Model No. PFST12020
USER'S MANUAL
Model
Number
Decal
QUESTIONS?
If you have questions, or if there
are missing parts, we will guar-
antee complete satisfaction
through direct assistance from
our factory.
TO AVOID DELAYS, PLEASE
CALL DIRECT TO OUR TOLL-
FREE CUSTOMER HOT LINE.
The trained technicians on our
customer hot line will provide
immediate assistance, free of
charge to you.
CUSTOMER HOT LINE:
1-800-999-3756
Mon.–Fri., 6 a.m.–6 p.m. MST
CAUTION
Read all precautions and instruc-
tions in this manual before using
this equipment. Keep this manual
for future reference.
Visit our website at
new products, prizes,
fitness tips, and much more!
Download from Www.Somanuals.com. All Manuals Search And Download.
BEFORE YOU BEGIN
Congratulations for selecting the new PROFORM®
PROSTEP 220 stepper. Stepping is one of the most
effective exercises for increasing cardiovascular fit-
ness, building endurance, and toning the body. The
PROSTEP 220 is designed to let you enjoy this
healthful exercise in the convenience of your home.
Department toll-free at 1-800-999-3756, Monday
through Friday, 6 a.m. until 6 p.m. Mountain Time
(excluding holidays). To help us assist you, mention the
product model number and serial number when calling.
The model number is PFST12020. The serial number
can be found on a decal attached to the stepper (see
the front cover of this manual for the location).
For your benefit, read this manual carefully before
you use the stepper. If you have questions after
reading this manual, call our Customer Service
Before reading further, please familiarize yourself with
the parts that are labeled in the drawing below.
FRONT
Handlebar
Console
Lock Pin
Resistance Collar
Resistance Cylinder
Pedal
REAR
RIGHT SIDE
3
Download from Www.Somanuals.com. All Manuals Search And Download.
ASSEMBLY
Place all parts of the stepper in a cleared area and remove the packing materials. Do not dispose of the packing
materials until assembly is completed. Note: Some small parts may have been pre-attached for shipping. If
a part is not in the parts bag, check to see if it has been pre-attached.
Assembly requires only the included tools.
1. Attach a Foot (21) to the Left Pivot Arm (7) with an M5
1
x 25mm Screw (34) and an M5 Washer (39).
8
Attach the other Foot (21) to the Right Pivot Arm (8) in
the same way.
21
21
39
34
7
2. Raise the Left and Right Legs (4, 5) and the Handlebar
(2) until they are in the position shown in the inset
drawing.
2
Refer to the inset drawing. Insert the Lock Pin (27) into
the bracket on the Handlebar (2) and the hole near the
upper end of the Leg (1). Insert the Spring Clip (28)
into the end of the Lock Pin. Do not use the stepper
without the Spring Clip inserted into the Lock Pin.
5
4
2
27
2
5
28
4
1
4
Download from Www.Somanuals.com. All Manuals Search And Download.
3. Attach the indicated end of a Resistance Cylinder (10)
to the upper bracket on the Right Leg (5) with an M8 x
38mm Bolt (30) and an M8 Nylon Locknut (35).
3
30
5
Attach the lower end of the Resistance Cylinder (10)
to the bracket on the right Pedal Leg (6) with an M8 x
38mm Bolt (30) and an M8 Nylon Locknut (35).
35
Attach the other Resistance Cylinder (not shown) to
the left side of the stepper in the same way.
10
30
6
35
4. Refer to the inset drawing. The Console (3) requires
one “AA” battery (not included); an alkaline battery is
recommended. To install a battery, turn the Console
over, remove the battery cover, and insert the battery
into the battery clip (not shown). Make sure that the
negative end of the battery (marked “—”) is touch-
ing the spring in the battery clip. Reattach the bat-
tery cover.
4
Battery
Cover
Battery
3
24
3
2
Plug the Reed Wire (24) into the back of the Console
(3). Slide the Console onto the metal tab on the
Handlebar (2).
5. Make sure that all parts are properly tightened before you use the stepper. After assembly is completed,
some extra parts may be left over. Place a mat under the stepper to protect the floor.
5
Download from Www.Somanuals.com. All Manuals Search And Download.
HOW TO OPERATE THE STEPPER
HOW TO EXERCISE ON THE STEPPER
HOW TO USE THE CONSOLE
Place the stepper on a level surface and place a mat
under the stepper. Note: The stepper features preci-
sion hydraulic cylinders. Due to the nature of
hydraulic cylinders, there is a possibility of slight oil
leakage.
Hold the handlebars and step onto the pedals. Begin
stepping, alternately depressing the right and left ped-
als with a smooth, continuous motion. Because the
pedals move independently of each other, you must
maintain a continuous motion or both pedals will sink
to the floor. Change the height of your step or your
stepping pace until you can comfortably maintain a
continuous motion.
As you step, you can exercise your upper leg muscles
by keeping your feet flat on the pedals. To focus on
your calf muscles, rise on your toes as you step.
Stand erect or lean forward slightly as you exercise.
Always keep your back straight in order to avoid
injury.
If there is a thin sheet of clear plastic on the console,
remove the plastic. To turn on the console, press the
MODE/RESET button or begin stepping.
As you step, the upper half of the display will show
the total number of steps you have completed. A
mode arrow will point to the letters “CNT.”
HOW TO ADJUST THE RESISTANCE
To change the stepping resistance, turn the resistance
collars on the upper ends of the resistance cylinders
(see the inset drawing). The arrows on the resistance
cylinders and the marks on the resistance collars
show which resistance level has been selected. Make
sure that both resistance cylinders are at the same
resistance setting.
The lower half of the display will show the elapsed
time, the approximate number of calories you have
burned, and your stepping speed, changing from one
mode to the next every few seconds. One mode
arrow will point to the word “SCAN,” and a second
mode arrow will point to the letters “TIME,” “CAL,” or
“STEP/MIN.”
To view one mode continuously in the lower half of
the display, press the MODE/RESET button until there
is a mode arrow pointing to the letters “TIME,” “CAL,”
or “STEP/MIN.” but no mode arrow pointing to the
word “SCAN.” To view all three modes again, press
the button until there is a mode arrow pointing to the
word “SCAN.”
Resistance
Collar
To reset the display, press the MODE/RESET button
for a few seconds.
If the pedals are not moved and the MODE/RESET
button is not pressed for a few seconds, the word
“STOP” will appear in the left side of the display. If the
pedals are not moved and the button is not pressed
for a few minutes, the console will turn off.
WARNING:
The resistance cylin-
ders become very hot during use. Touch only
the resistance collars when changing the
stepping resistance.
6
Download from Www.Somanuals.com. All Manuals Search And Download.
MAINTENANCE AND TROUBLESHOOTING
Inspect and properly tighten all parts of the stepper
regularly. To clean the stepper, use a damp cloth and
a small amount of mild detergent. Never use abra-
sives or solvents. Keep liquid away from the con-
sole, and keep the console out of direct sunlight.
6
CONSOLE TROUBLESHOOTING
1
If the console does not function properly, or if the dis-
play becomes faint, refer to assembly step 4 on page
5 and replace the battery.
If the console still does not function properly, locate
the Reed Switch (24) under the Frame (1) (see the
inset drawing). Hold down the left Pedal Leg (6) so
that the Magnet (26) is level with the Reed Switch.
Slide the Reed Switch forward or backward slightly,
and then exercise for a moment to see whether the
console functions properly. If necessary, readjust the
position of the Reed Switch.
6
26
24
1
7
Download from Www.Somanuals.com. All Manuals Search And Download.
CONDITIONING GUIDELINES
The following guidelines will help you to plan your
exercise program. Remember that proper nutrition
and adequate rest are essential for successful results.
ber in your training zone as you exercise. For maxi-
mum fat burning, adjust the intensity of your exercise
until your heart rate is near the middle number in your
training zone as you exercise.
Aerobic Exercise
WARNING:
Before beginning
this or any exercise program, consult your
physician. This is especially important for
persons over the age of 35 or persons with
pre-existing health problems.
If your goal is to strengthen your cardiovascular sys-
tem, your exercise must be “aerobic.” Aerobic exer-
cise is activity that requires large amounts of oxygen
for prolonged periods of time. This increases the
demand on the heart to pump blood to the muscles,
and on the lungs to oxygenate the blood. For aerobic
exercise, adjust the intensity of your exercise until
your heart rate is near the highest number in your
training zone.
EXERCISE INTENSITY
Whether your goal is to burn fat or to strengthen your
cardiovascular system, the key to achieving the
desired results is to exercise with the proper intensity.
The proper intensity level can be found by using your
heart rate as a guide. The chart below shows recom-
mended heart rates for fat burning, maximum fat
burning, and cardiovascular (aerobic) exercise.
HOW TO MEASURE YOUR HEART RATE
To measure your
heart rate, first
exercise for at least
four minutes. Then,
stop exercising and
place two fingers
on your wrist as
shown. Take a six-
second heartbeat
count, and multiply the result by 10 to find your heart
rate. For example, if your six-second heartbeat count
is 14, your heart rate is 140 beats per minute. (A six-
second count is used because your heart rate will
drop rapidly when you stop exercising.)
To find the proper heart rate for you, first find your age
at the bottom line of the chart (ages are rounded off to
the nearest ten years). Next, find the three numbers
above your age. The three numbers are your “training
zone.” The lowest number is the recommended heart
rate for fat burning; the middle number is the recom-
mended heart rate for maximum fat burning; the high-
est number is the recommended heart rate for aerobic
exercise.
WORKOUT GUIDELINES
Each workout should include the following three parts:
A warm-up, consisting of 5 to 10 minutes of stretching
and light exercise. A proper warm-up increases your
body temperature, heart rate, and circulation in prepa-
ration for exercise.
Fat Burning
Training zone exercise, consisting of 20 to 30 min-
utes of exercising with your heart rate in your training
zone. Note: During the first few weeks of your exer-
cise program, do not keep your heart rate in your
training zone for longer than 20 minutes.
To burn fat effectively, you must exercise at a relative-
ly low intensity level for a sustained period of time.
During the first few minutes of exercise, your body
uses easily accessible carbohydrate calories for ener-
gy. Only after the first few minutes of exercise does
your body begin to use stored fat calories for energy.
If your goal is to burn fat, adjust the intensity of your
exercise until your heart rate is near the lowest num-
A cool-down, with 5 to 10 minutes of stretching. This
will increase the flexibility of your muscles and will
help to prevent post-exercise problems.
8
Download from Www.Somanuals.com. All Manuals Search And Download.
EXERCISE FREQUENCY
workouts. After a few months of regular exercise, you
may complete up to five workouts each week, if
desired. Remember, the key to success is make exer-
cise a regular and enjoyable part of your everyday life.
To maintain or improve your condition, plan three work-
outs each week, with at least one day of rest between
SUGGESTED STRETCHES
1
The correct form for several basic stretches is shown at the right.
Move slowly as you stretch—never bounce.
1. Toe Touch Stretch
Stand with your knees bent slightly and slowly bend forward from
your hips. Allow your back and shoulders to relax as you reach
down toward your toes as far as possible. Hold for 15 counts,
then relax. Repeat 3 times. Stretches: Hamstrings, back of knees
and back.
2
2. Hamstring Stretch
Sit with one leg extended. Bring the sole of the opposite foot
toward you and rest it against the inner thigh of your extended
leg. Reach toward your toes as far as possible. Hold for 15
counts, then relax. Repeat 3 times for each leg. Stretches:
Hamstrings, lower back and groin.
3
3. Calf/Achilles Stretch
With one leg in front of the other, reach forward and place your
hands against a wall. Keep your back leg straight and your back
foot flat on the floor. Bend your front leg, lean forward and move
your hips toward the wall. Hold for 15 counts, then relax. Repeat
3 times for each leg. To cause further stretching of the achilles
tendons, bend your back leg as well. Stretches: Calves, achilles
tendons and ankles.
4
4. Quadriceps Stretch
With one hand against a wall for balance, reach back and grasp
one foot with your other hand. Bring your heel as close to your
buttocks as possible. Hold for 15 counts, then relax. Repeat 3
times for each leg. Stretches: Quadriceps and hip muscles.
5
5. Inner Thigh Stretch
Sit with the soles of your feet together and your knees outward.
Pull your feet toward your groin area as far as possible. Hold for
15 counts, then relax. Repeat 3 times. Stretches: Quadriceps and
hip muscles.
9
Download from Www.Somanuals.com. All Manuals Search And Download.
PART LIST—Model No. PFST12020
R1202A
Key No. Qty.
Description
Key No. Qty.
Description
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
1
1
1
1
1
2
1
1
1
2
1
2
2
4
2
2
4
2
10
2
2
2
2
Frame
Handlebar
Console
Left Leg
Right Leg
Pedal Leg
Left Pivot Arm
Right Pivot Arm
Leg Tube
Hydraulic Resistance Cylinder
Pedal Axle
Handlebar Endcap
Foam Grip
Leg Bushing
Pivot Bushing
Leg Endcap
Pivot Arm Endcap
Pedal
Pedal Bushing
Wheel
Foot
Axle Cap
Bumper
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
#
1
1
1
1
1
1
4
2
2
2
3
9
2
8
2
5
2
1
2
2
1
1
1
Reed Switch/Wire
Clamp
Magnet
Lock Pin
Spring Clip
M8 x 85mm Bolt
M8 x 38mm Bolt
M8 x 60mm Bolt
M6 x 31mm Bolt
M8 x 48mm Bolt
M5 x 25mm Screw
M8 Nylon Locknut
M6 Nylon Locknut
1/4” x 5/8” Screw
#8 x 19mm Screw
M5 Washer
M5 x 10mm Screw
Stop
Rubber Grommet
Push Nut
User’s Manual
Multipurpose Tool
Allen Wrench
#
#
Note: “#” indicates a non-illustrated part. Specifications are subject to change without notice. See the back cover
of this manual for information about ordering replacement parts.
10
Download from Www.Somanuals.com. All Manuals Search And Download.
EXPLODED DRAWING—Model No. PFST12020
R1202A
12
2
30
33
13
3
27
14
34
39
29
35
5
35
41
35
14
14
31
9
28
35
15
42
35
33
10
15
35
4
30
1
17
11
35
16
19
17
31
10
37
36
19
8
20
32
42
24
18
22
43
25
17
37
30
40
19
21
19
16
35
37
18
39
39
23
20
36
6
38
17
34
32
37
35
7
19
30
19
43
39
23
38
22
21
39
6
26
40
34
19
11
Download from Www.Somanuals.com. All Manuals Search And Download.
HOW TO ORDER REPLACEMENT PARTS
To order replacement parts, simply call our Customer Service Department toll-free at 1-800-999-3756, Monday
through Friday, 6 a.m. until 6 p.m. Mountain Time (excluding holidays). To help us assist you, please be
prepared to give the following information when calling:
• The MODEL NUMBER of the product (PFST12020)
• The NAME of the product (PROFORM® PROSTEP 220 stepper)
• The SERIAL NUMBER of the product (see the front cover of this manual)
• The KEY NUMBER and DESCRIPTION of the part(s) (see the PART LIST on page 10)
LIMITED WARRANTY
ICON Health & Fitness, Inc. (ICON), warrants this product to be free from defects in workmanship and
material, under normal use and service conditions, for a period of 90 days from the date of purchase. This
warranty extends only to the original purchaser. ICON's obligation under this warranty is limited to replac-
ing or repairing, at ICON's option, the product through one of its authorized service centers. All repairs for
which warranty claims are made must be pre-authorized by ICON. This warranty does not extend to any
product or damage to a product caused by or attributable to freight damage, abuse, misuse, improper or
abnormal usage, or repairs not provided by an ICON authorized service center; to products used for com-
mercial or rental purposes; or to products used as store display models. No other warranty beyond that
specifically set forth above is authorized by ICON.
ICON is not responsible or liable for indirect, special, or consequential damages arising out of or in con-
nection with the use or performance of the product or damages with respect to any economic loss, loss of
property, loss of revenues or profits, loss of enjoyment or use, costs of removal, installation or other con-
sequential damages of whatsoever nature. Some states do not allow the exclusion or limitation of inci-
dental or consequential damages. Accordingly, the above limitation may not apply to you.
The warranty extended hereunder is in lieu of any and all other warranties and any implied warranties of
merchantability or fitness for a particular purpose is limited in its scope and duration to the terms set forth
herein. Some states do not allow limitations on how long an implied warranty lasts. Accordingly, the above
limitation may not apply to you.
This warranty gives you specific legal rights. You may also have other rights which vary from state to state.
ICON HEALTH & FITNESS, INC., 1500 S. 1000 W., LOGAN, UT 84321-9813
Part No. 192310 R1202A
Printed in China © 2002 ICON Health & Fitness, Inc.
Download from Www.Somanuals.com. All Manuals Search And Download.
|