Model No. PFTL413040
Serial No.
USER'S MANUAL
Serial Number Decal
QUESTIONS?
If you have questions, or if there
are missing or damaged parts,
we will guarantee complete sat-
isfaction through direct assis-
tance from our factory.
TO AVOID DELAYS, PLEASE
CALL DIRECT TO OUR TOLL-
FREE CUSTOMER HOT LINE.
The trained technicians on our
Customer Hot Line will provide
immediate assistance, free of
charge to you.
CUSTOMER HOT LINE:
1-888-533-1333
Mon.–Fri., 6 a.m.–6 p.m. MST
CAUTION
Read all precautions and instruc-
tions in this manual before using
this equipment. Save this manual
for future reference.
Visit our website at
new products, prizes,
fitness tips, and much more!
Download from Www.Somanuals.com. All Manuals Search And Download.
IMPORTANT PRECAUTIONS
WARNING:
To reduce the risk of burns, fire, electric shock, or injury to persons, read the
following important precautions and information before operating the treadmill.
1. It is the responsibility of the owner to ensure
that all users of this treadmill are adequately
informed of all warnings and precautions.
tem is damaged, the walking belt may change
speed, accelerate, or stop unexpectedly,
which may result in a fall and serious injury.
2. Use the treadmill only as described in this
manual.
12. Keep the power cord and the surge suppres-
sor away from heated surfaces.
3. Place the treadmill on a level surface, with at
least eight feet of clearance behind it and two
feet on each side. Do not place the treadmill
on any surface that blocks air openings. To
protect the floor or carpet from damage, place
a mat under the treadmill.
13. Never move the walking belt while the power
is turned off. Do not operate the treadmill if
the power cord or plug is damaged, or if the
treadmill is not working properly. (See
BEFORE YOU BEGIN on page 5 if the tread-
mill is not working properly.)
4. Keep the treadmill indoors, away from mois-
ture and dust. Do not put the treadmill in a
garage or covered patio, or near water.
14. Never start the treadmill while you are stand-
ing on the walking belt. Always hold the
handrails while using the treadmill.
5. Do not operate the treadmill where aerosol
products are used or oxygen is administered.
15. The treadmill is capable of high speeds.
Adjust the speed in small increments to avoid
sudden jumps in speed.
6. Keep children under the age of 12 and pets
away from the treadmill at all times.
16. The pulse sensor is not a medical device.
Various factors, including the user's move-
ment, may affect the accuracy of heart rate
readings. The pulse sensor is intended only
as an exercise aid in determining heart rate
trends in general.
7. The treadmill should not be used by persons
weighing more than 300 pounds. Never allow
more than one person on the treadmill at a time.
8. Wear appropriate exercise clothes when
using the treadmill. Do not wear loose clothes
that could become caught in the treadmill.
Athletic support clothes are recommended
for both men and women. Always wear ath-
letic shoes. Never use the treadmill with bare
feet, wearing only stockings, or in sandals.
17. Never leave the treadmill unattended while it
is running. Always remove the key, unplug
the power cord, and move the reset/off circuit
breaker to the off position when the treadmill
is not in use. (See the drawing on page 5 for
the location of the circuit breaker.)
9. When connecting the power cord (see page 10),
plug the power cord into a surge suppressor
(not included) and plug the surge suppressor
into a grounded circuit capable of carrying 15
or more amps. No other appliance should be on
the same circuit. Do not use an extension cord.
18. Do not use the hand weights at speeds faster
than walking speeds. Using weights and not
holding the handrails may compromise your
ability to maintain your balance. Exercises
using weights should be attempted only by
experienced users.
10. Use only a single-outlet surge suppressor that
meets all of the specifications described on
page 10. To purchase a surge suppressor, see
your local PROFORM dealer or call 1-888-533-
1333 and order part number 146148, or see
your local electronics store.
19. Do not attempt to raise, lower, or move the
treadmill until it is properly assembled. (See
ASSEMBLY on page 6, and HOW TO FOLD
AND MOVE THE TREADMILL on page 21.)
You must be able to safely lift 45 pounds (20
kg) to raise, lower, or move the treadmill.
11. Failure to use a properly functioning surge
suppressor could result in damage to the con-
trol system of the treadmill. If the control sys-
20. When folding or moving the treadmill, make
sure that the storage latch is fully closed.
3
Download from Www.Somanuals.com. All Manuals Search And Download.
21. When using iFIT.com CDs and videos, an
electronic “chirping” sound will alert you
when the speed of the treadmill is about to
change. Always listen for the “chirp” and be
prepared for speed changes. In some in-
stances, the speed may change before the
personal trainer describes the change.
treadmill every three months.
25. Never drop or insert any object into any open-
ing.
26.
DANGER:
Always unplug the power
cord immediately after use, before cleaning
the treadmill, and before performing the main-
tenance and adjustment procedures de-
scribed in this manual. Never remove the
motor hood unless instructed to do so by an
authorized service representative. Servicing
other than the procedures in this manual
should be performed by an authorized service
representative only.
22. When using iFIT.com CDs and videos, you can
manually override the speed setting at any
time by pressing the speed buttons. However,
when the next “chirp” is heard, the speed will
change to the next setting of the CD or video
program.
23. Always remove iFIT.com CDs and videos from
your CD player or VCR when you are not
using them.
27. The treadmill is intended for in-home use
only. Do not use the treadmill in any
commercial, rental, or institutional setting.
24. Inspect and properly tighten all parts of the
WARNING:
Before beginning this or any exercise program, consult your physician. This
is especially important for persons over the age of 35 or persons with pre-existing health problems.
Read all instructions before using. ICON assumes no responsibility for personal injury or property
damage sustained by or through the use of this product.
SAVE THESE INSTRUCTIONS
The decals shown have been placed on your treadmill. If a decal is missing, or if it
is not legible, please call toll-free 1-888-533-1333 to order a free replacement decal.
Apply the decal in the location shown. Note: The decals are not shown at actual
size.
4
Download from Www.Somanuals.com. All Manuals Search And Download.
BEFORE YOU BEGIN
Thank you for selecting the revolutionary PROFORM®
445i treadmill. The PROFORM 445i treadmill combines
advanced technology with innovative design to help you
get the most from your exercise program in the conve-
nience and privacy of your home. And when you’re not
exercising, the unique PROFORM 445i treadmill can be
folded up, requiring less than half the floor space of
other treadmills.
Department toll-free at 1-888-533-1333, Monday
through Friday, 6 a.m. until 6 p.m. Mountain Time (ex-
cluding holidays). To help us assist you, please note
the product model number and serial number before
calling. The model number of the treadmill is
PFTL413040. The serial number can be found on a
decal attached to the treadmill (see the front cover of
this manual for the location).
For your benefit, read this manual carefully before
using the treadmill. If you have questions after read-
ing this manual, please call our Customer Service
Before reading further, please review the drawing
below and familiarize yourself with the labeled parts.
Fan
Tray
Console
Pulse Sensor
Handrail
Key/Clip
Reset/Off
Circuit Breaker
Walking Belt
Foot Rail
Power Cord
Cushioned Walking Platform
BACK
RIGHT SIDE
Rear Roller
Adjustment Bolts
5
Download from Www.Somanuals.com. All Manuals Search And Download.
ASSEMBLY
Assembly requires two persons. Set the treadmill in a cleared area and remove all packing materials. Do not
dispose of the packing materials until assembly is completed. Assembly requires the included allen wrench
and 90° screwdriver and your own Phillips screwdriver
and needlenose pliers
.
Note: The underside of the treadmill walking belt is coated with high-performance lubricant. During shipping, a
small amount of lubricant may be transferred to the top of the walking belt or the shipping carton. This is a normal
condition and does not affect treadmill performance. If there is lubricant on top of the walking belt, simply wipe off
the lubricant with a soft cloth and a mild, non-abrasive cleaner.
For help identifying the assembly hardware, see the drawings below. Note: The assembly hardware and other
small parts are packaged in separate part bags.
3/4” Screw (39)–6
1/2” Silver Screw (107)–1
Weight Rack Bolt (121)–4
Wheel Bolt (86)–2
2 1/2” Bolt (56)–4
1” Tek Screw (115)–4
Nut (122)–4
Washer (29)–4
Star Washer (81)–4
2 3/4” Bolt (47)–4
4” Bolt (120)–2
1. Make sure that the power cord is not plugged in.
1
115
With the help of a second person, carefully tip the
treadmill onto its left side. Partially fold the Frame (12) so
that the treadmill will be more stable. Do not fully fold
the treadmill until it is completely assembled.
97
97
82
Attach the four Base Pads (97) to the bottom of the Base
(82) with four 1” Tek Screws (115) (only two Base Pads
and 1” Tek Screws are shown.
12
115
6
Download from Www.Somanuals.com. All Manuals Search And Download.
2. Identify the Right Upright (10). Note: The Left Upright (9)
has the Latch Housing (77, see step 3) attached to it.
2
Have a second person hold the Right Upright (10) near the
Base (82) as shown. Orient the Right Upright so that it is
angled forward (see step 3). Feed the Upright Wire
Harness (17) into the lower end of the Right Upright and
out of the upper end.
10
17
86
Next, hold the Right Upright (10) against the Base (82). Be
careful not to pinch the wires. Insert two 2 3/4” Bolts
(47), with two Washers (29) and two Star Washers (81),
into the Base, and loosely thread the Bolts into the lower
end of the Right Upright (10).
81
47
29
82
95
9
Attach a Wheel (95) to the Base (82) with a Wheel Bolt (86).
Do not overtighten the Wheel Bolt; the Wheel must be
able to turn freely.
81
With the help of a second person, tip the treadmill onto its
right side. Be careful not to damage the Upright Wire
Harness (17). Have a second person hold the Left Upright
(9) near the Base (82). Orient the Left Upright so that it is
angled forward (see step 3). Attach the Left Upright and
the other Wheel (not shown) as described above. Note:
There are no wires in the Left Upright.
47
29
3. With the help of a second person, set the treadmill on the
floor with the Left and Right Uprights (9, 10) vertical.
3
56
Identify the Right Handrail (124), which has a large hole
in the left side. Feed the Wire Harness (17) up through
the hole in the bottom of the Right Handrail and out of
the large hole in the left side. Note: It may be helpful to
use needlenose pliers to pull the Wire Harness out of the
large hole.
17
56
123
9
Large
Hole
Set the Right Handrail (124) on the Right Upright (10).
Finger tighten a 4” Bolt (120) through the Right Upright into
the lower end of the Right Handrail. Attach the upper end
of the Right Handrail with a 2 1/2” Bolt (56). Do not
tighten the Bolts yet.
77
124
120
10
120
Attach the Left Handrail (123) as described above. Note:
There is not a wire in the Left Handrail.
7
Download from Www.Somanuals.com. All Manuals Search And Download.
4. Hold the Crossbar (88) between the Handrails (123,
124). Make sure that the square hole in the Crossbar is
on top as shown. Attach the Crossbar with two 2 1/2”
Bolts (56). Do not tighten the Crossbar Bolts yet.
4
123
88
56
124
Square
Hole
56
5. Attach the Weight Rack (125) to the brackets on the Left
and Right Uprights (9, 10) with four Weight Rack Bolts
(121) and four Nuts (122). Attach all of the Weight
Rack Bolts and Nuts before tightening any of them.
5
56
121
Firmly tighten the four 2 1/2” Bolts (56). Next, firmly
tighten the two 4” Bolts (120).
56
121
122
125
10
9
120
122
120
6. Have a second person hold the Console (78) near the
Right Upright (10). Attach the ground wire from the
Console to the Right Upright with the 1/2” Silver Screw
(107).
6
78
Ground
Wire
107
Connect the Upright Wire Harness (17) to the wire har-
ness on the Console (78). Make sure to connect the
connectors properly (see the inset drawing). The
connectors should slide together easily and snap
into place. IF THE CONNECTORS ARE NOT CON-
NECTED PROPERLY, THE CONSOLE MAY BE DAM-
AGED WHEN THE POWER IS TURNED ON. Insert the
connectors into the Console.
17
17
10
8
Download from Www.Somanuals.com. All Manuals Search And Download.
7. Set the Console (78) on the Left and Right Uprights (9,
10). Be careful not to pinch any wires. See drawing 6
on page 8. Make sure that the Upright Wire Harness (17)
is not in the small cutout shown by the arrow.
7
78
Using the included 90° screwdriver and a phillips screw-
driver, attach the Console (78) to the Uprights (9, 10) and
the Crossbar (88) with six 3/4” Screws (39). Start all six
Screws before tightening any of them; be careful not
to overtighten the Screws.
39
10
88
39
39
9
8. Lower the Uprights (9, 10) until the handrails are touch-
ing the floor.
8
9, 10
See the lower drawing. Position the Uprights (9, 10) so
that the treadmill Frame (12) is centered between the
Uprights.
47
Firmly tighten the four 2 3/4” Bolts (47). Then, raise the
Uprights (9, 10) back to the vertical position.
Handrail
Top View
10
9
9
12
9. Remove the knob from the pin. Make sure that the collar
and the spring are on the pin as shown. Insert the pin
into the Latch Housing (77), and tighten the knob back
onto the pin.
Knob
77
Collar
9
Pin
Spring
10. Make sure that all parts are properly tightened before you use the treadmill. Note: Extra hardware may
be included. Keep the included allen wrench in a secure place. The allen wrench is used to adjust the walking
belt (see page 24). To protect the floor or carpet, place a mat under the treadmill.
9
Download from Www.Somanuals.com. All Manuals Search And Download.
OPERATION AND ADJUSTMENT
TM
THE PERFORMANT LUBE WALKING BELT
tric shock. This product is equipped with a cord having
an equipment-grounding conductor and a grounding
plug. Plug the power cord into a surge suppressor,
and plug the surge suppressor into an appropriate
outlet that is properly installed and grounded in
accordance with all local codes and ordinances.
Important: The treadmill is not compatible with
GFCI-equipped outlets.
Your treadmill features a walking belt coated with high-
performance lubricant. IMPORTANT: Never apply sil-
icone spray or other substances to the walking
belt or the walking platform. Such substances will
deteriorate the walking belt and cause excessive
wear.
HOW TO PLUG IN THE POWER CORD
This product is for use on a nominal 120-volt circuit,
and has a grounding plug that looks like the plug illus-
trated in drawing 1 below. A temporary adapter that
looks like the adapter illustrated in drawing 2 may be
used to connect the surge suppressor to a 2-pole
receptacle as shown in drawing 2 if a properly
grounded outlet is not available.
DANGER:
Improper connection
of the equipment-grounding conductor can
result in an increased risk of electric shock.
Check with a qualified electrician or service-
man if you are in doubt as to whether the
product is properly grounded. Do not modify
the plug provided with the product—if it will
not fit the outlet, have a proper outlet
1
Grounded Outlet Box
Surge Suppressor
Grounding Pin
installed by a qualified electrician.
Your treadmill, like any other type of sophisticated
electronic equipment, can be seriously damaged by
sudden voltage changes in your home’s power.
Voltage surges, spikes, and noise interference can
result from weather conditions or from other appliances
being turned on or off. To decrease the possibility of
your treadmill being damaged, always use a surge
suppressor with your treadmill (see drawing 1 at
the right). To purchase a surge suppressor, see
your local PROFORM dealer or call 1-888-533-1333
and order part number 146148, or see your local
electronics store.
Grounding Pin
Grounded Outlet
Grounding Plug
2
Grounded Outlet Box
Adapter
Surge Suppressor
Use only a single-outlet surge suppressor that is
UL 1449 listed as a transient voltage surge sup-
pressor (TVSS). The surge suppressor must have a
UL suppressed voltage rating of 400 volts or less
and a minimum surge dissipation of 450 joules.
The surge suppressor must be electrically rated
for 120 volts AC and 15 amps. There must be a
monitoring light on the surge suppressor to indi-
cate whether it is functioning properly. Failure to
use a properly functioning surge suppressor could
result in damage to the control system of the
treadmill. If the control system is damaged, the
walking belt may change speed or stop unexpect-
edly, which may result in a fall and serious injury.
Lug
Metal Screw
The temporary adapter should be used only until a
properly grounded outlet (drawing 1) can be installed
by a qualified electrician.
The green-colored rigid ear, lug, or the like extending
from the adapter must be connected to a permanent
ground such as a properly grounded outlet box cover.
Whenever the adapter is used it must be held in place
by a metal screw. Some 2-pole receptacle outlet box
covers are not grounded. Contact a qualified elec-
trician to determine if the outlet box cover is
grounded before using an adapter.
This product must be grounded. If it should malfunc-
tion or break down, grounding provides a path of least
resistance for electric current to reduce the risk of elec-
10
Download from Www.Somanuals.com. All Manuals Search And Download.
CONSOLE DIAGRAM
Note: If there is a thin sheet of plastic
on the console, remove it.
Four speed programs are also offered. Each program
automatically controls the speed of the treadmill as it
guides you through an effective workout.
CAUTION:
Before operating the
console, read the following precautions.
The console also features new iFIT.com interactive
technology. Having iFIT.com technology is like having a
personal trainer in your home. Using the included audio
cable, you can connect the treadmill to your home
stereo, portable stereo, computer, or VCR and play
special iFIT.com CD and video programs (iFIT.com
CDs and videocassettes are available separately).
iFIT.com CD and video programs automatically control
the speed of the treadmill as a personal trainer coaches
you through every step of your workout. High-energy
music provides added motivation. To purchase
iFIT.com CDs or videocassettes, call toll-free
1-888-533-1333.
• Do not stand on the walking belt while turn-
ing on the power.
• Always wear the clip (see the drawing near
the top of page 12) while operating the
treadmill.
• Adjust the speed in small increments to
avoid sudden jumps in speed.
• To reduce the possibility of electric shock,
keep the console dry. Avoid spilling liquids
on the console and place only a sealed
water bottle in the water bottle holder.
With the treadmill connected to your computer, you
cess programs directly from the internet. Additional op-
tions are soon to be available. See www.iFIT.com for
more information.
FEATURES OF THE CONSOLE
The console offers a selection of features designed to
help you get the most from your exercise. When the
manual mode of the console is selected, the speed
and incline of the treadmill can be changed with the
touch of a button. As you exercise, the console will dis-
play continuous exercise feedback. You can even
measure your heart rate using the built-in pulse sensor.
To use the manual mode of the console, follow the
steps beginning on page 12. To use a speed program,
see page 14. To use an iFIT.com CD or video pro-
gram, see page 18. To use an iFIT.com program di-
rectly from our Web site, see page 19.
11
Download from Www.Somanuals.com. All Manuals Search And Download.
HOW TO TURN ON THE POWER
is held down, the speed setting will change in in-
crements of 0.5 mph.
Plug in the power cord (see page 10).
1
If one of the Quick Speed buttons is pressed, the
walking belt will gradually increase in speed until it
reaches the selected speed setting. Note: The
console can display speed and distance in ei-
ther miles or kilometers (see SPEED DISPLAY
on page 13). For simplicity, all instructions in
this section refer to miles.
Stand on the foot rails of the treadmill.
2
Find the clip at-
tached to the key,
and slide the clip
securely onto the
3
To stop the walking belt, press the Stop button.
The Time display will begin to flash. To restart the
walking belt, press the Start button or the Speed +
button.
waistband of your
clothes. Next, in-
Key
Clip
sert the key into
the console. After
a moment, the dis-
plays will light. Test the clip by carefully taking
a few steps backward until the key is pulled
from the console. If the key is not pulled from
the console, adjust the position of the clip.
Note: The first time you use the treadmill, periodi-
cally inspect the alignment of the walking belt, and
align it if necessary (see page 24).
Change the incline of the treadmill as desired.
4
5
To change the incline of the treadmill, press either
of the Incline buttons until the desired incline level
is reached.
HOW TO USE THE MANUAL MODE
Follow your progress with the displays.
Insert the key into the console.
1
Fat Calories/Calories/
Pulse display—This
display shows the ap-
See HOW TO TURN ON THE POWER above.
proximate number of fat
calories and calories
Select the manual mode.
2
you have burned (see
When the key is inserted, the manual mode will be
selected. If a program has been selected, press
the iFIT Speed button once or twice, until the indi-
cator beside the button is not lit.
FAT BURNING on page 25). The display will
change from one number to the next every few
seconds, as shown by the indicators in the display.
The display will also show your heart rate when
you use the pulse sensor (see step 6 on page 13).
Start the walking belt.
3
Time display—When
the manual mode or the
iFIT.com mode is se-
lected, this display will
To start the walking belt, press the Start button,
the Speed + button, or one of the ten Quick Speed
buttons.
show the elapsed time.
If the Start button or the Speed + button is
When a speed program
is selected, the display will show the time remain-
ing in the program.
pressed, the walking belt will begin to move at 1
mph. As you exercise, change the speed of the
walking belt as desired by pressing the Speed +
and – buttons. Each time a button is pressed, the
speed setting will change by 0.1 mph; if a button
12
Download from Www.Somanuals.com. All Manuals Search And Download.
Distance display—This
display shows the dis-
tance that you have
walked or run.
When your pulse is de-
tected, the heart-shaped
indicator in the Fat
Calories/Calories/Pulse
display will flash each
time your heart beats,
Speed display—This
display shows the speed
of the walking belt.
and your heart rate will be shown. For the most
accurate heart rate reading, hold your thumbs
on the pulse sensors for about 15 seconds.
If the displayed heart rate appears to be too high
or too low, or if your heart rate is not displayed, lift
your thumbs off the pulse sensors for a few sec-
onds. Then, place your thumbs on the pulse sen-
sors as described above. Remember to stand still
while measuring your heart rate.
Note: The console can
show speed and dis-
tance in either miles or
kilometers. The letters
“MPH” or “KPH” will ap-
pear in the Speed display
Turn on the fan if desired.
7
8
to show which unit of measurement is selected. To
change the unit of measurement, first hold down
the Stop button, insert the key into the console,
and continue to hold the Stop button for a few sec-
onds. An “E” (for English) or an “M” (for metric) will
appear in the display. Press the Speed + button to
change the unit of measurement. When the de-
sired unit of measurement is selected, remove the
key and then reinsert it.
To turn on the fan at low
speed, press the fan but-
ton. To turn on the fan at
high speed, press the but-
ton a second time. To
Fan
Button
turn off the fan, press the
button a third time. Note: Any time that the walking
belt is stopped for a few minutes, the fan will auto-
matically turn off.
To reset the displays, press the Stop button, re-
move the key, and then reinsert the key.
When you are finished exercising, remove the
key.
Measure your heart rate, if desired.
6
Step onto the foot rails and press the Stop button.
Adjust the incline of the treadmill to the lowest
setting. Next, remove the key from the console and
put it in a secure place.
To measure
Pulse Sensors
your heart rate,
stand on the
foot rails and
place your
thumbs on the
pulse sensors.
Do not press
too hard, or
the circulation
in your thumbs will be restricted and your
pulse will not be detected.
13
Download from Www.Somanuals.com. All Manuals Search And Download.
To change the incline of the treadmill during the
program, press the Incline buttons until the de-
sired incline level is reached.
HOW TO USE A SPEED PROGRAM
Insert the key fully into the console.
1
The program will continue until no time remains in
the Time display. The walking belt will then slow
to a stop.
See HOW TO TURN ON THE POWER on page
12.
Note: If the speed setting for the current period is
too high or too low, you can manually override the
setting by pressing the Speed buttons. Important:
When the current period of the program ends,
the treadmill will automatically adjust to the
speed setting for the next period.
Select a speed program.
2
When the key is in-
serted, the manual
mode will be selected.
To select a speed pro-
gram, press the Speed
Programs button re-
To stop the program temporarily, press the Stop
button. The Time display will begin to flash. To
restart the program, press the Start button or the
Speed + button. To end the program, press the
Stop button, remove the key, and then reinsert the
key.
peatedly until one of the four speed program indi-
cators lights. When a speed program is selected,
the Time display will show how long the program
will last, and the Speed display will flash the maxi-
mum speed setting for the program for a few sec-
onds.
Follow your progress with the displays.
See step 5 on page 12.
4
5
6
7
Press the Start button or the Speed + button to
start the program.
3
Measure your heart rate, if desired.
See step 6 on page 13.
A moment after the button is pressed, the tread-
mill will automatically adjust to the first speed set-
ting for the program. Hold the handrails and begin
walking.
Turn on the fan if desired.
See step 7 on page 13.
Each program is divided into several time periods
of different lengths. One speed setting is pro-
grammed for each period. Note: The same speed
setting may be programmed for two or more con-
secutive periods.
When the program is completed, remove the
key from the console.
When only a few seconds remain in the first pe-
riod of the program, the Speed display will flash
and a series of tones will sound. The treadmill will
then automatically adjust to the speed setting for
the second period. Note: When the same speed
setting is programmed for consecutive periods, the
Speed display will not flash during the last three
seconds of the current period.
When the program has ended, adjust the incline
of the treadmill to the lowest setting. Next, re-
move the key from the console and put it in a safe
place.
14
Download from Www.Somanuals.com. All Manuals Search And Download.
HOW TO CONNECT YOUR PORTABLE STEREO
HOW TO CONNECT THE TREADMILL TO YOUR
CD PLAYER, VCR, OR COMPUTER
Note: If your stereo has an RCA-type AUDIO OUT
jack, see instruction A below. If your stereo has a
3.5mm LINE OUT jack, see instruction B. If your
stereo has only a PHONES jack, see instruction C.
To use iFIT.com CDs, the treadmill must be connected
to your portable CD player, portable stereo, home
stereo, or computer with CD player. See pages 15 and
16 for connecting instructions. To use iFIT.com video-
cassettes, the treadmill must be connected to your
VCR. See page 17 for connecting instructions. To use
iFIT.com programs directly from our internet site,
the treadmill must be connected to your home com-
puter. See page 16 for connecting instructions.
A. Plug one end of the audio cable into the jack on the
front of the treadmill near the power cord. Plug the
other end of the cable into the included adapter. Plug
the adapter into an AUDIO OUT jack on your stereo.
A
HOW TO CONNECT YOUR PORTABLE CD PLAYER
AUDIO OUT
RIGHT
LEFT
Note: If your CD player has separate LINE OUT and
PHONES jacks, see instruction A below. If your CD
player has only one jack, see instruction B.
Adapter
Audio
Cable
A. Plug one end of the audio cable into the jack on the
front of the treadmill near the power cord. Plug the
other end of the cable into the LINE OUT jack on
your CD player. Plug your headphones into the
PHONES jack.
B. Plug one end of the audio cable into the jack on the
front of the treadmill near the power cord. Plug the
other end of the cable into the LINE OUT jack on
your stereo.
A
PHONES LINE OUT
LINE OUT
PHONES
B
Head-
phones
LINE OUT
Audio
Cable
Audio
Cable
B. Plug one end of the audio cable into the jack on the
front of the treadmill near the power cord. Plug the
other end of the cable into a 3.5mm Y-adapter (avail-
able at electronics stores). Plug the Y-adapter into
the PHONES jack on your CD player. Plug your
headphones into the other side of the Y-adapter.
C. Plug one end of the audio cable into the jack on the
front of the treadmill near the power cord. Plug the
other end of the cable into a 3.5mm Y-adapter
(available at electronics stores). Plug the Y-adapter
into the PHONES jack on your stereo. Plug your
headphones into the other side of the Y-adapter.
B
PHONES
C
PHONES
3.5mm
Y-adapter
PHONES
Audio
Cable
3.5mm
Y-adapter
Audio
Cable
Headphones
Headphones
15
Download from Www.Somanuals.com. All Manuals Search And Download.
HOW TO CONNECT YOUR HOME STEREO
HOW TO CONNECT YOUR COMPUTER
Note: If your stereo has an unused LINE OUT jack,
see instruction A below. If the LINE OUT jack is
being used, see instruction B.
Note: If your computer has a 3.5mm LINE OUT jack,
see instruction A. If your computer has only a
PHONES jack, see instruction B.
A. Plug one end of the audio cable into the jack on the
front of the treadmill near the power cord. Plug the
other end of the cable into the included adapter.
Plug the adapter into the LINE OUT jack on your
stereo.
A. Plug one end of the audio cable into the jack on the
front of the treadmill near the power cord. Plug the
other end of the cable into the LINE OUT jack on
your computer.
A
A
CD
LINE OUT
VCR
Amp
LINE OUT
Audio
Cable
LINE OUT
Adapter
Audio
Cable
B. Plug one end of the audio cable into the jack on the
front of the treadmill near the power cord. Plug the
other end of the cable into a 3.5mm Y-adapter
(available at electronics stores). Plug the Y-adapter
into the PHONES jack on your computer. Plug your
headphones or speakers into the other side of the
Y-adapter.
B. Plug one end of the audio cable into the jack on the
front of the treadmill near the power cord. Plug the
other end of the cable into the included adapter.
Plug the adapter into an RCA Y-adapter (available
at electronics stores). Next, remove the wire that is
currently plugged into the LINE OUT jack on your
stereo and plug the wire into the unused side of the
Y-adapter. Plug the Y-adapter into the LINE OUT
jack on your stereo.
B
PHONES
B
CD
Audio
Cable
3.5mm
Y-adapter
VCR
Amp
LINE OUT
Headphones/Speakers
RCA
Y-adapter
Audio
Cable
Adapter
Wire removed from
LINE OUT jack
16
Download from Www.Somanuals.com. All Manuals Search And Download.
HOW TO CONNECT YOUR VCR
B. Plug one end of the audio cable into the jack on the
front of the treadmill near the power cord. Plug the
other end of the cable into the included adapter.
Plug the adapter into an RCA Y-adapter (available
at electronics stores). Next, remove the wire that is
currently plugged into the AUDIO OUT jack on your
VCR and plug the wire into the unused side of the
Y-adapter. Plug the Y-adapter into the AUDIO OUT
jack on your VCR.
Note: If your VCR has an unused AUDIO OUT jack,
see instruction A below. If the AUDIO OUT jack is
being used, see instruction B. If you have a TV
with a built-in VCR, see instruction B. If your VCR
is connected to your home stereo, see HOW TO
CONNECT YOUR HOME STEREO on page 16.
A. Plug one end of the audio cable into the jack on the
front of the treadmill near the power cord. Plug the
other end of the cable into the included adapter.
Plug the adapter into the AUDIO OUT jack on your
VCR.
B
ANT IN
.
VIDEO AUDIO
IN
RF OUT
CH
3
4
OUT
A
ANT IN
.
RCA Y-adapter
Audio
VIDEO AUDIO
IN
RF OUT
CH
3
4
OUT
AUDIO OUT
Adapter
Cable
RIGHT
LEFT
Adapter
Wire removed from
AUDIO OUT jack
Audio
Cable
17
Download from Www.Somanuals.com. All Manuals Search And Download.
If the speed setting is too high or too low, you can
manually override the setting at any time by
pressing the Speed buttons on the console.
However, when the next “chirp” is heard, the
speed will change to the next setting of the CD
or video program.
HOW TO USE IFIT.COM CD AND VIDEO
PROGRAMS
To use iFIT.com CDs or videocassettes, the treadmill
must be connected to your portable CD player, portable
stereo, home stereo, computer with CD player, or
VCR. See HOW TO CONNECT THE TREADMILL TO
YOUR CD PLAYER, VCR, OR COMPUTER on pages
15 to 17. Note: IFIT.com CD and video programs will
control only the speed of your treadmill.
To stop the walking belt at any time, press the
Stop button on the console. The Time display will
begin to flash. To restart the program, press the
Start button or the Speed + button. After a mo-
ment, the walking belt will begin to move. When
the next “chirp” is heard, the speed will
change to the next setting of the CD or video
program.
To purchase iFIT.com CDs or videocassettes, call
toll-free 1-888-533-1333.
Follow the steps below to use an iFIT.com CD or video
program.
When the CD or video program is completed, the
walking belt will stop and the Time display will
begin to flash. Note: To use another CD or video
program, press the Stop button or remove the key
and go to step 1.
Insert the key into the console.
1
See HOW TO TURN ON THE POWER on page 12.
Note: If the speed of the treadmill does not
change when a “chirp” is heard:
Select the iFIT.com mode.
2
• Make sure that the iFIT.com indicator is lit and
that the Time display is not flashing. If the
Time display is flashing, press the Start button
or the Speed + button on the console.
When the key is in-
serted, the manual
mode will be selected.
To use iFIT.com CDs
or videocassettes,
press the iFIT Speed
button. The indicator beside the button will light.
• Adjust the volume of your CD player or VCR.
If the volume is too high or too low, the con-
sole may not detect the program signals.
Insert the iFIT.com CD or videocassette.
• Make sure that the audio cable is properly
connected, that it is fully plugged in, and that
it is not wrapped around a power cord.
3
If you are using an iFIT.com CD, insert the CD
into your CD player. If you are using an iFIT.com
videocassette, insert the videocassette into your
VCR.
Follow your progress with the displays.
See step 5 on page 12.
5
6
7
8
Press the PLAY button on your CD player or
VCR.
4
Measure your heart rate, if desired.
See step 6 on page 13.
A moment after the button is pressed, your per-
sonal trainer will begin guiding you through your
workout. Simply follow your personal trainer’s
instructions. Note: If the Time display is flashing,
press the Start button or the Speed + button on
the console. The treadmill will not respond to a
CD or video program when the Time display is
flashing.
Turn on the fan if desired.
See step 7 on page 13.
When the program is completed, remove the
key.
During the CD or video program, an electronic
“chirping” sound will alert you when the speed of
the treadmill is about to change. CAUTION:
Always listen for the “chirp” and be prepared
for speed changes. In some instances, the
speed may change before the personal trainer
describes the change.
See step 7 on page 14.
CAUTION: Always remove iFIT.com CDs and
videocassettes from your CD player or VCR
when you are finished using them.
18
Download from Www.Somanuals.com. All Manuals Search And Download.
will begin and the walking belt will begin to move.
Hold the handrails, step onto the walking belt, and
begin walking. During the program, an electronic
“chirping” sound will alert you when the speed of
the treadmill is about to change. CAUTION:
Always listen for the “chirp” and be prepared
for speed changes.
HOW TO USE PROGRAMS DIRECTLY FROM
OUR WEB SITE
for details. Note: Programs will control only the
speed of your treadmill.
If the speed setting is too high or too low, you can
manually override the setting at any time by press-
ing the Speed buttons on the console. However,
when the next “chirp” is heard, the speed will
change to the next setting for the program.
To use programs from our Web site, the treadmill must
be connected to your home computer. See HOW TO
CONNECT YOUR COMPUTER on page 16. In
addition, you must have an internet connection and
an internet service provider. A list of specific system re-
quirements is found on our Web site.
To stop the walking belt at any time, press the
Stop button on the console. The Time display will
begin to flash. To restart the program, press the
Start button or the Speed + button. After a mo-
ment, the walking belt will begin to move. When
the next “chirp” is heard, the speed will change
to the next setting for the program.
Follow the steps below to use a program from our
Web site.
Insert the key into the console.
1
See HOW TO TURN ON THE POWER on page 12.
When the program is completed, the walking belt
will stop and the Time display will begin to flash.
Note: To use another program, press the Stop
button and go to step 5.
Select the iFIT.com mode.
2
When the key is in-
serted, the manual
Note: If the speed of the treadmill does not
change when a “chirp” is heard, make sure that
the iFIT.com indicator is lit and that the Time
display is not flashing. In addition, make sure
that the audio cable is properly connected, that
it is fully plugged in, and that it is not wrapped
around a power cord.
mode will be selected.
To use a program from
our Web site, press the
iFIT Speed button. The
indicator beside the button will light.
Go to your computer and start an internet
3
connection.
Follow your progress with the displays.
See step 5 on page 12.
8
9
Start your web browser, if necessary, and go to
4
Measure your heart rate, if desired.
See step 6 on page 13.
Follow the desired links on our Web site to se-
lect a program.
5
Read and follow the on-line instructions for using a
program.
10 Turn on the fan if desired.
See step 7 on page 13.
Follow the on-line instructions to start the
6
program.
When the program is completed, remove the
key.
11
When you start the program, an on-screen count-
down will begin.
See step 7 on page 14.
Return to the treadmill and stand on the foot
rails. Find the clip attached to the key and slide
the clip onto the waistband of your clothes.
7
When the on-screen countdown ends, the program
19
Download from Www.Somanuals.com. All Manuals Search And Download.
THE INFORMATION MODE
The Distance display will show
the total number of miles (or
kilometers) that the walking
belt has moved.
The console features an information mode that keeps
track of the total number of hours that the treadmill has
been operated and the total number of miles that the
walking belt has moved. The information mode also al-
lows you to switch the console from miles per hour to
kilometers per hour.
An “E” (for English) or an “M”
(for metric) will appear in the
Speed display. Press the
Speed + button to change the
unit of measurement.
To select the information mode, hold down the Stop
button, insert the key into the console, and continue to
hold the Stop button for a few seconds. When the infor-
mation mode is selected, the following information will
be shown:
To exit the information mode, remove the key from the
console.
The Time display will show the
total number of hours that the
treadmill has been used.
20
Download from Www.Somanuals.com. All Manuals Search And Download.
HOW TO FOLD AND MOVE THE TREADMILL
HOW TO FOLD THE TREADMILL FOR STORAGE
Before folding the treadmill, adjust the incline to the
lowest position. If this is not done, the treadmill may be
permanently damaged. Next, unplug the power cord.
CAUTION: You must be able to safely lift 45 pounds (20
kg) to raise, lower, or move the treadmill.
1. Hold the treadmill with your hands in the locations shown
at the right. CAUTION: To decrease the possibility of
injury, bend your legs and keep your back straight. As
you raise the treadmill, make sure to lift with your legs
rather than your back. Raise the treadmill about halfway
to the vertical position.
2. Move your right hand to the position shown and hold the
treadmill firmly. Using your left hand, pull the latch knob
to the left and hold it. Raise the treadmill until the hole in
the frame is aligned with the pin on the latch knob. Slowly
release the latch knob. Make sure that the frame is held
by the pin.
Open
To protect the floor or carpet from damage, place a
mat under the treadmill. Keep the treadmill out of
direct sunlight. Do not leave the treadmill in the stor-
age position in temperatures above 85° Fahrenheit.
Latch
Knob
Closed
Pin
Frame
HOW TO MOVE THE TREADMILL
Before moving the treadmill, convert the treadmill to the stor-
age position as described above. Make sure that the frame
is securely held by the pin on the latch knob.
1. Hold the upright as shown and place one foot against a
wheel.
2. Tilt the treadmill back until it rolls freely on the wheels.
Carefully move the treadmill to the desired location.
Never move the treadmill without tipping it back. To
reduce the risk of injury, use extreme caution while
moving the treadmill. Do not attempt to move the
treadmill over an uneven surface.
3. Place one foot on a wheel, and carefully lower the tread-
mill until it is resting in the storage position.
Base
Wheels
21
Download from Www.Somanuals.com. All Manuals Search And Download.
HOW TO LOWER THE TREADMILL FOR USE
1. Hold the upper end of the treadmill with your right hand
as shown. Using your left hand, pull the latch knob to the
left and hold it. Pivot the treadmill down until the frame is
past the pin. Slowly release the latch knob.
Latch
Knob
Open
Pin
Frame
2. Hold the treadmill firmly with both hands, and lower the
treadmill to the floor. Do not drop the treadmill frame
to the floor. CAUTION: To decrease the possibility of
injury, bend your legs and keep your back straight.
22
Download from Www.Somanuals.com. All Manuals Search And Download.
TROUBLESHOOTING
Most treadmill problems can be solved by following the steps below. Find the symptom that applies, and
follow the steps listed. If further assistance is needed, please call our Customer Service Department toll-
free at 1-888-533-1333, Monday through Friday, 6 a.m. until 6 p.m. Mountain Time (excluding holidays).
PROBLEM: The power does not turn on
SOLUTION: a. Make sure that the power cord is plugged into a surge suppressor, and that the surge suppressor
is plugged into a properly grounded outlet (see page 10). Use only a single-outlet surge suppres-
sor that meets all of the specifications described on page 10. Important: The treadmill is not com-
patible with GFCI-equipped outlets.
b. After the power cord has been plugged in, make sure that the key is fully inserted into the console.
c. Check the reset/off circuit breaker located on the
c
treadmill near the power cord. If the switch protrudes
as shown, the circuit breaker has tripped. To reset
the circuit breaker, wait for five minutes and then
press the switch back in.
Tripped
Reset
PROBLEM: The power turns off during use
SOLUTION: a. Check the reset/off circuit breaker located on the treadmill frame near the power cord (see c.
above). If the circuit breaker has tripped, wait for five minutes and then press the switch back in.
b. Make sure that the power cord is plugged in. If the power cord is plugged in, unplug it, wait for
five minutes, and then plug it back in.
c. Remove the key from the console. Reinsert the key into the console.
d. If the treadmill still will not run, please call our Customer Service Department, toll-free.
PROBLEM: The speed display on the console does not function properly
SOLUTION: a. Remove the key and UNPLUG THE POWER CORD.
Remove the Hood Screws (58) and the Hood (94)
58
from the treadmill.
58
94
58
Locate the Reed Switch (21) and the Magnet (43) on
the left side of the Pulley (42). Turn the Pulley until the
Magnet is aligned with the Reed Switch. Make sure
that the gap between the Magnet and the Reed
Switch is about 1/8”. If necessary, loosen the Screw
(62), move the Reed Switch slightly, and then
retighten the Screw. Reattach the hood, and run the
treadmill for a few minutes to check for a correct
speed reading.
1/8”
42
43
62
21
Top
View
23
Download from Www.Somanuals.com. All Manuals Search And Download.
PROBLEM: The walking belt slows when walked on
SOLUTION: a. Use only a single-outlet surge suppressor that meets all of the specifications described on page 10.
b. If the walking belt is overtightened, treadmill perfor-
b
mance may decrease and the walking belt may be-
come damaged. Remove the key and UNPLUG THE
POWER CORD. Using the allen wrench, turn both
3”–4”
rear roller adjustment bolts counterclockwise 1/4 of a
turn. When the walking belt is properly tightened, you
should be able to lift each side of the walking belt 3 to
4 inches off the walking platform. Be careful to keep
the walking belt centered. Plug in the power cord, in-
sert the key, and run the treadmill for a few minutes.
Rear Roller Adjustment Bolts
Repeat until the walking belt is properly tightened.
c. If the walking belt still slows when walked on, please
call our Customer Service Department, toll-free.
PROBLEM: The walking belt is off-center or slips when walked on
SOLUTION: a. If the walking belt is off-center, first remove the key
a
and UNPLUG THE POWER CORD. If the walking
belt has shifted to the left, use the allen wrench to
turn the left rear roller bolt clockwise 1/2 of a turn; if
the walking belt has shifted to the right, turn the
bolt counterclockwise 1/2 of a turn. Be careful not to
overtighten the walking belt. Plug in the power cord,
insert the key, and run the treadmill for a few minutes.
Repeat until the walking belt is centered.
b. If the walking belt slips when walked on, first remove
b
the key and UNPLUG THE POWER CORD. Using
the allen wrench, turn both rear roller bolts clockwise,
1/4 of a turn. When the walking belt is correctly tight-
ened, you should be able to lift each side of the walk-
ing belt 3 to 4 inches off the walking platform. Be
careful to keep the walking belt centered. Plug in the
power cord, insert the key, and carefully walk on the
treadmill for a few minutes. Repeat until the walking
belt is properly tightened.
24
Download from Www.Somanuals.com. All Manuals Search And Download.
CONDITIONING GUIDELINES
ergy. Only after the first few minutes does your body
begin to use stored fat calories for energy. If your goal
is to burn fat, adjust the speed or incline of the tread-
mill until your heart rate is near the lowest number in
your training zone.
WARNING:
Before beginning this
or any exercise program, consult your physi-
cian. This is especially important for individu-
als over the age of 35 or individuals with pre-
existing health problems.
For maximum fat burning, adjust the speed or incline
of the treadmill until your heart rate is near the middle
number in your training zone.
The pulse sensor is not a medical device.
Various factors, including the user's move-
ment, may affect the accuracy of heart rate
readings. The pulse sensor is intended only
as an exercise aid in determining heart rate
trends in general.
Aerobic Exercise
If your goal is to strengthen your cardiovascular sys-
tem, your exercise must be “aerobic.” Aerobic exercise
is activity that requires large amounts of oxygen for
prolonged periods of time. This increases the demand
on the heart to pump blood to the muscles, and on the
lungs to oxygenate the blood. For aerobic exercise,
adjust the speed or incline of the treadmill until your
heart rate is near the highest number in your training
zone.
The following guidelines will help you to plan your ex-
ercise program. For more detailed exercise informa-
tion, obtain a reputable book or consult your physician.
EXERCISE INTENSITY
Whether your goal is to burn fat or to strengthen your
cardiovascular system, the key to achieving the
WORKOUT GUIDELINES
desired results is to exercise with the proper intensity.
The proper intensity level can be found by using your
heart rate as a guide. The chart below shows recom-
mended heart rates for fat burning and aerobic exercise.
Each workout should include the following three parts:
A Warm-up—Start each workout with 5 to 10 minutes
of stretching and light exercise. A proper warm-up in-
creases your body temperature, heart rate and circula-
tion in preparation for exercise.
Training Zone Exercise—After warming up, increase
the intensity of your exercise until your pulse is in your
training zone for 20 to 60 minutes. (During the first few
weeks of your exercise program, do not keep your
pulse in your training zone for longer than 20 minutes.)
Breathe regularly and deeply as you exercise—never
hold your breath.
To find the proper heart rate for you, first find your age
near the bottom of the chart (ages are rounded off to
the nearest ten years). Next, find the three numbers
above your age. The three numbers define your “train-
ing zone.” The lower two numbers are recommended
heart rates for fat burning; the highest number is the
recommended heart rate for aerobic exercise.
A Cool-down—Finish each workout with 5 to 10 min-
utes of stretching to cool down. This will increase the
flexibility of your muscles and will help prevent post-ex-
ercise problems.
EXERCISE FREQUENCY
To measure your heart rate during exercise, use the
handgrip pulse sensor.
To maintain or improve your condition, complete three
workouts each week, with at least one day of rest be-
tween workouts. After a few months, you may com-
plete up to five workouts each week if desired. The key
to success is to make exercise a regular and enjoyable
part of your everyday life.
Fat Burning
To burn fat effectively, you must exercise at a relatively
low intensity level for a sustained period of time.
During the first few minutes of exercise, your body
uses easily accessible carbohydrate calories for en-
25
Download from Www.Somanuals.com. All Manuals Search And Download.
SUGGESTED STRETCHES
1
The correct form for several basic stretches is shown at the right.
Move slowly as you stretch—never bounce.
1. Toe Touch Stretch
Stand with your knees bent slightly and slowly bend forward from
your hips. Allow your back and shoulders to relax as you reach
down toward your toes as far as possible. Hold for 15 counts, then
relax. Repeat 3 times. Stretches: Hamstrings, back of knees, and
back.
2
2. Hamstring Stretch
Sit with one leg extended. Bring the sole of the opposite foot toward
you and rest it against the inner thigh of your extended leg. Reach
toward your toes as far as possible. Hold for 15 counts, then relax.
Repeat 3 times for each leg. Stretches: Hamstrings, lower back,
and groin.
3
3. Calf/Achilles Stretch
With one leg in front of the other, reach forward and place your
hands against a wall. Keep your back leg straight and your back
foot flat on the floor. Bend your front leg, lean forward and move
your hips toward the wall. Hold for 15 counts, then relax. Repeat 3
times for each leg. To cause further stretching of the achilles ten-
dons, bend your back leg as well. Stretches: Calves, achilles ten-
dons, and ankles.
4
4. Quadriceps Stretch
With one hand against a wall for balance, reach back and grasp
one foot with your other hand. Bring your heel as close to your but-
tocks as possible. Hold for 15 counts, then relax. Repeat 3 times for
both legs. Stretches: Quadriceps and hip muscles.
5
5. Inner Thigh Stretch
Sit with the soles of your feet together and your knees outward. Pull
your feet toward your groin area as far as possible. Hold for 15
counts, then relax. Repeat 3 times. Stretches: Quadriceps and hip
muscles.
26
Download from Www.Somanuals.com. All Manuals Search And Download.
NOTES
27
Download from Www.Somanuals.com. All Manuals Search And Download.
PART LIST—Model No. PFTL413040
R1004B
To locate the parts listed below, see the EXPLODED DRAWING on pages 29 to 31.
Key
Key
Key
No. Qty. Description
No. Qty. Description
No. Qty. Description
1
2
3
1
1
4
1
Motor Belt
Pulley/Flywheel/Fan
Motor Nut
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
4
2
2
4
2
2
1
1
1
3
4
1
4
1
4
2
1
1
20
1
1
2
1
1
2
3
1
1
5
1
1
2
6
1
1
1
2
8
1
2
2
Platform Screw
Isolator
Center Platform Screw 90
2 3/4” Bolt
3-lb. Weight
Belt Guide
Fan
Front Belly Pan
Small Nut
Cable Tie Clamp
Cable Tie
Walking Belt
2 1/2” Bolt
Rear Roller
Hood Screw
Rear Foot
iFIT Jack
Ground Wire
Screw
Left Rear Endcap
Right Rear Endcap
Rear Roller Adj. Bolt
Motor
Latch Decal
Foot Rail Cover
Small Star Washer
Incline Disk
Walking Platform
8” Cable Tie
Incline Bolt
Motor Tension Bolt
Right Foot Rail
Belly Pan Screw
Latch Housing
Console
Stop Bracket
Incline Pivot Nut
Star Washer
Base
88
89
1
1
1
1
2
1
1
2
1
4
1
1
1
8
2
1
4
2
2
1
1
1
2
1
2
1
2
4
2
1
1
2
2
4
4
1
1
1
2
1
1
1
Console Crossbar
Static Decal
Key/Clip
Incline Motor Belly Pan
Roller Adj. Washer
Book Holder
Motor Hood
Front Wheel
Incline Motor Shield
Base Pad
4*
Motor/Pulley/
91
92
93
94
95
96
97
98
99
Flywheel/ Fan
Incline Motor Bolt
Controller Wire
Incline Motor
Filter Wire
Left Upright
Right Upright
Console Plate
Frame
Fan Cover
Fan Screw
Incline Motor Nut
Belt Guide Screw
Upright Wire Harness
Hood Bracket
Front Hood Bracket
Warning Decal
Reed Switch
Reed Switch Clip
Left Handrail
Controller
Electronics Bracket
Reset/Off
Circuit Breaker
Power Cord
Power Cord Grommet
Washer
5
6
7
8
1
1
1
1
1
1
1
1
1
2
4
4
1
2
1
2
1
1
1
1
1
1
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
iFIT Wire
Upright Grommet
Allen Wrench
3/4” Tek Screw
Controller Screw
Power Board Plate
Base Cap
Incline Pivot Nut
2-lb. Weight
1/2” Silver Screw
Audio Wire Nut
Audio Wire
1” Spacer
Hood Spacer
Bumper
Edge Guard
1/2” Spacer
1” Tek Screw
Belly Pan Interface
Photo Switch
Small Bolt
100
101
102
103
104
105
106
107
108
109
110
111
112
113
114
115
116
117
118
119
120
121
122
123
124
125
126
#
27
28
29
30*
31
32
33
34
35
36
37
38
39
40
41
42
43
1
1
8
1
1
2
2
1
1
1
1
4
10
1
1
1
1
Latch Assembly
Incline Frame
Frame Pivot Bolt
Frame Pivot Spacer
Tension Bushing
Front Roller Adj. Bolt
Foot Rail Cap (Right)
Motor Tension Nut
Motor Bolt
U-Nut
4” Bolt
Weight Rack Bolt
Nut
Left Handrail
Right Handrail
Weight Rack
1-lb. Weight
4” Blue Wire, 2F
8” Green Wire, 2 Ring
User's Manual
Incline Frame Bolt
Motor Tension
Washer
Latch Screw
Wheel Bolt
3/4” Screw
#
#
Foot Rail Cap (Left)
Left Foot Rail
Front Roller/Pulley
Magnet
85
86
87
2
2
1
* Includes all parts shown in the box
# These parts are not illustrated
Console Base
28
Download from Www.Somanuals.com. All Manuals Search And Download.
EXPLODED DRAWING—Model No. PFTL413040
R1004B
29
Download from Www.Somanuals.com. All Manuals Search And Download.
EXPLODED DRAWING—Model No. PFTL413040 Part 2 of 3
R1004B
58
58
94
89
58
4*
37
3
66
113
1
2
58
79
3
27
7
62
24
52
69
5
26
62
25
28
117
118
105
15
114
16
110
62
70
34
103
74
18
84
62
22
19
111
62
69
21
108
109
80
105
31
110
8
81
62
73
81
15
35
38
38
18
33
80
76
76
76
116
98
60
6
116
76
51
76
30
Download from Www.Somanuals.com. All Manuals Search And Download.
EXPLODED DRAWING—Model No. PFTL413040 Part 3 of 3
R1004B
14
78
39
50
126
56
119
56
39
39
106
39
121
11
13
88
39
56
123
107
30
39
119
17
122
77
56
121
85
125
39
120
48
91
124
122
10
83
86
95
9
120
101
101
17
99
97
83
112
82
115
20
95
81
29
97
115
47
101
104
86
101
112
97
115
20
96
97
115
81
72
29
104
47
31
Download from Www.Somanuals.com. All Manuals Search And Download.
HOW TO ORDER REPLACEMENT PARTS
To order replacement parts, call our Customer Service Department toll-free at 1-888-533-1333, Monday through
Friday, 6 a.m. until 6 p.m. Mountain Time (excluding holidays). Before calling, please note the following
information:
• The MODEL NUMBER of the product (PFTL413040)
• The NAME of the product (PROFORM® 445i treadmill)
• The SERIAL NUMBER of the product (see the front cover of this manual)
• The KEY NUMBER AND DESCRIPTION OF THE PART(S) (see the EXPLODED DRAWING and PART LIST
on pages 28 to 31 of this manual)
LIMITED WARRANTY
ICON Health & Fitness, Inc. (ICON), warrants this product to be free from defects in workmanship and
material, under normal use and service conditions. The drive motor is warranted for three (3) years after
the date of purchase. The parts and labor are warranted for ninety (90) days after the date of purchase.
This warranty extends only to the original purchaser. ICON's obligation under this warranty is limited to
replacing or repairing, at ICON's option, the product through one of its authorized service centers. All re-
pairs for which warranty claims are made must be preauthorized by ICON. This warranty does not ex-
tend to any product or damage to a product caused by or attributable to freight damage, abuse, misuse,
improper or abnormal usage or repairs not provided by an ICON authorized service center; products
used for commercial or rental purposes; or products used as store display models. No other warranty be-
yond that specifically set forth above is authorized by ICON.
ICON is not responsible or liable for indirect, special or consequential damages arising out of or in con-
nection with the use or performance of the product or damages with respect to any economic loss, loss
of property, loss of revenues or profits, loss of enjoyment or use, costs of removal or installation or other
consequential damages of whatsoever nature. Some states do not allow the exclusion or limitation of in-
cidental or consequential damages. Accordingly, the above limitation may not apply to you.
The warranty extended hereunder is in lieu of any and all other warranties and any implied warranties of
merchantability or fitness for a particular purpose is limited in its scope and duration to the terms set
forth herein. Some states do not allow limitations on how long an implied warranty lasts. Accordingly, the
above limitation may not apply to you.
This warranty gives you specific legal rights. You may also have other rights which vary from state to state.
ICON HEALTH & FITNESS, INC., 1500 S. 1000 W., LOGAN, UT 84321-9813
Part No. 216430 R1004B
Printed in USA © 2004 ICON IP, Inc.
Download from Www.Somanuals.com. All Manuals Search And Download.
|