
of a button. As you exercise, the console will display
continuous exercise feedback. You can even measure
your heart rate using the built-in thumb pulse sensor.
Note: See page 18 for information about an optional
chest pulse sensor.
To purchase iFit.com CDÕs or videocassettes or an
optional upgrade module, call toll-free 1-800-735-0768.
To use the manual mode of the console, follow the
steps beginning on page 10. To use a personal trainer
program, see page 11. To use an iFit.com CD or
video program, refer to page 15. To use an iFit.com
program directly from our internet site, see page 17.
Eight certified personal trainer programs are also
offered. Each program automatically controls the
speed and incline of the treadmill to give you an effec-
tive low-, medium-, or high-intensity workout.
9
Download from Www.Somanuals.com. All Manuals Search And Download.
HOW TO TURN ON THE POWER
To stop the walking belt, press the Stop button.
The Time/Segment Time display will begin to
flash. To restart the walking belt, press the Start
Plug in the power cord (see HOW TO PLUG IN
THE POWER CORD on page 8).
1
button or the Speed
▲
button.
Change the incline of the treadmill as desired.
Locate the on/off
4
5
2
switch on the treadmill
On
near the power cord.
Position
To change the incline of
the treadmill, press the
Incline buttons. Each time
one of the buttons is
pressed, the incline will
change by 0.5%. The
incline range is 1.5% to 10%. Note: After the
buttons are pressed, it may take a moment for the
treadmill to reach the selected incline setting.
Move the on/off switch
to the on position.
Stand on the foot rails
of the treadmill. Find
the clip attached to the
key and slide the clip
onto the waistband of
your clothing. Next, in-
sert the key into the console. After a moment, the
displays and various indicators will light. Test the
clip by carefully taking a few steps backward
until the key is pulled from the console. If the
key is not pulled from the console, adjust the
position of the clip as needed.
3
Follow your progress with the LED track and
the displays.
The LED TrackÑWhen
the manual mode or an
iFit.com program is se-
lected, the program dis-
play will show an LED
track representing 1/4
mile. As you exercise,
HOW TO USE THE MANUAL MODE
the indicators around the track will light in sequence
until you have completed 1/4 mile. A new lap will
then begin.
Insert the key fully into the console.
1
See HOW TO TURN ON THE POWER above.
Distance/Laps/
Incline displayÑThis
display shows the dis-
tance that you have
walked and the number of
1/4-mile laps you have
Select the manual mode.
2
When the key is in-
serted, the manual
mode will be selected
and the Manual Control
indicator will light. If a
program has been se-
lected, press the Program button repeatedly to se-
lect the manual mode.
completed. The display will alternate between one
number and the other every seven seconds. The
LAPS indicator will light when the number of laps
is shown. In addition, each time the Incline buttons
are pressed, the display will show the current in-
cline setting for several seconds.
Press the Start button or the Speed
start the walking belt.
▲
button to
3
Time/Segment Time dis-
playÑWhen the manual
A moment after the button is pressed, the walking
belt will begin to move at 1 mph. Hold the handrails
and begin walking. As you exercise, change the
speed of the walking
mode or an iFit.com pro-
gram is selected, this dis-
play will show the elapsed
time. When a personal
belt as desired by
pressing the Speed
buttons. Each time a
button is pressed, the
speed setting will
change by 0.1 mph; if a
trainer program is selected, the display will show
both the time remaining in the program and the
time remaining in the current segment of the pro-
gram. The display will alternate between one num-
ber and the other every seven seconds. The SEG
indicator will light when the segment time is shown.
button is held down, the speed setting will change
in increments of 0.5 mph. The speed range is 0.5
mph to 10 mph.
10
Download from Www.Somanuals.com. All Manuals Search And Download.
Calories/Fat Calories
displayÑThis
display shows the
approximate numbers of
calories and fat calories
you have burned (see
FAT BURNING on page 22). Every seven sec-
onds, the display will change from one number to
the other. The FAT indicator will light when the
number of fat calories is shown.
rate will be shown. Hold your thumbs on the sen-
sor for another 15 seconds for the most accurate
reading. If the displayed heart rate appears to be
too high or too low, or if your heart rate is not dis-
played, lift your thumbs off the sensors and allow
the display to reset. Then, place your thumbs on
the sensors as described above.
Try the pulse sensor several times until you be-
come familiar with it. Remember to stand still
while measuring your heart rate. Note: If the op-
tional chest pulse sensor is worn, your heart rate
will be displayed in the Pulse display.
Speed/Min-Mile
displayÑThis display
shows the speed of the
walking belt and your
current pace (pace is
measured in minutes per
mile). Every seven seconds, the display will
change from one number to the other. The M/M
indicator will light when your pace is shown.
When you are finished, remove the key.
7
Step onto the foot rails, press the Stop button, and
remove the key from the console. Keep the key in
a secure place. Note: If the displays and various
indicators on the console remain lit after the
key is removed, the console is in the ÒdemoÓ
mode. See page 18 and turn off the demo mode.
Note: The console can
display speed and dis-
tance in either miles or
kilometers. To find which
unit of measurement is
selected, hold down the
When you are finished using the treadmill, move
the on/off switch near the power cord to the off
position and unplug the power cord.
Stop button while inserting the key into the con-
sole. An ÒE,Ó for English miles, or an ÒM,Ó for metric
kilometers, will appear in the display. Press the
HOW TO USE PERSONAL TRAINER PROGRAMS
Speed
▲
button to change the unit of measure-
Insert the key fully into the console.
ment. When the desired unit of measurement is
selected, remove the key and then reinsert it.
Note: For simplicity, all instructions in this manual
refer to miles.
1
See HOW TO TURN ON THE POWER on page
10.
Select one of the personal trainer programs.
To reset the displays, press the Stop button, re-
move the key, and then reinsert the key.
2
When the key is
inserted, the
manual mode
will be selected
and the Manual
Control indicator
will light. To se-
lect one of the personal trainer programs, press
the Program button repeatedly until one of the
eight personal trainer program indicators lights.
Measure your heart rate, if desired.
6
Note: Before using the pulse sensor, make sure
that your hands are clean.
To measure your
heart rate, stand
on the foot rails
and place both
thumbs on the
pulse sensors as
shown. Do not
press too hard,
or the circulation
in your thumbs
will be restricted
and your heart
The console features three low-intensity programs,
two medium-intensity programs, and three high-
intensity programs. The profiles on the console
show how the speed and incline of the treadmill
will change during the programs. The numbers
beside the profiles show the maximum speed and
incline settings for the programs. For example, the
upper left profile shows that the treadmill will reach
a maximum speed of 4.5 mph and a maximum
incline of 5% during the first program.
rate will not be
detected. After a few seconds, one or two dashes
will appear in the Pulse display and then your heart
11
Download from Www.Somanuals.com. All Manuals Search And Download.
The program display
will show a simplified
profile of the program
you have selected. The
Time/Segment Time
display will show how
long the program will
last.
the highest indicators in the columns will appear in
the program display. When the speed settings
move to the left again and not all of the indicators
in the Current Segment column are lit, the speed
settings will move back up.
If the speed or incline setting for the current
segment is too high or too low, you can manually
override the setting by pressing the Speed or
Incline buttons on the console. Every few times
one of the Speed buttons is pressed, an additional
indicator will light or darken in the Current Segment
column. If any of the columns to the right of the
Current Segment column have the same number
of lit indicators as the Current Segment column,
an additional indicator may light or darken in those
columns as well. Note: If you manually adjust the
speed setting so that all of the indicators in the
Current Segment column are lit, the speed settings
in the program display will not move downward as
described above. When the current segment of
the program ends, the treadmill will automati-
cally adjust to the speed and incline settings
for the next segment.
Press the Start button or the Speed
start the program.
▲
button to
3
A moment after the button is pressed, the tread-
mill will automatically adjust to the first speed and
incline settings for the program. Hold the handrails
and begin walking.
Each program is divided into several time seg-
ments of different lengths. The Time/Segment
Time display shows both the time remaining in the
program and the time
remaining in the current
segment. One speed
Current Segment
setting and one incline
setting are programmed
To stop the program temporarily, press the Stop
button. The Time/Segment Time display will begin
to flash. To restart the program, press the Start but-
for each segment. The
speed setting for the
first segment will be
shown in the flashing
ton or the Speed
▲
button. To end the program,
press the Stop button, remove the key, and then
reinsert the key.
Current Segment column of the program display.
(The incline settings are not shown in the program
display.) The speed settings for the next seven
segments will be shown in the seven columns to
the right.
Follow your progress with the displays.
Refer to step 5 on page 10.
4
5
6
When only three seconds remain in the first seg-
ment of the program, both the Current Segment
column and the column to the right will flash, a se-
ries of tones will sound, and all speed settings will
move one column to the left. The speed setting for
the second segment will then be shown in the
flashing Current Segment column and the tread-
mill will automatically adjust to the speed and in-
cline settings for the second segment.
Measure your heart rate, if desired.
See step 6 on page 11.
When the program is completed, remove the
key from the console.
When the program is completed, remove the key
from the console. Keep the key in a secure place.
Note: If the displays and various indicators on
the console remain lit after the key is removed,
the console is in the ÒdemoÓ mode. Refer to
page 18 and turn off the demo mode.
The program will continue in this way until the
speed setting for the last segment is shown in the
Current Segment column and no time remains in
the Time/Segment Time display. The walking belt
will then slow to a stop.
When you are finished using the treadmill, move
the on/off switch near the power cord to the off
position and unplug the power cord.
Note: Each time a segment ends and the speed
settings move one column to the left, if all of the
indicators in the Current Segment column are lit,
the speed settings will move downward so that only
12
Download from Www.Somanuals.com. All Manuals Search And Download.
HOW TO CONNECT YOUR PORTABLE STEREO
HOW TO CONNECT THE TREADMILL TO YOUR
CD PLAYER, VCR, OR COMPUTER
Note: If your stereo has an RCA-type AUDIO OUT
jack, see instruction A below. If your stereo has a
3.5mm LINE OUT jack, see instruction B. If your
stereo has only a PHONES jack, see instruction C.
To use iFit.com CDÕs, the treadmill must be con-
nected to your portable CD player, portable stereo,
home stereo, or computer with CD player. See pages
13 and 14 for connecting instructions. To use iFit.com
videocassettes, the treadmill must be connected to
your VCR. See page 15 for connecting instructions. To
use iFit.com programs directly from our internet
site, the treadmill must be connected to your home
computer. See page 14 for connecting instructions.
A. Plug one end of the audio cable into the jack on the
front of the treadmill near the power cord. Plug the
other end of the cable into the included adapter. Plug
the adapter into an AUDIO OUT jack on your stereo.
A
HOW TO CONNECT YOUR PORTABLE CD PLAYER
AUDIO OUT
RIGHT
LEFT
Note: If your CD player has separate LINE OUT and
PHONES jacks, see instruction A below. If your CD
player has only one jack, see instruction B.
Audio
Cable
Adapter
A. Plug one end of the audio cable into the jack on the
front of the treadmill near the power cord. Plug the
other end of the cable into the LINE OUT jack on
your CD player. Plug your headphones into the
PHONES jack.
B. Plug one end of the audio cable into the jack on the
front of the treadmill near the power cord. Plug the
other end of the cable into the LINE OUT jack on
your stereo.
A
PHONES LINE OUT
LINE OUT
PHONES
B
Head-
phones
Audio
Cable
LINE OUT
Audio
Cable
B. Plug one end of the audio cable into the jack on the
front of the treadmill near the power cord. Plug the
other end of the cable into a 3.5mm Y-adapter
(available at electronics stores). Plug the Y-adapter
into the PHONES jack on your CD player. Plug your
headphones into the other side of the Y-adapter.
C. Plug one end of the audio cable into the jack on the
front of the treadmill near the power cord. Plug the
other end of the cable into a 3.5mm Y-adapter
(available at electronics stores). Plug the Y-adapter
into the PHONES jack on your stereo. Plug your
headphones into the other side of the Y-adapter.
B
PHONES
C
PHONES
3.5mm
Y-adapter
Audio
Cable
PHONES
3.5mm
Y-adapter
Audio
Cable
Headphones
Headphones
13
Download from Www.Somanuals.com. All Manuals Search And Download.
HOW TO CONNECT YOUR HOME STEREO
HOW TO CONNECT YOUR COMPUTER
Note: If your stereo has an unused LINE OUT jack,
see instruction A below. If the LINE OUT jack is
being used, see instruction B.
Note: If your computer has a 3.5mm LINE OUT jack,
see instruction A. If your computer has only a
PHONES jack, see instruction B.
A. Plug one end of the audio cable into the jack on the
front of the treadmill near the power cord. Plug the
other end of the cable into the included adapter.
Plug the adapter into the LINE OUT jack on your
stereo.
A. Plug one end of the audio cable into the jack on the
front of the treadmill near the power cord. Plug the
other end of the cable into the LINE OUT jack on
your computer.
A
A
CD
LINE OUT
VCR
Amp
LINE OUT
Audio
Cable
LINE OUT
Audio
Cable
Adapter
B. Plug one end of the audio cable into the jack on the
front of the treadmill near the power cord. Plug the
other end of the cable into a 3.5mm Y-adapter
(available at electronics stores). Plug the Y-adapter
into the PHONES jack on your computer. Plug your
headphones or speakers into the other side of the
Y-adapter.
B. Plug one end of the audio cable into the jack on the
front of the treadmill near the power cord. Plug the
other end of the cable into the included adapter.
Plug the adapter into an RCA adapter (available at
electronics stores). Next, remove the wire that is
currently plugged into the LINE OUT jack on your
stereo and plug the wire into the unused side of the
RCA adapter. Plug the RCA adapter into the LINE
OUT jack on your stereo.
B
PHONES
B
CD
Audio
Cable
3.5mm
Y-adapter
VCR
Amp
LINE OUT
Headphones/Speakers
RCA
Adapter
Audio
Cable
Adapter
Wire removed from
LINE OUT jack
14
Download from Www.Somanuals.com. All Manuals Search And Download.
HOW TO CONNECT YOUR VCR
HOW TO USE IFIT.COM CD AND VIDEO
PROGRAMS
Note: If your VCR has an unused AUDIO OUT jack,
see instruction A below. If the AUDIO OUT jack is
being used, see instruction B. If you have a TV
with a built-in VCR, see instruction B. If your VCR
is connected to your home stereo, see HOW TO
CONNECT YOUR HOME STEREO on page 14.
To use iFit.com CDÕs or videocassettes, the treadmill
must be connected to your portable CD player, portable
stereo, home stereo, computer with CD player, or
VCR. See HOW TO CONNECT THE TREADMILL TO
YOUR CD PLAYER, VCR, OR COMPUTER on page
13. Note: To purchase iFit.com CDÕs or videocas-
settes, call toll-free 1-800-735-0768.
A. Plug one end of the audio cable into the jack on the
front of the treadmill near the power cord. Plug the
other end of the cable into the included adapter.
Plug the adapter into the AUDIO OUT jack on your
VCR.
Follow the steps below to use an iFit.com CD or video
program.
A
Insert the key into the console.
ANT IN
.
VIDEO AUDIO
IN
RF OUT
1
CH
3
4
OUT
See HOW TO TURN ON THE POWER on page 10.
AUDIO OUT
RIGHT
LEFT
Select the iFit.com mode.
2
Audio
Cable
Adapter
When the key is in-
serted, the manual
mode will be selected
and the Manual Control
indicator will light. To
use iFit.com CDÕs or
videocassettes, press the Program button repeat-
edly until the iFit.com indicator lights.
B. Plug one end of the audio cable into the jack on the
front of the treadmill near the power cord. Plug the
other end of the cable into the included adapter.
Plug the adapter into an RCA adapter (available at
electronics stores). Next, remove the wire that is
currently plugged into the AUDIO OUT jack on your
VCR and plug the wire into the unused side of the
RCA adapter. Plug the RCA adapter into the AUDIO
OUT jack on your VCR.
Insert the iFit.com CD or videocassette.
3
If you are using an iFit.com CD, insert the CD into
your CD player. If you are using an iFit.com video-
cassette, insert the videocassette into your VCR.
Press the PLAY button on your CD player or
VCR.
4
B
ANT. IN
VIDEO AUDIO
IN
RF OUT
CH
3
4
OUT
A moment after the button is pressed, your per-
sonal trainer will begin guiding you through your
workout. Simply follow your personal trainerÕs
instructions. Note: If the Time/Segment Time dis-
play is flashing, press the Start button or the
RCA Adapter
Adapter
Audio
Cable
Speed
▲
button on the console. The treadmill will
not respond to a CD or video program when the
Time/Segment Time display is flashing.
Wire removed from
AUDIO OUT jack
During the CD or video program, an electronic
ÒchirpingÓ sound will alert you when the speed
and/or incline of the treadmill is about to change.
CAUTION: Always listen for the ÒchirpÓ and be
prepared for speed and/or incline changes. In
some instances, the speed and/or incline may
change before the personal trainer describes
the change.
15
Download from Www.Somanuals.com. All Manuals Search And Download.
If the speed or incline settings are too high or too
low, you can manually override the settings at any
time by pressing the Speed or Incline buttons on
the console. However, when the next ÒchirpÓ is
heard, the speed and/or incline will change to
the next settings of the CD or video program.
another flat surface instead of on the console.
Follow your progress with the LED track and
the displays.
5
See step 5 on page 10.
Measure your heart rate, if desired.
Refer to step 6 on page 11.
To stop the walking belt at any time, press the
Stop button on the console. The Time/Segment
Time display will begin to flash. To restart the pro-
6
7
gram, press the Start button or the Speed
▲
but-
When the program is completed, remove the
key.
ton. After a moment, the walking belt will begin to
move at 1.0 mph. When the next ÒchirpÓ is
heard, the speed and incline will change to the
next settings of the CD or video program. The
program can also be stopped by pressing the
Stop button on your CD player or VCR.
When the program is completed, remove the key
from the console. Keep the key in a secure place.
Note: If the displays and various indicators on
the console remain lit after the key is removed,
the console is in the ÒdemoÓ mode. Refer to
page 18 and turn off the demo mode.
When the CD or video program is completed, the
walking belt will stop and the Time/Segment Time
display will begin to flash. Note: To use another
CD or video program, press the Stop button or re-
move the key and go to step 1 on page 15.
When you are finished using the treadmill, move
the on/off switch near the power cord to the off
position and unplug the power cord.
Note: If the speed or incline of the treadmill
does not change when a ÒchirpÓ is heard:
¥ make sure that the iFit.com indicator is lit and
that the Time/Segment Time display is not
flashing. If the Time/Segment Time display is
flashing, press the Start button or the Speed
▲
button on the console
¥ adjust the volume of your CD player or VCR. If
the volume is too high or too low, the console
may not detect the program signals
¥ make sure that the audio cable is properly
connected, that it is fully plugged in, and that
it is not wrapped around a power cord
¥ if you are using your portable CD player and
the CD skips, set the CD player on the floor or
16
Download from Www.Somanuals.com. All Manuals Search And Download.
Return to the treadmill and stand on the foot
rails. Find the clip attached to the key and slide
the key onto the waistband of your clothing.
HOW TO USE PROGRAMS DIRECTLY FROM
OUR INTERNET SITE
7
When the on-screen countdown ends, the program
will begin and the walking belt will begin to move.
Hold the handrails, step onto the walking belt, and
begin walking. During the program, an electronic
ÒchirpingÓ sound will alert you when the speed
and/or incline of the treadmill is about to change.
CAUTION: Always listen for the ÒchirpÓ and be
prepared for speed and/or incline changes.
access a selection of programs that interactively con-
trol your treadmill to help you achieve your specific ex-
ercise goals. In addition, you can play iFit.com audio
and video programs directly from the internet. By
adding an optional upgrade module to the console, you
can use virtually endless features on our internet site.
grade module, call toll-free 1-800-735-0768.
If the speed or incline settings are too high or too
low, you can manually override the settings at any
time by pressing the Speed or Incline buttons on
the console. However, when the next ÒchirpÓ is
heard, the speed and/or incline will change to
the next settings of the program.
To use programs from our internet site, the treadmill
must be connected to your home computer. See HOW
TO CONNECT YOUR COMPUTER on page 14. In
addition, you must have an internet connection and
an internet service provider. A list of specific system
requirements will be found on our internet site.
To stop the walking belt at any time, press the
Stop button on the console. The Time/Segment
Time display will begin to flash. To restart the pro-
Follow the steps below to use a program from our
internet site.
gram, press the Start button or the Speed
▲
but-
ton. After a moment, the walking belt will begin to
move at 1.0 mph. When the next ÒchirpÓ is
heard, the speed and incline will change to the
next settings of the program.
Insert the key into the console.
1
See HOW TO TURN ON THE POWER on page 10.
Select the iFit.com mode.
When the program is completed, the walking belt
will stop and the Time/Segment Time display will
begin to flash. Note: To use another program,
press the Stop button and go to step 5.
2
When the key is in-
serted, the manual
mode will be selected
and the Manual Control
indicator will light. To
use a program from our
internet site, press the Program button repeatedly
until the iFit.com indicator lights.
Note: If the speed or incline of the treadmill
does not change when a ÒchirpÓ is heard, make
sure that the iFit.com indicator is lit and that
the Time/Segment Time display is not flashing.
In addition, make sure that the audio cable is
properly connected, that it is fully plugged in,
and that it is not wrapped around a power cord.
Go to your computer and start an internet
connection.
3
Follow your progress with the LED track and
the displays.
Start your web browser, if necessary, and go to
8
9
4
See step 5 on page 10.
Follow the desired links on our internet site to
select a program.
5
When the program has ended, remove the key.
Read and follow the on-line instructions for using a
program.
When the program has ended, remove the key
from the console. Keep the key in a secure place.
Note: If the displays and indicators on the con-
sole remain lit after the key is removed, the
console is in the ÒdemoÓ mode. Refer to page
18 and turn off the demo mode.
Follow the on-line instructions to start the
program.
6
When you start the program, an on-screen count-
down will begin.
When you are finished using the treadmill, move
the on/off switch near the power cord to the off
position and unplug the power cord.
17
Download from Www.Somanuals.com. All Manuals Search And Download.
THE INFORMATION MODE/DEMO MODE
THE OPTIONAL CHEST PULSE SENSOR
The console features an information mode that keeps
track of the total number of hours that the treadmill has
been operated and the total number of miles that the
walking belt has moved. The information mode also
allows you to switch the console from miles per hour to
kilometers per hour. In addition, the information mode
allows you to turn on and turn off the demo mode.
An optional chest pulse sensor adds even more
features to the console. The chest pulse sensor offers
hands-free operation and continuously monitors your
heart rate during your workouts. To purchase the
optional chest pulse sensor, call the toll-free tele-
phone number listed on the back cover of this
manual.
To select the information mode, hold down the Stop
button while inserting the key into the console. When
the information mode is selected, the following informa-
tion will be shown:
The Distance/Laps/Incline
display will show the total
number of miles that the walk-
ing belt has moved.
The Time/Segment Time dis-
play will show the total num-
ber of hours the treadmill has
been used.
OPTIONAL HAND WEIGHTS
Optional hand weights
let you exercise your
upper-body while you
walk on the treadmill.
The hand weights fit
into convenient holders
in the console. Hand
An ÒE,Ó for english miles, or
an ÒM,Ó for metric kilometers,
will appear in the Speed/ Min-
Mile display. Press the Speed
weights are available in
2-pound and 3-pound
sizes. To purchase
▲ button to change the unit of
measurement.
hand weights, call the
toll-free telephone number listed on the back cover
of this manual.
IMPORTANT: The
Calories/Fat Calories dis-
play should be blank. If a ÒdÓ
appears in the display, the
console is in the ÒdemoÓ
mode. This mode is intended
to be used only when a treadmill is displayed in a store.
When the console is in the demo mode, the power cord
can be plugged in, the key can be removed from the
console, and the displays and indicators on the console
will automatically light in a preset sequence, although
the buttons on the console will not operate. If a ÒdÓ ap-
pears in the Calories/Fat Calories display when the
information mode is selected, press the Speed
button so the Calories/ Fat Calories display is
blank.
▼
To exit the information mode, remove the key from the
console.
18
Download from Www.Somanuals.com. All Manuals Search And Download.
HOW TO FOLD AND MOVE THE TREADMILL
HOW TO FOLD THE TREADMILL FOR STORAGE
1
Before folding the treadmill, adjust the incline to the
lowest position. If this is not done, the treadmill may be
permanently damaged. Next, unplug the power cord.
CAUTION: You must be able to safely lift 45 pounds (20
kg) in order to raise, lower, or move the treadmill.
1. Hold the treadmill with your hands in the locations shown
at the right. CAUTION: To decrease the possibility of in-
jury, bend your legs and keep your back straight. As
you raise the treadmill, make sure to lift with your legs
rather than your back. Raise the treadmill about halfway
to the vertical position.
2. Move your right hand to the position shown and hold the
treadmill firmly. Using your left hand, pull the latch knob to
2
the left and hold it. Raise the treadmill until the latch pin is
aligned with the hole in the catch. Insert the latch pin into
the catch. Make sure that the latch pin is fully inserted
into the catch.
To protect the floor or carpet from damage, place a
Knob
Catch
mat under the treadmill. Keep the treadmill out of
direct sunlight. Do not leave the treadmill in the stor-
age position in temperatures above 85¡ Fahrenheit.
HOW TO MOVE THE TREADMILL
Before moving the treadmill, convert the treadmill to the stor-
age position as described above. Make sure that the pin
on the lock knob is inserted into the slot in the catch.
Pulse Bar
1. Hold the handrails as shown and place one foot against a
wheel. It may be helpful to grab the pulse bar as you tip
the treadmill.
2. Tilt the treadmill back until it rolls freely on the front wheels.
Carefully move the treadmill to the desired location. Never
move the treadmill without tipping it back. To reduce
the risk of injury, use extreme caution while moving
the treadmill. Do not attempt to move the treadmill
over an uneven surface.
Base
Front Wheels
3. Place one foot on the base, and carefully lower the tread-
mill until it is resting in the storage position.
HOW TO LOWER THE TREADMILL FOR USE
1. Refer to drawing 2 above. Hold the upper end of the treadmill with your right hand as shown. Using your left
hand, pull the lock knob to the left and hold it. Pivot the treadmill down until the frame is past the pin on the lock
knob. Note: You may need to push the handrail to the side slightly.
2. Refer to drawing 1 above. Hold the treadmill firmly with both hands, and lower the treadmill to the floor.
CAUTION: To decrease the possibility of injury, bend your legs and keep your back straight.
19
Download from Www.Somanuals.com. All Manuals Search And Download.
TROUBLE-SHOOTING
Most treadmill problems can be solved by following the steps below. Find the symptom that applies, and
follow the steps listed. If further assistance is needed, please call our Customer Service Department toll-
free at 1-800-999-3756, Monday through Friday, 6 a.m. until 6 p.m. Mountain Time (excluding holidays).
PROBLEM: The power does not turn on
SOLUTION: a. Make sure that the power cord is plugged into a surge protector, and that the surge protector is
plugged into a properly grounded outlet. (See HOW TO PLUG IN THE POWER CORD on page
8.) Use only a UL-listed surge protector, rated at 15 amps, with a 14-gauge cord of five feet or
less in length.
b. After the power cord has been plugged in, make sure that the key is fully inserted into the console.
c. Check the circuit breaker located on the treadmill
near the power cord. If the switch protrudes as
c
shown, the circuit breaker has tripped. To reset the
circuit breaker, wait for five minutes and then press
the switch back in.
Tripped
Reset
d
d. Check the on/off switch located on the treadmill
near the power cord. The switch must be in the on
position.
On
Position
PROBLEM: The power turns off during use
SOLUTION: a. Check the circuit breaker located on the treadmill frame near the power cord (see c. above). If the
circuit breaker has tripped, wait for five minutes and then press the switch back in.
b. Make sure that the power cord is plugged in.
c. Remove the key from the console. Reinsert the key fully into the console.
d. Make sure that the on/off switch is in the on position.
e. If the treadmill still will not run, please call our Customer Service Department, toll-free.
PROBLEM: The displays of the console do not function properly
SOLUTION: a. Remove the key from the console and unplug the
power cord. Carefully tip the treadmill down as shown
a
in drawing a. Remove the Screws (39, 83) from the
hood. Raise the Uprights (69) and carefully remove
the hood.
39
83
69
b. Locate the Reed Switch (10) and the Magnet (7) on
the left side of the Pulley (8). Turn the Pulley until the
Magnet is aligned with the Reed Switch. Make sure
that the gap between the Magnet and the Reed
Switch is about 1/8Ó. If necessary, loosen the 1/2Ó
Screw (67) and move the Reed Switch slightly.
Retighten the Screw. Re-attach the hood, and run the
treadmill for a few minutes to check for a correct
speed reading.
b
1/8Ó
8
67
10
7
Top
View
20
Download from Www.Somanuals.com. All Manuals Search And Download.
PROBLEM: The thumb pulse sensor does not function properly
SOLUTION: a. Wash your hands before to using the pulse sensor. In addition, keep the pulse sensor clean using
a damp cloth and a small amount of mild detergent.
PROBLEM: The walking belt slows when walked on
SOLUTION: a. Use only a UL-listed surge protector, rated at 15 amps, with a 14-gauge cord of five feet or less in
length.
b. If the walking belt is overtightened, treadmill perfor-
mance may decrease and the walking belt may be-
b
3ÓÐ4Ó
come damaged. Remove the key and UNPLUG THE
POWER CORD. Using the allen wrench, turn both
rear roller adjustment bolts counterclockwise, 1/4 of a
turn. When the walking belt is properly tightened, you
should be able to lift each side of the walking belt 3 to
4 inches off the walking platform. Be careful to keep
the walking belt centered. Plug in the power cord, in-
sert the key and run the treadmill for a few minutes.
Repeat until the walking belt is properly tightened.
Rear Roller Adjustment Bolts
c. If the walking belt still slows, please call our Customer Service Department, toll-free.
PROBLEM: The walking belt is off-center
SOLUTION: a. If the walking belt has shifted to the left, first remove
the key and UNPLUG THE POWER CORD. Using the
allen wrench, turn the left rear roller adjustment bolt clock-
wise, and the right bolt counterclockwise, 1/4 of a turn each.
Be careful not to overtighten the walking belt. Plug in the
power cord, insert the key and run the treadmill for a few
minutes. Repeat until the walking belt is centered.
a
b. If the walking belt has shifted to the right, first remove
the key and UNPLUG THE POWER CORD. Using the
allen wrench, turn the left rear roller adjustment bolt coun-
terclockwise, and the right bolt clockwise, 1/4 of a turn
each. Be careful not to overtighten the walking belt. Plug
in the power cord, insert the key and run the treadmill for
a few minutes. Repeat until the walking belt is centered.
b
PROBLEM: The walking belt slips when walked on
SOLUTION: a. If the walking belt slips when walked on, first remove the
key and UNPLUG THE POWER CORD. Using the allen
wrench, turn both rear roller adjustment bolts clockwise,
1/4 of a turn. When the walking belt is correctly tightened,
you should be able to lift each side of the walking belt 3 to
4 inches off the walking platform. Be careful to keep the
walking belt centered. Plug in the power cord, insert the
key and carefully walk on the treadmill for a few minutes.
Repeat until the walking belt is properly tightened.
a
PROBLEM: The incline of the treadmill does not change correctly or does not change when iFit.com
CDÕs and videos are played
SOLUTION: a. With the key in the console, press one of the INCLINE buttons. While the incline is changing,
remove the key. After a few seconds, re-insert the key. The treadmill will automatically rise to the
maximum incline level and then return to the minimum level. This will recalibrate the incline.
21
Download from Www.Somanuals.com. All Manuals Search And Download.
CONDITIONING GUIDELINES
uses easily accessible carbohydrate calories for en-
ergy. Only after the first few minutes does your body
begin to use stored fat calories for energy. If your goal
is to burn fat, adjust the speed and incline of the tread-
mill until your heart rate is near the lowest number in
your training zone.
WARNING:
Before beginning this
or any exercise program, consult your physi-
cian. This is especially important for individu-
als over the age of 35 or individuals with pre-
existing health problems.
For maximum fat burning, adjust the speed and incline
of the treadmill until your heart rate is near the middle
number in your training zone.
The pulse sensor is not a medical device.
Various factors, including your movement,
may affect the accuracy of heart rate readings.
The sensor is intended only as an exercise aid
in determining heart rate trends in general.
Aerobic Exercise
If your goal is to strengthen your cardiovascular sys-
tem, your exercise must be Òaerobic.Ó Aerobic exercise
is activity that requires large amounts of oxygen for
prolonged periods of time. This increases the demand
on the heart to pump blood to the muscles, and on the
lungs to oxygenate the blood. For aerobic exercise,
adjust the speed and incline of the treadmill until your
heart rate is near the highest number in your training
zone.
The following guidelines will help you to plan your ex-
ercise program. RememberÑthese are general guide-
lines only. For more detailed exercise information, ob-
tain a reputable book or consult your physician.
EXERCISE INTENSITY
Whether your goal is to burn fat or to strengthen your
cardiovascular system, the key to achieving the
WORKOUT GUIDELINES
desired results is to exercise with the proper intensity.
The proper intensity level can be found by using your
heart rate as a guide. The chart below shows recom-
mended heart rates for fat burning and aerobic exercise.
Each workout should include the following three parts:
A Warm-upÑStart each workout with 5 to 10 minutes
of stretching and light exercise. A proper warm-up in-
creases your body temperature, heart rate and circula-
tion in preparation for exercise.
Training Zone ExerciseÑAfter warming up, increase
the intensity of your exercise until your pulse is in your
training zone for 20 to 60 minutes. (During the first few
weeks of your exercise program, do not keep your
pulse in your training zone for longer than 20 minutes.)
Breathe regularly and deeply as you exerciseÑnever
hold your breath.
To find the proper heart rate for you, first find your age
near the bottom of the chart (ages are rounded off to
the nearest ten years). Next, find the three numbers
above your age. The three numbers define your Òtrain-
ing zone.Ó The lower two numbers are recommended
heart rates for fat burning; the higher number is the
recommended heart rate for aerobic exercise.
A Cool-downÑFinish each workout with 5 to 10 min-
utes of stretching to cool down. This will increase the
flexibility of your muscles and will help prevent post-ex-
ercise problems.
To measure your heart rate during exercise, use the
pulse sensor on the console. If your heart rate is too
high or too low, adjust the speed and incline of the
treadmill.
Exercise Frequency
To maintain or improve your condition, complete three
workouts each week, with at least one day of rest be-
tween workouts. After a few months, you may com-
plete up to five workouts each week if desired.
Fat Burning
To burn fat effectively, you must exercise at a relatively
low intensity level for a sustained period of time.
During the first few minutes of exercise, your body
The key to success is to make exercise a regular and
enjoyable part of your everyday life.
22
Download from Www.Somanuals.com. All Manuals Search And Download.
PART LISTÑModel No. PFTL79192
R0100A
To locate the parts listed below, refer to the EXPLODED DRAWING attached in the center of this manual.
Key
No. Qty. Description
Key
No. Qty. Description
Key
No. Qty. Description
1
2
3
4
5
6
7
8
9
10
2
2
2
1
2
2
1
1
8
1
Foot Rail Insert
Foot Rail
46
47
48
49
50
51
52
53
54
55
56
1
4
8
16
1
1
1
4
4
2
Belt Guide
Isolator
Isolator Screw
Fastener
Belly Pan
91
92
93
94
95
96
97
98
1
1
2
2
2
1
1
1
4
6
1
2
2
2
1
2
Cable Tie Clamp
8Ó Cable Tie
Lift Pivot Bolt
Wheel Bolt
Wheel
Right Endcap Insert
Grommet
Upright Wire Harness
Base Pad
3/4Ó Screw
Motor Washer
Extension Leg
Extension Cap
Incline Warning Decal
Shock
Extension Leg
Assembly
Chest Pulse Wire
Book Holder
Power Cord Grommet
Frame
Catch Screw
Catch
Audio Wire
Walking Belt
15Ó Wire Harness
20Ó Wire Harness
Hand Weight
Endcap Spacer
Thick Base Pad
12Ó White Wire, M/F
8Ó White Wire, 2F
14Ó Blue Wire, 2F
4Ó Blue Wire, 2F
4Ó Black Wire, 2F
8Ó Green Wire, F/Ring
User's Manual
Foot Rail Cap Screw
Left Fait Rail Cap
Frame Pivot Bolt
Frame Pivot Spacer
Magnet
Front Roller/Pulley
Frame Pivot Nut
Reed Switch/Sensor
Wire
Latch Assembly
Reed Switch Clip
Lift Frame
Star Washer
Motor Assembly
Motor
Right Foot Rail Cap
Walking Platform
Platform Screw
Rear Platform Screw
Rear Isolator
Ground Screw/
Controller Screw
Ground Wire
Rear Endcap
Rear Roller Adj. Bolt
Warning Decal
Allen Wrench
Rear Roller
Optional Chest Pulse
Strap
Optional Chest Pulse
Left Foam Grip
Handrail Extension
1/2Ó Screw
Lock Knob
Upright
Lock Knob Sleeve
Spring
Lock Pin Collar
Pin Clip
Lock Pin
Right Foam Grip
Pulse Bar
99
100
101
102
103
104
105
106*
5
11*
12
13
14
15*
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
1
1
1
3
1
1
1
1
1
1
1
1
1
2
4
1
9
1
1
1
1
1
6
3
1
1
1
1
2
57
58
59
60
61
62
63**
1
1
2
1
1
1
1
Pulley/Flywheel/Fan
Motor Belt
107
108
109
110
111
112
113
114
115
116
117**
118
119
#
#
#
#
#
#
#
1
1
1
1
2
1
1
1
1
1
2
2
2
1
1
1
1
1
1
1
Motor Pivot Nut
Motor Tension Nut
Motor Tension Bolt
Motor Pivot Bolt
Hood
Incline Motor Bolt
Plastic Stand-Off
Power Board
Screw
64**
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
85
86
87
88
89
90
1
1
2
8
1
1
1
1
1
1
1
1
1
2
2
2
4
1
2
16
1
1
1
8
1
1
1
Choke
Controller
Electronics Plate
8Ó Wire Harness
Front Roller Adj. Bolt
1 1/4Ó Screw
Roller Washer
Front Roller Nut
Incline Motor
Incline Motor Stop
Belly Pan
Belly Pan Screw
(Long)
Static Decal
Circuit Breaker
Power Cord
On/Off Switch
Left Endcap Insert
Belt Guide Screw
Pulse Bar Washer
Pulse Bar Bolt
Upright Endcap
Belly Pan Screw
Console Base
Console
Console Screw
Key/Clip
10Õ iFit.com Wire
Jack
* Includes all parts shown in box
**For information about the optional
chest pulse sensor and hand
weights, see page 18
40
41
42
43
44
45
2
1
1
1
1
4
# These parts are not illustrated
Console Back Screw
Console Back
Releaseable Tie
Cable Tie Screw
23
Download from Www.Somanuals.com. All Manuals Search And Download.
EXPLODED DRAWINGÑModel No. PFTL79192
R0100A
Download from Www.Somanuals.com. All Manuals Search And Download.
EXPLODED DRAWINGÑModel No. PFTL79192
R0100A
Download from Www.Somanuals.com. All Manuals Search And Download.
ORDERING REPLACEMENT PARTS
To order replacement parts, call our Customer Service Department toll-free at 1-800-999-3756, Monday through
Friday, 6 a.m. until 6 p.m. Mountain Time (excluding holidays). When ordering parts, please be prepared to give
the following information:
¥ The MODEL NUMBER OF THE PRODUCT (PFTL79192)
¥ The NAME OF THE PRODUCT (PROFORM¨ 785Pi treadmill)
¥ The SERIAL NUMBER OF THE PRODUCT (see the front cover of this manual)
¥ The KEY NUMBER AND DESCRIPTION OF THE PART(S) (see the PART LIST on page 23 and the EXPLODED
DRAWING attached in the center of this manual).
If possible, place the treadmill near your telephone for easy reference when calling.
PROFORM is a registered trademark of ICON Health & Fitness, Inc.
LIMITED WARRANTY
ICON Health & Fitness, Inc. (ICON), warrants this product to be free from defects in workmanship and
material, under normal use and service conditions, for a period of ninety (90) days from the date of pur-
chase. This warranty extends only to the original purchaser. ICON's obligation under this warranty is lim-
ited to replacing or repairing, at ICON's option, the product at one of its authorized service centers. All
products for which warranty claim is made must be received by ICON at one of its authorized service
centers with all freight and other transportation charges prepaid, accompanied by sufficient proof of pur-
chase. All returns must be pre-authorized by ICON. This warranty does not extend to any product or
damage to a product caused by or attributable to freight damage, abuse, misuse, improper or abnormal
usage or repairs not provided by an ICON authorized service center, to products used for commercial or
rental purposes, or to products used as store display models. No other warranty beyond that specifically
set forth above is authorized by ICON.
ICON is not responsible or liable for indirect, special or consequential damages arising out of or in con-
nection with the use or performance of the product or damages with respect to any economic loss, loss
of property, loss of revenues or profits, loss of enjoyment or use, costs of removal, installation or other
consequential damages of whatsoever nature. Some states do not allow the exclusion or limitation of in-
cidental or consequential damages. Accordingly, the above limitation may not apply to you.
The warranty extended hereunder is in lieu of any and all other warranties and any implied warranties of
merchantability or fitness for a particular purpose is limited in its scope and duration to the terms set
forth herein. Some states do not allow limitations on how long an implied warranty lasts. Accordingly,
the above limitation may not apply to you.
This warranty gives you specific legal rights. You may also have other rights which vary from state to state.
ICON HEALTH & FITNESS, INC., 1500 S. 1000 W., LOGAN, UT 84321-9813
Part No. 162832 R0100A
Printed in USA © 2000 ICON Health & Fitness, Inc.
Download from Www.Somanuals.com. All Manuals Search And Download.
|