Owner’s Manual
ATTENTION:
Please read the content
of your owner’s manual
before operating your
scooter.
The Ultimate In Style & Performance®
Exeter, PA
St. Catharines, ON
1-800-800-8586
Download from Www.Somanuals.com. All Manuals Search And Download.
C O N T E N T S
I.
INTRODUCTION......................................................................................................................... 4
II. SAFETY ......................................................................................................................................... 6
III. EMI/RFI ........................................................................................................................................ 15
IV. SPECIFICATIONS ................................................................................................................... 17
V. YOUR RALLY ............................................................................................................................ 19
VI. BATTERIES AND CHARGING ........................................................................................... 24
VII. OPERATION............................................................................................................................... 28
VIII.COMFORT ADJUSTMENTS................................................................................................ 30
IX. DISASSEMBLY AND ASSEMBLY..................................................................................... 32
X. OPTIONAL ACCESSORIES................................................................................................. 34
XI. TROUBLESHOOTING............................................................................................................ 35
XII. CARE AND MAINTENANCE ............................................................................................... 36
XIII.WARRANTY................................................................................................................................ 38
Rally/RevF/September 03
3
Download from Www.Somanuals.com. All Manuals Search And Download.
I . I N T R O D U C T I O N
SAFETY
WELCOME to Pride Mobility Products Corporation (Pride). The scooter you have purchased combines state-
of-the-art components with safety, comfort, and styling in mind. We are confident that these design features will
provide you with the conveniences you expect during your daily activities. Once you understand how to safely
operate and care for your scooter, it should give you years of trouble free operation and service.
Read and follow all instructions, warnings, and notes in this manual before attempting to operate your scooter for
the first time. In addition, your safety depends upon you, as well as your Provider, caretaker, or healthcare
professional in using good judgement.
If there is any information in this manual in which you do not understand, or if you require additional assistance for
setup or operation, please contact your authorized Pride Provider. Failure to follow the instructions in this
manual and those located on your scooter can lead to personal injury and/or damage to the scooter,
including voiding the warranty.
EXPRESSED AGREEMENT OF INDEMNIFICATION
In accepting delivery of this product, the Purchaser specifically promises that s/he will not change, alter, or modify
this product or remove or render inoperable or unsafe any guards, shields, or other safety features of the product;
or remove, obliterate, or obstruct any safety and instruction signs, or fail, refuse, or neglect to install any retrofit kits
from time to time provided by Pride to enhance user safety. Purchaser also specifically agrees that if s/he breaches
any such promises, or if s/he is remiss, neglect, or deficient in the safe operation or maintenance of this product, the
purchaser will indemnify and hold harmless Pride from any and all types of actions, suits, claims, or demands,
including products liability claims by purchaser, for injuries or loss arising out of the operation, maintenance, repair,
or other use of this product. Purchaser specifically agrees that this ExpressAgreement of Indemnification is a
condition of sale supported by adequate consideration and was read and understood by the purchaser before
purchasing and delivery of the product.
INFORMATION EXCHANGE
We want to hear your questions, comments, and suggestions about this manual. We would also like to hear about
the safety and reliability of your new scooter, and about the service you received from your authorized Pride
Provider.
Please notify us of any change of address, so we can keep you apprised of important information about safety, new
products, and new options that can increase your ability to use and enjoy your scooter. Please feel free to contact
us at the address below:
Pride Mobility Products Corporation
Attn: Customer Care Department
182 SusquehannaAvenue
Exeter, PA 18643-2694
1-800-424-8205
4
Rally/RevF/September 03
Download from Www.Somanuals.com. All Manuals Search And Download.
I . I N T R O D U C T I O N
PRIDE OWNERS CLUB
As an owner of a Pride product, you are invited to register your product's warranty and enroll in the Pride Owners
Club.You may do so by filling out and returning your enclosed product registration card or by visiting Pride's web
site at www.pridemobility.com.As a registered member, each time you visit our site, you will have access to the
most interactive and honest educational venue available today for people with mobility needs, their families, and
friends.
From our home page, select "Owners Club" to enter a page dedicated to current and potential Pride product
owners.You will gain access to interviews, stories, recreation ideas, daily living tips, product and funding informa-
tion, and interactive message boards. These message boards invite you to communicate with other Pride custom-
ers as well as Pride representatives who are available to assist you with any questions or concerns you may have.
My authorized Pride Provider:
Name:_______________________________________________________________________________
Address:______________________________________________________________________________
Phone Number:_________________________________________________________________________
Purchase Date:_________________________________________________________________________
NOTE:If you ever lose or misplace your product registration card or this owner’s manual, contact us and
we will be glad to send you a new one immediately.
Rally/RevF/September 03
5
Download from Www.Somanuals.com. All Manuals Search And Download.
I I . S A F E T Y
GENERAL
WARNING! Do not operate your new scooter for the first time without completely reading
and understanding this owner’s manual.
Your scooter is a state-of-the-art life-enhancement device designed to increase mobility. Pride provides an exten-
sive variety of products to best fit the individual needs of the scooter user. Please be aware that the final selection
and purchasing decision regarding the type of scooter to be used is the responsibility of the scooter user who is
capable of making such a decision and his/her healthcare professional (i.e., medical doctor, physical therapist,
etc.).
The contents of this manual are based on the expectation that a mobility device expert has properly fitted the
scooter to the user and has assisted the prescribing healthcare professional and/or the authorized Provider in the
instruction process for the use of the product.
There are certain situations, including some medical conditions, where the scooter user will need to practice
operating the scooter in the presence of a trained attendant.Atrained attendant can be defined as a family member
or care professional specially trained in assisting a scooter user in various daily living activities.
As you begin using your scooter during daily activities, you will probably encounter situations in which you will
need some practice. Simply take your time and you will soon be in full and confident control as you maneuver
through doorways, on and off elevators, up and down ramps, and over moderate terrain.
MODIFICATIONS
Your scooter has been designed and engineered to provide maximum mobility and utility.Awide range of accesso-
ries is available from your authorized Pride Provider to further customize your scooter to better suit your needs
and/or preferences. However, under no circumstances should you modify, add, remove, or disable any feature,
part, or function of your scooter.
WARNING! Do not modify your scooter in any way not authorized by Pride. Unauthorized
modifications may result in personal injury and/or damage to your scooter.
REMOVABLE PARTS
WARNING! Do not attempt to lift or move your scooter by any of its removable parts.
Personal injury and damage to the scooter may
ELECTROMAGNETIC FIELDS
Your scooter’s road performance features may be influenced by electromagnetic fields caused by cellular tele-
phones or other radiating devices, such as hand-held radios, radio and television stations, wireless computer links,
microwave sources, and paging transmitters. Learn more about this topic in III. “ EMI/RFI.”
6
Rally/RevF/September 03
Download from Www.Somanuals.com. All Manuals Search And Download.
I I . S A F E T Y
PRE-RIDE SAFETY CHECK
Get to know the feel of your scooter and its capabilities. It is recommended that you perform a safety check before
each use to make sure your scooter operates smoothly and safely. For details on how to perform these necessary
inspections, see XII. “Care and Maintenance.”
Perform the following inspections prior to using your scooter:
n Check for proper tyre inflation. Maintain 30-35 psi in each tyre (if equipped with pneumatic tyres).
n Check all electrical connections. Make sure they are tight and not corroded.
n Check all harness connections. Make sure they are secured properly.
n Check the brakes.
n Check battery charge.
TIRE INFLATION
If your scooter is equipped with pneumatic tires, you should check or have the air pressure checked at least once
a week. Proper inflation pressures will prolong the life of your tires and help ensure the smooth operation of your
scooter.
WARNING! It is critically important that 30-35 psi tire pressure be maintained in pneumatic
tires at all times. Do not underinflate or overinflate your tires. Low pressure may result in
loss of control, and overinflated tires may burst. Failure to maintain 30-35 psi tire pressure
in pneumatic tires at all times may result in tire and/or wheel failure, causing serious
personal injury and/or damage to your scooter.
WARNING! Inflate your scooter tires from a regulated air source with an available pressure
gauge. Inflating your tires from an unregulated air source could overinflate them, resulting
in a burst tire and/or personal injury.
WEIGHT LIMITATIONS
Your scooter is rated for a maximum weight capacity. Refer to the specifications table for information.
WARNING! Exceeding the weight limit voids your warranty and may result in personal
injury and damage to your scooter. Pride will not be held responsible for injuries and/or
property damage resulting from failure to observe weight limitations.
WARNING! Do not carry passengers on your scooter. Carrying passengers on your scooter
may result in personal injury and/or property damage.
INCLINE INFORMATION
More and more buildings have ramps with specified percents of inclination, designed for easy and safe access.
Some ramps may have turning switchbacks (180-degree turns) that require you to have good cornering skills on
your scooter.
n Proceed with extreme caution as you approach the downgrade of a ramp or other incline.
n Take wide swings with your scooter’s front wheel(s) around any tight corners. If you do that, the scooter’s rear
wheels will follow a wide arc, not cut the corner short, and not bump into or get hung up on any railing corners.
n When driving down a ramp, keep the scooter’s speed adjustment set to the slowest speed setting to ensure a
safely controlled descent. See V. “Your Rally.”
n Avoid sudden stops and starts.
Rally/RevF/September 03
7
Download from Www.Somanuals.com. All Manuals Search And Download.
I I . S A F E T Y
When climbing an incline, try to keep your scooter moving. If you must stop, start up again slowly, and then
accelerate cautiously.When driving down an incline, do so by setting the speed adjustment to the slowest setting
and driving in the forward direction only. If your scooter starts to move down the incline faster than you anticipated
or desired, allow it to come to a complete stop by releasing the throttle control lever.Then push the throttle control
lever forward slightly to ensure a safely controlled descent.
WARNING! When climbing an incline, do not zigzag or drive at an angle up the face of the
incline. Drive your scooter straight up the incline. This greatly reduces the possibility of a
tip or a fall. Always exercise extreme caution when negotiating an incline.
WARNING! Do not drive your scooter across the side of a hill or diagonally up or down a
hill; do not stop, if possible, while driving up or down an incline.
WARNING! You should not travel up or down a potentially hazardous incline (i.e., areas
covered with snow, ice, cut grass, or wet leaves).
WARNING! When on any sort of an incline or decline, never place the scooter in freewheel
mode while seated on it or standing next to it.
WARNING! Even though your scooter is capable of climbing slopes greater than those
illustrated in figures 1 and 1A, do not, under any circumstances, exceed the incline
guidelines or any other specifications presented in this manual. Doing so could cause
instability in your scooter, resulting in personal injury and/or damage to your scooter.
Handicap public access ramps are not subject to government regulation in all countries, and therefore do not
necessarily share the same standard percent of slope. Other inclines may be natural or, if man-made, not designed
specifically for scooters. Figures 1 and 1Aillustrate your scooter’s stability and its ability to climb grades under
various weight loads and under controlled testing conditions.
These tests were conducted with the scooter’s seat in the highest position and adjusted backward on the seat base
to its farthest backward position. Use this information as a guideline. Your scooter’s ability to travel up inclines is
affected by your weight, your scooter’s speed, your angle of approach to the incline, and your scooter setup.
150 lbs.
5°
300 lbs.
3°
200 lbs.
5°
200 lbs. 300 lbs.
4° 2°
150 lbs.
5°
Figure 1. Maximum Recommended
3-Wheel Incline Angles
Figure 1A. Maximum Recommended
4-Wheel Incline Angles
WARNING! Any attempt to climb or descend a slope steeper than what is shown in figures
1 and 1A may put your scooter in an unstable position and cause it to tip, resulting in
personal injury.
WARNING! Never carry an oxygen tank weighing more than 15 lbs. Never fill the rear
basket with contents exceeding 15 lbs.
8
Rally/RevF/September 03
Download from Www.Somanuals.com. All Manuals Search And Download.
I I . S A F E T Y
When you approach an incline, it is best to lean forward. See figures 2 and 2A. This shifts the center of gravity of
you and your scooter toward the front of the scooter for improved stability.
Figure 2. Normal Driving Position
Figure 2A. Increased Stability Driving Position
CORNERING INFORMATION
Excessively high cornering speeds can create the possibility of tipping. Factors which affect the possibility of
tipping include, but are not limited to, cornering speed, steering angle (how sharply you are turning), uneven road
surfaces, inclined road surfaces, riding from an area of low traction to an area of high traction (such as passing
from a grassy area to a paved area – especially at high speed while turning), and abrupt directional changes. High
cornering speeds are not recommended. If you feel that you may tip over in a corner, reduce your speed and
steering angle (i.e., lessen the sharpness of the turn) to prevent your scooter from tipping.
WARNING! When cornering sharply, reduce your speed. When using your scooter at
higher speeds, do not corner sharply. This greatly reduces the possibility of a tip orafll.
To avoid personal injury or pr operty damage, always exercise common sense when
cornering.
Rally/RevF/September 03
9
Download from Www.Somanuals.com. All Manuals Search And Download.
I I . S A F E T Y
OUTDOOR DRIVING SURFACES
Your scooter is designed to provide optimum stability under normal driving conditions—dry, level surfaces com-
posed of concrete, blacktop, or asphalt. However, Pride recognizes that there will be times when you will encoun-
ter other surface types. For this reason, your scooter is designed to perform admirably on packed soil, grass, and
gravel. Feel free to use your scooter safely on lawns and in park areas.
n Reduce your scooter’s speed when driving on uneven terrain and/or soft surfaces.
n Avoid tall grass that can become tangled in the running gear.
n Avoid loosely packed gravel and sand.
n If you feel unsure about a driving surface, avoid that surface.
STATIONARY OBSTACLES (STEPS, CURBS, ETC.)
WARNING! Do not drive near raised surfaces, unprotected ledges, and/or drop-offs (curbs,
porches, stairs, etc.).
WARNING! Do not attempt to have your scooter climb or descend an obstacle that is
inordinately high. Serious personal injury and/or damage may result.
WARNING! Do not attempt to have your scooter proceed backward down any step, curb, or
other obstacle. This may cause thescooter to tip and cause personal injury.
WARNING! Be sure your scooter is traveling perpendicular to any curb you may be required
to ascend or descend. See figures 3 and 3A.
WARNING! Do not attempt to negotiate a curb that has a height greater than 2 in.
Figure 3. Correct Curb Approach
Figure 3A. Incorrect Curb approach
BRAKING INFORMATION
Your scooter is equipped with two powerful brake systems:
1. Regenerative: Uses electricity to rapidly slow the vehicle when the throttle control lever returns to the center/
stop position; and
2. Disc Park Brake:Activates mechanically after regenerative braking slows the vehicle to near stop, or when
power is removed from the system for any reason.
10
Rally/RevF/September 03
Download from Www.Somanuals.com. All Manuals Search And Download.
I I . S A F E T Y
PUBLIC STREETS AND ROADWAYS
WARNING! You should not operate your scooter on public streets and roadways. Be aware
that it may be difficult for traffic to see you when you are seated on your scooter. Obey all
local pedestrian traffic rules. Wait until your path is clear of traffic, and then proceed with
extreme caution.
NOTE: Safety accessories like fluorescent flags are available to order from your authorized Pride Provider.
INCLEMENT WEATHER PRECAUTIONS
WARNING! Pride recommends that you do not operate your scooter in icy or slippery
conditions or on salted surfaces (i.e., walks or roads). Such use may result in an accident,
personal injury, or adversely affect the performance and safety of your scooter.
WARNING! Do not operate or store your scooter where it may be exposed to inclement
weather conditions such as rain, snow, mist, and below freezing temperatures (such as
storage on an outside car/van lift). Attempting to operate the scooter in such conditions
can damage the electronics and potentially result in loss of control.
FREEWHEEL MODE
Your scooter is equipped with a manual freewheel lever that when pulled up allows the scooter to be pushed. For
more information about how to place your scooter into and out of freewheel mode, seeV. “Your Rally.”
WARNING! When your scooter is in freewheel mode, the braking system is disengaged.
n Disengage the drive motors only on a level surface.
n Ensure the key is removed from the key switch.
n Stand behind the scooter to engage or disengage freewheel mode. Never sit on a
scooter to do this.
n After you have finished pushing your scooter, always return it to the drive mode to lock
the brakes.
Failure to heed the above could result in personal injury and/or damage to your scooter.
An added feature built into the scooter is “push-too-fast” protection which safeguards the scooter against gaining
excessive speed while in freewheel mode.
“Push-too-fast” operates differently depending on which of two conditions exists:
n If the key is removed from the key switch while in freewheel mode, the scooter’s controller activates regenera-
tive braking when the scooter is pushed faster than a maximum threshold which has been preprogrammed. In
this case, the controller is acting as a speed governor.
n If the key is fully inserted into the key switch while in freewheel mode, you will encounter considerable
resistance at any speed.This prevents the scooter from gaining unwanted momentum should the manual free-
wheel lever inadvertently be released while driving the scooter.
Rally/RevF/September 03
11
Download from Www.Somanuals.com. All Manuals Search And Download.
I I . S A F E T Y
STAIRS AND ESCALATORS
Scooters are not designed to travel up or down stairs or escalators. Always use an elevator.
WARNING! Do not use your scooter to negotiate steps or escalators. You may cause injury
to yourself and to others and/or damage your scooter.
DOORS
n Determine if the door opens toward or away from you.
n Use your hand to turn the knob or push the handle or push-bar.
n Drive your scooter gently and slowly forward to push the door open. Or drive your scooter gently and slowly
backward to pull the door open.
ELEVATORS
Modern elevators have a door edge safety mechanism that, when pushed, reopens the elevator door(s).
n If you are in the doorway of an elevator when the door(s) begin to close, push on the rubber door edge or
allow the rubber door edge to contact the scooter and the door will reopen.
n Use care that pocketbooks, packages, or scooter accessories do not become caught in elevator doors.
LIFT/ELEVATION PRODUCTS
If you will be traveling with your scooter, you may find it necessary to use a lift/elevation product to aid in transpor-
tation. It is recommended that you closely review the instructions, specifications, and safety information set forth by
the manufacturer of the lift/elevation product before using that product.
WARNING! Never sit on your scooter when it is being used in connection with any type of
lift/elevation product. Your scooter was not designed with such use in mind, and any
damage or injury incurred from such use is not the responsibility of Pride.
BATTERIES
In addition to following the warnings below, be sure to comply with all other battery handling information. For
more information about your scooter’s batteries, see VI. “ Batteries and Charging.”
WARNING! Scooter batteries are heavy (refer to specifications table). Lifting weight
beyond your capacity could result in personal injury. If necessary, get someone physically
able to lift the scooter batteries for you.
WARNING! Battery posts, terminals, and related accessories contain lead and lead
compounds. Wash hands after handling.
WARNING! Always protect the batteries from freezing and never charge a frozen battery.
Charging a frozen battery may result in personal injury and/or damage to the battery.
WARNING! RED (+) cables must be connected to positive (+) battery terminals/posts. BLACK
(-) cables must be connected to negative (-) battery terminals/posts. Failure to connect
your battery harnesses in the proper manner may result in personal injury and/or damage
to your scooter. REPLACE cables immediately if damaged.
12
Rally/RevF/September 03
Download from Www.Somanuals.com. All Manuals Search And Download.
I I . S A F E T Y
BATTERY DISPOSAL AND RECYCLING
If you encounter a damaged or cracked battery, immediately enclose it in a plastic bag and call your authorized
Pride Provider for instructions on disposal. Your authorized Pride Provider will also have the necessary informa-
tion on battery recycling, which is our recommended course of action.
PREVENTING UNINTENDED MOVEMENT
WARNING! If you anticipate being seated in a stationary position for an extended period
of time, turn off the power. This will prevent unexpected motion from inadvertent throttle
control lever contact. Failure to do so may result in personal injury.
MOTOR VEHICLE TRANSPORT
Currently, there are no standards approved for tie-down systems in a moving vehicle of any type to transport a
person while seated in a scooter.
Although your scooter may be equipped with a positioning belt, this belt is not designed to provide proper restraint
during motor vehicle transport.Anyone traveling in a motor vehicle should be properly secured in the motor vehicle
seat with safety belts fastened securely.
WARNING! Do not sit on your scooter while it is in a moving vehicle. Personal injury and/or
property damage may result.
WARNING! Always be sure your scooter and its batteries are properly secured when it is
being transported. Failure to do so may result in personal injury and/or damage to your
scooter.
GETTING ONTO AND OFF OF YOUR SCOOTER
Getting onto and off of your scooter requires a good sense of balance. Please observe the following safety tips
when getting onto and off of your scooter:
n Power down your scooter. See VII. “Operation.”
n Ensure that your scooter is not in freewheel mode. See V. “Your Rally.”
n Make certain that the seat is locked into place and the key is removed from the key switch.
n The seat armrests can be flipped up to make getting onto and off of your scooter easier.
WARNING! Position yourself as far back as possible in the scooter seat to prevent the
scooter from tipping and causing injury.
WARNING! Avoid using the armrests for weight bearing purposes. Such use may cause the
scooter to tip and cause personal injury.
WARNING! Avoid putting all of your weight on the floorboard. Such use may cause the
scooter to tip and cause personal injury.
Rally/RevF/September 03
13
Download from Www.Somanuals.com. All Manuals Search And Download.
I I . S A F E T Y
POSITIONING BELTS
Your authorized Provider, therapist(s), and other healthcare professionals are responsible for determining your
requirement for a positioning belt in order to operate your scooter safely.
WARNING! If you require a positioning belt to safely operate your scooter, make sure it is
fastened securely. Serious personal injury may result if you fall from the scooter.
REACHING AND BENDING
Avoid reaching or bending while driving your scooter.When reaching, bending, or leaning while seated on your
scooter, it is important to maintain a stable center of gravity and keep the scooter from tipping. It is recommended
that the scooter user determine his/her personal limitations and practice bending and reaching in the presence of a
qualified healthcare professional.
WARNING! Do not bend, lean, or reach for objects if you have to pick them up from the
floor by reaching down between your knees. Movements such as these may change your
center of gravity and the weight distribution of the scooter and cause your scooter to tip,
possibly resulting in personal injury. Keep your hands away from the tires when driving.
PRESCRIPTION DRUGS/PHYSICAL LIMITATIONS
The scooter user must exercise care and common sense when operating his/her scooter.This includes awareness of
safety issues when taking prescribed or over-the-counter drugs or when the user has specific physical limitations.
WARNING! Consult your physician if you are taking prescribed or over-the-counter
medication or if you have certain physical limitations. Some medications and limitations
may impair your ability to operate your scooter in a safe manner.
ALCOHOL
The scooter user must exercise care and common sense when operating his/her scooter.This includes awareness
of safety issues while under the influence of alcohol.
WARNING! Do not operate your scooter while you are under the influence of alcohol, as
this may impair your ability to drive safely.
14
Rally/RevF/September 03
Download from Www.Somanuals.com. All Manuals Search And Download.
I I I . E M I / R F I
EMI/RFI WARNINGS
Laboratory tests performed by the Food and DrugAdministration (FDA) have shown that radio waves can cause
unintended motion of electric mobility vehicles. Radio waves are a form of electromagnetic energy (EM). When
electromagnetic energy adversely affects the operation of an electrical device, that adverse effect is called Electro-
magnetic Interference (EMI) or Radio Frequency Interference (RFI).
EMI/RFI FREQUENTLY ASKED QUESTIONS (FAQS)
The following FAQs summarize what you should know about EMI/RFI. Use this information to minimize the risk
that EMI/RFI will adversely affect your mobility vehicle.
Where do radio waves come from?
Radio waves are emitted from the antennas of cellular phones, mobile two-way radios (such as walkie-talkies and
CBs), radio stations, TV stations, amateur radio (HAM) transmitters, wireless computer links, microwave sources,
and paging transmitters. Radio waves are a form of electromagnetic energy (EM). EM is more intense closer to
transmitting antennas, which are sources of emission. The greater the transmission strength, the greater the concern
to electric mobility vehicle users.
If EMI/RFI affects my mobility vehicle, what kind of motion should I expect?
This is difficult to predict. The answer would depend on a number of factors:
n The strength of the radio waves.
n The construction of your particular mobility vehicle.
n The location of your mobility vehicle (whether it is on the level ground or on an incline).
n Whether or not your mobility vehicle is in motion.
The motion of any electric mobility vehicle affected by EMI/RFI can be erratic. The mobility vehicle may come to
a sudden stop or move in an uncontrolled manner.Also, it is possible for EMI/RFI to release the brakes of an
electric mobility vehicle. Some intense EMI/RFI can even damage the control system components of an electric
mobility vehicle.
Is there any way to know for certain whether or not radio waves are the cause of any unintended
mobility vehicle motion?
Unfortunately, EMI/RFI may be difficult to recognize, because the signals from radio sources are invisible and may
be intermittent. However, the FDArecommends that you report all incidents of unintended motion or unintended
brake release of your mobility vehicle to its manufacturer and, if possible, determine whether or not there was a
radio wave source nearby at the time of the incident.
One precaution you can take against unintended motion of your mobility vehicle is to make certain that you or
someone else is not the cause of the unintended motion.
n Turn off your mobility vehicle by removing the key from the key switch when you are getting onto or off of your
mobility vehicle.
n Never leave the key in the key switch of an unattended mobility vehicle.
n By following these steps, you greatly reduce the risk of you or anyone else inadvertently bumping the throttle
control levers and causing the mobility vehicle to move unintentionally.
Has anyone been injured by the erratic, unintended motion of an electric mobility vehicle?
The FDA has reports of injuries that resulted from uncontrolled motion of electric mobility vehicles, but it is not
clear just how many of those injuries were actually caused by EMI/RFI.
Rally/RevF/September 03
15
Download from Www.Somanuals.com. All Manuals Search And Download.
I I I . E M I / R F I
Are all electric mobility vehicles susceptible to EMI/RFI?
Each make and model of electric mobility vehicle differs in its ability to resist EMI/RFI. Every mobility vehicle has
a particular level of resistance to EMI/RFI. This resistance is measured in volts per meter (V/m).A higher resis-
tance level offers greater protection against EMI/RFI. In other words, an electric mobility vehicle with a high
resistance level is less likely to be affected by a strong radio source than is an electric mobility vehicle with a low
resistance level.
What is the FDA doing about the problem?
The FDA has written to electric mobility vehicle manufacturers and requested that those manufacturers test their
new mobility vehicle models to be certain that they provide a reasonable degree of resistance against EMI/RFI.
The FDA has stated that all newly manufactured electric mobility vehicle models should have a resistance level of
at least 20 V/m. This level of resistance provides a reasonable degree of protection against the common sources of
EMI/RFI.
The FDA has also requested or recommended that:
n Electric mobility vehicle manufacturers clearly label new products with their resistance level or state that the
resistance level is not known.
n The labeling or informational material supplied with new electric mobility vehicles must explain what the resis-
tance level means and warn users about the possibility of EMI/RFI and how to avoid it.
n Electric mobility vehicle manufacturers undertake an educational program to inform electric mobility vehicle
users and their caregivers about the problems associated with EMI/RFI and about the actions they can take to
minimize the risk of EMI/RFI.
n While there is no exact way to tell if your mobility vehicle is totally safe, an immunity level of 20 V/m isgenerally
achievable and useful. This product has been tested and passed at an immunity level of 20 V/m.
What can I do to find out if my mobility vehicle is likely to be affected by EMI/RFI?
If you have had your mobility vehicle for some time and have not experienced any unintended motion, it is not likely
that you will have a problem in the future. However, it is always possible that EMI/RFI problems could arise if you
are close to a source of radio waves. Therefore, it is very important for you to be alert to this possibility. The
mobility vehicle meets or exceeds a resistance level of at least 20 V/m.
What can I do to reduce the risk of my mobility vehicle being affected by EMI/RFI?
Here are some precautions you can take:
n Do not turn on or use hand-held personal communications devices, such as citizens band (CB) radios and
cellular phones, while your mobility vehicle is turned on.
n Be aware of nearby radio wave transmitters, such as radio or TV stations and hand-held or mobile two-way
radios. Try not to operate your mobility vehicle too close to those transmitters. For example, if you are on an
electric mobility vehicle with a resistance level of at least 20 V/m, you should remain at least three feet from a
hand-held two-way radio and at least ten feet from a mobile two-way radio.
n Be aware that adding accessories and/or components, or modifying your mobility vehicle in any way, may
change its EMI/RFI resistance level and may make it more susceptible to interference from radio wave sources.
What should I do if my mobility vehicle moves unexpectedly?
If unintended motion or unintended brake release occurs, turn off your mobility vehicle (by removing the key) as
soon as it is safe to do so.
If my mobility vehicle moves unintentionally, where should I report the incident?
Call Pride Customer Care at 1-800-424-8205 to report the incident.
16
Rally/RevF/September 03
Download from Www.Somanuals.com. All Manuals Search And Download.
I V . S P E C I F I C A T I O N S
13"
7.5"
80˚
16.5" - 18.5"
3"
44"Length
(4-Wheel Rally)
18"
41"Length
(3-Wheel Rally)
16"
(22" - 29")
39"
54"
4-Wheel Rally Turning Radius
3-Wheel Rally Turning Radius
Figure 4. Rally Dimensions
21"
2.5"
2"
8"
9"
Figure 4A. Rally Tire Dimensions (Front)
Figure 4B. Rally Tire Dimensions (Rear)
Rally/RevF/September 03
17
Download from Www.Somanuals.com. All Manuals Search And Download.
I V . S P E C I F I C A T I O N S
Model Number
Available Colors
Overall Length
3-wheel: SC151, 4-wheel: SC155
Candy Apple Red, Viper Blue
3-wheel: 41 in
4-wheel: 44 in.
Overall Width
21 in.
Total Weight Without Batteries
Heaviest Piece When Disassembled
Turning Radius
3-wheel: 93 lbs.
4-wheel: 116 lbs.
3-wheel: rear section 42 lbs.
4-wheel: front section 45 lbs.
3-wheel: 39 in.
4-wheel: 54 in.
Maximum Speed
Range Per Charge*
Ground Clearance
Weight Capacity
Standard Seating
Up to 4.25 mph, 60% reverse (may vary with terrain)
Up to 25 miles with 32 AH batteries
3 in.
300 lb. maximum
Type: Foldable molded plastic
Dimensions: width 18 in. x depth 16 in. (usable) x height 13 in. (usable)
Material: Vinyl: Gray
Fabric: Gray
Drive System
Dual Braking System
Wheels
Rear-wheel drive, 24V sealed transaxle
Electronic, regenerative, and electromechanical
Black aluminum alloy mags
Tires (front)
8 in. x 2 in.
Tires (rear)
9 in. x 2.5 in.
Battery Requirements
Type: 12V deep-cycle (SLA or Gell Cell)
Size: U-1 (32 AH only) or 17 AH
Onboard
Battery Charger
Warranty
3-year limited
Accessories and Options
Single/cane crutch holder, dual cane/crutch holder, double crutch
holder, oxygen tank holder, walker holder, forearm crutch holder, cup
holder, dust cover, safety flag, rear basket, taillight, saddle bag (arm
mount), quad cane holder
*Varies with user weight, terrain type, battery charge, battery condition, and tire condition.
18
Rally/RevF/September 03
Download from Www.Somanuals.com. All Manuals Search And Download.
V . Y O U R R A L L Y
Your Rally is a motorized electric scooter designed to enhance your personal mobility.Your Rally is an indoor/
outdoor scooter that was designed to travel primarily on smooth surfaces, such as pavement, roads, parking lots,
floors, and driveways. For easy transportation or storage, you can disassemble your scooter into seven compo-
nents. See figure 5.
REAR SECTION
SEAT
FRONT SECTION
BATTERIES
REAR SHROUD
BASKET
Figure 5. Scooter Components
CONTROL CONSOLE ASSEMBLY
The control console assembly houses all of the controls you need to drive your scooter including the key switch, the
speed adjustment dial, the throttle control lever, the battery condition meter, the horn button, and the light switch.
See figure 6.
WARNING! Do not expose the control console assembly to moisture. In the event that the
console does become exposed to moisture, do not attempt to operate your scooter until
the control console assembly has thoroughly dried.
BATTERY CONDITION METER
KEY SWITCH
KEY
SPEED
ADJUSTMENT
DIAL
LIGHT SWITCH
HORN BUTTON
THROTTLE
CONTROL LEVER
(FORWARD)
THROTTLE
CONTROL LEVER
(REVERSE)
Figure 6. Control Console Assembly
Rally/RevF/September 03
19
Download from Www.Somanuals.com. All Manuals Search And Download.
V . Y O U R R A L L Y
Key Switch
n Fully insert the key into the key switch to power up (turn on) your scooter.
n Pull the key out to power down (turn off) your scooter.
WARNING! If the key is removed from the key switch while your scooter is in motion, the
electronic brakes engage and your scooter comes to an abrupt stop!
Speed Adjustment Dial
This control dial allows you to preselect and limit your scooter’s top speed.
n The image of the tortoise represents the slowest speed setting.
n The image of the hare represents the fastest speed setting.
Throttle Control Lever
This lever allows you to control the forward and the reverse speed of your scooter up to the maximum speed
preset by the speed adjustment dial.
n Place your right hand on the right handgrip and your left hand on the left handgrip.
n Use your right thumb to push the right side of the lever to disengage your scooter’s brake and move forward.
n Release the lever and allow your scooter to come to a complete stop before pushing the other side of the lever
to move in reverse.
n When the throttle is completely released, it automatically returns to the center “stop” position and engages your
scooter’s brake.
Battery Condition Meter
This meter gives an approximate reading of your scooter’s battery voltage when the key is fully inserted into the
key switch.
NOTE: To ensure the highest accuracy, the battery condition meter should be checked while operating
your scooter at full speed on a dry, level surface.
Horn Button
n The key must be fully inserted into the key switch for the horn to be operational.
n This button activates a warning horn.
n Do not hesitate to use the warning horn when its use could prevent accident or injury.
Light Switch
This switch controls your scooter’s headlight system.
n Press this switch once to turn on the lights.
n Press it again to turn off the lights.
20
Rally/RevF/September 03
Download from Www.Somanuals.com. All Manuals Search And Download.
V . Y O U R R A L L Y
REAR SECTION
The onboard battery charger, the charger power cord receptacle, the battery charger fuse, the batteries, the
electronic controller assembly, the main circuit breaker, the manual freewheel lever, and the motor/transaxle as-
sembly are located on the rear section of your scooter. See IX. “Disassembly andAssembly” for instructions on
removing the rear shroud. The anti-tip wheels are at the rearmost part of your scooter. See figure 7.
BATTERIES
ELECTRONIC CONTROLLER
ASSEMBLY
MAIN CIRCUIT BREAKER
(RESET BUTTON)
ONBOARD BATTERY
CHARGER
CHARGER POWER
CORD RECEPTACLE
BATTERY CHARGER
FUSE
MANUAL FREEWHEEL
LEVER
MOTOR/TRANSAXLE ASSEMBLY
ANTI-TIP WHEELS
Figure 7. Rear Section
Onboard Battery Charger
The onboard battery charger converts household alternating current (AC) to direct current (DC) and charges the
batteries of your scooter. See VI. “Batteries and Charging.”
n The charger is a box with cooling fins on the exterior of its case.
n The charger power cord plugs into the battery charger by means of a receptacle located on the rear section of
your scooter, near the manual freewheel lever and the main circuit breaker reset button. See figure 7.
Electronic Controller Assembly
This assembly receives electrical signals from the console controls and sends power to the motor, the brake
systems.
Rally/RevF/September 03
21
Download from Www.Somanuals.com. All Manuals Search And Download.
V . Y O U R R A L L Y
Battery Charger Fuse
The fuse has been incorporated into your charger to protect it from damage in the event of an electrical problem.
If your charger fuse repeatedly blows, try plugging your scooter’s power charger cord into an outlet on a different
circuit.
n The fuse is located under a cap on the outside of the battery charger.
n The cap unscrews to allow access to the fuse.
n Unscrew the cap and replace the fuse if it has blown.
WARNING! The replacement fuse must exactly match the rating of the new fuse. Failure
to use properly rated fuses may cause damage to the electrical system and may result in
personal injury.
Batteries
The batteries store the electrical energy that powers your scooter. See VI. “Batteries and Charging.”
Main Circuit Breaker
When the voltage in your scooter’s batteries becomes low or your scooter is heavily strained because of excessive
loads or steep inclines, the main circuit breaker may trip to protect your scooter’s motor and electronics from
damage.
n The main circuit breaker is mounted on the rear section of the scooter, near the manual freewheel lever. See
figure 7.
n The main circuit breaker reset button pops out when the breaker trips.
n When the breaker trips, the entire electrical system of your scooter is shut down.
n Allow a minute or so for your scooter’s electronics to “rest.”
n Push in the reset button to reset the breaker.
n If the breaker trips frequently, you may need to charge your batteries more often. You may also need to have
your authorized Pride Provider perform a load test on your scooter’s batteries.
n If the main circuit breaker trips repeatedly, see your authorized Pride Provider for service.
Manual Freewheel Lever
Whenever you need or want to push your scooter for short distances, you can put it in freewheel mode. See figure 7.
WARNING! When your scooter is in freewheel mode, the braking system is disengaged.
n Disengage the drive motors only on a level surface.
n Ensure the key is removed from the key switch.
n Stand behind the scooter to engage or disengage freewheel mode. Never sit on a
scooter to do this.
n After you have finished pushing your scooter, always return it to the drive mode to lock
the brakes.
Failure to heed the above could result in personal injury and/or damage to your scooter.
n Pull up on the manual freewheel lever to disable the drive system and the brake system. You will then be able
to push your scooter.
n Push down on the manual freewheel lever to reengage the drive system and the brake system and to take your
scooter out of freewheel mode.
22
Rally/RevF/September 03
Download from Www.Somanuals.com. All Manuals Search And Download.
V . Y O U R R A L L Y
Motor/Transaxle Assembly
The motor/transaxle assembly consists of a geared transmission and differential. This one piece, direct drive, fully
sealed assembly provides quiet operation with maximum power and long life. See figure 7.
Anti-Tip Wheels
The anti-tip wheels are an integral and important safety feature of your scooter. Do not, under any circumstances,
remove the anti-tip wheels from your scooter.
WARNING! Do not remove the anti-tip wheels or modify your scooter in any way that is not
authorized by Pride.
Rally/RevF/September 03
23
Download from Www.Somanuals.com. All Manuals Search And Download.
V I . BATTERIES AND C H A R G ING
Your scooter requires two long-lasting, 12-volt, deep-cycle batteries that are sealed and maintenance free. They
are recharged by an onboard 3-amp charging system designed for ease of use and convenience.
n Charge your scooter’s batteries prior to using it for the first time.
n Keepyourbatteriesfullychargedtokeepyourscooterrunningtroublefree.
Youhavetheoptiontouseeither32AHor17AHbatteriesforyourscooter.
Yourscooterwaspresettouse32AHbatteries. Ifyoudecidetouse17AH
batteries, youmustinstallthetwoprovidedbatteryspacerbrackets.
BATTERY
SPACER
BRACKET
Follow these easy steps to install the battery spacer brackets:
1. Position the spacer bracket in the battery well. See figure 8.
2. Aligntheholesinthespacerbracketwiththeholesinthebatterywell.
Figure 8. Positioning The battery
Spacer Bracket
3. Install the Christmas tree clips. See figure 8A.
4. Repeat steps 1-3 for the second spacer bracket.
CHRISTMAS TREE CLIP
READING YOUR BATTERY VOLTAGE
The battery condition meter on the control console assembly indi-
catestheapproximatestrengthofyourbatteriesusingacolorcode. Green
indicates fully charged batteries, yellow a draining charge, and red indi-
cates that an immediate recharge is necessary. See figure 9. To ensure
the highest accuracy, the battery condition meter should be checked
while operating your scooter at full speed on a dry, l evel surface.
Figure 8A. Installing The Christmas
Tree Clips
CHARGING YOUR BATTERIES
Follow these easy steps to charge your batteries safely:
WARNING! Never use an extension cord to plug
in your battery charger. Plug the charger directly
into a properly wired standard wall outlet.
WARNING! Removal of the grounding prong can
create an electrical hazard. If necessary
properly install an approved 3-prong adaptor to
an electrical outlet having 2-pronged plug
access. Failure to heed could result in personal
injury and or property damage.
Figure 9. Battery Condition Meter
1. Position your scooter close to a standard wall outlet.
2. Remove the key from the key switch.
3. Make certain that the manual freewheel lever is in the drive (down) position.
4. Plug the charger power cord into the charger power cord receptacle.
5. Plug the charger power cord into a standard wall outlet.
6. When the batteries are fully charged, unplug the charger power cord from the wall outlet and then from the
charger power cord receptacle.
NOTE: There is a charger inhibit function on your scooter. The scooter will not run and the battery
condition meter will not operate while the batteries are charging.
24
Rally/RevF/September 03
Download from Www.Somanuals.com. All Manuals Search And Download.
V I . BATTERIES AND CHARGING
FREQUENTLY ASKED QUESTIONS (FAQS)
How does the charger work?
When your scooter’s battery voltage is low, the charger works harder, sending more electrical current to the
batteries to bring up their charge.As the batteries approach a full charge, the charger sends less and less electrical
current. When the batteries are fully charged, the current sent from the charger is at nearly zero amperage. There-
fore, when the charger is plugged in, it maintains the charge on your scooter’s batteries, but does not overcharge
them. We do not recommend that you charge your scooter’s batteries for more than 24 consecutive hours.
What if my scooter’s batteries won’t charge?
n Ensure that the red (+) and black (-) battery cables are connected properly to the battery terminals.
n Ensure both battery harnesses that extend from the batteries are plugged into their mating harness leading to the
charger.
n Ensure that both ends of the charger power cord are inserted fully.
Can I use a different charger?
For the safest, most efficient, and balanced charging of your scooter’s batteries, we prefer and highly recommend
simultaneous charging of both batteries with the onboard battery charger.
How often must I charge the batteries?
Two major factors must be considered when deciding how often to charge your scooter’s batteries:
n All day scooter use on a daily basis.
n Infrequent or sporadic scooter use.
With these considerations in mind, you can determine how often and for how long you should charge your scooter’s
batteries. We designed the onboard charger so that it will not overcharge your scooter’s batteries. However, you
may encounter some problems if you do not charge your batteries often enough and if you do not charge them on
a regular basis. Following the guidelines below will provide safe and reliable battery operation and charging.
n If you use your scooter daily, charge its batteries as soon as you finish using it for the day.Your scooter will be
ready each morning to give you a full day of service. We recommend that you charge your scooter’s batteries
for 8 to 14 hours after daily use.
n If you use your scooter once a week or less, charge its batteries at least once a week for 12 to 14 hours at a
time.
n Keep your scooter’s batteries fully charged.
n Avoid deeply discharging your scooter’s batteries.
How can I ensure maximum battery life?
Fully charged deep-cycle batteries provide reliable performance and extended battery life. Keep your scooter’s
batteries fully charged whenever possible. Batteries that are regularly and deeply discharged, infrequently charged,
or stored without a full charge may be permanently damaged, causing unreliable performance and limited service life.
Rally/RevF/September 03
25
Download from Www.Somanuals.com. All Manuals Search And Download.
V I . BATTERIES AND CHARGING
How can I get maximum range or distance per charge?
Rarely will you have ideal driving conditions—smooth, flat, hard driving surfaces with no wind or curves. Often, you will
face hills, pavement cracks, uneven and loosely packed surfaces, curves, and wind, all of which affect the distance or
running time per battery charge. Below are a few suggestions for obtaining the maximum range per battery charge.
n Always fully chargeyour scooter’s batteries prior to daily use.
n Maintain 30-35 psi (pounds per square inch) in each tire.
n Plan your route ahead to avoid as many hills, cracked, broken, or soft surfaces as possible.
n Limit your baggage weight to essential items.
n Try to maintain an even speed while your scooter is in motion.
n Avoid stop-and-go driving.
What type and size of battery should I use?
We recommend deep-cycle batteries that are sealed and maintenance free. BothAGM and Gel-Cell are deep-cycle
batteries that are similar in performance. Do not use wet-cell batteries, which have removable caps.
NOTE: Sealed batteries are not serviceable. Do not remove the caps.
Use these specifications to reorder batteries:
Type:
Size:
Voltage:
Amperage:
Deep-cycle (AGM orGel-Cell)
U-1 (32AH only)
12 volts each
32AH, 17AH
WARNING! Corrosive chemicals contained in batteries. Use only AGM or Gel-Cell batteries
to reduce the risk of leakage or explosive conditions.
To change a battery in your scooter:
WARNING! Battery posts, terminals, and related accessories contain lead and lead
compounds. Wash hands after handling.
1. Remove the seat and rear shroud.
2. Disconnect the battery tie-down strap.
3. Disconnect the battery harness.
4. Disconnect the battery cables from the battery terminals.
5. Remove the old battery.
6. Place a new battery in the battery well.
7. Connect the red battery cable to the positive (+) battery terminal.
8. Connect the black battery cable to the negative (-) battery terminal.
9. Reconnect the battery harness.
10. Reconnect the battery tie-down strap.
11. Reinstall the rear shroud and seat.
BATTERY DISPOSAL AND RECYCLING
If you encounter a damaged or cracked battery, immediately enclose it in a plastic bag and call your authorized
Pride Provider for instructions on disposal. Your authorized Pride Provider will also have the necessary informa-
tion on battery recycling, which is our recommended course of action.
26
Rally/RevF/September 03
Download from Www.Somanuals.com. All Manuals Search And Download.
V I . BATTERIES AND CHARGING
Why do my new batteries seem weak?
Deep-cycle batteries employ a different chemical technology than that used in car batteries, nickel-cadmium bat-
teries (nicads), and other common battery types. Deep-cycle batteries are specifically designed to provide power,
drain down their charge, and then accept a relatively quick recharge.
We work closely with our battery manufacturer to provide batteries that best suit your scooter’s specific electrical
demands. Fresh batteries arrive daily at Pride and are shipped fully charged to our customers. During shipping, the
batteries may encounter temperature extremes that can influence their initial performance. Heat diminishes the
charge on the battery; cold slows the available power and extends the time needed to recharge the battery.
It may take a few days for the temperature of your scooter’s batteries to stabilize and adjust to their new room or
ambient temperature.
More importantly, it takes a few charging cycles (partial draining followed by full recharging) to establish the critical
chemical balance that is essential to a deep-cycle battery’s peak performance and long life.
Follow these steps to properly break-in your scooter’s new batteries for maximum efficiency and service life.
1. Fully recharge any new battery prior to its initial use. This charging cycle brings the battery up to about 88% of
its peak performance level.
2. Operate your new scooter in familiar and safe areas. Drive slowly at first, and do not travel too far from your
home or familiar surroundings until you have become accustomed to your scooter’s controls and have properly
broken in your scooter’s batteries.
3. Fully recharge the batteries. They should be at over 90% of their peak performance level.
4. Operate your scooter again.
5. Fully recharge the batteries again.
6. After four or five charging cycles, the batteries are able to receive a charge of 100% of their peak performance
level and are able to last for an extended period of time.
What about public transportation?
If you intend to use public transportation with your scooter, you must contact the transportation Provider in ad-
vance to determine their specific requirements.
How should I store my scooter and its batteries?
See XII. “Care and Maintenance.”
Rally/RevF/September 03
27
Download from Www.Somanuals.com. All Manuals Search And Download.
V I I . O P E R A T I O N
BEFORE GETTING ON YOUR SCOOTER
n Have you fully charged the batteries? See VI. “Batteries and Charging.”
n Is the manual freewheel lever in the drive (down) position? Never leave the manual freewheel lever pulled up
unless you are manually pushing your scooter.
GETTING ONTO YOUR SCOOTER
1. Make certain that the key is removed from the key switch.
WARNING! Never attempt to board or exit your scooter without first removing the key
from the key switch. This will prevent the scooter from moving if accidental throttle
control lever contact is made.
2. Stand at the side of your scooter.
3. Disengage the seat lock lever and rotate the seat until it is facing you.
4. Make certain that the seat is locked securely in position.
5. Position yourself comfortably and securely in the seat.
6. Disengage the seat lock lever and rotate the seat until you are facing forward.
7. Make certain that the seat is locked securely in position.
8. Make certain that your feet are safely on the floorboard.
PRE-RIDE ADJUSTMENTS AND CHECKS
n Is the seat at the proper height? See VIII. “ ComfortAdjustments.”
n Is the seat locked securely in place?
n Is the tiller at a comfortable setting and locked securely in place? See VIII. “ComfortAdjustments.”
n Is the key fully inserted into the key switch?
n Does the scooter’s horn work properly?
n Is your proposed path clear of people, pets, and obstacles?
n Have you planned your route to avoid adverse terrain and as many inclines as possible?
OPERATING YOUR SCOOTER
Keep both hands on the tiller and your feet on the floorboard at all times while operating your scooter. This driving
position gives you the most control over your vehicle.
n Set the speed adjustment dial to your desired speed.
n Press your thumb against the appropriate throttle control lever.
n The electromechanical disc park brake automatically disengages and the scooter accelerates smoothly to the
speed you preselected with the speed adjustment dial.
n Pull on the left handgrip to steer your scooter to the left.
n Pull on the right handgrip to steer your scooter to the right.
n Move the tiller to the center position to drive straight ahead.
n To stop, slowly release the throttle control lever. The electronic brakes will automatically engage when your
scooter comes to a stop.
NOTE: Your scooter’s reverse speed is slower then that of the forward speed you preset with the speed
adjustment dial.
28
Rally/RevF/September 03
Download from Www.Somanuals.com. All Manuals Search And Download.
V I I . O P E R A T I O N
GETTING OFF OF YOUR SCOOTER
1. Bring your scooter to a complete stop.
2. Remove the key from the key switch.
3. Disengage the seat lock lever and rotate the seat until you are facing toward the side of your scooter.
4. Make certain that the seat is locked securely in position.
5. Carefully and safely get out of the seat and stand to the side of your scooter.
6. You can leave the seat facing to the side to facilitate boarding your scooter next time.
POWER DOWN TIMER FEATURE
Your scooter is equipped with an energy saving auto power down timer feature designed to preserve your scooter’s
battery life. If you mistakenly leave the key in the key switch and in the “on” position but do not use your scooter
for approximately 20 minutes, the scooters controller shuts down automatically. Although the controller is shut
down, power will still be supplied to the scooters lighting system.
If the power down timer feature takes effect, perform the following steps to resume normal operation.
1. Remove the key from the key switch.
2. Reinsert the key and power up your scooter.
Rally/RevF/September 03
29
Download from Www.Somanuals.com. All Manuals Search And Download.
V I I I . C O M F O R T A D J U S T M E N T S
TILLER ANGLE ADJUSTMENT
WARNING! Remove the key from the key switch before adjusting the tiller or the seat.
Never attempt to adjust the tiller or the seat while the scooter is in motion.
You can adjust the tiller to many positions.The tiller adjustment lever locks the tiller in place. It has a spring-loaded
mechanism that enables you to rotate it and change its position.
1. Turn the tiller adjustment lever counterclockwise until it is loose. If the tiller adjustment lever comes in contact
with the tiller basket, pull it outward, turn it clockwise, and release it. Continue to loosen until the tiller is able
to move. See figure 10.
2. Press the release buttons and move the tiller to a comfortable position. See figure 10A.
3. Turn the tiller adjustment lever clockwise until it is tight. If the tiller adjustment lever comes in contact with the
tiller basket, pull it outward, turn it counterclockwise, and release it. Continue to turn the lever until it is tight.
The tiller may be lowered to the center of the floorboard and locked in place for storage. See IX. “Disassem-
bly andAssembly.”
TILLER ADJUSTMENT
LEVER
TILLER ADJUST-
SLIDE LEVER OUT
TO REPOSITION
MENT LEVER
TILLER BOOT
RELEASE
BUTTONS
TILLER RELEASE
BUTTON
Figure 10A. Adjusting The TillerAngle
Figure 10. Adjusting the TillerAngle
SEAT HEIGHT ADJUSTMENT
The seat can be repositioned to one of three different heights.
See figure 11.
1. Push forward on the seat lock lever and lift the seat up
and off of the scooter. See figure 12.
2. Use the attached ring to pull and remove the ball detent
pin from the lower seat post.
LOCATING HOLES
BALL DETENT PIN
UPPER SEAT POST
LOWER SEAT POST
3. Raise or lower the upper seat post to the desired seat
height.
4. While holding the upper seat post at that height, match up
the holes in the upper seat post with the holes in the lower
seat post.
5. Fully insert the ball detent pin.
6. Replace the seat.
Figure 11. Seat Height Adjustment
30
Rally/RevF/September 03
Download from Www.Somanuals.com. All Manuals Search And Download.
V I I I . C O M F O R T A D J U S T M E N T S
FRONT-TO-BACK SEAT ADJUSTMENT
SEAT
PLATFORM
You can reposition the scooter’s seat forward or back-
ward to one of three settings to adjust the distance
between the seat and the tiller. See figure 12.
1. Remove the seat from your scooter.
2. Remove the four bolts that fasten the seat to the
seat platform. See figure 12.
SEAT LOCK
LEVER
SEAT
BOLTS
3. Align the seat platform with the desired set of holes
on the seat.
4. Install the four bolts securely.
Figure 12. Front-To-Back Seat Adjustment
ARMREST WIDTH ADJUSTMENT
The armrest width of your scooter can be adjusted
inward or outward. See figure 13.
ARMRESTS
1. Loosen the adjustment knobs at the back of the
seat frame.
2. Slide the armrests in or out to the desired width.
3. Tighten the adjustment knobs.
ADJUSTMENT
KNOBS
NOTE: The armrests also raise up, making get-
ting onto and off of your scooter easier.
SEAT
FRAME
Figure 13. Armrest Width Adjustment
SEAT ROTATION
The seat lock lever locks the seat in one of eight posi-
tions. See figure 14.
1. Push forward on the seat lock lever to unlock the
seat.
2. Rotate the seat to the desired position.
3. Release the seat lock lever to lock the seat securely
in place.
PUSH
FORWARD
TO ROTATE
SEAT
Figure 14. Seat Lock Lever
Rally/RevF/September 03
31
Download from Www.Somanuals.com. All Manuals Search And Download.
I X . D I S A S S E M B LY A N D A S S E M B LY
Always disassemble or assemble your scooter on a level, dry surface with sufficient room for you to work and
move around your scooter. Keep in mind that the disassembled sections of the scooter take up more floor space
than the assembled scooter.
DISASSEMBLY
WARNING! Lifting weight beyond your physical capability may result in personal injury.
Ask for assistance when necessary while disassembling or assembling your scooter.
1. Remove the key from the key switch. See V. “Your Rally.”
2. Push down on the manual freewheel lever. See V. “Your Rally.” Putting your scooter in drive mode may make
it easier for you to maneuver the rear section because the drive wheels are stabilized.
3. Lift the seat up and off of your scooter.
4. Gently lift the rear shroud off of your scooter.The rear shroud is held in place with a reusable fastener.
5. Unplug both battery harness connectors. See figure 15.
6. Remove the battery straps and lift both batteries from the battery wells.
7. Unplug the large, white, 9-pin front-to-rear connector that connects the front control console assembly har-
ness to the electronic controller assembly harness. See figure 15.
CAUTION! Failing to unplug both battery harness connectors and the front-to-rear
connector prior to further disassembly could result in permanent damage to your scooter.
FRONT-TO-REAR LOCKING LEVER
BATTERY HARNESS CONNECTORS
FRONT-TO-REAR CONNECTOR
LOCKING PIN
Figure 15. Battery Harness Connectors/
Front-to-Rear Connector
Figure 16. Front-To-Rear Locking Lever
Separating The Front And Rear Sections
1. Lower the scooter’s tiller to the center of the floorboard by turning the tiller adjustment lever counterclockwise
until it is loose. Press the tiller release buttons and lower the tiller to the center of the floorboard. Tighten the
tiller adjustment lever.
2. Pull up on the front-to-rear locking lever (releases the locking pin) with one hand, and push on the seat
pedestal to pivot the scooter’s rear section backward with your other hand—far enough so the rear section’s
upper pegs come free of the front section’s upper slots. See figures 16 and 17.
3. With one hand on the seat pedestal and one hand on the frame handle, slightly lift the front section and slide the
front and rear sections apart. See figures 17 and 18.
32
Rally/RevF/September 03
Download from Www.Somanuals.com. All Manuals Search And Download.
I X . D I S A S S E M B LY A N D A S S E M B LY
UPPER SEAT POST
FRAME LOCK UP
Figure 18. Frame Separation
Figure 17. Frame Handle
ASSEMBLY
1. Push down on the manual freewheel lever. See V. “Your Rally.” Putting your scooter in drive mode may make
it easier for you to maneuver the rear section because the drive wheels are stabilized.
2. Position the front and rear sections of your scooter as shown in figure 18.
3. Gently pull up on the upper seat post so the front of the rear section pivots up.
4. Using the frame handle, lift the front section and align the lower slots on the rear of the front section with the
corresponding lower pegs on the front of the rear section. Pivot the rear section forward until it locks in place
with a “click.” See figure 17.
5. Raise the tiller to the upright position by turning the tiller adjustment lever counterclockwise until it is loose.
Press the release buttons and raise the tiller to the desired position. Tighten the tiller adjustment lever.
6. Connect the large, white, 9-pin front-to-rear connector located on the harness coming out of the scooter’s
front section to the connector’s mating socket found near the front of the scooter’s rear section.
7. Place the batteries in the battery wells and strap them in place.
8. Connect the 2-pin battery harnesses into the mating harnesses that extend from the electronic controller as-
sembly.
9. Gently place the rear shroud over the seat pedestal and slide it down into position. The reusable fasteners hold
it in place.
10. Carefully lift the seat and slide the post (on the bottom of the seat frame) into the seat pedestal.
11. Rotate the seat until it locks into place to complete the assembly of your scooter.
Rally/RevF/September 03
33
Download from Www.Somanuals.com. All Manuals Search And Download.
X . O P T I O N A L A C C E S S O R I E S
OPTIONAL ACCESSORIES
For information concerning these optional accessories, contact your authorized Pride Provider.
Oxygen Tank
Holder
Dual Cane/Crutch
Holder
Single Cane/
Crutch Holder
Walker Holder
Forearm Crutch
Holder
Taillight
Rear Basket
Safety Flag
Quad Cane Holder
Cup Holder
Double Crutch Holder
Also Available but not shown:
Saddle Bag (Arm Mount)
34
Rally/RevF/September 03
Download from Www.Somanuals.com. All Manuals Search And Download.
X I . T R O U B L E S H O O T I N G
Any electromechanical device occasionally requires some troubleshooting. However, most of the problems that
may arise can usually be solved with a bit of thought and common sense. Many of these problems occur because
the batteries are not fully charged or because the batteries are worn down and can no longer hold a charge.
If you experience any problems with your scooter that you are unable to handle, immediately contact your autho-
rized Pride Provider for information, maintenance, and service.
PROBLEM
POSSIBLE SOLUTIONS
One of the following actions may eliminate the problem.
n
n
n
n
Remove and reinsert the key in the key switch.
Ensure the batteries are fully charged.
Push in the main circuit breaker reset button.
Ensure both battery harnesses are firmly connected to the
electronic controller assembly and to the battery terminals.
Ensurethefront-to-rearharnessconnectorisfirmlyconnected.
All of my scooter systems appear to be “dead.”
n
Ensure your scooter was not left in freewheel mode.
(Push down on the manual freewheel lever to restore normal
operation.)
My scooter’s battery condition meter shows a full charge,
but my scooter does not move when I push the throttle.
NOTE: When the manual freewheel lever is pulled up, your
scooter’s brakes are disengaged and all power to the motor/
transaxle assembly is cut.
One of the following actions may eliminate the problem.
My scooter’s main circuit breaker repeatedly trips.
n
n
Charge your scooter’s batteries more frequently.
Have both of your scooter’s batteries load tested by your
authorized Pride Provider.
n
Obtain a battery load tester at most any automotive parts
store; follow the directions supplied with the load tester.
One of the following actions may eliminate the problem.
My scooter’s battery condition meter dips way down and
the motor surges or hesitates when I press the throttle
control lever.
n
n
n
Fully charge your scooter’s batteries.
Have yourauthorized Pride Providerload test each battery.
Obtain a battery load tester at most any automotive parts
store; follow the directions supplied with the load tester.
Rally/RevF/September 03
35
Download from Www.Somanuals.com. All Manuals Search And Download.
X I I . C A R E A N D M A I N T E N A N C E
Your scooter requires a minimal amount of care and maintenance. If you do not feel confident in your ability to
perform the maintenance listed below, you may schedule inspection and maintenance at your authorized Pride
Provider.The following areas require periodic inspection and/or care and maintenance.
TIRE PRESSURE
n If equipped with pneumatic tires, always maintain a proper 30-35 psi tire pressure.
WARNING! It is important that 30-35 psi tire pressure be maintained in pneumatic tires at
all times. Do not underinflate or overinflate your tires. Low pressure may result in loss of
control, and overinflated tires may burst. Failure to maintain 30-35 psi tire pressure in
pneumatic tires at all times may result in tire and/or wheel failure, causing serious personal
injury and/or damage to your scooter.
n Regularly inspect your scooter’s tires for signs of wear.
EXTERIOR SURFACES
Bumpers, tires, trim ,and the tiller boot can benefit from an occasional application of rubber or vinyl conditioner.
WARNING! Do not use a rubber or vinyl conditioner on the scooter’s vinyl seat, floorboard,
or tire tread. They will become dangerously slippery and result in personal injury and/or
damage to your scooter.
BATTERY TERMINAL CONNECTIONS
n Make certain that the terminal connections remain tight and uncorroded.
n The batteries must sit flat in the battery wells.
n The battery terminals should face the rear of the scooter.
WIRING HARNESSES
n Regularly check all wiring connections.
n Regularly check all wiring insulation, including the charger power cord, for wear or damage.
n Have your authorized Pride Provider repair or replace any damaged connector, connection, or insulation that
you find before using your scooter again.
ABS PLASTIC SHROUDS
n The front tiller shroud, front shroud, and the rear shroud are formed from durableABS plastic and are coated
with an advanced formula urethane paint.
n A light application of car wax will help the shrouds retain their high gloss.
AXLE BEARINGS AND THE MOTOR/TRANSAXLE ASSEMBLY
These items are all prelubricated, sealed, and require no subsequent lubrication.
MOTOR BRUSHES
The motor brushes are housed inside of the motor transaxle/assembly. They should be inspected periodically for
wear by your authorized Pride Provider.
36
Rally/RevF/September 03
Download from Www.Somanuals.com. All Manuals Search And Download.
X I I . C A R E A N D M A I N T E N A N C E
CONSOLE, CHARGER, AND REAR ELECTRONICS
n Keep these areas free of moisture.
n Allow these areas to dry thoroughly if they have been exposed to moisture before operating your scooter again.
STORING YOUR SCOOTER
If you plan on not using your scooter for an extended period of time, it is best to:
n Fully charge its batteries prior to storage.
n Disconnect the batteries from the scooter.
n Store your scooter in a warm, dry environment.
n Avoid storing your scooter where it will be exposed to temperature extremes.
WARNING! Always protect batteries from freezing temperatures and never charge a frozen
battery. This damages the battery and can cause personal injury.
For prolonged storage, you may wish to place several boards under the frame of your scooter to raise it off of the
ground. This takes the weight off the tires and reduces the possibility of flat spots developing on the areas of the
tires contacting the ground.
Rally/RevF/September 03
37
Download from Www.Somanuals.com. All Manuals Search And Download.
X I I I . W A R R A N T Y
THREE-YEAR LIMITED WARRANTY
Three years on all structural frame components; including platform, fork, seat post, and frame.
Three-year prorata drive train warranty; including transaxle, motor, and brake.
n First year: 100% replacement of parts cost
n Second year: 67% replacement of parts cost
n Third year: 50% replacement of parts cost
THREE-YEAR WARRANTY EXCEPTIONS
Transaxle: In cases where there is an increase in the operational noise level, the warranty does not apply. (The
increase in operational noise level usually occurs due to abusive and excessive strain on the scooter.)
Motor brake: Three-year warranty for the electrical function of the motor brake. Brake pads are a wear item and
are not warranted.
ONE-YEAR LIMITED WARRANTY
For one (1) year from the date of purchase, Pride will repair or replace at our option to the original purchaser, free
of charge, any part or electronic component found upon examination by an authorized representative of Pride to be
defective in material and/or workmanship.
The battery is warranted by the battery manufacturer. The battery is not warranted by Pride.
Warranty service can be performed by Pride or by an authorized Pride Provider. Do not return faulty parts to Pride
without prior consent.All transportation costs and shipping damage incurred while submitting parts for repair or
replacement are the responsibility of the original purchaser.
WARRANTY EXCLUSIONS
n ABS plastic shrouds and footrest covers (wear items and not warranted)
n Batteries (the battery manufacturer provides a limited warranty)
n Tires and tire tubes (wear items and not warranted)
n Upholstery and seating (wear items and not warranted)
n Repairs and/or modifications made to any part of the scooter without specific and prior consent from Pride
n Circumstances beyond the control of Pride
n Damage caused by: battery fluid spillage or leakage, abuse, misuse, accident, or negligence, improper opera-
tion, maintenance, or storage, commercial use or use other than normal
n Labor, service calls, shipping, and other charges incurred for repair of the product
There is no other express warranty.
Implied warranties, including those of merchantability and fitness for a particular purpose, are limited to one (1)
year from the date of original purchase and to the extent permitted by law.Any and all implied warranties are
excluded. This is the exclusive remedy. Liabilities for consequential damages under any and all warranties are
excluded.
Some states do not allow limitations on how long an implied warranty lasts or do not allow the exclusion of limitation
of incidental or consequential damages. So, the above limitation or exclusion may not apply to you.
38
Rally/RevF/September 03
Download from Www.Somanuals.com. All Manuals Search And Download.
182 SusquehannaAve.
Exeter, PA 18643
1-800-800-8586
Download from Www.Somanuals.com. All Manuals Search And Download.
|