®
Model No. PFHK99902
Serial No.
USER'S MANUAL
Find the serial number in the location
shown below. Write the serial number
in the space above for reference.
Serial Number Decal
QUESTIONS?
As a manufacturer, we are com-
mitted to providing complete
customer satisfaction. If you
have questions, or if there are
missing parts, we will guarantee
complete satisfaction through di-
rect assistance from our factory.
TO AVOID UNNECESSARY DE-
LAYS, PLEASE CALL DIRECT TO
OUR TOLL-FREE CUSTOMER
HOT LINE. The trained techni-
cians on our Customer Hot Line
will provide immediate assis-
tance, free of charge to you.
CUSTOMER HOT LINE:
1-800-999-3756
Mon.–Fri., 6 a.m.–6 p.m. MST
Patent Pending
CAUTION
Read all precautions and instruc-
tions in this manual before using
this equipment. Save this man-
ual for future reference.
Visit our website at
new products, prizes,
fitness tips, and much more!
Download from Www.Somanuals.com. All Manuals Search And Download.
Important Precautions
WARNING:
To reduce the risk of burns, fire, electric shock, or injury to persons, read the
following important precautions and information before operating the incline trainer.
1. It is the responsibility of the owner to ensure
that all users of the trainer are adequately in-
formed of all warnings and precautions.
the same circuit. Do not use an extension cord.
13. Use only a single-outlet surge suppressor that
is UL 1449 listed as a transient voltage surge
suppressor (TVSS). The surge suppressor
must have a UL suppressed voltage rating of
400 volts or less and a minimum surge dissi-
pation of 450 joules. The surge suppressor
must be electrically rated for 120 volts AC and
15 amps. To purchase a surge suppressor, see
your local PROFORM dealer or call 1-800-999-
3756 and order part number 146148.
2. Use the trainer only as described in this manual.
3. The trainer is intended for in-home use only.
Do not use the trainer in any commercial,
rental, or institutional setting.
4. Place the trainer on a level surface, with at
least eight feet of clearance behind it. Do not
place the trainer on any surface that blocks air
openings. To protect the floor or carpet from
damage, cover the floor under the trainer.
14. Keep the power cord and the surge suppres-
sor away from heated surfaces.
5. Keep the trainer indoors, away from moisture
and dust. Do not put the trainer in a garage or
covered patio, or near water.
15. The roller guards must be 1/8 inch from the
rear roller (the location of the roller guards is
shown on page 5). Unplug the power cord
and adjust the roller guards, if necessary.
6. Do not operate the trainer where aerosol
products are used or where oxygen is being
administered.
16. Never move the walking belt while the power
is turned off. Do not operate the trainer if the
power cord or plug is damaged, or if the
trainer is not working properly. (See BEFORE
YOU BEGIN on page 5 if the trainer is not
working properly.)
7. Do not operate the trainer until it is properly
assembled. (See ASSEMBLY on page 6.) You
must be able to safely lift 45 pounds (20 kg) in
order to move the trainer.
17. Never start the trainer while you are standing
on the walking belt. Always hold the handrails
while using the trainer.
8. Keep children under the age of 12 and pets
away from the trainer at all times.
9. The trainer should not be used by persons
weighing more than 300 pounds.
18. The trainer is capable of high speeds. Adjust
the speed in small increments to avoid sud-
den jumps in speed.
10. Never allow more than one person on the
trainer at a time.
19. The heart rate monitor is not a medical de-
vice. Various factors, including the user's
movement, may affect the accuracy of heart
rate readings. The heart rate monitor is in-
tended only as an exercise aid in determining
heart rate trends in general.
11. Wear appropriate exercise clothing when
using the trainer. Do not wear loose clothing
that could become caught in the trainer.
Athletic support clothes are recommended for
both men and women. Always wear athletic
shoes. Never use the trainer with bare feet,
wearing only stockings, or in sandals.
20. Never leave the trainer unattended while it is
running. Remove the key, unplug the power
cord, and move the on/off switch to the off po-
sition when the trainer is not in use. (The loca-
tion of the on/off switch is shown on page 5.)
12. When connecting the power cord (see page 8),
plug the power cord into a surge suppressor
(not included) and plug the surge suppressor
into a grounded circuit capable of carrying 15
or more amps. No other appliance should be on
21. Do not change the grade of the trainer by
placing objects under the trainer.
3
Download from Www.Somanuals.com. All Manuals Search And Download.
22. Never insert or drop any object into any
opening.
25. Always remove iFIT.com CD’s and videocas-
settes from your CD player or VCR when they
are not in use.
23. When using iFIT.com CD’s and videocas-
settes, an electronic “chirping” sound will
alert you when the grade and/or speed of the
trainer is about to change. Always listen for
the “chirp” and be prepared for grade and/or
speed changes. In some instances, the grade
and/or speed may change before the personal
trainer describes the change.
26. Inspect and tighten all parts of the trainer reg-
ularly.
27.
DANGER:
Always unplug the power
cord immediately after use, before cleaning
the trainer, and before performing the mainte-
nance and adjustment procedures described
in this manual. Never remove the motor cover
unless instructed to do so by an authorized
service representative. Servicing other than
the procedures in this manual should be per-
formed by an authorized service representa-
tive only.
24. When using iFIT.com CD’s and videocassettes,
you can manually override the grade and
speed settings by pressing the grade and
speed buttons. However, when the next “chirp”
is heard, the grade and/or speed will change to
the next settings of the CD or video program.
WARNING:
Before beginning this or any exercise program, consult your physician. This
is especially important for persons over the age of 35 or persons with pre-existing health problems.
Read all instructions before using. ICON assumes no responsibility for personal injury or property
damage sustained by or through the use of this product.
SAVE THESE INSTRUCTIONS
The decal shown at the right has been
attached to each side of the incline trainer. If
either decal is missing or illegible, call our
Customer Service Department, toll-free, to
order a free replacement decal (see
ORDERING REPLACEMENT PARTS on the
back cover of this manual). Apply the decal
in the location shown.
Note: The decal is shown
at 55% of actual size.
4
Download from Www.Somanuals.com. All Manuals Search And Download.
Before You Begin
Thank you for selecting the revolutionary PROFORM®
TRAIL RUNNER incline trainer. The TRAIL RUNNER
combines state-of-the-art technology with innovate
design to provide you with a motivating and effective
form of exercise in the convenience of your home.
Monday through Friday, 6 a.m. until 6 p.m. Mountain
Time (excluding holidays). To help us assist you,
please note the product model number and serial num-
ber before calling. The product model number is
PFHK99902. The serial number can be found on a
decal attached to the incline trainer (see the front
cover of this manual for the location).
For your benefit, read this manual carefully before
using the TRAIL RUNNER. If you have questions
after reading this manual, please call our Customer
Service Department toll-free at 1-800-999-3756,
Before reading further, please familiarize yourself with
the parts that are labeled in the drawing below.
Book Holder
Key/Clip
Water Bottle Holder*
Console
Handrail
LEFT SIDE
RIGHT SIDE
Cushioned Walking
Platform
Walking Belt
Foot Rail
Roller
Guards
Circuit Breaker
Power Cord
BACK
On/Off Switch
Roller Adjustment Bolts
*No water bottle is included.
5
Download from Www.Somanuals.com. All Manuals Search And Download.
Assembly
Assembly requires two people. Set the incline trainer in a cleared area and remove all packing materials. Do
not dispose of the packing materials until assembly is completed. Assembly requires the included allen
wrench
and your own phillips screwdriver
.
Note: The underside of the incline trainer walking belt is coated with high-performance lubricant. During shipping,
a small amount of lubricant may be transferred to the top of the walking belt or the shipping carton. This is a nor-
mal condition and does not affect trainer performance. If there is lubricant on top of the walking belt, simply wipe
off the lubricant with a soft cloth and a mild, non-abrasive cleaner.
Refer to the drawings below to identify the parts used in assembly.
Handrail Bolt (25)–4
1” Upright Bolt (33)–4
Handrail Star
Washer (26)–4
Internal Star
Washer (32)–4
Long Upright Bolt (54)–4
Small Screw (6)–4
1. Set the Console (99) and the Handrail (27) on the floor.
1
Locate the Handrail Wire Harness (30) in the Handrail
(27). While a second person holds the Console (99), con-
nect the 8-pin wire of the Handrail Wire Harness to the
HD2 connector on the back of the Console. Next, connect
the 4-pin wire to the IFIT2 connector, and the 3-pin wire
to the HD1 connector shown.
HD1
IFIT2
HD2
30
99
27
2. Attach the Console (99) to the Handrail (27) with the four
Small Screws (6). Make sure that the Handrail Wire
Harness (not shown) is not pinched between the
Console and the Handrail.
6
2
99
6
27
6
6
Download from Www.Somanuals.com. All Manuals Search And Download.
3. Identify the right Upright (23), which has the Upright Wire
Harness (100) inside of it.
3
23
Have a second person hold the right Upright (23) near the
Base Wire Harness (41) on the right side of the Base
(101). Connect the Upright Wire Harness (100) to the
Base Wire Harness (41). Make sure that the two connec-
tors snap together. Pull the excess Upright Wire Harness
out of the top of the right Upright.
100
41
101
Slide the right Upright (23) onto the Base (101). Be care-
ful not to pinch the Wire Harnesses (41 and 100).
4. Finger tighten two Long Upright Bolts (54) into the right
Upright (23) and the Base (101) as shown. Next, finger
tighten two of the four 1” Upright Bolts (33) with two of the
four Internal Star Washers (32) into the right Upright. Do
not tighten the Bolts yet.
4
33
32
33
Attach the left Upright (not shown) in the same way.
(Note: There is not a wire harness in the left Upright.) Do
not tighten the Bolts yet.
23
101
23
54
5. Have a second person hold the Handrail (27) near the
Uprights (23). Refer to the inset drawing. Slide an O-ring
(117) onto each Upright (23). Connect the Handrail Wire
Harness (30) to the Upright Wire Harness (100). Make
sure that the two connectors snap together. Insert the
Wire Harnesses into the Handrail (27) and the right
Upright (23).
5
27
26
26
25
23
Slide the Handrail (27) onto the Uprights (23). Be care-
23
25
ful not to pinch the Wire Harnesses (30 and 100).
27
23
Finger tighten two Handrail Bolts (25) with Handrail Star
Washers (26) into each side of the Handrail (27). Note: If
the Handrail Bolts do not line up with the holes in the
Uprights (23), roll the O-rings (117) onto the thicker parts
of the Uprights. After the Handrail has been attached, roll
the O-rings over the joints where the Handrail and the
Uprights meet.
117
30
100
Tighten all of the bolts used in steps 4 and 5.
6. Make sure that all parts are tightened before you use the incline trainer. Keep the included allen wrench in
a secure place. The allen wrench is used to adjust the walking belt (see page 22). To protect the floor or car-
pet from damage, cover the floor beneath the trainer.
7
Download from Www.Somanuals.com. All Manuals Search And Download.
Operation and Adjustment
THE PERFORMANT LUBETM WALKING BELT
This product is for use on a nominal 120-volt circuit,
and has a grounding plug that looks like the plug illus-
trated in drawing 1 below. A temporary adapter that
looks like the adapter illustrated in drawing 2 may be
used to connect the surge suppressor to a 2-pole
receptacle as shown in drawing 2 if a properly
grounded outlet is not available.
Your incline trainer features a walking belt coated with
PERFORMANT LUBETM, a high-performance lubricant.
IMPORTANT: Never apply silicone spray or other
substances to the walking belt or the walking plat-
form. Such substances will deteriorate the walking
belt and cause excessive wear.
1
HOW TO PLUG IN THE POWER CORD
Grounded Outlet Box
Surge Suppressor
Grounding Pin
DANGER:
Improper connection
of the equipment-grounding conductor can
result in an increased risk of electric shock.
Check with a qualified electrician or service-
man if you are in doubt as to whether the
product is properly grounded. Do not modify
the plug provided with the product—if it will
not fit the outlet, have a proper outlet
Grounding Pin
Grounded Outlet
Grounding Plug
installed by a qualified electrician.
2
Grounded Outlet Box
Adapter
Your incline trainer, like any other type of sophisticated
electronic equipment, can be seriously damaged by
sudden voltage changes in your home’s power.
Voltage surges, spikes, and noise interference can re-
sult from weather conditions or from other appliances
being turned on or off. To decrease the possibility of
your trainer being damaged, always use a surge
suppressor with your trainer (see drawing 1 at the
right).
Surge Suppressor
Lug
Metal Screw
The temporary adapter should be used only until a
properly grounded outlet (drawing 1) can be installed
by a qualified electrician.
To purchase a surge suppressor, see your local
PROFORM dealer or call 1-800-999-3756 and order
part number 146148. Use only a single-outlet surge
suppressor that is UL 1449 listed as a transient voltage
surge suppressor (TVSS). The surge suppressor must
have a UL suppressed voltage rating of 400 volts or
less and a minimum surge dissipation of 450 joules.
The surge suppressor must be electrically rated for
120 volts AC and 15 amps.
The green-colored rigid ear, lug, or the like extending
from the adapter must be connected to a permanent
ground such as a properly grounded outlet box cover.
Whenever the adapter is used it must be held in place
by a metal screw. Some 2-pole receptacle outlet box
covers are not grounded. Contact a qualified elec-
trician to determine if the outlet box cover is
grounded before using an adapter.
This product must be grounded. If it should malfunc-
tion or break down, grounding provides a path of least
resistance for electric current to reduce the risk of elec-
tric shock. This product is equipped with a cord having
an equipment-grounding conductor and a grounding
plug. Plug the power cord into a surge suppressor,
and plug the surge suppressor into an appropriate
outlet that is properly installed and grounded in
accordance with all local codes and ordinances.
Important: The incline trainer is not compatible
with GFCI-equipped outlets.
8
Download from Www.Somanuals.com. All Manuals Search And Download.
Note: If there is a thin sheet
of clear plastic on the face
of the console, remove it.
Clip
Key
FEATURES OF THE CONSOLE
stereo, portable stereo, or computer and play special
iFIT.com CD programs (CD’s are available separately).
iFIT.com CD programs automatically control the grade
and speed of the trainer as a personal trainer walks you
through every step of your workout. High-energy music
provides added motivation. Each CD features two pro-
grams designed by certified personal trainers.
The revolutionary incline trainer combines state-of-the-
art technology with innovate design to provide you with
a motivating and effective form of exercise in the conve-
nience of your home.
When the manual mode of the console is selected, the
grade and speed of the trainer can be changed with a
touch of a button. As you exercise, the console will dis-
play continuous exercise feedback. You can even
track your heart rate using the optional heart rate mon-
itor (for information about the optional heart rate
monitor, see page 19).
In addition, you can connect the trainer to your VCR
and TV and play iFIT.com video programs (videocas-
settes are available separately). Video programs offer
the same benefits as iFIT.com CD programs, but add
the excitement of exercising with a class and an instruc-
tor— the hottest new trend at health clubs.
The console also offers twelve preset programs. Each
preset program automatically controls the grade and
speed of the trainer to simulate a hiking trail as it
guides you through an effective workout. Choose from
beginner, intermediate, and advanced programs.
With the trainer connected to your computer, you can
access audio programs and video programs directly
from the internet. And by adding an optional upgrade
module to the trainer, you can use virtually endless
complete details. To purchase iFIT.com CD’s or
videocassettes, call toll-free 1-800-735-0768. To
order the optional upgrade module, see page 19.
The console also features new iFIT.com interactive
technology. IFIT.com technology is like having a per-
sonal trainer right in your home. Using the included
audio cable, you can connect the trainer to your home
9
Download from Www.Somanuals.com. All Manuals Search And Download.
Plug in the power cord.
2
3
CAUTION:
Before operating the
console, read the following precautions.
See HOW TO PLUG IN THE POWER CORD on
page 8.
• Do not stand on the walking belt when turn-
ing on the power.
Move the on/off switch to the on position.
• Always wear the clip (see the drawing below)
while operating the trainer.
Locate the on/off switch
on the trainer near the
On
power cord. Move the
Position
• Adjust the speed in small increments to
avoid sudden jumps in speed.
on/off switch to the on
position.
• To reduce the possibility of electric shock,
keep the console dry. Avoid spilling liquids
on the console and place only a sealed water
bottle in the water bottle holder.
Insert the key fully into the console.
4
Stand on the foot rails of the trainer. Attach the
clip securely to the waistband of your clothing.
Next, insert the key into the console. After a mo-
ment, various displays and indicators on the con-
sole will light. Note: When the key is inserted, the
trainer may automatically calibrate itself by rising
to the highest grade and then returning to the low-
est grade. During this process, the console will
show two dashes (– –) and one flashing indicator.
GETTING STARTED
Attach the clip to the waistband of your
clothing.
1
Stand on the foot rails
of the incline trainer.
Find the clip attached
to the key and slide
the clip onto the
waistband of your
clothing. Next, insert
the key into the con-
To use the manual mode of the console, follow the
steps beginning on page 11. To use a preset pro-
gram, see page 12. To use an iFIT.com CD or video
program, see page 16. To use an iFIT.com program
directly from our internet site, see page 18.
Clip
Key
sole. Test the clip by carefully taking a few
steps backward until the key is pulled from the
console. If the key is not pulled from the con-
sole, adjust the position of the clip as needed.
Then, remove the key from the console.
10
Download from Www.Somanuals.com. All Manuals Search And Download.
1%. To change the grade quickly, press the Quick
Incline buttons. The grade range is 0% to 25%.
Note: After the buttons are pressed, it will take a
moment for the trainer to reach the selected grade
setting.
HOW TO USE THE MANUAL MODE
Insert the key fully into the console.
1
See GETTING STARTED on page 10.
Follow your progress with the console displays.
5
Select the manual mode.
2
The matrix—When the
manual mode or an
iFIT.com program is se-
lected, the matrix will dis-
play a triangle represent-
ing a mountain. When the
When the key is in-
serted, the manual
mode will automatically
be selected, as shown
by the Manual indicator.
walking belt is started, the triangle will disappear
except for one flashing indicator. As you exercise,
the indicators in the triangle will light one at a time
until the entire triangle is again lit. This cycle will
then repeat. Each time the entire triangle lights,
you have walked 1/4 mile.
If a preset program has
been selected, press the Select Program button
repeatedly until the Manual indicator lights.
Press the Start button or the Speed
start the walking belt.
L
button to
3
The Speed display—
This display shows the
speed of the walking
belt.
A moment after the button is pressed, the walking
belt will begin to move at 1 mile per hour. Hold the
handrails and begin walking.
As you exercise,
change the speed of
the walking belt as de-
sired by pressing the
Note: The console can
display speed and dis-
tance in either miles or
kilometers. To see which
unit of measurement is
selected, hold down the
Stop button while inserting the key into the console.
An “E” for English miles or an “M” for metric kilo-
meters will appear in the Speed display. Press the
Speed
L
and
L
buttons. Each time a
button is pressed, the speed setting will change
by 0.1 mph; if a button is held down, the speed
setting will change in increments of 0.5 mph. To
change the speed setting quickly, press the Quick
Speed buttons. The speed range is 0.5 mph to 6
mph. Note: After the buttons are pressed, it will take
a moment for the walking belt to reach the selected
speed setting.
Speed
L
button to change the unit of measure-
ment. When the desired unit of measurement is
selected, remove the key and then re-insert it.
Note: For simplicity, all instructions in this manual
refer to miles.
To stop the walking belt, press the Stop button.
The displays will pause and the Distance/Time
display will begin to flash. To restart the walking
The Vertical Feet/
Cals./Grade display—
This display shows the
belt, press the Start button or the Speed
L
button.
number of vertical feet
you have climbed, the
Change the grade of the trainer as desired.
4
grade of the trainer, and
To change the grade of
the trainer, press the
the approximate number of calories you have
burned. The display will change from one number
to the next every seven seconds, as shown by the
indicators around the display.
Incline
L
and
L
but-
tons. Each time a but-
ton is pressed, the
grade will change by
11
Download from Www.Somanuals.com. All Manuals Search And Download.
The Distance/Time
display—When the
HOW TO USE PRESET PROGRAMS
manual mode or an
The console offers twelve preset programs. Each preset
program automatically controls the grade and speed of
the trainer to simulate a hiking trail as it guides you
through an effective workout. You can choose from four
beginner programs, four intermediate programs, and
four advanced programs.
iFIT.com program is se-
lected, this display will
show the distance you
have hiked and the elapsed time. The distance will
be shown for seven seconds and the time will be
shown for fourteen seconds, as shown by the indi-
cators around the display.
Follow the steps below to use a preset program.
When a preset program is selected, the Distance/
Time display will show the distance you have hiked,
the time remaining in the program, and the time
remaining in the current segment of the program.
Insert the key fully into the console.
1
See GETTING STARTED on page 10.
Pulse display—This
display will show your
heart rate when the op-
tional heart rate moni-
tor is worn. (For infor-
Select the desired preset program.
2
When the key is inserted, the manual mode will be
selected. To select a preset program, press the
Select Program
mation about the op-
tional heart rate monitor, see page 19.)
button repeat-
edly. The
Trail Display
twelve trails
shown in the
trail display
represent the
twelve preset
programs. As
you press the
Select Program button repeatedly, indicators will
light in the trail display to show which trail you
have selected.
To reset the displays, press the Stop button, re-
move the key, and then re-insert the key.
When you are finished exercising, stop the
walking belt and remove the key.
6
Step onto the foot rails and press the Stop button.
Next, remove the key from the console and put it in
a secure place. Note: If the displays and indica-
tors on the console remain lit after the key is
removed, the console is in the “demo” mode.
Refer to page 19 and turn off the demo mode.
When a preset program is selected, the matrix will
show the grade settings for the program. (For the
When you are finished using the trainer, move the
on/off switch near the power cord to the off position
and unplug the power cord.
longest programs, the matrix will not show all of
the grade settings at once.) In addition, the Speed
display will show the maximum speed setting for
the program and the Vertical Feet/Cals./Grade
display will show the maximum grade setting for
the program.
12
Download from Www.Somanuals.com. All Manuals Search And Download.
If the grade or speed setting for the current
segment is too high or too low, you can manually
override the setting by pressing the Incline or
Speed buttons on the console. Every few times
one of the Incline buttons is pressed, an additional
indicator will light or darken in the Current Segment
column of the matrix. Important: If you manually
override the grade or speed setting for the cur-
rent segment, when the segment ends the
trainer will automatically adjust to the grade
and speed settings for the next segment. Note:
Because each program is based on a preset dis-
tance, if you manually increase the speed, the
time remaining in the current segment and the
time remaining in the program will decrease; if you
manually decrease the speed, the time remaining
in the current segment and the time remaining in
the program will increase.
Press the Start button or the Speed
start the program.
L
button to
3
A moment after the button is pressed, the trainer
will automatically adjust to the first grade and
speed settings for the program. Hold the handrails
and begin walking.
Each program is divided into several time seg-
ments of different lengths. The Distance/Time dis-
play shows both the time remaining in the program
and the time remaining in the current segment of
the program. One grade setting and one speed
setting are programmed for each segment. The
grade setting for
the first segment
Current Segment
is shown in the
flashing Current
Segment column
of the matrix.
To stop the program temporarily, press the Stop
button. The displays will pause and the Distance/
Time display will begin to flash. To restart the pro-
(The speed set-
tings are not
shown in the ma-
trix.) The grade
settings for upcoming segments are shown in the
columns to the right.
gram, press the Start button or the Speed
L
but-
ton. To end the program, press the Stop button, re-
move the key, and then re-insert the key. Pressing
the Program Select button will also end the pro-
gram and will select the next preset program.
When only three seconds remain in the first seg-
ment of the program, both the Current Segment
column and the column to the right will flash and a
series of tones will sound. In addition, the Speed
display will flash three times if the speed is about
to change, and the Vertical Feet/Cals./Grade dis-
play will flash if the grade is about to change.
When the first segment is completed, all grade set-
tings in the matrix will move one column to the left.
The grade setting for the second segment will
then be shown in the flashing Current Segment
column and the trainer will automatically adjust to
the grade and speed settings for the second seg-
ment.
Follow your progress with the displays.
4
5
See step 5 on page 11.
When the program is completed, remove the
key.
Step onto the foot rails and remove the key from
the console. Make sure to keep the key in a secure
place. Note: If the displays and indicators on
the console remain lit after the key is removed,
the console is in the “demo” mode. Refer to
page 19 and turn off the demo mode.
When you are finished using the trainer, move the
on/off switch near the power cord to the off position
and unplug the power cord.
The program will continue until the grade setting
for the last segment is shown in the Current
Segment column of the matrix and no time re-
mains in the program. The walking belt will then
slow to a stop.
13
Download from Www.Somanuals.com. All Manuals Search And Download.
HOW TO CONNECT YOUR PORTABLE STEREO
HOW TO CONNECT THE INCLINE TRAINER TO
YOUR CD PLAYER, VCR, OR COMPUTER
Note: If your stereo has an RCA-type AUDIO OUT
jack, see instruction A below. If your stereo has a
3.5mm LINE OUT jack, see instruction B. If your
stereo has only a PHONES jack, see instruction C.
To use iFIT.com CD’s, the trainer must be connected
to your portable CD player, portable stereo, home
stereo, or computer with CD player. See this page and
page 15 for connecting instructions. To use iFIT.com
videocassettes, the trainer must be connected to your
VCR. See page 16 for connecting instructions. To use
iFIT.com programs directly from our internet site,
the trainer must be connected to your home computer.
See page 15 for connecting instructions.
A. Plug one end of the audio cable into the jack on the
side of the trainer near the power cord. Plug the
other end of the cable into the included adapter. Plug
the adapter into an AUDIO OUT jack on your stereo.
A
HOW TO CONNECT YOUR PORTABLE CD PLAYER
AUDIO OUT
RIGHT
LEFT
Note: If your CD player has separate LINE OUT and
PHONES jacks, see instruction A below. If your CD
player has only one jack, see instruction B.
Audio
Cable
Adapter
A. Plug one end of the audio cable into the jack on the
side of the trainer near the power cord. Plug the
other end of the cable into the LINE OUT jack on
your CD player. Plug your headphones into the
PHONES jack.
B. Plug one end of the audio cable into the jack on the
side of the trainer near the power cord. Plug the
other end of the cable into the LINE OUT jack on
your stereo.
A
PHONES LINE OUT
LINE OUT
PHONES
B
LINE OUT
Head-
phones
Audio
Cable
Audio
Cable
B. Plug one end of the audio cable into the jack on the
side of the trainer near the power cord. Plug the
other end of the cable into a 3.5mm Y-adapter
(available at electronics stores). Plug the Y-adapter
into the PHONES jack on your CD player. Plug your
headphones into the other side of the Y-adapter.
C. Plug one end of the audio cable into the jack on the
side of the trainer near the power cord. Plug the
other end of the cable into a 3.5mm Y-adapter
(available at electronics stores). Plug the Y-adapter
into the PHONES jack on your stereo. Plug your
headphones into the other side of the Y-adapter.
B
PHONES
C
PHONES
3.5mm
Y-adapter
PHONES
Audio
Cable
3.5mm
Y-adapter
Audio
Cable
Headphones
Headphones
14
Download from Www.Somanuals.com. All Manuals Search And Download.
HOW TO CONNECT YOUR HOME STEREO
HOW TO CONNECT YOUR COMPUTER
Note: If your stereo has an unused LINE OUT jack,
see instruction A below. If the LINE OUT jack is
being used, see instruction B.
Note: If your computer has a 3.5mm LINE OUT jack,
see instruction A. If your computer has only a
PHONES jack, see instruction B.
A. Plug one end of the audio cable into the jack on the
side of the trainer near the power cord. Plug the other
end of the cable into the included adapter. Plug the
adapter into the LINE OUT jack on your stereo.
A. Plug one end of the audio cable into the jack on the
side of the trainer near the power cord. Plug the
other end of the cable into the LINE OUT jack on
your computer.
A
A
CD
VCR
LINE OUT
Amp
LINE OUT
LINE OUT
Audio
Cable
Audio
Cable
Adapter
B. Plug one end of the audio cable into the jack on the
side of the trainer near the power cord. Plug the
other end of the cable into a 3.5mm Y-adapter
(available at electronics stores). Plug the Y-adapter
into the PHONES jack on your computer. Plug your
headphones or speakers into the other side of the
Y-adapter.
B. Plug one end of the audio cable into the jack on the
side of the trainer near the power cord. Plug the
other end of the cable into the included adapter.
Plug the adapter into an RCA Y-adapter (available
at electronics stores). Next, remove the wire that is
currently plugged into the LINE OUT jack on your
stereo and plug the wire into the unused side of the
RCA Y-adapter. Plug the RCA Y-adapter into the
LINE OUT jack on your stereo.
B
PHONES
B
CD
Audio
Cable
3.5mm
Y-adapter
VCR
Amp
LINE OUT
Headphones/Speakers
RCA
Y-adapter
Audio
Adapter
Cable
Wire removed from
LINE OUT jack
15
Download from Www.Somanuals.com. All Manuals Search And Download.
HOW TO CONNECT YOUR VCR
HOW TO USE IFIT.COM CD AND VIDEO
PROGRAMS
Note: If your VCR has an unused AUDIO OUT jack,
see instruction A below. If the AUDIO OUT jack is
being used, see instruction B. If you have a TV
with a built-in VCR, see instruction B. If your VCR
is connected to your home stereo, see HOW TO
CONNECT YOUR HOME STEREO on page 15.
To use iFIT.com CD’s or videocassettes, the trainer
must be connected to your portable CD player, portable
stereo, home stereo, computer with CD player, or VCR.
See HOW TO CONNECT THE INCLINE TRAINER TO
YOUR CD PLAYER, VCR, OR COMPUTER on page
14. Note: To purchase iFIT.com CD’s or videocas-
settes, call toll-free 1-800-735-0768.
A. Plug one end of the audio cable into the jack on the
side of the trainer near the power cord. Plug the other
end of the cable into the included adapter. Plug the
adapter into the AUDIO OUT jack on your VCR.
Follow the steps below to use an iFIT.com CD or video
program.
A
ANT. IN
VIDEO AUDIO
IN
RF OUT
Insert the key fully into the console.
CH
3
4
OUT
1
AUDIO OUT
See GETTING STARTED on page 10.
RIGHT
LEFT
Select the iFIT.com mode.
2
Audio
Cable
Adapter
When the key is in-
serted, the manual
mode will be selected.
To use an iFIT.com CD
or video program, press
the iFIT.com button. The
indicator on the button will light.
B. Plug one end of the audio cable into the jack on the
side of the trainer near the power cord. Plug the
other end of the cable into the included adapter.
Plug the adapter into an RCA adapter (available at
electronics stores). Next, remove the wire that is
currently plugged into the AUDIO OUT jack on your
VCR and plug the wire into the unused side of the
RCA adapter. Plug the RCA adapter into the AUDIO
OUT jack on your VCR.
Insert the iFIT.com CD or videocassette.
3
If you are using an iFIT.com CD, insert the CD
into your CD player. If you are using an iFIT.com
videocassette, insert the videocassette into your
VCR.
Press the PLAY button on your CD player or
VCR.
B
4
ANT IN
.
VIDEO AUDIO
IN
RF OUT
CH
3
4
OUT
A moment after the button is pressed, your per-
sonal trainer will begin guiding you through the
program. Simply follow your personal trainer’s
instructions. Note: If the Distance/Time display is
RCA Adapter
Adapter
Audio
Cable
flashing, press the Start button or the Speed
L
button on the console. The trainer will not respond
to a CD or video program when the display is
flashing.
Wire removed from
AUDIO OUT jack
During the CD or video program, an electronic
“chirping” sound will alert you when the grade
and/or speed of the trainer is about to change.
CAUTION: Always listen for the “chirp” and be
prepared for grade and/or speed changes. In
some instances, the grade and/or speed may
change before the personal trainer describes
the change.
16
Download from Www.Somanuals.com. All Manuals Search And Download.
If the grade or speed settings are too high or too
low, you can manually override the settings at any
time by pressing the Incline or Speed buttons on
the console. However, when the next “chirp” is
heard, the speed and/or grade will change to
the next settings of the CD or video program.
play is not flashing. If the display is flashing,
press the Start button or the Speed
L
button
on the console.
• Adjust the volume of your CD player or VCR.
If the volume is too high or too low, the con-
sole may not detect the program signals.
To stop the walking belt at any time, press the
Stop button on the console. The Distance/Time
display will begin to flash. To restart the program,
• Make sure that the audio cable is properly
connected, that it is fully plugged in, and that
it is not wrapped around a power cord.
press the Start button or the Speed
L
button.
After a moment, the walking belt will begin to
move at 1 mph. When the next “chirp” is heard,
the grade and speed will change to the next
settings of the CD or video program. Pressing
the Stop button on your CD player or VCR will
also stop the program.
• If you are using your portable CD player and
the CD skips, set the CD player on the floor or
another flat surface instead of on the console.
Follow your progress with the displays.
5
6
See step 5 on page 11.
When the CD or video program is completed, the
walking belt will stop and the Distance/Time display
will begin to flash. Note: To use another CD or
video program, press the Stop button or remove
the key and go to step 1 on page 19.
When the program is completed, remove the
key.
See step 6 on page 12.
Note: If the grade or speed of the trainer does
not change when a “chirp” is heard:
• Make sure that the indicator on the iFIT.com
button is lit and that the Distance/Time dis-
17
Download from Www.Somanuals.com. All Manuals Search And Download.
Return to the trainer and stand on the foot rails.
Find the clip attached to the key and slide the
clip onto the waistband of your clothing.
HOW TO USE PROGRAMS DIRECTLY FROM
OUR INTERNET SITE
7
When the on-screen countdown ends, the program
will begin and the walking belt will begin to move.
Hold the handrails, step onto the walking belt, and
begin walking. During the program, an electronic
“chirping” sound will alert you when the grade
and/or speed of the trainer is about to change.
CAUTION: Always listen for the “chirp” and be
prepared for grade and/or speed changes.
access a selection of programs that interactively con-
trol your incline trainer to help you achieve your spe-
cific exercise goals. In addition, you can play iFIT.com
audio and video programs directly from the internet. By
adding an optional upgrade module to the console, you
can use virtually endless features from our internet site.
Explore www.iFIT.com for details. To purchase an up-
grade module, see page 19.
If the grade or speed settings are too high or too
low, you can manually override the settings at any
time by pressing the Incline or Speed buttons on
the console. However, when the next “chirp” is
heard, the grade and/or speed will change to
the next settings of the program.
To use programs from our internet site, the trainer
must be connected to your home computer. See HOW
TO CONNECT YOUR COMPUTER on page 15. In
addition, you must have an internet connection and
an internet service provider. A list of specific system
requirements will be found on our internet site.
To stop the walking belt at any time, press the
Stop button on the console. The Distance/Time
display will begin to flash. To restart the program,
Follow the steps below to use a program from our
internet site.
press the Start button or the Speed
L
button.
After a moment, the walking belt will begin to
move at 1 mph. When the next “chirp” is heard,
the grade and speed will change to the next
settings of the program.
Insert the key fully into the console.
1
See GETTING STARTED on page 10.
Select the iFIT.com mode.
When the program is completed, the walking belt
will stop and the Distance/Time display will begin
to flash. Note: To use another program, press the
Stop button and go to step 5.
2
When the key is inserted, the manual mode will be
selected. To use a program from our internet site,
press the iFIT.com button. The indicator on the but-
ton will light.
Note: If the grade or speed of the trainer does
not change when a “chirp” is heard, make sure
that the indicator on the iFIT.com button is lit
and that the Distance/Time display is not flash-
ing. In addition, make sure that the audio cable
is properly connected, that it is fully plugged in,
and that it is not wrapped around a power cord.
Go to your computer and start an internet
connection.
3
Start your web browser, if necessary, and go to
4
Follow the links on our internet site to select a
program.
Follow your progress with the displays.
5
8
9
See step 5 on page 11.
Read and follow the on-line instructions for using a
program.
When the program is completed, remove the
key.
Follow the on-line instructions to start the
program.
6
See step 6 on page 12.
When you start the program, an on-screen count-
down will begin.
18
Download from Www.Somanuals.com. All Manuals Search And Download.
THE INFORMATION MODE/DEMO MODE
THE OPTIONAL IFIT.COM MODULE
The console features an information mode that keeps
track of the total number of hours that the incline
trainer has been operated and the total number of
miles that the walking belt has moved. The information
mode also allows you to switch the console from miles
to kilometers. In addition, the information mode allows
you to turn on and turn off the demo mode.
By adding an optional
iFIT.com module to the
incline trainer, you can
use virtually endless fea-
tures from our internet
site. Imagine on-line com-
petitions, personal train-
ing sessions via the inter-
To select the information mode, hold down the Stop
button while inserting the key into the console. When
the information mode is selected, the console will show
the following information:
net, and the ability to use your computer to track your
programs. For information about purchasing the op-
tional iFIT.com module, call toll-free 1-800-735-
0768.
THE OPTIONAL HEART RATE MONITOR
An “E” for English miles or
an “M” for metric kilometers
will appear in the Speed dis-
An optional heart rate monitor adds even more
features to the console. The heart rate monitor provides
hands-free operation and continuously monitors your
heart rate during your workouts. To purchase the
optional heart rate monitor, call toll-free 1-800-999-
3756.
play. Press the Speed
L
button to change the unit of
measurement.
The Vertical Feet/Cals./
Grade display will show the
total number of miles that
the walking belt has moved.
The Distance/Time display
will show the total number of
hours that the trainer has
been used.
IMPORTANT: Make sure
that there is not a letter
“d” in the Pulse display. If
a “d” appears in the display,
the console is in the “demo”
mode. This mode is intended
to be used only when a trainer is displayed in a store.
When the console is in the demo mode, the power cord
can be plugged in, the key can be removed from the
console, and the displays and indicators on the console
will automatically light in a preset sequence, although
the buttons on the console will not operate. If a “d” ap-
pears in the Pulse display when the information
mode is selected, press the Speed
L
button so the
display is blank.
To exit the information mode, remove the key from the
console.
19
Download from Www.Somanuals.com. All Manuals Search And Download.
How to Move the Incline Trainer
Before moving the incline trainer, change the grade of the incline trainer to the lowest level and unplug
the power cord.
1. Hold the handrails as shown and place one foot against
the walking belt.
2. Tilt the incline trainer back until it rolls freely on the wheels.
The help of a second person may be helpful when tipping
the trainer. Carefully move the trainer to the desired loca-
tion. Never move the trainer without tipping it back. To
reduce the risk of injury, use extreme caution while
moving the trainer. Do not attempt to move the trainer
over an uneven surface.
3. Place one foot on the walking belt, and carefully lower the
incline trainer until it is resting on the floor.
Wheels
Trouble-shooting
Most problems can be solved by following the steps below. Find the symptom that applies, and follow the
steps listed. If further assistance is needed, call our Customer Service Department toll-free at 1-800-999-
3756, Monday through Friday, 6 a.m. until 6 p.m. Mountain Time (excluding holidays).
PROBLEM: The power does not turn on
SOLUTION: a. Make sure that the power cord is plugged into a surge suppressor, and that the surge suppressor
is plugged into a properly grounded outlet (see page 8). Use only a single-outlet surge suppres-
sor that is UL 1449 listed as a transient voltage surge suppressor (TVSS). The surge suppressor
must have a UL suppressed voltage rating of 400 volts or less and a minimum surge dissipation
of 450 joules. The surge suppressor must be electrically rated for 120 volts AC and 15 amps.
Important: The incline trainer is not compatible with GFCI-equipped outlets.
b. After the power cord has been plugged in, make sure that the key is fully inserted into the console.
c. Check the circuit breaker located on the incline
c
trainer near the power cord. If the switch protrudes as
shown, the circuit breaker has tripped. To reset the
circuit breaker, wait for five minutes and then press
the switch back in.
Reset
Tripped
d
d. Check the on/off switch located on the incline trainer
near the power cord. The switch must be in the on
position.
On
Position
20
Download from Www.Somanuals.com. All Manuals Search And Download.
PROBLEM: The power turns off during use
SOLUTION: a. Check the circuit breaker located on the trainer near the power cord (see c. on page 20). If the
circuit breaker has tripped, wait for five minutes and then press the switch back in.
b. Make sure that the power cord is plugged in.
c. Remove the key from the console. Re-insert the key fully into the console.
d. Make sure that the on/off switch is in the “on” position.
e. If the incline trainer still will not run, please call our Customer Service Department, toll-free.
PROBLEM: The key is inserted and the displays on the console are lit, but the walking belt will not start
SOLUTION: a. Unplug the power cord, wait for five minutes, and then plug the power cord back in.
PROBLEM: The displays of the console do not function properly
SOLUTION: a. Remove the key from the console and UNPLUG THE
a
43
POWER CORD. Remove the two indicated Screws
(43) from the Belly Pan (16). Loosen the other indi-
cated Screw three turns. Carefully lift off the Front
Roller Cover.
Loosen
three
turns
16
43
b. Locate the Reed Switch (87) and the Magnet (13) on
the side of the Pulley (11). Turn the Pulley until the
Magnet is aligned with the Reed Switch. Make sure
that the gap between the Magnet and the Reed
Switch is about 1/8”. If necessary, loosen the Screw
(43) and move the Reed Switch slightly. Retighten the
Screw. Re-attach the front roller cover, and run the
trainer for a few minutes to check for a correct speed
reading.
b
1/8”
87
43
13
Top
View
11
PROBLEM: The grade of the incline trainer does not change correctly or does not change when iFIT.com
CD’s and videocassettes are played
SOLUTION: a. With the key in the console, press one of the Incline buttons. While the grade is changing, re-
move the key. After a few seconds, re-insert the key. The incline trainer will automatically rise to
the highest grade and then return to the lowest grade. This will recalibrate the trainer.
b. If an “E6” appears in the Distance/Time display, remove the key and unplug the power cord. Wait
for sixty seconds, plug in the power cord, and re-insert the key.
21
Download from Www.Somanuals.com. All Manuals Search And Download.
PROBLEM: The walking belt slows when walked on
SOLUTION: a. Use only a single-outlet surge suppressor that is UL 1449 listed as a transient voltage surge sup-
pressor (TVSS). The surge suppressor must have a UL suppressed voltage rating of 400 volts or
less and a minimum surge dissipation of 450 joules. The surge suppressor must be electrically
rated for 120 volts AC and 15 amps.
b. If the walking belt is overtightened, incline trainer per-
b
formance may decrease and the walking belt may be-
2”–3”
come damaged. Remove the key and UNPLUG THE
POWER CORD. Using the allen wrench, turn both
rear roller adjustment bolts counterclockwise, 1/4 of a
turn. When the walking belt is correctly tightened, you
should be able to lift each side of the walking belt 2 to
3 inches off the walking platform. Be careful to keep
the walking belt centered. Plug in the power cord, in-
sert the key and carefully walk on the incline trainer
for a few minutes. Repeat until the walking belt is
properly tightened.
Rear Roller
Adjustment Bolts
c. If the walking belt still slows, please call our Customer Service Department, toll-free.
PROBLEM: The walking belt is off-center
SOLUTION: a. If the walking belt has shifted to the left, first remove
the key and UNPLUG THE POWER CORD. Using the
allen wrench, turn the left rear roller adjustment bolt clock-
wise, and the right bolt counterclockwise, 1/4 of a turn
each. Be careful not to overtighten the walking belt. Plug
in the power cord, insert the key and run the incline
trainer for a few minutes. Repeat until the walking belt is
centered.
a
b. If the walking belt has shifted to the right, first remove
the key and UNPLUG THE POWER CORD. Using the
allen wrench, turn the left rear roller adjustment bolt coun-
terclockwise, and the right bolt clockwise, 1/4 of a turn
each. Be careful not to overtighten the walking belt. Plug
in the power cord, insert the key and run the incline
trainer for a few minutes. Repeat until the walking belt is
centered.
b
PROBLEM: The walking belt slips when walked on
SOLUTION: a. If the walking belt slips when walked on, first remove the
key and UNPLUG THE POWER CORD. Using the allen
wrench, turn both rear roller adjustment bolts clockwise,
1/4 of a turn. When the walking belt is correctly tightened,
you should be able to lift each side of the walking belt 3 to
4 inches off the walking platform. Be careful to keep the
walking belt centered. Plug in the power cord, insert the
key and carefully walk on the incline trainer for a few min-
utes. Repeat until the walking belt is properly tightened.
a
22
Download from Www.Somanuals.com. All Manuals Search And Download.
Conditioning Guidelines
Aerobic Exercise
WARNING:
Before beginning this
If your goal is to strengthen your cardiovascular sys-
tem, your exercise must be “aerobic.” Aerobic exercise
is activity that requires large amounts of oxygen for
prolonged periods of time. This increases the demand
on the heart to pump blood to the muscles, and on the
lungs to oxygenate the blood. For aerobic exercise,
adjust the grade and speed of the incline trainer until
your heart rate is near the highest number in your
training zone.
or any exercise program, consult your physi-
cian. This is especially important for individu-
als over the age of 35 or individuals with pre-
existing health problems.
The following guidelines will help you to plan your ex-
ercise program. For more detailed exercise informa-
tion, obtain a reputable book or consult your physician.
HOW TO MEASURE YOUR HEART RATE
EXERCISE INTENSITY
To measure your
heart rate, stop exer-
cising and place two
fingers on your wrist
as shown. Take a six-
second heartbeat
count, and multiply
Whether your goal is to burn fat or to strengthen your
cardiovascular system, the key to achieving the
desired results is to exercise with the proper intensity.
The proper intensity level can be found by using your
heart rate as a guide. The chart below shows recom-
mended heart rates for fat burning and aerobic exercise.
the result by ten to
To find the proper heart rate for you, first find your age
near the bottom of the chart (ages are rounded off to
the nearest ten years). Next, find the three numbers
above your age. The three numbers define your “train-
ing zone.” The lower two numbers are recommended
heart rates for fat burning; the higher number is the
recommended heart rate for aerobic exercise.
find your heart rate. (A six-second count is used be-
cause your heart rate drops quickly when you stop ex-
ercising.)
PROGRAM GUIDELINES
Each program should include the following three parts:
A Warm-up—Start each program with 5 to 10 minutes
of stretching and light exercise. A proper warm-up in-
creases your body temperature, heart rate and circula-
tion in preparation for exercise.
Training Zone Exercise—After warming up, increase
the intensity of your exercise until your heart rate is in
your training zone for 20 to 60 minutes. (During the
first few weeks of your exercise program, do not keep
your heart rate in your training zone for longer than 20
minutes.) Breathe regularly and deeply as you exercise.
Fat Burning
To burn fat effectively, you must exercise at a relatively
low intensity level for a sustained period of time.
During the first few minutes of exercise, your body
uses easily accessible carbohydrate calories for en-
ergy. Only after the first few minutes does your body
begin to use stored fat calories for energy. If your goal
is to burn fat, adjust the grade and speed of the incline
trainer until your heart rate is near the lowest number
in your training zone.
A Cool-down—Finish each program with 5 to 10 min-
utes of stretching to cool down. This will increase the
flexibility of your muscles and will help prevent post-ex-
ercise problems.
EXERCISE FREQUENCY
To maintain or improve your condition, complete three
programs each week, with at least one day of rest be-
tween programs. After a few months, you may com-
plete up to five programs each week if desired. The
key to success is to make exercise a regular and en-
joyable part of your everyday life.
For maximum fat burning, adjust the grade and speed
of the incline trainer until your heart rate is near the
middle number in your training zone.
23
Download from Www.Somanuals.com. All Manuals Search And Download.
Ordering Replacement Parts
To order replacement parts, call our Customer Service Department toll-free at 1-800-999-3756, Monday through
Friday, 6 a.m. until 6 p.m. Mountain Time (excluding holidays). When ordering parts, please be prepared to give
the following information:
• The MODEL NUMBER OF THE PRODUCT (PFHK99902)
• The NAME OF THE PRODUCT (PROFORM® TRAIL RUNNER incline trainer)
• The SERIAL NUMBER OF THE PRODUCT (see the front cover of this manual)
• The KEY NUMBER AND DESCRIPTION OF THE PART(S) (see the PART LIST and the EXPLODED DRAWING
attached in the center of this manual).
If possible, place the incline trainer near your telephone for easy reference when calling.
Limited Warranty
ICON Health & Fitness, Inc. (ICON), warrants this product to be free from defects in workmanship and
material, under normal use and service conditions, for a period of ninety (90) days from the date of pur-
chase. This warranty extends only to the original purchaser. ICON's obligation under this warranty is lim-
ited to replacing or repairing, at ICON's option, the product at one of its authorized service centers. All
products for which warranty claim is made must be received by ICON at one of its authorized service
centers with all freight and other transportation charges prepaid, accompanied by sufficient proof of pur-
chase. All returns must be pre-authorized by ICON. This warranty does not extend to any product or
damage to a product caused by or attributable to freight damage, abuse, misuse, improper or abnormal
usage or repairs not provided by an ICON authorized service center, to products used for commercial or
rental purposes, or to products used as store display models. No other warranty beyond that specifically
set forth above is authorized by ICON.
ICON is not responsible or liable for indirect, special or consequential damages arising out of or in con-
nection with the use or performance of the product or damages with respect to any economic loss, loss
of property, loss of revenues or profits, loss of enjoyment or use, costs of removal, installation or other
consequential damages of whatsoever nature. Some states do not allow the exclusion or limitation of in-
cidental or consequential damages. Accordingly, the above limitation may not apply to you.
The warranty extended hereunder is in lieu of any and all other warranties and any implied warranties of
merchantability or fitness for a particular purpose is limited in its scope and duration to the terms set
forth herein. Some states do not allow limitations on how long an implied warranty lasts. Accordingly,
the above limitation may not apply to you.
This warranty gives you specific legal rights. You may also have other rights which vary from state to state.
ICON HEALTH & FITNESS, INC., 1500 S. 1000 W., LOGAN, UT 84321-9813
Part No. 167074 R0501A
Printed in USA © 2001 ICON Health & Fitness, Inc.
Download from Www.Somanuals.com. All Manuals Search And Download.
REMOVE THIS EXPLODED DRAWING AND
PART LIST FROM THE MANUAL
Save this EXPLODED DRAWING and PART LIST for future reference.
34
Note: Specifications are subject to change without notice. For information about
ordering replacement parts, see the back cover of the User’s Manual.
Download from Www.Somanuals.com. All Manuals Search And Download.
Part List—Model No. PFHK99902
R0501A
Key
Key
Key
No. Qty. Description
No. Qty. Description
No. Qty. Description
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19*
1
1
1
4
2
Left Foot Rail Insert
Left Foot Rail
Motor Belt
Platform Screw
Belt Guide
50
51
52
53
54
55
56
57
1
1
1
4
4
1
1
1
14” Controller Wire
iFIT.com Connector
iFIT.com Wire
Cage Nut
Upright Bolt (Long)
10’ iFIT.com Audio Cable 101 1
iFIT.com Jack
iFIT.com Wire
96
97
98
99
1
1
1
1
Console Base (Bottom)
Book Holder
Cup Holder/Tray
Console
Upright Wire Harness
Base
6” Audio Wire
Rear Roller
Incline Motor
Wheel Spacer
Resistor Bracket
32” Wire Harness
Endcap Spacer
Ground Wire Screw
Ground Wire
Motor Bushing
Motor Spacer
1” Grommet
Roller Cover Plate
Cover Clip
Bracket Washer
O-Ring
8” Green Wire, F/Ring
6” Green Wire, 2 Ring
4” Green Wire, F/Ring
14” Blue Wire, M/F
8” Blue Wire, M/F
4” Blue Wire, 2F
4” Black Wire, M/F
4” Black Wire
10” Red Wire, 2F
8” Red Wire, 2F
10” White Wire, 2F
User's Manual
100 1
12 Small Screw
1
2
5
1
1
1
1
1
9
1
1
1
1
Walking Platform
Roller Guard
Resistor Screw
Walking Belt
Drive Roller/Pulley
Motor Sleeve
102 1
103 1
104 1
105 4
106 2
107 1
108 3
109 1
110 1
111 2
112 4
113 1
114 1
115 3
116 4
117 2
#
#
#
#
#
#
#
#
#
#
#
#
58 10 Electronics Screw
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77*
78
79
80
81
82
83
84
85
86
87
88
89
90
1
1
4
1
1
2
1
4
2
1
3
3
2
4
1
1
1
1
1
1
1
1
1
2
2
1
1
2
1
1
1
4
Resistor
Electronics Bracket
Plastic Stand-off
Power Board
Controller
Frame Pivot Bolt
Allen Wrench
Frame Bushing
Warning Decal
Static Decal
Roller Adj. Bolt
Roller Adj. Washer
Frame Endcap
Isolator
Flywheel Washer
Motor Pivot Bolt
Motor
Pulley/Flywheel/Fan
Motor/Pulley/Flywheel/Fan
30” Extension Wire
Motor Tension Bolt
Motor Tension Washer
Motor Star Washer
Motor Tension Nut
Small Screw
Magnet
Front Roller Cover
Belly Pan Screw
Belly Pan
Right Foot Rail Insert
Right Foot Rail
Heart Rate Monitor
iFIT.com Module
iFIT.com Videocassette
iFIT.com CD
Upright
Key/Clip
Handrail Bolt
Handrail Star Washer
Handrail
20** 1
21** 1
22** 1
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
2
1
4
4
1
1
6
1
1
6
6
2
2
2
1
1
1
2
1
5
1
1
1
1
1
1
1
1
1
1
1
1
Flywheel Screw
Screw
Handrail Wire Harness
Cup Holder Flange
Internal Star Washer
1” Upright Bolt
Front Wheel
Front Wheel Bolt
Front Wheel Nut
Power Cord
Power Cord Grommet
Circuit Breaker
Frame Pivot Spacer
Base Wire Harness
Base Pad
Plastic Plate
Reed Switch Clip
Upright Endcap
Reed Switch/Wire
Frame
Incline Motor Bolt (Short)
Incline Motor Nut/Frame
Pivot Nut
* Includes all parts shown in the box
**These parts are optional. For infor-
mation about the iFIT.com module,
iFIT.com CD’s, or iFIT.com video-
cassettes, call toll-free 1-800-735-
0768.
43 20 Screw
91
92
93
1
1
1
Rear Endcap (Right)
Incline Motor Insert
Incline Motor Cover
(Bottom)
Incline Motor Cover
(Top)
44
45
46
47
48
49
1
1
1
1
1
1
Releasable Tie
Tie Screw
Tie Holder
8” Cable Tie
On/Off Switch
Outlet Cover
# These parts are not illustrated
94
95
1
1
Incline Motor Bolt (Long)
Download from Www.Somanuals.com. All Manuals Search And Download.
Exploded Drawing—Model No. PFHK99902
R0501A
.
G R O U P
L I T
K i r k N P i R
e
O b D e U r g C T l l
a
Download from Www.Somanuals.com. All Manuals Search And Download.
|